Plain Cylindrical Adaptor – vibration-damped A3000 · 2020. 4. 28. · A 1 102 ISO turning Walter...
Transcript of Plain Cylindrical Adaptor – vibration-damped A3000 · 2020. 4. 28. · A 1 102 ISO turning Walter...
A 1
101
ISO turning
Walter Turn turning tools – Internal machining
ToolDesignation
d1
inch d11
l4
inch
l5
inch
l1
inch d13lbs
Parallel shank
l4
d1
l5
l1
d11
d13
A3000.20-Q32-165 1,250 Q32 6,500 5,000 11,713 G 1/4 3,97
A3000.20-Q32-229 1,250 Q32 9,000 5,000 14,213 G 1/4 5,07
A3000.24-Q40-203 1,500 Q40 8,000 6,000 14,252 G 1/4 7,72
A3000.24-Q40-279 1,500 Q40 11,000 6,000 17,252 G 1/4 9,48
A3000.32-Q50-267 2,000 Q50 10,500 8,000 18,791 G 1/4 16,76
A3000.32-Q50-368 2,000 Q50 14,496 8,000 22,791 G 1/4 20,28
l4
d1
l5
l1
d11
d13 A3000.24-Q40-356 1,500 Q40 14,000 6,000 20,252 G 1/4 11,46
A3000.32-Q50-470 2,000 Q50 18,500 8,000 26,791 G 1/4 24,69
QuadFit exchangeable heads − see the “Turning” section
Bodies and assembly parts are included in the scope of delivery.
Accure·tec
A3000
Plain Cylindrical Adaptor – vibration-damped
– For QuadFit exchangeable heads
– With preset vibration damping
Assembly partsd11 Q32 Q40 Q50
Hook wrench
Tightening torque
SD9000-Q32
25 Nm
SD9000-Q40
35 Nm
SD9000-Q50
55 Nm
Accessoriesd11 Q32 Q40 Q50
Torque wrench with hook
Tightening torque
SD4000-Q32-25
25 Nm
SD4000-Q40-35
35 Nm
SD4000-Q50-55
55 Nm
Hook for torque wrench SD6000-Q32 SD6000-Q40 SD6000-Q50
A 1
102
ISO turning
Walter Turn turning tools – Internal machining
a b c / New addition to the product range
ToolDesignation d1 d11
d12
mm
l4
mm
l16
mm
l17
mm nmax
Walter CaptoTM in acc. with ISO 26623
l4
l16
d11 d1
l17
d12
A3000-C6-Q32-160 C6 Q32 32 160 129 135 10000 1,8
A3000-C6-Q32-224 C6 Q32 32 224 193 199 8000 2,1
A3000-C6-Q32-288 C6 Q32 32 288 257 263 6000 2,6
A3000-C6-Q40-208 C6 Q40 40 208 177 183 8000 2,9
A3000-C6-Q40-288 C6 Q40 40 288 257 263 6000 3,7
A3000-C6-Q40-368 C6 Q40 40 368 337 343 5000 4,5
A3000-C6-Q50-268 C6 Q50 50 268 238 243 6000 5
A3000-C6-Q50-368 C6 Q50 50 368 338 343 4000 6,6
A3000-C6-Q50-468 C6 Q50 50 468 438 443 2500 8,5
A3000-C8-Q32-224 C8 Q32 32 224 181 191 8000 3,2
A3000-C8-Q32-288 C8 Q32 32 288 245 255 6000 3,6
A3000-C8-Q40-288 C8 Q40 40 288 245 255 6000 4,7
A3000-C8-Q40-368 C8 Q40 40 368 325 335 5000 5,6
A3000-C8-Q50-268 C8 Q50 50 268 225 235 6000 5,9
A3000-C8-Q50-368 C8 Q50 50 368 325 335 4000 7,5
A3000-C8-Q50-468 C8 Q50 50 468 425 435 2500 9,4
QuadFit exchangeable heads − see the “Turning” section
Bodies and assembly parts are included in the scope of delivery.
