Power Meter ME96NSR Catalog

8/13/2019 Power Meter ME96NSR Catalog

1/32

MITSUBISHI ELECTRONIC MULTI-MEASURING INSTRUMENT

ME96NSRMODEL


2/32

MITSUBISHI Electronic Multi-Measuring Instrument NS Series features high performanceand crystal clear display.

With simple operating functions, NS Series is the best support your measuring and moni-toring systems.

16

23262829

Upper/lower limit monitoring up to 4 itemsHarmonics monitoringMeasures import/export active energy

4 items displayableBacklight automatic off function

ModBus communicationCC-Link communication

Simple settingsSimple operations

Output functions for 7 itemsPulse width settablePulse output at 2 points

Analog output range settable

DIN Size 9696mm3P4W/3P3W Common Use

Add-on Type Output OptionsCE MarkingConforms to EU RoHS Directive( 2002/95/EC )

FeaturesFunctions

Dimensions / Mounting / WiringSpecificationsRelated ProductsSafety Precaution


3/32

F eature sModBus Transmission System (ME96NSR-MB, Optional Plug-in Module ME-0052-NS96)

CC-Link Transmission System (ME96NSR, Optional Plug-in Module ME-0040C-NS96)

Analog Pulse Transimission System (ME96NSR, Optional Plug-in Module ME-4201-NS96)

RS485/RS232Converter

Central Monitor

RS485 (ModBus)

RS232

ModBus communication system to monitor computers. By adding the optional plug-in module ME-0052-NS96, monitoring of contact input

signal and ON/OFF of contact output signal can be controlled remotely. Digital input signal can be latched for over 30ms, and there is no need for external latch

circuits.Optional Plug-in ModuleME-0052-NS96

SHT (OFF)CC (ON)ALPALTALACB Status

Max. Baud Rate 38.4kbp Max. Connection Distance 1000m Max. Connection Units 31

Digital Input 5 points (24VDC) Digital Output 2 points (35VDC)

Optimum transmission system for remote monitoring using MITSUBISHI PLC.

Remote monitoring of contact signal leading to less wiring, less spacing. Digital input signal can be latched for over 30ms, and there is no need for external latch

circuits.

Abnormal Signal (Facility)

Abnormal Signal (Earth Leakage)

Abnormal Signal (Temperature)

Circuit Breaker Status Signal etc

Max. Baud Rate 10Mbps Max. Connection Distance 100m (10Mbps)

to 1000m (156kbps) Max. Connection Units 42 Digital Input 4 points (24VDC)

CC-Link

NETWORK

MELSEC Series

NETWORK

Can remotely monitor A, DA, V, W, var, VA, PF, Hz, Harmonics Current RMS Value,and Harmonics Voltage RMS Value at 4 to 20mA output. (Max. of 4 outputs)

Active energy and reactive energy can be remotely monitored by pulse output.(Max. of 2 pulses)

Can remotely monitor upper/lower limit alarm by contact output. (Max. 1 point)

4 to 20mA 4 outputs Maximum 600 No-voltage a contact

35VDC 0.1A Pulse width 0.125, 0.5, 1s is selectable No-voltage a contact 35VDC 0.2A

Analog OutputPulse OutputAlarm Output

Basic Device

Model NameME96NSR

ME96NSR-MB

Transmission

ModBus Communication Optional Plug-in Modules

Model NameME-4201-NS96ME-0040C-NS96ME-0052-NS96

Analog Output4

Pulse Output2

Contact Input45

Contact Output (Note)

12

Transmission Function

CC-Link

Used withME96NSR

ME96NSR-MB(Note): Contact Output for ME-4201-NS96 closes at the time of high and low alarm occurrence. Contact Output for ME-0052-NS96 switches according to 16 bit set of ModBus communication.

1


4/32

(1) All Phase Simultaneous Display

Displays measuring value for each phase digitally, and shows average value or total value by bar graph.

(2) Four Measuring Items Simultaneous Display

Four measuring items can be displayed simultaneously by tri-level digital display and bar graph.

(3) Special Display by Display Pattern P00

Display can be selected as desired in Display Pattern P00.

Average Current Average Voltage Total Electricity

Note: Average value or total value can be displayed by numbers by pressing the PHASE button.

< Functions Available >

Keep the display unchanged. Keep the display unchanged even when DISPLAY button is pressed.

Use ME96NSR instead of electric energy meter by displaying electric power.

Set onlyone display

Note: Digital display of each phase is possible by pressing the PHASE button.

DISPLAY DISPLAY DISPLAY


Upper : Select from A, DA, V, W, var, VA, PF, Hz

Middle : Select from A, DA, V, W, var, VA, PF, Hz

Under : Select from A, DA, V, W, var, VA, PF, Hz, Wh, varh

Maximum of four displays can be set.

Desired Display can be ChosenDesired display can be chosen by selecting from existing patterns or selecting displays. (For the details of display patterns, please refer toDisplay Pattern Contents on page 22.)

F eature sVariety of Display Functions

2


5/32

Note: Alarm Indicator blinks when it is set on alarm mode.

(1) Bar Graph Fixed Display

Measuring items displayed by bar graph can be fixed. shows that display is fixed.Also, display can be changed between average voltage, average current, total power, total reactive power, total power ratio, frequency bypressing , button.

(2) Digital Value Display by Bar Graph

Values shown on the tri-level digital display can be displayed by bar graph. (Except when the tri-level display is measuring the same items)Bar graph shows the digital value of .

Bar GraphEach measuring items can be displayed by a bar graph. With bar graph display, one can grasp the rated value and percentage against the alarmvalue instantly.

Maximum/Minimum Value DisplayThe maximum and minimum value of each measuring items can be displayed. Both the maximum and minimum value show the current status,so monitoring by the maximum and minimum value is possible. Also, range of minimum value to maximum value is shown by bar graph.

Cyclic DisplayIn cyclic display, the display changes automatically every five seconds. Even when this device is used in a very high place or inside of a panel,measuring items and measuring value of each phase can be checked without pushing DISPLAY , PHASE buttons.

Alarm Indicator

+

+

+

+ + +

Value shown by bar graph

Alarm Indicator

Operation Behavior

Press DISPLAY for 2 seconds Measuring items change automatically every 5 seconds

Press PHASE for 2 seconds Phase display changes automatically every 5 seconds


< Features of Cyclic Display >

Cyclic display can display current status, maximum/minimum value Cyclic display continues even after power failures (No need for cyclic display operation)

+

3


6/32

Measuring Functions

Harmonics MeasurementMeasuring of harmonics current, harmonics voltage is possible. This device can also be used for harmonics monitoring.

Harmonics Current

(other than phase N) Harmonics VoltageMeasuring

Items

Degree RMS Value Distortion Ratio

Harmonics Current(phase N)

RMS Value Distortion RatioRMS Value Distortion RatioSynthesis

1st3rd5th7th9th

11th13th

Note: When the 1st RMS value is 0 (zero), the distortion ratio shows 0% .

Measurement of Active Energy/Reactive EnergyThis device can be used to measure active power/reactive energy for particular type of power distribution facility, such as private powergenerating facility or condenser panel.

There are two ways of counting quadrant in measurement of reactive energy.

Wh varhEnergy Measurement

Setting (Sett ing 4.1) Imported Exported Imported Lag Imported Lead Exported Lag Exported LeadRemark

1

2Measurement of reactiveenergy is by 2 quadrants

3

4Measurement of reactiveenergy is by 4 quadrants

Measurement of 2 Quadrants/4 Quadrants by Reactive Energy

Pressing the , button at the same time for 2 seconds displays lower 3 digits. Small amount of value change of measuring value can bechecked.

Lower Digit Expanded Display

-varh(Imported lead + Exported lag)

+varh(Imported lag + Exported lead)

Press for 2 sec.

Decimal points shifts

Counts imported lag andexported lead as 1 segment,and imported lead andexported lag as 1 segment.Dead region occurs only inaround var=0 (Power ratio: 1).Since dead region does notoccur around Power ratio=0,

this is suited for facility withoutprivate power generator ormeasurement of reactivepower with condenser load ofPower ratio=0.

Counts each import lag, importlead, export lag, and exportlead as one segment.It is generally felt that a deadregion occurs in the border ofeach segment.This is suited for measurementof facilities with private power

generators.

F eatures

Accurate Measurement by Our Own ASICOur own ASIC allows for accurate measurements. (For details on measurement accuracy, please refer to Specifications on page 26.)

+var

-var

+W-W

Exportedlag

Exportedlead

Importedlead

Importedlag

+var

-var

+W-W

Exportedlag

Exportedlead

Importedlead

Importedlag

Lower digit expanded display is displayed onlywhen active/reactive energy is shown on the display.When the expanded display is operated duringactive energy screen, reactive energys lowerdigit is not expanded. For displaying lower digitsreactive energy, please operate by displayingreactive energy screen.

Note:

+

+ ,

4


7/32

No lower limit alarm on 0A, 0V.

Monitoring of Upper/Lower Limit

Even during a setup of a facility, where no current/voltage input is found, analog output, pulse output, contact output, and communication data isreplied. This allows for checkup of wiring and monitoring program system.

