PIX Hydraulic Hose is useful for medium pressure service with high petroleum base hydraulic fluids, carrying hot oils, grease, lubricants, Crude oil, fuel oil and water. It is widely used for hydraulic fluid transmissions.

PIX also manufactures Compact Hose which is smaller in diameter with higher performance characteristic. It operates at smaller bend radius (approximately 25% to 30% smaller), its specialty is that the lining and cover thickness is less as compared to the normal hydraulic hose with same working pressure rating. It is light in weight & its compactness also offers the advantage to use in application having minimum space available.

PIX - PERFORMER (Standards: EN 853 1SN, SAE 100 R1S-AT, ISO 1436)

Special Features: Qualified for double impulse cycles (300,000 cycles) to relevant standards- SAE 100 R1S AT / EN 853 1SN / ISO 1436-1SN. Highly flexible. Light weight. Easy to Handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min. Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE105 -3 5 3/16 4.8 9.5 11.5 25.0 250 3625 100.0 1000 14500 90 0.150 PF 22 05

PE106 -4 6 1/4 6.4 11.1 13.2 22.5 225 3263 90.0 900 13050 100 0.190PF 22

06

PE108 -5 8 5/16 7.9 12.7 15.0 21.5 215 3118 86.0 860 12470 115 0.234PF 22

08

PE110 -6 10 3/8 9.5 15.1 17.3 18.0 180 2610 72.0 720 10440 125 0.298PF 22

10

PE112 -8 12 1/2 12.7 18.3 20.6 16.0 160 2320 64.0 640 9280 180 0.384PF 22

12

PE116 -10 16 5/8 15.9 21.4 23.9 13.0 130 1885 52.0 520 7540 205 0.502PF 22

16

PE119 -12 19 3/4 19.0 25.4 27.6 10.5 105 1523 42.0 420 6090 240 0.649PF 22

19

PE125 -16 25 1 25.4 33.3 35.3 9.0 90 1305 36.0 360 5220 300 0.870PF 22

25

PE131 -20 31 1-1/4 31.8 40.5 43.2 6.3 63 914 25.2 252 3654 420 1.155PF 22

31

PE138 -24 38 1-1/2 38.1 46.8 50.7 5.0 50 725 20.0 200 2900 500 1.477PF 22

38

PE151 -32 51 2 50.8 60.2 64.2 4.0 40 580 16.0 160 2320 630 2.135PF 22

51

* PE163-40 63 2-1/2 63.5 73.0 78.0 5.0 50 725 20.0 200 2900 760 2.875 * *

* PE176-48 76 3 76.2 86.0 91.0 3.5 35 508 14.0 140 2030 900 3.320 * *

* PE1102-64 102 4 101.6 111.0 116.0 2.5 25 363 10.0 100 1450 1250 4.010 * *

* PIX Proprietary

Application: Medium to high pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

PIX - PERFORMER (Standards: EN 853 2SN, SAE 100 R2S-AT, ISO 1436)

Special Features: Qualified for double impulse cycles (400,000 cycles) to relevant standards- SAE 100 R2S AT / EN 853 2SN / ISO 1436-2SN. Highly flexible Ligh weight. Easy to handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE205-3 5 3/16 4.8 11.0 12.8 45.0 450 6525 180.0 1800 26100 90 0.310

PF 2205

PE206-4 6 1/4 6.4 12.7 14.9 40.0 400 5800 160.0 1600 23200 100 0.368

PF 2206

PE208-5 8 5/16 7.9 14.3 16.7 35.0 350 5000 140.0 1400 20000 115 0.431

PF 2208

PE210-6 10 3/8 9.5 16.7 19.1 33.0 330 4785 132.0 1320 19140 125 0.532

PF 2210

PE212-8 12 1/2 12.7 19.8 22.1 27.5 275 3988 110.0 1100 15950 180 0.629

PF 2212

PE216-10 16 5/8 15.9 23.0 25.3 25.0 250 3625 100.0 1000 14500 205 0.772

PF 2216

PE219-12 19 3/4 19.0 27.0 29.6 21.5 215 3118 86.0 860 12470 240 0.920

PF 2219

PE225-16 25 1 25.4 35.1 37.7 16.5 165 2393 66.0 660 9570 300 1.271

PF 2225

PE231-20 31 1-1/4 31.8 44.7 47.7 12.5 125 1813 50.0 500 7250 420 1.961

PF 2231

PE238-24 38 1-1/2 38.1 50.8 54.0 9.0 90 1305 36.0 360 5220 500 2.211

PF 2238

PE251-32 51 2 50.8 63.3 67.5 8.0 80 1160 32.0 320 4640 630 3.225

PF 2251

*PE263-40 63 2-1/2 63.5 75.0 80.0 7.0 70 1000 28.0 280 4000 760 3.710 * *

*PE276-48 76 3 76.2 88.0 93.0 5.5 55 798 22.0 220 3190 900 4.390 * *

*PE2102-64 102 4 101.6 113.0 118.0 4.0 40 580 16.0 160 2320 1250 5.300 * *

* PIX Proprietary

Application: Medium to high pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

Working Temperature: - 40ºC to + 100ºC (Continuous). Intermittent Temperature: - 40ºC to + 120ºC (10% of total working hours)

For air application (Temp. max 70ºC) & pressure above 17 bar cover must be pin pricked. Special MSHA approved flame resistant outer cover can be provided on request.

