© Poly Rubber Products, All Rights Reserved Manufacturer & Exporter of Rubber Products.
Poly V Products - Taylormhc
Transcript of Poly V Products - Taylormhc
1
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected] phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
Poly V ProductsPoly V Products
1.90” Roller Tube OD Inserts
• Injection Molded• Conductive plastic with 2 ABEC-1 ball bearings• 43mm OD (Effective diameter) – 1.69”
Standard roller tube is 1.90” OD x .065” wall thickness.• Other sizes available – call for information• 43MM insert OD with belt installed is 1.84” final OD
Poly V Belt ConfigurationAccommodates Hutchinson ConveyXonic “J” series - 2, 3, or 4 ribs.
Ralphs-Pugh Poly V design matches directly with the Itoh motorized roller or if an alternate non powered roller motor option is chosen, Ralphs-Pugh can machine Poly V pulleys to your specification.
Ralphs-Pugh Poly V inserts are sold as a component, or as complete rollers.
Available with 2 shaft configurations3PB44J43-4 - 7/16" Hex - Spring loaded through shafts or drilled and tapped ends 5/16-18 x 1.00” deep3PB50J43-4 - 1/2" Round - Drilled and tapped 5/16-18 x 1.00” deep
Safety Considerations: Poly V belts have very little elongation or stretch. Guards or shields should be installed anywhere personnel could come into contact with them due to nip points.
2.50” Roller Tube OD Inserts
• Machined out of Steel or Stainless Steel• Roller center distances start at 3.00”
Insert effective diameter (OD) is dependent on whether final diameter with belt installed must be less than roller tube diameter.
Standard roller tube is 2.50” OD x .120” wall thickness• Insert has 1 ABEC-1 precision ball bearing.• Insert is welded to the tube end for strength and concentricity.
Poly V Belt ConfigurationAccommodates Hutchinson ConveyXonic “J” or “K” belts with up to a maximum of 8 ribs per belt dependent on roller centers and loading – See how to determine in “Application Information Required”.
Standard roller tube is 2.50” OD x .120” wall thickness
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected] phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
2
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
Poly V ProductsPoly V Products
Ralphs-Pugh Poly V design matches directly with the Itoh motorized roller or if an alternate non powered roller motor option is chosen Ralphs-Pugh can machine Poly V pulleys to your specification.
Ralphs-Pugh Poly V inserts are sold as a component, or as complete rollers.
Standard shaft configuration is 11/16” hex, spring loaded or fixed.
Part Number – 34PB68(J or K belt)(Effective Diameter of insert) – Up to 8
Safety considerations: Poly V belts have very little elongation or stretch. Guards or shields should be installed anywhere personnel could come into contact with them due to nip points.
Application Information Required
• Roller center distance• Zone length• Max pallet weight• Footprint of pallet or dimensions of
load to be conveyed
Features of Poly V Inserts and Rollers
1.90” Series• One motorized roller can power up to 30 slave rollers
depending on application criteria• Poly V belts don’t slip or stretch like “O” rings and are
low maintenance• Reduced noise levels• Can be used with robotic picking due to the accuracy
of electronic stopping and starting• Insert diameter with belt installed can be smaller in
diameter than tube OD allowing product to betransferred off the system in both directions.
2.50” Series• Reduced noise levels• Clean – No chains, grease or gear boxes• Close rollers centers - down to 3.00”• Reduced maintenance - no lubrication necessary vs chain and sprocket drive systems• Can be used with robotic picking due to the accuracy of electronic stopping and starting• Tighter roller centers than chain and sprocket configurations• Insert diameter with belt installed can be smaller in diameter than tube OD allowing product to
be transferred off the system in both directions.• Can move pallet loads up to 3300 pounds – dependent on application data and chosen drive
method
• Max load per roller• Max load per zone• Speed of conveyer• Will conveyor be loaded from both sides? This will
determine effective diameter and guarding issues
3
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected] phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
Poly V ProductsPoly V Products
Poly V Belt Inserts - 43MM Effective Diameter
1.69”
1.125”
1.25”
Bearing: Type: Qty:ABEC-1 Precision Chromium 2
Option: ABEC-1 Precision 440SS 2
Insert Material: Conductive Plastic
Bore: 7/16" Hex Part # 3PB44J43-41/2" Round 3PB50J43-4
Tube: 1.90" x .065" - StandardOptions: 1.75" x .065"
2.50" x .083Others
Roller Centers: 3.00" - Standard
Installation method: Press fit into tube and swage
Belts: ConveyXonic® - High Tension Poly V - elastic nylon reinforced rubber# of ribs Series Part #2, 3, 4 "J" Inquire - Dependent on load requirements and roller center distances
Belt Manufacturer: Hutchinson Belt Drive Systems
Belt Supplier: Ralphs-Pugh
Insert Drive Options: Motorized roller - Ralphs-Pugh insert is a direct match to Itoh Denki motorized rollers. Ralphs-Pugh will machine a Poly V pulley for installation with your preferred drive.
