POLY-GLASS 320 CLEAR COATINGS - Absolute Resurfacing
3
Absolute Resurfacing Pty Ltd ABN 81 120 592 092 48 / 215 Brisbane Road Ph 0433 640 353 Biggera Waters, QLD, 4216 [email protected] PO Box 3124, Helensvale Town Centre, QLD 4212 www.absoluteresurfacing.com.au Page 1 of 1 POLY-GLASS 320 CLEAR COATINGS Poly-Glass Clear comes in 3 finishes High Gloss Low Gloss (Satin) Ultra-Low Gloss (Matte) The Poly-Glass clear can be applied over the top of • Napco Flintstone 2 coating • Other Napco Poly-Glass coatings (altering the gloss level) • Napco High Build Primer coating A greener, VOC compliant coating that allows the customer to “shower in 2 hours” after you refinish their bathtub. Poly-Glass® 320 is legal and compliant with USA’s Californian government’s stricter volatile organic compound (VOC) regulation, there’s no other coating in the refinishing industry that can compare with Poly-Glass® 320’s performance, ease of use and quick turnaround time. You can now advertise you use a new, greener coating. It is Californian VOC compliant and is a much better and safer coating for the environment. Some other advantages are: • Lower odor dissipating faster means fewer complaints from your customers. • 50% greater impact resistance than other refinishing coatings means happier customers because this coating will wear better and last longer. • Higher gloss when applied correctly. • Dry to the touch in 4-6 minutes at room temperature means the coating is less vulnerable to dust and imperfections than other coatings and also less likely to run. It also means you can apply another coat quicker, which shortens time on the job. • Remove masking paper and caulk sooner than other coatings. • Put the fixture back in service in 2 hours at normal room temperature. Your customers will love this feature. • Using an infrared heat lamp cures the coating in as little as 30 minutes
Transcript of POLY-GLASS 320 CLEAR COATINGS - Absolute Resurfacing
Absolute Resurfacing Pty Ltd ABN 81 120 592 092 48 / 215 Brisbane Road Ph 0433 640 353 Biggera Waters, QLD, 4216 [email protected] PO Box 3124, Helensvale Town Centre, QLD 4212 www.absoluteresurfacing.com.au
Page 1 of 1
POLY-GLASS 320 CLEAR COATINGS
Poly-Glass Clear comes in 3 finishes High Gloss Low Gloss (Satin) Ultra-Low Gloss (Matte)
The Poly-Glass clear can be applied over the top of
• Napco Flintstone 2 coating • Other Napco Poly-Glass coatings (altering the gloss level) • Napco High Build Primer coating
A greener, VOC compliant coating that allows the customer to “shower in 2 hours” after you refinish their bathtub.
Poly-Glass® 320 is legal and compliant with USA’s Californian government’s stricter volatile organic compound (VOC) regulation, there’s no other coating in the refinishing industry that can compare with Poly-Glass® 320’s performance, ease of use and quick turnaround time . You can now advertise you use a new, greener coating. It is Californian VOC compliant and is a much better and safer coating for the environment. Some other advantages are:
• Lower odor dissipating faster means fewer complaints from your customers. • 50% greater impact resistance than other refinishing coatings means happier customers
because this coating will wear better and last longer. • Higher gloss when applied correctly. • Dry to the touch in 4-6 minutes at room temperature means the coating is less vulnerable
to dust and imperfections than other coatings and also less likely to run. It also means you can apply another coat quicker, which shortens time on the job.
• Remove masking paper and caulk sooner than other coatings. • Put the fixture back in service in 2 hours at normal room temperature. Your customers
will love this feature. • Using an infrared heat lamp cures the coating in as little as 30 minutes
Features Fast drying – “shower in just 2 hours” with the Mega-Fast version
Easy to apply with excellent flow and leveling
Resistant to staining with common household chemicals
Excellent gloss and Color retention
30% lower VOC content
Sand after 20 minutes with use of a heat lamp
Buff after 20 minutes with use of a heat lamp
Greener /Healthier – Low toxicity/ lower VOC content
Better for the environment - Does not deplete the ozone layer
Low odor
Summary NAPCO Poly-Glass ® 320 Low VOC has very good early
hardness and water resistance, as well as excellent performance in
dry to tape and cross-hatch adhesion tests. The product is both
strong and durable without sacrificing flexibility. It has beautiful
initial gloss with perfect gloss retention in Q.U.V. weather testing.
The solvent has a long pot-life and is easily stored under normal
conditions. With low Volatile Organic Compounds (VOC), the
NAPCO Poly-Glass® 320 Low VOC is safe, reliable, and fast
curing.
7315 Hamlin Av
Skokie, IL 60076
1-800-888-1081
May Be Applied To: Porcelain
Ceramic
Acrylic
Fiberglass
Plastic
PVC
Laminate Surfaces
Marble
Granite
Metal
Wood
Recommended Surface Preparation
Porcelain & Enamel Remove all caulk, clean surface with
NAPCO Poly cleaner and rinse with cool
water, dry the surface and apply etch, after
10 - 15 min rinse etch down the drain with
cool water, wet sand the etch residue with
80 grit paper, apply 2 light coats of Low
VOC Epoxy Primer.