Current

Time

Upper LimitValue

Lower LimitValue

MotorStrikingCurrent

Alarm DelayTime

Alarm DelayTime

Maximum Value Update

Minimum Value Update

AlarmGeneration

Monitoring of Upper/Lower Limit (Max. 4 points)There is an output of upper/lower limit alarm when plug-in optional module ME-4201-NS96 is mounted.(Since contact output is 1 point, it becomes OR output set in upper/lower limit alarm item)

Test Function

Setting of Alarm Output DelayTime of alarm output after the maximum value and minimum value is reached can be set.With this function, alarm output caused by frequency change at start-up current of a motor and start-up of private power generating facility can beavoided.Furthermore, maximum value and minimum value do not update during alarm delay.

Alarm occurrence status can be checked by current status display and maximum/minimum value display. Upper/Lower Limit Alarm Display by LCD

No alarm output andmaximum/minimumvalue update duringalarm delay time.

5


8/32

Functions of Buttons

Settings

LEAD statusLAG statusScale of the bar graphOutside rangeAlarm indicatorBar graph status

Phase statusUnitMetering statusHarmonicsCommunication statusAlarm statusTest statusSetup statusDigital

They show direction of Power Factor or Reactive Power on bar graph.They show the type of counting of Reactive Energy on Reactive Energy Display.They show the scales of the bar graph.Measurement value is outside range of scale of the bar graph.It shows the setting value of the upper limit or lower limit.They show the item expressed with the bar graph.

They show the phase for each of the digital displays.They show the unit for each of the digital displays.When it is blinking, the instrument is counting active energy.It means that the digital displays are harmonics values.It shows that the instrument is equipped with a communication function.They show that the upper limit value or lower limit value was exceeded.It shows that the output of the option module is tested.It appears at Set-up mode.The measured value is displayed in a digital number.

123456

789

101112131415

snoitcnuFButtonssnoitcnuF OperationsSpecial functionsBasic functions

Buttons

SET

orMAX/MINPHASE

DISPLAY

Set up setting items such as primary voltage or primary

current, and choose and indicate setting items.Change settings and bar graph display.Change display from Max/Min to instantaneous value.Change phases.Change display.

Press for 2 sec.

Press for 2 sec.Press for 2 sec.Press for 2 sec.Press for 1 sec.

DISPLAY

PHASE&

& RESETor

Manual display change Cyclic display change

Manual phase change Cyclic phase changeZoom display of Wh, varh values (last 3 digits)Reset all the Max/Min values.Fast forward or fast return values when setting.Reset Wh, varh values to zero by holding down the buttons for 2 sec.SET & RESET & PHASE

For correct measurement, it is necessary to set the primary voltage and the primary current, etc. in the Set-up mode. It can set necessary items,after it shifts from the Operation mode to Set-up mode. Items not set are on the initial setting. In case of regular use, it can be used by setting onlythe Set-up menu 1(basic set-up).In case of using the communication function, set Set-up menu 2. Refer to the next page or later for the set-up items.

Note: The above display is an example for explanation.

Set-up Diagram

Press SET and RESET simultaneously for 2 seconds to get in theSet-up mode.

Select a Set-up menu number by or . Change the contents in each Set-up menu. (Refer to pages 7-14.)

After completion of set-up, select End in the Set-up menu and press.

When the End display appears, press once again.+ SET

SET

Shift from the operation mode tothe set-up mode.

Press them simultaneouslyfor 2 seconds.

Press themsimultaneously for 1second.Press themsimultaneously for 1second.

Shift from the operation mode tothe set value confirmation mode.Select the menu number to set orEnd.Get into each setting screen. Shiftto the next setting item.Go back to the previous settingitem.

Memorize the setting contents, andgo back to the operation mode.

Skip remaining setting itemsduring setting.Shift from the set-up mode tosimplified set-up menu.

Change the page of the simplifiedset-up menu.

Phasewire

Displaypattern

Using VT/ direct input

Direct

voltage

Secondaryvoltage

Primaryvoltage

Secondarycurrent

Primarycurrent

Time constantfor currentdemand

Phasewire

Displaypattern

Using VT/ direct input

Direct

voltage

Secondaryvoltage

Primaryvoltage

Primarycurrent


CC-Link stationnumber

Communicationmethod

ModBusaddress

ModBusbaud rates

ModBusparity

ModBusstop bit

CC-Link baud rates

Communicationmodule reset

Expandedcounting

Harmonics

Digitalinput/output

Back light

ON/OFF

Currentdisplay

digit

Voltagedisplay

digit

Activepower

display digit

Reactivepower

display digit

Apparentpower

display digit

Communicationmethod

ModBusaddress

ModBusbaud rates

ModBus

parity

ModBusstop bit

CC-Link baud rates


Digital inputreset

Currentmaximum

scale

Active powermaximum

scale

Reactive powermaximum

scale

Power

factor scale

Analogoutput 1

Analogoutput 2

Analogoutput 3

Analogoutput 4

Analogoutput limit

Alarmitem

Alarmvalue

Alarmdelay time

Operation mode

Measurement display

Action

Select a set value.

Shift to the End screen.

Select CANCEL.

Cancel the setting.

Display the type of option unit.

Initializing of instrument

Key operation

Press it for 2 seconds.

Press it several times.

Press it.

Press it.

Press it several times.

Press it.

Press it.

Press it.

Press it.

Press it for 1 second.

Press it.

or

or

or

Omittedin figure

Arrow infigure

+

+

+

Set-up mode or set value confirmation mode

Set-up menu End

End displayType of optiondisplay

P-1

P-2

CANCEL display

Example ofset-up mode

Set-up menu 1 Set-up menu 2 Set-up menu 3 Set-up menu 4

Analogoutput 1 Adj.

Analogoutput 2 Adj.

Analogoutput 3 Adj.

Analog

output 4 Adj.

Pulseoutput 1

Pulsewidth

Set-up menu 5 Set-up menu 6 Set-up menu 8Set-up menu 7

S i m p

l i f i e d s e

t - u p m e n u

blink extinction

Pulseoutput 2

CC-Link stationnumber

Alarmcancelmethod

+

+

SET

SET

SET

SET

SET

SET

SET

RESET

PHASE DISPLAY

DISPLAY

PHASE

PHASE

MAX/MIN

+

InitializingprocessShift

automatically

(Example)

Example of set valueconfirmation mode

14

1 2

13 12 11 10

9

8

54

3

4

6

7

15

This figure writes all set menus.There is a menu not displayedby the presence of the settingcondition and the option.

CAUTION

1. Make sure to set for Directvoltage, Secondary voltage,Primary voltage, Secondarycurrent, Primary current.

(Or check the set-up contents.)A correct measurement cannotbe done if the set-up contentsare wrong.

2. Set for the other set-up contentswhen it is necessary.When it is not done, it operateswith the initial contents.

Functions of LCD

F unction s

How to access Set-up

6


9/32

SET RESET

Settings (Continued)

Setting ProcedureDisplay the setting screen with , and setup the items with / .Settings can be registered for each setup menu number. Display the [End] screen and register with .

+ SETSET

Set-up menu

Phase wire

Display pattern

Using VT/direct input

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

SET

DISPLAY SET

DISPLAY SET

Set the set-up menu number to 1.

Set the phase wire system.

Three phase 3-wire (2CT)Three phase 3-wire (3CT)Three phase 4-wire

3P3.2Ct3P3.3Ct3P4

:::

Set the display pattern. (Initial content: P13)

Choose VT or direct input (without VT).

P01P02P03P04P05P06P07P08P09P10P11P12P13P00

A DA V W PF var Hz varhVA Wh HI HV DI DO

Direct voltage

Set-up the rated voltage for scaling of the bar graph. If you set YES on set up No. , this display does not appear.

110V/63.5V173V/100V190V/110V380V/220V

415V/240V440V/254V480V/277V

110V 220V

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

VT secondary voltage

CT secondary current

Set the secondary voltage values of VT.If you set no on set up No. , this display does not appear.

63.5V100V110V115V120V

100V110V220V

+ ,

+ ,

VT primary voltage

CT primary current

Set the secondary current value of CT.

SET DISPLAY

+ ,SET DISPLAY

Time constant forcurrent demand

Set the primary current value of CT. (The initial value is 5A.)DISPLAY SET

5A 1A

Set-up menu

According to the set-up diagram (page 6), save the changedcontents, or continue to the other set-up menu.

Set up the time constant for calculating current demand.

In this set-up menu 1, set-up the basic contents as following for correct measurement .

In the operation mode, press and simultaneously for 2 seconds or more, and the following operation becomes available.The underline shows the initial value.

Set-up Menu 1 (Basic Set-up)

Note: As for detailed display patterns, refer to page 22.: Displayed in display setting: Set by the set-up menu 4 (page 9): Select P00, and set display sequence and display

position (Please refer to the users manual)

DA : current demand, HI: harmonic current, HV: harmonic voltageDI : digital input, DO: digital output (DI/DO: only when option module is installed) VA : Three phase 4-wire only

Displaypattern

WhExportedactive

energy

varhSpecial

YESno

: using VT: direct input

Initial setting Three phase 3-wire : using VT Three phase 4-wire : direct input Three phase 4-wire

(phase to phase(L-L)/phase to neutral(L-N))Three phase 3-wire(phase to phase(L-L))

Three phase 4-wire Three phase 3-wire Set the primary voltage value of VT in the case of using VT.