Note: ** For "Recommended Ferrule" code details, please e-mail us at techsupport@pixtrans.com.

PIX - PERFORMER (Standards: SAE J517 100 R5R, Rubber Cover)

Special Features: Qualified for double (300,000) impulse cycles up to size 7/8" and (200,000) impulse cycles for 1-1/8" to relevant SAE 100R5 standard. Good flexibility. Thicker cover for very good abrasion resistance and weather protection.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE106R5R -5 6 1/4 6.4 12.3 14.8 21.0 210 3000 84.0 840 12000 85 0.240PF 11

06

PE108R5R -6 8 5/16 7.9 14.0 17.3 15.7 157 2277 62.8 628 9106 100 0.320PF 11

08

PE110R5R -8 10 13/32 10.3 16.0 19.4 14.0 140 2000 56.0 560 8000 115 0.360PF 11

10

PE112R5R -10 12 1/2 12.7 18.0 23.4 12.2 122 1769 48.8 488 7076 140 0.490PF 11

12

PE116R5R -12 16 5/8 15.9 22.0 27.4 10.5 105 1523 42.0 420 6090 165 0.630PF 11

16

PE122R5R -16 22 7/8 22.2 28.0 31.4 5.6 56 812 22.4 224 3248 185 0.690PF 11

22

PE128R5R -20 28 1-1/8 28.5 35.0 37.6 4.3 43 624 17.2 172 2494 230 0.810PF 11

28

Application: Medium pressure hydraulic application. Suitable for hydraulic oils, air, gasoline, crude oil & lubricating oils. Hydraulic power-pack return lines.

PIX - PERFORMER / T (Standards: EN 853 1ST, ISO 1436)

Special Features: Qualified for double impulse cycles (300,000 cycles) to relevant standards-EN 853 1ST / ISO 1436-1ST. Thicker cover for very good abrasion resistance and weather protection. Highly flexible, light weight, easy

to handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE106 -4 6 1/4 6.4 11.1 15.5 22.5 225 3263 90.0 900 13050 100 0.260PF 11

06

PE108 -5 8 5/16 7.9 12.7 17.1 21.5 215 3118 86.0 860 12470 115 0.305PF 11

08

PE110 -6 10 3/8 9.5 15.1 19.8 18.0 180 2610 72.0 720 10440 125 0.396PF 11

10

PE112 -8 12 1/2 12.7 18.3 22.6 16.0 160 2320 64.0 640 9280 180 0.475PF 11

12

PE116 -10 16 5/8 15.9 21.4 26.0 13.0 130 1885 52.0 520 7540 205 0.613PF 11

16

PE119 -12 19 3/4 19.0 25.4 29.8 10.5 105 1523 42.0 420 6090 240 0.783PF 11

19

PE125 -16 25 1 25.4 33.3 37.5 9.0 90 1305 36.0 360 5220 300 1.058PF 11

25

PE131 -20 31 1-1/4 31.8 40.5 45.5 6.3 63 914 25.0 250 3654 420 1.410PF 11

31

PE138 -24 38 1-1/2 38.1 46.8 52.4 5.0 50 725 20.0 200 2900 500 1.860PF 11

38

PE151 -32 51 2 50.8 60.2 66.3 4.0 40 580 16.0 160 2320 630 2.470PF 11

51

Application: Medium to high pressure hydraulic lines where self abrasion and inter substrate abrasion is foreseen. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

PERFORMER / T 100R2A (Standards: EN 853 2ST, ISO 1436)

Special Features: Qualified for double impulse cycles (400,000 cycles) to relevant standards EN 853 2ST /ISO 1436 - 2ST. Thicker cover for very good abrasion resistance and weather protection. Highly flexible, light wight, easy to handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Mini.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE206 -4 6 1/4 6.4 12.7 17.0 40.0 400 5800 160.0 1600 23200 100 0.445PF 12

06

PE208 -5 8 5/16 7.9 14.3 18.8 35.0 350 5000 140.0 1400 20000 115 0.518PF 12

08

PE210 -6 10 3/8 9.5 16.7 21.1 33.0 330 4785 132.0 1320 19140 125 0.626PF 12

10

PE212 -8 12 1/2 12.7 19.8 24.1 27.5 275 3988 110.0 1100 15950 180 0.732PF 12

12

PE216 -10 16 5/8 15.9 23.0 27.4 25.0 250 3625 100.0 1000 14500 205 0.876PF 12

16

PE219 -12 19 3/4 19.0 27.0 31.2 21.5 215 3118 86.0 860 12470 240 1.160PF 12

19

PE225 -16 25 1 25.4 35.1 39.0 16.5 165 2393 66.0 660 9570 300 1.377PF 12

25

PE231 -20 31 1-1/4 31.8 45.0 50.6 12.5 125 1813 50.0 500 7250 420 2.266PF 12

31

PE238 -24 38 1-1/2 38.1 50.8 57.2 9.0 90 1305 36.0 360 5220 500 2.604PF 12

38

PE251 -32 51 2 50.8 63.3 68.4 8.0 80 1160 32.0 320 4640 630 3.384PF 12

51

PE2102 -64 102 4 101.6 113.0 120.0 4.0 40 580 16.0 160 2320 1250 5.800 * *

Application: Medium to high pressure hydraulic lines where self abrasion and inter substrate abrasion is foreseen. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

Working temperature: -40ºC To +100ºC (Continuous)Intermittent temperature: -40ºC to +120ºC (10% of total working hours)For air application (Temp. Max 70ºC) & pressure above 17 bar cover must be pin prickedSpecial MSHA approved flame resistant outer cover can be provided on request.