3PB44J43-4
.68”0.13”
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected] phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
4
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
Poly V ProductsPoly V Products
Poly V Belt Inserts - 60MM Effective Diameter - 6 Ribs
34PB68J60-6 34PB68K60-6
2.36”
1.82”
1.63”
0.19” 0.50”
Bearing: Type: Qty:ABEC-1 Precision Chromium 1
Option: ABEC-1 Precision 440SS 1
Insert Material: Steel or Stainless Steel
Bore: 11/16" Hex Part # 34PB68J60-6 "J" series belts34PB68K60-6 "K" series belts
Tube: 2.50" OD x .120" wall thickness - StandardOptions: Inquire
Roller Centers: 3.00" - 12.00"
Installation Method: Press fit into tube and weld
Belts: ConveyXonic® - High Tension Poly V - elastic nylon reinforced rubber# of ribs Series Part #2 - 6 "J" Inquire Dependent on load requirements and roller center distances2 - 6 "K" Inquire Dependent on load requirements and roller center distances
Belt Manufacturer: Hutchinson Belt Drive Systems
Belt Supplier: Ralphs-Pugh
Insert Drive Options: Motorized roller or Ralphs-Pugh will machine a Poly V pulley for installation with your preferreddrive.
2.36”
0.19”
2.19”
2.38”
0.50”
5
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected] phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
Poly V ProductsPoly V Products
Poly V Belt Inserts - 60MM Effective Diameter - 8 Ribs
34PB68K60-834PB68J60-8
Bearing: Type: Qty:ABEC-1 Precision Chromium 1
Option: ABEC-1 Precision 440SS 1
Insert Material: Steel or Stainless Steel
Bore: 11/16" Hex Part # 34PB68J60-8 "J" series belts34PB68K60-8 "K" series belts
Tube: 2.50" OD x .120" wall thickness - StandardOptions: Inquire
Roller Centers: 3.00" - 12.00"
Installation Method: Press fit into tube and weld
Belts: ConveyXonic® - High Tension Poly V - elastic nylon reinforced rubber# of ribs Series Part #2 - 8 "J" Inquire Dependent on load requirements and roller center distances2 - 8 "K" Inquire Dependent on load requirements and roller center distances
Belt Manufacturer: Hutchinson Belt Drive Systems
Belt Supplier: Ralphs-Pugh
Insert Drive Options: Motorized roller - Ralphs-Pugh insert is a direct match to Itoh Denki motorized rollers. Ralphs-Pugh will machine a Poly V pulley for installation with your preferred drive.
2.36”
2.19”
2.00”
0.19” 0.20”
2.36”
0.50”0.50”
2.75”
2.94”
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected] phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
6
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
Poly V ProductsPoly V Products
1.90” O.D. Poly V Belt Roller - 3PB44J43-4.G46.C68
1.69”
1.13”1.25”
Bearing: Type: Qty:ABEC-1 Precision Chromium 2
Option: ABEC-1 Precision 440SS 2
Insert Material: Conductive Plastic
Bore: 7/16" Hex Part # 3PB44J43-4
Tube: 1.90" x .065" - Standard
Roller Centers: 3.00" - Standard
Installation method: Press fit into tube and swage
Belts: ConveyXonic® - High Tension Poly V - elastic nylon reinforced rubber# of ribs Series Part #2, 3, 4 "J" Inquire - Dependent on load requirements and roller center distances
Belt Manufacturer: Hutchinson Belt Drive Systems
Belt Supplier: Ralphs-Pugh
Drive Options: Motorized roller - Ralphs-Pugh insert is a direct match to Itoh Denki motorized rollers. Ralphs-Pugh can machine Poly V pulleys to your specifications for non motorized roller drive options.
