REVISION

Date Rev Remarks

16/12/09 A Draft

CABLE DRAWING:

DRAWING NO.:

MWACAB-0014

DRAWN BY:

DRC

POSEIDON SCIENTIFIC INSTRUMENTS PTY LTD

DATE: 16-Dec-09

SHEET: 1 of 3

17 QUEEN VICTORIA ST, FREMANTLE WA 6160. PHONE (08) 9430 6639 FAX (08) 9335 4650

DRAWING TITLE:

ATIM-T Power Cable

REV:

A

CAB-0XXX (SALEM CODE)

Cable Detail:

Connectors: Description Parts (Qty)

ATIM-T 7W2 Male (Plug) Solder Bucket See Note1 Below(1)

40A High Current Pin See Note2 Below(2)

PSU 7W2 Male (Plug) Solder Bucket See Note1 Below(1)

40A High Current Pin See Note2 Below(2)

Conductors:

Cable1 PRO POWER - CBBR1541 - Wire, Tri Rated,

Black, 10mm

See Note3 Below(??)

Cable2 20AWG Hook-up Wire 20AWG 10/0.25 PVC

600V Black

See Note4 Below(??)

Cable3 20AWG Hook-up Wire 20AWG 10/0.25 PVC

600V Red

See Note5 Below(??)

Misc:

Backshell For connectors See Note6 Below(2)

Sprial Wrap Spiroband, 6mm 50M White See Note7 Below(??)

Overall Length ??+/-5mm

Notes:

1. 7W2 connector can be supplied from Farnell #120-7582. Any equivalent will be OK refer

to data sheets supplied with this drawing.

2. Connector Pins can be supplied from Farnell #120-0479. Any equivalent will be OK refer

to data sheets supplied with this drawing

3. The cable can be supplied from Farnell #117-8331. Any equivalent will be OK refer to

data sheets supplied with this drawing.

4. The cable can be supplied from RS #383-6177 or PSI #CAB-0197. Any equivalent will

be OK refer to data sheets supplied with this drawing.

5. The cable can be supplied from RS #383-6183 or PSI #CAB-0200. Any equivalent will

be OK refer to data sheets supplied with this drawing.

6. The connector backshells can be supplied from Farnell #167-2005. Any equivalent will

be OK refer to data sheets supplied with this drawing

7. The spiral wrap can be supplied from Farnell #303-045. Any equivalent will be OK refer

to data sheets supplied with this drawing.

REVISION

Date Rev Remarks

16/12/09 A Draft

CABLE DRAWING:

DRAWING NO.:

MWACAB-0014

DRAWN BY:

DRC

POSEIDON SCIENTIFIC INSTRUMENTS PTY LTD

DATE: 16-Dec-09

SHEET: 2 of 3

17 QUEEN VICTORIA ST, FREMANTLE WA 6160. PHONE (08) 9430 6639 FAX (08) 9335 4650

DRAWING TITLE:

ATIM-T Power Cable

REV:

A

CAB-0XXX (SALEM CODE)

Typical Drawing:

Close-Up View

REVISION

Date Rev Remarks

16/12/09 A Draft

CABLE DRAWING:

DRAWING NO.:

MWACAB-0014

DRAWN BY:

DRC

POSEIDON SCIENTIFIC INSTRUMENTS PTY LTD

DATE: 16-Dec-09

SHEET: 3 of 3

17 QUEEN VICTORIA ST, FREMANTLE WA 6160. PHONE (08) 9430 6639 FAX (08) 9335 4650

DRAWING TITLE:

ATIM-T Power Cable

REV:

A

CAB-0XXX (SALEM CODE)

Pinouts Table:

PSU-End Module-End

Pins(3) Pins(3)

1A +48V 2A

1 +5V 2

2 +5V 1

3 0V 5

4 0V 4

5 0V 3

2A 48RNT 1A

Assembly Details:

Connection Detail:

