PLA polyester modular enclosuresPolyester enclosures completely closed IP65 (EN 60529) PLA 12123...
Transcript of PLA polyester modular enclosuresPolyester enclosures completely closed IP65 (EN 60529) PLA 12123...
1 2 3 4 5 6 7
10 814 13 12 11 9
3/68
5 Detail of fixing the glass to the inside of the door.
1 Wall fixing brackets.
PLA polyester modular enclosures
8 Detail of bosses on the doors, back and lower part of the enclosure for fixing of various materials.
12 Mounting plate fixing support, adjustable every 25 mm.
03_068_069.indd 6803_068_069.indd 68 22/2/08 18:35:3022/2/08 18:35:30
3/69
7 The locking system is outside the sealed area, which guarantees the IP over time. Handle lock with detail of the cover that hides the lock device.
6 Ribbed door to make fixing of posters difficult. Likewise, this uneven surface makes the door thicker and also improves the robustness of the enclosure.
4 Detail of 120º hinge with easily removable stainless steel safety pin. Seal that guarantees IP65 watertightness.
3 The enclosures with canopies allow self-ventilation of the enclosure, preventing condensation and maintaining the IP54.
2 2-point locking system (up to 750 mm height) or 4-point locking system (from 1,000 mm height).
11 Door retainer.
14 Metal, insulating or universal mounting plates to be fixed directly to the back of the enclosure or by using adjustable supports.
10 Door opening to 180º, which improves accessibility to the interior of the enclosure with plinth and canopy. The plinth-type base allows direct floor fixing.
9 Anti-vandalism reinforcement.
13 PLAZ... enclosures with open plinth-type bottom for easy cable entry.
03_068_069.indd 6903_068_069.indd 69 22/2/08 18:35:3222/2/08 18:35:32
3/70
CONSTRUCTION SYSTEMS
PLA 1054 PLA 1054 T PLAZ 1054 PLAZ 1054 T
PLA 1054 KT PLA 1054 TKT PLAZ 1054 KT PLAZ 1054 TKT
PLA 1054 R PLA 1054 TR PLAZ 1054 R PLAZ 1054 TR
PLA 1054 P PLA 1054 TP PLAZ 1054 P PLAZ 1054 TP
PLA 1054 PKT PLA 1054 TPKT PLAZ 1054 PKT PLAZ 1054 TPKT
PLA 1273 PR PLA 1273 TPR PLAZ 1273 PR PLAZ 1273 TPR
Plain doorPLA/PLAZ...
Transparent doorPLA/PLAZ...KT
Ribbed doorPLA/PLAZ...R
Plain front andback doorsPLA/PLAZ...P
Transparent front door andplain back doorPLA/PLAZ...PKT
Ribbed front and back doorsPLA/PLAZ...PR
Closed topSelf-ventilated top with
canopy
Enclosures with open plinth-type baseEnclosures with closed baseTable of formation references
General table with the construction systems on the horizontal axis and the various versions of doors on the vertical axis, offering apanoramic view of the formation of all the possibilities of references.
Closed topSelf-ventilated top with
canopy
PLA... PLA...T PLAZ... PLAZ...T
120° 120°
IP65
Door opening
Degree of protection IP54
120°
IP54
180°
IP54
EXAMPLES OF FORMING REFERENCES
Height: 1,000 Width: 500 Depth: 420
Top and bottom closed, with transparent door.
Ref.: PLA 1054 KT
Height: 1,200 Width: 750 Depth: 320
Self-ventilated top with canopy, open plinth-type bottom, ribbed front and back doors.
Ref.: PLA Z 1273 TPR
With base
Construction systems
Dimensions (mm)
Closed Open, plinth-type Height Width DepthExamples of enclosures
PLA -
- PLAZ XX XX X
PLA - 10 5 4
- PLAZ 12 7 3
03_070_083_EN.indd 7003_070_083_EN.indd 70 5/3/08 11:20:505/3/08 11:20:50
3/71
The table showing each of the dimensions (height, width and depth) determines the digits to use when forming the references.The tables in grey and blue have to do with to the examples of the reference formation table.
Height Width Depth
Nominal dimensions (mm)
5 00
5 00
7 50 3 20
7 50
10 00
10 00
12 50 4 20
12 50
15 00
Door versionWith top
ClosedSelf-ventilatedwith canopy Plain Transparent Ribbed Plain front cover and back Ribbed front cover and back
- T - KT R P PR
- - - KT - - -
- T - - - - PR
03_070_083_EN.indd 7103_070_083_EN.indd 71 5/3/08 11:20:525/3/08 11:20:52
3/72
Construction specifications
c Resistance to the main chemical agents and corrosive environments.
c Stabilised against UV rays.
c Door reversibility with opening to 120º, with max. admissible load of 30 kg/m2.
c Lock outside of the sealed area, with a 2-point locking system up to 750 mm height, 4-point locking system from 1000 mm height.
c Interior of the enclosure equipped with bosses for M8 inserts. They allow direct fixing of mounting plates and/or the desired installation system, accessories, etc.
Technical specifications
c Conforms to general rules for empty enclosures established in IEC and EN 62208.
c IP65 conforming to IEC 60529 (EN 60529).
c High resistance to mechanical impacts IK10 (20J) conforming to IEC and EN 62262).
c Self-extinguishing, conforming to IEC 60695-2-1 (960°).
c Extreme operating temperatures from –50 to +150 ºC.
c Suitable for double insulation profiles conforming to IEC 60439-1 (EN 60439-1).
c Resistant to corrosion.
PLA 1253
PLA . . . Polyester enclosures completely closedIP65 (EN 60529)
PLA 12123
Hot-press moulded fibreglass-reinforced polyester enclosures, in grey RAL-7032 (able to withstand weather conditions).
03_070_083_EN.indd 7203_070_083_EN.indd 72 5/3/08 11:20:535/3/08 11:20:53
3/73
PLA. . . Completely closed polyester enclosuresIP65 (EN 60529)
Basic composition
c Enclosure with top and base completely closed.
c Sealing gasket.
c Plain, transparent or ribbed door.
c KT model: transparent door of tempered glass with a high resistance to mechanical impacts IK08 (5J) conforming to EN 62262.
c ..R model: ribbed door to make fixing of posters difficult and with “anti-lever” hinges.
c Back panel or door.
c Reversible door with 2 hinges up to 750 mm height, and 4 from 1000 mm height.
c Standard double bar lock, operated by key LDB5.
c Two-door enclosures have a central profile.
SELECTION TABLE FOR CLOSED POLYESTER ENCLOSURES
Height Width Depth No. of doors
Nominal dimensions (mm)
500 500 320 1 PLA 553 PLA 553 R PLA 553 KT PLA 553 P PLA 553 PR PLA 553 PKT
420 1 PLA 554 PLA 554 R PLA 554 KT PLA 554 P PLA 554 PR PLA 554 PKT
750 320 1 PLA 573 PLA 573 R PLA 573 KT PLA 573 P PLA 573 PR PLA 573 PKT
420 1 PLA 574 PLA 574 R PLA 574 KT PLA 574 P PLA 574 PR PLA 574 PKT
1000 320 2 PLA 5103 PLA 5103 R PLA 5103 KT PLA 5103 P PLA 5103 PR PLA 5103 PKT
420 2 PLA 5104 PLA 5104 R PLA 5104 KT PLA 5104 P PLA 5104 PR PLA 5104 PKT
1250 320 2 PLA 5123 PLA 5123 R PLA 5123 KT PLA 5123 P PLA 5123 PR PLA 5123 PKT
420 2 PLA 5124 PLA 5124 R PLA 5124 KT PLA 5124 P PLA 5124 PR PLA 5124 PKT
750 500 320 1 PLA 753 PLA 753 R PLA 753 KT PLA 753 P PLA 753 PR PLA 753 PKT
420 1 PLA 754 PLA 754 R PLA 754 KT PLA 754 P PLA 754 PR PLA 754 PKT
750 320 1 PLA 773 PLA 773 R PLA 773 KT PLA 773 P PLA 773 PR PLA 773 PKT
420 1 PLA 774 PLA 774 R PLA 774 KT PLA 774 P PLA 774 PR PLA 774 PKT
1000 320 2 PLA 7103 PLA 7103 R PLA 7103 KT PLA 7103 P PLA 7103 PR PLA 7103 PKT
420 2 PLA 7104 PLA 7104 R PLA 7104 KT PLA 7104 P PLA 7104 PR PLA 7104 PKT
1250 320 2 PLA 7123 PLA 7123 R PLA 7123 KT PLA 7123 P PLA 7123 PR PLA 7123 PKT
420 2 PLA 7124 PLA 7124 R PLA 7124 KT PLA 7124 P PLA 7124 PR PLA 7124 PKT
1000 500 320 1 PLA 1053 PLA 1053 R PLA 1053 KT PLA 1053 P PLA 1053 PR PLA 1053 PKT
420 1 PLA 1054 PLA 1054 R PLA 1054 KT PLA 1054 P PLA 1054 PR PLA 1054 PKT
750 320 1 PLA 1073 PLA 1073 R PLA 1073 KT PLA 1073 P PLA 1073 PR PLA 1073 PKT
420 1 PLA 1074 PLA 1074 R PLA 1074 KT PLA 1074 P PLA 1074 PR PLA 1074 PKT
1000 320 2 PLA 10103 PLA 10103 R PLA 10103 KT PLA 10103 P PLA 10103 PR PLA 10103 PKT
420 2 PLA 10104 PLA 10104 R PLA 10104 KT PLA 10104 P PLA 10104 PR PLA 10104 PKT
1250 320 2 PLA 10123 PLA 10123 R PLA 10123 KT PLA 10123 P PLA 10123 PR PLA 10123 PKT
420 2 PLA 10124 PLA 10124 R PLA 10124 KT PLA 10124 P PLA 10124 PR PLA 10124 PKT
1250 500 320 1 PLA 1253 PLA 1253 R PLA 1253 KT PLA 1253 P PLA 1253 PR PLA 1253 PKT
420 1 PLA 1254 PLA 1254 R PLA 1254 KT PLA 1254 P PLA 1254 PR PLA 1254 PKT
750 320 1 PLA 1273 PLA 1273 R PLA 1273 KT PLA 1273 P PLA 1273 PR PLA 1273 PKT
420 1 PLA 1274 PLA 1274 R PLA 1274 KT PLA 1274 P PLA 1274 PR PLA 1274 PKT
1000 320 2 PLA 12103 PLA 12103 R PLA 12103 KT PLA 12103 P PLA 12103 PR PLA 12103 PKT
420 2 PLA 12104 PLA 12104 R PLA 12104 KT PLA 12104 P PLA 12104 PR PLA 12104 PKT
1250 320 2 PLA 12123 PLA 12123 R PLA 12123 KT PLA 12123 P PLA 12123 PR PLA 12123 PKT
420 2 PLA 12124 PLA 12124 R PLA 12124 KT PLA 12124 P PLA 12124 PR PLA 12124 PKT
1500 500 320 1 PLA 1553 PLA 1553 R PLA 1553 KT PLA 1553 P PLA 1553 PR PLA 1553 PKT
420 1 PLA 1554 PLA 1554 R PLA 1554 KT PLA 1554 P PLA 1554 PR PLA 1554 PKT
750 320 1 PLA 1573 PLA 1573 R PLA 1573 KT PLA 1573 P PLA 1573 PR PLA 1573 PKT
420 1 PLA 1574 PLA 1574 R PLA 1574 KT PLA 1574 P PLA 1574 PR PLA 1574 PKT
1000 320 2 PLA 15103 PLA 15103 R PLA 15103 KT PLA 15103 P PLA 15103 PR PLA 15103 PKT
420 2 PLA 15104 PLA 15104 R PLA 15104 KT PLA 15104 P PLA 15104 PR PLA 15104 PKT
1250 320 2 PLA 15123 PLA 15123 R PLA 15123 KT PLA 15123 P PLA 15123 PR PLA 15123 PKT
420 2 PLA 15124 PLA 15124 R PLA 15124 KT PLA 15124 P PLA 15124 PR PLA 15124 PKT
03_070_083_EN.indd 7303_070_083_EN.indd 73 5/3/08 11:20:555/3/08 11:20:55
3/74
Construction specifications
c Resistance to the main chemical agents and corrosive environments.
c Stabilised against UV rays.
c Door reversibility with opening to 120º, with max. admissible load of 30 kg/m2.
c Lock outside of the sealed area, with a 2-point locking system up to 750 mm height, 4-point locking system from 1000 mm height.
c Interior of the enclosure equipped with bosses for M8 inserts. They allow direct fixing of mounting plates and/or the desired installation system, accessories, etc.
Technical specifications
c Conforms to general rules for empty enclosures established in IEC and EN 62208.
c IP54 conforming to IEC 60529 (EN 60529).
c High resistance to mechanical impacts IK10 (20J) conforming to IEC and EN 62262.
c Self-extinguishing, conforming to IEC 60695-2-1 (960°).
c Extreme operating temperatures from –50 to +150 ºC.
c Suitable for double insulation profiles conforming to IEC 60439-1 (EN 60439-1).
c Resistant to corrosion.
