PN-L602BLCD MONITOR

OPERATION MANUAL

IMPORTANT:To aid reporting in case of loss or theft, please record the product’s model and serial numbers in the space provided. The numbers are located in the rear of the product.

Model No.:

Serial No.:

U.S.A. ONLY

FOR CUSTOMERS IN U.K.IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:GREEN-AND-YELLOW: EarthBLUE: NeutralBROWN: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

•ThewirewhichiscolouredGREEN-AND-YELLOWmustbeconnectedtotheterminalintheplugwhichismarkedbytheletter E or by the safety earth orcolouredgreenorgreen-and-yellow.

•ThewirewhichiscolouredBLUEmustbeconnectedtotheterminalwhichismarkedwiththeletterN or coloured black.•ThewirewhichiscolouredBROWNmustbeconnectedtotheterminalwhichismarkedwiththeletterL or coloured red.

Ensurethatyourequipmentisconnectedcorrectly.Ifyouareinanydoubtconsultaqualifiedelectrician.“WARNING: THIS APPARATUS MUST BE EARTHED.”

3 E

IMPORTANT INFORMATION

WARNING: TOREDUCETHERISKOFFIREORELECTRICSHOCK,DONOTEXPOSETHISPRODUCTTORAINORMOISTURE.

RISKOFELECTRICSHOCKDONOTOPEN

CAUTION

CAUTION: TOREDUCETHERISKOFELECTRICSHOCK,DONOTREMOVECOVER. NOUSER-SERVICEABLEPARTSINSIDE. REFERSERVICINGTOQUALIFIEDSERVICEPERSONNEL.

Thelightningflashwitharrowheadsymbol,withinanequilateraltriangle,isintendedtoalerttheuser to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may beofsufficientmagnitudetoconstituteariskofelectric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING: FCCRegulationsstatethatanyunauthorizedchangesormodificationstothisequipmentnotexpresslyapprovedbythemanufacturercouldvoidtheuser’sauthoritytooperatethisequipment.

NOTE:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforClassAdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferencewhentheequipmentisoperatedinacommercialenvironment.Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnot installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operationofthisequipmentinaresidentialareaislikelytocauseharmfulinterferenceinwhichcasetheuserwillberequiredto correct the interference at his own expense.

ThisproductutilizesaCRcoinLithiumbatterywhichcontainsaPerchloratematerial.Special handling for this material may apply,Californiaresidents,Seewww.dtsc.ca.gov/hazardouswaste/perchlorate/Others,consultlocalenvironmentalofficers.

U.S.A. ONLY

4E

IMPORTANT INFORMATION (Continued)

A. Information on Disposal for Users (private households)1. In the European UnionAttention:Ifyouwanttodisposeofthisequipment,pleasedonotusetheordinarydustbin!

Usedelectricalandelectronicequipmentmustbetreatedseparatelyandinaccordancewithlegislationthatrequirespropertreatment,recoveryandrecyclingofusedelectricalandelectronicequipment.Followingtheimplementationbymemberstates,privatehouseholdswithintheEUstatesmayreturntheirusedelectricalandelectronicequipmenttodesignatedcollectionfacilitiesfreeofcharge*.Insomecountries*yourlocalretailermayalsotakeback your old product free of charge if you purchase a similar new one.

*)Pleasecontactyourlocalauthorityforfurtherdetails.

Ifyourusedelectricalorelectronicequipmenthasbatteriesoraccumulators,pleasedisposeoftheseseparatelybeforehandaccordingtolocalrequirements.

Bydisposingofthisproductcorrectlyyouwillhelpensurethatthewasteundergoesthenecessarytreatment,recoveryandrecycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due to inappropriate waste handling.

2. In other Countries outside the EUIf you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.

ForSwitzerland:Usedelectricalorelectronicequipmentcanbereturnedfreeofchargetothedealer,evenifyoudon’tpurchaseanewproduct.Furthercollectionfacilitiesarelistedonthehomepageofwww.swico.chorwww.sens.ch.

B. Information on Disposal for Business Users1. In the European UnionIf the product is used for business purposes and you want to discard it:

PleasecontactyourSHARPdealerwhowillinformyouaboutthetake-backoftheproduct.Youmightbechargedforthecostsarisingfromtake-backandrecycling.Smallproducts(andsmallamounts)mightbetakenbackbyyourlocalcollectionfacilities.

ForSpain:Pleasecontacttheestablishedcollectionsystemoryourlocalauthorityfortake-backofyourusedproducts.

2. In other Countries outside the EUIf you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.

Attention: Your product is marked with this symbol. It means that used electrical and electronic products should not be mixed with general household waste. There is a separate collection system for these products.

The battery supplied with this product contains traces of Lead.ForEU:Thecrossed-outwheeledbinimpliesthatusedbatteriesshouldnotbeputtothegeneralhouseholdwaste!Thereisaseparatecollectionsystemforusedbatteries,toallowpropertreatmentandrecyclinginaccordance with legislation. Please contact your local authority for details on the collection and recycling schemes.

ForSwitzerland:The used battery is to be returned to the selling point.

Forothernon-EUcountries:Please contact your local authority for correct method of disposal of the used battery.

“BATTERYDISPOSAL”THISPRODUCTCONTAINSALITHIUMPRIMARY(MANGANESSDIOXIDE)MEMORYBACK-UPBATTERYTHATMUSTBEDISPOSEDOFPROPERLY.PLEASECONTACTYOURLOCALSHARPDEALERORAUTHORIZEDSERVICEREPRESENTATIVEFORASSISTANCEINDISPOSINGOFTHISBATTERY.

U.S.A.ANDCANADAONLY

EUONLY

EUONLY

5 E

ThankyouforyourpurchaseofaSHARPLCDproduct.Toensuresafetyandmanyyearsoftrouble-freeoperationofyourproduct, please read the Safety Precautions carefully before using this product.

SAFETY PRECAUTIONSElectricityisusedtoperformmanyusefulfunctions,butitcanalsocausepersonalinjuriesandpropertydamageifimproperlyhandled.Thisproducthasbeenengineeredandmanufacturedwiththehighestpriorityonsafety.However,improperusecanresultinelectricshockand/orfire.Inordertopreventpotentialdanger,pleaseobservethefollowinginstructionswheninstalling,operatingandcleaningtheproduct.ToensureyoursafetyandprolongtheservicelifeofyourLCDproduct,pleasereadthefollowing precautions carefully before using the product. 1. Readinstructions—Alloperatinginstructionsmustbereadandunderstoodbeforetheproductisoperated. 2. Keepthismanualinasafeplace—Thesesafetyandoperatinginstructionsmustbekeptinasafeplaceforfuture

reference. 3. Observewarnings—Allwarningsontheproductandintheinstructionsmustbeobservedclosely. 4. Followinstructions—Alloperatinginstructionsmustbefollowed. 5. Cleaning—UnplugthepowercordfromtheACoutletbeforecleaningtheproduct.Useadryclothtocleantheproduct.Do

notuseliquidcleanersoraerosolcleaners. 6. Attachments—Donotuseattachmentsnotrecommendedbythemanufacturer.Useofinadequateattachmentscanresult

in accidents. 7. Waterandmoisture—Donotusetheproductnearwater.Donotinstalltheproductinaplacewherewatermaysplashonto

it.Becarefulofequipmentwhichdrainswatersuchasanair-conditioner. 8. Ventilation—Theventsandotheropeningsinthecabinetaredesignedforventilation. Donotcoverorblocktheseventsandopeningssinceinsufficientventilationcancauseoverheatingand/orshortenthelife

oftheproduct.Donotplacetheproductonasofa,rugorothersimilarsurface,sincetheycanblockventilationopenings.Donotplacetheproductinanenclosedplacesuchasabookcaseorrack,unlessproperventilationisprovidedorthemanufacturer’s instructions are followed.

9. Powercordprotection—Thepowercordsmustberoutedproperlytopreventpeoplefromsteppingonthemorobjectsfromresting on them.

10. Thescreenusedinthisproductismadeofglass.Therefore,itcanbreakwhentheproductisdroppedorappliedwithimpact.Becarefulnottobeinjuredbybrokenglasspiecesincasethescreenbreaks.

11. Overloading—DonotoverloadACoutletsorextensioncords.Overloadingcancausefireorelectricshock.12. Enteringofobjectsandliquids—Neverinsertanobjectintotheproductthroughventsoropenings.Highvoltageflowsin

theproduct,andinsertinganobjectcancauseelectricshockand/orshortinternalparts. Forthesamereason,donotspillwaterorliquidontheproduct.13. Servicing—Donotattempttoservicetheproductyourself.Removingcoverscanexposeyoutohighvoltageandother

dangerousconditions.Requestaqualifiedservicepersontoperformservicing.14. Repair—Ifanyofthefollowingconditionsoccurs,unplugthepowercordfromtheACoutlet,andrequestaqualifiedservice

person to perform repairs. a.Whenthepowercordorplugisdamaged. b.Whenaliquidwasspilledontheproductorwhenobjectshavefallenintotheproduct. c. Whentheproducthasbeenexposedtorainorwater. d.Whentheproductdoesnotoperateproperlyasdescribedintheoperatinginstructions. Donottouchthecontrolsotherthanthosedescribedintheoperatinginstructions.Improperadjustmentofcontrols

notdescribedintheinstructionscancausedamage,whichoftenrequiresextensiveadjustmentworkbyaqualifiedtechnician.

e.Whentheproducthasbeendroppedordamaged. f. Whentheproductdisplaysanabnormalcondition.Anynoticeableabnormalityintheproductindicatesthattheproduct

needs servicing.15. Replacementparts—Incasetheproductneedsreplacementparts,makesurethattheservicepersonusesreplacement

partsspecifiedbythemanufacturer,orthosewiththesamecharacteristicsandperformanceastheoriginalparts.Useofunauthorizedpartscanresultinfire,electricshockand/orotherdanger.

16. Safetychecks—Uponcompletionofserviceorrepairwork,requesttheservicetechniciantoperformsafetycheckstoensure that the product is in proper operating condition.

17. Wallmounting—Whenmountingtheproductonawall,besuretoinstalltheproductaccordingtothemethodrecommended by the manufacturer.

18. Heatsources—Keeptheproductawayfromheatsourcessuchasradiators,heaters,stovesandotherheat-generatingproducts(includingamplifiers).

DEAR SHARP CUSTOMER

6E

SAFETY PRECAUTIONS (Continued)

19. Batteries—Incorrectuseofbatteriesmaycausethebatteriestoburstorignite.Aleakybatterymaycorrodetheequipment,dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:

•Usethespecifiedbatteriesonly. •Installthebatterieswithdueattentiontotheplus(+)andminus(-)sidesofthebatteriesaccordingtotheinstructionsinthe

compartment. •Donotmixoldandnewbatteries. •Donotmixbatteriesofdifferenttypes.Voltagespecificationsofbatteriesofthesameshapemayvary. •Replaceanexhaustedbatterywithanewonepromptly. •Ifyouwillnotusetheremotecontrolforalongtime,removethebatteries. •Ifleakedbatteryfluidgetsonyourskinorclothing,rinseimmediatelyandthoroughly.Ifitgetsintoyoureye,batheyour

eyewellratherthanrubbingandseekmedicaltreatmentimmediately.Leakedbatteryfluidthatgetsintoyoureyeoryourclothing may cause a skin irritation or damage your eye.

20. Usageofthemonitormustnotbeaccompaniedbyfatalrisksordangersthat,couldleaddirectlytodeath,personalinjury,severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and missile launch control in a weapon system.

21. Donotstayincontactwiththepartsoftheproductthatbecomehotforlongperiodsoftime.Doingsomayresultin low-temperatureburns.

WARNING:This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be requiredtotakeadequatecountermeasures.

TomaintaincompliancewithEMCregulations,useshieldedcablestoconnecttothefollowingterminals:PC/AVDVI-Doutputterminal,PC/AVDVI-Dinputterminal,PC/AVHDMIinputterminal,PCD-SUBinputterminal,PCRGBinputterminals,andRS-232Cinput/outputterminals.

Ifamonitorisnotpositionedinasufficientlystablelocation,itcanbepotentiallyhazardousduetofalling.Manyinjuries,particularly to children, can be avoided by taking simple precautions such as:•Usingfixingdeviceslikewallmountbracketsrecommendedbythemanufacturer.•Onlyusingfurniturethatcansafelysupportthemonitor.•Ensuringthemonitorisnotoverhangingtheedgeofthesupportingfurniture.•Notplacingthemonitorontallfurniture(forexample,cupboardsorbookcases)withoutanchoringboththefurnitureandthe

monitor to a suitable support.•Notstandingthemonitorsonclothorothermaterialsplacedbetweenthemonitorandsupportingfurniture.•Educatingchildrenaboutthedangersofclimbingonfurnituretoreachthemonitororitscontrols.

Especially for child safety-Don’tallowchildrentoclimbonorplaywiththemonitor.-Don’tplacethemonitoronfurniturethatcaneasilybeusedassteps,suchasachestofdrawers.-Rememberthatchildrencanbecomeexcitedwhilewatchingaprogram,especiallyona“largerthanlife”monitor.Care

should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.-Careshouldbetakentorouteallcordsandcablesconnectedtothemonitorsothattheycannotbepulledorgrabbedby

curious children.

7 E

-TheTFTcolorLCDpanelusedinthismonitorismadewiththeapplicationofhighprecisiontechnology.However,theremay be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from an acute angle there may be uneven colors or brightness. Please note that these are not malfunctions but common phenomenaofLCDsandwillnotaffecttheperformanceofthe monitor.

-Donotdisplayastillpictureforalongperiod,asthiscouldcause a residual image.

-Neverrubortapthemonitorwithhardobjects.-PleaseunderstandthatSHARPCORPORATIONbearsno

responsibility for errors made during use by the customer or a third party, nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognizedunderlaw.

-Thismonitoranditsaccessoriesmaybeupgradedwithoutadvance notice.

-Donotusethemonitorwherethereisalotofdust,wherehumidity is high, or where the monitor may come into contact withoilorsteam,asthiscouldleadtofire.

-Ensurethatthemonitordoesnotcomeintocontactwithwaterorotherfluids.Ensurethatnoobjectssuchaspaperclipsorpinsenterthemonitorasthiscouldleadtofireorelectric shock.

-Donotplacethemonitorontopofunstableobjectsorinunsafeplaces.Donotallowthemonitortoreceivestrongshocksortostronglyvibrate.Causingthemonitortofallortopple over may damage it.

-Donotusethemonitornearheatingequipmentorinplaceswhere there is likelihood of high temperature, as this may leadtogenerationofexcessiveheatandoutbreakoffire.

-Donotusethemonitorinplaceswhereitmaybeexposedtodirect sunlight.

-TheACoutletshallbeinstalledneartheequipmentandshallbe easily accessible.

-DonottouchthescreenwhilethePCisstartingup,sinceit will be detected as a failure of the infrared transmitter/receiverelementsandwillleadtoamalfunction.Whenthisoccurs,restartthePC.

-Donotoperatethescreenwithahardorpointedobjectsuchasafingernail,pen,orpencil.

-Twotouchpanelscannotbeusedwhentwodisplaysareconnected to the computer. Only the touch panel on the display that is set as the primary monitor will be operable.

-IfanotherUSBdeviceisconnectedtothecomputertowhichthetouchpanelisconnected,donotoperatetheUSBdeviceduring touch panel input. Input may not take place correctly.

-Iftwotouchpanelsareusedincloseproximitytoeachother,use handwriting mode. The touch pens will interfere with each other and will not operate correctly.

-Iftheinfraredtransmitter/receiverbecomesdirty,malfunctioning may result. Use a soft cloth to gently wipe dirt off the infrared transmitter/receiver.

-Ifdustaccumulatesinsidetheinfraredtransmitter/receiver,the product cannot transmit or receive infrared rays properly, resulting in a malfunction. To clean the dust accumulated inside,contactanauthorizedSHARPservicingdealerorservicecenter(extrachargerequired).

The Power Cord-Useonlythepowercordsuppliedwiththemonitor.-Donotdamagethepowercordnorplaceheavyobjectson

it, stretch it or over bend it. Also, do not add extension cords. Damagetothecordmayresultinfireorelectricshock.

-Donotusethepowercordwithapowertap. Addinganextensioncordmayleadtofireasaresultofoverheating.

-Donotremoveorinsertthepowerplugwithwethands.Doingsocouldresultinelectricshock.

-Unplugthepowercordifitisnotusedforalongtime.-Donotattempttorepairthepowercordifitisbroken

or malfunctioning. Refer the servicing to the service representative.

Manual Scope-Microsoft,Windows,WindowsVistaandInternetExplorerareregisteredtrademarksofMicrosoftCorporation.

-HDMI,theHDMILogoandHigh-DefinitionMultimediaInterfacearetrademarksorregisteredtrademarksofHDMILicensingLLC.

-Adobe,Acrobat,andReaderareeitherregisteredtrademarksor trademarks of Adobe Systems Incorporated in the United States and/or other countries.-Intel,Celeron,andIntelCore2DuoaretrademarksorregisteredtrademarksofIntelCorporationoritssubsidiariesin the U.S.A. and other countries.

-AMD,AMDSempron,AMDAthlon,andcombinationsthereofaretrademarksofAdvancedMicroDevices,Inc.-ThisproductcomeswithRICOHBitmapFontsproducedandsoldbyRICOHCOMPANY,LTD.

-Allotherbrandandproductnamesaretrademarksorregistered trademarks of their respective holders.-LanguageofOSDmenuusedinthismanualisEnglishby

way of example.-Illustrationsinthismanualmaynotexactlyrepresentthe

actual product or display.

LED Backlight● TheLEDbacklightinthisproducthasalimitedlifetime. *Ifthescreengetsdarkordoesnotturnon,itmaybe

necessarytoreplacetheLEDbacklight.ThisLEDbacklight is exclusive to this product and must be replaced byanauthorizedSHARP servicing dealer or service center.

*PleasecontactyourlocalSHARP servicing dealer or service center for assistance.

TIPS AND SAFETY INSTRUCTIONS

8E

MOUNTING PRECAUTIONS

• Thisproductisforuseindoors.• AmountingbracketcompliantwithVESAspecificationsis

required.• Sincethemonitorisheavy,consultyourdealerbefore

installing,removingormovingthemonitor.• Mountingthemonitoronthewallrequiresspecialexpertise

andtheworkmustbeperformedbyanauthorizedSHARPdealer.Youshouldneverattempttoperformanyofthisworkyourself.Ourcompanywillbearnoresponsibilityforaccidentsorinjuriescausedbyimpropermountingormishandling.

• Thismonitorcannotbeusedinverticalorientation.• Usethemonitorwiththesurfaceperpendiculartoalevel

surface.Ifnecessary,themonitormaybetiltedupto20degreesupward.

• Whenmovingthemonitor,besuretoholditwitheitherhandlesorthecornersonthebottomoftheunit.Donotplaceyourhandonthescreen.Thismaycauseproductdamage,failure,orinjury.

• Thismonitorshouldbeusedatanambienttemperaturebetween41°F(5°C)and95°F(35°C).Provideenoughspacearoundthemonitortopreventheatfromaccumulatinginside.

7-7/8 [20]Unit: inch [cm]

2 [5]

2[5]

2[5]

1-7/16 [3.5]

• Ifitisdifficulttoprovidesufficientspaceforanyreasonsuchastheinstallationofthemonitorinsideahousing,oriftheambienttemperaturemaybeoutsideoftherangeof41°F(5°C)to95°F(35°C),installafanortakeothermeasurestokeeptheambienttemperaturewithintherequiredrange.

• TemperatureconditionmaychangewhenusingthemonitortogetherwiththeoptionalequipmentsrecommendedbySHARP.Insuchcases,pleasecheckthetemperatureconditionspecifiedbytheoptionalequipments.

• Donotblockanyventilationopenings.Ifthetemperatureinsidethemonitorrises,thiscouldleadtoamalfunction.

