Polymer Processing Presentation
Transcript of Polymer Processing Presentation
![Page 1: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/1.jpg)
pdf file can be downloaded at
http://pioneer.netserv.chula.ac.th/~sanongn1
Polymer Processing
![Page 2: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/2.jpg)
There are many processes for plastics. Selection of a process depends on many factors including:
- Quantity and production rate- Dimensional accuracy and surface finish- Form and detail of the product- Nature of material- Size of final product
In general, plastics processes have three phases: 1. Heating - To soften or melt the plastic2. Shaping / Forming - Under constraint of some kind3. Cooling - So that it retains its shape
Polymer Processing
![Page 3: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/3.jpg)
Thermoplastics start as regular pellets or granules and can be remelted.
Thermosetting materials start as liquids/syrups, often called "resins", as powders or partially cured products ("preforms") which need heat for the shaping phase. The shaping is accompanied by a chemical reaction, which means that the material does not soften on reheating. The reaction may be exothermic (giving heat out), in which case cooling is required.
![Page 4: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/4.jpg)
1.Extrusion
2.Extrusion-based processes
3.Thermoforming
4. Injection molding
5.Compression and transfer molding
6.Rotational molding
7.Blow molding
8.Plastic foam molding
Processes
![Page 5: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/5.jpg)
1.Extrusion
-the forcing of a plastic or molten material through a shaped die by means of pressure.
![Page 6: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/6.jpg)
Single screw extruder
Twin screw extruder
![Page 7: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/7.jpg)
-screw has one or two ‘flights’ spiraling along its length.-φ to outside of the flight is constant along the length to allow the close fit in the barrel.-core is of varying φ and so the spiraling channel varies in depth.-in general, the channel depth ↓ from feed end to die end pressure ↑
![Page 8: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/8.jpg)
The zones in an extruder1.Feed zone
-preheat polymer and convey it to the subsequent zones.
-screw depth is constant 2.Compression zone (transition zone)
-channel depth ↓-expel air trapped between original granules-heat transfer from the heated barrel walls is
improved ‘coz material thickness ↓-density change during melting is accommodated
melt sharply very short compression zone melt gradually very long compression zone
![Page 9: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/9.jpg)
3.Metering zone-constant screw depth-homogenize the melt -supply to the die region material which is of
homogeneous quality at constant T & P4. Die zone
-breaker plate - screen pack (perforated steel plate)a) sieve out extraneous material, e.g. ungeledpolymer, dirt and foreign bodiesb) allow head P to develop by providing a
resistance for the pumping action of the metering zone
c) remove ‘turning memory’ from the melt
![Page 10: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/10.jpg)
An example of ‘turning memory’
![Page 11: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/11.jpg)
Specialty featuresBasic single screw extruder: good dispersive mixer, poor
distributive mixer (figure below to illustrate distributive and dispersive mixing)
![Page 12: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/12.jpg)
Specialty featuresBasic single screw extruder: good dispersive mixer, poor
distributive mixer (figure below to illustrate distributive and dispersive mixing)
![Page 13: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/13.jpg)
Specialty featuresHave ‘mixing head’ beyond metering zone: promote
mixing by means of studs, slots, ribs Simplest: ‘smear head’
![Page 14: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/14.jpg)
Specialty features
More sophisticated static mixing device: ‘cavity transfer mixer’ (CTM) Be developed at the Rubber and Plastics
Research Association, RAPRADepend on cutting and redistributing the melt to
achieve mixing.Consist of cylindrical end, the rotor attached to the
screw, the stator.
![Page 15: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/15.jpg)
Specialty features
Have provision for venting volatiles during extrusion. Provided with a venting port on the barrelDecompress the melt at this point to prevent its
being expelled from the port
![Page 16: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/16.jpg)
Flow mechanisms: Melting Conducted heat from the barrel heater + friction
The melting process
![Page 17: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/17.jpg)
Flow mechanisms: Conveying-Drag flow
-dragging along by the screw of the melt as the result of the frictional forces
-equivalent to viscous drag between stationary and moving plates separated by a viscous medium.