PLA. . .TPolyester enclosures with self-ventilated top with canopy and closed baseIP54 (EN 60529)
Hot-press moulded, fibreglass-reinforced, self-ventilated polyester enclosures, in grey RAL-7032 (able to withstand weather conditions).
PLA 1253T
03_070_083_EN.indd 7403_070_083_EN.indd 74 5/3/08 11:20:565/3/08 11:20:56
3/75
PLA. . .TPolyester enclosures with self-ventilated top with canopy and closed baseIP54 (EN 60529)
SELECTION TABLE FOR CLOSED BASE, SELF-VENTILATED POLYESTER ENCLOSURES
Height Width Depth No. of doors
Nominal dimensions (mm)
500 500 320 1 PLA 553 T PLA 553 TR PLA 553 TKT PLA 553 TP PLA 553 TPR PLA 553 TPKT
420 1 PLA 554 T PLA 554 TR PLA 554 TKT PLA 554 TP PLA 554 TPR PLA 554 TPKT
750 320 1 PLA 573 T PLA 573 TR PLA 573 TKT PLA 573 TP PLA 573 TPR PLA 573 TPKT
420 1 PLA 574 T PLA 574 TR PLA 574 TKT PLA 574 TP PLA 574 TPR PLA 574 TPKT
1000 320 2 PLA 5103 T PLA 5103 TR PLA 5103 TKT PLA 5103 TP PLA 5103 TPR PLA 5103 TPKT
420 2 PLA 5104 T PLA 5104 TR PLA 5104 TKT PLA 5104 TP PLA 5104 TPR PLA 5104 TPKT
1250 320 2 PLA 5123 T PLA 5123 TR PLA 5123 TKT PLA 5123 TP PLA 5123 TPR PLA 5123 TPKT
420 2 PLA 5124 T PLA 5124 TR PLA 5124 TKT PLA 5124 TP PLA 5124 TPR PLA 5124 TPKT
750 500 320 1 PLA 753 T PLA 753 TR PLA 753 TKT PLA 753 TP PLA 753 TPR PLA 753 TPKT
420 1 PLA 754 T PLA 754 TR PLA 754 TKT PLA 754 TP PLA 754 TPR PLA 754 TPKT
750 320 1 PLA 773 T PLA 773 TR PLA 773 TKT PLA 773 TP PLA 773 TPR PLA 773 TPKT
420 1 PLA 774 T PLA 774 TR PLA 774 TKT PLA 774 TP PLA 774 TPR PLA 774 TPKT
1000 320 2 PLA 7103 T PLA 7103 TR PLA 7103 TKT PLA 7103 TP PLA 7103 TPR PLA 7103 TPKT
420 2 PLA 7104 T PLA 7104 TR PLA 7104 TKT PLA 7104 TP PLA 7104 TPR PLA 7104 TPKT
1250 320 2 PLA 7123 T PLA 7123 TR PLA 7123 TKT PLA 7123 TP PLA 7123 TPR PLA 7123 TPKT
420 2 PLA 7124 T PLA 7124 TR PLA 7124 TKT PLA 7124 TP PLA 7124 TPR PLA 7124 TPKT
1000 500 320 1 PLA 1053 T PLA 1053 TR PLA 1053 TKT PLA 1053 TP PLA 1053 TPR PLA 1053 TPKT
420 1 PLA 1054 T PLA 1054 TR PLA 1054 TKT PLA 1054 TP PLA 1054 TPR PLA 1054 TPKT
750 320 1 PLA 1073 T PLA 1073 TR PLA 1073 TKT PLA 1073 TP PLA 1073 TPR PLA 1073 TPKT
420 1 PLA 1074 T PLA 1074 TR PLA 1074 TKT PLA 1074 TP PLA 1074 TPR PLA 1074 TPKT
1000 320 2 PLA 10103 T PLA 10103 TR PLA 10103 TKT PLA 10103 TP PLA 10103 TPR PLA 10103 TPKT
420 2 PLA 10104 T PLA 10104 TR PLA 10104 TKT PLA 10104 TP PLA 10104 TPR PLA 10104 TPKT
1250 320 2 PLA 10123 T PLA 10123 TR PLA 10123 TKT PLA 10123 TP PLA 10123 TPR PLA 10123 TPKT
420 2 PLA 10124 T PLA 10124 TR PLA 10124 TKT PLA 10124 TP PLA 10124 TPR PLA 10124 TPKT
1250 500 320 1 PLA 1253 T PLA 1253 TR PLA 1253 TKT PLA 1253 TP PLA 1253 TPR PLA 1253 TPKT
420 1 PLA 1254 T PLA 1254 TR PLA 1254 TKT PLA 1254 TP PLA 1254 TPR PLA 1254 TPKT
750 320 1 PLA 1273 T PLA 1273 TR PLA 1273 TKT PLA 1273 TP PLA 1273 TPR PLA 1273 TPKT
420 1 PLA 1274 T PLA 1274 TR PLA 1274 TKT PLA 1274 TP PLA 1274 TPR PLA 1274 TPKT
1000 320 2 PLA 12103 T PLA 12103 TR PLA 12103 TKT PLA 12103 TP PLA 12103 TPR PLA 12103 TPKT
420 2 PLA 12104 T PLA 12104 TR PLA 12104 TKT PLA 12104 TP PLA 12104 TPR PLA 12104 TPKT
1250 320 2 PLA 12123 T PLA 12123 TR PLA 12123 TKT PLA 12123 TP PLA 12123 TPR PLA 12123 TPKT
420 2 PLA 12124 T PLA 12124 TR PLA 12124 TKT PLA 12124 TP PLA 12124 TPR PLA 12124 TPKT
1500 500 320 1 PLA 1553 T PLA 1553 TR PLA 1553 TKT PLA 1553 TP PLA 1553 TPR PLA 1553 TPKT
420 1 PLA 1554 T PLA 1554 TR PLA 1554 TKT PLA 1554 TP PLA 1554 TPR PLA 1554 TPKT
750 320 1 PLA 1573 T PLA 1573 TR PLA 1573 TKT PLA 1573 TP PLA 1573 TPR PLA 1573 TPKT
420 1 PLA 1574 T PLA 1574 TR PLA 1574 TKT PLA 1574 TP PLA 1574 TPR PLA 1574 TPKT
1000 320 2 PLA 15103 T PLA 15103 TR PLA 15103 TKT PLA 15103 TP PLA 15103 TPR PLA 15103 TPKT
420 2 PLA 15104 T PLA 15104 TR PLA 15104 TKT PLA 15104 TP PLA 15104 TPR PLA 15104 TPKT
1250 320 2 PLA 15123 T PLA 15123 TR PLA 15123 TKT PLA 15123 TP PLA 15123 TPR PLA 15123 TPKT
420 2 PLA 15124 T PLA 15124 TR PLA 15124 TKT PLA 15124 TP PLA 15124 TPR PLA 15124 TPKT
Basic composition
c Open top with canopy.
c Base completely closed.
c Sealing gasket.
c Plain, transparent or ribbed door.
c KT model: transparent door of tempered glass with a high resistance to mechanical impacts IK08 (5J) conforming to IEC and EN 62262.
c ..R model: ribbed door to make fixing of posters difficult and with “anti-lever” hinges.
c Back panel or door.
c Reversible door with 2 hinges up to 750 mm height, and 4 from 1000 mm height.
c Standard double bar handle lock, operated by key LDB5.
c Two-door enclosures have a central profile.
03_070_083_EN.indd 7503_070_083_EN.indd 75 5/3/08 11:20:575/3/08 11:20:57
3/76
Construction specifications
c Resistance to the main chemical agents and corrosive environments.
c Stabilised against UV rays.
c Door reversibility with opening to 120º, with max. admissible load of 30 kg/m2.
c Lock outside of the sealed area, with a 2-point locking system up to 750 mm height, 4-point locking system from 1000 mm height.
c Interior of the enclosure equipped with bosses for M8 inserts. They allow direct fixing of mounting plates and/or the desired installation system, accessories, etc.
Technical specifications
c Conforms to general rules for empty enclosures established in IEC and EN 62208.
c IP54 conforming to IEC 60529 (EN 60529).
c High resistance to mechanical impacts IK10 (20J) conforming to IEC and EN 62262.
c Self-extinguishing, conforming to IEC 60695-2-1 (960°).
c Extreme operating temperatures from –50 to +150 ºC.
c Suitable for double insulation profiles conforming to IEC 60439-1 (EN 60439-1).
c Resistant to corrosion.
PLAZ. . .Polyester enclosures with closed top and open plinth-type baseIP54 (EN 60529)
PLAZ 1253
Hot-press moulded fibreglass-reinforced polyester enclosures, in grey RAL-7032 (able to withstand weather conditions).
03_070_083_EN.indd 7603_070_083_EN.indd 76 5/3/08 11:20:575/3/08 11:20:57
3/77
PLAZ. . .Polyester enclosures with closed top and open plinth-type baseIP54 (EN 60529)
Basic composition
c Closed top.
c Open plinth-type base.
c Sealing gasket.
c Plain, transparent or ribbed door.
c KT model: transparent door of tempered glass with a high resistance to mechanical impacts IK08 (5J) conforming to IEC and EN 62262.
c ..R model: ribbed door to make fixing of posters difficult and with “anti-lever” hinges.
c Back panel or door.
c Reversible door with 2 hinges up to 750 mm height, and 4 from 1000 mm height.
c Standard double bar handle lock, operated by key LDB5.
c Two-door enclosures have a central profile.
