… the seed can begin.

power harrow mechanical seed drill

The Aress power harrow models possess a frame pipe, which is upstream of the tank and so the deformation stability is increased enormously. Furthermore the tank is protected from damages by this frame pipe. The poser harrows are very easy pulling.For tractors up to 95 kW (130 HP) max.

small power requirement at optimal working quality

¾ All models are equipped with p.t.o. shaft, p.t.o shaft on the rear and interchangeable gear wheel.

¾ The interchangeable gear wheel and the driving toothed wheel are working in oil – the bearing and the toothed wheel are immediately lubricated, also in cold condition.

¾ Depth adjustment of the rear levelling bar runs infinitely by spindle and depth scale.

¾ Side plates hinged

easy pulling ¾ The easy pulling of the models is due to the phase adjustment of the blades and the amount of the rotors.

¾ 12 tines at 3 m and 10 tines at 2,5 m ¾ Good mixing up and crumbling of the soil. ¾ Working without vibration ¾ Very easeful running.

Bearing ¾ The connection of the toothed wheels and rotor shaft is free from float by conical tooth system.

¾ Cover discs of the bearings protect the toothed wheels from foreign particles.

¾ Big distances of bearing are due to a solid bearing of the rotors.

¾ Stable bearing by screwed bearing carrier.

¾ Round knife holder (stone denying).

pic. Aress 3000 with crumbler packer roller

pic. Aress 2500

pic. KSE 5000 M-HK

pic. Aress

easy pulling

2 3www.regent.at

The generation of power harrows Orbit provides an optimal mixing and crumbling of the soil for the seedbed preparation on ploughed or not ploughed areas. The headstock with lateral support and the front frame make sure highest stability and protect the gear tank from deformation.The amount of the rotors and the phase adjustment of the blades enable the Orbit to be an easy pulling power harrow.

Mounting pieces hydraulically ¾ Hydr. mounting piece with 2 cylinders

Stone deflector ¾ Compact stone protection optionally available (pic.).

power harrows with exceeding technique for highest demands

¾ Gear tank made of fine grained steel with doubled thickness on the floor of the tank. Thickness of the tank at Orbit M 6 + 6 mm / Orbit S 8 + 8 mm

¾ Tooth profile cogging of the toothed wheels provides highest durability. The applied load on drive mechanism is absorbed by the convex form of the toothed wheels and the big dimensioned upper tapered rollers.

¾ The bearing case is made of one part which provides an optimal fit of bearing and shaft bearing.

¾ Big dimensioned taper roller bearing resist also lateral load. ¾ The fixing of the blades is easy to maintain by a double nut plate. ¾ The blades are arranged shuffled.

¾ Special hardened rotors and blades holder. ¾ Special labyrinth glands with support rings provide highest security (leak tightness). ¾ Blades with phase adjustment made of hardened boron steel. ¾ Dimension: 15 x 300 at mod: M 16 x 330 at mod: S

Blades fast changing system

¾ The models Orbit M and S can be equipped with the fast changing system if required.

¾ The blades are fixed with a clamping plate and interlocked with a clip pin.

¾ Blades can be changed easily and quickly.

¾ The clip pin is protected against pollution by the clamping plate.

¾ New gear drive technique with a p.to. access which is set back.

¾ Extended drive shaft – short bending – enables longer durability and absolute calm running.

¾ p.t.o. fixed drive and interchangeable gear with additional gear set in series.

Robust bearing technique – the heart of any power harrow.

Perfection in detail

4 5www.regent.at

¾ The Seedstar can be equipped with drift-shares or with the new developed double seed plates with depth control for pressure rolls.

Different rollers for an optimal seedbed preparation.

Ripple roller ø450 mm ¾ Good solidification and fine crumby earth in the area of seed deposition ensure good germination.

¾ Blockage-free working – the roller doesn’t run on the inner tube, but on the wave profile ¾ The wave profile is aligned to the seeding line. ¾ For middle to heavy soils and good for wet soils.

Packer roller Aress ø500 mm Orbit ø500 and ø550 mm

¾ Good solidification and depth lead. ¾ Low lying scraper adjustable ¾ For different types of soils, easy or weighty.

Flatten beam ¾ The deflector is available in series at all Orbit models and can be adjusted infinitely in height with spindles.

¾ The deflector can be delivered in the front optionally.