If you select no on set up No. , this display does not appear.Initial setting Three phase 3-wire : 10000V Three phase 4-wire : 200V

From top digit, select the value of the flickering digit by

The setting digit can be moved to right by SET .The setting digit can be moved to left by D ISPLAY .The number of settable digits are upper 3 digits. Setting isavailable in the range from 60V to 750kV (750000V).

If it is set on range other than 60V to 750kV, error display(E05) appears. At the moment of the error display, pressSET and review the set value, and set it once again.

When SET is pressed at the lowest digit, the setting itemgoes to the next one.

and .+

+

From top digit, select the value of the flickering digit by

The setting digit can be moved to right by SET .The setting digit can be moved to left by D ISPLAY .The number of settable digits are upper 2 digits. Setting isavailable in the range from 5A to 30kA (30000A).

If it is set on range other than 5A to 30kA, error display (E05)appears. At the moment of the errorand review the set value, and set it once again.

display, press SET

When SET is pressed at the lowest digit, the setting itemgoes to the next one.

and .

0 second10 seconds20 seconds30 seconds

40 seconds50 seconds

1 minute2 minutes

3 minutes4 minutes5 minutes6 minutes



Note: Even when the display pattern do not display the current demand, thisscreen appears. If the current demand is not necessary, press SET .

NoteIf the contents in the Set-up Menu 1 are changed, maximum value, minimum value, and demand value of related measurement items will be reset.(However, all of the counting values are not reset.)

7


10/32

Set-up Menu 2 (Set-up of Communication, Contact Input Reset Procedure)

Note

00.5

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

In the operation mode, press SET and RESET simultaneously for 2 seconds or more, and the following operation becomes available.

Set-up Menu 3 (Bar Graph Set-up)

In the operation mode, press SET and RESET simultaneously for 2 seconds or more, and the following operation becomes available.

1. Accuracy is defined to rated current. Although the maximum scale may display 120% or more of rated current and rated voltage in order to makethe scale easy to read, current input is within 100% of rated current.

2. When the display pattern that does not display power, reactive power, active energy, and reactive energy is selected, the setting item related tothem is skipped.

Set-up menu

Communication method

ModBus address

ModBus baud rates

ModBus parity

ModBus stop bit

Set-up menu

Set-up menu

Current maximum scale

Active power maximum scale

Active power scale

Reactive power maximum scale

Power factor scale

CC-Link station number


CC485

::

2400 bps4800 bps9600 bps19.2 kbps38.4 kbps

+ ,

+ ,

+ ,

Settable parity : nonoddEVEn

+ ,

+ ,

+ , CC-LinkModBus

CC-Link baud rates

Communication module reset

Digital input reset

Set-up menu

onoFF

0 : 156k1 : 625k2 : 2.5M3 : 5M4 : 10M

+ ,

+ ,

+ ,

+ ,

+ ,

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

SET

DISPLAY SET

DISPLAY SET

SET

DISPLAY SET

DISPLAY SET


F unction s

Set the CC-Link or ModBus as thecommunication method.This display appears only if the type ME96NSR-MBhas the type ME-0040C-NS96 option module.

Set the ModBus address number.


Set the current maximum scale.The maximum scale is set in the range of about 40%to about 120% of the rated current.

Set the single / double deflection of active power.

Set the power factor scale.

Set the maximum scale of active power.The maximum scale is set in the range of about 40%to about 120% of the rated full load power.

Set the reactive power maximum scale.

According to the set-up diagram (page 6), save thechanged contents or continue to the other set-up menu.

In case of CC-Link, this display does not appear.

Settable addresses: 1 to 255 Set the ModBus baud rate.In case of CC-Link, this display does not appear.

Settable baud rate:

Set the ModBus parity.

In case of CC-Link, this display does not appear.

Set the ModBus stop bit.In case of CC-Link, this display does not appear.

Stop bit : 1Stop bit : 2

Set the CC-Link station number.

In case of ModBus, this display does not apper.

Settable addresses: 1 to 64 Set the CC-Link baud rates.

In case of ModBus, this display does not apper.

Settable baud rates:

Reset of communication module.In case of ModBus, this display does not apper.

Set it ON.

Note: When it is not set on ON, changed stationnumber and baud rate do not become valid. Set the digital input(DI) reset method.

Without digital input, this display does not apper.

HoLd: Manual methodAuto: Automatic method

Note: When selected the manual method(HoLd), input state is kept until thecancel operation is done manually. For the method of the cancel operation,refer to page 21.

Note: This insturuments rating is 100% value.

For the maximum scale value, please refer tothe users manual.

Note: This insturuments rating is 100% value. For the maximum scale value, please refer to

the users manual.


When + and are pressed, the scale value ofbar graph flickers at single / double deflection.

The setting method is same as that of maximum scale value of activepower.

8


11/32


12/32

F unction s

Set the alarm item to be allowed to measurement items.

+ ,

+ ,

+ ,

DISPLAY SET

DISPLAY SET

DISPLAY SET

SET

DISPLAY SET

DISPLAY SET

+ ,

+ ,

+ ,Set-up menu

Alarm cancelmethod

Set the alarm cancel method at generation of alarm. (screen, relay)

Set the alarm delay time.

Set the upper and lower limit alarm item 2 to 4 (AL2, AL3, AL4) in the same method.+ ,

Set-up menu

Alarm item 1

Alarm value 1

Alarm item 2 to 4

Alarm delay time, delay time of max/min value


Alarm itemA, DA, AN, DAN upper limit

A,DA lower limit

V upper limit

V lower limit

W, var upper limit

W, var lower limit

PF upper limit

PF lower limit

Hz upper limit

Hz lower limit

Set-up range5 to 100 to 120%

3 to 10 to 95%

25 to 110 to 135%

20 to 70 to 95%

95 to 100 to 120%

120 to 3 to 95%

0.05 to 1 to 0.05

0.05 to 0.5 to 0.05

45 to 65Hz

45 to 65Hz

5 to 35 to 120%

0.5 to 3.5 to 20%

Step1%

1%

1%

1%

1%

1%

0.05

0.05

1Hz

1Hz

1%

0.5%

Harmonic current total RMS value upper limit

Harmonic voltage total distortion ratio upper limit

Set the alarm value of alarm item 1.The set-up range is shown below.

Example display when Aupper limit is set to 100%

Note 1: The upper and lower limit alarm mark by the bar graph is displayed in the step of about 5%though the digital value can be set in the above-mentioned step on A, DA, V, W and var.However, the alarm is generated with the accuracy of the digital value. DA: current demand

Note 2: V alarm value is set according to the value of primary voltage (direct voltage).A, DA, W, and var is set for value of rated scale.

Note 1: A measurement item that is not selected in the display pattern can be selected.Note 2: The alarm of W, var, and PF is judged from the total RMS value.

The upper alarm of A and DA is judged from the phase of 1, 2, 3 and N.The lower alarm of A and DA is judged from the phase of 1, 2 and 3. (N is excluded.)

Note 3: The alarm of the total distortion ratio is judged from the phase of 1, 2 and 3.(N is excluded.)

nonA upper limitA lower limit

Demand A upper limitDemand A lower limit

V(L-L) upper limitV(L-L) lower limit

W upper limitW lower limit

var upper limitvar lower limitPF upper limitPF lower limitHz upper limitHz lower limit

Harmonic current totalRMS value

Harmonic voltage totaldistortion ratio

nonA upper limitA lower limit

AN upper limitDemand A upper limitDemand A lower limit

Demand A N upper limitV(L-N) upper limitV(L-N) lower limitV(L-L) upper limitV(L-L) lower limit


var upper limitvar lower limit

PF upper limitPF lower limitHz upper limitHz lower limit

Harmonic current total RMS valueHarmonic current phase N RMS valueHarmonic voltage total distortion ratio

Three phase 3-wire Three phase 4-wire

Display of non upperand lower limit alarm

Display when A upper limit is setto upper and lower limit alarm

If the condition of limit exceeding continues f or more than the delay time,the alarm generates.And if it does not continue during this time, the maximum/minimum valueis not updated.

0 seconds5 seconds

10 seconds20 seconds

30 seconds40 seconds50 seconds

1 minute


Display of automaticreset method

Display of manual reset

method

Method

Automatic(Auto)

Manual(HoLd)

Cancel method

When there is no alarm generating condition,

alarm is automatically reset.

Please refer to page 19 for details.

Alarm is reset by pressing RESET .Alarm continues until RESET is pressed.

According to the set-up diagram (page 6), save the changed contents or continue to the other set-up menu.

Set-up Menu 5 (Alarm Set-up)

SET RESET

This sets the upper and lower limit alarm. The upper and lower limit set value mark (blinking) is displayed on the bar graph. From the display items,four items can be set.In the operation mode, press and simultaneously for 2 seconds or more, and the following operation becomes available.


to

Refer to page 19 for details.

10


13/32


14/32

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

No.

Content No. Content

Simplified setting page: P-1

No. Content No. Content

Simplified setting page: P-2

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

SET

DISPLAY SET

DISPLAY SET

SET

DISPLAY SET

F unction s Set-up Menu 7 (Pulse Output Set-up)

SET RESETIn the operation mode, press and simultaneously for 2 seconds or more, and the following operation becomes available.When the ME-4201-NS96 optional plug-in module is not installed, this menu cannot be set.