Accure·tec
A3000-C
Walter CaptoTM adaptor – vibration-damped
– For QuadFit exchangeable heads
– With preset vibration damping
Assembly partsd11 Q32 Q40 Q50
Hook wrench
Tightening torque
SD9000-Q32
25 Nm
SD9000-Q40
35 Nm
SD9000-Q50
55 Nm
Accessoriesd11 Q32 Q40 Q50
Torque wrench with hook
Tightening torque
SD4000-Q32-25
25 Nm
SD4000-Q40-35
35 Nm
SD4000-Q50-55
55 Nm
Hook for torque wrench SD6000-Q32 SD6000-Q40 SD6000-Q50
A 1
103
ISO turning
Walter Turn turning tools – Internal machining
ToolDesignation
d1
mm d11
d12
mm
l4
mm
l16
mm
l17
mm nmax
HSK-T DIN 69893-7
l4
l16
d1
l17
d11
d12
A3000-H100T-Q32-224 100 Q32 32 224 189 195 8000 3,4
A3000-H100T-Q32-288 100 Q32 32 288 253 259 6000 3,8
A3000-H100T-Q40-288 100 Q40 40 288 253 259 6000 4,9
A3000-H100T-Q40-368 100 Q40 40 368 333 339 5000 5,8
A3000-H100T-Q50-268 100 Q50 50 268 234 239 6000 6,2
A3000-H100T-Q50-368 100 Q50 50 368 334 339 4000 7,8
A3000-H100T-Q50-468 100 Q50 50 468 434 439 25000 9,7
QuadFit exchangeable heads − see the “Turning” section
Bodies and assembly parts are included in the scope of delivery.
Accure·tec
A3000-HSK-T
HSK-T adaptor – vibration-damped
– For QuadFit exchangeable heads
– With preset vibration damping
Assembly partsd11 Q32 Q40 Q50
Hook wrench
Tightening torque
SD9000-Q32
25 Nm
SD9000-Q40
35 Nm
SD9000-Q50
55 Nm
Accessoriesd11 Q32 Q40 Q50
Torque wrench with hook
Tightening torque
SD4000-Q32-25
25 Nm
SD4000-Q40-35
35 Nm
SD4000-Q50-55
55 Nm
Hook for torque wrench SD6000-Q32 SD6000-Q40 SD6000-Q50
A 1
104
ISO turning
Walter Turn turning tools – Internal machining
a b c / New addition to the product range
ToolDesignation d1
Dmin
mm
f
mm
l4
mm γ λs Type
λs
f
l4
d1
95°
Dmin
Q32-DCLNR/L-22032-12 12 Q32 40 22 32 -6° -10°
CN .. 1204 ..Q40-DCLNR/L-27032-12 12 Q40 50 27 32 -6° -10°
Q50-DCLNR/L-32032-12 12 Q50 63 32 32 -6° -8°
Q50-DCLNR/L-32037-16 16 Q50 63 32 37 -5° -14° CN .. 1606 ..
Measured with master insert: CN .. 120408 / CN .. 160612
For information on the rake angle γ (for indexable inserts without chip groove) and on the inclination angle λs, see “Technical information – ISO turning”
Ordering example, right-hand tool: Q32-DCLNR-22032-12/ordering example, left-hand tool: Q32-DCLNL-22032-12
Bodies and assembly parts are included in the scope of delivery.
Walter Turn
Q...-DCLN
Exchangeable head – Rigid clamping
– QuadFit
95°
CN . . CN . .
Assembly partsType CN .. 1204 .. CN .. 1606 ..
Shim AP354-CN12 AP302-CN16
Screw for shim
Tightening torque
FS1461 (Torx 15IP)
2,5 Nm
FS1463 (Torx 20IP)
5,0 Nm
Clamp PK241 PK242
Clamp screw
Tightening torque
FS1473 (Torx 15IP)
3,9 Nm
FS1474 (Torx 20IP)
6,4 Nm
Pressure spring FS1470 FS1471
Pin RS117 RS117
Torx key FS1465 (Torx 15IP /SW 3,5) FS1464 (Torx 20IP)
AccessoriesType CN .. 1204 .. CN .. 1606 ..