• Donotplacethemonitoronadevicewhichgeneratesheat.• Donotusetheproductinlocationswheretheunitis

exposedtodirectsunlightorotherstronglight.Sincethisproductoperateswithinfraredrays,suchlightmaycauseamalfunction.

• FixtheUSBcablewiththecableclamp(supplied).(1) Coilthecableintotwoloopsapprox.1-9/16inches

(4cm)indiameteratapprox.5-7/8inches(15cm)fromtheminiUSBconnector.

(2) FixtheloopstothefixingpartabovetheUSBportwiththecableclamp.

(2)

(1)

9 E

Forinformationonthetouchpaneldriver,seetheTouchPanelDriverOperationManual.ForinformationonthePenSoftware,see the Pen Software Operation Manual.

Supplied ComponentsIf any component should be missing, please contact your dealer. LiquidCrystalDisplayMonitor:1 Remotecontrolunit:1 Cableclamp:3 Powercord:1 R-6battery(“AA”size):2 CD-ROM(UtilityDiskforWindows):1 SetupManual:1 Touchpen:1* SharpCorporationholdsauthorshiprightstotheUtilityDiskprogram.Donotreproduceitwithoutpermission.* Forenvironmentalprotection! Donotdisposeofbatteriesinhouseholdwaste.Followthedisposalinstructionsforyourarea.

Pen tip (for touch pen): 2 Touch pen battery (LR-03(“AAA”size)):1

USBcable:1 Eraser:1 Tray:1 Traymountingfitting

(cover / bracket): x 2

System RequirementsTo use the touch panel, the touch panel must be connected to a computer, and the touch panel driver and Pen Software must be installedonthecomputerfromthesuppliedCD-ROM.Systemrequirementsforeachsoftwareprogramareasfollows.

Computer PC/ATcompatiblecomputerwithaUSB1.1port(mustbeabletosupplya500mA(5.0V)current)andabletooutputaresolutionof1920x1080.(CD-ROMdriverequiredforsoftwareinstallation.)

OS WindowsXP(32-bitor64-bitversion),WindowsVista(32-bitor64-bitversion),Windows7(32-bitor64-bitversion)

CPU IntelCeleronorAMDSempron1.6GHzorfasterIntelCore2DuoorAMDAthlonIIX22.8GHzorfasterrecommended

Memory Atleast2GB(atleast1GBforWindowsXP)Freespaceonharddrive Atleast100MB(freespaceseparatelyrequiredfordatastorage)

Toconnectthetouchpanelandinstallthetouchpaneldriver,seetheTouchPanelDriverOperationManual.To install the Pen Software, see the Pen Software Operation Manual.

ContentsIMPORTANT INFORMATION ............................................3DEAR SHARP CUSTOMER ..............................................5SAFETY PRECAUTIONS ..................................................5TIPS AND SAFETY INSTRUCTIONS ...............................7MOUNTING PRECAUTIONS ............................................8Supplied Components .....................................................9System Requirements .....................................................9Part Names .....................................................................10Connecting Peripheral Equipment ...............................12

ConnectionwithaPCorAVequipment .....................12ConnectionwhenthePN-ZB01(optional) is attached ..................................................................13

Connecting the Power Cord .........................................14Binding Cables ...............................................................14Removing the Handles ..................................................14Preparing the Remote Control Unit ..............................15

Installing the batteries ................................................15Remote control operation range .................................15

Turning Power On/Off ....................................................16Turning on the main power.........................................16Turning power on/off ..................................................16Disablingpoweron/offoperations ..............................17

Touch Pen Preparations/Touch Action ........................18Inserting the battery ...................................................18Touch action and touch mode ....................................18

Touch action ...............................................................18Other functions ...........................................................20Cautionarypoints .......................................................20Eraser .........................................................................20

Basic Operation .............................................................21Menu Items .....................................................................23

Displayingthemenuscreen .......................................23Menu item details .......................................................24AdjustmentsforPCscreendisplay ............................30

Initialization (Reset)/Functional Restriction Setting (FUNCTION) ....................................................................31Controlling the Monitor with a PC (RS-232C) ..............32

PCconnection ............................................................32Communicationconditions .........................................32Communicationprocedure .........................................32SettingoftheGAMMAuserdata ................................35RS-232Ccommandtable ...........................................36

Controlling the Monitor with a PC (LAN) .....................43Settings to connect to a LAN ......................................43ControllingwithaPC ..................................................45

Troubleshooting .............................................................51Specifications ...............................................................53Mounting Precautions (For SHARP dealers and service engineers) ...............57

Traymountingscrews:M5x4/M4x2 Terminallabel:1

Used when installing the expansion board PN-ZB01(optional).

CoverSharplogo:1 PlacethisstickerontotheSHARPlogotocover the logo.

10E

nFront view

76 8

1 1

5

2 2

2

2

4 3

1. Touch pen ultrasonic sensor 2. Infrared transmitter/receiver 3. Power button (Seepage16.) 4. Tray 5. Touch panel power LED 6. Remote control sensor (Seepage15.) 7. Input switch (Seepage21.) 8. Power LED (Seepage16.)

Part Names

nRear view

1817

16

19

222120

2423

2

1

4

1514

5

6

789101112

3

25

13

When the PN-ZB01(optional) is attached

1. Optional attachment sectionThis section is used to connect optional hardware for function expansion. Offering this attachment location is not a guarantee that future compatible hardware attachments will be released.

2. Speakers 3. Handles (Seepage14.) 4. Vents 5. Expansion terminal cover

Additional input/output terminals are availablebyattachingthePN-ZB01expansion board (optional).

6. PC/AV HDMI input terminal (See page 12.)

7. PC D-sub input terminal (See page 12.)

8. Audio input terminal (Seepage12.) 9. Audio output terminals (Seepage12.) 10. RS-232C output terminal (See page

12.) 11. RS-232C input terminal (Seepage12.) 12. Optional terminal

This terminal is provided for possible future (optional) function expansion. Offering of this terminal is not a guarantee that future expanded functionality will be provided.

13. USB port 14. AC input terminal (Seepage14.) 15. Main power switch (Seepage16.)Caution

• ConsultyourSHARPdealerforattachment/detachmentofoptional parts.

• Donotopentheexpansionterminalcoverbyyourself. There are high voltage parts inside the cover which may cause an electric shock.

When the PN-ZB01 (optional) is attached 16. PC/AV DVI-D input terminal (Seepage13.) 17. PC/AV DVI-D output terminal (Seepage13.) 18. LAN terminal (Seepage13.) 19. External speaker terminals (Seepage13.) 20. Audio 1 input terminals (Seepage13.) 21. Audio 2 input terminals (Seepage13.) 22. PC RGB input terminals (Seepage13.) 23. AV component input terminals (Seepage13.) 24. AV video input terminal (Seepage13.) 25. AV S-video input terminal (Seepage13.)

11 E

Part Names

nRemote control unit1

2

3

4

5

6

9

8

7

1. Signal transmitter 2. POWER button(Seepage16.) 3. MUTE button(Seepage21.) 4. VOL +/- buttons(Seepage21.) BRIGHT +/- buttons(Seepage21.) Cursor control ( / / / ) buttons 5. DISPLAY button(Seepage21.) 6. MODE button(Seepage21.) 7. INPUT button(Seepage21.) 8. MENU button(Seepage21.) 9. SIZE button(Seepage21.)

12E

Connecting Peripheral Equipment

Caution

• Besuretoturnoffthemainpowerswitchanddisconnecttheplugfromthepoweroutletbeforeconnecting/disconnectingcables.Also,readthemanualoftheequipmenttobeconnected.

• Becarefulnottoconfusetheinputterminalwiththeoutputterminalwhenconnectingcables.Accidentallyreversingcablesconnectedtotheinputandoutputterminalsmaycausemalfunctionsandtheotherproblems.

TIPS

• Whenusingthetouchpanel,connecttheUSBcabletothecomputer.Fordetails,seetheTouchPanelDriverOperationManual.

• Imagesmaynotbedisplayedproperlydependingonthecomputer(videocard)tobeconnected.

• Ascreenwith1920x1080resolutionmaynotbedisplayedcorrectlyonPCRGB.Inthiscase,checkthesettingsofyourcomputer(videocard)toverifythatinputsignalsconformtospecificationsofthismonitor.(Seepage55.)

• IfthereisacheckboxtodisableEDIDindisplaycontrolpanel,checkitwhenusingPCRGB.

• UsetheautomaticscreenadjustmentwhenaPCscreenisdisplayedforthefirsttimeusingPCD-SUBorPCRGB,orwhenthesettingofthePCischanged.ThescreenisadjustedautomaticallywhenSELFADJUSTintheOPTIONmenuissettoON.

• Iftheaudiooutputfromtheplaybackdeviceisconnecteddirectlytospeakersorotherdevices,thevideoonthemonitormayappeardelayedfromtheaudioportion.Audioshouldbeplayedthroughthismonitorbyconnectingtheplaybackdevicetothemonitor’saudioinput,andconnectingthemonitor’saudiooutputtothespeakersorotherdevices.

• Theaudioinputterminalsusedineachinputmodearefactory-setasfollows.

Input mode Audio input terminal(Factory setting)

PCD-SUB,PCDVI-D,PCRGB AudioinputterminalAVDVI-D Audio1inputterminalAVCOMPONENT(BNC),AVS-VIDEO,AVVIDEO(BNC) Audio2inputterminal

AVCOMPONENT(D-SUB),AVVIDEO(D-SUB) Audioinputterminal

PCHDMI,AVHDMI PC/AVHDMIinputterminal

Connection with a PC or AV equipment 1. PC/AV HDMI input terminal• UseacommerciallyavailableHDMIcable(conformingto

theHDMIstandard).• SetHDMIofINPUTSELECTontheOPTIONmenu

accordingtothedevicetobeconnected.• SelecttheaudioinputterminaltobeusedinPCHDMI

orAVHDMIofAUDIOSELECTontheOPTIONmenu.WhenHDMIisselected,connectiontotheaudioinputterminalisunnecessary.

2. PC D-sub input terminal• SetD-SUBofINPUTSELECTontheOPTIONmenu

accordingtothedevicetobeconnected.• CommonterminalforAVCOMPONENTandAVVIDEO.• WhenthePN-ZB01(optional)isattached,selecttheaudio

inputterminaltobeusedinPCD-SUBofAUDIOSELECTontheOPTIONmenu.

• TousewithAVVIDEO(D-SUB),connectthegreenterminaltothedevice’svideooutput.

3. Audio input terminal• Useanaudiocablewithoutresistance.• WhenthePN-ZB01(optional)isattached,settheaudio

inputterminalusedforeachinputmodeinAUDIOSELECTontheOPTIONmenu.

4. Audio output terminals• Theoutputsoundvariesdependingontheinputmode.• Thevolumeoftheoutputsoundcanbefixedbysetting

AUDIOOUTPUT(RCA)ontheOPTIONmenu.• Itisnotpossibletocontrolthesoundoutputfromthe

audiooutputterminalswiththeAUDIOmenu.

5. RS-232C input terminal RS-232C output terminal

• YoucancontrolthemonitorfromaPCbyconnectingacommerciallyavailableRS-232straightcablebetweentheseterminalsandthePC.

6. USB port• Tousethetouchpanel,connectthetouchpaneltoyour

computerwiththeprovidedUSBcable.(TouchPanelDriverOperationManual.)

1315

7

14

8

12

109

1

23455

When the PN-ZB01 (optional) is attached

11

6

13 E

Connecting Peripheral Equipment

Connection when the PN-ZB01 (optional) is attachedThePN-ZB01expansionboard(optional)allowstheuseofadditional connection terminals.

7. PC/AV DVI-D input terminal• SetDVIofINPUTSELECTontheOPTIONmenu

according to the device to be connected.• SelecttheaudioinputterminaltobeusedinPCDVI-Dor

AVDVI-DofAUDIOSELECTontheOPTIONmenu.

8. PC RGB input terminals• SetBNCofINPUTSELECTontheOPTIONmenutoPC

RGBwhenusingthePCRGBinputterminals.• SelecttheaudioinputterminaltobeusedinPCRGBof

AUDIOSELECTontheOPTIONmenu.

9. AV component input terminals• SetBNCofINPUTSELECTontheOPTIONmenuto

AVCOMPONENTwhenusingtheAVcomponentinputterminals.

• SelecttheaudioinputterminaltobeusedinAVCOMPONENTofAUDIOSELECTontheOPTIONmenu.

• CannotbeusedwhenD-SUBinINPUTSELECTontheOPTIONmenuissettoAVCOMPONENT.

10. AV video input terminal• SelecttheaudioinputterminaltobeusedinAVVIDEOof

AUDIOSELECTontheOPTIONmenu.• CannotbeusedwhenD-SUBinINPUTSELECTonthe

OPTIONmenuissettoAVVIDEO.

11. AV S-video input terminal• SelecttheaudioinputterminaltobeusedinAVS-VIDEO

ofAUDIOSELECTontheOPTIONmenu.

12. Audio1 input terminals / Audio2 input terminals• Settheaudioinputterminaltobeusedineachinput

modeinAUDIOSELECTontheOPTIONmenu.

13. LAN terminal• YoucancontrolthemonitorfromaPConanetworkby

connecting a commercially available LAN cable between this terminal and a network.

14. External speaker terminals• Touseexternalspeakers,setSPEAKERSELECTonthe

SETUPmenutoEXTERNAL.• Besuretouseexternalspeakerswithanimpedanceof6Ω

orgreaterandaratedinputofatleast7W.

1 32Approx.3-15/16 inch(10 cm)

1.Attachaspeakercablecore(includedwiththePN-ZB01)tothe end of the speaker cable connected to the monitor.

2.Whilepushingthetab,insertthetipofthecable.3. Release the tab.

TIPS

• Besuretoconnectthe+and-terminalsandtheleftandright speakers properly.

• Avoidshortcircuitingthe+and-terminals.• WhenSPEAKERSELECTissettoEXTERNAL,the

internal speakers are disabled.

15. PC/AV DVI-D output terminal• ThevideoofthePC/AVDVI-Dinputcanbeoutputtoan

external device.• OutputtingHDCP-encryptedvideorequiresanexternal

devicewhichsupportsHDCP.• Thisterminalallowsthedaisychainconnectionofupto5

monitors.

TIPS

• Thelengthofthesignalcablesorsurroundingenvironmentmayaffecttheimagequality.

• ThescreenmaynotdisplayproperlywhenusingterminalsotherthanPCDVI-D/AVDVI-Dfortheinputmode.Inthiscase, turn off the power to all the monitors connected in a daisy chain and then turn the power on again.

• WhenconnectingmonitorsinadaisychainsetAUTOINPUTCHANGEtoOFF.

• Videooutputisdisabledinthefollowingcases: Whenthepoweristurnedoff Whenthemonitorisininputsignalwaitingmode

14E

Connecting the Power CordCaution

• Useonlythepowercordsuppliedwiththemonitor.

1.Turnoffthemainpowerswitch.2.Plugthepowercord(supplied)intotheACinputterminal.3.Plugthepowercord(supplied)intotheACpoweroutlet.

Binding CablesThe cables connected to the terminals on the rear of the monitor can be fastened with the cable clamp.

Insert the cable clamp into the cable clamp attachment on the rear of the monitor and fasten the cables.

AC input terminal

1Main power switch

Power cord (Supplied)

For power outlet

2

3

Removing the Handles

Cable clamp

Cable clamp attachment

Cable

The handles can be removed.

Handle

Handle screws

Caution

• Theremovablehandlesandhandlescrewsareforusewiththismonitor.Donotusethemforanyotherdevices.• Toattachhandles,besuretousethehandlesandhandlescrewswhichwereremovedfromthemonitor.• Besurethehandlesareattachedsecurely.

15 E

Preparing the Remote Control UnitInstalling the batteries1.Pressthecovergentlyandslideitinthedirectionofthe

arrow.

2. See the instructions in the compartment and put in the suppliedbatteries(R-6(“AA”size)x2)withtheirplus(+)andminus(-)sidesorientedcorrectly.

3.Closethecover.

TIPS

• Whenthebatteriesbecomeexhausted,replacethemwithnew (commercially available) batteries.

• Thesuppliedbatteries(R-6(“AA”size)x2)maybecomeexhaustedquicklydependingonhowtheyarestored.

• Ifyouwillnotbeusingtheremotecontrolforalongtime,remove the batteries.

• Usemanganeseoralkalinebatteriesonly.

Remote control operation rangeTheoperationrangeoftheremotecontrolunitisapprox.16.4feet(5m)atanangleofapprox10°fromthecentertothetop/bottom/right/left of the remote control sensor.

10° 10°

10°

10°

Remote control sensor

16.4 feet (5 m)

TIPS

• Donotexposetheremotecontrolunittoshockbydroppingor stepping on it. This could lead to a malfunction.

• Donotexposetheremotecontrolunittoliquids,anddonotplace it in an area with high humidity.

• Theremotecontrolunitmaynotworkproperlyiftheremotecontrol sensor is under direct sunlight or strong lighting.

• Objectsbetweentheremotecontrolunitandtheremotecontrol sensor may prevent proper operation.

• Replacethebatterieswhentheyrunlowasthismayshorten the remote control’s operation range.

• Ifafluorescentlightisilluminatedneartheremotecontrolunit, it may interfere with proper operation.

• Donotuseitwiththeremotecontrolofotherequipmentsuch as air conditioner, stereo components, etc.

16E

Caution

• TurnonthemonitorfirstbeforeturningonthePCorplayback device.

Turning on the main power

Main power switch

Caution

• Themainpowermustbeturnedon/offwiththemainpowerswitch.Donotconnect/disconnectthepowercordorturnthe breaker on/off while the main power switch is on.

• WhenswitchingthemainpowerswitchorthePOWERbuttonoffandbackon,alwayswaitforatleast5seconds.

• Foracompleteelectricaldisconnection,pulloutthemainplug.

Turning Power On/OffTurning power on/offPressthePOWERbuttontoturnthepowerON/OFF.

POWERbutton

Power LED

Touch panel power LED

• StatusofthepowerLED

Status Status of the monitorGreenlit Power onOrange lit Power off (Standby mode)Greenflashing Input signal waiting mode

• StatusofthetouchpanelpowerLED

Status Status of the touch panelGreenlit Operating normallyBlinkingorangeAlternately blinking green and orange

Initializing

Off Touch panel off (power not supplied, etc.)

Caution

• WhenswitchingthemainpowerswitchorthePOWERbuttonoffandbackon,alwayswaitforatleast5seconds.A short interval may result in a malfunction.

• WhenthetouchpanelpowerLEDblinksorangeoralternately blinks green and orange, the touch panel is beinginitialized.Donottouchthetouchpanelatthistime.Touching the touch panel may cause malfunctioning.

TIPS

• Whenthemainpowerswitchisoff,themonitorcannotbeturned on.

• IfthemonitorisintheinputsignalstandbymodeandyoupressthePOWERbuttonontheremotecontrolunit,themonitor enters standby mode.

• SettingtheSCHEDULEflashesthepowerLEDalternatelyin red and orange in standby mode.

• TodisablethelogoscreenfromdisplayingwhenturningthepowerON,setLOGOSCREENtoOFFontheSETUPmenu. (See page 26.)

17 E

Turning Power On/Off

nDate/time setting• Ifthetimehasyettobesetwhenthemonitorisfirstturned

on, the date/time setting screen appears. Set the date and time.

DATE/TIME SETTING

SET

CANCEL

/ /

OK···[MENU]

: :

01 01 11/ 12 AM00:/ 20

1. Press , , or to select the date and time, and press or to change the numerical values.

2. Press or toselectSETandthenpressMENU

.• Besuretosetthedateandtime.• Thedate/timesettingscreenwillcloseautomaticallyifnooperationisperformedforabout15seconds.ThedateandtimecanbesetusingDATE/TIMESETTINGfromthe OPTION menu when the date/time setting screen disappears.