Depth adjustment ¾ The power harrow can be operated rigid in depth (roller is locked) – or it can avoid on high at unevenness irrespective of the roller in shuttling position.

¾ The dept adjustment runs with a perforated grid and socket pin.

Non-Stop version ¾ massive construction ¾ adjustable through locking bolt ¾ release force adjustable variably ¾ suitable for all soil conditions

Standard version ¾ adjustable in height through clamping plates

¾ Suitable for light soils with minimal stone portion

Track eradictors (optionally)

Crumbling packer roller ø500 mm ¾ Deep solidification due to the angled teeth. ¾ Leaves crumby surface structure ¾ Suitable for heavy loamy soils and hillside locations

With the seed machine RSM-V advantageous techniques and experiences were realized. With the compact mounting on the power harrow and the seed tank which is moved in the front the advantages in technique as weight distribution and low filling height were involved.

compact

user-friendlyprecise

6 7www.regent.at

Orb

it

Seedstar

The new double seed plates with depth control for pressure rolls ¾ A big diameter of 305 mm of the plates and the lateral pressing enable a secure drive of the double seed plate, also at light soil conditions.

¾ The seed plate pairs are staggered to each other and so avoid a blockage. To work with the Regent double seed plate is a big advantage also at crop residues or mulch seed.

¾ In combination with the depth pressure rolls it is able to achieve a precise seed deposition. ¾ The rubber pressure rolls enable an immediate close of the soil after seed deposition and so the process of germination is considerably accelerated.

¾ At a pressure of 35 kg per double seed plate it is able to work at higher speed also at changing soil conditions. Simple and tool-free adjustment of the depth of deposition per grid.

Drift-shares ¾ The drift-shares are an approved share system for all purposes for conventional cultivation of different field crops.

¾ The casting key mounted in front on the drift-share can be replaced easily in case of abrasion.

¾ The backwards mounted butterfly avoids blockages of the seed key, e.g.: rolling backwards at the headland.

The new stepless VARIO – gear ¾ This includes a 3-step-cam-lever system, which cares for highest precision at seeding.

¾ Seeding amounts from 1,5 – 300 kg can be put down steplessly and precisely on the fields.

¾ The lever of the VARIO- gear is fixed after the adjustment of the right position and can not be unfixed independently through vibrations.

A precise seed deposition is the requirement for high yield.

Exact quantity control in combination with the

new combined slanted chamber.

The new combined slanted chamber ¾ With the new combined slanted chamber with fine drilling wheel all seeds like crop, grain legumes, green manuring mixtures, clover or fine seeds as canola, phacelia, biogas millet seed, clover and poppy seed can be sowed exactly.

¾ Through the closed body of the step chambers the seed is deposited always in the same amount independent of vibrations, hillside situations or speed. The advantage is the considerably better lateral distribution per line and a better position spreading of the plants.

¾ Seed can be economized and the power of impact and the economic efficiency increased.

¾ For fine seeds the fine drilling wheel is lifted of the combined slanted chamber.

pic.: with spring pressure adjustment

fine drilling wheel

optionally: wiper backwards

optionally: cover front

an eff cient combination

Orbit and Seedstar

in drilling

8 9www.regent.at

Hydr. spurs wheel lifting ¾ Empfehlenswert bei Einsatz der Kreiselegge ohne der Sämaschine.

¾ Spornradaushebung ist mit der Scharautomatik kombiniert.

The calibration trial ¾ After adjustment of the machine according to the seed index the calibration test can easily be arranged.

¾ The monitor Seedtron does the counting and in the end you can hear a „stop“ signal.

¾ The two tanks for the calibration trial can be easily folded down and with the crank handle the calibration trial can be operated.

LED working lightstank interior space lights:

¾ For filling at poor light conditions. Rear spotlights:

¾ For the rear end during operation ¾ Lightning of the calibration trough and the seeding elements for the calibration test

¾ The working lights can be operated seperatley via the monitor Seedtron

Seedstar with wheel movement

¾ For the solo running of the Seedstar we offer a wheel movement as option.

¾ Thereby it is possible to couple the Seedstar directly on the tractor or also on the hydraulic mounting arms of the power harrow.

¾ With the wheel movement the drilling machine is universally insertable.

The monitor SeedtronThe monitor is equipped with a magnet in the back and is mounted in sight in the tractor cabin. Through the Seedtron monitor following functions can be triggered or controlled.