MPa bar psi MPa bar psi mm

PE106R5R -5 6 1/4 6.4 12.3 14.8 21.0 210 3000 84.0 840 12000 85 0.240PF 1106

PE108R5R -6 8 5/16 7.9 14.0 17.3 15.7 157 2277 62.8 628 9106 100 0.320PF 1108

PE110R5R -8 10 13/32 10.3 16.0 19.4 14.0 140 2000 56.0 560 8000 115 0.360PF 1110

PE112R5R -10 12 1/2 12.7 18.0 23.4 12.2 122 1769 48.8 488 7076 140 0.490PF 1112

PE116R5R -12 16 5/8 15.9 22.0 27.4 10.5 105 1523 42.0 420 6090 165 0.630PF 1116

PE122R5R -16 22 7/8 22.2 28.0 31.4 5.6 56 812 22.4 224 3248 185 0.690PF 1122

PE128R5R -20 28 1-1/8 28.5 35.0 37.6 4.3 43 624 17.2 172 2494 230 0.810PF 1128

Application: Medium pressure hydraulic application. Suitable for hydraulic oils, air, gasoline, crude oil & lubricating oils. Hydraulic power-pack return lines.

PIX - PERFORMER / T (Standards: EN 853 1ST, ISO 1436)

Special Features: Qualified for double impulse cycles (300,000 cycles) to relevant standards-EN 853 1ST / ISO 1436-1ST. Thicker cover for very good abrasion resistance and weather protection. Highly flexible, light weight, easy to handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE106 -4 6 1/4 6.4 11.1 15.5 22.5 225 3263 90.0 900 13050 100 0.260PF 11

06

PE108 -5 8 5/16 7.9 12.7 17.1 21.5 215 3118 86.0 860 12470 115 0.305PF 11

08

PE110 -6 10 3/8 9.5 15.1 19.8 18.0 180 2610 72.0 720 10440 125 0.396PF 11

10

PE112 -8 12 1/2 12.7 18.3 22.6 16.0 160 2320 64.0 640 9280 180 0.475PF 11

12

PE116 -10 16 5/8 15.9 21.4 26.0 13.0 130 1885 52.0 520 7540 205 0.613PF 11

16

PE119 -12 19 3/4 19.0 25.4 29.8 10.5 105 1523 42.0 420 6090 240 0.783PF 11

19

PE125 -16 25 1 25.4 33.3 37.5 9.0 90 1305 36.0 360 5220 300 1.058PF 11

25

PE131 -20 31 1-1/4 31.8 40.5 45.5 6.3 63 914 25.0 250 3654 420 1.410PF 11

31

PE138 -24 38 1-1/2 38.1 46.8 52.4 5.0 50 725 20.0 200 2900 500 1.860PF 11

38

PE151 -32 51 2 50.8 60.2 66.3 4.0 40 580 16.0 160 2320 630 2.470PF 11

51

Application: Medium to high pressure hydraulic lines where self abrasion and inter substrate abrasion is foreseen. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

PERFORMER / T 100R2A (Standards: EN 853 2ST, ISO 1436)

Special Features: Qualified for double impulse cycles (400,000 cycles) to relevant standards EN 853 2ST /ISO 1436 - 2ST. Thicker cover for very good abrasion resistance and weather protection. Highly flexible, light wight, easy to handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Mini.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE206 -4 6 1/4 6.4 12.7 17.0 40.0 400 5800 160.0 1600 23200 100 0.445PF 12

06

PE208 -5 8 5/16 7.9 14.3 18.8 35.0 350 5000 140.0 1400 20000 115 0.518PF 12

08

PE210 -6 10 3/8 9.5 16.7 21.1 33.0 330 4785 132.0 1320 19140 125 0.626PF 12

10

PE212 -8 12 1/2 12.7 19.8 24.1 27.5 275 3988 110.0 1100 15950 180 0.732PF 12

12

PE216 -10 16 5/8 15.9 23.0 27.4 25.0 250 3625 100.0 1000 14500 205 0.876PF 12

16

PE219 -12 19 3/4 19.0 27.0 31.2 21.5 215 3118 86.0 860 12470 240 1.160PF 12

19

PE225 -16 25 1 25.4 35.1 39.0 16.5 165 2393 66.0 660 9570 300 1.377PF 12

25

PE231 -20 31 1-1/4 31.8 45.0 50.6 12.5 125 1813 50.0 500 7250 420 2.266PF 12

31

PE238 -24 38 1-1/2 38.1 50.8 57.2 9.0 90 1305 36.0 360 5220 500 2.604PF 12

38

PE251 -32 51 2 50.8 63.3 68.4 8.0 80 1160 32.0 320 4640 630 3.384PF 12

51

PE2102 -64 102 4 101.6 113.0 120.0 4.0 40 580 16.0 160 2320 1250 5.800 * *

Application: Medium to high pressure hydraulic lines where self abrasion and inter substrate abrasion is foreseen. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

Working temperature: -40ºC To +100ºC (Continuous)Intermittent temperature: -40ºC to +120ºC (10% of total working hours)For air application (Temp. Max 70ºC) & pressure above 17 bar cover must be pin prickedSpecial MSHA approved flame resistant outer cover can be provided on request.