TIPS

• Setthedatein“Month/Day/Year”order.• Setthetimeona12-hourbasis.• The clock is maintained by the internal battery.• If you already set the time but the date/time setting

screen appears when the power is turned on, the internal battery may be exhausted. Please contact your local SHARP servicing dealer or service center for assistance with battery replacement.

• Estimatedservicelifeoftheinternalbattery:About5years (depending on monitor operation)

• The initial battery was inserted at the factory when the monitor was shipped, so it may run out of power before its expected operation life.

Disabling power on/off operationsPower on/power off operations can be disabled in order to protect the monitor from an accidental power off. Set the ADJUSTMENTLOCKinFUNCTIONmenuto“ON2”.(Seepage31.)

18E

Touch Pen Preparations/Touch ActionInserting the battery1.Rotatethebatterycapandremoveit,andthenpulloutthe

cover.

Battery cap

2. Insertthesuppliedbattery(LR-03(“AAA”size))intheorientation shown, and attach the cover and battery cap.

TIPS

• Thesuppliedbattery(LR-03(“AAA”size))maybeexhausted in a short time, depending on how it was stored.

• Ifthetouchpenwillnotbeusedforanextendedtime,remove the battery from the touch pen.

• Forthebattery,useanalkalinebattery.

Touch action and touch modeTouch panel actions that can be used vary depending on the touch mode setting in the touch panel driver.InWindowsXP/WindowsVista,dualtouchmodecannotbeused.

Touch mode

Touch actionSingle touch mode Dual touch mode

Single-tap Yes Yes

Double-tap Yes Yes

Drag-and-drop Yes Yes

Flicks No Yes

Press-and-hold No Yes

Pan No Yes

Zoom No Yes

Press-and-tap No Yes

TIPS

• Settingsfortouchpaneloperationsuchasthetouchmodeand actions of the function buttons can be changed in the touchpaneldriver.Fordetails,seethemanualforthetouchpanel driver.

• InWindows7,ifthecheckmarkhasbeenremovedfrom“Enablemulti-touchgesturesandinking”in“Penandtouch”inControlPanel,selectthecheckbox.

Touch actionWhenthetouchpanelistouchedwiththepen,theinputmodechangestopenmode.Whentouchedwithyourfinger,theinput mode changes to handwriting mode. The input mode is set by default to change automatically (Standard mode).

TIPS

• FortheproceduresforusingthetouchpeninthePenSoftware, see the Pen Software Operation Manual.

nCommon finger and pen actionsSingle-tapSame action as left-clickingamouse.Touchwithyourfinger/pen.

19 E

Double-tap*1

Sameactionasdouble-clickingamouse.Quicklytouchtwicewithyourfinger/pen.

Whendouble-tappingwithyourfinger,besuretoliftyourfingersufficientlyoffthescreenafterthefirsttap.Ifthereisinsufficientdistancebetweenthescreenandyourfinger,double-tapwillnottakeplace.

Drag-and-dropSameactionasdrag-and-dropwithamouse.Touchthescreenwithyourfinger/penandmovewithoutlifting.When you havefinishedthemovement,liftyourfinger/pen.

Flicks*2

Flickyourfinger/peninthedirectionofthefunctionyouwantto use.

Flickyourfinger

Press-and-hold*2

Sameactionasright-clickingamouse.Pressbrieflywithyourfinger/pen,andthenliftyourfinger/penfrom the screen.

Pan*2

Use in a screen with a scrollbar.Withyourfinger/pentouchingthescreen,moveinthedirection you want to scroll. The screen scrolls in the direction of the movement.

*1 InWindowsXP/WindowsVista,thesettingscanbechangedinthe touch panel driver.

*2 Thesettingscanbechangedin"Penandtouch"ofControlPanel inWindows7.Fordetails,seeWindowsHelp.

nFinger actionsZoomUse in a screen that is capable of enlargement/reduction.Touchthescreenwithtwofingersandmoveyourfingerscloser together to reduce the view, or apart to enlarge the view.

Reduction

Enlargement

TIPS

• Moveyourfingerdiagonallyacrossthescreen.Ifyoumoveyourfingerhorizontallyorvertically,thescreenmaynotrespond correctly.

Touch Pen Preparations/Touch Action

20E

Press-and-tapSameactionasright-clickingamouse.Withonefingertouchingthescreen,taponce(singletap)withanotherfinger.

Withonefingertouching

Taponce(singletap)withanotherfinger

TIPS

• Thescreenmaynotrespondcorrectlyinthefollowingcases:TouchingistooquickThe distance between the two points is too shortThe two points intersect

• Operationwiththetouchpenisnotpossible.

nPen actions

Pen tip

Function Button 2

Function Button 1

Ultrasonic transmitter

Battery indicator

Function Button 1PressingFunctionButton1hasthesameactionasright-clicking a mouse.The battery indicator illuminates.

Function Button 2InthePenSoftware,pressingFunctionButton2hastheaction that is set in the Pen Software.The battery indicator illuminates.

TIPS

• UseFunctionButton1andFunctionButton2nearthefrontof the screen. If too far away, operation will not be possible.

• PressFunctionButton1andFunctionButton2slowlyandfirmly.Ifpressedtooquickly,theactionwillnotberecognized.

• Ifthepentipbecomeswornordamaged,replaceit.Pullout the old pen tip and insert a new pen tip.

Other functionsInWindows7,touchpointerandinputpanelfunctionscanbeused.Forinformationonthesefunctions,seeWindowsHelp.

Touch pointer :A translucent image of a mouse appears near the point touched. The left/right buttons of the image can be clicked to perform the same actions as left/right clicking a mouse.

Input panel :A software keyboard and an input panel with handwriting recognition appear on the screen.

InWindows7(excludingStarter),theinkfunctionofMicrosoftOfficecanbeused.Handwrittencommentscanbewritten,andhandwritingcanberecognized.Fordetails, see MicrosoftOfficeHelp.

Cautionary points• Donotusethetouchpenforanypurposeotherthantouch

panel operation.• Donotpresshardonthepentip.• Do not cover the ultrasonic transmitter of the touch pen with

yourhandorfinger.• Operation will not take place correctly if there is an obstacle

between the infrared transmitter/receiver and the touch pen oryourfinger.Operationwillnottakeplacecorrectlyifyourfingers or your sleeve is near the screen.

• Ifthetouchpenisheldtooflatagainstthescreen,thetouch position may not be correctly detected.

• Ifthetouchpendoesnotworkattheedgeofthescreen,move it slowly.

• Donotstorewiththepentipofthetouchpenorfunctionbutton pressed. The battery will be exhausted.

• Donotusenearadevicethatemitsultrasonicwaves.Thetouch pen uses ultrasonic waves and may not operate correctly.

• Iftwotouchpanelsareusedincloseproximitytoeachother, use handwriting mode. The touch pens will interfere with each other and will not operate correctly.

• Ifthereisdirtorforeignmatteronthetipofthetouchpen,removeit.Foreignmattermaydamagethescreen.

• Applicationssuchasascreensaverormediaplayermaycause the resolution to automatically change. If "Resolution ChangeNotice"isenabledinthetouchpaneldriver,aresolution change message will appear. In this case, disable"ResolutionChangeNotice",orchangethesettingin the application so that it does not change the resolution.

• Thepenmaybeoutofpositionintheloginscreen.Inthiscase, use the keyboard or mouse.

• IftheUSBcablebecomesdisconnected,thetouchpanelmay not operate correctly after the cable is reconnected. In this case, restart your computer.

EraserTheeraserisusedwiththePenSoftware.Fortheprocedurefor using the eraser, refer to the Pen Software Operation Manual.

Caution

• Whenusingtheeraser,gentlybringtheclothsideintocontact with the screen. Touching the screen with one of thenon-clothsideswilldamagethescreen.

• Ifthereisanydirtorforeignmatteronthesurfacethatcontactsthescreen,removeit.Foreignmattermaydamagethe screen.

Touch Pen Preparations/Touch Action

21 E

Basic Operation

1

2 3 4

5

6 7

8

1. INPUT (Input mode selection)The menu is displayed. Press or to select the input mode, and press to enter.* Youcanselecttheinputterminalbypressingtheinput

switch of the monitor.Input mode Video Audio

PCD-SUB PCD-subinputterminal*1 Audio input terminalPCHDMI PC/AVHDMIinputterminal*2

*3AVHDMI PC/AVHDMIinputterminal*2

AVCOMPONENT PCD-subinputterminal*1Audio input terminal

AVVIDEO PCD-subinputterminal*1

When the PN-ZB01 (optional) is attachedInput mode Video Audio

PCDVI-D PC/AVDVI-Dinputterminal*4

*3

PCHDMI PC/AVHDMIinputterminal*2

PCD-SUB PCD-subinputterminal*1

PCRGB PCRGBinputterminals*5

AVDVI-D PC/AVDVI-Dinputterminal*4

AVHDMI PC/AVHDMIinputterminal*2

AVCOMPONENTAVCOMPONENTinputterminals*5

PCD-subinputterminal*1

AVS-VIDEO AVS-videoinputterminal

AVVIDEOAVvideoinputterminalPCD-subinputterminal*1

*1 SelecttheterminaltobeusedinD-SUBofINPUTSELECT.(Seepage26.)

*2 SelecttheterminaltobeusedinHDMIofINPUTSELECT.(See page 26.)

*3 SelecttheterminalforAUDIOSELECTwhichisusedforaudio input. (See page 26.)

*4 SelecttheterminaltobeusedinDVIofINPUTSELECT.(See page 26.)

*5 SelecttheterminaltobeusedinBNCofINPUTSELECT.(See page 26.)

2. MUTETurns off the volume temporarily.PresstheMUTEbuttonagaintoturnthesoundbacktotheprevious level.

3. MENUDisplaysandturnsoffthemenuscreen.(seepage23.)

4. VOL +/- (Volume adjustment)Pressing or displaystheVOLUMEmenuwhenthemenu screen is not displayed.

V O L U M E 15

Press or toadjustthevolumeofthesound.* Ifyoudonotpressanybuttonsforabout4seconds,theVOLUMEmenuautomaticallydisappears.

5. BRIGHT +/- (Backlight adjustment)Pressing or displaystheBRIGHTmenuwhenthemenu screen is not displayed.

B R I G H T 15

Press or toadjustthebrightness.* Ifyoudonotpressanybuttonsforabout4seconds,theBRIGHTmenuautomaticallydisappears.

6. SIZE (Screen size selection)The menu is displayed.Press or toselectthescreensize.(Seepage22.)

7. DISPLAYDisplaysmonitorinformation.Whenyoupressthisbuttonagain, the display disappears.WhenthePN-ZB01(optional)isattached,thedisplaychangesfromINFORMATION1→INFORMATION2→cleardisplay,and so on every time you press this button.• Thedisplaydisappearsautomaticallyafterabout15

seconds.• LAN is displayed during LAN communication.• If LAN is displayed in red, there is a duplicate IP address.

8. MODE (Color mode selection)Eachtimeyoupressthisbutton,thecolormodechangesinthe following order:

STD(Standard)→VIVID→sRGB→STD...

• sRGBappliestoPCinputonly. sRGBisinternationalstandardofcolorrepresentationspecifiedbyIEC(InternationalElectrotechnicalCommission).Colorconversionismadeintakingaccountofliquidcrystal’scharacteristicsandrepresentscolortoneclose to its original image.

22E

Basic Operation

nSwitching the screen sizeEvenwhenthescreensizeischanged,thedisplaymayremainthesamedependingontheinputsignal.

WIDE PCinput Displaysimagesoitfillstheentirescreen.

AVinput Animagewitha4:3aspectratioisstretchedtofilltheentirescreen.

ZOOM 1 PCinput Animagewitha4:3aspectratioisenlargedtofilltheentirescreenwithout changing the aspect ratio. The edges of the image may be cut off.

AVinput

ZOOM 2 PCinput UsethissizeifZOOM1cutsoffthesubtitles.

AVinput

NORMAL PCinput Displaysimagesoitfillsthescreenwithoutchangingtheaspectratio of the input signals.

AVinput Displaystheentireimageoftheaspectratioof4:3withoutchanging the aspect ratio.

Dot by Dot PCinput DisplaysthedotsofthesignalsinputfromtheconnectedPCasthe corresponding dots on the screen.

AVinput Displaysthedotsoftheinputsignalsasthecorrespondingdotsonthe screen.

TIPS

• Usingthismonitor’sscreen-sizeswitchingordual-screendisplayfunctionstocompressorexpandthescreenforcommercialorpublicviewinginestablishmentslikecafesorhotelsmayinfringeontherightsofthecreators,asprotectedbyCopyrightLaw, so please be careful.

• Whendual-screendisplayisselected,thescreensizecannotbechanged.• Theappearanceoftheoriginalvideomaychangeifyouselectascreensizewithadifferentaspectratiothantheoriginalimage(e.g.TVbroadcastorvideoinputfromexternalequipment).

• Whenanordinarynon-wideimage(4:3)isviewedwiththewholescreenusingthescreen-sizeswitchingfunctionofthismonitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen sizeto“NORMAL”.

• Whenplayingcommercialsoftware,partsoftheimage(likesubtitles)maybecropped.Inthiscaseselecttheoptimalscreensizeusingthescreen-sizeswitchingfunctionofthismonitor.Withsomesoftware,theremaybenoiseordistortionattheedges of the screen. This is due to the characteristics of the software, and is not a malfunction.

• Dependingontheoriginalimagesize,blackbandsmayremainattheedgesofthescreen.

23 E

Menu ItemsDisplaying the menu screenVideo and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 24 to 27 for details of each menu items.

Caution

• Donotturnthemainpowerswitchoffwhilethemenuitemsarebeingdisplayed.Doingsomayinitializethesettings.

nExample of operation(Adjusting CONTRAST in the PICTURE menu)1. Press

MENU to display the menu screen.

1 9 2 0 x 1 0 8 0 V: 60 Hz H: 67.5 kHz

AUTOCLOCKPHASEH-POSV-POSH-SIZEV-SIZEH-RESOLUTIONV-RESOLUTIONRESET

SCREEN

PICTURE

AUDIO

SETUP

OPTION

PIP/PbyP

60025

610375050

19201080

SCREEN 1/1

END···[MENU]

PC D-SUB

2. Press or to select PICTURE, and press .

3. Press or to select CONTRAST.

AUTOANALOG GAINANALOG OFFSETBRIGHTCONTRASTBLACK LEVELTINTCOLORSSHARPNESSRGB INPUT RANGE

6486313030303012

1/2

FULL

PC D-SUBPICTURESCREEN

PICTURE

AUDIO

SETUP

OPTION

PIP/PbyP

OK···[MENU]MOVE OSD···[DISPLAY]1 9 2 0 x 1 0 8 0 V: 60 Hz H: 67.5 kHz

4. Press or to adjust the setting.

▲

▲

▲

AUTOANALOG GAINANALOG OFFSETBRIGHTCONTRASTBLACK LEVELTINTCOLORSSHARPNESSRGB INPUT RANGE

6486314030303012

1/2

FULL

PC D-SUBPICTURESCREEN

PICTURE

AUDIO

SETUP

OPTION

PIP/PbyP

OK···[MENU]MOVE OSD···[DISPLAY]1 9 2 0 x 1 0 8 0 V: 60 Hz H: 67.5 kHz

For items that have , press , make settings and then press

MENU.

5. Press MENU

twice to close the menu screen.

TIPS

• Themenuwilldifferdependingontheinputmode.• Themenuscreenwillcloseautomaticallyifnooperationisperformedforabout15seconds.(DATE/TIMESETTING,SCHEDULEandLANSETUPscreenswillcloseinabout4minutes.)

nMenu screen display

▲

▲

▲

AUTOANALOG GAINANALOG OFFSETBRIGHTCONTRASTBLACK LEVELTINTCOLORSSHARPNESSRGB INPUT RANGE

6486313030303012

1/2

FULL

PC D-SUBSCREEN

PICTURE

AUDIO

SETUP

OPTION

PIP/PbyP

PICTURE

OK···[MENU]MOVE OSD···[DISPLAY]1 9 2 0 x 1 0 8 0 V: 60 Hz H: 67.5 kHz

1 23

4

1 Name of the menu2 Input mode3 An item being selected (highlighted)4 Screen resolution of input signal, and other data.

TIPS

• Itemsthatcannotbeselectedappearingray. (e.g. Function not supported by the current input signal)

nMenu ItemsThe displayed menu items vary depending on whether or not the PN-ZB01 (optional) is attached.The following menus will be displayed only when the PN-ZB01 (optional) is attached.

Menu ItemSETUP HOTPLUGCONTROL DVI

RS-232C/LANSELECTLANSETUPAUTOASSIGNFIXEDIPADDR.SPEAKERSELECT

OPTION INPUTSELECT DVIBNC

AUDIOSELECT PCDVI-DPCD-SUBPCRGBAVDVI-DAVCOMPONENT(BNC)AVCOMPONENT(D-SUB)AVS-VIDEOAVVIDEO(BNC)AVVIDEO(D-SUB)

PIP/PbyP PIP SOURCE

24E

Menu item detailsThe menu will differ depending on the input mode.

nSCREENYou can move the menu screen display position each time DISPLAY is pressed.

AUTO (PC D-SUB/PC RGB)TheCLOCK,PHASE,H-POS,andV-POSareautomaticallyadjusted.Pressing performsadjustment.UsethisautomaticadjustmentwhenyouusethePCD-subinputterminalorPCRGBinputterminalstodisplayaPCscreenforthefirsttimeorwhenyouchangethesettingofthePC.(Seepage30.)CLOCK (PC D-SUB/PC RGB)Adjustsfrequencyfor sampling clock for applicable video.Adjustwhenthereisflickeringintheformofverticalstripes.Whenusingtheadjustmentpattern(seepage30),makeadjustmentssothatno vertical stripe noise appears in it.PHASE (PC D-SUB/PC RGB)Adjustssamplingclockphaseforapplicablevideo.Useful when small characters appear with low contrast and/orthereareflickersatcorners.Whenusingtheadjustmentpattern(seepage30),makeadjustmentssothatnohorizontalstripenoiseappearsinit.* AdjustmentstoPHASEshouldbemadeonlyafterCLOCK

has been correctly set.H-POSAdjustthehorizontalpositionoftheimage.V-POSAdjusttheverticalpositionoftheimage.H-SIZEAdjustthehorizontalsizeoftheimage.V-SIZEAdjusttheverticalsizeoftheimage.H-RESOLUTION (PC D-SUB/PC RGB)Sets properhorizontalresolutionwhentheresolutionofinputsignalsisnotrecognizedproperly.(Adjustmentmaybeimpossible with some signals.)V-RESOLUTION (PC D-SUB/PC RGB)Sets proper vertical resolution when the resolution of input signalsisnotrecognizedproperly.(Adjustmentmaybeimpossible with some signals.)RESETResetsthevaluesoftheSCREENmenuitemstothefactorypreset values.Select “ON” and then press

MENU.

nPICTUREYou can move the menu screen display position each time DISPLAY is pressed.