From: (PSU) PSU Front Panel Connector

To: (ATIM-T) PCB Power Connector

3

Interconnect Solutionshttp://www.3M.com/interconnects/

3M is a trademark of 3M Company.For technical, sales or ordering information call

800-225-5373

3M™ D Sub EMI Junction ShellMetalized Plastic

Physical

Environmental

"RoHS compliant" means that the product or part does not contain any of the following substances in excess of the following maximum concentration valuesin any homogeneous material, unless the substance is in an application that is exempt under RoHS: (a) 0.1% (by weight) for lead, mercury, hexavalent

chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing,this information represents 3M's knowledge and belief based upon information provided by third party suppliers to 3M.

Shell and Hardware Shell Material: ABS

Shell Plating: Nickel Over CopperHardware: (2) Jackscrews #4-40 × .438"

(2) Saddle Washers #4(2) Nuts #4-40(2) Screws #4-40 × .450"

Material: SteelPlating: Bright Zinc

Compression Insert:Material: Thermo Plastic Elastomer

Flammability: UL 94HBDurometer: 75 + / -5

Mounting Hardware: See Specification Sheet TS-0142

Temperature Rating: 0°C to +75°C

• Protection from EMI/ESD• Easy assembly reduces time and labor for low

cost• Light weight and a compact design• Strain Relief compensates for multiple cable

diameters• Jack screws provide positive retention• RoHS* compliant

TS-2132-02Sheet 1 of 3

Date Modified: January 15, 2007

3

Interconnect Solutionshttp://www.3M.com/interconnects/

3M is a trademark of 3M Company.For technical, sales or ordering information call

800-225-5373

DIM. "B"

DIM. "C"

DIM. "A"

DIM. "E"[DIM. "E"]

DIM. "D"O

DIM. "F"

3M™ D Sub EMI Junction ShellMetalized Plastic

TS-2132-02Sheet 2 of 3

.0 .00 .000inch ± .1 ± .01 ± .005

[ ] D im ens io ns fo r R e fe re nce O n ly

T o le rance U n less N o ted

[m m ]In ch

Backshell Dimension TableTable 1

Dim. "A" Dim. "B" Dim. "C" Dim. "D" Dim. "E" Dim. "F" Min Max*3357-6209-1C 1.217 [30.91] 1.692 [42.98] .400 [10.16] N/A .984 [24.99] 0.19 [ 4.8] 0.35 [8.9]3357-6215-1C 1.540 [39.12] 1.650 [41.91] .400 [10.06] N/A 1.312 [33.32] 0.19 [ 4.8] 0.35 [8.9]3357-6225-1C 2.090 [53.08] 1.800 [45.72] .522 [13.26] .710 [18.03] 1.857 [47.17] 0.19 [ 4.8] 0.46 [11.7]3357-6237-1C 2.734 [69.44] 1.975 [50.17] .726 [18.44] .906 [23.01] 2.500 [63.50] 0.30 [ 7.6] 0.68 [17.27]3357-6250-1C .770 [19.56] 2.645 [67.18] 2.000 [50.80] .726 [18.44] .940 [23.88] 2.406 [61.11] 0.30 [ 7.6] 0.84 [21.34]

Note: *These numbers will vary depending upon the compressibility of the wire.

Table 1 - Junction Shell

.640 [16.26]

Dimensions3M Part Number Cable O.D. Range

3

Interconnect Solutionshttp://www.3M.com/interconnects/

3M is a trademark of 3M Company.For technical, sales or ordering information call

800-225-5373

3M™ D Sub EMI Junction ShellMetalized Plastic

Table 2 - Compression Inserts

InsertFor

Dimensions

1 2 3 4 5 6G

OD ID OD ID OD ID OD ID OD ID OD ID

3357-6209 0.475[ 12.07 ]

0.320[8.13 ]

0.360[ 9.14 ]

0.315[ 8.00 ]

0.360[ 9.14 ]

0.285[ 7.24 ]

