Platform EPCM-505C User Guide - Intel® Software · Intel Cup Embedded System Design Contest...
Transcript of Platform EPCM-505C User Guide - Intel® Software · Intel Cup Embedded System Design Contest...
Platform EPCM-505C
User Guide
Guangzhou Zhiyuan Electronics Stock Co., LTD
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
I
Safety information
Electrical safety
To prevent electrical shock hazard, disconnect the power cable from the electrical outlet
before relocation the system
When adding or removing devices to or from the system, ensure that the power cables for
the device are unplugged before the signal cables are connected. If possible, disconnect all
power and signal cables from the system before you add or remove device.
Before connecting or removing signal cables form the platform, ensure that all power cables
are unplugged.
Seek professional assistance before using an adapter or extension card. These devices could
interrupt the grounding circuit.
Ensure that your power supply is set to the correct voltage in your area. If you are not sure
about the voltage of the electrical outlet you are using, contact your local power company.
If the power supply is broken, do not try to fix it by yourself. Please contact us.
Operating safety
Before installing the platform and adding devices on it, carefully read the manuals that came
with the package.
Before using the product, ensure all cables are correctly connected and the power cables are
not damaged. If you detect any damage, contact us immediately.
To avoid short circuits, keep paper clips, screws, and staples away from the platform.
Avoid dust, humidity, and temperature extremes. Do not place the product in any area
where it may become wet.
Place the product on a stable surface.
If you encounter technical problems with the platform, please contact us.
Users MUST not remove the heat skin and cooler fan. Remove the heat skin or cooler fan
may cause ICs over heat damage.
Don’t touch the heat skin. The temperature of the heat skin may rise to 55 Centigrade/131
Fahrenheit.
Contact Information
Name: Wangyi Li
Email: [email protected]
Phone: 0086 20 2826 7916 (9:00~17:00 Beijing Time)
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
II
About this guide
This user guide contains the information you need when installing and configuring the platform.
Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
DANGER/WARNING:
Information to prevent injury to yourself when you trying to complete a tack.
Caution: Information to prevent damage to the components when you trying to
complete a task.
IMPORTANT:
Instructions you MUST follow to complete a task.
NOTICE:
Tips and additional information help you complete a task.
Typography
Bold text Indicates a menu or an item to select
Italics Used to emphasize a word or a phrase
<Key> Key enclosed in a pair of angle brackets means that you must press
the enclosed key.
<Key1> + <Key2> + <Key3> If you must press two or more keys simultaneously, the keys are
linked with a plus sign (+).
Example: <Ctrl> + <Alt> + <Del>
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
III
Platform Specifications
Processor
Intel® Atom™ E645C processor
1.0 GHz single core with Intel® Hyper-Threading Technology
Intergraded Altera FPGA
Memory
1 GByte DDR2-800 on board memory
IOH
Intel® EG20T
Storage
1 SATA 1.5Gbps port by Intel® EG20T
1 onboard CF card slot, support CF card type II
PCIE
1 Mini PCIE slot onboard
Connectors
Back Panel I/O
1 12V DC power supply port
2 serial ports, 1 support RS232/RS485
1 microphone input jack
1 line out jack
1 video input
1 CAN 2.0B port
1 12Bit ADC port
1 8Bit ADC port
1 12bit DAC port
4 USB 2.0 high speed ports
1 VGA port
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
IV
1 Ethernet by EG20T, supports IEEE1588
1 Ethernet by FPGA
Onboard connectors
1 Low Pin Count (LPC) interface
1 I2C interface
1 SPI interface
1 Camera interface
1 Serial port config pin
1 Alter FPGA JTAG
1 H.D.D power supply
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
1
Capter 1 Product information
1.1 Package contents
Check your platform package for the following items.
EPCM-505C Platform User guide 1 x FPGA adapter
1 x RS232 cable(Female to
female)
1 x RS232 cable(Male to
female)
1 x Peripheral connector to
SATA cable
1 x Peripheral connector
conversion cable 1 x Ethernet cable 1 x Terasic® USB balter
1 x LA1016 logic analyzer 1 x power supply module
If any of the above items damaged or missing, contact us.
The illustrated items above are for reference only. Actual product specification
may vary with different modules.
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
2
Capter 2 Hardware information
2.1 Before you proceed
Take note of the following precautions before you install platform or change any platform
settings.
Unplug the power cord from the wall socket before touching any components.
Before handling components, use a grounded wrist strap or touch a safely
grounded object or a metal object, such as the power supply case, to avoid
damaging them due to static electricity.
Hold the components by the edges to avoid touching the ICs on them.
Whenever you uninstall any components, place it on a grounded antistatic pad
or in the bag that came with the components.
Before you install or remove any components, ensure that power cord is
unplugged from the power supply.
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
3
2.2 Platform overview
2.2.1 Platform layout
The platform consists of 5 parts.
No. Description
1 LCD screen & touch screen assembly
2 Base board
3 CPU core board
4 Heat skin
5 Cooler fan
Users MUST not remove the heat skin and cooler fan. Remove the heat skin or
cooler fan may cause ICs over heat damage.
Don’t touch the heat skin. The temperature of the heat skin may rise to 55
Centigrade/131 Fahrenheit.
Users may remove the LCD screen module, if it is not needed.