PIX_Hydraulic_Hoses / PIX_Performer_Hoses

PIX Hydraulic Hose is useful for medium pressure service with high petroleum base hydraulic fluids, carrying hot oils, grease, lubricants, Crude oil, fuel oil and water. It is widely used for hydraulic fluid transmissions.

PIX also manufactures Compact Hose which is smaller in diameter with higher performance characteristic. It operates at smaller bend radius (approximately 25% to 30% smaller), its specialty is that the lining and cover thickness is less as compared to the normal hydraulic hose with same working pressure rating. It is light in weight & its compactness also offers the advantage to use in application having minimum space available.

PIX - PERFORMER (Standards: EN 853 1SN, SAE 100 R1S-AT, ISO 1436)

Special Features: Qualified for double impulse cycles (300,000 cycles) to relevant standards- SAE 100 R1S AT / EN 853 1SN / ISO 1436-1SN. Highly flexible. Light weight. Easy to Handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min. Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE105 -3 5 3/16 4.8 9.5 11.5 25.0 250 3625 100.0 1000 14500 90 0.150 PF 22 05

PE106 -4 6 1/4 6.4 11.1 13.2 22.5 225 3263 90.0 900 13050 100 0.190PF 22

06

PE108 -5 8 5/16 7.9 12.7 15.0 21.5 215 3118 86.0 860 12470 115 0.234PF 22

08

PE110 -6 10 3/8 9.5 15.1 17.3 18.0 180 2610 72.0 720 10440 125 0.298PF 22

10

PE112 -8 12 1/2 12.7 18.3 20.6 16.0 160 2320 64.0 640 9280 180 0.384PF 22

12

PE116 -10 16 5/8 15.9 21.4 23.9 13.0 130 1885 52.0 520 7540 205 0.502PF 22

16

PE119 -12 19 3/4 19.0 25.4 27.6 10.5 105 1523 42.0 420 6090 240 0.649PF 22

19

PE125 -16 25 1 25.4 33.3 35.3 9.0 90 1305 36.0 360 5220 300 0.870PF 22

25

PE131 -20 31 1-1/4 31.8 40.5 43.2 6.3 63 914 25.2 252 3654 420 1.155PF 22

31

PE138 -24 38 1-1/2 38.1 46.8 50.7 5.0 50 725 20.0 200 2900 500 1.477PF 22

38

PE151 -32 51 2 50.8 60.2 64.2 4.0 40 580 16.0 160 2320 630 2.135PF 22

51

* PE163-40 63 2-1/2 63.5 73.0 78.0 5.0 50 725 20.0 200 2900 760 2.875 * *

* PE176-48 76 3 76.2 86.0 91.0 3.5 35 508 14.0 140 2030 900 3.320 * *

* PE1102-64 102 4 101.6 111.0 116.0 2.5 25 363 10.0 100 1450 1250 4.010 * *

* PIX Proprietary

Application: Medium to high pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

PIX - PERFORMER (Standards: EN 853 2SN, SAE 100 R2S-AT, ISO 1436)

Special Features: Qualified for double impulse cycles (400,000 cycles) to relevant standards- SAE 100 R2S AT / EN 853 2SN / ISO 1436-2SN. Highly flexible Ligh weight. Easy to handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE205-3 5 3/16 4.8 11.0 12.8 45.0 450 6525 180.0 1800 26100 90 0.310

PF 2205

PE206-4 6 1/4 6.4 12.7 14.9 40.0 400 5800 160.0 1600 23200 100 0.368

PF 2206

PE208-5 8 5/16 7.9 14.3 16.7 35.0 350 5000 140.0 1400 20000 115 0.431

PF 2208

PE210-6 10 3/8 9.5 16.7 19.1 33.0 330 4785 132.0 1320 19140 125 0.532

PF 2210

PE212-8 12 1/2 12.7 19.8 22.1 27.5 275 3988 110.0 1100 15950 180 0.629

PF 2212

PE216-10 16 5/8 15.9 23.0 25.3 25.0 250 3625 100.0 1000 14500 205 0.772

PF 2216

PE219-12 19 3/4 19.0 27.0 29.6 21.5 215 3118 86.0 860 12470 240 0.920

PF 2219

PE225-16 25 1 25.4 35.1 37.7 16.5 165 2393 66.0 660 9570 300 1.271

PF 2225

PE231-20 31 1-1/4 31.8 44.7 47.7 12.5 125 1813 50.0 500 7250 420 1.961

PF 2231

PE238-24 38 1-1/2 38.1 50.8 54.0 9.0 90 1305 36.0 360 5220 500 2.211

PF 2238

PE251-32 51 2 50.8 63.3 67.5 8.0 80 1160 32.0 320 4640 630 3.225

PF 2251

*PE263-40 63 2-1/2 63.5 75.0 80.0 7.0 70 1000 28.0 280 4000 760 3.710 * *

*PE276-48 76 3 76.2 88.0 93.0 5.5 55 798 22.0 220 3190 900 4.390 * *

*PE2102-64 102 4 101.6 113.0 118.0 4.0 40 580 16.0 160 2320 1250 5.300 * *

* PIX Proprietary

Application: Medium to high pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

Working Temperature: - 40ºC to + 100ºC (Continuous). Intermittent Temperature: - 40ºC to + 120ºC (10% of total working hours)

For air application (Temp. max 70ºC) & pressure above 17 bar cover must be pin pricked. Special MSHA approved

flame resistant outer cover can be provided on request.