AUTO (PC D-SUB/PC RGB)The ANALOGGAINandANALOGOFFSETareautomaticallyadjusted.Pressing performsadjustment.ANALOG GAIN (PC D-SUB/PC RGB)Adjuststhebrightportionsofthevideoinputsignal.ANALOG OFFSET (PC D-SUB/PC RGB)Adjuststhedarkportionsofthevideoinputsignal.BRIGHTAdjuststhebacklightbrightness.(InPIPmode,themainsidesettingisreflectedintheimage.)CONTRASTAdjuststhedifferencebetweenthebrightanddarkportionsof the image.BLACK LEVELAdjuststheentirebrightnessofthevideosignals.TINTAdjuststhehue.Selecting+changesthecolortowardsgreen,andselecting-changesittowardsmagenta.COLORSAdjuststhecolorintensity.SHARPNESSAdjuststhesharpnessoftheimage.RGB INPUT RANGE (PC DVI-D/PC HDMI/PC D-SUB/PCRGB/AV DVI-D/AV HDMI)SetstheRGBinputsignalrange.WhenusingHDMIsettoAUTO,theRGBinputsignalisdetectedautomatically.UseAUTO normally.IftheRGBinputsignalrangecannotbesetappropriatelyevenwhenusingAUTO,setaccordingtotheimage.Whenthe setting is different, images will be displayed with washed out blacks and compressed gradients.ADVANCED (AV input)Youcanadjustmorespecifically.(Seepage30.)COLOR MODEChanges the color mode on the screen. The color mode on the screen can also be changed using a remote control unit. (Seepage21.)* sRGBisPCinputonly.Seepage21fordetails.(InPIPmode,themainsidesettingisreflectedintheimage.)WHITE BALANCETHRU .............. Displaystheinputsignallevelasis.(forPC

DVI-D/PCHDMIonly)PRESET ......... SelectsthecolortemperatureusingPRESET.USER .............. UsedforadjustingR-/G-/B-CONTRASTand

R-/G-/B-OFFSETrespectively.(InPIPmode,themainsidesettingisreflectedintheimage.)PRESETSelectsthecolortemperaturewhentheWHITEBALANCEissettoPRESET.The setting values are shown for reference. The color temperature of the screen varies over time.This function is not intended to keep the color temperature constant.

Menu Items

25 E

USERAdjustseachitemwhentheWHITEBALANCEissettoUSER.R-CONTRAST ....Adjustsbright-tonedredcomponent.G-CONTRAST ....Adjustsbright-tonedgreencomponent.B-CONTRAST ....Adjustsbright-tonedbluecomponent.R-OFFSET ..........Adjustsdark-tonedredcomponent.G-OFFSET .........Adjustsdark-tonedgreencomponent.B-OFFSET ..........Adjustsdark-tonedbluecomponent.COPY TO USERCopiesthevalueofwhitesetforPRESETtotheUSERsetting.Select “ON” and then press MENU .(In the case other than white, color tone may differ from the PRESET.)GAMMASelectsthegamma.USERsetsthegammatothesentvalue(seepage35).(InPIPmode,themainsidesettingisreflectedintheimage.)DISPLAY COLOR PATTERNDisplaysacolorpattern.Canbedisplayedwhilethemenuscreen is displayed, so you can refer to the pattern whileadjustingtheimage.OFF ..............No pattern display.WHITE ..........Whitesinglecolorpatterndisplay.RED ..............Red single color pattern display.GREEN .........Greensinglecolorpatterndisplay.BLUE ............Bluesinglecolorpatterndisplay.USER............Red/green/blue mixed color pattern display.

WhenUSERisselected,seteachcolor’slevel.

RESETResetsthevaluesofthePICTUREmenuitemstothefactorypreset values.Select “ON” and then press

MENU.

nAUDIOTREBLEAdjuststhevolumeoftreble-levelsound.BASSAdjuststhevolumeofbass-levelsound.BALANCEAdjuststhebalanceoftheaudiosoundbetweenrightandleft.RESETResetsthevaluesoftheAUDIOmenuitemstothefactorypresetvalues.Select “ON” and then press MENU .

nSETUPOSD H-POSITIONAdjuststhehorizontaldisplaypositionofmenuscreen.OSD V-POSITIONAdjuststheverticaldisplaypositionofmenuscreen.SCREEN MOTIONResidual images are reduced by moving the screen.PATTERN1 ......... The whole screen moves vertically and

horizontally.PATTERN2 ......... A black screen spreads from the bottom of

the screen and then shrinks to the bottom of the screen.

PATTERN3 ......... A black bar moves from the left end to the right end of the screen.

PATTERN4 ......... Blackscreensappearfromboththetop and bottom of the screen, and the displayed image is compressed into the centralfield.

PATTERN1 PATTERN2

PATTERN4PATTERN3

MOTION TIME 1Specifyatimeperiod(operatinginterval)untilSCREENMOTION starts.MOTION TIME 2SpecifyatimeperiodduringwhichSCREENMOTIONoperates (time period during which the screen will move).MONAURAL AUDIOOutputs audio signals as monaural.LANGUAGESets the display language for the menu screen.POWER ON DELAYYou can delay the screen display after the monitor is turned on.Theperiodcanbesetupto60secondsinunitsofonesecond.Whenthisfunctionisactivated,thepowerLEDflashes(atapprox.1secondinterval)inorange.Thisfunctionisdisabledwhen0isspecified.STANDBY MODEWhenSTANDARDisselected,startuptimefromstandbymode is reduced. Note, however that, more power will be consumed in standby mode.WhenLOWPOWERisselected,currentconsumptionis reduced while the monitor is in standby mode. Note, however, that the startup time from standby mode becomes longer. IfsettoLOWPOWER,certainRS-232Ccommandscannotbe used in standby mode, and control via LAN will be disabled.OFF IF NO OPERATIONDetermineswhetherornottosetthemonitortogointostandby mode when there is no operation from the remote controlunit,RS-232Ccommands,orLANforover4hours.

Menu Items

26E

Menu Items

nOPTIONDATE/TIME SETTING

Set the date and time. Press or to select the date and time, and press or to change the numerical values.Setthedatein“Month/Day/Year”order.Setthetimeona12-hourbasis.(Factorydefault)DATE/TIME FORMATSets the date/time display format.DATE ..................MM/DD/YYYY

DD/MM/YYYYYYYY/MM/DD(YYYY:Year,MM:Month,DD:Day)

TIME ...................Select12-or24-hourtime.SCHEDULE (See page 29.)You can turn the power on/off and change the screen brightnessataspecifiedtime.INPUT SELECTSelecttheinputmodetobeusedinPCD-Subinputterminal,PC/AVDVI-Dinputterminal,PC/AVHDMIinputterminalandPCRGB/AVcomponentinputterminals.ForD-SUB,selectSETafterselectingtheinputmode,andthen press MENU .D-SUBandBNCcannotbesettoAVCOMPONENTatthesame time.IfD-SUBissettoAVVIDEO,theAVVIDEOinputterminalcannotbeusedforBNC.AUDIO SELECTSelects the terminal used to input audio signals in each input mode.INPUT SIGNAL (PC D-SUB/PC RGB)IfacomputerconnectedtothePCD-sub/PCRGBinputterminal outputs any of the following resolutions, make a selection from the following options.480LINES .......... AUTO,640x480or848x480768LINES ..........AUTO,1024x768,1280x768,or1360x7681050LINES ........1400x1050or1680x1050ZOOM2SPECIALSETTING(See page 28.)SCAN MODE (AV input)SetsthescanmodeusedforAVmodeinput.MODE1 ............... Over-scandisplayMODE2 ...............Under-scandisplayMODE3 ............... Under-scandisplaywhentheinputsignal

is1080i/p.Otherwise,over-scandisplay*EvenwhenMODE1isselected,under-scandisplayisusedwhentheinputsignalis1080i/pandthescreensizeisDotbyDot.

POWER MANAGEMENTPOWERMANAGEMENTdetermineswhetherornottoswitch modes from no signal to the input signal standby mode.COLOR SYSTEM (AV S-VIDEO/AV VIDEO)SelectthecolorsystemoftheAVequipmentwhichisconnectedtoAVS-videoandAVvideoinputterminal.(AUTO/PAL/PAL-60/SECAM/NTSC3.58/NTSC4.43) WhenAUTOisselected,thecolorsystemisautomaticallyset according to the input signal.

HOT PLUG CONTROLSetswhethertousehotplugcontrolforthePC/AVHDMIandPC/AVDVI-Dinputterminals.RS-232C/LAN SELECTSelects the method with which to control the monitor from the computer.ID No. SETAssignsIDnumberstomonitorsconnectedinadaisychain(seepage33),usingtheRS-232cables.Thenumbers1to255areavailableforIDnumbers.If“0”isset,thesystemregardsthisasthestatewherenoIDnumber is set.AUTO ASSIGN ID No.IDNo.tobeusedwillbeautomaticallyassignedwhenmultiplemonitorsareconnectedwithRS-232C.Select ON, then press MENU . Performoperationsusingthefirstmonitorinthedaisychain.BAUD RATESelectsthecommunicationspeedusedforRS-232Ccommunication.LAN SETUPConfiguresthesettingstocontrolthemonitorfromthecomputer via LAN. (See page 43.)AUTO ASSIGN FIXED IP ADDR.CanbeenabledwhenRS-232C/LANSELECTisLANandtheDHCPCLIENTisOFF.SetDHCPCLIENTtoOFFforthemonitorconnectedtotheRS-232Coutputterminalandthedaisychainofconnectedmonitorsthatfollows.FixedIPaddressesareautomaticallyallocated.If the IP address is a duplicate with a network device other than a monitor, individually change the IP address.SPEAKER SELECTSelects the speaker to be used.HDMI AUTO VIEWWhenONisselected,thescreensizeisadjustedautomaticallyaccordingtothescreensizecontrolsignalincludedinthevideosignalinputfromtheAVHDMIinputterminal.COPY SETTING VALUEWhenthemonitorhasbeenconnectedtomultiplemonitorsbyRS-232C,thesettingsinthemonitorcanbecopiedtothemonitorconnectedtotheRS-232Coutputterminalandtothe daisy chain of connected monitors that follows.SelectsthesettingstocopywithCOPYSETTINGVALUETARGET.“PICTURE”ONLY .....CopiesthePICTUREmenusettings.*ALL ...........................Copiesallthesettings.*SelecttheIDNo.ofthemonitorthatyouwouldlikecopytowithCOPYTOIDNo.,thenselectCOPYandpressMENU .If you select ALL, settings will be copied to all monitors.WhenyouwouldliketoconfirmtheIDNo.thatissettothemonitor,selectIDNo.DISPLAYandpress .TheIDNo.will be displayed on the screen.*CertainsettingdetailssuchasANALOGGAIN,ANALOGOFFSET,andDISPLAYCOLORPATTERNcannotbecopied.

LOGO SCREENSets whether or not to display the logo screen.

27 E

Menu Items

AUDIO OUTPUT (RCA)Sets the volume of sound output from the audio output terminals.WhensettoVARIABLE2,soundwillnotbeoutputfromthebuilt-inspeakerortheexternalspeakerterminal.VARIABLE1 ........ YoucanadjustthevolumeusingVOLUME.VARIABLE2 ........ YoucanadjustthevolumeusingVOLUME.FIXED .................Fixesthesounds.AUDIO LEVEL (STEREO MINI)Selects the maximum audio input level of the audio input terminal.SELF ADJUSTOn a PCD-SUB/PCRGB screen, specify whether to performscreenadjustmentautomaticallyornot.WhenONisselected,thescreenisautomaticallyadjustedwhenitsresolutionis800x600orhigherandthetimingofinputsignalschanges.“ADJUSTING”appearsonthescreenduringtheadjustment.Forimageswithblackedges,etc.,dependingonthesignal,adjustmentmaynotbepossible.InthiscaseselectOFF.(Performmanualadjustmentofthescreen.)AUTO INPUT CHANGESpecifywhethertochangeinputsautomatically.WhenONisselected and no signal is present in the selected input mode, AUTOINPUTCHANGEautomaticallychangestheselectedmode to another mode where a video signal is present.Whenvideosignalsexistinmultipleinputmodes,theswitching priority is as follows:PCD-SUB,PCHDMI,AVHDMI,AVCOMPONENTandAVVIDEO

WhenthePN-ZB01(optional)isattached:PCDVI-D,PCHDMI,PCD-SUB,PCRGB,AVDVI-D,AVHDMI,AVCOMPONENT,AVS-VIDEOandAVVIDEO(Inputmodeswitchingmaytake15secondsormore,dependingontheconnectedequipment.Inputsignalsmay not be detected properly and a priority may change, dependingontheconnectedequipmentorvideosignals.)TOUCH PANEL MODE (PC input)Whentheresolutionis1920x1080,settingthistoONimproves touch panel tracking.Whentwoscreensaredisplayed,orwhenV-POSorV-SIZEisadjustedontheSCREENmenu,thescreenmaybecomedistorted.Inthisvent,settoOFF.

nPIP/PbyPPIP MODESSets the display method.OFF .........Displaysonescreen.PIP ...........Displaysasubscreeninsideamainscreen.PbyP ........Displaysamainscreenandasubscreeninaline.PbyP2 ......Displaysamainscreenwhichmeasures1280pixels

in the longest direction and a sub screen in a line.PIP SIZESetsthesizeofthesubscreeninPIPmode.PIP H-POSAdjuststhehorizontalpositionofthesubscreeninPIPmode.PIP V-POSAdjuststheverticalpositionofthesubscreeninPIPmode.PIP BLENDIn PIP mode, use this menu item to display the sub screen transparently.PIP SOURCESelects the input signal of the sub screen in PIP, PbyP, or PbyP2 mode.SOUND CHANGESets the sound which is output in PIP, PbyP, or PbyP2 mode.If the main screen is displayed as a full screen by the AUTO OFFfunction,thesoundforthemainscreenisoutputevenwhenthesoundforthesubscreenisspecified.MAIN POSSets the position of the main screen in PbyP or PbyP2 mode.PbyP2 POSSets the position of the sub screen in PbyP2 mode. AUTO OFFSets the display method when no signals for the sub screen are input in PIP, PbyP, or PbyP2 mode.MANUAL ....... Displaysamainscreenandablacksubscreen.AUTO ............Displaysthemainscreenasafullscreen.

TIPS

• WhenWHITEBALANCEissettoTHRU,BLACKLEVEL,CONTRAST,TINT,COLORS,RGBINPUTRANGE,GAMMAandCOPYTOUSERcannotbeset.

• IfCOLORMODEissettosRGB,thefollowingitemscannotbe set. WHITEBALANCE,PRESET,USER,COPYTOUSER,andGAMMA

• WhentheCOLORMODEissettoVIVID,GAMMAcannotbeadjusted.

• STANDBYMODEcannotbesettoLOWPOWERwhenSCHEDULEiseffectiveorwhenOFFisselectedforLEDinFUNCTION.

• Whendisplayingthecolorpattern,itispossibletoadjustcertainitemsofthePICTUREmenu. Non-adjustableitemscannotbeselected. AudioinputfromtheHDMIinputterminalisalsonotoutput.

28E

Menu Items

nDual screen displayYoucandisplaythescreensofthePCinputsignalandAVinput signal simultaneously.Setthisfunctionwith“PIPMODES”inthePIP/PbyPmenu.

PIPMain screen

Sub screen

A sub screen is displayed inside a main screen.

PbyP

Main screen

Sub screen

A main screen and a sub screen are displayed in a line.

PbyP2

Main screen Sub screen

Displaysamainscreenwhichmeasures1280pixels in the longest direction and a sub screen in a line.

* Thecurrentlyselectedinputsignalisdisplayedonthemainscreen.

* Youcannotsimultaneouslydisplaythescreensofsignalsofthesametype,suchastwotypesofPCinputsignalsortwotypesofAVinputsignals.

* ThedualscreendisplaycannotbeusedwiththecombinationofPCDVI-DandAVHDMIorofAVDVI-DandPCHDMI.

TIPS

• Youmightinfringeonacopyrightoftheauthorwhichisprotected by copyright law when you display the images of thecomputerscreenandtelevision/VCRsimultaneouslyforprofit-makingortoshowtheimagetothepublic.

• Thescreensizefordual-screendisplayisthesameasthescreensizeforsingle-screendisplay.TheDotbyDotscreenisdisplayedinNORMALsizeexceptwhenitissetas the PIP main screen.

• Whendual-screendisplayisselected,theSCREENMOTION function is disabled.

• Whendual-screendisplayisselected,theAUTOINPUTCHANGEfunctionisdisabled.

• Whendual-screendisplayisselected,theINPUTSELECToptions cannot be set.

• Whenaninterlacedsignal(1080i,480i,video,S-Video)isinputtothesubscreen,horizontallinesmayflicker.Ifthishappens, display the image on the main screen.

nZOOM2 SPECIAL SETTINGIf you connect a laptop computer with any of the following screen resolutions and black bands appear around the screen,setZOOM2SPECIALSETTINGofINPUTSIGNALontheOPTIONmenutoONandthenselectZOOM2intheSIZEsetting.This displays the area inside the black band.

Laptop computer resolution

Correspondingsignal*1

1280x800 1280x1024,1280x960,1400x1050*2

1280x600 1280x720

1024x600 1024x768

*1:Thissettingiseffectiveonlywhenthescreenresolution,including the black band, is one of the resolutions listed above.

*2:Usetheautomaticscreenadjustment.

29 E

nSCHEDULEYou can set the time to switch the monitor on and off.Setthisfunctionwith“SCHEDULE”intheOPTIONmenu.(Seepage 26.)

- :– – – – – – – – – – – –– – – – –

SCHEDULE

No. POWER DAY OF THE WEEK TIME INPUT BRIGHT

– –/– –/– – – – – – – – –:– –:– – – –PC D-SUB

(1)–

- :– – – – – – – – – – – –– – – – ––- :– – – – – – – – – – – –– – – – ––- :– – – – – – – – – – – –– – – – ––- :– – – – – – – – – – – –– – – – ––- :– – – – – – – – – – – –– – – – ––- :– – – – – – – – – – – –– – – – ––- :– – – – – – – – – – – –– – – – ––

(5)(2) (3) (4) (6)

OK···[MENU]1 9 2 0 x 1 0 8 0 V: 60 Hz H: 67.5 kHz

1. Press or to select the SCHEDULE number, and press .

2. Set the SCHEDULE. (See the description below.)Press or to select items, and press or to change the setting.

3. Press MENU .SCHEDULEbecomeseffective.

(1)●:SCHEDULEeffective-:SCHEDULEnoteffective(2) POWERON : Switchesthemonitoronatthespecifiedtime.OFF: Switchesthemonitoroffatthespecifiedtimeandputs

the monitor in standby mode.(3) DAY OF THE WEEKSpecifiesthedayoftheweektoexecutetheSCHEDULE.0:ONLYONCEExecutestheSCHEDULEonceonthespecifiedday.SpecifythedayoftheweektoexecutetheSCHEDULE.

1:EVERYWEEKExecutestheSCHEDULEonthespecifieddayoftheweekevery week. Specify the day of the week to execute the SCHEDULE. Periodicsettingsuchas“MondaythroughFriday”isalsopossible.

2:EVERYDAYExecutestheSCHEDULEeverydayregardlessofthedayof the week.

(4) TIMESpecifiesthetimetoexecutetheSCHEDULE.Setthetimeona12-hourbasis.(Factorydefault)Canbeenteredas24-hourtimeusingtheTIMEsettinginDATE/TIMEFORMAT.(5) INPUTSpecifiestheinputmodeatpower-on.Whennotspecifying,thescreenatthepreviouspower-offappears.InputmodesdisplayedonDVI,HDMI,BNCandD-SUBdependonINPUTSELECTsettings.(6) BRIGHTSets the brightness when changing the screen brightness at aspecifiedtime.

Menu Items

Caution

• DonotswitchoffthemainpoweraftersettingtheSCHEDULE.

• Specifythecorrectdateandtime.(Seepage26.) SCHEDULEdoesnotfunctionunlessthedateandtimearespecified.

• Checkregularlythatthesetdateandtimearecorrect.• WhenSTANDBYMODEisLOWPOWER,SCHEDULE

cannot be set.• Whenatemperatureabnormalityoccursandthebacklight

brightness is reduced, the brightness is not changed even ifaschedulesettoBRIGHTisexecuted.

TIPS

• Upto8SCHEDULEitemscanberegistered.• SettingtheSCHEDULEflashesthepowerLEDalternately

in red and orange in standby mode.• ASCHEDULEthathasalargenumberhasprecedence

over that of a small number when schedules overlap.• IfD-SUBofINPUTSELECTontheOPTIONmenuissettoAVVIDEO,theinputmodewillswitchtoAVVIDEO(D-SUB)regardlessifsettoD-SUBorVIDEO.