0.360[ 9.14 ]

0.255[ 6.48 ]

0.360[ 9.14 ]

0.210[ 5.33 ] N/A N/A 0.475

[ 12.07 ]3357-6215

3357-6225 0.600[ 15.24 ]

0.450[ 11.43 ]

0.450[ 11.43 ]

0.410[ 10.41 ]

0.450[ 11.43 ]

0.370[ 9.40 ]

0.450[ 11.43 ]

0.300[ 7.62 ]

0.450[ 11.43 ]

0.230[ 5.84 ]

N/A N/A 0.600[ 15.24 ]

3357-6237 0.655[ 16.64 ]

0.650[ 16.51 ]

0.700[ 17.78 ]

0.620[ 15.75 ]

0.810[ 20.57 ]

0.570[ 14.48 ]

0.655[ 16.64 ]

0.500[ 12.70 ]

0.655[ 16.64 ]

0.425[ 10.80 ]

0.655[ 16.64 ]

0.350[ 8.89 ]

0.810[ 20.57 ]

3357-6250 0.810 [20.57]

0.650 [16.51]

0.700 [17.78]

0.620 [15.75]

0.655 [16.64]

0.570 [14.48]

0.655 [16.64]

0.500 [12.70]

0.655 [16.64]

0.425 [10.80]

0.655 [16.64]

0.350 [8.89]

0.810[ 20.57 ]

Backshell Size09 = 9 Pin15 = 15 Pin25 = 25 Pin37 = 37 Pin50 = 50 Pin

3357-62XX-1COrdering Information

TS-2132-02Sheet 3 of 3

Cable Insert Dimension TableTable 2

Elastomeric Backshell InsertsFigure 1

1 625

4 3

DIM. "G"O(Collar)

ID

3

Printed in USA.Minimum 10%Post-Consumer Fiber

Important NoticeAll statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.

Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.

3M Electronics6801 River Place Blvd.Austin, TX 78726-9000800/225-5373www.3M.com/electronics © 3M 2007

Tri Rated 10MM

Page <1> 17/11/09 V1.0

http://www.farnell.comhttp://www.newark.comhttp://www.cpc.co.uk

Features:• Heat resisting PVC insulated.• CK type.• UL style 1028; CSA type TEW; BS6231.

Specifications:Conductor:10mm2 (8AWG) (80/0.4mm*) plain annealed copper bunch meeting the requirements of BS6360, class 5.UL subject 758, CSA standard C22.2 no.127.Minimum cross-sectional area : 8.20mm2.Maximum lay of bunch : 76mm.Maximum resistance at 20°C : 1.91Ω/km.Insulation:PVC compound meeting the requirements of type T13 to BS EN 50363.Class 43 PVC to UL1581, class 28 to CSA standard C22.2 no.127.Minimum thickness at any one point : 1.02mm(UL/CSA).Minimum average thickness : 1.14mm (BS).Minimum overall diameter : 5.7mm (BS).Maximum overall diameter : 7.2mm (BS)Lay up : Not applicable.Screen : Not applicable.Sheath : Not applicable.

Part Number Table

Description Part Number

Wire, Tri Rated, Black, 10mm, 100m CBBR1541

Wire, Tri Rated, Red, 10mm, 100m CBBR1542

Wire, Tri Rated, Green/Yellow, 10mm, 100m CBBR1543

Wire, Tri Rated, Blue, 10mm T/RATED 10MM BLU

Wire, Tri Rated, Grey, 10mm, 100m T/RATED 10MM GRY 100M

Wire, Tri Rated, Brown, 10mm, 100m T/RATED 10MM BRN 100M

Disclaimer This data sheet and its contents (the "Information") belong to the Premier Farnell Group (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposesin connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied.The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this datasheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damageresulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. SPC pro-Power is the registered trademark of the Group. © Premier Farnell plc 2009.

* This is a nominal number of strands.* All wires made to meet minimum cross-sectional area and maximum resistance as set in BS specification.