Note: ** For "Recommended Ferrule" code details, please e-mail us at techsupport@pixtrans.com.

PIX - PERFORMER (Standards: SAE J517 100 R5R, Rubber Cover)

Special Features: Qualified for double (300,000) impulse cycles up to size 7/8" and (200,000) impulse cycles for 1-1/8" to relevant SAE 100R5 standard. Good flexibility. Thicker cover for very good abrasion resistance and weather protection.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE106R5R -5 6 1/4 6.4 12.3 14.8 21.0 210 3000 84.0 840 12000 85 0.240PF 11

06

PE108R5R -6 8 5/16 7.9 14.0 17.3 15.7 157 2277 62.8 628 9106 100 0.320PF 11

08

PE110R5R -8 10 13/32 10.3 16.0 19.4 14.0 140 2000 56.0 560 8000 115 0.360PF 11

10

PE112R5R -10 12 1/2 12.7 18.0 23.4 12.2 122 1769 48.8 488 7076 140 0.490PF 11

12

PE116R5R -12 16 5/8 15.9 22.0 27.4 10.5 105 1523 42.0 420 6090 165 0.630PF 11

16

PE122R5R -16 22 7/8 22.2 28.0 31.4 5.6 56 812 22.4 224 3248 185 0.690PF 11

22

PE128R5R -20 28 1-1/8 28.5 35.0 37.6 4.3 43 624 17.2 172 2494 230 0.810PF 11

28

Application: Medium pressure hydraulic application. Suitable for hydraulic oils, air, gasoline, crude oil & lubricating oils. Hydraulic power-pack return lines.

PIX - PERFORMER / T (Standards: EN 853 1ST, ISO 1436)

Special Features: Qualified for double impulse cycles (300,000 cycles) to relevant standards-EN 853 1ST / ISO 1436-1ST. Thicker cover for very good abrasion resistance and weather protection. Highly flexible, light weight, easy to handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE106 -4 6 1/4 6.4 11.1 15.5 22.5 225 3263 90.0 900 13050 100 0.260PF 11

06

PE108 -5 8 5/16 7.9 12.7 17.1 21.5 215 3118 86.0 860 12470 115 0.305PF 11

08

PE110 -6 10 3/8 9.5 15.1 19.8 18.0 180 2610 72.0 720 10440 125 0.396PF 11

10

PE112 -8 12 1/2 12.7 18.3 22.6 16.0 160 2320 64.0 640 9280 180 0.475PF 11

12

PE116 -10 16 5/8 15.9 21.4 26.0 13.0 130 1885 52.0 520 7540 205 0.613PF 11

16

PE119 -12 19 3/4 19.0 25.4 29.8 10.5 105 1523 42.0 420 6090 240 0.783PF 11

19

PE125 -16 25 1 25.4 33.3 37.5 9.0 90 1305 36.0 360 5220 300 1.058PF 11

25

PE131 -20 31 1-1/4 31.8 40.5 45.5 6.3 63 914 25.0 250 3654 420 1.410PF 11

31

PE138 -24 38 1-1/2 38.1 46.8 52.4 5.0 50 725 20.0 200 2900 500 1.860PF 11

38

PE151 -32 51 2 50.8 60.2 66.3 4.0 40 580 16.0 160 2320 630 2.470PF 11

51

Application: Medium to high pressure hydraulic lines where self abrasion and inter substrate abrasion is foreseen. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

PERFORMER / T 100R2A (Standards: EN 853 2ST, ISO 1436)

Special Features: Qualified for double impulse cycles (400,000 cycles) to relevant standards EN 853 2ST /ISO 1436 - 2ST. Thicker cover for very good abrasion resistance and weather protection. Highly flexible, light wight, easy to handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Mini.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE206 -4 6 1/4 6.4 12.7 17.0 40.0 400 5800 160.0 1600 23200 100 0.445PF 12

06

PE208 -5 8 5/16 7.9 14.3 18.8 35.0 350 5000 140.0 1400 20000 115 0.518PF 12

08

PE210 -6 10 3/8 9.5 16.7 21.1 33.0 330 4785 132.0 1320 19140 125 0.626PF 12

10

PE212 -8 12 1/2 12.7 19.8 24.1 27.5 275 3988 110.0 1100 15950 180 0.732PF 12

12

PE216 -10 16 5/8 15.9 23.0 27.4 25.0 250 3625 100.0 1000 14500 205 0.876PF 12

16

PE219 -12 19 3/4 19.0 27.0 31.2 21.5 215 3118 86.0 860 12470 240 1.160PF 12

19

PE225 -16 25 1 25.4 35.1 39.0 16.5 165 2393 66.0 660 9570 300 1.377PF 12

25

PE231 -20 31 1-1/4 31.8 45.0 50.6 12.5 125 1813 50.0 500 7250 420 2.266PF 12

31

PE238 -24 38 1-1/2 38.1 50.8 57.2 9.0 90 1305 36.0 360 5220 500 2.604PF 12

38

PE251 -32 51 2 50.8 63.3 68.4 8.0 80 1160 32.0 320 4640 630 3.384PF 12

51

PE2102 -64 102 4 101.6 113.0 120.0 4.0 40 580 16.0 160 2320 1250 5.800 * *

Application: Medium to high pressure hydraulic lines where self abrasion and inter substrate abrasion is foreseen. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