Ceramic Remove all caulk, clean surface
with NAPCO poly cleaner, rinse
with cool water, dry surface, apply
NAPCO Poly Bond Primer Fiberglass & Acrylic Remove all caulk, clean with NAPCO
Poly Cleaner, rinse with cool water, wet
sand horizontal surfaces with 120 sand
paper and vertical surfaces with 220, rinse
with cool water and dry entire surface.
Wood Remove caulk, clean with TSP or liquid
dishwashing liquid and a 3M scrub pad to
remove and kitchen grease, rinse with cool
water, wet sand with 220,rince with cool
water and dry. Apply NAPCO Low VOC
primer.
Metal Remove all caulk, clean with NAPCO
NAPCO POLY-GLASS® 320 Low VOC A high performance coating that is applied with greater ease in less time
A durable coating that offers tough chemical resistance
NAPCO POLY-GLASS® 320 Low VOC A high performance coating that is applied with greater ease in less time
A durable coating that offers tough chemical resistance
Reagent Concentrated Immersion Tests Acids
Sulphuric 5% No Effect – 3 ½ years
Phosphoric 50% No Effect-3 ½ years
Hydrochloric 10% Slight Loss of Gloss- 3 ½ years
Hydrochloric 15% Slight Loss of Gloss- 3 ½ years
Hydrochloric 28% Failed - 48 hours
Hydrochloric 38% Failed - 18 hours
Acetic 5% Failed - 40 days
Acetic 10% Failed - 14 days
Acetic 50% Failed - 10 days
Sodium Hydroxide No Test Data Available
Ammonia No Test Data Available
Miscellaneous Detergent 5% No Effect – 3 ½ years
Detergent 5% No Effect – 7 hours at 100°C
Distilled Water No Effect – 1,000 hours
100% Humidity Slight Blistering – 1,000 hours @ 100°F
Dust Free Mega-fast 8 to 10 mins
Quick Dry 10 to 12 mins
Regular Dry 12 to 14 mins
Water Resistance Mega-fast 2 hrs
Quick Dry 24 hrs
Regular Dry 48hrs
Sandable Mega-fast 2 hrs (20 minutes with use of heat lamp)
Quick Dry 24hrs
Regular Dry 48hrs
Accelerated Weathering Tests Q.U.V 60 Gloss Initial Gloss- 85%
1000 Hours- Final Gloss 85%
Q.U.V Resistance to change @ 1000 Hours: very
high
Miscellaneous Tests Cross Hatch Adhesion No Failures (4 to 5A)
MEK Resistance 25 Double Rub - Pass
Generic Type Light Fast Aliphatic Urethane
Gloss 85-90% on a 60-degree head; 18% for Low Gloss Resin
Solids 69% +/- 1% by Weight; 55% +/- 1% by Volume; 41% at Spray Viscosity
Weight/Gallon 10.75 +/- 0.1 lbs.
Pencil Hardness 4H – Slight Mark, No Film Break
Theoretical Coverage 864 sq. ft. per 1 mil Dry Coating (catalyzed & reduced resin)
Flash Point 39.2ûF
Viscosity-Reduced 20-24 Seconds #2 Zahn Cup @ 2 to 1 to 1
Spray Viscosity 18-22 seconds #2 Zahn Cup, depending on colors.
Application Apply with HVLP spray system, air brush, or natural bristle brush
Application Thickness 2.5 to 3.5 mils dry (1 tack coat + 2 wet coats)
Mixing Instructions 2 parts Poly-Glass base to 1 part Poly-Glass catalyst to 1 part Poly-Glass thinner by
volume
Drying Schedule Consult resin label
Pot Life Approximately 2 hours for mixed, catalyzed, and reduced material
Storage Stability 1-year minimum when stored between 55-100ûF
Equipment Cleanup NAPCO Overspray Gun Cleaner
Safety Refer to Material Data Safety Sheets (MSDS) for proper equipment and handling
Bonderite *1000 Treated, Cold Rolled Steel Tests Acrylic Drop Flex Pass 12lbs. 30X weekly for 90 days
Flexibility ¼ in..Mandel Passes-No cracks
Direct Impact Pass 60in lbs. at 1-mil dry film
Substrate Bonderite *1000 24-Hour Spot Tests Xylol Slight Ring Mark
Cellusolve Acetate Slight Ring Mark – No Softening
Cyclohexanone Moderate Ring Mark – Slight Softening
5% Sulfuric Acids No effect
30% Sulfuric Acids Film Slightly Dulled
50% Sulfuric Acids Film Dulled
10% Hydrochloric No Effect
1% Iodine Moderate Stain
5% Potassium Permanganate Moderate Stain
409 No Effect
Ajax Liquid Soap w/ lemon No Effect
Black hair dye Stain
Catsup No Effect
CLR No Effect
Clorox Bleach No Effect
Dow Scrubbing Bubbles No Effect
Drano No Effect
Hair Color Moderate Stain
Hydrogen Peroxide No Effect
Laundry Detergent No Effect
Lipstick No Effect
Lysol Disinfectant No Effect
Marker Pen No Effect
Mustard Very Slight Stain
Soft Scrub No Effect
Tilex No Effect
Windex w/ Ammonia No Effect
Nail Polis Remover/ Acetone No Effect
Konig Hardness Test Unexposed 120
Exposed 73
Post 24 Hour Recovery Period 123
Technical Performance Report Evonik Industries 10/17/08