HOOK-UP WIREPVC INSULATION

169

† Also meets MIL-W-76B Type LW*See color chart below

11885500 B-32 32 7/40 0.010 0,25 0.028 0,71 1–6611885511† B-30 30 7/38 0.010 0,25 0.032 0,81 1–6611885522† B-28 28 7/36 0.010 0,25 0.034 0,86 1–1011885533† B-26 26 7/34 0.010 0,25 0.038 0,96 1–1911885544† B-24 24 7/32 0.010 0,25 0.043 1,09 1–1911885544//1199 B-24 24 19/36 0.010 0,25 0.043 1,09 1–1911885555† B-22 22 7/30 0.010 0,25 0.050 1,27 1–1911885555//1199 B-22 22 19/34 0.010 0,25 0.050 1,27 1–1911885566† B-20 20 7/28 0.010 0,25 0.058 1,47 1–1911885566//1199 B-20 20 19/32 0.010 0,25 0.058 1,47 1–1911885577 B-18 18 7/26 0.010 0,25 0.068 1,73 1–1911885577//1199 B-18 18 19/30 0.010 0,25 0.068 1,73 1–1911885588//1199 B-16 16 19/29 0.010 0,25 0.077 1,96 1–1911885599//1199 B-14 14 19/27 0.010 0,25 0.091 2,31 1–10

Alpha Type Conductor Insul. Thickness Diameter StockPart No. Designation AWG Strand Inches mm Inches mm Colors*

MIL-W-16878E TYPE B105°C, 600 VOLT

PVC INSULATIONUL 1015, CSA TEW-105105°C, 600 VOLT

CHARACTERISTICSOPERATING TEMPERATURE: –55°C to 105°C

VOLTAGE RATING: 600 Volt

PRODUCT DESCRIPTION: Conductor: Stranded Tinned Copper Insulation: Color-Coded PVC

SPECIFICATIONS MIL-W-16878E Type B

AVAILABILITY 100 ft (30,5m), 1000 ft (305m) put-ups

CHARACTERISTICSOPERATING TEMPERATURE: –20°C to 105°C

VOLTAGE RATING: 600 Volt

PRODUCT DESCRIPTION: Conductor: Stranded Tinned Copper Insulation: Color-Coded PVC

SPECIFICATIONS UL AWM Style 1015 CSA TEW-105

AVAILABILITY 100 ft (30,5m), 1000 ft (305m) put-ups

®

3070 24 7/32 0.032 0,81 0.088 2,24 1–10+283071 22 7/30 0.032 0,81 0.094 2,38 1–10+28,293073 20 10/30 0.032 0,81 0.100 2,54 1–10+283075 18 16/30 0.032 0,81 0.112 2,85 1–10+28,293077 16 26/30 0.032 0,81 0.124 3,14 1–10+28,293079 14 41/30 0.032 0,81 0.134 3,61 1–10+28,293080 12 65/30 0.032 0,81 0.162 3,93 1–44+283081 10 105/30 0.032 0,81 0.180 4,83 1–40+28

Alpha Conductor Insul. Thickness Diameter StockPart No. AWG Strand Inches mm Inches mm Colors*

*See color chart below

1–White 3–Red 5–Yellow 7–Brown 9–Gray 11–White/Black 13–White/Green 15–White/Blue 17–White/Orange 19–White/Violet 29–Yellow/Green2–Black 4–Green 6–Blue 8–Orange 10–Violet (purple) 12–White/Red 14–White/Yellow 16–White/Brown 18–White/Gray 28–Green/Yellow 30–Pink

*STOCK COLOR CHART

Web Site: www.alphawire.com Toll Free: 1-800-52 ALPHA • Telephone: 908-925-8000 • Fax: 908-925-6923Email: info@alphawire.com Europe/UK Telephone: +44 (0) 1932 772422 • Europe/UK Fax: +44 (0) 1932 772433