Working temperature: -40ºC To +100ºC (Continuous)Intermittent temperature: -40ºC to +120ºC (10% of total working hours)For air application (Temp. Max 70ºC) & pressure above 17 bar cover must be pin prickedSpecial MSHA approved flame resistant outer cover can be provided on request.

PIX_Hydraulic_Hoses / PIX_Performer_Hoses

PIX Hydraulic Hose is useful for medium pressure service with high petroleum base hydraulic fluids, carrying hot oils, grease, lubricants, Crude oil, fuel oil and water. It is widely used for hydraulic fluid transmissions.

PIX also manufactures Compact Hose which is smaller in diameter with higher performance characteristic. It operates at smaller bend radius (approximately 25% to 30% smaller), its specialty is that the lining and cover thickness is less as compared to the normal hydraulic hose with same working pressure rating. It is light in weight & its compactness also offers the advantage to use in application having minimum space available.

PIX - PERFORMER (Standards: EN 853 1SN, SAE 100 R1S-AT, ISO 1436)

Special Features: Qualified for double impulse cycles (300,000 cycles) to relevant standards- SAE 100 R1S AT / EN 853 1SN / ISO 1436-1SN. Highly flexible. Light weight. Easy to Handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min. Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE105 -3 5 3/16 4.8 9.5 11.5 25.0 250 3625 100.0 1000 14500 90 0.150 PF 22 05

PE106 -4 6 1/4 6.4 11.1 13.2 22.5 225 3263 90.0 900 13050 100 0.190PF 22

06

PE108 -5 8 5/16 7.9 12.7 15.0 21.5 215 3118 86.0 860 12470 115 0.234PF 22

08

PE110 -6 10 3/8 9.5 15.1 17.3 18.0 180 2610 72.0 720 10440 125 0.298PF 22

10

PE112 -8 12 1/2 12.7 18.3 20.6 16.0 160 2320 64.0 640 9280 180 0.384PF 22

12

PE116 -10 16 5/8 15.9 21.4 23.9 13.0 130 1885 52.0 520 7540 205 0.502PF 22

16

PE119 -12 19 3/4 19.0 25.4 27.6 10.5 105 1523 42.0 420 6090 240 0.649PF 22

19

PE125 -16 25 1 25.4 33.3 35.3 9.0 90 1305 36.0 360 5220 300 0.870PF 22

25

PE131 -20 31 1-1/4 31.8 40.5 43.2 6.3 63 914 25.2 252 3654 420 1.155PF 22

31

PE138 -24 38 1-1/2 38.1 46.8 50.7 5.0 50 725 20.0 200 2900 500 1.477PF 22

38

PE151 -32 51 2 50.8 60.2 64.2 4.0 40 580 16.0 160 2320 630 2.135PF 22

51

* PE163-40 63 2-1/2 63.5 73.0 78.0 5.0 50 725 20.0 200 2900 760 2.875 * *

* PE176-48 76 3 76.2 86.0 91.0 3.5 35 508 14.0 140 2030 900 3.320 * *

* PE1102-64 102 4 101.6 111.0 116.0 2.5 25 363 10.0 100 1450 1250 4.010 * *

* PIX Proprietary

Application: Medium to high pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

PIX - PERFORMER (Standards: EN 853 2SN, SAE 100 R2S-AT, ISO 1436)

Special Features: Qualified for double impulse cycles (400,000 cycles) to relevant standards- SAE 100 R2S AT / EN 853 2SN / ISO 1436-2SN. Highly flexible Ligh weight. Easy to handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE205-3 5 3/16 4.8 11.0 12.8 45.0 450 6525 180.0 1800 26100 90 0.310