30E

nADVANCED items (AV input) (See page 24 for additional Menu item details.)FLESH TONEAdjustthehuecontrol.3D-NRReduce the noise of playback images on video.Settingahigherlevelreducesmorenoise.However,itmaycause blurring on an image.MPEG-NRReduce block noise caused by digital compression.3D-Y/C (AV VIDEO)Specifywhethertoperform3-dimensionY/Cseparation.Ifdotinterferenceorcross-colorisoccurringinfast-motionscenes,selecting“OFF”mayimprovetheimagequality.C.M.S.-HUEAdjustscolortonewith6colorsofR(red),Y(yellow),G(green),C(cyan),B(blue),andM(magenta).C.M.S.-SATURATIONAdjustscolorvividnesswith6colorsofR(red),Y(yellow),G(green),C(cyan),B(blue),andM(magenta).C.M.S.-VALUEAdjustscolorbrightnesswith6colorsofR(red),Y(yellow),G(green),C(cyan),B(blue),andM(magenta).

TIPS

• WhenFLESHTONEissettoLOWorHIGH,C.M.S.-HUE/ -SATURATION/-VALUEcannotbeset.

Adjustments for PC screen displaynAutomatic adjustmentWhenyouusethePCD-subinputterminalorPCRGBinputterminalstodisplayaPCscreenforthefirsttime,orwhenyouchangethesettingofthePC,usetheautomaticscreenadjustment.1. Switch the input to PC D-SUB or to PC RGB and display

the adjustment pattern. (See the description below.)2. Press MENU and use or to display the SCREEN

menu.3. Press and select “AUTO”.4. Press . Theautomaticadjustmentiscompleteinseveralseconds.5. Press MENU twice to close the menu screen.

TIPS

• Ifthescreencannotbeadjustedproperlywithoneautomaticadjustment,repeattheautomaticadjustmenttwoorthreetimes.Trymanualadjustmentifnecessary.

nScreen display for adjustmentBeforemakingadjustmentsintheSCREENmenuorPICTUREmenu,displayanimagetobrightentheentirescreen.IfyouareusingaWindowsPC,usetheadjustmentpatternonthesuppliedCD-ROM.

Opening the adjustment patternThefollowingexampleisperformedinWindows7.1. Load the supplied CD-ROM into the computer’s CD-

ROM drive.2. Open [CD Drive] in [Computer]. InWindowsXP,open[CDDrive]in[MyComputer].3. Double-click [Adj_uty.exe] in the [Monitor] folder. Theadjustmentpatternwillappear. Adjustthescreenautomaticallyormanually.

4. When adjustment is finished, press the [Esc] on the computer’s keyboard to quit the adjustment program.

5. Eject the CD-ROM from the CD-ROM drive.

TIPS

• Ifthedisplaymodeonthecomputeryouareusingis65,000colors,thecolorlevelsinthecolorpatternmayappear differently or grayscale may appear to be colored. (Thisisduetothespecificationsoftheinputsignalandisnot a malfunction.)

Menu Items

31 E

Youcanreturnthesettingstotheirfactory-presetvaluesandrestrict operations.

1. Hold SIZE down until “F” appears in the upper left corner of the screen.

2. While “F” appears, press , , , in that order.

▲

▲▲

▲▲

▲▲

▲ ▲

▲▲

▲▲

▲▲

OFF

UNLOCKEDON1ONLEDOFF

MONITOR

FUNCTION 1/1

ALL RESETADJUSTMENT LOCKADJUSTMENT LOCK TARGETRS-232COSD DISPLAYLEDTEMPERATUREALERTSTATUSALERTPOWER BUTTONCONTROLLER INPUT

END…[MENU]

3. Select and set the items.ALL RESETResets the settings to the factory default settings. Press ,selectALLRESET,andthenpressMENU .Afterinitialization,turnthemainpowerswitchoffandthen back on.WhenthePN-ZB01(optional)isattached,press , select the resetting method, and then press

MENU.

ALLRESET1 ....Resets all the settings to the factory default settings.

ALLRESET2 ....Returns all settings to the factory default settings except for the following items: LANSETUP,RS-232C/LANSELECT,IDNo.SET,BAUDRATE,NETWORK,MAIL,SERVICE&SUPPORT,andSNMP (See page 26, and pages 47 to 50.)

ADJUSTMENT LOCKYou can disable operations on the monitor and the remote control unit that use buttons.OFF ...Enablesoperation.ON1 ..Disablesalloperationsotherthanturningpower

on/offandFUNCTION.ON 2 ..OnlytheFUNCTIONoperationisenabled.

DisablesalloperationsotherthanFUNCTION(noteven power on/off).

ADJUSTMENT LOCK TARGETSets the target to prohibit operation of with ADJUSTMENTLOCK.REMOTECONTROL ..... Prohibits remote control

operationMONITORBUTTONS ... Prohibits monitor button

operationBOTH ............................. Prohibits remote control and

monitor button operationRS-232C(RS-232C/LAN when the PN-ZB01 (optional) is attached)SpecifieswhethertoallowcontrolviaRS-232CorLAN(see pages 32 and 43).

Initialization (Reset)/Functional Restriction Setting (FUNCTION)OSD DISPLAYShows/hides the menu, modes, and messages.TheFUNCTIONscreencannotbehidden.ON1 .............. Shows all menus, modes and messages.ON 2 .............. Hidesmessagesautomaticallydisplayed

by the display. Shows messages during operation.

OFF ............... Hidesallmenus,modesandmessages.LEDSpecifieswhethertolightthepowerLED.OFFcannotbeselectedwhenSTANDBYMODEisLOWPOWER.TEMPERATURE ALERTSelectsthenotificationmethodforanabnormaltemperature.OFF ..............Donotnotifyaboutanabnormal

temperature.OSD&LED ..Whenanabnormaltemperatureis

detected,thepowerLEDflashesinredand green alternately and the screen displaysamessage:TEMPERATURE.

LED...............Whenanabnormaltemperatureisdetected,thepowerLEDflashesinredand green alternately.

STATUS ALERTSelectsthenotificationmethodforahardwareerror.OFF ..............Donotnotifyabouttheerror.OSD&LED ..Whenahardwareerrorisdetected,the

powerLEDflashesinredandthescreendisplaysamessage:STATUS[xxxx].

LED...............Whenahardwareerrorisdetected,thepowerLEDflashesinred.

POWER BUTTONNormally, leave this setting as MONITOR.Whenusinganoptionalpart,ifinstructionappears,change the setting accordingly.CONTROLLER INPUTNormally, you do not need to change this setting.Whenusinganoptionalpart,ifinstructionappears,change the setting accordingly.

4. Press MENU to return to the normal screen.

TIPS

• Whenbothabnormaltemperatureandhardwareerroraredetected,thehardwareerrornotificationoverrides.

• IfTEMPERATUREALERTorSTATUSALERTissettoOSD&LED,alertmessageswillappeareveniftheOSDDISPLAYissettoON2orOFF.

32E

Controlling the Monitor with a PC (RS-232C)YoucancontrolthismonitorfromaPCviaRS-232C(COMport)onthePC.You can also connect multiple monitors via a daisy chain by usingaPC.ByassigningIDnumberstoeachmonitor(seepage33),youcanmakeinputmodeselection/adjustmentorcancheckthestatusofaspecificmonitor.

Precautions when the PN-ZB01 (optional) is attached• TocontrolthemonitorviaRS-232C,setRS-232C/LANSELECTtoRS-232C.

• YoucannotuseRS-232CandLANcontrolsimultaneously.

PC connectionnOne-to-one connection with a PCConnectwithRS-232straightcablebetweenthePC’sCOMport(RS-232Cconnector)andtheRS-232Cinputterminalonthe monitor.

RS-232 straight cable(commercially available)

To COM port

PC

RS-232C input terminal

nDaisy chain connection… Advanced operationConnectwithRS-232straightcablebetweenthePC’sCOMport(RS-232Cconnector)andtheRS-232Cinputterminalonthefirstmonitor.Next,connectRS-232straightcabletothefirstmonitor’sRS-232Coutputterminalandtothesecondmonitor’s RS-232Cinputterminal.Connectinthesamewaytothethirdandsubsequentmonitors.Upto25monitorscanbeconnected.(Dependingonthelength of the cable used and the surrounding environment.)

To COM portRS-232 straight cables(commercially available)

PC

First monitor Second monitor

RS-232Cinput terminal

RS-232Coutput terminal

Communication conditionsSettheRS-232CcommunicationsettingsonthePCtomatchthe monitor’s communication settings as follows:

Baudrate * Stop bit 1bit

Datalength 8 bits Flowcontrol None

Parity bit None

*SettothesamebaudrateastheBAUDRATEsettingofSETUPmenu.(Initialsetting:38400bps)

*Whenconnectingmultiplemonitorsinadaisychain,setallmonitorstothesameBAUDRATE.

Communication procedurenCommand formatWhenacommandissentfromthePCtothemonitor,themonitor operates according to the received command and sendsaresponsemessagetothePC.

C1 C2 C3 C4 P1 P2 P3 P4

Return code

Command field (4 prescribed

alphanumerical characters)

Parameter field (4 character string comprised of:

0-9, +, -, space, ?)

Example:VOLM0030 VOLM 30

* Besuretoinput4charactersfortheparameter.Padwithspaces (“ ”) if necessary. (“ ”isareturncode(0DH,0AHor0DH))Wrong :VOLM30Right :VOLM 30

Wheninputtinganegativevalue,specifyanumericalvalueinthree digits.

Example:AUTR-005

DonotusespacesforMPOS,DATE,andSC01throughSC08.Specifyparametersusingaspecifiednumberofcharacters.

Example:MPOS010097

Ifacommandhas“R”listedfor“DIRECTION”inthe “RS-232Ccommandtable”onpage36,thecurrentvaluecanbe returned by using “?” as the parameter.

Example:

VOLM???? ← FromPCtomonitor(Howmuchis current volume setting?).

30 ← FrommonitortoPC(Currentvolumesetting:30).

* IfanIDnumber(seepage33)hasbeenassigned (Forexample,IDnumber=1).

VOLM ? ← FromPCtomonitor.

30 001 ← FrommonitortoPC.

33 E

Controlling the Monitor with a PC (RS-232C)

nResponse code formatWhen a command has been executed correctly

O K Return code(0DH, 0AH)

A response is returned after a command is executed.* IfanIDnumberhasbeenassigned

O K SPC 0 0 1

ID number of responding monitor

Space (20H) Return code(0DH, 0AH)

When a command has not been executed

R R E Return code(0DH, 0AH)

* IfanIDnumberhasbeenassigned

R R E SPC 0 0 1

ID number

Space (20H) Return code(0DH, 0AH)

TIPS

• “ERR”isreturnedwhenthereisnorelevantcommandorwhen the command cannot be used in the current state of the monitor.

• IfcommunicationhasnotbeenestablishedforreasonssuchasabadconnectionbetweenthePCandmonitor,nothingisreturned(notevenERR).

• “ERR”maybereturnedwhenacommandcannotbereceived correctly due to interference from the surrounding environment. Please ensure that the system or software retries the command if this occurs.

• IfnomonitorhasbeenassignedthedesignatedIDnumber(e.g.ifthecommandIDSL0002 is used, but no monitor withIDnumber:2isfound),noresponseisreturned.

If execution of the command is taking some time

I W T A Return code(0DH, 0AH)

Whenthefollowingcommandsareused,“WAIT”isreturned.Inthiscase,avaluewillbereturnedifyouwaitawhile.Donotsend any command during this period.NoIDnumberisattachedtoWAITresponse.• CommandswhichreturnWAIT:1. Whenrepeatercontrolisused2. WhenanIDSLorIDLKcommandisused3. Whenoneofthefollowingcommandsisused:RSET,

INPS,ASNC,WIDE,PXSL,POWR,AGIN,MWIN,MWIP,MWPP

When control via RS-232C is locked (to prevent use) using the operation lock function (see page 31)

E C D K O L Return code(0DH, 0AH)

When RS-232C/LAN SELECT is set to LAN

U N S E L E C T E D

Return code(0DH, 0AH)

nCommunication interval• AfterOKorERRisreturned,youmustsendthefollowing

commands. Tosetatimeoutforthecommandresponse,specify10

seconds or longer. Whenconnectingmultiplemonitorsinadaisychain,setthetimeout to at least the product of the monitor’s position from thecomputermultipliedby10seconds. Example)3rdmonitorfromcomputer:30secondsorlonger.

• Provideanintervalof100msormorebetweenthecommand response and the transmission of the next command.

VOLM0020OK

INPS0001WAITOK

Interval of 100 ms or more

TIPS

• WhenexecutingALLRESET,setthetimeoutperiodto30seconds or longer.

• WhenturningthepoweronwhilethePOWERONDELAYfunctionisinuse,setthetimeoutperiodtothePOWERONDELAYperiod+10secondsorlonger.

Advanced operationThis section explains commands for daisy chain connection. The basic communication procedure is the same as in the “One-to-oneconnectionwithaPC”section.

nID numbersYoucanassignauniqueIDnumbertoeachmonitor(seepage 26). This allows you to control a particular monitor in a daisy chain of monitors.YoucanassignIDnumberseitherfromthemenuscreenorfromthePCusingRS-232cable.

[Example] ID number: 1 ID number: 2 ID number: 3 ID number: 4

If monitors are connected as shown above, you can execute commands like “Set the volume of the monitor with ID4to20”.

WhendesignatingIDnumbersforasetofmonitorslinkedinadaisychain,youshouldbasicallyavoidanyduplicationofIDnumbers.IDnumbersdonothavetobeassignedinascendingorderstartingfromthePC.Theycanalsobeconnectedasshownbelow.

[Example] ID number: 3 ID number: 2 ID number: 4 ID number: 1

34E

Controlling the Monitor with a PC (RS-232C)

nCommands for ID controlThe command examples shown on this page assume the followingconnectionandIDnumbersetup.

ID number: 1 ID number: 2 ID number: 3 ID number: 4

IDST .........AmonitorreceivingthiscommandsetsitsownIDnumberintheparameterfield.

Example:

IDST0001

OK 001 ← TheIDnumberofthismonitorissetto1.

TIPS

YoucanautomaticallyassignIDnumbersbyusingtheIDSTcommand with the Repeater control (see “Repeater control” onpage35).Forexample,usingthecommand“IDST001+”automaticallysetstheIDnumbers,asshownbelow.

[Example] ID number: 1 ID number: 2 ID number: 3 ID number: 4

IDST001+ ← IDsettingcommandwithrepeatercontrol

WAIT

OK 001 ← “OK”responsefromIDnumber:1

OK 002 ← “OK”responsefromIDnumber:2

OK 003 ← “OK”responsefromIDnumber:3

OK 004 ← “OK”responsefromIDnumber:4(End)

IDSL ........TheparameterofthiscommandsetstheIDnumberofthemonitor.Themonitorissubjecttothenextcommand.

Example:

IDSL0002 ← The next command is for the monitor withIDnumber:2.

WAIT ← SearchingformonitorwithIDnumber:2

OK 002 ← FoundmonitorwithIDnumber:2

VOLM0030 ← SetsvolumeofmonitorwithIDnumber:2to30.

WAIT ← Processing

OK 002 ← OKresponsefrommonitorwithIDnumber: 2

VOLM0020 ← Setsvolumeto20.

OK 001 ←ThevolumeofthemonitorwithIDnumber:1(theonedirectlyconnectedtothePC)issetto20.*

* TheIDSLcommandiseffectiveonlyonce,fortheimmediately succeeding command.

IDLK ........TheparameterofthiscommandsetstheIDnumberofthemonitor.Themonitorissubjecttoallsubsequentcommands.

Example:

IDLK0002 ← FollowingcommandsareforthemonitorwithIDnumber:2.

WAIT ← SearchingformonitorwithIDnumber:2

OK 002 ← FoundmonitorwithIDnumber:2

VOLM0030 ← SetsvolumeofmonitorwithIDnumber:2to30.*

WAIT ← Processing

OK 002

VOLM0020 ← SetsvolumeofmonitorwithIDnumber:2to20.*

WAIT

OK 002

IDLK0000 ← CancelingfixedIDnumbersetting

WAIT ← CancelingIDLK

OK 002 ← Cancelationcomplete

VOLM0010

OK 001 ←ThevolumeofthemonitorwithIDnumber:1(theonedirectlyconnectedtothePC)issetto10.(IDLKiscanceled.)

* TheIDLKcommandremainseffectiveuntilitiscanceled, or power is shut off.

IDCK ........ProvidesscreendisplayoftheIDnumbercurrentlyassignedtoamonitor,andtheIDnumbercurrentlysetforIDLK(ifany).

Example:

(AfterexecutingIDLK0002)

IDCK0000 ← (Parameter has no meaning.)

ID:001IDLK:002 ←Returnedresponse.TheIDnumber is also displayed on the monitor screen.

IDCK000+ ← Repeater control. (If a command isusedwithrepeatercontrol,IDdesignationusingIDSLorIDLKis canceled.)

WAIT

ID:001IDLK:000

ID:002IDLK:000

ID:003IDLK:000

ID:004IDLK:000

35 E

Controlling the Monitor with a PC (RS-232C)

nRepeater controlThis system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. You can use Repeater controlfunctionwithoutassigningIDnumbers.

[Example] Set 1

Set 2 Set 3 Set 4

* Ifmonitorsareconnectedasshownabove,youcanexecute a command like “Set all monitors’ input settings to PCD-SUB”.

nRepeater control commandRepeatercontrolisachievedbysettingtheFOURTHCHARACTERoftheparameterto“+”.

Example:

VOLM030+ ← Setsvolumeofallmonitorsto30.

In repeater control, responses are returned by all the connected monitors.If you want to determine that a value has been returned by a specificset,assignIDnumberstoeachmonitorinadvance.Whensomemonitorsdonotreturntheirresponses,theprobable cause is that the monitors could not receive the commandorcommandprocessingisnotcomplete.Donotsend a new command.

Example: (When4monitorsareconnected,andassignedIDnumbers:1through4)

VOLM030+

WAIT

OK 001

OK 002

OK 003

OK 004 ← If 4 monitors are connected in a chain, reliable operation can be ensured by sending a new command only after a reply has been returned by 4th (last) monitor.

Repeater control can also be used for reading settings.

Example:

VOLM???+

WAIT

10 001

Volumesettingsforallmonitors are returned.

20 002

30 003

30 004

TIPS

• IfrepeatercontrolisusedduringIDdesignation(IDSL,IDLK),theIDdesignationiscanceled.

Setting of the GAMMA user datanTo transfer the GAMMA user dataUsetheuserdatatransfercommands(UGRW,UGGWandUGBW).ForeachoftheR,GandBcolors,dividethetotal512piecesofuserdatainto16blocks,andtransfer32piecesof data with each command.

C1 C2 C3 C4 P1 P2 P3 P4 … S1 S2

Command field Block number (01 to 16) Data field Checksum field

Example:Totransferthedataofblock1(0to31levels)of red (R) data

UGRW01000000010002 … 0031C0

Command Block number 32 pieces of data Checksum

One piece of data consistsof 4 digits.

* Ifdataislessthan4digits,adda“0”(zero)tomakeit4digits.

* Thechecksumfieldisthecharacterstring(ASCII)dataoflower-orderonebytewhichindicatesthesumoftheblocknumberand32piecesofdatainhexadecimal(0toF).

nSaving the GAMMA user dataUsetheuserdatasavecommand(UGSV)tosavethetransferred user data in the monitor.If the data is not saved, it will be cleared when:• Themainpowerswitchisoff• STANDBYMODEisLOWPOWERandthemonitorenters

standby mode

nActivating the GAMMA user dataToactivatethetransferreduserdata,selectUSERforGAMMAofthePICTUREmenu,orsendthecorrespondingRS-232Ccommand.

nChecking the GAMMA user dataUsetheuserdatareadcommands(UGRR,UGGRandUGBR)toreturn512piecesofuserdataforeachoftheR,GandBcolors.Dividethedatainto16blocksandreturn32pieces of data with each command. The value to be returned is not the value stored in the monitor, but the value in the temporary memory for display. (These values are the same whentheuserdatasavecommand(UGSV)abovehasbeensent.)