Set-up Menu 8 (Analog Output Adjustment)

Set-up menu

Set-up menu

Pulse width

Pulse output item 1 pulse value

Pulse output item 2

Pulse output item 1

Pulse output item 2 pulse value



At initial setting, imported active energy is set to pulseoutput 1, press SET to go to the next setting.

Set the output element to pulse output 1.

Settable elementsExample of pulse output 1

Example of pulse output 2

Example of pulse output 1

Total load [kW] =1000

(Primary voltage) (Primary current)

Set the pulse value of pulse output 1.Pulse value is selected from the table below, according to total load [kW].

= 3 (Three-phase 4-wire)= 3 (Three-phase 3-wire)

In case of reactive energy, kW in the above tableis exchanged into kvar and kWh into kvarh.

Primary voltage value is calculated by phase t o newtral.

Pulse output 2 is set in the same method as pulse output item 1 set-up. (At initial setting, imported lag reactive energy is set to pulse output 2.)

Set the output element to pulse output 2.

Pulse output 2 is set in the same method as pulse output item 1 set-up.

Set the pulse value of pulse output 2.

0.125s 0.500s 1.000s

Note: When the pulse width is set to 0.500s, 1.000s, and pulse unitis set to lowest settable unit, pulse output cannot follow, and thecounting pulse may decrease when load is large.

Set the pulse width of output pulse.

When the ME-4201-NS96 optional plug-in module is installed, zero adjustment and span adjustment of analog output is possible.(Only for circuits set on analog output)Please adjust it only when the matches with the receiving instrument or the output have changed.In the operation mode, press and simultaneously for 2 seconds or more, and the following operation becomes available.SET RESET

Phase wire

Display pattern

Using VT/direct input

Direct voltage


VT primary voltage

CT primary current

Time constant for current demand

Communication method

ModBus address

ModBus baud rates

ModBus parity

ModBus stop bit


CC-Link baud rates

Communication module reset

Set-up menu

Set-up menu

Span Adj. for CH1

Zero Adj. for CH1

CH2, CH3 and CH4can be adjusted thesame as above.

Simplified Set-upThe setting contents of the main 16 items can be set by using two displays. It can be set by the method of substituting numerical value.For the setting contents, refer to the following table.

20mA

4

Zero adjustment

mA

INPUT INPUT INPUT

20mA

4

Span adjustment

mASingle deflection

0

mADouble deflection

0


50 steps can be set. (about 0.3mA )

Set the zero adjustment for CH1.

50 steps can be set. (about 0.3mA )

Set the span adjustment for CH1.

According to the set-up diagram (page 6), save thechanged contents, or continue to the other set-up menu.


Pulse output elementImported active energy (Pulse output 1)Exported active energyImported lag reactive energy (Pulse output 2)Imported lead reactive energyExported lag reactive energyExported lead reactive energyNo output

Display Wh

Wh varh (LAG) varh (LEAD)

varh (LAG) varh (LEAD) non

Digital display Settable pulse value [kW/pulse]18888.88

88888.88888888888.8888888.8888888

10100

110

100

0.11

100.11

10

0.010.11

0.010.11

0.0010.010.1

0.0010.010.1

kWh/PulsekWh/PulsekWh/PulseMWh/PulseMWh/PulseMWh/Pulse

Total load [kW]1 or higher and below 10

10 or higher and below 100100 or higher and below 1000


100000 or higher

12


15/32

4:115V5:120V

1:100V2:110V3:220V

VT primary current

[Exponent value]

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

DISPLAY

DISPLAYDISPLAY

PHASE

SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

Phase wire1:3P3W (2CT)2:3P3W (3CT)3:3P4W

Display pattern Using VT Direct voltage00:P00 11:P1101:P01 12:P1202:P02 13:P1303:P0304:P0405:P0506:P0607:P0708:P0809:P0910:P10

Simplified Set-up Contents List

/direct input0:direct input1:using VT

[3P4W]1:110V/63.5V2:173V/100V3:190V/110V4:380V/220V5:415V/240V6:440V/254V7:480V/277V[3P3W]1:110V2:220V

[3P4W]1:63.5V2:100V3:110V

[3P3W]


Phase wire

Display pattern

Direct voltage

Using VT /direct input

Set-up menu


VT primary voltage

For 1 secend or more+

Set the set-up menu number to End.Press PHASE and DISPLAY simultaneously for 1 secondor more.

Set the phase wire.

1 : 3P3W 2CT 2 : 3P3W 3CT

3 : 3P4W

00 : P00 to

13 : P13

Set the display pattern.

0 : direct input.1 : using VT

Set using VT or direct input (without VT).

[3P3W]1 : 110V2 : 220V

[3P4W]

Set the rated voltage scaling for the bar graph.If you set 1: using VT on set up No. , this contentcannot be set.

Set the secondary voltage values of VT.

cannot be set.If you set 0: direct input on set up No. , this content

[3P3W]1 : 100V2 : 110V3 : 220V

[3P4W]1 : 63.5V2 : 100V3 : 110V

4 : 115V5 : 120V Set the primary voltage values of VT.

If you set 0: direct input on set up No. , this contentcannot be setIt is set by the top 3 digits voltage values and the exponentvalues (10 to the n-th power).The set-up order is the exponent values and the voltage values.

Exponent values: 0 (10 0 = 1 time)1 (10 1 = 10 times)2 (10 2 = 100 times)3 (10 3 = 1000 times)

Voltage values: the top 3 digits (0 to 9)Example: Set-up to 10000V

Exponent values: 2Voltage values: 100

Simplified Set-upSET RESET

PHASEIn the operation mode, press and simultaneously for 2 seconds or more, and the following operation becomes available.By pressing in the simplified set-up mode, the simplified setting page is changed.


00:0s 10:5min01:10s 11:6min02:20s 12:7min03:30s 13:8min04:40s 14:9min05:50s 15:10min06:1min 16:15min07:2min 17:20min08:3min 18:25min09:4min 19:30min

CT primary current

[Exponent value]0:5.0 to 9.9A1:10 to 99A2:100 to 990A3:1000 to 9900A4:10000 to 30000A

[Current value](10 digits) (1 digit) 0 to 9 0 to 9

Communicationmethod

1:CC-Link 2:ModBus

ModBusbaud rates

1:2400bps2:4800bps3:9600bps4:19.2kbps5:38.4kbps

ModBusaddress

001 to 255

ModBus parity0:non1:odd2:EVEn

ModBusstop bit

1:12:2


01 to 64


0:OFF1:ON

CC-Link Baud rates

1:156kbps2:625kbps3:2.5Mbps4:5Mbps5:10Mbps

0:60 to 999V1:1000 to 9990V2:10000 to 99900V3:100000 to 750000V

[Voltage value](100 digits) (10 digits) (1 digit) 0 to 9 0 to 9 0 to 9

1 : 100/63.5V2 : 173/100V3 : 190/110V4 : 380/220V

5 : 415/240V6 : 440/254V7 : 480/277V

13


16/32

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,00: 0s01: 10s02: 20s03: 30s04: 40s

05: 50s06: 1min07: 2min08: 3min09: 4min

10: 5min11: 6min12: 7min13: 8min14: 9min

15: 10min16: 15min17: 20min18: 25min19: 30min

(Page change ofset-up display)

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

DISPLAY SET

PHASE

MAX/MIN

SET

F unction s

Time constant forcurrent demand

CT primary current

Set the primary current values of CT.It is set by the top 2 digits current values and the exponentvalues (10 to the (n-1)th power).The set-up order is the exponent values and the current values.

Exponent values : 0 (10 -1 = 0.1 time)1 (10 0 = 1 time)2 (10 1 = 10 times)

3 (102

= 100 times)4 (10 3 = 1000 times)

Current values:the top 2 digits(0 to 9)

Example: Set-up to 50A

Exponent values: 1 Current values: 50 Set the time constant for calculating current demand.

Communicationmethod

ModBus address

ModBus parity

ModBus stop bit

CC-Linkstation number

CC-Link baud lates

ModBus baud rates

Set-up menu


0: OFF1: ON

Set the communication module reset.In case of ModBus, this content cannot be set.

Set it ON.

According to the set-up diagram (page 6), save the changed contents,or continue to the other set-up menu.

Set the CC-Link baud rate.In case of ModBus, this content cannot be set.

1: 156kbps2: 625kbps3: 2.5Mbps

4: 5Mbps5: 10Mbps

Set the ModBus stop bit.In case of CC-Link, this content cannot be set.

1: 12: 2

Set the ModBus baud rate.In case of CC-Link, this content cannot be set.

1: 2400bps2: 4800bps3: 9600bps

4: 19.2kbps5: 38.4kbps

Set the communication method.This is set only if the type of ME96NSR-MB has theCC-Link optional plug-in module. In case of theother combination, this content cannot be set.1: CC-Link2: ModBus Set the ModBus address number.

In case of CC-Link, this content cannot be set.

Address: 001 to 255

Set the ModBus parity.In case of CC-Link, this content cannot be set.