PF 2205

PE206-4 6 1/4 6.4 12.7 14.9 40.0 400 5800 160.0 1600 23200 100 0.368

PF 2206

PE208-5 8 5/16 7.9 14.3 16.7 35.0 350 5000 140.0 1400 20000 115 0.431

PF 2208

PE210-6 10 3/8 9.5 16.7 19.1 33.0 330 4785 132.0 1320 19140 125 0.532

PF 2210

PE212-8 12 1/2 12.7 19.8 22.1 27.5 275 3988 110.0 1100 15950 180 0.629

PF 2212

PE216-10 16 5/8 15.9 23.0 25.3 25.0 250 3625 100.0 1000 14500 205 0.772

PF 2216

PE219-12 19 3/4 19.0 27.0 29.6 21.5 215 3118 86.0 860 12470 240 0.920

PF 2219

PE225-16 25 1 25.4 35.1 37.7 16.5 165 2393 66.0 660 9570 300 1.271

PF 2225

PE231-20 31 1-1/4 31.8 44.7 47.7 12.5 125 1813 50.0 500 7250 420 1.961

PF 2231

PE238-24 38 1-1/2 38.1 50.8 54.0 9.0 90 1305 36.0 360 5220 500 2.211

PF 2238

PE251-32 51 2 50.8 63.3 67.5 8.0 80 1160 32.0 320 4640 630 3.225

PF 2251

*PE263-40 63 2-1/2 63.5 75.0 80.0 7.0 70 1000 28.0 280 4000 760 3.710 * *

*PE276-48 76 3 76.2 88.0 93.0 5.5 55 798 22.0 220 3190 900 4.390 * *

*PE2102-64 102 4 101.6 113.0 118.0 4.0 40 580 16.0 160 2320 1250 5.300 * *

* PIX Proprietary

Application: Medium to high pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

Working Temperature: - 40ºC to + 100ºC (Continuous). Intermittent Temperature: - 40ºC to + 120ºC (10% of total working hours)

For air application (Temp. max 70ºC) & pressure above 17 bar cover must be pin pricked. Special MSHA approved

flame resistant outer cover can be provided on request.

Note: ** For "Recommended Ferrule" code details, please e-mail us at techsupport@pixtrans.com.

PIX - PERFORMER (Standards: SAE J517 100 R5R, Rubber Cover)

Special Features: Qualified for double (300,000) impulse cycles up to size 7/8" and (200,000) impulse cycles for 1-1/8" to relevant SAE 100R5 standard. Good flexibility. Thicker cover for very good abrasion resistance and weather protection.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE106R5R -5 6 1/4 6.4 12.3 14.8 21.0 210 3000 84.0 840 12000 85 0.240PF 11

06

PE108R5R -6 8 5/16 7.9 14.0 17.3 15.7 157 2277 62.8 628 9106 100 0.320PF 11

08

PE110R5R -8 10 13/32 10.3 16.0 19.4 14.0 140 2000 56.0 560 8000 115 0.360PF 11

10

PE112R5R -10 12 1/2 12.7 18.0 23.4 12.2 122 1769 48.8 488 7076 140 0.490PF 11

12

PE116R5R -12 16 5/8 15.9 22.0 27.4 10.5 105 1523 42.0 420 6090 165 0.630PF 11

16

PE122R5R -16 22 7/8 22.2 28.0 31.4 5.6 56 812 22.4 224 3248 185 0.690PF 11

22

PE128R5R -20 28 1-1/8 28.5 35.0 37.6 4.3 43 624 17.2 172 2494 230 0.810PF 11

28

Application: Medium pressure hydraulic application. Suitable for hydraulic oils, air, gasoline, crude oil & lubricating oils. Hydraulic power-pack return lines.

PIX - PERFORMER / T (Standards: EN 853 1ST, ISO 1436)

Special Features: Qualified for double impulse cycles (300,000 cycles) to relevant standards-EN 853 1ST / ISO 1436-1ST. Thicker cover for very good abrasion resistance and weather protection. Highly flexible, light weight, easy to handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE106 -4 6 1/4 6.4 11.1 15.5 22.5 225 3263 90.0 900 13050 100 0.260PF 11

06

PE108 -5 8 5/16 7.9 12.7 17.1 21.5 215 3118 86.0 860 12470 115 0.305PF 11

08

PE110 -6 10 3/8 9.5 15.1 19.8 18.0 180 2610 72.0 720 10440 125 0.396PF 11

10

PE112 -8 12 1/2 12.7 18.3 22.6 16.0 160 2320 64.0 640 9280 180 0.475PF 11

12

PE116 -10 16 5/8 15.9 21.4 26.0 13.0 130 1885 52.0 520 7540 205 0.613PF 11

16

PE119 -12 19 3/4 19.0 25.4 29.8 10.5 105 1523 42.0 420 6090 240 0.783PF 11

19

PE125 -16 25 1 25.4 33.3 37.5 9.0 90 1305 36.0 360 5220 300 1.058PF 11

25

PE131 -20 31 1-1/4 31.8 40.5 45.5 6.3 63 914 25.0 250 3654 420 1.410PF 11

31

PE138 -24 38 1-1/2 38.1 46.8 52.4 5.0 50 725 20.0 200 2900 500 1.860PF 11

38

PE151 -32 51 2 50.8 60.2 66.3 4.0 40 580 16.0 160 2320 630 2.470PF 11

51

Application: Medium to high pressure hydraulic lines where self abrasion and inter substrate abrasion is foreseen. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

PERFORMER / T 100R2A (Standards: EN 853 2ST, ISO 1436)

Special Features: Qualified for double impulse cycles (400,000 cycles) to relevant standards EN 853 2ST /ISO 1436 - 2ST. Thicker cover for very good abrasion resistance and weather protection. Highly flexible, light wight, easy to handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Mini.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE206 -4 6 1/4 6.4 12.7 17.0 40.0 400 5800 160.0 1600 23200 100 0.445PF 12