TIPS

• TheuserdataisnotinitializedbyRESETofthePICTUREmenu.Toinitializetheuserdata,useALLRESEToftheFUNCTIONmenu. TheGAMMAuserdatainitializecommand(UGRS)allowstheinitializationoftheuserdataonly.

36E

RS-232C command tableHow to read the command table

Command: Commandfield(Seepage32.)Direction: WWhenthe“Parameter”issetintheparameterfield(seepage32),thecommandfunctionsasdescribed

under“Control/ResponseContents”. R The returned value indicated under “Reply” can be obtained by setting “????”, “ ?”or“???+”

(repeatercontrol)intheparameterfield(seepage32).Parameter: Parameterfield(Seepage32.)Reply: Response (Returned value)*1: “●”indicatesacommandwhichcanbeusedinpowerstandbymoderegardlessoftheSTANDBYMODEsetting. “○”indicatesacommandwhichcannotbeusedinpowerstandbymodewhenSTANDBYMODEissettoLOWPOWER.

“–”indicatesacommandwhichcannotbeusedinpowerstandbymoderegardlessoftheSTANDBYMODEsetting.*2: PN-ZB01(optional)limitations (A)WhenPN-ZB01(optional)isnotattached,(B)WhenPN-ZB01(optional)isattached. ○:Thecommandcanbeused. - :Error(ERR)

Power control/Input mode selectionFunction Command Direction Parameter Reply Control/Response contents *1

*2

(A) (B)POWERCONTROL POWR W 0

Switches to standby mode.

● ○ ○1 Returns from standby mode.

R 0 Standby mode1 Normal mode2 Input signal waiting mode

INPUTMODESELECTION INPS W 0 Togglechangeforinputmode.TerminalsnotselectedinINPUTSELECTcannot be selected.

●

○ ○1 PCDVI-D

“ERR”whenAVDVI-DisselectedforDVIofINPUTSELECT. - ○2 PCD-SUB

“ERR”whenotherthanPCD-SUBisselectedforD-SUBofINPUTSELECT. ○ ○3 AVCOMPONENT(BNC)/AVCOMPONENT(D-SUB)

“ERR”whenotherthanPCRGBisselectedforBNCofINPUTSELECT,andwhenotherthanAVCOMPONENTisselectedforD-SUBofINPUTSELECT.

○ ○

4 AVVIDEO(BNC)/AVVIDEO(D-SUB) ○ ○6 PCRGB

“ERR”whenAVCOMPONENTisselectedforBNCofINPUTSELECT. - ○7 AVDVI-D

“ERR”whenPCDVI-DisselectedforDVIofINPUTSELECT. - ○8 AVS-VIDEO - ○9 AVHDMI

“ERR”whenPCHDMIisselectedforHDMIofINPUTSELECT. ○ ○10 PCHDMI

“ERR”whenAVHDMIisselectedforHDMIofINPUTSELECT. ○ ○R 1 PCDVI-D

● ○ ○

2 PCD-SUB3 AVCOMPONENT4 AVVIDEO6 PCRGB7 AVDVI-D8 AVS-VIDEO9 AVHDMI10 PCHDMI

Controlling the Monitor with a PC (RS-232C)

37 E

SCREEN menuFunction Command Direction Parameter Reply Control/Response contents *1

*2(A) (B)

Auto ASNC W 1 When the input mode is PC D-SuB, PC RGB.

- ○ ○

CLoCK CLCK WR 0-1200 0-1200 When the input mode is PC D-SuB, PC RGB. Varies depending on the signal.

PHASE PHSE WR 0-63 0-63 When the input mode is PC D-SuB, PC RGB.PoSitioNiNG PoSitioN of

tHE LoNGESt DiRECtioN

HPoS WR 0-100 0-100 0-800 on PC D-SuB, PC RGB.Varies depending on the signal.

PoSitioN of tHE SHoRtESt DiRECtioN

VPoS WR 0-100 0-100 0-200 on PC D-SuB, PC RGB.Varies depending on the signal.

SizE SizE of tHE LoNGESt DiRECtioN

HSiz WR 0-100 0-100

SizE of tHE SHoRtESt DiRECtioN

VSiz WR 0-100 0-100

RESoLutioN LoNGESt DiRECtioN RESoLutioN

HRES WR 300-1920 300-1920 When the input mode is PC D-SuB, PC RGB. only even numbers are valid for parameters. Varies depending on the signal.

SHoRtESt DiRECtioN RESoLutioN

VRES WR 200-1200 200-1200

RESEt ARSt W 1

Controlling the Monitor with a PC (RS-232C)

38E

PICTURE menuFunction Command Direction Parameter Reply Control/Response contents *1

*2(A) (B)

AUTO AGIN W 1 WhentheinputmodeisPCD-SUB,PCRGB. -

○

○

ANALOGGAIN ANGA WR 0-127 0-127 WhentheinputmodeisPCD-SUB,PCRGB.

○

ANALOGOFFSET ANOF WR 0-127 0-127 WhentheinputmodeisPCD-SUB,PCRGB.CONTRAST CONT WR 0-60 0-60BLACKLEVEL BLVL WR 0-60 0-60TINT TINT WR 0-60 0-60COLORS COLR WR 0-60 0-60SHARPNESS SHRP WR 0-24 0-24RGBINPUTRANGE(AVHDMI) AHDR WR 0-2 0-2 0:AUTO,1:FULL,2:LIMITEDRGBINPUTRANGE(PCHDMI) PHDR WR 0-2 0-2 0:AUTO,1:FULL,2:LIMITEDRGBINPUTRANGE(AVDVI) ADVR WR 1-2 1-2 1:FULL,2:LIMITEDRGBINPUTRANGE(PCDVI) PDVR WR 1-2 1-2 1:FULL,2:LIMITEDRGBINPUTRANGE(D-SUB) PDSR WR 1-2 1-2 1:FULL,2:LIMITEDRGBINPUTRANGE(PCBNC) PBRR WR 1-2 1-2 1:FULL,2:LIMITEDADVANCED(WhentheinputmodeisAV.)

FLESHTONE FLES WR 0-2 0-2 0:OFF,1:LOW,2:HIGH

○

○

3D-NR TDNR WR 0-2 0-2 0:OFF,1:LOW,2:HIGHMPEG-NR MPNR WR 0-1 0-1 0:OFF,1:ON3D-Y/C YCSP WR 0-1 0-1 0:OFF,1:ON(WhentheinputmodeisAVVIDEO)C.M.S.-HUE CMHR WR -10-10 -10-10 R

CMHY YCMHG GCMHC CCMHB BCMHM MCRST W 1 Resets the hue.

C.M.S.-SATURATION

CMSR WR -10-10 -10-10 RCMSY YCMSG GCMSC CCMSB BCMSM MCRST W 2 Resets the saturation.

C.M.S.-VALUE CMVR WR -10-10 -10-10 RCMVY YCMVG GCMVC CCMVB BCMVM MCRST W 3 Resets the brightness.

COLORMODE BMOD WR 0 0 STD

○2 2 VIVID3 3 sRGB(WhentheinputmodeisPC)

WHITEBALANCE THRU CTMP WR 0 0 WhentheinputmodeisPCDVI-D/PCHDMI.

○

PRESET 1-18 1-18 From1:approximately3,000Kto15:approximately10,000K(500Ksteps)16:approximately5,600K,17:approximately9,300K, 18:approximately3,200K

USER 99 99R-CONTRAST CRTR WR 0-256 0-256 “ERR”whenCTMPisnotsetto99.G-CONTRAST CRTG WR 0-256 0-256B-CONTRAST CRTB WR 0-256 0-256R-OFFSET OFSR WR -127-127 -127-127G-OFFSET OFSG WR -127-127 -127-127B-OFFSET OFSB WR -127-127 -127-127

COPYTOUSER CPTU W 0 Copiesapresetvaluetotheusersetting. -GAMMA GAMM WR 0-2 0-2 0:1.8,1:2.2,2:2.4(duringPCinput)

0:LIGHT2,2:DARK(duringAVinput)

○

4-6 4-6 4: USER,5:2.0,6:STD(duringPCinput)4:USER,5:LIGHT1,6:STD(duringAVinput)

DISPLAYCOLORPATTERN PTDF WR 0 0 No pattern display.1 1 Whitesinglecolorpatterndisplay.2 2 Red single color pattern display.3 3 Greensinglecolorpatterndisplay.4 4 Bluesinglecolorpatterndisplay.

99 99 Red/green/blue mixed color pattern display.Seteachcolor'slevelwithRED,GREEN,BLUE.

RED PTDR WR 0-15 0-15 “ERR”whenPTDFisnotsetto99.GREEN PTDG WR 0-15 0-15BLUE PTDB WR 0-15 0-15RESET ARST W 2 -

Controlling the Monitor with a PC (RS-232C)

39 E

AUDIO menuFunction Command Direction Parameter Reply Control/Response contents *1

*2

(A) (B)

TREBLE AUTR WR -5-5 -5-5

○ ○ ○BASS AUBS WR -5-5 -5-5

BALANCE AUBL WR -10-10 -10-10

RESET ARST W 3 -

SETUP menuFunction Command Direction Parameter Reply Control/Response contents *1

*2(A) (B)

OSD H-POSITION OSDH WR 0-100 0-100 ○

○ ○

OSD V-POSITION OSDV WR 0-100 0-100SCREEN MOTION SCSV WR 0-4 0-4 0: OFF, 1-4: PATTERN1-4 ○MOTION TIME 1 MTIM WR 0-20 0-20 ○MOTION TIME 2 PATTERN1 MINT WR 10-990 10-990 Per 10 seconds ○

PATTERN2-4 MINT WR 5-20 5-20 Per secondMONAURAL AUDIO MONO WR 0-1 0-1 0: OFF, 1: ON ○LANGUAGE LANG WR 14 14 ENGLISH

○

1 1 DEUTSCH2 2 FRANÇAIS3 3 ITALIANO4 4 ESPAÑOL5 5 РУССКИЙ6 6

POWER ON DELAy PWOD WR 0 0 OFF ○1-60 1-60 ON

STANDBy MODE STBM WR 0-1 0-1 0: STANDARD, 1: LOW POWER(“ERR" when SCHEDULE is effective or OFF is selected for LED.) ○

OFF IF NO OPERATION ATOF WR 0-1 0-1 0: OFF, 1: ON ○HOT PLUG CONTROL (DVI) HPCT WR 0-1 0-1 0: OFF, 1: ON ○ - ○HOT PLUG CONTROL (HDMI) HPCH WR 0-1 0-1 0: OFF, 1: ON ○ ○ ○RS-232C/LAN SELECT CTLS WR 0-1 0-1 0 : RS-232C 1 : LAN ○ - ○ID NUMBER ID NO. SETTING IDST W 0-255 Sets the monitor’s ID number. (“0” means “no ID number”.)

○ ○ ○

R 0-255 Returns the monitor’s ID number.ID NO. SETTING (ONCE)

IDSL W 1-255 Sets a monitor ID number.This ID number is only effective for the command immediately after this command.

0 Clears the ID number if one has been designated.ID NO. SETTING (SUBSEQUENT)

IDLK W 1-255 Sets a monitor ID number. This ID number is effective for the next and all subsequent commands after this command.

0 Clears the ID number if one has been designated.ID CHECK IDCK W 0 ID : xxx

IDLK : yyyDisplays monitor’s own ID number and the selected ID number on the screen.

ID DISPLAy IDDP W 0-2 0: OFF, 1: ON, 2: ON (turns OFF after 4 sec.)(When the PN-ZB01 is attached, the IP address and MAC address are both displayed.)

BAUD RATE BAUD WR 0-2 0-2 0: 9600bps, 1: 19200bps, 2: 38400bps ○ ○ ○SPEAKER SELECT SPSL WR 0-1 0-1 0: Internal speaker, 1: External speaker ○ - ○HDMI AUTO VIEW HDAW WR 0-1 0-1 0: OFF, 1: ON ○ ○ ○SETTING COPy MODE CPMD WR 0 0 Copy to all monitors.

○ ○ ○1-225 1-225 Copy to the monitor with the set ID Number.

SETTING COPy TARGET CPTG WR 0 0 Copies the PICTURE menu settings.1 1 Copies all the settings.

LOGO SCREEN BTSC WR 0-1 0-1 0: OFF, 1: ON

Controlling the Monitor with a PC (RS-232C)

40E

Controlling the Monitor with a PC (RS-232C)

OPTION menuFunction Command Direction Parameter Reply Control/Response contents *1

*2(A) (B)

DatE/timE sEtting DatE WR aaBBCCDDEE aaBBCCDDEE aa: Year, BB: month, CC: Day, DD: Hour, EE: minute

○ ○ ○

DatE DisPLaY FORmat DtFt WR 0-2 0-2 0: YYYY/mm/DD, 1: mm/DD/YYYY, 2: DD/mm/YYYYYYYY: Year, mm: month, DD: Day

timE DisPLaY FORmat tmFt WR 0-1 0-1 0: 24-HOUR timE, 1: 12-HOUR timE

sCHEDULE sC01-sC08

WR aBCDEFFggH aBCDEFFggH Schedule of a specified numbera: schedule 0= not effective, 1 = EffectiveB: Power 0 = OFF, 1 = OnC: Day of the week 1 0 = Only once, 1 = Every week, 2 = Every dayD: Day of the week 2 0 = sunday, 1 = monday through 6 = saturday, 9 = not existE: Day of the week 3 0 = sunday, 1 = monday through 6 = saturday, 9 = not existF: Hour 00-23g: minute 00-59H: Input 0 = Not specified, 1 = PC DVI-D/AV DVI-D,

2 = PC D-SUB, 3 = PC RGB/AV COMPONENT, 4 = AV VIDEO, 5 = AV S-VIDEO, 6 = PC HDMI/AV HDMI

“ERR” when LOW POWER is selected for stanDBY mODE.sCHEDULE BRigHtnEss sB01-

sB08WR 0-31 0-31 Screen brightness to change

99 99 Disable brightness settinginPUt sELECt DVI DVSL WR 0-1 0-1 0: PC DVI-D, 1: AV DVI-D ○ -

○

BnC BnsL WR 0-1 0-1 0: PC RGB, 1: AV COMPONENT ○ -D-sUB sLDs WR 0-2 0-2 0: PC D-SUB, 1: AV COMPONENT, 2: AV VIDEO ○ ○HDmi HDsL WR 0-1 0-1 0: PC HDMI, 1: AV HDMI ○ ○

aUDiO sELECt PC DVI-D asDP WR 1-3 1-3 1: aUDiO(stEREO mini), 2: aUDiO1(RCa), 3: aUDiO2(RCa)

○

-PC HDmi asHP WR 0-1 0-1 0: HDmi, 1: aUDiO(stEREO mini) ○

2-3 2-3 2: aUDiO1(RCa), 3: aUDiO2(RCa) -PC D-sUB asaP WR 1-3 1-3 1: aUDiO(stEREO mini) ○

2: aUDiO1(RCa), 3: aUDiO2(RCa) -PC RgB asCP WR 1-3 1-3 1: aUDiO(stEREO mini), 2: aUDiO1(RCa), 3: aUDiO2(RCa) -AV DVI-D asDa WR 1-3 1-3 1: aUDiO(stEREO mini), 2: aUDiO1(RCa), 3: aUDiO2(RCa) -AV HDMI asHa WR 0-1 0-1 0: HDmi, 1: aUDiO(stEREO mini) ○

2-3 2-3 2: aUDiO1(RCa), 3: aUDiO2(RCa) -AV COMPONENT (BnC)

asCa WR 1-3 1-3 1: aUDiO(stEREO mini), 2: aUDiO1(RCa), 3: aUDiO2(RCa)-

AV COMPONENT (D-sUB)

asC2 WR 1-3 1-3 1: aUDiO(stEREO mini), 2: aUDiO1(RCa), 3: aUDiO2(RCa) ○AV S-VIDEO assa WR 1-3 1-3 1: aUDiO(stEREO mini), 2: aUDiO1(RCa), 3: aUDiO2(RCa) -AV VIDEO (BNC) ASVA WR 1-3 1-3 1: aUDiO(stEREO mini), 2: aUDiO1(RCa), 3: aUDiO2(RCa) -AV VIDEO (D-SUB) ASV2 WR 1-3 1-3 1: aUDiO(stEREO mini), 2: aUDiO1(RCa), 3: aUDiO2(RCa) ○

inPUt REsOLUtiOn (PC)

REsOLUtiOn CHECK PXCK R - Returns current resolution in the form of hhh, vvv.

-

○ ○

PiXEL sEtting (PC D-sUB, PC RgB)

PXsL WR 1 1 768) 1360 x 7682 2 768) 1280 x 7683 3 768) 1024 x 7685 5 480) 848 x 4806 6 480) 640 x 4807 7 1050) 1680 x 10508 8 1050) 1400 x 10509 9 768) aUtO

10 10 480) aUtOINPUT RESOLUTION (AV) REsOLUtiOn CHECK REsO R - 480i, 480p, 1080i, 720p, 1080p, VGA , etc. -ZOOm2 sPECiaL sEtting (PC D-sUB, PC RgB)

Z2sP WR 0-1 0-1 0: OFF, 1: On ○sCan mODE sCan WR 0-2 0-2 0: MODE1, 1: MODE2, 2: MODE3 (When the input mode is AV) ○POWER managEmEnt (PC) Pmng WR 0-1 0-1 0: OFF, 1: On ○POWER MANAGEMENT (AV) PMAV WR 0-1 0-1 0: OFF, 1: On ○COLOR sYstEm CsYs WR 0-5 0-5 0: aUtO, 1: PaL, 2: PaL-60, 3: sECam, 4: ntsC3.58, 5: ntsC4.43 ○ ○ ○aUDiO OUtPUt(RCa) aOUt WR 0-2 0-2 0: VARIABLE1, 1: FIXED, 2: VARIABLE2 ○

○ ○AUDIO LEVEL(STEREO MINI) AIVP WR 0-1 0-1 0: 1.0Vrms, 1: 0.5Vrms ○sELF aDJUst aaDJ WR 0-1 0-1 0: OFF, 1: On ○aUtO inPUt CHangE ainC WR 0-1 0-1 0: OFF, 1: On ○tOUCH PanEL mODE gmDP WR 0-1 0-1 0: OFF, 1: ON (When the input mode is PC) ○

41 E

PIP/PbyP menuFunction Command Direction Parameter Reply Control/Response contents *1

*2(A) (B)

PIPMODES MWIN WR 0-3 0-3 0:OFF,1:PIP,2:PbyP,3:PbyP2 ○

○ ○

PIPSIZE MPSZ WR 1-64 1-64 ○PIP POS THELONGEST

DIRECTIONMHPS W 0-100 ○

R 0-100 ○THESHORTESTDIRECTION

MVPS W 0-100 ○R 0-100 ○

PIPPOSLD+SDBATCH MPOS W 0-100,0-100 Specify the position in MPOSxxxyyy format. (xxx: Longer side, yyy: Shorter side position) ○

R 0-100,0-100 Returns a response in (xxx,yyy) format. (xxx: Longer side, yyy: Shorter side position) ○

PIPBLEND MWBL WR 0-15 0-15 ○PIPSOURCE MWIP WR 1 1 PCDVI-D

○

- ○2 2 PCD-SUB ○ ○3 3 AVCOMPONENT(BNC)/AVCOMPONENT(D-SUB) ○ ○4 4 AVVIDEO(BNC)/AVVIDEO(D-SUB) ○ ○6 6 PCRGB - ○7 7 AVDVI-D - ○8 8 AVS-VIDEO - ○9 9 AVHDMI ○ ○10 10 PCHDMI ○ ○

