po box assembly · Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C. © 2008 Hewlett-Packard...

6
Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C. © 2008 Hewlett-Packard Company hp.com/go/activitycenter Kung Fu Po Takeout Kit Box ASSEMBLY INSTRUCTIONS Time to Complete: Approximately 30 minutes Level: Medium GETTING STARTED Materials: • Metal-edged ruler • Butter knife • Scissors or X-ACTO knife • Cutting mat (optional) • Multipurpose glue • Hole punch • Ribbon for handle (optional) 1. Score all the pieces: Using a ruler as a guide, run the back side of a butter knife along the dotted lines. 2. Using scissors or an X-ACTO knife and cutting mat, cut out pieces on solid lines. Also cut slits on top flaps. ASSEMBLE YOUR BOX 3. Fold up all sides. Then fold side flaps (1) inward. 4. Dab glue on the underside of flap, and press onto printed side of panel A (2). Repeat on other flap, so that two flaps overlap slightly. Repeat on other side of box. 5. Using a hole punch, make a small hole on both sides of box, where flaps meet. 6. String ribbon or wire through the holes, and knot the ends on the inside.

Transcript of po box assembly · Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C. © 2008 Hewlett-Packard...

Page 1: po box assembly · Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C. © 2008 Hewlett-Packard Company hp.com/go/activitycenter Kung Fu Po Takeout Kit Box ASSEMBLY INSTRUCTIONS

Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C.

© 2008 Hewlett-Packard Company hp.com/go/activitycenter

Kung Fu Po Takeout Kit

Box ASSEMBLY INSTRUCTIONS Time to Complete: Approximately 30 minutes Level: Medium

GETTING STARTED

Materials:

• Metal-edged ruler

• Butter knife • Scissors or X-ACTO knife • Cutting mat (optional)

• Multipurpose glue • Hole punch • Ribbon for handle (optional)

1. Score all the pieces: Using a ruler as a guide, run the back side of a butter knife along the dotted lines.

2. Using scissors or an X-ACTO knife and cutting mat, cut out pieces on solid lines. Also cut slits on top flaps.

ASSEMBLE YOUR BOX

3. Fold up all sides. Then fold side flaps (1) inward.

4. Dab glue on the underside of flap, and press onto printed side of panel A (2). Repeat on other flap, so that two flaps overlap slightly. Repeat on other side of box.

5. Using a hole punch, make a small hole on both sides of box, where flaps meet.

6. String ribbon or wire through the holes, and knot the ends on the inside.

Page 2: po box assembly · Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C. © 2008 Hewlett-Packard Company hp.com/go/activitycenter Kung Fu Po Takeout Kit Box ASSEMBLY INSTRUCTIONS

Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C.

© 2008 Hewlett-Packard Company hp.com/go/activitycenter

7. Fold down non-interlocking top pieces. Fold down and join interlocking top pieces.

8. Your takeout box is done!

Page 3: po box assembly · Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C. © 2008 Hewlett-Packard Company hp.com/go/activitycenter Kung Fu Po Takeout Kit Box ASSEMBLY INSTRUCTIONS

Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C.© 2008 Hewlett-Packard Company

hp.com/go/activitycenter

KUNG FU PO TAKEOUT KIT - BOX

SIDE FLAP (1)

PAN

EL

A (2

)

PANEL A (2)

SID

E FL

AP

(1)

SIDE FLAP (1)

SIDE FLA

P (1)

This project created for youat the Hewlett-Packard Activity Center

www.hp.com/go/activitycenter

Page 4: po box assembly · Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C. © 2008 Hewlett-Packard Company hp.com/go/activitycenter Kung Fu Po Takeout Kit Box ASSEMBLY INSTRUCTIONS

Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C.

© 2008 Hewlett-Packard Company hp.com/go/activitycenter

Kung Fu Po Takeout Kit

Cookie ASSEMBLY INSTRUCTIONS Time to Complete: Approximately 15 minutes Level: Medium

GETTING STARTED

Materials;

• Metal-edged ruler

• Butter knife • Scissors or X-ACTO knife • Cutting mat (optional)

1. Score all the pieces: Using a ruler as a guide, run the back side of a butter knife along the dotted lines.

2. Using scissors or an X-ACTO knife and cutting mat, cut along solid lines.

ASSEMBLE THE COOKIE

3. Fold paper circle in half, patterned sides together, and create a good crease. Unfold.

4. Hold the paper so that the patterned side faces up, and turn the paper so that the crease is vertical.

5. Gently fold circle together, lining up the crease so that each side is even, but DO NOT crease in the center at this time.

6. Place the fortune strip in the middle of the fortune cookie.

Page 5: po box assembly · Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C. © 2008 Hewlett-Packard Company hp.com/go/activitycenter Kung Fu Po Takeout Kit Box ASSEMBLY INSTRUCTIONS

Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C.

© 2008 Hewlett-Packard Company hp.com/go/activitycenter

7. Holding the edges together, place a finger in the center of the crease pull the sides of the cookie downward. Continue until both sides of the cookie touch.

8. Your fortune cookie is ready!

Page 6: po box assembly · Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C. © 2008 Hewlett-Packard Company hp.com/go/activitycenter Kung Fu Po Takeout Kit Box ASSEMBLY INSTRUCTIONS

Kung Fu Panda ™ & © 2008 DreamWorks Animation L.L.C.© 2008 Hewlett-Packard Company

hp.com/go/activitycenter

KUNG FU PO TAKEOUT KIT - COOKIE