SELECTION TABLE FOR POLYESTER ENCLOSURES WITH CLOSED TOP AND OPEN PLINTH-TYPE BASE
Height Width Depth No. of doors
Nominal dimensions (mm)
500 500 320 1 PLAZ 553 PLAZ 553 R PLAZ 553 KT PLAZ 553 P PLAZ 553 PR PLAZ 553 PKT
420 1 PLAZ 554 PLAZ 554 R PLAZ 554 KT PLAZ 554 P PLAZ 554 PR PLAZ 554 PKT
750 320 1 PLAZ 573 PLAZ 573 R PLAZ 573 KT PLAZ 573 P PLAZ 573 PR PLAZ 573 PKT
420 1 PLAZ 574 PLAZ 574 R PLAZ 574 KT PLAZ 574 P PLAZ 574 PR PLAZ 574 PKT
1000 320 2 PLAZ 5103 PLAZ 5103 R PLAZ 5103 KT PLAZ 5103 P PLAZ 5103 PR PLAZ 5103 PKT
420 2 PLAZ 5104 PLAZ 5104 R PLAZ 5104 KT PLAZ 5104 P PLAZ 5104 PR PLAZ 5104 PKT
1250 320 2 PLAZ 5123 PLAZ 5123 R PLAZ 5123 KT PLAZ 5123 P PLAZ 5123 PR PLAZ 5123 PKT
420 2 PLAZ 5124 PLAZ 5124 R PLAZ 5124 KT PLAZ 5124 P PLAZ 5124 PR PLAZ 5124 PKT
750 500 320 1 PLAZ 753 PLAZ 753 R PLAZ 753 KT PLAZ 753 P PLAZ 753 PR PLAZ 753 PKT
420 1 PLAZ 754 PLAZ 754 R PLAZ 754 KT PLAZ 754 P PLAZ 754 PR PLAZ 754 PKT
750 320 1 PLAZ 773 PLAZ 773 R PLAZ 773 KT PLAZ 773 P PLAZ 773 PR PLAZ 773 PKT
420 1 PLAZ 774 PLAZ 774 R PLAZ 774 KT PLAZ 774 P PLAZ 774 PR PLAZ 774 PKT
1000 320 2 PLAZ 7103 PLAZ 7103 R PLAZ 7103 KT PLAZ 7103 P PLAZ 7103 PR PLAZ 7103 PKT
420 2 PLAZ 7104 PLAZ 7104 R PLAZ 7104 KT PLAZ 7104 P PLAZ 7104 PR PLAZ 7104 PKT
1250 320 2 PLAZ 7123 PLAZ 7123 R PLAZ 7123 KT PLAZ 7123 P PLAZ 7123 PR PLAZ 7123 PKT
420 2 PLAZ 7124 PLAZ 7124 R PLAZ 7124 KT PLAZ 7124 P PLAZ 7124 PR PLAZ 7124 PKT
1000 500 320 1 PLAZ 1053 PLAZ 1053 R PLAZ 1053 KT PLAZ 1053 P PLAZ 1053 PR PLAZ 1053 PKT
420 1 PLAZ 1054 PLAZ 1054 R PLAZ 1054 KT PLAZ 1054 P PLAZ 1054 PR PLAZ 1054 PKT
750 320 1 PLAZ 1073 PLAZ 1073 R PLAZ 1073 KT PLAZ 1073 P PLAZ 1073 PR PLAZ 1073 PKT
420 1 PLAZ 1074 PLAZ 1074 R PLAZ 1074 KT PLAZ 1074 P PLAZ 1074 PR PLAZ 1074 PKT
1000 320 2 PLAZ 10103 PLAZ 10103 R PLAZ 10103 KT PLAZ 10103 P PLAZ 10103 PR PLAZ 10103 PKT
420 2 PLAZ 10104 PLAZ 10104 R PLAZ 10104 KT PLAZ 10104 P PLAZ 10104 PR PLAZ 10104 PKT
1250 320 2 PLAZ 10123 PLAZ 10123 R PLAZ 10123 KT PLAZ 10123 P PLAZ 10123 PR PLAZ 10123 PKT
420 2 PLAZ 10124 PLAZ 10124 R PLAZ 10124 KT PLAZ 10124 P PLAZ 10124 PR PLAZ 10124 PKT
1250 500 320 1 PLAZ 1253 PLAZ 1253 R PLAZ 1253 KT PLAZ 1253 P PLAZ 1253 PR PLAZ 1253 PKT
420 1 PLAZ 1254 PLAZ 1254 R PLAZ 1254 KT PLAZ 1254 P PLAZ 1254 PR PLAZ 1254 PKT
750 320 1 PLAZ 1273 PLAZ 1273 R PLAZ 1273 KT PLAZ 1273 P PLAZ 1273 PR PLAZ 1273 PKT
420 1 PLAZ 1274 PLAZ 1274 R PLAZ 1274 KT PLAZ 1274 P PLAZ 1274 PR PLAZ 1274 PKT
1000 320 2 PLAZ 12103 PLAZ 12103 R PLAZ 12103 KT PLAZ 12103 P PLAZ 12103 PR PLAZ 12103 PKT
420 2 PLAZ 12104 PLAZ 12104 R PLAZ 12104 KT PLAZ 12104 P PLAZ 12104 PR PLAZ 12104 PKT
1250 320 2 PLAZ 12123 PLAZ 12123 R PLAZ 12123 KT PLAZ 12123 P PLAZ 12123 PR PLAZ 12123 PKT
420 2 PLAZ 12124 PLAZ 12124 R PLAZ 12124 KT PLAZ 12124 P PLAZ 12124 PR PLAZ 12124 PKT
1500 500 320 1 PLAZ 1553 PLAZ 1553 R PLAZ 1553 KT PLAZ 1553 P PLAZ 1553 PR PLAZ 1553 PKT
420 1 PLAZ 1554 PLAZ 1554 R PLAZ 1554 KT PLAZ 1554 P PLAZ 1554 PR PLAZ 1554 PKT
750 320 1 PLAZ 1573 PLAZ 1573 R PLAZ 1573 KT PLAZ 1573 P PLAZ 1573 PR PLAZ 1573 PKT
420 1 PLAZ 1574 PLAZ 1574 R PLAZ 1574 KT PLAZ 1574 P PLAZ 1574 PR PLAZ 1574 PKT
1000 320 2 PLAZ 15103 PLAZ 15103 R PLAZ 15103 KT PLAZ 15103 P PLAZ 15103 PR PLAZ 15103 PKT
420 2 PLAZ 15104 PLAZ 15104 R PLAZ 15104 KT PLAZ 15104 P PLAZ 15104 PR PLAZ 15104 PKT
1250 320 2 PLAZ 15123 PLAZ 15123 R PLAZ 15123 KT PLAZ 15123 P PLAZ 15123 PR PLAZ 15123 PKT
420 2 PLAZ 15124 PLAZ 15124 R PLAZ 15124 KT PLAZ 15124 P PLAZ 15124 PR PLAZ 15124 PKT
03_070_083_EN.indd 7703_070_083_EN.indd 77 5/3/08 11:20:585/3/08 11:20:58
3/78
Construction specifications
c Resistance to the main chemical agents and corrosive environments.
c Stabilised against UV rays.
c Door reversibility with opening to 180º, with max. admissible load of 30 kg/m2.
c Lock outside of the sealed area, with a 2-point locking system up to 750 mm height, 4-point locking system from 1000 mm height.
c Interior of the enclosure equipped with bosses for M8 inserts. They allow direct fixing of mounting plates and/or the desired installation system, accessories, etc.
Technical specifications
c Conforms to general rules for empty enclosures established in IEC and EN 62208.
c IP54 conforming to IEC 60529 (EN 60529).
c High resistance to mechanical impacts IK10 (20 J) conforming to IEC and EN 62262.
c Self-extinguishing, conforming to IEC 60695-2-1 (960°).
c Extreme operating temperatures from –50 to +150 ºC.
c Suitable for double insulation profiles conforming to IEC 60439-1 (EN 60439-1).
c Resistant to corrosion.
PLAZ. . .TPolyester enclosures with self-ventilated top with canopy and open plinth-type baseIP54 (EN 60529)
PLAZ 7103T
Hot-press moulded, fibreglass-reinforced, self-ventilated polyester enclosures, in grey RAL-7032 (able to withstand weather conditions).
03_070_083_EN.indd 7803_070_083_EN.indd 78 5/3/08 11:20:595/3/08 11:20:59
3/79
Basic composition
c Open top with canopies.
c Open plinth-type base.
c Sealing gasket.
c Plain, transparent or ribbed door.
c KT model: transparent door of tempered glass with a high resistance to mechanical impacts IK08 (5J) conforming to EN 50102.
c ..R model: ribbed door to make fixing of posters difficult and with “anti-lever” hinges.
c Back panel or door.
c Reversible door with 2 hinges up to 750 mm height, and 4 from 1000 mm height.
c Standard double bar handle lock, operated by key LDB5.
c Two-door enclosures have a central profile.
PLAZ. . .TPolyester enclosures with self-ventilated top with canopy and open plinth-type baseIP54 (EN 60529)
SELECTION TABLE FOR POLYESTER ENCLOSURES WITH SELF-VENTILATED TOP WITH CANOPY AND OPEN PLINTH-TYPE BASE
Height Width Depth No. of doors
Nominal dimensions (mm)
500 500 320 1 PLAZ 553 T PLAZ 553 TR PLAZ 553 TKT PLAZ 553 TP PLAZ 553 TPR PLAZ 553 TPKT
420 1 PLAZ 554 T PLAZ 554 TR PLAZ 554 TKT PLAZ 554 TP PLAZ 554 TPR PLAZ 554 TPKT
750 320 1 PLAZ 573 T PLAZ 573 TR PLAZ 573 TKT PLAZ 573 TP PLAZ 573 TPR PLAZ 573 TPKT
420 1 PLAZ 574 T PLAZ 574 TR PLAZ 574 TKT PLAZ 574 TP PLAZ 574 TPR PLAZ 574 TPKT
1000 320 2 PLAZ 5103 T PLAZ 5103 TR PLAZ 5103 TKT PLAZ 5103 TP PLAZ 5103 TPR PLAZ 5103 TPKT
420 2 PLAZ 5104 T PLAZ 5104 TR PLAZ 5104 TKT PLAZ 5104 TP PLAZ 5104 TPR PLAZ 5104 TPKT
1250 320 2 PLAZ 5123 T PLAZ 5123 TR PLAZ 5123 TKT PLAZ 5123 TP PLAZ 5123 TPR PLAZ 5123 TPKT
420 2 PLAZ 5124 T PLAZ 5124 TR PLAZ 5124 TKT PLAZ 5124 TP PLAZ 5124 TPR PLAZ 5124 TPKT
750 500 320 1 PLAZ 753 T PLAZ 753 TR PLAZ 753 TKT PLAZ 753 TP PLAZ 753 TPR PLAZ 753 TPKT
420 1 PLAZ 754 T PLAZ 754 TR PLAZ 754 TKT PLAZ 754 TP PLAZ 754 TPR PLAZ 754 TPKT
750 320 1 PLAZ 773 T PLAZ 773 TR PLAZ 773 TKT PLAZ 773 TP PLAZ 773 TPR PLAZ 773 TPKT
420 1 PLAZ 774 T PLAZ 774 TR PLAZ 774 TKT PLAZ 774 TP PLAZ 774 TPR PLAZ 774 TPKT
1000 320 2 PLAZ 7103 T PLAZ 7103 TR PLAZ 7103 TKT PLAZ 7103 TP PLAZ 7103 TPR PLAZ 7103 TPKT
420 2 PLAZ 7104 T PLAZ 7104 TR PLAZ 7104 TKT PLAZ 7104 TP PLAZ 7104 TPR PLAZ 7104 TPKT
1250 320 2 PLAZ 7123 T PLAZ 7123 TR PLAZ 7123 TKT PLAZ 7123 TP PLAZ 7123 TPR PLAZ 7123 TPKT
420 2 PLAZ 7124 T PLAZ 7124 TR PLAZ 7124 TKT PLAZ 7124 TP PLAZ 7124 TPR PLAZ 7124 TPKT
1000 500 320 1 PLAZ 1053 T PLAZ 1053 TR PLAZ 1053 TKT PLAZ 1053 TP PLAZ 1053 TPR PLAZ 1053 TPKT
420 1 PLAZ 1054 T PLAZ 1054 TR PLAZ 1054 TKT PLAZ 1054 TP PLAZ 1054 TPR PLAZ 1054 TPKT
750 320 1 PLAZ 1073 T PLAZ 1073 TR PLAZ 1073 TKT PLAZ 1073 TP PLAZ 1073 TPR PLAZ 1073 TPKT
420 1 PLAZ 1074 T PLAZ 1074 TR PLAZ 1074 TKT PLAZ 1074 TP PLAZ 1074 TPR PLAZ 1074 TPKT
1000 320 2 PLAZ 10103 T PLAZ 10103 TR PLAZ 10103 TKT PLAZ 10103 TP PLAZ 10103 TPR PLAZ 10103 TPKT
420 2 PLAZ 10104 T PLAZ 10104 TR PLAZ 10104 TKT PLAZ 10104 TP PLAZ 10104 TPR PLAZ 10104 TPKT
1250 320 2 PLAZ 10123 T PLAZ 10123 TR PLAZ 10123 TKT PLAZ 10123 TP PLAZ 10123 TPR PLAZ 10123 TPKT
420 2 PLAZ 10124 T PLAZ 10124 TR PLAZ 10124 TKT PLAZ 10124 TP PLAZ 10124 TPR PLAZ 10124 TPKT
1250 500 320 1 PLAZ 1253 T PLAZ 1253 TR PLAZ 1253 TKT PLAZ 1253 TP PLAZ 1253 TPR PLAZ 1253 TPKT
420 1 PLAZ 1254 T PLAZ 1254 TR PLAZ 1254 TKT PLAZ 1254 TP PLAZ 1254 TPR PLAZ 1254 TPKT
750 320 1 PLAZ 1273 T PLAZ 1273 TR PLAZ 1273 TKT PLAZ 1273 TP PLAZ 1273 TPR PLAZ 1273 TPKT
420 1 PLAZ 1274 T PLAZ 1274 TR PLAZ 1274 TKT PLAZ 1274 TP PLAZ 1274 TPR PLAZ 1274 TPKT
1000 320 2 PLAZ 12103 T PLAZ 12103 TR PLAZ 12103 TKT PLAZ 12103 TP PLAZ 12103 TPR PLAZ 12103 TPKT
420 2 PLAZ 12104 T PLAZ 12104 TR PLAZ 12104 TKT PLAZ 12104 TP PLAZ 12104 TPR PLAZ 12104 TPKT
1250 320 2 PLAZ 12123 T PLAZ 12123 TR PLAZ 12123 TKT PLAZ 12123 TP PLAZ 12123 TPR PLAZ 12123 TPKT
420 2 PLAZ 12124 T PLAZ 12124 TR PLAZ 12124 TKT PLAZ 12124 TP PLAZ 12124 TPR PLAZ 12124 TPKT
1500 500 320 1 PLAZ 1553 T PLAZ 1553 TR PLAZ 1553 TKT PLAZ 1553 TP PLAZ 1553 TPR PLAZ 1553 TPKT
420 1 PLAZ 1554 T PLAZ 1554 TR PLAZ 1554 TKT PLAZ 1554 TP PLAZ 1554 TPR PLAZ 1554 TPKT
750 320 1 PLAZ 1573 T PLAZ 1573 TR PLAZ 1573 TKT PLAZ 1573 TP PLAZ 1573 TPR PLAZ 1573 TPKT
420 1 PLAZ 1574 T PLAZ 1574 TR PLAZ 1574 TKT PLAZ 1574 TP PLAZ 1574 TPR PLAZ 1574 TPKT
1000 320 2 PLAZ 15103 T PLAZ 15103 TR PLAZ 15103 TKT PLAZ 15103 TP PLAZ 15103 TPR PLAZ 15103 TPKT
420 2 PLAZ 15104 T PLAZ 15104 TR PLAZ 15104 TKT PLAZ 15104 TP PLAZ 15104 TPR PLAZ 15104 TPKT
1250 320 2 PLAZ 15123 T PLAZ 15123 TR PLAZ 15123 TKT PLAZ 15123 TP PLAZ 15123 TPR PLAZ 15123 TPKT
420 2 PLAZ 15124 T PLAZ 15124 TR PLAZ 15124 TKT PLAZ 15124 TP PLAZ 15124 TPR PLAZ 15124 TPKT
03_070_083_EN.indd 7903_070_083_EN.indd 79 5/3/08 11:21:005/3/08 11:21:00
A-1
50
A-1
50
B-150B-150
37.5 75
C-8
25
28.5
C
A260
28.521
25
A-2
55
C-140
C-42
B-95
A-9
5
A-9
5
B-95
1
4
2
1 1
4
2
1
1
C-170
A-2
00
25
A-1
50
B-150
B-120
C-1
25
37.5
C-1
40
B-205
M8
C-13
25
28.5
C
A260
28.521
25
A-2
55
C-140
C-42
B = 500 / 750
17 / 28*
B-95
A-9
5
A-2
53
285/535
A-1
50
B-150
B-120
C-1
25
75
C-1
40
B-205
M840
B =1000/1250
500/750
405 405/655
500
37
A-9
5
B-95A-2
53
285 285/535
1
4
2
3
1
3
1
1
1
4
2
1
3
311
1 1
4 4
1
25
C-170
A-2
00
3/80
FIG. 1
PLA...