FrameI.F.
FrameI.F.Load Capacity (lbs.) Load Capacity (lbs.)
12 297 33 9515 228 36 8718 185 39 8021 156 42 7424 134 45 6927 118 48 6430 105 51 60
Load Capacity
* Load capacity with aluminum tube or shaft is 33% of steel capacity.** Longer lengths are available upon request.
*** Capacities are for uniform loading - Reduce 50% for point loading.
OA
SL0.13”
7
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected] phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
Poly V ProductsPoly V Products
Bearing: Type: Qty:ABEC-1 Precision Chromium 1
Option: ABEC-1 Precision 440SS 1
Insert Material: Steel or Stainless Steel
Bore: 11/16" Hex Part # 34PB68J60-6 "J" series belts
Tube: 2.50" OD x .120" wall thickness - StandardOptions: Inquire
Roller Centers: 3.00" - 12.00"Options: Inquire
Installation Method: Press fit into tube and weld
Belts: ConveyXonic® - High Tension Poly V - elastic nylon reinforced rubber# of ribs Series Part #2 - 6 "J" Inquire - Dependent on load requirements and roller center distances
Belt Manufacturer: Hutchinson Belt Drive Systems
Belt Supplier: Ralphs-Pugh
Drive Options: Motorized roller - Ralphs-Pugh insert is a direct match to Itoh Denki motorized rollers. Ralphs-Pughcan machine Poly V pulleys to your specifications for non motorized roller drive options.
2.50” O.D. 6 Rib Poly V “J” Series Belt Roller - 34PB68J60-6.G56.C82
FrameI.F.
FrameI.F.Load Capacity (lbs.) Load Capacity (lbs.)
12 1000 33 75915 1000 36 69018 1000 39 63121 1000 42 58124 1000 45 53827 947 48 50130 843 51 467
Load Capacity
* Load capacity with aluminum tube or shaft is 33% of steel capacity.** Longer lengths are available upon request.
*** Capacities are for uniform loading - Reduce 50% for point loading.
2.36”
1.82”1.63”
0.19”
OA
SL
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected] phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
8
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
Poly V ProductsPoly V Products
Bearing: Type: Qty:ABEC-1 Precision Chromium 1
Option: ABEC-1 Precision 440SS 1
Insert Material: Steel or Stainless Steel
Bore: 11/16" Hex Part # 34PB68K60-6 "K" series belts
Tube: 2.50" OD x .120" wall thickness - StandardOptions: Inquire
Roller Centers: 3.00" - 12.00"Options: Inquire
Installation Method: Press fit into tube and weld
Belts: ConveyXonic® - High Tension Poly V - elastic nylon reinforced rubber# of ribs Series Part #2 - 6 "K" Inquire - Dependent on load requirements and roller center distances
Belt Manufacturer: Hutchinson Belt Drive Systems
Belt Supplier: Ralphs-Pugh
Drive Options: Motorized roller - Ralphs-Pugh insert is a direct match to Itoh Denki motorized rollers. Ralphs-Pughcan machine Poly V pulleys to your specifications for non motorized roller drive options.
2.19”2.38”
2.36”
0.19”
2.50” O.D. 6 Rib Poly V “K” Series Belt Roller - 34PB68K60-6.G56.C82
FrameI.F.
FrameI.F.Load Capacity (lbs.) Load Capacity (lbs.)
12151821242730
Load Capacity
1000 33 7591000 36 6901000 39 6311000 42 5811000 45 538947 48 501843 51 467
OA
SL
9
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected] phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
Poly V ProductsPoly V Products
Bearing: Type: Qty:ABEC-1 Precision Chromium 1
Option: ABEC-1 Precision 440SS 1
Insert Material: Steel or Stainless Steel
Bore: 11/16" Hex Part # 34PB68J60-8 "J" series belts
Tube: 2.50" OD x .120" wall thickness - StandardOptions: Inquire
Roller Centers: 3.00" - 12.00"Options: Inquire
Installation Method: Press fit into tube and weld
Belts: ConveyXonic® - High Tension Poly V - elastic nylon reinforced rubber# of ribs Series Part #2 - 8 "J" Inquire - Dependent on load requirements and roller center distances
Belt Manufacturer: Hutchinson Belt Drive Systems
Belt Supplier: Ralphs-Pugh
Drive Options: Motorized roller - Ralphs-Pugh insert is a direct match to Itoh Denki motorized rollers. Ralphs-Pughcan machine Poly V pulleys to your specifications for non motorized roller drive options.