¾ Machine track gear shift with optional adjustable rhythms.

¾ HA-numerator with planimetry functions of the single acreage and total acreage.

¾ Speed control of the moving shaft ¾ Filling level indicator ¾ Working speed indicator ¾ Calibration trial with „stop“ signal ¾ Switching of the working lights ¾ Integrated seeding scale ¾ guided machine adjustment adapted to the respective fruit variety

¾ performance control hectare per hour ¾ display and keyboard illumination

Disc to mark the track ¾ The discs to mark the track run hydraulically and can be folded vertically for transport. (adjustable infinitely in width)

The central share pressure adjustment

¾ The pressure on shares is adjusted centrally by a spindle.

¾ Max. pressure on shares approx. 35 kg per disc element (only at 310 DS)

¾ hydr. share pressure adjustment optionally available

The agitator shaft ¾ The agitator shaft is mounted serially in the seed tank of all Seedstar models

¾ After the starting first the power harrow is used not till then the seed shares of the Seedstar follow.

¾ This system avoids (additional) blockages of the seed elements due to crop residues at headland.

The answer is in detail The perfect solution with share automatic.

Serially with hydr.

share automatic

Marker for the track before the seed is bearing

¾ Controlled hydraulically via Seedtron track appliance.

¾ The mounting happens in connection with the hinged stages.

¾ Infinitely adjustment of the track.

Spurs wheel drive ¾ Big dimensioned spurs wheel with pre-load to the ground, cares for constant drive and avoids slippage.

The seed tank ¾ The seed tank is offered in different dimensions. ¾ The dividing walls enable high stability and avoid from shifting of the seed at crosswise working.

¾ Keys between the outlets avoid remaining quantities in the seed tank.

¾ Forward opening seed tank cover for filling with loader.

Easiest mounting and dismounting of the drilling machine

¾ By the hitching system the Seedstar can easily get connected to or disconnected from the power harrow.

10 11www.regent.at

6408

/041

7

www.regent.atRegent Pflugfabrik GmbH

Bahnhofstr. 105 4800 Attnang-Puchheim

Tel. +43 7674 62661 Fax. +43 7674 62207 info@regent.at

RSM-V 252 250 20 12,5 570 250 520RSM-V 252 DS 250 20 12,5 570 250 640RSM-V 312 DS 300 24 12,5 700 / 1050 300 730 / 800

Aress

2500 250 300 95 130 10 275/311 770 880 1065 10703000 300 300 95 130 12 275/311 830 1000 1180 1190 1230Orbit2500 M 250 300 125 170 10 285/344 970 1230 1265 12703000 M 300 300 125 170 12 285/344 1040 1390 1430 1400 13903000 S 300 330 180 250 12 283/341 1100 1490 1530 1450 14554000 S 400 330 180 250 16 283/344 1340 1890KSE HK5000 HK 500 300 220 300 20 312/352/399 2730 27506000 HK 600 300 220 300 24 312/352/399 2980 3000

For the professional in agriculture

Subj

ect t

o te

chni

cal c

hang

es a

nd m

isprin

ts.

Seed

star

Wo

rkin

g w

idth

cm D

rift-

sha

res

Dist

anc

e of

lin

es c

m

Dou

ble

shar

es

Am

ount

of

lines

Seed

tank

ca

pa

city

lite

r

Wei

ght

kg

Tra

nsp

ort

w

idth

cm

ZPW

KP

W

WP

W

Typ

e

Wo

rkin

g

wid

thLe

ngth

of

knife

tine

s

Roto

rs

Packer roller Ripple rollerkW H

P Crumbling

U/mincm mm kg ø460 kg

ø550 kg

ø500 kg

ø450 kg

RSW

Crumbler rollerø450

kg

Sales partner

ø500 kg

Semi-mounted on the roller ¾ The working depth of the power harrow can be adjusted autonomously from the seeding machine and the roller.

¾ If the seeding machine is mounted on the roller, the tines can be conserved at stony soils.

¾ Re- solidification and crumbling are reinforced obviously through the displacing of the weight to the roller.

¾ This enables a more evenly seeding depth, protects from erosion and leachates and results in higher production!

En66

16

Single straw weeder ¾ Tines are mounted on the pressure roll to enable simple smearing over of the seed rill. (from light to average soils)

Seed weeder ¾ The seed weeder is equipped with springed double tines and 2 hinged stages.

www.regent.at