FIG. 2
PLA...KT
PLA. . . Polyester enclosures completely closedIP65 (EN 60529)
Dimensions (mm)
03_070_083_EN.indd 8003_070_083_EN.indd 80 5/3/08 11:21:015/3/08 11:21:01
A-1
50
A-1
50
B-150B-150
B-120
C-1
25
B-120C
-125
37.5
B = 500 / 750
C-1
40
B-205
M8
75
C-8
25
28.5
C
A+
38
C-1
40
B-205
M8
B =1000/1250
500 500/750
405 405/655
260
28.5
21
25
A-2
55
C-140
C-42
40
23 / 28* 37
38
B-95
A-9
5
A-9
5
B-954
2
1
4
2
1
1
1
3
4
2
4
3
1
3
3
1
1 1
C-170
A-2
00
25
3/81
FIG. 1
PLA...T
1 Bosses on the back of enclosures starting with 1000 mm wide allow the fixing of partial mounting plates (see plates section). Bosses at the top and bottom are used for fixing depth adjustable supports, internal doors, 19” racks, etc.
In general, all bosses- including those on the sides and on the interior of the door- are prepared for M8 inserts Ref.: TEX 8 for fixing various material.
2 Bosses with M8 inserts equipped with studs for fixing the mounting plates.
3 Centres for floor or plinth fixing.
4 Dimensions of the door opening.
NOTE: in 1250 mm width enclosures, the left door is 500 mm and the right is 750 mm.
PLA. . .TPolyester enclosures with closed top and open plinth-type baseIP54 (EN 60529)
* For mounting plates with reinforcement wing.
Dimensions (mm)
03_070_083_EN.indd 8103_070_083_EN.indd 81 5/3/08 11:21:015/3/08 11:21:01
B-150
A-1
50
A-1
50
37.5
A-1
50
B-150
75
C-42
C-8 260
25
A-2
55
C-140
A+
55
28.5
C
28.521
55
B-95
A-9
5
A-9
5
B-95
1
4
2
1
1
4
2
1
1
33
C-170
A-2
00
25
A-1
50A
-150
B-150
A-9
5
B-95
75
1
4
2
1
B-60
C-1
60
B =1000/1250
500 500/750
405 405/655
C-6
8
B-81
M840
37
6.5 6.5
3
44
3
25
C-42
C-8 260
25
A-2
55
C-140
A+
55
28.5
C
28.521
55
1
C-170
A-2
00
B-150
A-1
50
B-95
A-9
5
37.5
1
4
2
1
B-60
C-1
60
23 / 28*
M8
B = 500/750
C-6
8
B-81
6.5 6.5
3
3
3/82
FIG. 1
PLAZ...
FIG. 2
PLAZ...R
PLAZ. . .Polyester enclosures with self-ventilated top with canopy and closed baseIP54 (EN 60529)
Dimensions (mm)
03_070_083_EN.indd 8203_070_083_EN.indd 82 5/3/08 11:21:015/3/08 11:21:01
B-95
A-9
5
A-9
5
B-95
B-150
A-1
50
37.5
B-60
C-1
60
23 / 28*
M8
B = 500/750
C-6
8
B-81
6.5 6.5
B-60
C-1
60
B =1000/1250
500 500/750
405 405/655
C-6
8
B-81
M840
37
6.5 6.5
A-1
50A
-150
B-150
75
C-42
C-8 260
25
A-2
55
C-140
A+
93
28.5
C
28.521
3855
1
4
2
1
1
4
2
1
1
3
44
3
3
3
C-170
A-2
00
25
3/83
FIG. 1
PLAZ...T
1 Bosses on the back of enclosures starting with 1000 mm wide allow the fixing of partial mounting plates (see plates section). Bosses at the top and bottom are used for fixing depth adjustable supports, internal doors, 19“ racks, etc.
In general, all bosses- including those on the sides and on the interior of the door- are prepared for M8 inserts Ref.: TEX 8 for fixing various material.
2 Bosses with M8 inserts equipped with studs for fixing the mounting plates.
3 Centres for floor or plinth fixing.
4 Dimensions of the door opening.
* For mounting plates with reinforcement wing.
NOTE: in 1250 mm width enclosures, the left door is 500 mm and the right is 750 mm.
PLAZ. . .TPolyester enclosures with self-ventilated top with canopy and open plinth-type baseIP54 (EN 60529)
Dimensions (mm)
03_070_083_EN.indd 8303_070_083_EN.indd 83 5/3/08 11:21:025/3/08 11:21:02
3/84
PLA Composition accessories
PVC frame with sealing gasket that permits lateral coupling of enclosures PLA or PLA...T.
They complement the MUPLA coupling frame for lateral union of enclosures.2 versions: SUPLA for enclosures without canopy and SUPLAT for enclosures with canopy.
Horizontal coupling frame for PLA and PLA...T enclosures
Height (A)
Enclosure dimensions
Depth (C)
Reference
500 320 MUPLA 53
750 320 MUPLA 73
1000 320 MUPLA 103
1250 320 MUPLA 123
1500 320 MUPLA 153
500 420 MUPLA 54
750 420 MUPLA 74
1000 420 MUPLA 104
1250 420 MUPLA 124
1500 420 MUPLA 154
Supplements for coupling PLA and PLA...T enclosures
Depth (C)
Enclosure dimensionsPLA
320 SUPLA 3 SUPLA 3T
420 SUPLA 4 SUPLA 4T
PLA...T
MUPLA...SUPLA...
MUPLA...SUPLA...
03_084_100_EN.indd 8403_084_100_EN.indd 84 2/4/08 12:55:052/4/08 12:55:05
A +
38
C = 320/420
3/85
PLA Composition accessories
Coupling enclosures using an adhesive gasket that guarantees watertightness at the vertical joint of the enclosures PLA.
Ref.: UVPLA.
Application Reference
Adhesive gasket UVPLA
Vertical coupling of enclosures
Made of reinforced pressed polyester, for exterior installation of closed enclosures.
c Colour RAL-7032.
c Self-extinguishable; high resistance to impacts and temperature.
c Excellent resistance to outdoor conditions.
c The nominal height of the enclosure is increased 38 mm.
Canopies
Width (B) Depth (C) No. of doors
ReferenceFor attachment to enclosures
500 320 1 TJPLA 53
750 320 1 TJPLA 73
1000 320 2 TJPLA 103
1250 320 2 TJPLA 123
500 420 1 TJPLA 54
750 420 1 TJPLA 74
1000 420 2 TJPLA 104
1250 420 2 TJPLA 124
03_084_100_EN.indd 8503_084_100_EN.indd 85 2/4/08 12:55:062/4/08 12:55:06
3/86
PLA Composition accessories
B+35
200
B
C
305
C-10
395
To be coupled to enclosures with open bases, Ref.: PLAZ…
Made of fiberglass reinforced polyester.
c Colour RAL-7032.
c Self-extinguishable; high resistance to impacts and temperature.
c Double insulation; excellent resistance to weather conditions.
c 200 mm front cover accessible from the interior.
c 305 mm height fixed front panel, allowing the enclosure to be completely or partially flush built in.
c Fixing profile for cable entry.
c Sides with knock-out entry PG-36.
Plinths
Width (B) Depth (C) No. of doors
ReferenceFor attachment to enclosures
500 320 1 ZHPLA 53
750 320 1 ZHPLA 73
1000 320 2 ZHPLA 103
1250 320 2 ZHPLA 123
500 420 1 ZHPLA 54
750 420 1 ZHPLA 74
1000 420 2 ZHPLA 104
1250 420 2 ZHPLA 124
aaaaaaaaB+20
B
C
300/420
60
65To be coupled to enclosures with closed bases, Ref.: PLA…
Made of fiberglass reinforced polyester.
c Colour RAL-7032.
c Self-extinguishable; high resistance to impacts and temperature.
c Excellent resistance to outdoor conditions.
Bases
Width (B) Depth (C) No. of doors
ReferenceFor attachment to enclosures
500 320 1 ZNPLA 53
750 320 1 ZNPLA 73
1000 320 2 ZNPLA 103
1250 320 2 ZNPLA 123
500 420 1 ZNPLA 54
750 420 1 ZNPLA 74
1000 420 2 ZNPLA 104
1250 420 2 ZNPLA 124
03_084_100_EN.indd 8603_084_100_EN.indd 86 2/4/08 12:55:062/4/08 12:55:06
26
(1)
B+52A-3
7518
7,5
3/87
PLA Composition accessories
To be coupled to the models of enclosures with open plinth-type bases, Ref.: PLAZ…
Made of fiberglass reinforced polyester.
c Colour RAL-7032.
c Self-extinguishing; excellent resistance to outdoor conditions.
c Easily machined.
1-door enclosures 2-door enclosures
Cable entry plate
Width (B) Depth (C) No. of doors
ReferenceFor attachment to enclosures
500 320 1 ECPLAZ 53
750 320 1 ECPLAZ 73
1000 320 2 ECPLAZ 103
1250 320 2 ECPLAZ 123
500 420 1 ECPLAZ 54
750 420 1 ECPLAZ 74
1000 420 2 ECPLAZ 104
1250 420 2 ECPLAZ 124
100
C-7
8
C-2
04
25
63
1011
430
21 10 31
B-40
B-40
C-7
8
C-2
04
25
11
63
10
Set of 6 metal pieces in passivated zinc-coated steel.
c Fixing to the sides with 4 or 6 pieces in horizontal (1).
c In all cases, the maximum admissible load is that which corresponds to 150 kg/m2 of plate surface. See the enclosure lifting table, page 3/111.
Ref.: FMPLA.
Wall mounting kit
03_084_100_EN.indd 8703_084_100_EN.indd 87 2/4/08 12:55:082/4/08 12:55:08
C-160
B-60
3/88
PLA Composition accessories
Frame for fixing those enclosures with open plinth-type bases directly to the floor, Ref.: PLAZ…
Fixing enclosures with open bases to the floor, Ref.: PLA… is done directly, with the solution being a stud with a standard screw via the ZNPLA bottom.
Width (B) Depth (C) No. of doors
ReferenceFor attachment to enclosures
Ref.: FS/PLA2.
Floor-fixing frame
500 320 1 MFPLAZ 53
750 320 1 MFPLAZ 73
1000 320 2 MFPLAZ 103
1250 320 2 MFPLAZ 123
500 420 1 MFPLAZ 54
750 420 1 MFPLAZ 74
1000 420 2 MFPLAZ 104
1250 420 2 MFPLAZ 124
Set of 4 studs for floor fixing
Door retainers to be directly incorporated into the indicated enclosures.
c Opening of the retainer: 90º or 120º for all models. Ref. RET/PLAU.
c Opening of the retainer: 110º for models PLA, PLA...T and PLAZ.Ref. RET/PLA.
RET/PLAU
RET/PLA
Door retainer
03_084_100_EN.indd 8803_084_100_EN.indd 88 2/4/08 12:55:092/4/08 12:55:09
25
C
30*
C-40
E
D
3/89
PLA Composition accessories
Internal door manufactured in painted aluminium, grey RAL-7032.
Double bar locks, allowing change for triangle, square, etc. inserts of CRN enclosures (see general catalogue).
In enclosures with a closed bottom, Ref.: PLA, the internal PIPLA doors are coupled directly.
In models with open plinth-type base, Ref.: PLAZ..., the PTZ adapter plates must be ordered separately (see footnote).
Depth of the positioning of the internal door is adjustable 25 mm.* In enclosures with a transparent KT door, subtract 5 mm.
Internal doors
No. of doors Individual internal doors in 2-door enclosure reference*Width (B)Height (A)
Total lower door reference*D E
Weight (kg)
For attachment to enclosures Dimensions
* To be coupled to enclosures with open bottom, Ref.: PLAZ, adaptor plates must be ordered separately, Ref.: PTZ 320 or PTZ 420, for 320 or 420 mm depth one-door enclosures.