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
4
2.2.2 Base board layout
No. Description
1 Altera® HSMC connector
2 FPGA Button
3 Camera Interface
4 FPGA LEDs
5 LPC(Low pin count)
6 Serial ATA connector
7 Peripheral connector
8 I2C interface
9 SPI interface
10 Ethernet 2(FPGA)
11 Ethernet 1(EG20T)
12 VGA connector
13 USB 2.0 1/2/3/4
14 12 Bit ADC
15 8 Bit ADC
16 10 Bit DAC
17 Mini PCI-e
18 CMOS lithium cell battery
19 Power LED
20 H.D.D. LED
21 Buzzer
22 CAN 2.0B interface
23 Audio line out
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
5
No. Description
24 LCD & touch screen assembly connector
25 Audio microphone input
26 Video input
27 Serial port2
28 Serial port1
29 Power input connector
30 PWR_ON button
31 RST button
2.2.3 CPU core board layout
No. Description
1 Intel® IOH EG20T
2 FPGA config device Altera® EPCS64
3 Altera® FPGA JTAG pin header
4 Intel® Atom™ E546C processor
5 DDR2-800 Memory chips
6 DDR2 Memory chip connected to FPGA
7 NOR flash connected to FPGA
8 XDP port(not available)
9 SF100 port(not available)
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
6
2.2.4 Onboard header pins
FPGA JTAG pins
Pin No. Signal Pin No. Signal
1 TCK 2 GND
3 TDO 4 VCC 3.3V
5 TMS 6 VCC 3.3V
7 N/C 8 N/C
9 TDI 10 GND
LPC (Low Pin Count) Pins
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
7
Pin No. Signal Pin No. Signal
1 VCC 3.3V 2 FRAME_N
3 AD3 4 AD2
5 AD1 6 AD0
7 GND 8 PLTRST
9 CLKOUT0 10 SERIRQ
I2C Pins
Pin No. Signal Pin No. Signal
1 VCC 3.3V 2 N/C
3 N/C 4 SCLK
5 N/C 6 SDATA
7 GND 8 N/C
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
8
SPI Pins
Pin No. Signal Pin No. Signal
1 VCC 3.3V 2 VCC 3.3V
3 SCK 4 MISO
5 SSN 6 MOSI
7 GND 8 GND
Camera Pins
Pin No. Signal Pin No. Signal
1 SCLK 2 SDA
3 CLK 4 DATA7
5 DATA6 6 DATA5
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
9
7 DATA4 8 DATA3
9 DATA2 10 DATA1
11 DATA0 12 GND
2.2.5 Onboard button
PWR_ON button
Press the PWR_ON button after you connect the power cable, the platform will start to POST.
RST button
Press the RST button the system will restart to POST after the platform is powered on.
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
10
FPGA button
There are four buttons connected to the FPGA I/O pins.
Switch FPGA I/O pin
SW3 7A_TIO5_LVDS_TX_T12_DP_M
SW4 7A_TIO5_LVDS_RD_T11_DP_M
SW5 7A_TIO4_LVDS_TX_T13_DP_P
SW6 7A_TIO5_LVDS_RD_T11_DP_P
2.2.6 Onboard LEDs
PWR LED
This red LED indicates the power status after the platform is powered on.
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
11
H.D.D LED
This green LED indicates the STAT device and CF card status.
FPGA LEDs
There are eight green LEDs connected to the FPGA I/O pins.
LEDs PCB mark FPGA I/O Pin
D19 7A_TIO5_LVDS_TX_T10_DP_M
D20 7A_TIO4_LVDS_RD_T13_DP_M
D21 7A_TIO5_LVDS_TX_T11_DP_P
D22 7A_TIO4_LVDS_RD_T13_DP_P
D23 7A_TIO5_LVDS_TX_T11_DP_M
D24 7A_TIO5_LVDS_RD_T12_DP_M
D25 7A_TIO5_LVDS_TX_T12_DP_P
D26 7A_TIO5_LVDS_RD_T12_DP_P
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
12
LAN port LED indications
Activity Link LED Speed LED
Status Description Status Description
OFF No Link OFF 10 Mbps connection
Orange Linked Orange 100 Mbps connection
Blinking Data Activity Green 1 Gbps connection
The Ethernet by FPGA do not recommend using. This Ethernet has bug with
performance.
2.2.7 How to remove LCD screen
If user does not need to use the LCD screen, user can remove it.
1. Ensure the power cable is unplugged.
2. Loosen the four screws that fixed LCD module.
3. Remove the LCD screen module from the base board.
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
13
Capter 3 Building your system
1. Connect SATA power cables to the SATA H.D.D.
2. Connect SATA cable.
3. Connect USB keyboard and mouse.
4. Connect power supply cable to power connector.
5. Press PWR ON button on the right edge of the board. The development platform will start to
boot.
6. Board will start to POST.
7. If it is not connected with storage device, the platform will stop on the EFI shell. Show as.
Figure 1
8. If connected storage device with OS, input exit command in the EFI shell, platform will start
to load OS.
Intel Cup Embedded System Design Contest Platform EPCM-505C User Guide
14
Capter 4 Other Information
4.1 Where to find Information
Intel cup electronic design contest web site: http://nuedc.sjtu.edu.cn/
More information for Intel® embedded: http://edc.intel.com
4.2 Technical Support
Technical support email: [email protected]
Technical support phone: 0086 20 2826 7916(9:00~17:00 Beijing Time, Mon ~ Fri)
Technical support forum: http://bbs.zlgmcu.com
Technical support forum:
Http://software.intel.com/en-us/forums/intel-cup-embedded-system-design-contest/
Intel cup electronic design contest Tencent® QQ group: No.127018145