0: non1: odd2: even

Set the CC-Link station number.In case of ModBus, this content cannot be set.

Address: 01 to 64

It is possible to display the type of the optional plug-in module when the optional plug-in module is mounted.In the operation mode, after pressing and simultaneously for 2 seconds or more, the following operation becomes available.

Display of the Type of Optional Plug-in Module

SET RESET

Set-up menu

Set-up menu

1 secend or more+

Display the type of theoptional plug-in module

Set the set-up menu number to End.

According to the set-up diagram (page 6), end the display of the type ofoptional plug-in module or continue to the other set-up menu.

Displays the type of the optional plug-in module.

non : No optional plug-in module4201 : ME-4201-NS960052 : ME-0052-NS960040C: ME-0040C-NS96


Note Even in the set value confirmation mode, the type of the optional plug-in module can be displayed. The procedure is the same as the above-mentioned.

14


17/32

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

SET

SET

SET

SET

SET

SET

SET

Set the test menu number to 1.

Test the alarm output.When , is pressed, the display and the contact output are changed as follows.+

When , is pressed, the display and the analog output CH1 are changed as follows.+

oFF(Opened)

on(Closed)

To test the other outputs, continue the test according to the procedures in page 15 to page 16.When the test is finished, turn off the power supply.

When the ME-4201-NS96 optional plug-in module is installed, simulated signal output to test the alarm output circuit can be put out. Alarm Output Test

The following operation becomes possible when you turn on the power supply while pressing at the state of power failure.It is not possible to test without the optional plug-in module.

Test menu

Test menu

Alarm output test

at the state of power failure.

When the ME-4201-NS96 optional plug-in module is installed, simulated signal output to test the analog output circuit can be put out. Analog Output Test

The following operation becomes possible when you turn on the power supply while pressingIt is not possible to test without the optional plug-in module.

Test menu

Test menu

Analog outputCH1 test





Test the analog output CH1.

50% output 100% output0% output

Test the analog output CH2.When , is pressed, the display and the analog output CH2 are changed as follows.+






To test the other outputs, continue the test according to the procedures in page 15 to page 16.

When the test is finished, turn off the power supply.

Test Function

DISPLAY

DISPLAY

15


18/32

F un ctions

Test menu

Test menu

Pulse outputCH1 test

Pulse outputCH2 test

Test menu

Test menu

Digital outputCH1 test

Digital outputCH2 test



When , is pressed, the display and the pulse output are changed as follows.



The initial value of each CH of this test mode is Open.If CH is changed or this test mode ends, the output becomes Open.

+

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

+ ,

When the ME-4201-NS96 optional plug-in module is installed, simulated signal output to test the pulse output circuit can be put out.


Pulse Output Test

SET

SET

SET

SET

SET

SET

Digital Output Test

Note

DISPLAY

When the ME-0052-NS96 optional plug-in module is installed, simulated signal output to test the digital output circuit can be put out.


DISPLAY

oFF(Opened)

on(Closed)

When , is pressed, the display and the pulse output are changed as follows.+

oFF(Opened)

on(Closed)

When , is pressed, the display and the contact output are changed as follows.+

oFF(Opened)

on(Closed)

When , is pressed, the display and the contact output are changed as follows.+

oFF(Opened)

on(Closed)

Test the digital output CH1.

Test the digital output CH1.

Test the pulse output CH1.

Test the pulse output CH2.

Test Function (Continued)

16


19/32

DISPLAY DISPLAY DISPLAY DISPLAY

First display

Current average valuePower (total)Voltage average value

Example of display of upperstage element on bar graph

Example of display ofpower factor on bar graph

Current phase 1Power (total)Voltage phase 1-2



Second display Third display Fourth display Display number

This shows that second display ofthe four displays is being displayed.

Note 2: Even in the maximum and minimum value display, when the DISPLAY is pressed, the display will switch over.

Note 1: When the display is changed by pressing DISPLAY ,the following display is displayed just for a few seconds.

Note: When PHASE is pressed, the phase will switch over, even in the maximum and minimum value display.

PHASEPHASEPHASEPHASE

PF var WAAVGV(L-L) AVG Hz

PF var WAAVGV(L-L) AVGV(L-N) AVG Hz

PF var WAAVGV(L-L) AVG Hz

PF var WAAVGV(L-L) AVGV(L-N) AVG Hz

By pressing DISPLAY , the measurement display switches over.

By pressing PHASE , the current phase and the voltage phase switches over.

Measurement item to be displayed on bar graph can be selected. By displaying one item by a bar graph and other three items by digital numbers,four elements can be displayed at once.

In the bar graph, measurement elements shown by or are displayed. As for voltage, current, active power, reactive power, power factor, andfrequency, they can be displayed on the bar graph even if they are not set on display pattern.

Press or to select measurement elements to be displayed on the bar graph.

AVG (or ) of display measuring items

AVG (or ) of displaymeasuring items

Upper Lower Middle

Lower MiddleUpper

Display change example (Display pattern: P01, Phase wire: Three phase 4 wire)

Display Change

+

Operation

Phase Change

Bar Graph Display

Display change example (Phase wire: Three phase 3 wire)

The display element in the bar graph changes as follows by the display pattern that has been selected.(i) When digital tri-level display are the same items

[Three-phase 3 wire ]


(ii) When the measuring items are all different[Three-phase 3 wire ]


Explanation of Bar Graph

Selection of Bar Graph

Reference Display items and sequences vary with display patterns (P01 to P13) and additional display. For detailed display pattern, refer to page 22.

17


20/32

F un ctions

Display change example (Display pattern : P01)

Update of Delay Time

Cyclic Display

Phase Cyclic Display

When MAX/MIN is pressed, the display changes into maximum value and minimum value display. And when MAX/MIN is pressed, the displaychanges back to the present value display.

When RESET is pressed for 2 seconds or more, the displayed maximum value and minimum value can be reset.(The maximum/minimum value and the present value become the same.)

Reset of Maximum Value and Minimum Value

When RESET and are pressed simultaneously for 2 seconds or more, all the maximum values and minimum values are reset.

If maximum/minimum values do not continue for a long time since delay time, it is not updated. (Delay time is set by set-up menu 5.)Please set the delay time when you do not want to make the maximum value updated in the condition of excessive value in short time such asstarting currents of the motor.

In cyclic display, display and phases automatically change every 5 seconds.

When DISPLAY is pressed for 2 seconds, the cyclic display screen appears.Cyclic display is possible even on the maximum value and minimum value display.

When PHASE is pressed for 2 seconds, the phase cyclic display screen appears.Phase cyclic display is possible even on the maximum value and minimum value display.

Note 1: Before shifting to the cyclic display screen, the display blinks 3times.Note 2: By pressing any key other than the SET , it goes back to manual

display change.Note 3: In the cyclic display, display number is not displayed.

Note 1: Before shifting t o the cyclic display screen, the display blinks 3times.

Note 2: By pressing any key other than the SET , it goes back to manualdisplay change.

Display of maximum value and minimum value

Note 1: In the maximum value and minimum value display, bar graph is lit only between the maximum value and the minimum value.Note 2: When the screen shifts to the maximum value and minimum value display, the following are displayed in the order below. A AN DA DAN V W var VA PF Hz HI HI N HV However, item that are not set for display are not displayed.Note 3: For harmonics, only the following maximum values are displayed. Harmonic current total effective value, 1st, 3rd, 5th, 7th, 9th, 11th, 13th current effective values Harmonic voltage total distortion ratio, 1st voltage effective value, 3rd, 5th, 7th, 9th, 11th, 13th containing ratio

Note 1: The maximum values and minimum values n ot displayed are not reset.Note 2: All degrees are reset for harmonics.

Note 1: When delay time is set, the value whose value of middle stage is larger than the maximum value might be displayed until delay time passes.Note 2: The demand current, harmonics current, and harmonics voltage are not delayed, so the current and voltage may display larger value than the present value.

Cyclic Display

The maximum values and the minimum values can be displayed. Maximum Value and Minimum Value Display

+

MAX/MIN MAX/MIN

RESET

Press for 2 seconds.

DISPLAY

Display for 5 seconds Display for 5 seconds Display for 5 seconds Display for 5 seconds

Press for 2 seconds.

PHASE

Maximum value andminimum value display

Present value display

Operation (Continued)

Display for 5 seconds Display for 5 seconds Display for 5 seconds Display for 5 seconds

18


21/32

Note 1: In alarm condition, the digital value, the unit (A, V, W, var, VA, PF, Hz), and the phase (1, 2, 3, N, AVG, , DM) of the measurement items blink. There is no blinking when the item is not on the display.Note 2: In alarm hold condition, the unit (A, V, W, var, VA, PF, Hz) and the phase (1, 2, 3, N, AVG, , DM) of the measurement items blink. There is no blinking when the element is not on the display.Note 3: Only the present value (middle digital display) blinks on maximum and minimum value screen.

Note 4: In harmonics, only total distortion ratio and RMS value blink. The display of degree does not blink.

Note: In contact input screen, alarm reset (including all items batch reset) cannot be operated.

Set-up

If the item that had alarm set-up is displayed on the bar graph, the alarm indicator appears.By blinking of , upper or lower limit is shown.

