Power for a Wireless World Measuring Wireless Charging ... · Power for a Wireless World...
Transcript of Power for a Wireless World Measuring Wireless Charging ... · Power for a Wireless World...
Power for a Wireless World
Measuring Wireless Charging EfficiencyIn the Real World
WPC Trade ConferenceSeoul12 November, 2015
Power for a Wireless WorldEfficiency
Matters
• Who cares about efficiency?• IKEA• McDonald’s• EPA/China/EU/ Gov’t agencies• Auto makers• Consumers• Who doesn’t care?
Power for a Wireless WorldPower for a Wireless World
Industry-Wide Problem:
There is no Standardized test methodology for specifying power
efficiency of a wireless charging system
Syn
chro
no
us
DC
-DC
B
uck
Re
gula
tor
Ba
tte
ry C
har
ge
r
Bri
dge
Dri
verDC
Input
WPT Transmitter
WPT Receiver
Power for a Wireless World
1. DC out A: Not a valid representation of real-world application2. DC out B: A good proxy, if the right load range is selected3. DC out C: The real-world view, also allows complete energy
analysis
No Measurement
Standard
Syn
chro
no
us
DC
-DC
B
uck
Re
gula
tor
Ba
tte
ry C
har
ge
r
½ B
rid
ge D
rive
rDCInput
DC OutC
WPT Transmitter
WPT Receiver
DC OutA
DC OutB
Power for a Wireless World
Two
Architectures
Rezence perimeter coil Qi planar coil
Loosely Coupled Closely Coupled
Power for a Wireless WorldArchitecture
Comparison
Architecture Representative Standards
OperatingFrequency
AntennaStructure
Benefits
Loosely Coupled
• Rezence • 6.78 MHz Perimeter • Extended Z-distance1
CloselyCoupled
• Qi • 110 ~ 205 kHz Planar • Highly efficient• Low cost
Question: Why not use resonant architecture for all applications?Answer: Efficiency and cost tradeoffs make it inappropriate to do so.
1. There are no Rezence products in the market, so benefits are as per the promotional materials from the A4WP
Power for a Wireless World
Use-Case
Examples
Resonant: Under-surface mount
Inductive: Automotive
Inductive: Charging Stand
Inductive: Charging Plate
Power for a Wireless World
Ideal Definition of Efficiency
Efficiency should be calculated as spatial average:
“Total joules into the battery divided by total joules into the transmitter averaged over the charge area/volume for a charge
cycle”
Power for a Wireless WorldEfficiency
Experiment
1. Loosely-coupled, high-frequency wireless charger
– EPC-9112
– Similar to A4WP/Rezence Class 3
– 6.78 MHz operation
2. Closely-coupled, low-frequency wireless charger
– BQ500212
– Qi spec 1.1.2, Type A11
– 110 ~ 210 kHz
Power for a Wireless WorldWhere is Efficiency
Measured?
Li+
Sync
hron
ous
DC
-DC
Buc
k Re
gula
tor
Bat
tery
Ch
arge
r
DC In
AC Adapter
Wireless Transmitter
Wireless Receiver
Efficiency Measurement
Taken at the optimal spatial position and load power (5W, 4.2V @ 1.2A)
DC out
AC
DC
h
Power for a Wireless WorldBattery Model:
2100 mA hr.
Model determines load resistance, voltage
and current test conditions
Power for a Wireless WorldTotal Energy
27 kJ
Energy required for typical (90%) charge-cycle of a 2100 mA hr. battery
Power for a Wireless World
Texas InstrumentsEvaluation Kit bq500212
• 100 ~200 kHz operation• CMOS switches• Würth antenna compliant to
Qi A11
Qi
Flux Field (A11)
Power for a Wireless World
Efficiency Test
Results
• Qi is the most efficient system by design
• Efficiency is impacted by:• Switching frequency• Antenna design• Spatial position / Coil-
coupling coefficient• Maximum Power-
Point Transfer
Power for a Wireless WorldBattery Model:
2100 mA hr.
Total energy over 5% to 95% charge cycle:
27 k Joules
Power for a Wireless World
Real-World Energy Use
Qi system used 33% less energy to charge a battery
27 kJBattery
43.8 kJQi
65.7 kJRezence
Power for a Wireless World Conclusions
1. Real-world conditions must be used to measure efficiency
2. Efficiency should be defined as a spatial average
1. “Total joules into the battery divided by total joules into the transmitter over one charge cycle”
3. Qi is the most efficient system
4. A wireless charging standard that meets all market needs and use-cases must be dual-mode (close and loosely coupled)