2.50” O.D. 8 Rib Poly V “J” Series Belt Roller - 34PB68J60-8.G56.C82
FrameI.F.
FrameI.F.Load Capacity (lbs.) Load Capacity (lbs.)
12 1000 33 75915 1000 36 69018 1000 39 63121 1000 42 58124 1000 45 53827 947 48 50130 843 51 467
Load Capacity
* Load capacity with aluminum tube or shaft is 33% of steel capacity.** Longer lengths are available upon request.
*** Capacities are for uniform loading - Reduce 50% for point loading.
2.36”
2.19”2.00”
0.19”OA
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected] phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
10
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
Poly V ProductsPoly V Products
Bearing: Type: Qty:ABEC-1 Precision Chromium 1
Option: ABEC-1 Precision 440SS 1
Insert Material: Steel or Stainless Steel
Bore: 11/16" Hex Part # 34PB68K60-8 "K" series belts
Tube: 2.50" OD x .120" wall thickness - StandardOptions: Inquire
Roller Centers: 3.00" - 12.00"Options: Inquire
Installation Method: Press fit into tube and weld
Belts: ConveyXonic® - High Tension Poly V - elastic nylon reinforced rubber# of ribs Series Part #2 - 8 "K" Inquire - Dependent on load requirements and roller center distances
Belt Manufacturer: Hutchinson Belt Drive Systems
Belt Supplier: Ralphs-Pugh
Drive Options: Motorized roller - Ralphs-Pugh insert is a direct match to Itoh Denki motorized rollers. Ralphs-Pughcan machine Poly V pulleys to your specifications for non motorized roller drive options.
2.50” O.D. 8 Rib Poly V “K” Series Belt Roller - 34PB68K60-8.G56.C82
FrameI.F.
FrameI.F.Load Capacity (lbs.) Load Capacity (lbs.)
12151821242730
Load Capacity
1000 33 7591000 36 6901000 39 6311000 42 5811000 45 538947 48 501843 51 467
0.20”
2.36”
2.94”
2.75”
OA
11
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected] phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
Cantilever RollersCantilever Rollers
Ralphs-Pugh Cantilever Rollers - Plastic and Metal Tubes
Ralphs-Pugh cantilever rollers are available in many combinations of bearings, shafts and tube materials. We offer cantilever rollers for both gravity and powered applications. Cantilevered rollers are unique in that one end of the roller is capped preventing any type of contamination from reaching the bearing. The opposite end has an extended fixed shaft that can be threaded or standard finish. Typical applications are vertical guide rollers and belt guides.
Plastic Cantilever Roller Information:
Materials:
Tubes:• Standard white PVC• “Hi-Impact” white PVC with UV stabilizers
Drive Options: Grooves
Special Options:• Plastic tube can be internally steel reinforced
Shaft Materials:• Carbon Steel• Stainless Steel• Aluminum• Zinc and Nickel Plating Available
Shaft Configurations / Options:• Hex, Round• Threaded or Standard Finish
Bearings:
Commercial Grade Ball Bearings:
Steel and Stainless Steel with or without labyrinth seal systems on the extended shaft end depending on tube configuration.
ABEC-1 Precision Bearings:
Chromium alloy steel or Stainless Steel ball bearings in a plastic housing, with a labyrinth seal system on the extended shaft end.
Stainless Steel with or without labyrinth seal systemson the extended shaft end depending on tube configuration.
plastic housing, with a labyrinth seal system on the extended shaft end.
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected] phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
12
phone: 800-486-0021 • fax: 800-995-3942 • www.ralphs-pugh.com • email: [email protected]
Cantilever RollersCantilever Rollers
Metal Cantilever Roller Information:
Materials:
Tubes:• Carbon Steel, Galvanized Steel,
Stainless Steel, Aluminum
Tubes Finishes:• Zinc and Nickel Plating• Anodizing• Polished• Electropolished• Passivated
Drive Options:• Grooves
Cover Options:• Urethane Sleeves• HDPE• UHMW• PVC
Shaft Materials:• Carbon Steel• Stainless Steel• Aluminum• Zinc and Nickel Plating Available
Shaft Configurations / Options:• Hex, Round• Threaded or Standard Finish