PTZ 320/2P or PTZ 420/2P must be ordered for two-door enclosures.
500 500 1 PIPLA 55 - 398 398 1.6
500 750 1 PIPLA 57 - 398 648 2.2
500 1000 2 - PIPLA 55 + PIPLA 55 - - -
500 1250 2 - PIPLA 55 + PIPLA 57 - - -
750 500 1 PIPLA 75 - 648 398 2.2
750 750 1 PIPLA 77 - 648 648 3.1
750 1000 2 - PIPLA 75 + PIPLA 75 - - -
750 1250 2 - PIPLA 75 + PIPLA 77 - - -
1000 500 1 PIPLA 105 - 898 398 2.8
1000 750 1 PIPLA 107 - 898 648 4.1
1000 1000 2 - PIPLA 105 + PIPLA 105 - - -
1000 1250 2 - PIPLA 105 + PIPLA 107 - - -
1250 500 1 PIPLA 125 - 1148 398 3.4
1250 750 1 PIPLA 127 - 1148 648 5
1250 1000 2 - PIPLA 125 + PIPLA 125 - - -
1250 1250 2 - PIPLA 125 + PIPLA 127 - - -
1500 500 1 PIPLA 155 - 1398 398 4
1500 750 1 PIPLA 157 - 1398 648 6
1500 1000 2 - PIPLA 155 + PIPLA 155 - - -
1500 1250 2 - PIPLA 155 + PIPLA 157 - - -
03_084_100_EN.indd 8903_084_100_EN.indd 89 2/4/08 12:55:102/4/08 12:55:10
3/90
PLA Composition accessories
Direct-action 5 mm double bar lock, operated with key LDB5. Included in standard supply.Accepts all the types of operation referenced in the following table by changing the inserts of the standard lock.
Embellishing kit for direct-action key-operated lock (without handle): Ref.: EB/PLA.
Standard lock for completely closed enclosures
CHANGING INSERTS OF THE STANDARD LOCK
Specifications ReferenceType of lock Type of operation
6.5 mm triangle
lock, operated TT6/CRN
with key LT6,5.
7 mm triangle
ock, operated TT7/CRN
with key LT8.
8 mm triangle
lock, operated TT8/CRN
with key LT8.
6 mm square
lock, operated TC6/CRN
with key LC7.
7 mm square
lock, operated TC7/CRN
with key LC7.
8 mm square
lock, operated TC8/CRN
with key LC8.
Double bar
lock, operated
with key LDB5. TDB/PLA
Included in
standard supply.
Padlock BC/PLA
* To obtain the complete lock, in addition to the EBM/PLA trim, the T…/OLN or T…/PLA types of locks, indi-cated on the following page, must be ordered separately.
CHANGING TO HANDLE LOCK
Specifications ReferenceType of operation
Embellishing kit
with handle lock.* EBM/PLA*
03_084_100_EN.indd 9003_084_100_EN.indd 90 2/4/08 12:55:112/4/08 12:55:11
3/91
PLA Composition accessories
Double bar handle lock, operated by key LDB5. Included in standard supply.Accepts all the types of operation referenced in the following table by changing the inserts.
Embellishing kit with handle Ref.: EBM/PLA.
* To obtain the complete lock, in addition to the CBCM/PLA trim, the T…/OLN type of lock, indicated on this page, must be ordered separately.** To obtain the complete lock, in addition to the EB/PLA trim, the T…/CRN or TDB/PLA types of locks, indi-cated on the previous page, must be ordered separately.
Standard lock for enclosures with open top or open base
CHANGING INSERTS OF THE STANDARD LOCK
7 mm triangle
lock, operated TT7/OLN
with key LT8.
8 mm triangle
lock, operated TT8/OLN
with key LT8.
6 mm square
lock, operated TC6/OLN
with key LC7.
7 mm square
lock, operated TC7/OLN
with key LC7.
8 mm square
lock, operated TC8/OLN
with key LC8.
Lock with key type 405. TL/OLN
Lock with key type JIS. TJIS/OLN
Lock with reinforced-type key TLR/OLN
Lock with key type FAC. TFAC/OLN
DIN insert
adapter. ABDIN/OLN
Pushbutton operated. TS/PLA
5 mm double
bar lock included TDBM/PLA
in standard supply.
Handle lock with CBCM/PLA*
padlocking device.*
Protective cover (optional). TPBM/PLA
CHANGING TO LOCK WITHOUT HANDLE
Specifications ReferenceType of lock Type of operation
Specifications ReferenceType of lock Type of operation
Embellishing kit without
handle lock.** EB/PLA**
03_084_100_EN.indd 9103_084_100_EN.indd 91 2/4/08 12:55:122/4/08 12:55:12
A - 158
A - 200
� 1
1
C -
116
C -
170
27
21 21
3/92
PLA Composition accessories
Support set made of the fixing supports and all the necessary hardware, for fixing the PPTR transparent protective screens to the corresponding PLA enclosures.
Made of 4 mm transparent polycarbonate. Supplied without the SPTR 77 support set, which must be purchased separately.
Transparent protective screens
Height Width
ReferenceEnclosure dimensions
500 500 PPTR 55
500 750 PPTR 57
750 500 PPTR 75
750 750 PPTR 77
Fixing supports for protective screens
Reference Application
SPTR 77 PPTR 55/57/75/77
03_084_100_EN.indd 9203_084_100_EN.indd 92 2/4/08 12:55:132/4/08 12:55:13
G
E
D F
350
437.5
H-87.5
H
E
e10.5
150
100
75
12.5
10.5 25 25
2525
25
25
25
25
Ø6.5
Ø8.5
Ø6.5
Ø8.5
150
100
75
10.5
2525
10.5
25 25
Ø 6.5
Ø 8.5
Ø 6.5Ø 8.5
3/93
PLA Mounting accessories
Made of galvanised steel sheet, with reinforcement fold on models starting with a height of 1000 mm.
Directly joined to the bottom of the enclosure itself or to the depth adjustable supports.
On two-door enclosures, a full plate or 2 partial plates may be fitted. See table.
Enclosures starting with a height of 1000 mm are equipped with intermediate fixing bosses so the PMM plates of a height less than the nominal height of the enclosure can be positioned (see note (1) below). In this case, inserts Ref.: TEX 8 must be ordered separately.
c Maximum load 150 kg/m2.
models from PMM 1010
FIG. 1 FIG. 2
Metal mounting plates
500 500 1 PMM 55 1 - - 390 375 350 350 - 2 2.5
500 750 1 PMM 75 1 - - 640 375 600 350 - 2 3.8
500 1000 2 PMM 510 2 PMM 55 + PMM 55 1 390 875 350 -0 437.5 2.5 6.3
500 1250 2 - - PMM 55 + PMM 75 1 -0 -0 -0 -0 - - -
750 500 1 PMM 75 1 - - 640 375 600 350 - 2 3.8
750 750 1 PMM 77 1 - - 640 625 600 600 - 2.5 7.8
750 1000 2 PMM 710 2 PMM 75 + PMM 75 1 640 875 600 -0 437.5 2.5 10.6
750 1250 2 PMM 712 2 PMM 75 + PMM 77 1 640 1125 600 -0 687.5 2.5 17.6
1000 500 1 PMM 105 1 - - 890 375 850 350 - 2.5 6.5
1000 750 1 PMM 107 1 - - 890 625 850 600 - 2.5 10.8
1000 1000 2 PMM 1010 2 PMM 105 + PMM 105 1 875 875 850 -0 437.5 2.5 15
1000 1250 2 PMM 1012 2 PMM 105 + PMM 107 1 875 1125 850 -0 687.5 2.5 19.3
1250 500 1 PMM 125 1 - - 1125 375 1100 350 - 2.5 8.6
1250 750 1 PMM 127 1 - - 1125 625 1100 600 - 2.5 14.2
1250 1000 2 PMM 1210 2 PMM 125 + PMM 125 1 1125 875 1100 -0 437.5 2.5 19.4
1250 1250 2 PMM 1212 2 PMM 125 + PMM 127 1 1125 1125 1100 -0 687.5 2.5 24.9
1500 500 1 PMM 155 1 - - 1375 375 1350 350 - 2.5 10.6
1500 750 1 PMM 157 1 - - 1375 625 1350 600 - 2.5 17.3
1500 1000 2 PMM 1510 2 PMM 155 + PMM 155 1 1375 875 1350 -0 437.5 2.5 23.8
1500 1250 2 PMM 1512 2 PMM 155 + PMM 157 1 1375 1125 1350 -0 687.5 2.5 30.5
(1) Enclosures of 1000, 1250 and 1500 mm height allow as partial plates: 2 PMM of 500; 1 of 500 + 1 of 750 or 2 of 750 mm height, respectively, fixed at the back of the enclosure
Height (A) Width (B)
No. of doors
Fig. No.Reference Fig. No. D E F G H e (kg)
To couple to enclosures with dimensions (1) Full plate Individual plates, two-door
enclosuresDimensions full plate
Reference
03_084_100_EN.indd 9303_084_100_EN.indd 93 2/4/08 12:55:152/4/08 12:55:15
G
E
D F
350
437.5
H-87.5
H
E
e10.510.5
150
100
75
150
100
75
10.5
10.5
3/94
PLA Mounting accessories
Made of bakelite in black RAL-9005 (Ref.: PMB..) or in polyester in grey RAL-7032 (Ref.: PMA..).
Directly joined to the bottom of the enclosure itself or to the depth adjustable supports.
On two-door enclosures, a full plate or 2 partial plates may be fitted. See table.
Enclosures starting with a height of 1000 mm are equipped with intermediate fixing bosses so the PMB plates of a height less than the nominal height of the enclosure can be positioned (see note (1) below). In this case, inserts Ref.: TEX 8 must be ordered separately.
c Maximum load 150 kg/m2.
FIG. 1 FIG. 2
Insulating mounting plates
(1) Enclosures of 1000, 1250 and 1500 mm height allow as partial plates: 2 PM.. of 500; 1 of 500 + 1 of 750 or 2 of 750 mm height, respectively, fixed at the back of the enclosure.
(2) PMA: polyester, PMB: bakelite.
500 500 1 PM.. 55 1 - - 390 375 350 350 - 4 0.9
500 750 1 PM.. 75 1 - - 640 375 600 350 - 4 1.3
500 1000 2 PM.. 510 2 PM.. 55 + PM.. 55 1 390 875 350 -0 437.5 5 2.4
500 1250 2 - - PM.. 55 + PM.. 75 1 -0 -0 -0 -0 - - -
750 500 1 PM.. 75 1 - - 640 375 600 350 - 4 1.3
750 750 1 PM.. 77 1 - - 640 625 600 600 - 5 2.8
750 1000 2 PM.. 710 2 PM.. 75 + PM.. 75 1 640 875 600 -0 437.5 5 3.9
750 1250 2 PM.. 712 2 PM.. 75 + PM.. 77 1 640 1125 600 -0 687.5 5 5
1000 500 1 PM.. 105 1 - - 890 375 850 350 - 5 2.3
1000 750 1 PM.. 107 1 - - 890 625 850 600 - 5 3.9
1000 1000 2 PM.. 1010 2 PM.. 105 + PM.. 105 1 890 875 850 -0 437.5 5 5.5
1000 1250 2 PM.. 1012 2 PM.. 105 + PM.. 107 1 890 1125 850 -0 687.5 5 7.1
1250 500 1 PM.. 125 1 - - 1140 375 1100 350 - 5 3
1250 750 1 PM.. 127 1 - - 1140 625 1100 600 - 5 5
1250 1000 2 PM.. 1210 2 PM.. 125 + PM.. 125 1 1140 875 1100 -0 437.5 5 7
1250 1250 2 PM.. 1212 2 PM.. 125 + PM.. 127 1 1140 1125 1100 -0 687.5 5 9
1500 500 1 PMB 155 1 - - 1390 375 1350 350 - 5 3.7
1500 750 1 PMB 157 1 - - 1390 625 1350 600 - 5 6.1
1500 1000 2 PMB 1510 2 PMB 155 + PMB 155 1 1390 875 1350 -0 437.5 5 8.6
1500 1250 2 PMB 1512 2 PMB 155 + PMB 157 1 1390 1125 1350 -0 687.5 5 11
Height (A) Width (B)
No. of doors
Fig. No.Reference (2) Fig. No. D E F G H e (kg)
To couple to enclosures with dimensions (1) Full plate Individual plates, two-door
enclosuresDimensions full plate
Reference (2)
Bakelite Polyester
03_084_100_EN.indd 9403_084_100_EN.indd 94 2/4/08 12:55:192/4/08 12:55:19
3/95
PLA Mounting accessories
Plates specially designed for quick mounting of equipment using the TFP locking nuts. Made of zinc-coated steel.
Directly joined to the bottom of the enclosure itself or to the depth adjustable supports.
Possibility of incorporating 2 individual plates on two-door enclosures. See table.
