Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature...
Transcript of Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature...
![Page 1: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/1.jpg)
Post-Tensioned FloorsDesign for Temperature
Florian Aalami
April 28, 2015
![Page 2: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/2.jpg)
Agenda
• Design objective
• Response of floor slabs to temperature effects
• Design procedure for control of temperature cracks
• Example
![Page 3: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/3.jpg)
Design Objective
• To mitigate the probability of undesirable effects in
floor slabs due to changes in ambient temperature
• Primarily crack formation as a result of tensile stress
• Deflections and secondary strength impact largely
ignored
• Addition of temperature rebar, where needed
![Page 4: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/4.jpg)
Affected Structures
• Lowest levels of exposed structures
• Roof slabs
• Large slabs constructed in warm climates
![Page 5: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/5.jpg)
Response of Floor Systems
• Response of beam and one-way slabs different
than that of two-way systems
![Page 6: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/6.jpg)
Beams and One-Way Systems
• Concrete section under bending and axial forces
cracks when the tensile stress reaches the modulus
of rupture fcr given in ACI 318
• fcr = 7.5 sqrt f’c• The cracking moment Mcr is given by:• Mcr = (fcr + P/A)S where• P = Axial force in design section;• A= area of design section; and• S = section modulus of design section.
![Page 7: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/7.jpg)
Beams and One-Way SystemsPre- and post-cracking stress distribution
At initiation of cracking and for applied moments exceeding Mcr, the added contribution of reinforcement in the element will develop the resistance to the applied moment.
![Page 8: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/8.jpg)
Beams and One-Way Systems
If crack width is of concern, the amount and disposition of reinforcement should be designed for:
• Closely spaced bars• Small diameter• Close to tension face
![Page 9: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/9.jpg)
Two-Way Systems
Design (hypothetical) and elastic stress distribution for column and wall supports
![Page 10: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/10.jpg)
Two-Way Systems
Distribution of elastic and cracked section stress
Cracking moment at the peak of the stress distribution results in local cracking coupled with a drop of the moment at the peak and redistribution of the applied moment. The redistribution of the moment results in automatic limitation of the length of crack and the ability of the section to resist moments in excess of the cracking value.
![Page 11: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/11.jpg)
Design Procedure
• Procedure is empirical
• Based on “hypothetical” stress across design section
• Where computed stress exceeds code limit add
crack control reinforcement
• Place crack control reinforcement in tension zone
![Page 12: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/12.jpg)
Design Procedure
Calculation of crack control reinforcement
Ast = Nc/(0.5fy)
Where,Ast = Area of added reinforcementNc = Tensile forcefy = yield stress of steel
![Page 13: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/13.jpg)
Design Procedure
• Temperature load design is carried out with Dead
and Live Loads
• Lateral loads are not considered
• Use sustained (quasi permanent) loads
![Page 14: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/14.jpg)
Design Procedure
• Analyze structure for regular gravity loads and dT
• dT = change in ambient temperature
• Calculate design strip stresses for load combinations
U1 = 1.00T
U2 = 1.00DL + 1.00PT + 1.00TU3 = 1.00DL + 1.00PT - 1.00T
U4 = 1.00DL + 1.00PT + 0.30LL + 1.00TU5 = 1.00DL + 1.00PT + 0.30LL– 1.00T
Where,T = Change in ambient temperature (dT)
![Page 15: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/15.jpg)
Design Procedure
• Identify sections where stress > 2 sqrt f’c
• Calculate required crack control reinforcement Ast
• Provide reinforcement on tension side if:
Ast > As + Aps
where As is the available rebar in the design section; andAps is the area of bonded reinforcement in the design section
![Page 16: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/16.jpg)
Example Post-Tensioned Slab
![Page 17: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/17.jpg)
Sustained Load Deflection
![Page 18: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/18.jpg)
dT = 50 deg F Deflection
![Page 19: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/19.jpg)
dT = 50 deg F Deflection
![Page 20: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/20.jpg)
dT = 50 deg F Axial XX
![Page 21: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/21.jpg)
dT = 50 deg F Bottom Stress XX
![Page 22: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/22.jpg)
dT = 50 deg F Top Stress XX
![Page 23: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/23.jpg)
Sustained Load Design Stress Top
![Page 24: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/24.jpg)
Sustained Load Design Stress Bot.
![Page 25: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/25.jpg)
Dt = 50 deg F Design Stress Top
![Page 26: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/26.jpg)
Dt = 50 deg F Design Stress Bot.
![Page 27: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/27.jpg)
Envelope of ReinforcementIn this example, Total Load Service stresses governed design
![Page 28: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/28.jpg)
Deflections
In this example, temperature loads re-distribute stresses to slightly reduce cracked deflections
Cracked Sustained Load Deflection 0.56”
Cracked Sustained Load Deflection with Temperature
0.51”
![Page 29: Post-Tensioned Floors Design for Temperature · Post-Tensioned Floors Design for Temperature Florian Aalami April 28, 2015. Agenda •Design objective •Response of floor slabs to](https://reader030.fdocuments.us/reader030/viewer/2022033122/5e8b93639cb75a00493a9d73/html5/thumbnails/29.jpg)
Conclusion
• Exposed concrete floors can be subject to
temperature loads
• Design objective is to mitigate crack formation
• Temperature induced stresses can be quantified
• Add reinforcement to control cracks, if needed