Clamp set
(standard assembly parts)PK241-SET PK242-SET
Carbide clamp set
Insert with drilled holePK245-SET PK246-SET
Carbide clamp set
Insert without drilled holePK254-SET
A 1
105
ISO turning
Walter Turn turning tools – Internal machining
a b c / New addition to the product range
ToolDesignation d1
Dmin
mm
f
mm
l4
mm γ λs Type
λs
f
l4
d1
93°
Dmin
Q32-DDUNR/L-22032-15 15 Q32 40 21,9 32 -6° -14°
DN .. 1506 ..Q40-DDUNR/L-27032-15 15 Q40 50 27 32 -6° -12°
Q50-DDUNR/L-32032-15 15 Q50 63 32 32 -6° -12°
Measured with master insert: DN .. 150608
For information on the rake angle γ (for indexable inserts without chip groove) and on the inclination angle λs, see “Technical information – ISO turning”
Ordering example, right-hand tool: Q32-DDUNR-22032-15/ordering example, left-hand tool: Q32-DDUNL-22032-15
Bodies and assembly parts are included in the scope of delivery.
Walter Turn
Q...-DDUN
Exchangeable head – Rigid clamping
– QuadFit
93°
≤ 30° DN . . DN . .
Assembly partsType DN .. 1506 ..
Shim AP304-DN15
Screw for shim
Tightening torque
FS1461 (Torx 15IP)
2,5 Nm
Clamp PK241
Clamp screw
Tightening torque
FS1473 (Torx 15IP)
3,9 Nm
Pressure spring FS1470
Pin RS117
Torx key FS1465 (Torx 15IP /SW 3,5)
AccessoriesType DN .. 1506 ..
Carbide clamp set
Insert with drilled holePK245-SET
Clamp set
(standard assembly parts)PK241-SET
Carbide clamp set
Insert without drilled holePK254-SET
Shim for DN .. 1504 .. AP304-DN1504
A 1
106
ISO turning
Walter Turn turning tools – Internal machining
a b c / New addition to the product range
ToolDesignation d1
Dmin
mm
f
mm
l4
mm γ λs Type
λs
f
l4
d1
95°
Dmin
Q32-DWLNR/L-22035-08 8 Q32 40 22 35 -5° -14°
WN .. 0804 ..Q40-DWLNR/L-27037-08 8 Q40 50 27 37 -5° -12°
Q50-DWLNR/L-32038-08 8 Q50 63 32 38 -5° -12°
Measured with master insert: WN .. 080408
For information on the rake angle γ (for indexable inserts without chip groove) and on the inclination angle λs, see “Technical information – ISO turning”
Ordering example, right-hand tool: Q32-DWLNR-22035-08/ordering example, left-hand tool: Q32-DWLNL-22035-08
Bodies and assembly parts are included in the scope of delivery.
Walter Turn
Q...-DWLN
Exchangeable head – Rigid clamping
– QuadFit
95°
WN . . WN . .
Assembly partsType WN .. 0804 ..
Shim AP331-WN08
Screw for shim
Tightening torque
FS1461 (Torx 15IP)
2,5 Nm
Clamp PK241
Clamp screw
Tightening torque
FS1473 (Torx 15IP)
3,9 Nm
Pressure spring FS1470
Pin RS117
Torx key FS1465 (Torx 15IP /SW 3,5)
AccessoriesType WN .. 0804 ..
