POPLIN - deyu-design.com · POPLIN INSTALLATION INSTRUCTIONS VANITY K-96016T-1/-4/-8...
Transcript of POPLIN - deyu-design.com · POPLIN INSTALLATION INSTRUCTIONS VANITY K-96016T-1/-4/-8...
POPLININSTALLATION INSTRUCTIONS
VANITY
K-96016T-1/-4/-8K-96017T-1/-4/-8
-1-
�
�
�
�
�
�
Observe all local plumbing and building codes.
Prior to installation, unpack the new lavatory and inspect itfor damage. Return the lavatory to its protective cartonuntil you are ready to install it.
All information in these instructions are based the latestproduct information available at the time of publication.Kohler China reserves the right to make changes inproduct characteristics, packaging, or availability at anytime without notice.
Fixture dimensions are nominal and conform to tolerancesestablished by ASME Standards (A112.19.2-2013).The product complies with GB 6952-2015.Please purchase 880089-CP as accessory to match withdraw bar faucet of Kohler brand.
Make sure that the wall and floor are squareand plumb to ensure proper installation.IMPORTANT:
�
�
�
�
�
� ASME (A112.19.2-
2013)GB 6952-2015
880089-CP
ORDERING INFORMATION
Poplin Vanity Top 940mm .............................K-96016T-1/-4/-8
Poplin Vanity Top 1245mm ...........................K-96017T-1/-4/-8
940mm .................................K-96016T-1/-4/-8
1245mm ...............................K-96017T-1/-4/-8
REQUIRED MATERIALS/
(NOT SUPPLIED)
TOOLS
�
�
�
�
�
�
�
Level
Drill with bit6mm
14mm wrench
Framing square
Channel lock pliers
Tape measure
Pencil
�
�
�
�
�
�
�
6mm
14mm
No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 5281372 528137
8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA POST CODE: 2564108 256410
©
©
Copyright Kohler China Investment Co., Ltd. 2016
20161305550-T01-A
-2-
ROUGHING-IN DIMENSIONSROUGHING-IN DIMENSIONS
UNIT: mm:
Reference Value
K-96016T-1
K-96016T-4
K-96016T-8
Installation Side
Installation Side
Installation Side
79
79
79
19
19
19
190
190
190
139
139
139
303
303
303
569
569
569
356
356
356
467
467
467
940
940
940
79
79
79
303
303
303
35
3- 35
3- 35
45
45
45
102
203
1305550-T01-A
Fig.#11
Kohler reserves the right to change marked dimensions without prior notice.
K-96017T-1
K-96017T-4
K-96017T-8
-3-
35
3- 35
3- 35
45
45
45
1245
1245
1245
467
467
467
79
79
79
303
303
303
569
569
569
356
356
356
102
203
Installation Side
79
139
19
190
303
Installation Side
79
139
19
190
303
Installation Side
79
139
19
190
303
1305550-T01-A
-4-
�� Install the faucet and drain to the lavatory according to the
manufacture's instructions.
�
CAUTION: Risk of product damage. Do notovertighten the cap nuts.Overtightening may causedamage to the product.
Clean the lavatory top.�
�� Apply some sealant continuously and evenly around the
top of the vanity. Carefully place the lavatory on the
cabinet, and then gently press down until level. Wipe
away excess sealant.
Fig.#33
1. 2 3
2.
NOTE: 1. Height dimensions marked in fig. 2 and fig. 3 could
be adjusted per your the vanity height or the actual
height of the console leg.
2. Other fastening devices of sufficient size and
strength may also be used.
550m
m WasteOutlet
Waste
630m
m
80mm
Fig.#22
Install the Basin
Note! The lavatory tops must be installed on a cabinet or
matching metal stand (refer to Installation and User Guide
packed with the cabinet or stand for installation details).
Recommend Kohler metal square leg or Kohler bathroom
furniture for support or decoration.
�
(
)
�
�
76mm
� Rough-in the supplies and the drain piping.
The supply stop handles cannot extend more than
76mm from the finish wall when in the open position.
NOTE:
1305550-T01-A
-5-
IMPORTANT CONSUMER INFORMATIONIMPORTANT CONSUMER INFORMATION
CARE AND CLEANING
To keep your lavatory looking new, make sure you rinse it out
thoroughly after each use. on this
product, as they will scratch and ruin the surface. Stubborn
stains, paint, or tar can be removed with turpentine or paint
thinner.
DO NOT USE ABRASIVES
Caution! Risk of product damage.
Many cleaners contain abrasive and chemical substances,
and should not be used for cleaning stainless steel, enamel,
plated or plastic fittings.
These finishes should be cleaned using a mild washing up
detergent or soap solution, rinsed and then wiped dry with a
soft clean cloth.
1.
2.
3.
4.
Install the Plumbing
1. Install the drain in accordance with the manufacturer sinstructions.
Make sure a watertight seal exists on allbasin drain connections.
Provide access to the plumbing connectionsfor future plumbing maintenance.
2. Connect the hot and cold water supplies.
3. Open the hot and cold water valves, and check the supplyconnections for leaks.
4. Run water into the basin, and check the drain connectionsfor leaks.
Caution!
Caution!
,
Fig.#44
1305550-T01-A