-constitute output component for the extruder.-Pressure flow
-P gradient along the extruder (high P at the output end, low at the feed end
-Leak flow-finite space between screw and barrel through which material can leak backwards.
Total flow = drag flow – pressure flow – leak flow
![Page 18: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/18.jpg)
1. Basic flow patterns-Maintain laminar flow
The extrusion die
Conjectural patterns for a rod die
![Page 19: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/19.jpg)
1. Basic flow patterns-Maintain laminar flow-Not ‘zero length profile’
(like that shown in part (a) in figure)
The extrusion die
Conjectural patterns for a rod die
![Page 20: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/20.jpg)
1. Basic flow patterns-Maintain laminar flow-Not ‘zero length profile’
(like that shown in part (a) in figure)
-No abrupt changes (like that shown in part (b) in figure)
The extrusion die
Conjectural patterns for a rod die
![Page 21: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/21.jpg)
1. Basic flow patterns-Maintain laminar flow-Not ‘zero length profile’
(like that shown in part (a) in figure below)
-No abrupt changes (like that shown in part (b) in figure below)
-‘dead spot’ occurs in the corners in part (a) and (b) Extrudate with uneven heat and shear history
The extrusion die
Conjectural patterns for a rod die
![Page 22: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/22.jpg)
Parallel and converging flow
in a parallel flow, fluid element remains intact as it proceeds along the channel
in converging flow•both tensile and shear forces occur
•streamlines converge •fluid element becomes distorted as the result of developing tensile stress•melt is stretching as it narrows down towards an exit
![Page 23: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/23.jpg)
The extrusion die
2. Die entry effects
Tensile stress exceed the tensile strength of the melt (usually ~ 106 Nm-2)
extrudate will be of irregular shape
called melt fracture
![Page 24: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/24.jpg)
The die entrance is tapered:
1.Eliminate the dead spots in the corners, maintaining a steady heat and shear history
2.Minimize the development of tensile stresses, and minimize distortion of the streamlines
Long die land extend the process time which helps to eliminate memory of earlier processing, e.g. screw turning memory
The smoother the streamlines, the faster it’s possible to run the process and the better the product will be.
Deborah Number, Ndeb*
![Page 25: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/25.jpg)
Relaxation time – the characteristic timescale for which a melt has memory
-describe as its viscous and elastic responses to an applied stress
sNmmNs
=××
== 2
2
modulusviscosity timerelaxation
process of timescaleprocessin material, of timerelaxation
=debN
If Ndeb>1, process is dominantly elastic.
If Ndeb<1, process is predominantly viscous.
![Page 26: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/26.jpg)
Cogswell (“Polymer Melt Rheology,” Godwin, London, 1981) has provided an example of polymer melt flowing round a bend and then through a relatively narrow die. •time scale from the bend to the die ~ 10 s
•relatively low stress•relatively high viscosity ~ 105 Nsm-2
•elastic modulus increases with increasing stress
![Page 27: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/27.jpg)
1. Flow from bend to die
1010
100N
s 10 process of timescale
s 1001010 timerelaxation
1010
modulusviscosity :stress low
deb
3
5
23
25
==
=
==
= −
−
NmNsm
i.e. this process is predominantly elastic
![Page 28: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/28.jpg)
1.01.0
01.0N
s 0.1 process of timescale
s 01.01010 timerelaxation
1010
modulusviscosity :stresshigh
deb
5
3
25
23
==
=
==
= −
−
NmNsm
2. Flow through die
i.e. this process is predominantly viscous
![Page 29: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/29.jpg)
physical behavior of the extrudate interpretationone would expect that the high shear, viscous
process ‘cancels out’ all that has gone before;
![Page 30: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/30.jpg)
physical behavior of the extrudate interpretationone would expect that the high shear, viscous
process ‘cancels out’ all that has gone before; however, instinct is wrong.