Clamp set
(standard assembly parts)PK241-SET
Carbide clamp set
Insert with drilled holePK245-SET
Carbide clamp set
Insert without drilled holePK254-SET
A 1
107
ISO turning
Walter Turn turning tools – Internal machining
a b c / New addition to the product range
ToolDesignation d1
Dmin
mm
f
mm
l4
mm γ λs Type
Dmin
λs
d1
l4
95°f
Q32-SCLCR/L-22032-09 9 Q32 40 22 32 0° -2°
CC .. 09T3 ..Q40-SCLCR/L-27032-09 9 Q40 50 27 32 0° -2°
Q50-SCLCR/L-32032-09 9 Q50 63 32 32 0° -2°
Q32-SCLCR/L-22032-12 12 Q32 40 22 32 0° -8°
CC .. 1204 ..Q40-SCLCR/L-27032-12 12 Q40 50 27 32 0° -8°
Q50-SCLCR/L-32032-12 12 Q50 63 32 32 0° -9°
Measured with master insert: CC.. 09T308 / CC .. 120408
For information on the rake angle γ (for indexable inserts without chip groove) and on the inclination angle λs, see “Technical information – ISO turning”
Ordering example, right-hand tool: Q32-SCLCR-22032-09/ordering example, left-hand tool: Q32-SCLCL-22032-09
Bodies and assembly parts are included in the scope of delivery.
Walter Turn
Q...-SCLC
Exchangeable head – Screw clamping
– QuadFit
95°
7°
CC . .
Assembly partsType CC .. 09T3 .. CC .. 1204 ..
Clamping screw for indexable insert
Tightening torque
FS2062 (Torx 15IP)
3,0 Nm
FS2281 (Torx 20IP)
5,0 Nm
Shim AP364-CC1208
Screw for shim FS2592 (SW 5)
Torx key FS1465 (Torx 15IP /SW 3,5)
Allen key FS1464 (Torx 20IP)
Allen key for shim ISO2936-5 (SW 5)
A 1
108
ISO turning
Walter Turn turning tools – Internal machining
ToolDesignation d1
Dmin
mm
f
mm
l4
mm γ λs Type
Dmin
d1
l4
93°f
λs
Q32-SDUCR/L-22032-11 11 Q32 40 22 32 0° -5°
DC .. 11T3 ..Q40-SDUCR/L-27032-11 11 Q40 50 27 32 0° -5°
Q50-SDUCR/L-32032-11 11 Q50 63 32 32 0° -5°
Measured with master insert: DC .. 11T308
For information on the rake angle γ (for indexable inserts without chip groove) and on the inclination angle λs, see “Technical information – ISO turning”
Ordering example, right-hand tool: Q32-SDUCR-22032-11/ordering example, left-hand tool: Q32-SDUCL-22032-11
Bodies and assembly parts are included in the scope of delivery.
Walter Turn
Q...-SDUC
Exchangeable head – Screw clamping
– QuadFit
93°
≤ 30°
7°
DC . .
Assembly partsType DC .. 11T3 ..
Clamping screw for indexable insert
Tightening torque
FS1461 (Torx 15IP)
2,5 Nm
Torx key FS1465 (Torx 15IP /SW 3,5)
A 1
109
ISO turning
Walter Turn turning tools – Internal machining
a b c / New addition to the product range
ToolDesignation d1
Dmin
mm
f
mm
l4
mm
l20
mm
X1
mm γ λs Type
d1
l4
X1
Dmin
λs
93°
l20
f
Q32-SDUCR/L-22018-11X 11 Q32 40 21,9 18 37,5 5,9 0° -5°
DC .. 11T3 ..Q40-SDUCR/L-27017-11X 11 Q40 50 26,9 17 40,5 6,9 0° -5°
Q50-SDUCR/L-32017-11X 11 Q50 63 32 17 42,5 6,9 0° -5°
Measured with master insert: DC .. 11T308
For information on the rake angle γ (for indexable inserts without chip groove) and on the inclination angle λs, see “Technical information – ISO turning”
Ordering example, right-hand tool: Q32-SDUCR-22018-11X/ordering example, left-hand tool: Q32-SDUCL-22018-11X
Bodies and assembly parts are included in the scope of delivery.
Walter Turn
Q...-SDUC...-X
Exchangeable head – Screw clamping
– QuadFit
≤ 30°
7°
DC . .
Assembly partsType DC .. 11T3 ..