Enclosures starting with a height of 1000 mm are equipped with intermediate fixing bosses so the PMR plates of a height less than the nominal height of the enclosure can be positioned (see note (1) below). In this case, inserts Ref.: TEX 8 must be ordered separately.
c Maximum load 150 kg/m2.
Universal perforated mounting plates
(1) Enclosures of 1000, 1250 and 1500 mm height allow as partial plates: 2 PMM of 500; 1 of 500 + 1 of 750 or 2 of 750 mm height, respectively, fixed at the back of the enclosure.
Height (A) Width (B)
No. of doors
Reference Reference D E F GThickness
(mm))Weight (kg)
To join the enclosures (1) Full plate Individual plates, two-door enclosures
Dimensions full plate
500 500 1 PMR 55 - 370 376 350 350 2 1.1
500 750 1 PMR 57 - 370 626 350 600 2 1.7
500 1000 2 - PMR 55 + PMR 55 370 376/376 350 350/350 2 -
500 1250 2 - PMR 55 + PMR 57 370 376/626 350 350/600 2 -
750 500 1 PMR 75 - 620 376 600 350 2 1.7
750 750 1 PMR 77 - 620 626 600 600 2 2.7
750 1000 2 - PMR 75 + PMR 75 620 376/376 350 350/350 2 -
750 1250 2 - PMR 75 + PMR 77 620 376/626 350 350/600 2 -
1000 500 1 PMR 105 - 870 376 850 350 2 2.1
1000 750 1 PMR 107 - 870 626 850 600 2 4.1
1000 1000 2 - PMR 105 + PMR 105 870 376/376 850 350/350 2 -
1000 1250 2 - PMR 105 + PMR 107 870 376/626 850 350/600 2 -
1250 500 1 PMR 125 - 1120 376 1100 350 2 3.3
1250 750 1 PMR 127 - 1120 626 1100 600 2 4.8
1250 1000 2 - PMR 125 + PMR 125 1120 376/376 1100 350/350 2 -
1250 1250 2 - PMR 125 + PMR 127 1120 376/626 1100 350/600 2 -
1500 500 1 PMR 155 - 1370 376 1350 350 2 4.2
1500 750 1 PMR 157 - 1370 626 1350 600 2 6.3
1500 1000 2 - PMR 155 + PMR 155 1370 376/626 1350 350/350 2 -
1500 1250 2 - PMR 155 + PMR 157 1370 376/626 1350 350/600 2 -
F
D
GE
15
03_084_100_EN.indd 9503_084_100_EN.indd 95 2/4/08 12:55:212/4/08 12:55:21
3/96
PLA Mounting accessories
c Allow for depth adjustment of PMM, PMB and PMR mounting plates, on any model of enclosure.
c Set of 4 adjustable supports on the profile of the aluminium guide, able to be fixed at any point along its entire length and with reference positioning every 25 mm.
c Models with a closed base. Ref.: PLA...The DPLA adjustable supports can be coupled directly without the need for other accessories.
Detail of DPLA plate supports in enclosure with closed base.
62*
C
35
C-70
62*
C
35
C-70
* For enclosures with a transparent KT door, subtract 5 mm.
enclosure with open plinth-type base, reference PLAZ… , with two doors, with adjustable plate fixed with DPLA supports and PTZ adaptor plates.
Set of 4 adjustable fixing supports for fixing an additional plate.
Ref.: EDPLA.
Detail of the DPLA plate supports with an additional set of fixing supports, Ref.: EDPLA, allowing the placement of two plates (back to back), for example in enclosures with a rear door.
PTZ 420
PTZ 420/2P
Set of adjustable mounting plate supports
c Two-door modelsTwo sets of DPLA adjustable supports must be ordered, and for the models open bottom, add one PTZ.../2P set.
* In two-door enclosures, in order to mount a full plate or two individual plates, 2 DPLA plate fixing sets must
be ordered, as indicated in the table.
To be installed in enclosures To be installed in enclosures reference
Depth (C) No. of doors PLA... PLAZ...
320 1 DPLA 320 DPLA 320 + PTZ 320
420 1 DPLA 420 DPLA 420 + PTZ 420
320 2 (2�) DPLA 320* (2�) DPLA 320* + PTZ 320/2P
420 2 (2�) DPLA 420* (2�) DPLA 420* + PTZ 420/2P
c Models with open plinth-type base. Ref.: PLAZ... In addition to the DPLA adjustable supports, a set of PTZ adaptor plates must be ordered.
DPLA 420
Set of fixing supports for additional plate
03_084_100_EN.indd 9603_084_100_EN.indd 96 2/4/08 12:55:222/4/08 12:55:22
Detail of the MOL profile fixed to the back of the enclosure.
3/97
CDP double profile DIN rail for direct fixing of equipment. Detail of the TDC sliding nut.
Detail of the MOL profile and TDM nut.The notches in the profile permit adjustment every 2.5 mm.
Set of two vertical profiles for direct fixing to the back of the enclosure.The notches in the profile every 2.5 mm and the marks every 25 mm facilitate the positioning of plates, rails, etc.
To make depth adjustment of the chassis possible, the MOL profiles must be fixed on a set of DPLA or DPLA + PTZ adjustable mounting plate supports, as in the following table.
Detail of the MOL profile fixed to the set of DPLA adjustable plate support.
PLA Mounting accessories
Universal chassis system
Set of profiles for universal chassis
Depth (C) No. of doors PLA... PLAZ...
To be installed in enclosures To be installed in enclosures reference
320 1 DPLA 320 DPLA 320 + PTZ 320
420 1 DPLA 420 DPLA 420 + PTZ 420
320 2 (2�) DPLA 320 (2�) DPLA 320 + PTZ 320/2P
420 2 (2�) DPLA 420 (2�) DPLA 420 + PTZ 420/2P
To couple to enclosures with height (A) Reference
750 MOL 75
1000 MOL 100
1250 MOL 125
1500 MOL 150
Universal chassis made up of a set of 2 MOL profiles prepared for partial mounting plates and DIN rails, for fixing any type of equipment.
The chassis can be fixed directly to the back of the enclosure or on the set of adjustable mounting plate supports, in this case making depth adjustment possible.
In two-door enclosures with 1000 and 1250 mm width, two 500 mm chassis, or 1 of 500 + 1 of 750 mm width, respectively, can be mounted.
03_084_100_EN.indd 9703_084_100_EN.indd 97 2/4/08 12:55:242/4/08 12:55:24
B - 100
A - 100
45°
40
20
44,5
7
77
44,5
40
7
10
B-95
H
3/98
Insulating polyester mounting plates, to be installed on the side of PLA enclosures.
The TEX8 inserts must be ordered separately.
Lateral mounting plates
Height Depth
ReferenceEnclosure dimensions
500 320 PMLA 53
500 420 PMLA 54
750 320 PMLA 73
750 420 PMLA 74
1000 320 PMLA 103
1000 420 PMLA 104
1250 320 PMLA 123
1250 420 PMLA 124
Made of galvanised steel. They are placed on the MOL profiles using TDM 8 nuts and TOR 16/8A screws, which must be ordered separately.
To couple to enclosures with width (B)
Plate height (H)
Reference
500 247 PMP 2550
750 247 PMP 2575
1000* 247 PMP 25100
500 397 PMP 4050
750 397 PMP 4075
1000* 397 PMP 40100
* The 1000 mm width enclosures allow for mounting 2 chassis with PMP...50 plates.
PLA Mounting accessories
Partial mounting plates for universal chassis
03_084_100_EN.indd 9803_084_100_EN.indd 98 2/4/08 12:55:312/4/08 12:55:31
3/99
PLA Mounting accessories
Rails of galvanised steel. They are placed on the MOL profiles using TDM 6 nuts and TOR 12/6A screws, which must be ordered separately.
* The 1000 mm width enclosures allow for mounting 2 chassis with C...50 rails.
Metal rails and nuts
To couple to enclosures with width (B)
Double profile reference
Symmetric DIN reference35 � 7.5
Symmetric DIN reference35 � 15
Asymmetric DIN reference
500 - CSPLA 50 CAPLA 50 -
750 - CSPLA 75 CAPLA 75 -
1000 - CSPLA 100 CAPLA 100 -
In 2 metre strips CO 35 - CA 32 CDP 200
In 2 metre strips COT 35 - CAT 32 -
In 2 metre strips - CO 35/15 - -
In 2 metre strips - COT 35/15 - -
(1) For symmetrical rails, Ref.: CO, COT and CSPLA, and double profile CDP...
(2) For double profile rails CDP...
Thread typeUnits per package Units per package Length (mm) Units per package
Nuts for fixing equipment Nuts for MOL profiles Fixing screw with washer
Units per package
M4 TDE 4 100 - 100 - - TOR 10/4A 10 100
M4 - - - - - - TOR 16/4A 16 100
M5 TDE 5 100 - - - - TOR 12/5A 12 100
M5 - - TDC 56 100 - - TOR 18/5A 18 100
M6 TDE 6 100 TDC 56 100 TDM 6 10 TOR 12/6A 12 100
M6 - - - - - - TOR 18/6A 18 100
M8 - - - - TDM 8 10 TOR 16/8A 16 50
M8 - - - - - - TOR 20/8A 20 10
Sheet ∅ 4.8 mm TOR 16/5AT 16 100
MOUNTING ACCESSORIES
(2)(1)
03_084_100_EN.indd 9903_084_100_EN.indd 99 2/4/08 12:55:332/4/08 12:55:33
12
18
C-1
00
25
B-4227
12
250
200
200
200
200
11x13
3/100
PLA Mounting accessories
BANPLA tray to be placed horizontally to support various materials, or simply as a separator. Designed to be installed in one-door enclosures.
It is mounted directly on the bottom of the enclosure using the lateral bosses.
If you want to place the tray, or various trays, at differing heights, 2 sets of 2 SPLA vertical profiles (total of 4), must be ordered, as indicated in the table.
Maximum load:Depth 320: 60 kgDepth 420: 50 kg
* Are only necessary if you want to place the tray at differing heights.
(1) For the 1250 mm enclosures, these trays may be placed using the SBPLA profiles, on the 500 and
750 mm side.
Support tray
Height (A) Width (B) Depth (C)
ReferenceTo couple to enclosures (1)
500 500 320 BANPLA 53 -
500 750 320 BANPLA 73 -
750 500 320 BANPLA 53 2 � SPLA 75
750 750 320 BANPLA 73 2 � SPLA 75
1000 500 320 BANPLA 53 2 � SPLA 100
1000 750 320 BANPLA 73 2 � SPLA 100
1250 500 320 BANPLA 53 2 � SPLA 125
1250 750 320 BANPLA 73 2 � SPLA 125
1500 500 320 BANPLA 53 2 � SPLA 150
1500 750 320 BANPLA 73 2 � SPLA 150
500 500 420 BANPLA 54 -
500 750 420 BANPLA 74 -
750 500 420 BANPLA 54 2 � SPLA 75
750 750 420 BANPLA 74 2 � SPLA 75
1000 500 420 BANPLA 54 2 � SPLA 100
1000 750 420 BANPLA 74 2 � SPLA 100
1250 500 420 BANPLA 54 2 � SPLA 125
1250 750 420 BANPLA 74 2 � SPLA 125
1500 500 420 BANPLA 54 2 � SPLA 150
1500 750 420 BANPLA 74 2 � SPLA 150
Tray Supports*
For 19” RACK accessories, consult the VDI catalogue.
Ref.: SB/PLA.
19” rack support and trays for two-door enclosures
03_084_100_EN.indd 10003_084_100_EN.indd 100 2/4/08 12:55:382/4/08 12:55:38
3/101
PLA Current distribution accessories
Clip in fasteners to be installed directly on 19” racks and on slotted MR mounting plates.
Reference: GCR.
GCR ties
Made of 6.6 nylon in natural colour or black for outdoor conditions.
Adjustable ties
White BlackL ∅
minimum∅
maximum
M
Reference Use
LZ25100 LN25100 100 2.5 1.6 22
LZ25200 LN25200 200 2.5 1.6 49
LZ35150 LN35150 150 3.5 1.6 35
LZ35200 LN35200 200 3.5 1.6 49
LZ35300 LN35300 300 3.5 1.6 75
LZ46150 LN46150 150 4.6 1.6 36
LZ46200 LN46200 200 4.6 1.6 49
LZ48270 LN48270 270 4.8 1.6 73
LZ46390 LN46390 390 4.6 1.6 109
LZ76390 LN76390 390 7.6 4.7 108
To tighten and cut to size the adjustable ties. They facilitate wiring and save time, preventing the packets of cables from loosening.
Tool adjustable according to the thickness of the tie. Can be used with the following models: LZ25100 up to LZ46390. Ref.: MARK3.
A very light and ergonomic tool, the cut on the tie is done by twisting the tool. Can be used on the following models of ties: LZ25100 up to LZ46390. Ref.: MARK20, 21.