the extrudate will curl!!the process in the benda long timescale
elasticthe chains are not permanently realigned.The subsequent short timescale deformation in the diehigh shear does not remove this elastic distortion
![Page 31: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/31.jpg)
3. Die exit instabilitiessharkskin-roughening of the surface of the extrudate-caused by tensile stresses:
the melt, with max velocity at the center and zero at the wall, leaves the die lips material at the wall accelerate to the velocity at which the extrudate is leaving the die generate tensile stress.. If tensile stress exceeds tensile strength, surface ruptures.orange peel-when conditions become more intense, e.g. P at the extruder becomes excessive, or the die T drops-coarser-grained appearance
![Page 32: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/32.jpg)
bambooing-the whole extrudate ‘snaps back’
Extra heating of the die will often help to remedy these defects, by thermally relaxing the stresses and lowering viscosity
![Page 33: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/33.jpg)
4. Die swell-Effect in which the polymer swells as it leaves the die.-Extrudate differs in its dimensions from those of the die
orifice.-Extruded rod has larger diameter and pipe has thicker
walls, e.g. o.d. ↑, i.d. ↓
Result of the elastic component in the overall response of the polymer melt to stress. recovery of the elastic deformation as the extrudate leaves the constraint of the die channel and before it freezes.
![Page 34: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/34.jpg)
![Page 35: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/35.jpg)
Part Cost - low Tool Cost - low Production Capability -high Short lead times to production Uniform cross section of parts Multiple materials are possible in the same part.
![Page 36: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/36.jpg)
2.Extrusion-based processes
Profile extrusion: pipe, sheet
Tubular blown film extrusion: plastic bag- Polypropylene
Cross-head extrusion: electrical cord
Synthetic fibers: polyester
Netting: Garden uses, fruit packaging
Co-extrusion
![Page 37: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/37.jpg)
Pipe extrusion
![Page 38: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/38.jpg)
Sheet extrusion
Film thickness: 0.5 – 20 mil (1 mil = 0.001 inch)
![Page 39: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/39.jpg)
![Page 40: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/40.jpg)
![Page 41: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/41.jpg)
![Page 42: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/42.jpg)
Netting-Garden uses, fruit packaging
-Made with annular dies but with outer die and the central mandrel counter-rotating and close fitting
-Both parts have slots so that concentric sets of filaments extrude
-When counter-rotation starts the filaments cross one another to form welded junctions and a net pattern.
![Page 43: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/43.jpg)
Tubular blown film extrusion
![Page 44: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/44.jpg)
Co-extrusion
-Extrusion of more than one type of polymer at once to give a laminate product.
-Require a separate extruder for each polymer
-Multilayer product forming at a die
-‘tie-layers’: bond the functional layers together
![Page 45: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/45.jpg)
Multi-Layer … Mono MaterialFor non-demanding applications, a mono material sheet is usually specified. This is a sheet in which there is only one material. With a more demanding application, a multi-layer sheet is used. Multi head extruders feed into the extrusion die with the differing materials. Multi layer sheeting, with a heat compliant top layer, can used to make heat-sealed applications. PVC / PE for Meat Trays, and CPET / APET for Meat Trays and Ready Meals.
![Page 46: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/46.jpg)
3. Thermoforming
![Page 47: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/47.jpg)
![Page 48: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/48.jpg)
-air pressure and plug assisted forming of the softened sheet. -invariably automated and faster cycle times-only thermoplastics sheet can be processed by this method.-The largest application is for Food Packaging. -Other industries include Toiletries, Pharmaceuticals and Electronics
![Page 49: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/49.jpg)
-Food related applications such as Meat Trays, Microwave & Deep Freeze Containers, Ice Cream and Margarine Tubs, Snack Tubs, Bakery and Patisserie packaging, Sandwich Packs and Vending Drink Cups
-Manufacturing Collation trays, Blister packaging and Point of Sale display trays.
![Page 50: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/50.jpg)
4. Injection moldingInjection molding is accomplished by forcing molten plastic under pressure into a cavity formed between two matched metal mold halves. Once the plastic cools, the molds are opened and the part is removed.
![Page 51: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/51.jpg)
-Part cost - low -Tooling cost - high -Production Rate - high -Can produce intricate parts -Large variety of polymers gives wide range of properties. -Can produce a wide range of part sizes with different press sizes.