Clamping screw for indexable insert
Tightening torque
FS1461 (Torx 15IP)
2,5 Nm
Torx key FS1465 (Torx 15IP /SW 3,5)
A 1
110
ISO turning
Walter Turn turning tools – Internal machining
ToolDesignation d1
Dmin
mm
f
mm
l4
mm
l20
mm
X1
mm γ λs Type
λs
d1
62°30´
Dmin
X1
l20
l4
f
Q32-SDXCR/L-22025-11 11 Q32 40 21,9 25 37,5 5,9 0° -5°
DC .. 11T3 ..Q40-SDXCR/L-27025-11 11 Q40 50 26,9 25 40,5 6,9 0° -5°
Q50-SDXCR/L-32025-11 11 Q50 63 31,9 25 42,5 6,9 0° -5°
Measured with master insert: DC .. 11T308
For information on the rake angle γ (for indexable inserts without chip groove) and on the inclination angle λs, see “Technical information – ISO turning”
Ordering example, right-hand tool: Q32-SDXCR-22025-11/ordering example, left-hand tool: Q32-SDXCL-22025-11
Bodies and assembly parts are included in the scope of delivery.
Walter Turn
Q...-SDXC
Exchangeable head – Screw clamping
– For QuadFit exchangeable heads
≤ 60°
62°30'
7°
DC . .
Assembly partsType DC .. 11T3 ..
Clamping screw for indexable insert
Tightening torque
FS1461 (Torx 15IP)
2,5 Nm
Torx key FS1465 (Torx 15IP /SW 3,5)
A 1
111
ISO turning
Walter Turn turning tools – Internal machining
a b c / New addition to the product range
ToolDesignation d1
Dmin
mm
f
mm
l4
mm γ λs Type
λs
l4
f
91°
Dmin
d1
Q32-STFCR/L-22032-16 16 Q32 40 22 32 0° -10°
TC .. 16T3 ..Q40-STFCR/L-27032-16 16 Q40 50 27 32 0° -8°
Q50-STFCR/L-32032-16 16 Q50 63 32 32 0° -8°
Measured with master insert: TC .. 16T308
For information on the rake angle γ (for indexable inserts without chip groove) and on the inclination angle λs, see “Technical information – ISO turning”
Ordering example, right-hand tool: Q32-STFCR-22032-16/ordering example, left-hand tool: Q32-STFCL-22032-16
Bodies and assembly parts are included in the scope of delivery.
Walter Turn
Q...-STFC
Exchangeable head – Screw clamping
– QuadFit
91°7°
TC . .
Assembly partsType TC .. 16T3 ..
Clamping screw for indexable insert
Tightening torque
FS2063 (Torx 15IP)
3,0 Nm
Shim
for radius
AP317-TC1612
r ≤ 1,2 mm
Screw for shim FS2068 (SW 3,5)
Torx key FS1465 (Torx 15IP /SW 3,5)
A 1
112
ISO turning
Walter Turn turning tools – Internal machining
ToolDesignation d1
Dmin
mm
f
mm
l4
mm γ λs Type
λs
l4
f
Dmin
93°
d1
Q32-SVUBR/L-22032-16 16 Q32 40 22 32 0° -3°VB .. 1604 ..
VC .. 1604 ..Q40-SVUBR/L-27032-16 16 Q40 50 26,9 32 0° -3°
Q50-SVUBR/L-32032-16 16 Q50 63 31,9 32 0° -3°
Measured with master insert: VB .. 160408
For information on the rake angle γ (for indexable inserts without chip groove) and on the inclination angle λs, see “Technical information – ISO turning”
Ordering example, right-hand tool: Q32-SVUBR-22032-16/ordering example, left-hand tool: Q32-SVUBL-22032-16
Bodies and assembly parts are included in the scope of delivery.
Walter Turn
Q...-SVUB
Exchangeable head – Screw clamping
– QuadFit
93°
≤ 50°
5°
VB . .
Assembly partsType
VB .. 1604 ..
VC .. 1604 ..
Clamping screw for indexable insert
Tightening torque
FS2063 (Torx 15IP)
3,0 Nm
Shim
for radius
AP316-VB1608
r ≤ 0,8 mm
Screw for shim FS2068 (SW 3,5)
Torx key FS1465 (Torx 15IP /SW 3,5)