Alarm Indicator

Refer to set-up menu 5. (see page 10)

Behavior During Alarm GenerationAlarm condition: When measurement value exceeds alarm value, display blinks and alarm contact closes.Alarm cancel: When alarm is canceled, display blinks normally and alarm contact opens.

Alarm Cancel MethodTiming of alarm cancel differs by alarm cancel method.

When alarm delay time is set, alarm is not generated until status of measurement value exceeding upper/lower setting value continues for delay time.

Alarm Delay

Generation and Cancel of Upper/Lower Limit Alarm

Phase that judge upper/lower limit alarm differs by measuring items. Please refer to the following table.

When the value exceeds the upper or lower limit setting value set in advance, the display blinks and alarm can be output.(No alarm output when all of the input voltage/input current is zero)

After the measurement value falls below the upper value or exceeds the lower setting value, alarm is maintained. When the item thatgenerates the alarm is displayed, and button is pressed, the alarm resets.When button is pressed for two seconds or more, all items of alarm are reset.

Alarm Cancel MethodMeasurement value > Upper limit value(or Measurement value < Lower limit value)

Measurement value < Upper limit value(or Measurement value > Lower limit value)

Normal display

Normal display

ClosedAlarm contact

Alarm contact

Display

Display

Automatic(Auto)

Manual(HoLd)

Closed Closed

(Alarm retention)

Opened

Opened

ALARM , HI or LO : blink

ALARM , HI or LO : blink ALARM , HI or LO : appear

Automatic(Auto)

Manual(HoLd)

When the measurement value falls below the upper setting value or exceeds the lower setting value, alarm automatically resets.

A upper limitA lower limit

AN upper limit (*2)Demand A upper limitDemand A lower limit

Demand A N upper limit (*2)V(L-N) upper limitV(L-N) lower limitV(L-L) upper limitV(L-L) lower limit


var upper limitvar lower limitPF upper limitPF lower limitHz upper limit

Hz lower limitHarmonic currenttotal RMS value

Harmonic currentphase N RMS value (*2)

Harmonic voltagetotal distortion ratio

Alarm item (*1)3P3W/3P4W3P3W/3P4W

3P4W3P3W/3P4W3P3W/3P4W

3P4W3P4W3P4W

3P3W/3P4W3P3W/3P4W3P3W/3P4W3P3W/3P4W3P3W/3P4W3P3W/3P4W3P3W/3P4W3P3W/3P4W3P3W/3P4W

3P3W/3P4W3P3W3P4W

3P4W

3P3W3P4W

PhasesPhase 2 Phase 3 Phase N Phase 1-2 Phase 2-3 Phase 3-1 AVG/

*1: The apparent power is not included in the alarm element.*2: Phase N is a alarm element to be independent.

Phase wire Phase 1

RESETRESET

RESET

19


22/32

When and are pressed, harmonic degree changes. When PHASE is pressed, harmonic phase changes.

Measuring Items

Degree Change Method

Harmonic Display Examples

RMSvalue

Distortionratio

Note: When a fundamental harmonic is 0, the distortion ratio display 0%.

Harmonics DisplayHarmonic RMS value, distortion ratio, and content rate can be displayed.

F un ctions

Note: Harmonic total is shown by ALL.

* When used as 3P3W, transition is only for 1-2 phase, 2-3 phase.


+

Example of harmoniccurrent total display

Example of harmonicvoltage 5th display( ) ( )

DegreeCurrent ( other than phase N)

Harmonic total1st3rd5th7th9th

11th13th

RMSvalue

Distortionratio

Current (phase N)RMSvalue

Distortionratio

VoltageRMSvalue

Distortionratio

Harmonic current(phase N)

+ ,

+ ,

+ ,

DISPLAY

+ ,

+ ,

DISPLAY

PHASEPHASE

PHASE

PHASEPHASE

PHASE

+ ,

PHASEPHASE

PHASE

PHASE PHASE

PHASE

DISPLAY

+ ,

+ ,

PHASEPHASE

PHASE

PHASEPHASE

PHASE

+ ,

PHASEPHASE

PHASE

PHASEPHASE

PHASE

DISPLAY

Current total phase 3 Distortion ratio/RMS

Current 1st phase 3 RMS

Current totalphase N RMS

Current 1stphase N RMS

Current 3rdphase N RMS

Current 13thphase N RMS

Current 13th phase 3 Distortion ratio/RMS

Current 3rd phase 3 Distortion ratio/RMS

Voltage total phase 3-N Distortion ratio/RMS

Voltage 1st phase 3-N RMS

Voltage 3rd phase 3-N Distortion ratio/RMS

Voltage 13th phase 3-N Distortion ratio/RMS

Harmonic current

Harmonic voltage

Previousdisplay

Nextdisplay

















20


23/32

There are Auto reset method and Latch method for digital input reset method.When set on the latch method, the input status is continued until the latch canceling operation.For example, when the alarm contact is input and the alarm is stopped, you cannot miss the alarm because the alarm generated status is continued inthe basic device.

When SET , RESET , and PHASE are pressed simultaneously for 2 seconds, the measured values of active energy (Wh) and reactive energy(varh) are reset. (This is effective only in the present value display.)

As same as in the set-up diagram (page 6), select the set-up menu number to confirm,and press SET .The way to get back into the operation mode is same as in the set-up diagram.However, the simplified set-up menu canot be confirmed in the setting value confirmationmode.

In the operation mode, press SET for 2 seconds.

1 In the operation mode, press DISPLAY and digital input (d.in) screen is displayed.2 In the digital input screen, the latch is canceled by pressing RESET for 2 seconds.

Reset Method of Digital Input

Canceling of the Latch

Going into Setting Value Confirmation Mode

Setting Value Confirmation

Note: All of active energy (Wh) and reactive energy (varh) not displayed are also reset.

8888. 88

88888. 8888888

8888. 8888888. 8888888

k

M

1000 = 3 Three-phase 4-wire type

(Primary voltage value: phase to neutral)

(Primary voltage value: phase to phase)3 Three-phase 3-wire type

Enlarged 3 Digital FiguresWhen and are pressed simultaneously for 2 seconds, values of active energy and reactive energy are enlarged by 3 figures.

Active energy and reactive energy are displayed on the lower stage.Display type is shown in the right table according to total load power.

Expanded Counting DisplayMeasured value display and enlarged 3 digital figures display of active energy and reactive energy can be displayed. Display of Active Energy and Reactive Energy Display

Wh and varh Reset

Example of Display

Display of Digital Input and Digital OutputDisplays the digital input and digital output state.When the type ME-0052-NS96 or ME-0040C-NS96 optional plug-in module is not installed, this operation cannot be done. Display of Digital Input and Digital Output

Note: To display digital input screen, it is needed to set display of the digital input/output on on. The initial setting is set on on.

When confirming the setting value, use the setting value confirmation mode.In this mode, the contents of the set-up items cannot be set, which prevents changing other set values by mistake during operation.

Setting Value Confirmation Mode

Total load [kW] =

In the case of reactive power, kW in the right table is exchanged intokvar, and kWh into kvarh.

(Primary voltage value) (Primary current value)

Note: This function is made only on active energy and reactive energy display.Example: When 3 digital figures are enlarged on active energy screen, reactive energy is not enlarged.

In order to enlarge digital figures of reactive energy, display reactive energy on the screen andoperate the same way.

Exported active energy

(Example of d ig ital input disp lay) (Example of d ig ital output disp lay)

Imported lead reactive energy Exported lag reactive energy Exported lead reactive energy

Total load [kW]1 or higher and below 10



100000 or higher

Digital display Unit (k/M)

,Pressing

simultaneouslyfor 2 seconds

(Set-up mode) (Set value confirmation mode)

+

blink extinction

ItemsQuadrant

Unsigned

Unsigned

LAG Display*Unsigned

A, DA, V, VAHz, HI, HV

W

var, PF

Unsigned

Unsigned

LEAD Display* sign

Unsigned

sign

LAG Display*Unsigned

1 2 3 4

Unsigned

sign

LEAD Display* sign

* When displaying var or PF by bar graph, LEAD/LAG display is lit.

-var

+var

- W +W

Quadrant 2Quadrant 3

Quadrant 1Quadrant 4

The polar display of each measuringitems are as follows.

Polar Display of Each Measuring Items

+

21


24/32

Display Patten Contents


F un ctionsWhen the display elements are set in the set-up menu 1 and the set-up menu 4, by pressing DISPLAY , the display transits from No.1 in the order shown in the following table.Three phase 4-wire

P01

P02

P03

P04

P05

P06

P07

P08

P09

P10

P11

P12

P13

P00

UpperMiddleLowerUpperMiddleLowerUpperMiddleLowerUpperMiddleLowerUpperMiddleLowerUpperMiddleLowerUpperMiddleLower


AWVAV

WhA

PFVAV

WhPFWvarA1A2A3AVW

AV

WhA

DAVA

DAVA

DAWh

ADAWh

AWPFAW

WhA

PFWAW

WhHzW

var

AW

Wh

ADAWAV

WhAW

Wh

APFVA

PFWhA

PFvarA

varvarhVAWvarA

V

AV

Wh

A

A

APFVAA

VAWh

A ANA

AN

DAV

Wh

APFHzA

PFWh

A ANA

AN

A ANWV

Wh

A ANA

HzWh

DA

DA NA

ANDA

DA NA

AN

A AN

DA

DA N

DA

DA NV

HzWh

VHz

varh

A AN

NO.1 NO.2 NO.3 NO.4 NO.5NO.6NO.7NO.8 NO.9 Exportedactive energy

Exportedactive energy


Importedlead reactive energy

Exportedlag reactive energy

Exportedlead reactive energy













Exported

active energy















Imported

lead reactive energy

Exported

lag reactive energy

Exported

lead reactive energy





Harmonic phase N current

Degree

RMS value

DegreeRatio

RMS value

diDI No.State

doDO No.