![Page 52: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/52.jpg)
![Page 53: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/53.jpg)
mold
![Page 54: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/54.jpg)
Functions:
1.Allow rapid freezing of polymer: isolate the cavity and permits withdrawal of the screw
2.Narrow and thin solid section: be sheared off easily after demolding
3. Increase shear rates as melt flows through: lower viscosity to ease rapid and complete filling of complex shapes
![Page 55: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/55.jpg)
![Page 56: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/56.jpg)
![Page 57: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/57.jpg)
Problems:
-sink marks and voids
-weld lines
![Page 58: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/58.jpg)
![Page 59: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/59.jpg)
Weld line: formed where polymer flows meet
Can be moved to a position on the molding where unimportant
![Page 60: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/60.jpg)
![Page 61: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/61.jpg)
5. Compression and transfer molding
![Page 62: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/62.jpg)
-place a pre-weighed amount of material in a matched metal mold and closing the mold. -heat and pressure cause the material to liquify and flow into the voids in the tool where it chemically reacts and hardens into the final shape. -very large shapes can be molded in compression presses.
![Page 63: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/63.jpg)
Advantages of compression molding (compared with injection molding)
-Low scrap arisings
-Low orientation in the moldings
-well distributed fibrous fillers
-low residual stress product
-retained mechanical and electrical properties
-low mold maintenance
-low capital and tooling costs
![Page 64: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/64.jpg)
- developed from “compression molding” process - Reservoir of molding compound is located in the mold - upon closure, it is transferred via runners to the cavities-To give many small parts more easily- reduce the risk of damage or movement of thin or delicate mold parts- be faster due to better heat transfer through the runners
![Page 65: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/65.jpg)
Disadvantages when compared with compression
-Give unwelcome orientation in the product
-Increase wear and maintenance costs
-Tooling is more complex and more expensive
-Runners owe scrap
![Page 66: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/66.jpg)
6.Rotational molding
![Page 67: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/67.jpg)
-cast hollow plastic parts with few restrictions regarding size or complexity
Very stable parts - no molded in stresses Low tooling cost for large parts Suited for low volume production Can produce complex part geometries Can mold in metal inserts and graphics
![Page 68: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/68.jpg)
![Page 69: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/69.jpg)
![Page 70: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/70.jpg)
7. Blow molding
Extrusion blow molding
‘parison’
ขวดน้ําเปลา สีขาวขุน ทําจาก PP
![Page 71: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/71.jpg)
Extrusion blow molding
Watering cansVenting ductsAutomotive fuel tanks
Typical productsBottles and containers
![Page 72: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/72.jpg)
-Part cost - moderate -Tooling Cost - moderate -Production rate - moderate to high -Blow molding produces parts with the highest strength to weight ratio of any plastic process. Complex, hollow parts are formed with no internal stresses. Parts as large as 12 ft. x 4 ft. x 4 ft. can be formed
![Page 73: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/73.jpg)
Stages
1. The hot plastic extruded into the mold in pipe form.
2. While still hot, the plastic is trapped in the mold, a hot knife cuts it off at the top and it is also pinched at the bottom.
3. The mold then moves to the right. An air hose is inserted into the top.
4. The plastic in the mold expands to fill the mold.
5. The mold then separates, which releases the plastic (bottle).
![Page 74: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/74.jpg)
![Page 75: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/75.jpg)
![Page 76: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/76.jpg)
Carbonated drinks using PET
The tube ‘preform’ made by injection molding to a very cold mold to quench it in its amorphous state
Is reheated to blowing T (just about its Tg ) and stretch blown
Develop biaxial orientation in the product
Alternate name for this process is ‘stretch-blow’
Injection blow molding
![Page 77: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/77.jpg)
![Page 78: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/78.jpg)
8.Plastic foam molding
-low-pressure injection molding process that is capable of producing very large structural parts. -The molten plastic material is injected into a mold after being mixed with a blowing agent or high-pressure gas. -This produces bubbles in the plastic causing it to foam. The foam retains the properties of the plastic but weighs less because of reduced density.
![Page 79: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/79.jpg)
![Page 80: Polymer Processing Presentation](https://reader031.fdocuments.us/reader031/viewer/2022012403/552327004a79595d5e8b4b82/html5/thumbnails/80.jpg)