Tightening tools
Reference
MARK3 2.5 ÷ 4.8
Admissible width ties
Reference
MARK20 2.5 ÷ 4.8
MARK21 4.6 ÷ 7.6
Admissible width ties
03_101_107_EN.indd 10103_101_107_EN.indd 101 2/4/08 12:57:002/4/08 12:57:00
3/102
PLA Current distribution accessories
To use with soft materials: 7 mm Ø hole, or hard materials: 8 mm Ø hole. Ties are attached up to 9 mm width. Material: 6.6 nylon
Ref.: LOK01.
Stud
To attach one or two ties, mounted with a single screw. Material: 6.6 nylon. Allows for attaching ties from the entire range.
Tie fixing support
Reference A B Fixing screwAdmissible width
tiesC
KR6 12 18 9 M4 2.5 ÷ 4.8
KR8 14.5 25 12 M6 2.5 ÷ 7.6
Allows fixing ties from the series LZ25100 up to LZ46390 on panels up to 3.2 mm thick. Material: 6.6 nylon.
Locking clips
Reference
SFC1 6 3.2 1
SFC2 6 1 2
FigureMaximum width
panel mm∅ perforation
mm
SFC2 SFC1
Fig. 1 Fig. 2
03_101_107_EN.indd 10203_101_107_EN.indd 102 2/4/08 12:57:012/4/08 12:57:01
3/103
PLA Current distribution accessories
To transform normal ties into ties with fixing heads, introduce a tie into this head before closing it on the cable bundle. Material: 6.6 nylon.
Support heads
Reference A B Fixing screwAdmissible width ties
C
FH18 7.1 13.3 4 M4 2.5
FH30 9.5 17.9 4.7 M5 3.5
FH50 11.3 22.2 6.2 M6 4.7
Permits insertion of 1 tie from 4 points at a 90º angle. Attaches ties from the series LZ25100 up to LZ46390. Material: 6.6 nylon.
Self-adhesive support base
Reference A B C EAdmissible width
tiesD
MB3A 19.1 19.1 4.8 3.2 13.2 2.5 ÷ 3.5
MB4A 28.5 28.5 5.5 4 20.2 2.5 ÷ 4.8
To attach ties from any series. Material: 6.6 nylon.
Tie fixing support
Reference
LKC 2.5 � 7.6 M5
Fixing screwAdmissible width
ties mm
adhesive support
03_101_107_EN.indd 10303_101_107_EN.indd 103 2/4/08 12:57:032/4/08 12:57:03
3/104
PLA Current distribution accessories
2 versions, fixed and graduated, ∅ from 5 to 25.4 mm. Material: black 6.6 nylon.
Fixing loop for tubes, hoses, etc.
Reference∅ A
min. - max.B D EC
NX1 5 3.5 1 6.2 13.7
NX3 8 3.9 1 9.4 20.5
NX5 12 3.9 1 9.4 24
NX8* 14.3 ÷ 15.8 4 1.3 12.6 32
NX11 17.4 ÷ 20 4 1.3 12.6 37
NX14 22.2 ÷ 25.4 4.3 1.5 16 45
*The NX8 model only has 3 adjustment holes.
NX 1-3-5 NX 8-11-14
Covers the head of the tie in its end, thus obtaining neater cabling. Material: 6.6 nylon.
Lateral tie fixing support
Reference
LKM/HE 2.5 � 7.6 M5
Fixing screwAdmissible width
ties mm
03_101_107_EN.indd 10403_101_107_EN.indd 104 2/4/08 12:57:042/4/08 12:57:04
3/105
PLA Current distribution accessories
Insulating membrane glands made of PVC with entry that can be adjusted for cables.
Adjustable membrane glands
Reference Fig. Ø A Ø B* Ø C Ø D E FØ cable Tube
Capacity
ECPC-3 1 25 21.5 18 5 3.2 13 5 to 18 Pg 9 to 11
ECPC-5 1 33 29.5 26 5 3.2 20 5 to 26 Pg 9 to 16
ECPC-6 1 43 38.5 36 5 3.2 22 5 to 36 Pg 9 to 21
ECPC-9 2 70 63 60 28 3 20 28 to 60 Pg 21 to 48
ECPC-15 2 98 90 87 28 3 23 28 to 87 Pg 21 to 48
* Mounting perforation.
Fig. 1 Fig. 2
Ø A
Ø B
Small protective sleeves for cables coming out of tubes, as indicated in the instructions for MI BT 019. Made of flexible and durable PVC, in light grey colour.
Protective sleeves
Reference A Ø B Tube
PC-1 15.2 12.7 Pg 9
PC-2 18.6 16 Pg 11
PC-3 20.4 17.8 Pg 13.5
PC-4 22.5 19.8 Pg 16
PC-5 28.3 25.3 Pg 21
PC-6 37 33.6 Pg 29
PC-7 47 43 Pg 36
03_101_107_EN.indd 10503_101_107_EN.indd 105 2/4/08 12:57:042/4/08 12:57:04
3/106
PLA Current distribution accessories
Øexterior
SteelFlexible
steelPVC Insert Thread
Protective sleeves
Adjustable membrane
glandsPlain plugs
Adjustable membrane glands
Flexible steel with
PVC
Cables inserted*Ø interior To the perforationsTo the tubes
4 EC-1 to EC-7
Pg 9 15.2 12.7 12.4 12 11.1 6 2.5 - - 16 14 ECPC-3 to ECPC-6 PC-1 - -
ECN-5 to ECN-10
10 4 2.5 EC-2 to EC-7 EC-1
Pg 11 18.6 16 15.5 14.5 14.2 16 6 4 2.5 19 17.5 ECPC-5; ECPC-6 PC-2 EC-2 TC-1
25 ECN-5 to ECN-10 ECN-1
EC-3 to EC-7 EC-3
Pg 13.5 20.4 17.8 17.5 16.3 16 35 10 6 4 21 19.5 ECPC-5; ECPC-6 PC-3 ECPC-3 TC-2
ECN-5 to ECN-10
EC-4 to EC-7
Pg 16 22.5 19.8 18.7 18.5 17.6 50 16 10 6 23 21.5 ECPC-5; ECPC-6 PC-4 EC-4 TC-3
ECN-5 to ECN-10
EC-5 to EC-7 EC-5
Pg 21 28.3 25.3 24.7 23 23 70 25 16 10 29 27 ECPC-6 to ECPC-15 PC-5 ECPC-5 TC-4
ECN-6 to ECN-10 ECN-5
95 35 25 16 EC-6; EC-7 EC-6 TC-5
Pg 29 37 33.6 33.5 31 31 120 50 35 25 38 35.5 ECPC-9; ECPC-15 PC-6 ECPC-6 TCP-5
150 ECN-7; ECN-10 ECN-6
185 35 EC-7 EC-7
Pg 36 47 43 41.5 41 40.3 240 70 50 50 48 45.5 ECPC-9; ECPC-15 PC-7 ECN-7 TC-6
300 ECN-10
95 70 ECPC-9; ECPC-15
Pg 42 54 50 48 48 47 - 120 95 70 55 52.5 ECN-10 - - -
120 95 ECPC-9; ECPC-15
Pg 48 60 56 54.2 52.5 51.4 - 150 150 120 61 58 ECN-10 - - -
* Number and section in mm2 of the conductors that may be housed inside each tube (orientative).
For more information, consult the electrotechnical rules for low voltage (MI BT 019).
1 2 3 4
MODELS, DIMENSIONS AND REFERENCES
No. of conductors
Tubes HIMEL accessories to be coupled
Useful information about Pg tubes and HIMEL accessories to be coupled
Ø perforations to
Terminals especially designed for branching cables on plates; their main application is busbar connection.
BBH terminals are made of a tinned, hot cast copper alloy and are suitable for connecting to a conductor of copper or aluminium indistinctly (bimetal).
Bimetal BBH terminals
Reference
BBH-29 6-50 -
BBH-29C* 6-50 -
BBH-30 10-95 -
BBH-31 16-150 -
BBH-32 50-240 -
BBH-29D 6-50 6-50
BBH-29DC* 6-50 6-50
BBH-30D 10-95 10-95
BBH-31D 25-150 16-150
BBH-32D 95-240 5-240
Main section (mm2)
Bypass section (mm2) Reference
BBH-29P 6-50 -
BBH-29PC* 6-50 -
BBH-29DP 6-50 6-50
BBH-29DPC* 6-50 6-50
* Include terminal cover CBBH-29.
Main section (mm2)
Bypass section (mm2)
BBH-29 BBH-29D
BBH-29P BBH-29DP
Desig-nation
03_101_107_EN.indd 10603_101_107_EN.indd 106 2/4/08 12:57:052/4/08 12:57:05
3/107
ReferenceCable bypass section
(mm2)Plate thickness (mm) Figure
BPCH 516 1.5 to 16 5 2
BPCH 550 1.5 to 50 5 2
BPCH 5120 16 to 120 5 2
BPCH 1016 1.5 to 16 10 1
BPCH 1050 1.5 to 50 10 1
BPCH 10120 16 to 120 10 1
PLA Current distribution accessories
Base of safety terminals made of black matte self-extinguishing polyamide-6; terminal of brass MS-58
(DIN17660); ring of tempered steel zinc dichromate; cap made of orange self-extinguishing polypropylene.
c Anti-cut. The connection is made using a tightening mechanism that spreads the pressure out throughout the entire contact surface, avoiding the occasional rubs and stresses that damage the conductors.
c Loosening proof. The ring that surrounds the brass body ensures that the pressure exerted by the conductors cannot open the terminal and loosen the connection.
c Total insulation. All the SIGMA terminals are supplied with a terminal cap, avoiding any accidental contact with live parts.
All the calibres may be coupled one to the other, allowing the formation of strips of any length. Service voltage: 500 V.
Sigma safety terminals
Reference
S.04 1 × 4 30 20 13 21 4
S.06 1 × 6 33 25 16 24 7
S.10 1 × 10 38 28 16 28 6
S.16 1 × 16 42 32 19 32 9
S.25/35 1 × 35 46 38 23 34 11
S.50 1 × 50 52 45 27 40 15
S.70 1 × 70 55 50 30 40 15
S.95/100 1 × 100 58 54 33 40 20
NOTE: each terminal accepts up to 2 conductors of the section indicated.
Sectionm/m2 A B C D E
Plate entry and bypass by cable.
Plate/cable terminals
1 2
03_101_107_EN.indd 10703_101_107_EN.indd 107 2/4/08 12:57:072/4/08 12:57:07
35590
7066
3/108
PLA Lighting accessories
Compact lamp
Specifications TensionPlugReference
Lamp fixed with a magnet
or on 35 mm symmetric LAM-75 220 V/16 A 220 V/50 Hz
DIN rail
Lamp fixed on a 35 mm
symmetric DIN rail LAC-75 220 V/16 A 220 V/50 Hz
Lamp fixed with a magnet
or on 35 mm symmetric LAM-75/120 120 V/15 A 120 V/60 Hz
DIN rail
Lamp fixed on a 35 mm
symmetric DIN rail LAC-75/120 120 V/15 A 120 V/60 Hz
Compact fluorescent lamps, designed especially for use in electronic enclosures. May be fixed with a magnet.
c Connection voltage 220 V/50 Hz.
c Consumption 11 W.
c Connection/disconnection switch.
c 200 V/16 A socket with earthing.
c Maximum ambient temperature 60 °C.
c Lighting output = 75 W bulb.
Magnetic-fixing flat lamps equipped with energy efficient light bulbs, with or without a plug.
c Electronic ballast.
c Power: 11 W.
c Luminosity: 900 lm
c Lifespan: 10000 h.
c Plastic casing UL94 V0.
c IP20.
c Class I.
Slimline lamp
Reference Plug Socket Approval
LAMS75 AC 230 V/16 A SCHUKO VDE
LAMX75 AC 230 V/- - VDE
LAMU75 AC 120 V/15 A USA UL
03_108_109_EN.indd 10803_108_109_EN.indd 108 5/3/08 11:29:425/3/08 11:29:42
3/109
PLA Lighting accessories
396
67
100
Dual lamp
1
2
3
4
Specifications Support fixing Figure Reference Tension
Motion-activated
Magnetic, using screws LAMDP 220 V/56 Hz
and/or (1) 35 DIN rail 1 LAMDP 120 120 V/60 Hz
On/off switch with the possibility Magnetic, via connection LAMIN 220 V/50 Hz
of door switch, screws and/or 35 DIN rail (1) 2 LAMIN 120 120 V/60 H
Mobile lamp, connection Adhesive or screws
LAMPO 220 V/50 Hz
via cable 3 LAMPO 120 120 V/60 Hz
Support for LAMDP, Adhesive or screws
LAMIN, LAMPO lamp 4 SOLAM
(1) DIN rail not provided..
Light fixtures designed especially for use in electronic enclosures with various possibilities for fixing and operating.
c Energy efficient electronic lamp E27, 20 W, 220-240 V/50-60 Hz or 120 V/60 Hz.
c Lighting output = 100 W bulb.
c Fixed models connection via 2.5 mm2 terminal strip and the mobile model via cable.
c Degree of protection IP20.
c Insulation class II.
c Conforming to EN 55014 and EN 50082-1.