SOUNDCHANGE MWAD WR 1-2 1-2 1:MAIN,2:SUB ○○ ○MAIN POS (Main screen) MWPP WR 0-1 0-1 0:POS1,1:POS2 ○

PbyP2 POS (Sub screen) MW2P WR 0-2 0-2 0:POS1,1:POS2,2:POS3 ○AUTOOFF MOFF WR 0-1 0-1 0:MANUAL,1:AUTO ○

Initialization/Functional Restriction Setting (FUNCTION) menuFunction Command Direction Parameter Reply Control/Response contents *1

*2(A) (B)

ALLRESET RSET W 0 0:ALLRESET - ○ -0-1 0:ALLRESET1,1:ALLRESET2 - - ○

ADJUSTMENTLOCK ALCK WR 0-2 0-2 0:OFF,1:ON1,2:ON2 ○

○ ○

ADJUSTMENTLOCKTARGET ALTG WR 0-2 0-2 0:REMOTECONTROL,1:MONITORBUTTONS,2:BOTH ○OSDDISPLAY LOSD WR 0-2 0-2 0:ON1,1:OFF,2:ON2 ○LED OFLD WR 0-1 0-1 0:ON,1:OFF

“ERR”whenLOWPOWERisselectedforSTANDBYMODE. ○TEMPERATUREALERT TALT WR 0-2 0-2 0:OFF,1:OSD&LED,2:LED ○STATUSALERT SALT WR 0-2 0-2 0:OFF,1:OSD&LED,2:LED ○POWERBUTTON PBTN WR 0-1 0-1 0:MONITOR,1:CONTROLLER ○CONTROLLERINPUT PCIP WR 0-2 0-2 0:D-SUB,1:HDMI(“ERR”whenMONITORisselectedforPOWER

BUTTON.) ○ ○ ○2:DVI-D(“ERR”whenMONITORisselectedforPOWERBUTTON.) ○ - ○

Controlling the Monitor with a PC (RS-232C)

42E

OthersFunction Command Direction Parameter Reply Control/Response contents *1

*2

(A) (B)SCREEN SIZE (PC) WIDE WR 1-5 1-5 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2 ○

○ ○

SCREEN SIZE (AV) WIDE WR 1-5 1-5 1: WIDE, 2: ZOOM1, 3: ZOOM2, 4: NORMAL, 5: Dot by Dot ○VOLUME VOLM WR 0-31 0-31 ○MUTE MUTE WR 0-1 0-1 0: OFF, 1: ON -INFORMATION MODEL INF1 R Value ●

SERIAL NO SRNO R ValueBRIGHT VLMP WR 0-31 0-31 ○TEMPERATURE SENSOR DSTA R 0 Internal temperature normal

●1 Internal temperature abnormal (Standby mode)2 Internal temperature abnormal (Temperature is normal now, but it was

abnormal during operation.)3 Internal temperature abnormal (Brightness of the backlight decreases.)4 Temperature sensor abnormal

TEMPERATURE ACqUISITION ERRT R Value Temperature at temperature sensors 1 through 3 are returned in the following forms:[Sensor 1], [Sensor 2], [Sensor 3]Indicates a temperature sensor abnormality when “126” is returned.

○

CAUSE OF LAST STANDBY MODE STCA W 0 Initialization

●

R 0 No detectable error has occurred1 Standby mode by POWER button2 Main power off by the main power switch3 Standby mode by RS-232C or LAN4 Input signal waiting mode by No Signal6 Standby mode by abnormal temperature8 Standby mode by SCHEDULE setting

20 Standby mode by OFF IF NO OPERATION setting

Commands for setting of the GAMMA user dataFunction Command Direction Parameter Reply Control/Response contents *1

*2

(A) (B)RED GAMMA DATA TRANSFER UGRW W aaxxxx ··· xxxxcc

(xxxx: 32 pieces)aa: 01-16xxxx: 0000-1023cc: 00-FF

aa: Block numberxxxx: 32 pieces of user datacc: Checksum (ASCII data) of the block number and user data

○ ○ ○

GREEN GAMMA DATA TRANSFER UGGW WBLUE GAMMA DATA TRANSFER UGBW W

RED GAMMA DATA READ UGRR W 1-16 xxxx ··· xxxx(xxxx: 32 pieces)xxxx: 0000-1023

xxxx: User data of 32 piecesGREEN GAMMA DATA READ UGGR W 1-16BLUE GAMMA DATA READ UGBR W 1-16USER DATA INITIALIZE UGRS W 0 Initialize the user data.USER DATA SAVE UGSV W 0 Save the user data in the monitor.

Controlling the Monitor with a PC (RS-232C)

43 E

WhenthePN-ZB01(optional)isattached,yourmonitorcanbeconnectedtoaLANallowingyoutocontrolitfromaPConthe LAN. Youcanalsoconfigurethemonitortosende-mailnotificationwhen it has a problem. TheconnectionrequiresacommerciallyavailableLANcable(UTPcable,Category5,straightthrough).

HubLAN terminal

LAN cable (commercially available, straight)

Network (LAN)

TIPS

• YoumustassignanIPaddresstothemonitorbyfollowingthe procedures in “Settings to connect to a LAN”. (See the description on the right.)

• YourPCmustbeinstalledwithInternetExplorer(version7.0or later).

• TocontrolthemonitorviaLAN,setRS-232C/LANSELECTto LAN. (See page 26.)

• YoucannotuseRS-232CandLANcontrolsimultaneously.

Initializing personal information• WhenthePN-ZB01(optional)isattached,personalinformationsuchase-mailaddressescanberegisteredinthemonitor.Beforetransferringordisposingofthemonitor,initializeallsettingsbyselectingALLRESET1.(Seepage31.)NotethatALLRESET2willnotinitializee-mailaddresses and other settings.

Controlling the Monitor with a PC (LAN)Settings to connect to a LANSet the monitor’s IP address and subnet mask to match the settings of your LAN. ThesesettingscanbemadeoneitherthemonitororaPCconnected to the monitor.ThesettingsdependontheconfigurationofyourLAN.Askyour LAN administrator for details.

■ To set on the monitorSetRS-232C/LANSELECTontheSETUPmenutoLAN,andthensettheLANSETUPoptions.(Seepage26.)Aftersettingeachitem,selectSETandpressMENU .

DHCP CLIENTIfyourLANhasaDHCPserverandyouwishtoobtainanaddress automatically, change this setting to ON. Tosettheaddressmanually,setthistoOFF.IP ADDRESSIftheDHCPCLIENTissettoOFF,specifyanIPaddress.Press or to select items, and press or to change the values.SUBNET MASKIftheDHCPCLIENTissettoOFF,specifythesubnetmask.Press or to select items, and press or to change the values.DEFAULT GATEWAYIftheDHCPCLIENTissettoOFF,specifythedefaultgateway. Ifyouarenotusingagateway,specify“0.0.0.0”.Press or to select items, and press or to change the values.RESETResets the values of the LAN settings to the factory preset values. Select ON and then press MENU .

TIPS

• WhentheIPaddressissetmanually,theIPaddressesofthemonitorconnectedtotheRS-232Coutputterminal and the daisy chain of connected monitors that follows can be assigned automatically. (See page 26.)

44E

■ To set from a PCWhenthemonitorisconnectedtoaPC,LANsettingscanbeconfiguredviaPC.

Set up process(1)ConnectyourmonitortoaPC(2)SpecifythePC’sIPaddress(3)Configurethemonitor’sLANsettings

(1) Connecting your monitor to a PCConnectacommerciallyavailablecrossoverLANcable(UPTcable,Category5)totheLANportonthePCandthismonitor.

LAN cable (commercially available, crossover)

To LAN terminal

PC

LAN terminal

(2) Specifying the PC’s IP addressToconfigurethemonitor’sLANsettings,youmusttemporarilychangethesettingsonthePC.ThisexplanationisbasedonWindows7.1. LogontothePCwithanadministratoraccount.2.Click[Start],andthenclick“ControlPanel”.3.Click“Viewnetworkstatusandtasks”in“Networkand

Internet”.In“ClassicView”,click“NetworkandSharingCenter”.

4.Click“LocalAreaConnection”andthen“Properties”.5.Click“InternetProtocolVersion4(TCP/IPv4)”andthen

“Properties”.6. Make a note of the current IP address, subnet mask, and

default gateway settings. Make sure you write this information now as you will be changing the IP address, subnet mask, and default gateway settings back to these settings afterwards.

7. Temporarily change the IP address and subnet mask. To access the monitor as it is shipped from the factory, set as follows. • IPAddress:192.168.150.1• SubnetMask:255.255.255.0• DefaultGateway:(leaveblank)

8.Click[OK]andthenrebootthePC.

TIPS

• Thismonitorisfactorypresetasshownbelow. (WhenDHCPCLIENTissettoOFF)

IPAddress :192.168.150.2 SubnetMask :255.255.255.0 DefaultGateway :0.0.0.0

(3) Configuring the monitor’s LAN settingsAccessthemonitorusingInternetExplorer.

Controllingthemonitor1. TurnthepowerONtothemonitor.2.SetRS-232C/LANSELECTontheSETUPmenutoLAN.3.SetDHCPCLIENTtoOFFinLANSETUPontheSETUP

menu.

PCoperation4. LaunchInternetExplorer,inthe“Address”boxtype

“http://192.168.150.2/”andpresstheEnterkey.

You will be prompted to enter a user name and password. 5. Leavetheusernameandpasswordboxesblankandclick

[OK].

Controlling the Monitor with a PC (LAN)

45 E

6.Clickon“LANSETUP”underNETWORK.

7.Specifythe“DHCPCLIENT”,“IPADDRESS”,etc.

DHCP CLIENTIfyourLANhasaDHCPserverandyouwishtoobtainanaddress automatically, change this setting to “ON”. Tosettheaddressmanually,setthisto“OFF”.IP ADDRESSIftheDHCPCLIENTissetto“OFF”,specifyanIPaddress.SUBNET MASKIftheDHCPCLIENTissetto“OFF”,specifythesubnetmask.DEFAULT GATEWAYIftheDHCPCLIENTissetto“OFF”,specifythedefaultgateway. Ifyouarenotusingadefaultgateway,specify“0.0.0.0”.

8.Whenthesettingischanged,click[Apply].9.Checkthemessageandclick[OK].10.ExitInternetExplorer.11.RestorethePC’sIPaddressjottedinStep6,“(2)

SpecifyingthePC’sIPaddress”.12.ConnectthemonitorandthePCtotheLAN.

Caution

• Wait10secondsafterclicking[OK]beforeproceeding.• Whenoperatingusingtheremotecontrolunitorsimilar,click[Refresh].

TIPS

• WhentheIPaddressissetmanually,theIPaddressesofthemonitorconnectedtotheRS-232Coutputterminalandthe daisy chain of connected monitors that follows can be assigned automatically. (See page 26.)

Controlling with a PC■ Basic operationYouuseInternetExploreronaPContheLANtocontrolthemonitor.1. LaunchInternetExploreronthePC.2. In the “Address” box, type “http://” followed by your monitor’s

IPaddressfollowedby“/”,thenpresstheEnterkey. YoucanconfirmtheIPaddresswiththeDISPLAYfunction.

Whenpromptedtoenterausernameandpassword,typetheusernameandpasswordthatyouspecifiedinthesecuritysettings(seepage47),andclick[OK].If you did not make any security settings, leave the spaces blankandclickon[OK].

3. You can check, control, and change the monitor’s status and settings by clicking the menu items on the left side of the screen.

• Ifyouseean[Apply]buttonnexttoasetting,clickitafteryou change that setting.

TIPS

• Seepages46to50fordetailsoneachsetting.• Ifyouclick[Refresh]beforethescreenfinishesupdatingthecurrentdisplay,the“ServerBusyError”willappear.Waitforamomentbeforeoperatingyourmonitoragain.

• Youcannotoperatethemonitorwhileitiswarmingup.• If“DHCPCLIENT”issetto“ON”,pressDISPLAY on the

remote control unit two times and then check the monitor’s IP address.

Controlling the Monitor with a PC (LAN)

46E

■ INFORMATIONInformation about this monitor appears.

■ CONTROLYou can control the operations corresponding to the buttons (POWER INPUT SIZE )ontheremotecontrolunit.(Seepage21.)

TIPS

• Instandbymode,PowerONistheoperationavailable.

■ ADJUSTMENTYoucanadjustthesesettingswhicharealsoavailableonthemonitor’s menu. • SCREEN(Seepage24.)• PICTURE(Seepage24.)• PICTURE(ADVANCED)(Seepage30.)• AUDIO(Seepage25.)• SETUP(Seepage25.)• OPTION(Seepage26.)• SCHEDULE(Seepage29.)• PIP/PbyP(Seepage27.)• FUNCTION(Seepage31.)

TIPS

• AfterchangingDISPLAYCOLORPATTERNtoOFF,click[Refresh]tocorrectlyretrievethestatusofthemonitor.

Controlling the Monitor with a PC (LAN)

47 E

■ NETWORK (LAN SETUP)This screen allows you to set the settings necessary when the monitor is connected to a LAN.

DHCP CLIENTIfyourLANhasaDHCPserverandyouwishtoobtainanaddress automatically, change this setting to “ON”. Tosettheaddressmanually,setthisto“OFF”.IP ADDRESSIftheDHCPCLIENTissetto“OFF”,specifyanIPaddress.SUBNET MASKIftheDHCPCLIENTissetto“OFF”,specifythesubnetmask.DEFAULT GATEWAYIftheDHCPCLIENTissetto“OFF”,specifythedefaultgateway. Ifyouarenotusingadefaultgateway,specify“0.0.0.0”.DNS SERVERSpecifytheDNSserveraddress.IfyouarenotusingaDNSserver,specify“0.0.0.0”.RESETClicking[Execute]returnsalloftheLANSETUPsettingstothefactory-presetvaluesexceptfortheDNSSERVERsetting.

TIPS

• WhentheIPaddressissetmanually,theIPaddressesofthemonitorconnectedtotheRS-232Coutputterminal and the daisy chain of connected monitors that follows can be assigned automatically. (See page 26.)

■ NETWORK (SECURITY)Thisscreenallowsyoutospecifythesecurity-relatedsettings.

USER NAME / PASSWORDSets up a user name and password to restrict access to this monitor. Afterenteringausernameandpassword,click[Apply].ACCEPT IP ADDRESSYou can limit access to this monitor by registering IP addressesofPCsthatshouldhaveaccess.Tolimitaccess,specifytheoption“FromonlyspecificIPaddresses”.Otherwise,toallowaccessfromanyPC,specify“All IP Addresses”.IP ADDRESS 1 to 3If“ACCEPTIPADDRESS”issetto“FromonlyspecificIPaddresses”, enter the IP addresses that you want to allow.

TIPS

• TheUSERNAMEandPASSWORDcanbeupto8alphanumeric characters or symbols.

• Tocanceltheusernameand/orpasswordafterithasbeenset,maketheboxemptyandclick[Apply].

Controlling the Monitor with a PC (LAN)

48E

■ NETWORK (GENERAL)This screen allows you to specify the general LAN settings.

MONITOR NAMESpecify a name for this monitor as it should appear on the InternetExplorerscreen.AUTO LOGOUT TIMESpecify the time (in minutes) to elapse before automatically disconnecting this monitor from the network. Specifyinminutesfrom1to65535.Avalueof‘0’willdisablethis function. DATA PORTSpecifytheTCPportnumbertouseforexchangingdatawiththe monitor. Specifyavaluefrom1025to65535.SEARCH PORTSpecify the port number to use when searching for this monitor. Specifyavaluefrom1025to65535.INSTALLATION INFORMATION (NAME/LOCATION)Specify the information to display for this monitor in the InternetExplorerwindow.

TIPS

• TheMONITORNAMEcanbeupto16alphanumericcharacters or symbols.

• Enterupto50charactersintheNAMEfieldintheINSTALLATIONINFORMATION.

• Enterupto100charactersintheLOCATIONfieldintheINSTALLATIONINFORMATION.

■ MAIL (ORIGINATOR) Thisscreenallowsyoutoconfigurethee-mailsentperiodicallyor when the monitor has an error.ThesettingsdependontheconfigurationofyourLAN.Askyour LAN administrator for details.

SMTP SERVERSpecifytheSMTPserveraddressforsendinge-mail.* Whenusingadomainname,makesuretospecifytheDNSSERVER as well. (See page 47.)

ORIGINATOR E-MAIL ADDRESSSpecifythee-mailaddressforthismonitor.Thisaddressbecomesthee-mailaddressoftheoriginator.ORIGINATOR NAMESpecify the name for the originator. Thisnameappearsinthe“OriginatorName”fieldofthee-mail.AUTHENTICATIONSpecify the authentication method to use when sending e-mail.POP SERVERIfthe“AUTHENTICATION”methodis“POPbeforeSMTP”,specify the POP server address. ACCOUNT NAME / PASSWORDIfthe“AUTHENTICATION”methodis“POPbeforeSMTP”,specify the account name and password to connect to the POP server.

TIPS

• Youcanenterupto64alphanumericcharactersorsymbolsfortheORIGINATORE-MAILADDRESS,ORIGINATORNAME,ACCOUNTNAME,andPASSWORD.

• TheSMTPSERVERandPOPSERVERcanbeupto64characters. Thefollowingcharacterscanbeused:a-z,A-Z,0-9,-,.

Controlling the Monitor with a PC (LAN)

49 E

■ MAIL (RECIPIENT) Thisscreenallowsyoutospecifytherecipientsofthee-mailsent periodically or when the monitor has an error.

RECIPIENT E-MAIL ADDRESSESSpecifythee-mailaddressestosenderrornotificatione-mailto.CONDITIONSpecify the conditions to send mails. WhenyoucheckPERIODICAL,specifythedateandtimetosendthemailsinthePERIODICALsetting.CONFIRMATIONSendsteste-mail.Thisallowsyoutoconfirmthatthee-mailsettingsareconfiguredproperly.Attach the log file to a TEMPERATURE/HARDWARE error e-mail.Whenthisoptionischecked,alogisaddedtothemailwhichnotifiesatemperatureorstatuserror.

TIPS

• TheRECIPIENTE-MAILADDRESSEScanbeupto64alphanumeric characters or symbols.

Controlling the Monitor with a PC (LAN)

■ MAIL (PERIODICAL)WhenPERIODICALforCONDITIONofMAIL(RECIPIENT)ischecked, set the date and time to send the mail.

DAY OF THE WEEKSpecify the day of the week to send the periodical mails.TIMESpecify the time of the day to send the periodical mails.

Caution

• Donotturnoffthemainpowerwhenyousettosendtheperiodical mails.

• Specifythecorrectdateandtime.(Seepage26.) If the date and time settings are incorrect, the periodical mail is not sent properly.

• Regularlyconfirmthatthespecifieddateandtimeiscorrect.

• WhenLOWPOWERisselectedforSTANDBYMODE,periodical mails will not be sent in standby mode.

50E

Controlling the Monitor with a PC (LAN)

■ SNMPYoucanconfiguresettingsrelatedtoSNMP.

SNMP SETTINGSet whether to enable or disable SNMP.VERSIONSet the version of the SNMP to be supported.COMMUNITY NAME 1 to 3Setthenameofthecommunityrequiredfortheaccess.USER 1 to 3Set the user name, password, authentication method and otheroptionsrequiredforaccess.TRAP SETTINGSet whether to enable or disable the trap function.Whenthisfunctionisenabled,atrapwillbesentwhenthemonitor is turned on.TRAP SETTING OF AUTHENTICATION ERRORSetwhetherthetrapfunctionsendsanotificationwhenauthentication fails.TRAP ADDRESS & PORTSet the destination address and port number of the notificationsentbythetrapfunction.

Caution

• AfteryousetSNMP,click[Switchthemainpowerofmonitoroffandonnow.]orturnoffthemonitorandthenturnitonagainwiththemainpowerswitch.Whenthemonitorrestarts,waitabout30secondsandthenstartthenext operation.