Statedi

DI No.State

doDO No.

Statedi

DI No.State

doDO No.

Statedi

DI No.State

doDO No.

State

diDI No.State

doDO No.

Statedi

DI No.State

doDO No.

State

diDI No.State

doDO No.

Statedi

DI No.State

doDO No.

Statedi

DI No.State

doDO No.

State

diDI No.State

doDO No.

Statedi

DI No.State

doDO No.

Statedi

DI No.State

doDO No.

Statedi

DI No.State

doDO No.

Statedi

DI No.State

doDO No.

State

DegreeRatio

RMS valueDegree

RMS value

DegreeRatio

RMS value

DegreeRatio

RMS valueDegree

RMS value

DegreeRatio

RMS value

DegreeRatio

RMS value

Degree

RMS value

DegreeRatio

RMS value

DegreeRatio

RMS valueDegree

RMS value

DegreeRatio

RMS value

DegreeRatio

RMS valueDegree

RMS value

DegreeRatio

RMS value

DegreeRatio

RMS value

Degree

RMS value

DegreeRatio

RMS value

DegreeRatio

RMS valueDegree

RMS value

DegreeRatio

RMS value

DegreeRatio

RMS valueDegree

RMS value

DegreeRatio

RMS value

DegreeRatio

RMS valueDegree

RMS value

DegreeRatio

RMS value

DegreeRatio

RMS valueDegree

RMS value

DegreeRatio

RMS value

DegreeRatio

RMS value

Degree

RMS value

DegreeRatio

RMS value

DegreeRatio

RMS value

Degree

RMS value

DegreeRatio

RMS value

DegreeRatio

RMS valueDegree

RMS value

DegreeRatio

RMS value

DegreeRatio

RMS value

Harmonic current

Additional screen (displays when Set-up Menu 4 i s set)NO.10 NO.11 NO.12 NO.13 NO.14 NO.15

Harmonic voltageNO.16

Digital input stateNO.17

Digital output stateNO.18

Screen set on display pattern

P01

P02

P03

P04

P05

P06

P07

P08

P09

P10

P11

P12

P13

P00

UpperMiddleLowerUpperMiddleLowerUpperMiddleLowerUpperMiddleLower


UpperMiddleLowerUpperMiddleLowerUpperMiddleLower

A W

VAV

WhA

VAV

Wh

W

AVWAV

WhA

DAVA

DAVA

DAWh

ADAWh

A W

A WWh

A

WA

WWh

Hz W

A WWh

ADA W

AV

Wh

A WWh

A PF

VA

WhA

A

varh

A V

AV

Wh W

A

HzA

Wh

DAV

WhV

HzWh

AHzWh

WV

WhV

Hzvarh

NO.1 NO.2 NO.3 NO.4 NO.5 NO.6Harmonic voltage

DegreeRatio

RMS valueDegreeRatio



RMS value

DegreeRatioRMS value

DegreeRatio






RMS value

DegreeRatio



RMS value

diDI No.State

doDO No.

Statedi

DI No.State

doDO No.

Statedi

DI No.State

doDO No.

Statedi

DI No.State

doDO No.

State

diDI No.State

doDO No.

Statedi

DI No.State

doDO No.

State

diDI No.State

doDO No.State

diDI No.State

doDO No.

Statedi

DI No.State

doDO No.

Statedi

DI No.State

doDO No.

Statedi

DI No.State

doDO No.

Statedi

DI No.State

doDO No.

Statedi

DI No.State

doDO No.

State

diDI No.State

doDO No.

State

Harmonic current

Additional screen (displays when Set-up Menu 4 i s set)NO.7

Digital input stateNO.13

Digital output stateNO.14

Screen set on display pattern

Three phase 3-wire

V3NV2NV1N

V3NV2NV1NA1

A2A3

A1A2A3 V 3N

V2NV1N

A1A2A3

A1A2A3

V3NV2NV1N

V3NV2NV1N

V3NV2NV1N

DA 1DA 2DA 3

DA 1DA 2DA 3

DA 1DA 2DA 3

V3NV2NV1NA1

A2A3

VA 1VA 2VA 3

PF 1PF 2PF 3

W 1W 2W 3

var 1var 2var 2

PF PF PF PF

PF

PF

PF

PF

AN

AN

var

var

var var

varV23V31

V12A1A2A3

V23V31

V12

DA 1DA 2DA 3

DA 1DA 2DA 3

DA 1DA 2DA 3

V12V23V31

V12V23V31

A1A2A3

A1A2A3

V12V23V31

A1A2A3

V12V23V31

V12V23V31

A1A2A3

A1A2A3

PF

NO.8 NO.9 NO.10 NO.11 NO.12

DegreeRatio




RMS value

DegreeRatioRMS value

DegreeRatio






RMS value

DegreeRatio



RMS value

Displaypattern

Displaypattern

Digitaldisplay

Digitaldisplay

Wh: Imported active energy, varh: Imported reactive energyNote: When an additional screen is added, a screen number is added.

W: Total active power, var: Total active power, PF: Total power factor

Arbitrarymeasuring item

For details, refer tothe users manual

Arbitrary measuring item For details, refer tothe users manual

22


25/32

Dimensions

Dimensions / Mounting / Wiring,RSN69EM BM-RSN69EM

Option cover

(With the optional plug-in module)

( 1 0 6

. 9 )

8 6

. 2

2 0

. 7

Optional Plug-in Module

7 5

. 8 6 1

. 3

46.8

81.2 25.2

17.1

88.8

Mounting1 Dimensions of Panel

92 + 0.50

9 2 +

0 . 5

0

2 View Angle

3 Attachment

Protective sheet

Attachment position

In the case to attaching to the end of the panel, check the wiring work space and decide the attachment position.

Optional Plug-in module

4 Installing the Optional Plug-in Module

Please do not tighten too stronglyto prevent panel and screw frombreaking.Tightening torque for this product:0.3Nm to 0.5Nm(Half the torque applied normallyfor this type of screw)Also, please tighten the upper andlower screws at the same time.

A protective sheet is attached to the display for protection against scratch during the attachment to panel. Before using, remove the protective sheet.When you remove it, the display may light up due to generation of static electricity, but it is not an error. It goes off by natural discharge after a while.

The contrast of the display changes at view angles.Mount it at the position that is easy to see.

The panel hole dimensions are shown below.It can be attached to a panel with thickness of 1.6 to 4.0mm.

For attachment of the basic device into the panel hole, attach according to the following procedure.

Install the optional plug-in module after the power is turned off.The option is not recognized when installed while power is on.In this case, the option is recognized by power suspension/power resumption or restarting the basic device.

Combine the slot of the basic device and theconvex part of the optional plug-in module.

9 1

. 6 ( P A

N E L C U T )

9 5

. 8 ( C O V E R )

95.8 (COVER)

91.6 (PANEL CUT)

Note

Note

The attachment lug is installed in two holesof the top and bottom of the basic device.

Tighten the screws of the lug, and fix onto the panel.

When installing the optional plug-in module onto the basic device, install according to the following procedure.The option cover is removed. The optional plug-in module is installed.

View angle

6 0

10

60

6 0 Viewed from

the topViewed from

the side

23


26/32

Wiring

Wiring Diagram

1 Applicable Cable Size

The table on the right describes the applicablewire size. Applicable wire size

Tightening torqueStrip Gauge

Input and output terminals of the basic deviceAWG24 to 14

0.4Nm10mm

Terminals of the optional plug-in module

10mm

2 Wiring Input and Output Terminals of the Basic DeviceStrip top of the cable or crimp the ferrule.Slacken screws of the terminal block, and insert the cables into

terminal hole.Tighten the terminal screws according to the tightening torque

mentioned above.

Terminals of the Optional Plug-in ModuleStrip top of the cable or

crimp the ferrule.

Insert the cables bypushing the lever, andconnect by releasingthe lever.

Insert hole Lever

3 Confirmations

After wiring, make sure the following:M The wires are connected correctly.M There is no mistake in wiring.