Incandescent lamp designed especially for use in electronic enclosures.
c Connection voltage 220 V/50-60 Hz.
c Consumption 60 W.
c Connection/disconnection switch.
c Terminal connection entry.
Incandescent lamp
Reference
LAI/OL 68
500
03_108_109_EN.indd 10903_108_109_EN.indd 109 5/3/08 11:29:485/3/08 11:29:48
3/110
PLA Natural ventilation accessories
To connect the inside of the enclosure with the exterior atmosphere and prevent condensation. Can be fixed onto the outside.
VM-25 VM-27
Ventilation devices
VM-25 For coupling to the outside of all polyester enclosures
VM-27
SpecificationsReference
03_110_117_EN.indd 11003_110_117_EN.indd 110 2/4/08 12:58:142/4/08 12:58:14
174
188 22 278 40
234
3/111
Plan size
A4 PP-A4
A5 PP-A5
Reference
Insulated
PLA Complementary accessories
PP-A models made of thermoplastic in grey RAL-7035.
c Fixed with adhesive tape or screws.
For holding DIN A3-A4 or A5-sized plans.
Document pocket
Ref.: PP-A5 Ref.: PP-A4
Dodge-type brass nuts designed to be incorporated into the bosses of PLM enclosures.
Expandable nuts
M5 PLM-43 and 54 TEX 5
M6 PLM-64 and 108 TEX 6
M8 For the back of the enclosure TEX 8
ReferenceSpecifications For attachment to enclosures
There is a set of slings to cover the most common enclosure or suite lifting needs.
Ref: ELS 1520.
c Table of dimensions indicating the maximum weight in kg anticipated for each enclosure or suite. The fields highlighted indicate the dimensional range of use planned for the lifting equipment ELS 1520.
(A) and (B) correspond, respectively, to the nominal height and width in mm of the enclosures or suites.
Lifting the enclosures
500 750 1000 1250 1500 1750 2000
1500 113 169 225 281 338 394 450
1200 94 141 188 234 281 328 375
1000 75 113 150 188 225 263 300
750 56 84 113 141 169 197 225
500 38 56 75 94 113 131 150
Width (B)Height (A)
TEX 8 TEX 6 TEX 5
03_110_117_EN.indd 11103_110_117_EN.indd 111 2/4/08 12:58:142/4/08 12:58:14
3/112
DLP distribution chassis set for modular equipment, to be coupled to all models of PLA enclosures.
c Distance of 40 to 85 mm, adjustable as needed by the customer, between the symmetric profile for equipment fixing and the interior protective cover.
c Rigid structure made of galvanised steel.
c Cover and frame insulating in self-extinguishing material in RAL-7032. Quick mounting, without the need for screws.
c System for identifying circuits included in the standard supply.
c Earth and neutral bypass terminal block, Ref.: RBLZ/21656 (included in standard supply).
c Possibility of installing plain mounting plates and covers to mount various material.
In enclosures with a closed base, Ref.: PLA… the 1500 height DLP chassis are coupled directly.
In models with open plinth-type bottom, Ref.: PLAZ should be ordered separately from the PTZ adapter plates (see footnote).
PLA Applications
* To be coupled to enclosures with open bottom, Ref.: PLAZ adaptor plates must be ordered separately, Ref.: PTZ 320 or PTZ 420, for 320 or 420 mm depth one-door enclosures.
PTZ 320/2P or PTZ 420/2P must be ordered for two-door enclosures.
MODELS, DIMENSIONS AND REFERENCES
No. of doors Individual chassis on two-door enclosures reference*Width (B)Height (A)
Total chassis reference*No. of rows
Automatic switch rail
Quantity No. of 18 mm modulesNo. of plates
For attachment to enclosures Distribution of rows
750 500 1 DLP 76 - 4 4 76 -
750 500 1 DLP 57 - 4 3 57 1
750 750 1 DLP 132 - 4 4 132 -
750 750 1 DLP 99 - 4 3 99 1
750 1000 2 - DLP 76 + DLP 76 4 + 4 4 + 4 152 -
DLP 57 + DLP 57 4 + 4 3 + 3 114 1 + 1
750 1250 2 - DLP 76 + DLP 132 4 + 4 4 + 4 208 -
DLP 57 + DLP 99 4 + 4 3 + 3 156 1 + 1
1000 500 1 DLP 114 - 6 6 114 -
1000 500 1 DLP 95 - 6 5 95 1
000 750 1 DLP 198 - 6 6 198 -
1000 750 1 DLP 165 - 6 5 165 1
1000 1000 2 - DLP 114 + DLP 114 6 + 6 6 + 6 228 -
DLP 95 + DLP 95 6 + 6 5 + 5 190 1 + 1
1000 1250 2 - DLP 114 + DLP 198 6 + 6 6 + 6 312 -
DLP 95 + DLP 165 6 + 6 5 + 5 260 1 + 1
1250 500 1 DLP 133 - 7 7 133 -
1250 500 1 DLP 114P - 7 6 114 1
1250 750 1 DLP 231 - 7 7 231 -
1250 750 1 DLP 198P - 7 6 198 1
1250 1000 2 - DLP 133 + DLP 133 7 + 7 7 + 7 266 -
DLP 114P + DLP 114P 7 + 7 6 + 6 228 1 + 1
1250 1250 2 - DLP 133 + DLP 231 7 + 7 7 + 7 364 -
DLP 114P + DLP 198P 7 + 7 6 + 6 312 1 + 1
1500 500 1 DLP 171 - 9 9 171 -
1500 500 1 DLP 152 - 9 8 152 1
1500 750 1 DLP 297 - 9 9 297 -
1500 750 1 DLP 264 - 9 8 264 1
1500 1000 2 - DLP 171 + DLP 171 9 + 9 9 + 9 342 -
1500 1000 2 - DLP 152 + DLP 152 9 + 9 8 + 8 304 -
1500 1250 2 - DLP 171 + DLP 297 9 + 9 9 + 9 468 1 + 1
1500 1250 2 - DLP 152 + DLP 264 9 + 9 8 + 8 416 1 + 1
DLP distribution system chassis
03_110_117_EN.indd 11203_110_117_EN.indd 112 2/4/08 12:58:182/4/08 12:58:18
85
40
2546
150
85
440
8585
40
85
40
45C-178C-mín.
40
16
C
3/113
Detail of the depth-adjustable rail using a graduated support included in the standard supply.
Covers that are quick fixing by pressure and removable using screwdriver.
Label for identifying circuits included in the standard supply.
FIG. 1
FIG. 2
Positioning the adjustable chassis at a depth of 25 mm.
* For enclosures with a transparent KT door, subtract 5 mm.
PLA Applications
(500)(1500)
DLP 171
(500)(1250)
DLP 133
(500)(1000)
DLP 114
(500)(750)
DLP 76
(750)(1500)
DLP 297
(750)(1250)
DLP 231
(750)(1000)
DLP 198
(750)(750)
DLP 132
(500)(1500)
DLP 152
(500)(1250)
DLP 114P
(500)(1000)
DLP 95
(500)(750)
DLP 57
(750)(1000)
DLP 165DLP 99
(750)(750)
(750)(1500)
DLP 264
(750)(1250)
DLP 198P
03_110_117_EN.indd 11303_110_117_EN.indd 113 2/4/08 12:58:182/4/08 12:58:18
3/114
Self-extinguishing plain cover to protect non-modular material.
c Colour RAL-7032.
c Easily machined.
c Quick mounting.
c 150 mm nominal height for 1 row.
2 mm thick mounting plate for fixing non-modular equipment, made of galvanised steel.
c Direct fixing to the adjustable support, which permits a depth adjustment of between 40 and 85 mm with respect to the cover.
c 150 mm nominal height for 1 row.
149
D
10×45°
E
PLA Applications
Plain cover
Mounting plate
Plate heightEnclosure width
(B)Reference D E
150 500 PMP500/DLP 361 149
150 750 PMP750/DLP 611 149
150 500 PMP500/2DLP 361 298
300 750 PMP750/2DLP 611 298
25 25
146
2113
D
To be coupled to nominal-width enclosures (B)
Reference D
500 CTL500/DLP 402
750 CTL750/DLP 652
500 CTL500/2DLP 402
750 CTL750/2DLP 652
03_110_117_EN.indd 11403_110_117_EN.indd 114 2/4/08 12:58:202/4/08 12:58:20
3/115
Earth or neutral bypass terminal blocks with insulating plinth.
Fixed to the back of the enclosure using the metal profile.
For the distribution in a single row of automatic switches with a total of 12 modules.
1 2
3 4
PLA Applications
Blanking plate
Bypass terminal blocks
* Included in standard supply.
Reference Number of terminals 3 section in mm2
RBLZ/21656* 2 � 16 mm2 + 5 � 6 mm2
RBLZ/21686 2 � 16 mm2 + 8 � 6 mm2
RBLZ/216146 2 � 16 mm2 + 14 � 6 mm2
RBLZ/216296 2 � 16 mm2 + 29 � 6 mm2
Distribution bars
No. of bars No. of poles per bar Reference Figure No.
1 12 BDS 1/12 1
2 6 BDS 2/6 2
3 4 BDS 3/4 3
4 3 BDS 4/3 4
Blanking plate of self-extinguishing insulating material for total or partial coverage of the windows for automatic switches. Easily cut to the desired size.
ATP6/DTM 108 6
ATP24/DTM 432 24
ATP/UND 1100 Cut to size
No. of modulesLength (mm)Reference
03_110_117_EN.indd 11503_110_117_EN.indd 115 2/4/08 12:58:222/4/08 12:58:22
3/116
System of very robust 19” metal racks, to be coupled to all versions of PLA enclosures with dimensions indicated on the following page.
c Fixed and pivoting racks, permitting direct installation (using standardised perforations) of all types of 19” modular switchgear.
c Fixing the racks on the upper part and the sides of the corresponding enclosure, using SPLA vertical profiles, which must be ordered separately from 750 mm height enclosures. See tables on the next page.
c Both the fixed and the pivoting racks can be installed as partial racks in enclosures that are larger than the foreseen normal. See tables on the next page.
c Maximum load: 3 kg per unit, with a maximum of 40 kg for pivoting racks.
c Finish: polyester-epoxy RAL-7032 paint.
c Pivoting racks with opening to 120º, 5 mm key-operated double bar lock.
➀ Fixed rack BRF 17PLA fixed using the set of two vertical profiles SPLA 100.
➁ Pivoting rack BRP 16PLA fixed using the set of two vertical profiles SPLA 100.
➂ Pivoting rack BRP 7PLA installed as a partial rack in enclosure. PLA 1074KT fixed using the set of two vertical profiles SPLA 100.
➂
➁
➀
PLA Applications
System of 19” racks
For 19” accessories, consult the VDI catalogue.
Ref.: SB/PLA.
19” rack support and trays for two-door enclosures
03_110_117_EN.indd 11603_110_117_EN.indd 116 2/4/08 12:58:232/4/08 12:58:23
31.7
5
485
465
450
55
750
77
300
420
12.7
44.4
544
.45
8.5 x 8.5
750
31.7
512
.7
44.4
544
.45
420
465
450
8.5 x 8.5
325
44
3/117
BRF racks prepared to be coupled to all 750 mm width PLA enclosure models.From the 750 mm height enclosures, the set of two vertical profiles SPLA, indicated in the table, must be ordered.
BRF...
SPLA...
BRP racks prepared to be coupled to all 750 mm width and 420 mm depth PLA enclosure models.From the 750 mm height enclosures, the set of two vertical profiles SPLA, indicated in the table, must be ordered separately.
BRP...
SPLA...
PLA Applications
19” fixed rack
* Can be installed in taller enclosures as a partial rack, using the vertical profiles that correspond to the height of the enclosure. In all cases, the SPLA vertical profiles must be ordered separately.(1) It can also be installed in the 1250 mm enclosures, on the 750 mm side, using the SBPLA profiles.
Height (A)
For attachment to enclosures
Width (1) (B)No. of units Reference rack Set of two profiles
500* 750 8 BRF 8PLA* -
750* 750 12 BRF 12PLA* SPLA 75
1000* 750 17 BRF 17PLA* SPLA 100
1250* 750 21 BRF 21PLA* SPLA 125
1500* 750 26 BRF 26PLA SPLA 150
19” pivoting rack
* Can be installed in taller enclosures as a partial rack, using the vertical profiles that correspond to the height of the enclosure. In all cases, the SPLA vertical profiles must be ordered separately.
Height (A)
For attachment to enclosures
Width (B)No. of units Reference rack Set of two profiles
500* 750 7 BRP 7PLA* -
750* 750 11 BRP 11PLA* SPLA 75
1000* 750 16 BRP 16PLA* SPLA 100
1250* 750 20 BRP 20PLA* SPLA 125
1500* 750 25 BRP 25PLA SPLA 150
19” fixed rack 19” pivoting rack
03_110_117_EN.indd 11703_110_117_EN.indd 117 2/4/08 12:58:242/4/08 12:58:24