• IftheIPaddressischangedwhiletheSNMPfunctionisoperational, turn off the monitor and then turn it on again with the main power switch.

TIPS

• DependingontheSNMPsettings,ashortdelaymayoccurbefore the SNMP is usable. (About 2 minutes)

• Upto16alphanumericlettersandsymbolscanbeusedforthe community name, user name and password.

■ SERVICE & SUPPORT (URL INFORMATION)

YoucandisplayaspecificURLintheURLINFORMATIONfieldontheINFORMATIONscreenwhenanerroroccursinthe monitor. (See page 46.)

URL INFORMATIONEntertheURLtodisplayontheINFORMATIONscreenwhenan error occurs on the monitor.Up to 64 alphanumeric characters or symbols can be used.CONDITIONSpecify the condition to display the URL.CONFIRMATIONThehomepageofthespecifiedURLisdisplayed.You can check whether the URL you entered is correct.

TIPS

• Itisalsopossibletospecifythemessagetext,suchasthename of a contact or a telephone number, to be displayed instead of the linked URL.

51 E

TroubleshootingIf you are experiencing any problem with your display, before calling for service, please review the following troubleshooting tips.

There is no picture or sound.• Isthepowercorddisconnected?(Seepage14.)• Isthemainpowerswitchoff?(Seepage16.)• Isthemonitorinstandbymode(thepowerLEDilluminatinginorange)?(Seepage16.)

• Makesurecorrectinputmodeisselected.(Seepage21.)• Ifanyexternalequipmentisconnected,makesuretheequipmentisoperating(playingback).

Remote control does not work.• Arethebatteriesinsertedwithpolarity(+,-)aligned?(Seepage15.)

• Arethebatteriesexhausted?• Pointtheremotecontrolunittowardthemonitor’sremotecontrolsensor.(Seepage15.)

• Isthemenudisplayhiddenorisoperationdisabled?(Seepage31.)

Sound from left and right speakers is reversed.Sound is heard from only one side.• Areaudiocablesconnectedproperly?(Seepages12to13.)

• Makesureaudiocablesforexternalspeakersareconnected properly: left and right cables may be reversed or one of the two cables may not be connected. (See page 13.)

• CheckthesettingofBALANCEforAUDIOmenu.(Seepage25.)

There is a picture but no sound.• Isthesoundmuted?• Makesurethevolumeisnotsettominimum.• Areaudiocablesconnectedproperly?• IsthesettingofAUDIOSELECTontheOPTIONmenu

correct? (See page 26.)• IsthesettingofSPEAKERSELECTontheSETUPmenu

correct? (See page 26.)

Unstable video.• Thesignalmaybeincompatible.• TrytheautomaticscreenadjustmentwhenthePCD-subinputterminalorPCRGBinputterminalsareused.

• Ifthetopandbottomoftheimagearenothorizontallyaligned,setTOUCHPANELMODEontheOPTIONmenutoOFF.

The video from the PC/AV HDMI input terminal does not appear properly.• IsthesettingforHDMIofINPUTSELECTontheOPTION

menu correct? (See page 26.)• IstheHDMIcableHDMIstandardcompliant?Themonitor

will not work with cables that are not standard compliant.• Istheinputsignalcompatiblewiththismonitor?(Seepage55.)

The video from the PC/AV DVI-D input terminal does not appear properly.• IsthesettingforDVIofINPUTSELECTontheOPTION

menu correct? (See page 26.)• Istheinputsignalcompatiblewiththismonitor?(Seepage55.)

• Turnoffthepowertotheconnectedequipmentandthenturn the power on again.

• Ifthemonitorsareconnectedinadaisychain,turnoffthepower to all the monitors connected in a daisy chain and then turn the power on again.

The video from PC D-SUB, PC RGB, AV COMPONENT, or AV VIDEO does not appear correctly.• IsthesettingforBNCorD-SUBofINPUTSELECTonthe

OPTION menu correct? (See page 26.)• Istheinputsignalcompatiblewiththismonitor?(Seepage55.)

Control buttons do not work.There is no picture.• Loadnoisesfromoutsidemaybeinterferingwithnormal

operation. Turn off the power and turn it on after waiting at least5seconds,andthenchecktheoperation.

The input mode changes automatically.• WhentheAUTOINPUTCHANGEisONandnosignal

is present in a selected input mode, the AUTO INPUT CHANGEautomaticallychangestheselectedmodetoamode where a video signal is present.

The input mode may change in the following cases:-Whenacomputerisinstandbymode.-Whenvideoplayisstoppedwithaplaybackdevice.

The touch panel does not respond.• IstheUSBcableconnectedproperly?(TouchPanelDriver

Operation Manual)• Hasthetouchpaneldriverbeeninstalled?(TouchPanelDriverOperationManual)

• Hasthepentipofthetouchpenbecomeworn?Replacethepentip.(Seepage20.)

• Isthebatteryinsertedinthewrongorientation(+,-)inthetouchpen?(Seepage18.)

• Isthetouchpenbatteryexhausted?

The response of the touch screen is slow.Some parts of the screen do not respond.• Isthescreenexposedtodirectsunlightorotherstrong

light? The touch panel uses infrared rays and thus may not operate correctly.

• Isthereanobstaclebetweentheinfraredtransmitter/receiverandthetouchpenoryourfinger?Anobstaclewillpreventcorrectoperation.Ifyourfingersorasleeveare too close to the screen, correct operation will not be possible.

• Istheinfraredtransmitter/receiverdirty?Gentlywipeoffany dirt with a soft cloth.

• Ifthetouchpanelistouchedwithasmalltiplessthanabout3/16inch(4mm)x3/16inch(4mm),thetouchmaynotbe detected by infrared and correct operation will not take place.

• WhenstartingyourcomputerorconnectingtheUSBcable,do not touch the touch panel. If you touch the touch panel, this may be detected as an element failure in the infrared transmitter/receiver and incorrect operation will result.

Power LED flashes red.“STATUS [xxxx]” appears in the corner of the screen.• Hardwarehasaproblem.TurnoffthemonitorandrequestrepairfromyourSHARPdealer. (WhenSTATUSALERTissettoOSD&LED.Thisvariesdepending on the setting.)

The touch panel power LED lights red.• Hardwarehasaproblem.TurnoffthemonitorandrequestrepairfromyourSHARPdealer.

52E

When “AUTO DIMMING” is displayed.• Whentheinternaltemperatureofthemonitorrises

excessively, the brightness of the backlight automatically decreases in order to prevent a further temperature rise. If you attempt to use toadjustthebrightnesswhilethemonitorisinthisstate,“AUTODIMMING”isdisplayedand you cannot change the brightness.

• Removethecauseoftheexcessivetemperaturerise.

The monitor makes a cracking sound.• Youmayoccasionallyhearacrackingsoundfromthe

monitor. This happens when the cabinet slightly expands and contracts according to change in temperature. This does not affect the monitor’s performance.

The Power LED is flashing in red and green alternately. When “TEMPERATURE” is displayed in the corner of the screen.• Whentheinternaltemperatureofthemonitorrises

excessively, the brightness of the backlight decreases automaticallyinordertopreventhigh-temperature-relatedproblems.Whenthisoccurs,“TEMPERATURE”isdisplayedonthescreenandthePowerLEDflashesredandgreenalternately.(WhenTEMPERATUREALERTissettoOSD&LED.Thisvariesdependingonthesetting.)

• Iftheinternaltemperaturerisesfurther,themonitorautomaticallyentersstandbymode.(ThePowerLEDcontinuesflashingredandgreenalternately.)

• Removethecauseoftheexcessivetemperaturerise.-Ifthemonitorentersstandbymodeduetoarisein

temperature, to return to normal display, turn the power switch off and then back on again. The monitor, however, will enter standby mode again if the cause of the temperature rise is not eliminated. (See page 8.)

-Checkwhetherthemonitorisplacedatalocationwhereaquickriseintemperatureislikely.Internaltemperaturerisesquicklyiftheventsonthemonitorareblocked.

-Internaltemperaturerisesquicklyifdustaccumulatesinside the monitor or around the vents. Remove dust if possible.AskSHARPdealeraboutremovinginternaldust.

Troubleshooting

53 E

Specifications nProduct SpecificationsModel PN-L602BLCD component 60" Class [60-1/16 inch (152.5cm) diagonal] TFT LCDMax. resolution (pixels) 1920 x 1080Max. colors Approx. 1.06 billion colorsPixel pitch 0.692 mm (H) × 0.692 mm (V)Viewing angle 160° right/left/up/down (contrast ratio ≥ 10)Screen active area inch (mm) 52-5/16 x 29-7/16 (1329.1 x 747.6)Computer input signal Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 Ω]Sync signal Horizontal/vertical separate (TTL: positive/negative), Sync-on-green,

Composite sync (TTL: positive/negative)Video color system NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAMPlug and play VESA DDC2BPower management VESA DPMS, DVI DMPMInput terminals PC/AV Digital HDMI x 1

PC Analog Mini D-sub 15 pin, 3 rows x 1Audio 3.5 mm mini stereo jack x 1Serial (RS-232C) D-sub 9 pin x 1

When PN-ZB01 (optional) is attached

PC/AV Digital DVI-D 24 pin (HDCP compatible) x 1PC Analog BNC *1*2 x 1AV Composite video BNC x 1

S-video x 1Component BNC (Y, Cb/Pb, Cr/Pr) *1 x 1

Audio RCA pin (L/R) x 2Output terminals Audio RCA pin (L/R) x 1

Serial (RS-232C) D-sub 9 pin x 1When PN-ZB01 (optional) is attached

PC/AV Digital DVI-D 24 pin x 1External speaker 7 W + 7 W [6 Ω]

LAN terminal [When PN-ZB01 (optional) is attached]

10 BASE-T/100 BASE-TX

Speaker output 7 W + 7 WTouch Panel Detection method Infrared blocking detection method

Detection area inch (mm) 52-5/16 x 29-7/16 (1329.1 x 747.6)PC connector USB (1.1 compliant)Power supply Supplied from USBTouch pen Ultrasonic communication method

Power requirement AC 100 V - 240 V, 2.0 A, 50/60 HzOperating temperature *3*4 41°F to 95°F (5°C to 35°C)Operating humidity*4 20% to 80% (no condensation)Power consumption(Maximum / input signal waiting mode *5 / standby mode *6)

165 W / 1.0 W / 1.0 W

Power consumption[When PN-ZB01 (optional) is attached]

170 W

Dimensions (excluding protrusions) inch (mm) Approx. 56-11/16 (W) x 4 (D) x 33-11/16 (H) (1,440 x 101 x 855)Weight lbs. (kg) Approx. 119.0 (54)Weight [PN-ZB01 (optional)] lbs. (kg) Approx. 1.102 (0.5)

*1 Cannot be used simultaneously.*2 Does not support plug and play.*3 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP.

In such cases, please check the temperature condition specified by the optional equipments.*4 In addition, check the requirements of the computer and other devices to be connected, and make sure that all requirements are satisfied.*5 When AUTO INPUT CHANGE is set to OFF. *6 When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 WAs a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

54E

Specifications

nDimensional DrawingsNote that the values shown are approximate values.

51-1/8 [1298]

56-11/16 [1440]

Ope

ning

hei

ght (

30-1

/2 [7

74])

Opening width (53-7/16 [1358])

1-7/8 [47]

33-1

1/16

[855

]

2-3/16 [56]

3-1/16[77.5]

4 [101]

34-7

/8 [8

86]

36 [9

14]

VESA holes *

3-15/16 [100]

3-15/16[100]

7-7/8 [200]

7-7/8 [200]

7-7

/8 [2

00]

Unit: inch [mm]

When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method. SHARP recommends using M6 screws and tighten the screws. Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch (8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times or more the weight of the monitor.

nPower managementThis monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in order for the monitor’s power management function to work.

DPMS: Display Power Management Signaling

DPMS Screen Power consumption Hsync Vsync

ON STATE Display 165 W*1 Yes YesSTANDBY

Nodisplay 1.0 W*1*2

No YesSUSPEND Yes NoOFF STATE No No

*1 When PN-ZB01 (optional) is not connected.*2 When AUTO INPUT CHANGE is set to OFF.

DMPM: Digital Monitor Power Management

DMPM Screen Power consumption

Monitor ON Display 165 W*1

Active OFF No display 1.0 W*1*2

nDDC (plug and play)The monitor supports the VESA DDC (Display Data Channel) standard.DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters is exchanged between the two. This function can be used if the computer supports DDC and it has been configured to detect plug-and-play monitors.There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.

55 E

nCompatible signal timing (PC)

VESA

Wide

US TEXTSun

Screen resolution Hsync Vsync Dot frequency Digital

640 × 480

800 × 600

848 × 4801024 × 768

1152 × 8641280 × 768

1280 × 8001280 × 960

1280 × 1024

1360 × 7681400 × 10501440 × 900

1600 × 1200*1

1680 × 10501920 × 1200*1

1280 × 7201920 × 1080

720 × 4001024 × 768

1152 × 900

1280 × 1024

1600 × 1000

31.5kHz37.9kHz37.5kHz35.1kHz37.9kHz48.1kHz46.9kHz31.0kHz48.4kHz56.5kHz60.0kHz67.5kHz47.8kHz60.3kHz49.7kHz60.0kHz64.0kHz80.0kHz47.7kHz65.3kHz55.9kHz75.0kHz65.3kHz74.0kHz44.7kHz66.3kHz67.5kHz31.5kHz48.3kHz53.6kHz56.6kHz61.8kHz71.8kHz71.7kHz81.1kHz68.6kHz

60Hz72Hz75Hz56Hz60Hz72Hz75Hz60Hz60Hz70Hz75Hz75Hz60Hz75Hz60Hz60Hz60Hz75Hz60Hz60Hz60Hz60Hz60Hz60Hz60Hz60Hz60Hz70Hz60Hz66Hz70Hz66Hz

76.2Hz67.2Hz76Hz66Hz

25.175MHz31.5MHz31.5MHz36.0MHz40.0MHz50.0MHz49.5MHz

33.75MHz65.0MHz75.0MHz

78.75MHz108.0MHz79.5MHz

102.25MHz83.5MHz

108.0MHz108.0MHz135.0MHz85.5MHz

121.75MHz106.5MHz162.0MHz

146.25MHz154.0MHz74.4MHz

148.5MHz148.5MHz28.3MHz

64.13MHz70.4MHz

74.25MHz94.88MHz

108.23MHz117.01MHz134.99MHz135.76MHz

YesYesYes

-YesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYes

--------

Analog(D-SUB/RGB*2)

YesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYesYes

DVI*2 HDMIYesYesYes

-YesYesYes

-YesYesYesYes

--

YesYesYesYesYesYes

-YesYesYesYesYesYesYes

--------

*1 Displays a reduced image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed. *2 Available when the PN-ZB01 (optional) is attached.

* Allarecompliantonlywithnon-interlaced.* DependingontheconnectedPC,imagesmaynotbedisplayedproperlyevenifthecompatiblesignaldescribedaboveisinput.* ThefrequencyvaluesfortheSunarereferencevalues.

nCompatible signal timing (AV)Screen resolution Frequency DVI-D* HDMI Component

1920×1080p 24Hz - Yes -50Hz Yes Yes Yes

59.94Hz Yes Yes Yes60Hz Yes Yes Yes

1920×1080i 50Hz Yes Yes Yes59.94Hz Yes Yes Yes60Hz Yes Yes Yes

1280×720p 50Hz Yes Yes Yes59.94Hz Yes Yes Yes60Hz Yes Yes Yes

720×576p 50Hz Yes Yes Yes720×480p 59.94Hz Yes Yes Yes

60Hz Yes Yes Yes640×480p(VGA) 59.94Hz Yes Yes -

60Hz Yes Yes -720(1440)×576i 50Hz - Yes Yes720(1440)×480i 59.94Hz - Yes Yes

60Hz - Yes Yes

*AvailablewhenthePN-ZB01(optional)isattached.

Specifications

56E

Specifications

nPC/AV DVI-D input terminal pins(DVI-D 24 pin)

No. Function No. Function1 TMDSdata2- 13 N.C.2 TMDSdata2+ 14 +5V3 TMDSdata2/4shield 15 GND4 N.C. 16 Hot-plugdetection5 N.C. 17 TMDSdata0-6 DDCclock 18 TMDSdata0+7 DDCdata 19 TMDSdata0/5shield8 N.C. 20 N.C.9 TMDSdata1- 21 N.C.10 TMDSdata1+ 22 TMDSclockshield11 TMDSdata1/3shield 23 TMDSclock+12 N.C. 24 TMDSclock-

nPC D-sub input terminal pins(Mini D-sub 15 pin)

No. Function No. Function1 Red video signal input 9 +5V2 Greenvideosignalinput 10 GND3 Bluevideosignalinput 11 N.C.4 N.C. 12 DDCdata5 GND 13 Hsyncsignalinput6 GNDforredvideosignal 14 Vsyncsignalinput7 GNDforgreenvideosignal 15 DDCclock8 GNDforbluevideosignal

nPC/AV DVI-D output terminal pins(DVI-D 24 pin)

No. Function No. Function1 TMDSdata2- 13 N.C.2 TMDSdata2+ 14 +5V3 TMDSdata2/4shield 15 GND4 N.C. 16 Hot-plugdetection5 N.C. 17 TMDSdata0-6 DDCclock 18 TMDSdata0+7 DDCdata 19 TMDSdata0/5shield8 N.C. 20 N.C.9 TMDSdata1- 21 N.C.10 TMDSdata1+ 22 TMDSclockshield11 TMDSdata1/3shield 23 TMDSclock+12 N.C. 24 TMDSclock-

nPC/AV HDMI input terminal pins(HDMITM Connector)

No. Function No. Function1 TMDSdata2+ 11 TMDSclockshield2 TMDSdata2shield 12 TMDSclock-3 TMDSdata2- 13 CEC4 TMDSdata1+ 14 N.C.5 TMDSdata1shield 15 SCL6 TMDSdata1- 16 SDA7 TMDSdata0+ 17 DDC/CECGND8 TMDSdata0shield 18 +5V9 TMDSdata0- 19 Hot-plugdetection10 TMDSclock+

nRS-232C input terminal pins(D-sub 9 pin)

No. Function No. Function1 N.C. 6 N.C.2 Transmitted data 7 N.C.3 Received data 8 N.C.4 N.C. 9 N.C.5 GND

nRS-232C output terminal pins(D-sub 9 pin)

No. Function No. Function1 N.C. 6 N.C.2 Received data 7 N.C.3 Transmitted data 8 N.C.4 N.C. 9 N.C.5 GND

57 E

• Wheninstalling,removingormovingthemonitor,ensurethatthisiscarriedoutbyatleast2people.• Besuretouseawall-mountbracketdesignedordesignatedformountingthemonitor.• Thismonitorisdesignedtobeinstalledonaconcretewallorpillar.Reinforcedworkmightbenecessaryforsomematerials

such as plaster / thin plastic board / wood before starting installation. This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor. Install by the most suitable method for the material and the structure.

• ToattachaVESA-compliantmountingbracket,useM6screwsthatare5/16inch(8mm)to3/8inch(10mm)longerthanthethickness of the mounting bracket.

• Aftermounting,pleasecarefullyensurethemonitorissecure,andnotabletocomeloosefromthewallormount.• DonotuseanyscrewholesotherthanVESAholesforinstallation.

Mounting Precautions (For SHARP dealers and service engineers)

nAttaching the Tray1. Remove the cover from the back of the monitor.

2. Secure the tray mounting fitting.Secureusingthescrewremovedinstep1and2M5traymounting screws (supplied).

(3)(2)

(1)

M5 tray mounting screws(supplied)

Tray mountingfitting

Screw removed in step 1

Cover (supplied)

Bracket (supplied)

3. Secure the tray.Insertthetrayintothetraymountingfittingandsecurewith2 M4 tray mounting screws (supplied).

Tray(supplied)

M4 tray mounting screws(supplied)

PN-L602BMuEN11K(1)