AWG 24 to 14 When using a stranded wire, use a ferrule. (AWG 16)

Dimensions / Mounting / Wiring

Three phase 4-wire type : Example of ME96NSR (with VT) Three phase 4-wire type : Example of ME96NSR-MB (for direct input)

+C1

PN

P3

P2

P1

C3

+C3

C2

+C2

C1

T+

MA

NC

MB

NC

SLD

SLD

Ter

T

ProtectiveEarthing

Load

(+)()

RS485(ModBus)

RS485(ModBus)

kKL

1 2 3 0

KL

l k

lKL

k

l

RS485(ModBus)

+C1

PN

P3

P2

P1

C3

+C3

C2

+C2

C1

NC

MA

NC

MB

NC

NC

NC

NC

NC

u

vu

vuv

UVU

VUV

kKL

1 2 3 0

Load

KL

l k

lKL

k

l

ProtectiveEarthing

(+)()

ProtectiveEarthing

Load

(+)()Load

ProtectiveEarthing

(+)()

Three phase 3-wire type : Example of ME96NSR-MB (with VT, wiring 2CT)

Three phase 3-wire type : Example of ME96NSR (for direct input, wiring 3CT)

UV

u

vu

v

UV

kKL

l

KL

k

l

+C1

P2

P3

NC

P1

C3

+C3

C2

+C2

C1

T+

MA

NC

MB

NC

SLD

SLD

Ter

T

kKL

l

kKL

1 2 31 2 3

l

KL

k

l

+C1

P2

P3

NC

P1

C3

+C3

C2

+C2

C1

NC

MA

NC

MB

NC

NC

NC

NC

NC

Auxiliary power supply100 to 240VAC 100 to 240VDC

1 For a low voltage circuit,grounding of the secondarysides of VT and CT in notnecessary.

2 Do not connect to NC terminal.

Auxiliary power supply100 to 240VAC 100 to 240VDC

1 For a low voltage circuit,grounding of the secondary

sides of VT and CT in notnecessary.2 Do not connect to NC terminal.

1. If the polarity of VT and CT is not correct, it cannot be measured correctly.2. In case of DC auxiliary power, it should be wired correctly because it has polarity. In case of AC auxiliary power, it does not have polarity.3. For a low voltage circuit, grounding of the secondary sides of VT and CT is not necessary.4. Always earth the terminal to the protective earth conductor. Earth the terminal with under 100 ohm of earth resistance. Otherwise, there will be a

false operation.

1. Use the shielded twisted pair cable.2. To the units of both the end of ModBus link, the 120 ohm resistance has to be attached.

This instrument can perform 120 ohm termination by short-circuiting the terminal of T-and Ter.3. The earth has to be connected to earth by a thick wire of low impedance.4. Keep the distance between ModBus link to power line.5. When the setting is 2CT, the use by 3CT wiring cannot correctly measure for phase 2.

Note

Note

24


27/32

Optional Plug-in Module : ME-4201-NS96 Optional Plug-in Module : ME-0052-NS96

Note

Note

Conditions DistanceBelow 600V power lines

Other power lines

30cm or more

60cm or more

ME-4201-NS96ME96NSRCH1+CH1CH2+CH2CH3+CH3CH4+CH4C1AC1BC2AC2BA

COM

Analog output CH1

Analog output CH2

Analog output CH3Analog output CH4

Pulse output1

Pulse output2

{ {

{ { { { {Alarm output

DI1,DI2,DI3,DI4,DI5are connected inside.

ME-0052-NS96ME96NSR-MBDI1+DI1DI2+DI2DI3+

DI3DI4+DI4DI5+DI5DO1+DO1DO2+DO2

24VDC

DO1

DO2

{ {

C RR

DI1+

DI1

DI5+DI5

Optional Plug-in Module : ME-0040C-NS96

ME-0040C-NS96ME96NSR

C RR

24VDC

DI1

DI4COM

C RR

DI2

DA

DB

DG

SLD

FG

SLD

DG

DB

DA

DI1

DI2

DI3DI4

COM

ProtectiveEarthing

CC-LinkCommunication

CC-LinkCommunication

+C1

PN

P3

P2

P1

C3

+C3

C2

+C2

C1

NC

MA

NC

MB

NC

NC

NC

NC

NC

1. Do not bunch the digital input/output signal cables with the main circuit or power cables, or install them close to each other. Keep the distance betweenthe digital input/output signal cables, the main circuit or power cables, and high voltage lines shown below, when they run parallel to each other.

1. As for CC-Link cable, use the designated cable. Each of Ver.1.10 compatible CC-Link cables, CC-Link specified cables, and CC-Link specifiedhigh-performance cables cannot be used together with other cable types. If used together, correct data transmission will not be guaranteed.The terminating resistor is different depending on the applied cable.

2. Connect the shielded wire of the CC-Link specified cable to SLD of each module, and earth the both ends of the shielded wire FG. The SLD and FGare connected into the module.

3. Keep the distance between CC-Link cables to power lines (At least 10cm). When connecting long distance in parallel, please set apart more than 30cm.4. Fill the requirements of total wire distance, station distance, and terminal resistance value according to baud rate and type of cable. (As for detail of the

requirements, refer to the operation manual for CC-Link master unit.)5. To the units of both the end of CC-Link line, the terminal resistors should be attached. And the terminal resistors should be attached in between DA andDB.

2. Analog output signal cables should keep the distance from the other power cables and input signal (VT, CT and auxiliary power) cables, and should not

be bunched. And use the shielded cables or twisted pair cables so that it is not affected noise, serge, and induction.Also, the wiring cables should be as short as possible.

3. In case of ME96NSR-MB with ME-4201-NS96, the ModBus interface and the analog outputs do not have the insulation between them.

Wiring Diagram (Continued)

25


28/32


29/32

Transmission

Twist Pair Cable SpecificationsPart of recommended cables of twist pair cables to be used in CC-Link are introduced below.As for details, refer to Mitsubishi Electric Open Field Network CC-Link.CC-Link performance is not guaranteed with other than the recommended cables.

ModBus Specifications

SpecificationsItemRS485, 2 wires half duplexModBus RTU

2400, 4800, 9600, 19200, 38400bps1000m1 to 255 (FFh)31120 1/2WShielded twisted pair, AWG26 (or wider) gauge

InterfaceProtocol

SpeedDistanceAddressStation NumberTerminal ResistanceRecommended Cables

CC-Link Specifications

SpecificationsItem

1 StationRemote device station (I/O data and word data can be transmitted)

CC-Link Ver 1.1010Mbps/5Mbps/2.5Mbps/625kbps/156kbps

Numbers of Occupied Stations

CC-Link VersionBaud Rate

1 to 64Remote Station Number (Station Number)

The following conditions should be satisfied.If the system is configured by only this instrument, up to 42 units can be connected.Condition 1 : {(1 a) + (2 b) + (3 c) + (4 d)} 64

a: number of units occupied by 1 station, b: number of units occupied by 2 stationsc: number of units occupied by 3 stations, d: number of units occupied by 4 stations

Condition 2 : {(16 A) + (54 B) + (88 C)} 2304A: number of remote I/O stations, B: number of remote device stations, C: number of local stations

Maximum Number of Connected Units

Name CC-Link Exclusive Cable

FANC-SB

FA-CBL200SB, etc.

CC-Link Exclusive High Performance Cable

FANC-SBH

FA-CBL200SBH

Contact

Type

CC-Link Exclusive New Cable (CC-Link Ver.1.10)FANC-SB110H

ContactNameType

Mitsubishi Electric System & Service Co., Ltd.Kuramo Electric Co., Ltd.MITSUBISHI ELECTRIC ENGINEERING, CO., LTD.

Kuramo Electric Co., Ltd.

Notes: 1. As for terminal resistance, be sure to use 110 (1/2W) when using CC-Link exclusive cable, and 130 (1/2W) when using CC-Link exclusive highperformance cable.If other combination than the above is used, normal data transmission is not guaranteed.

2. CC-Link exclusive cable and CC-Link exclusive high performance cable cannot be used in mixture.3. System construction is eas ier by using CC-Link exclusive cable in 10Mbps and CC-Link exclusive high performance cable under 5Mbps.4. The CC-Link Exclusive New Cable is more suited for system constructed with CC-Link Ver.1.10 products.

As for details of twist pair cable, refer to CC-Link catalog CC-Link Cable Wiring Manual and MELFANS Web.

MELFANS Web : http://wwwf2.mitsubishielectric.co.jp/melfansweb/english/index.html

About ProgrammingNecessary information for operating this device by MELSEC-A/Q series sequencer loading CC-Link interface unit are as follows.In addition to this operation manual, read the following documents also. PLC I/F unit users manual Electronic Multi-Measuring Instrument programming manual (CC-Link) .................................................................................................................... LAN040503

Data Collection for ModBus Electronic Multi-Measuring Instrument ModBus I/F specification ................................................................................................................................. LSPM0075

Output Specification

Output SpecificationOutputLoad Resistance

4 to 20mADC600 max

No-voltage a contactContact Capacity: 35VDC, 0.1ARated 24VDC (19 to 30VDC), under 4mASignal Width over 30ms (with DI latch HoLd, over 30ms of pulse can be latched)

ME-0052-NS96ME-0040C-NS96

No-voltage a contactContact Capacity: 35VDC, 0.2A

ME-4201-NS96ME-0052-NS96

Optional Plug-in Module Type

Analog Output

Digital Output

Digital Input

Pulse Output

ME-4201-NS96

ME-4201-NS96

27


30/32

R ela ted Produ cts

Unit : mm

VAR-6A

Lineup of 6-Circuit and 12-Circuit Control Types Only one device is needed where many condensers are needed in 12-circuit control such as large facility orlow-voltage control.

Better Accuracy for Power Factor Measurement Accurac

Power Meter ME96NSR Catalog

Documents

Transcript of Power Meter ME96NSR Catalog