06

PE208 -5 8 5/16 7.9 14.3 18.8 35.0 350 5000 140.0 1400 20000 115 0.518PF 12

08

PE210 -6 10 3/8 9.5 16.7 21.1 33.0 330 4785 132.0 1320 19140 125 0.626PF 12

10

PE212 -8 12 1/2 12.7 19.8 24.1 27.5 275 3988 110.0 1100 15950 180 0.732PF 12

12

PE216 -10 16 5/8 15.9 23.0 27.4 25.0 250 3625 100.0 1000 14500 205 0.876PF 12

16

PE219 -12 19 3/4 19.0 27.0 31.2 21.5 215 3118 86.0 860 12470 240 1.160PF 12

19

PE225 -16 25 1 25.4 35.1 39.0 16.5 165 2393 66.0 660 9570 300 1.377PF 12

25

PE231 -20 31 1-1/4 31.8 45.0 50.6 12.5 125 1813 50.0 500 7250 420 2.266PF 12

31

PE238 -24 38 1-1/2 38.1 50.8 57.2 9.0 90 1305 36.0 360 5220 500 2.604PF 12

38

PE251 -32 51 2 50.8 63.3 68.4 8.0 80 1160 32.0 320 4640 630 3.384PF 12

51

PE2102 -64 102 4 101.6 113.0 120.0 4.0 40 580 16.0 160 2320 1250 5.800 * *

Application: Medium to high pressure hydraulic lines where self abrasion and inter substrate abrasion is foreseen. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

Working temperature: -40ºC To +100ºC (Continuous)Intermittent temperature: -40ºC to +120ºC (10% of total working hours)For air application (Temp. Max 70ºC) & pressure above 17 bar cover must be pin prickedSpecial MSHA approved flame resistant outer cover can be provided on request.

PIX_Hydraulic_Hoses / PIX_Performer_Hoses

PIX Hydraulic Hose is useful for medium pressure service with high petroleum base hydraulic fluids, carrying hot oils, grease, lubricants, Crude oil, fuel oil and water. It is widely used for hydraulic fluid transmissions.

PIX also manufactures Compact Hose which is smaller in diameter with higher performance characteristic. It operates at smaller bend radius (approximately 25% to 30% smaller), its specialty is that the lining and cover thickness is less as compared to the normal hydraulic hose with same working pressure rating. It is light in weight & its compactness also offers the advantage to use in application having minimum space available.

PIX - PERFORMER (Standards: EN 853 1SN, SAE 100 R1S-AT, ISO 1436)

Special Features: Qualified for double impulse cycles (300,000 cycles) to relevant standards- SAE 100 R1S AT / EN 853 1SN / ISO 1436-1SN. Highly flexible. Light weight. Easy to Handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min. Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE105 -3 5 3/16 4.8 9.5 11.5 25.0 250 3625 100.0 1000 14500 90 0.150 PF 22 05

PE106 -4 6 1/4 6.4 11.1 13.2 22.5 225 3263 90.0 900 13050 100 0.190PF 22

06

PE108 -5 8 5/16 7.9 12.7 15.0 21.5 215 3118 86.0 860 12470 115 0.234PF 22

08

PE110 -6 10 3/8 9.5 15.1 17.3 18.0 180 2610 72.0 720 10440 125 0.298PF 22

10

PE112 -8 12 1/2 12.7 18.3 20.6 16.0 160 2320 64.0 640 9280 180 0.384PF 22

12

PE116 -10 16 5/8 15.9 21.4 23.9 13.0 130 1885 52.0 520 7540 205 0.502PF 22

16

PE119 -12 19 3/4 19.0 25.4 27.6 10.5 105 1523 42.0 420 6090 240 0.649PF 22

19

PE125 -16 25 1 25.4 33.3 35.3 9.0 90 1305 36.0 360 5220 300 0.870PF 22

25

PE131 -20 31 1-1/4 31.8 40.5 43.2 6.3 63 914 25.2 252 3654 420 1.155PF 22

31

PE138 -24 38 1-1/2 38.1 46.8 50.7 5.0 50 725 20.0 200 2900 500 1.477PF 22

38

PE151 -32 51 2 50.8 60.2 64.2 4.0 40 580 16.0 160 2320 630 2.135PF 22

51

* PE163-40 63 2-1/2 63.5 73.0 78.0 5.0 50 725 20.0 200 2900 760 2.875 * *

* PE176-48 76 3 76.2 86.0 91.0 3.5 35 508 14.0 140 2030 900 3.320 * *

* PE1102-64 102 4 101.6 111.0 116.0 2.5 25 363 10.0 100 1450 1250 4.010 * *

* PIX Proprietary

Application: Medium to high pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

PIX - PERFORMER (Standards: EN 853 2SN, SAE 100 R2S-AT, ISO 1436)

Special Features:

Qualified for double impulse cycles (400,000 cycles) to relevant standards- SAE 100 R2S AT / EN 853 2SN / ISO 1436-2SN. Highly flexible Ligh weight. Easy to handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE205-3 5 3/16 4.8 11.0 12.8 45.0 450 6525 180.0 1800 26100 90 0.310

PF 2205

PE206-4 6 1/4 6.4 12.7 14.9 40.0 400 5800 160.0 1600 23200 100 0.368

PF 2206

PE208-5 8 5/16 7.9 14.3 16.7 35.0 350 5000 140.0 1400 20000 115 0.431

PF 2208

PE210-6 10 3/8 9.5 16.7 19.1 33.0 330 4785 132.0 1320 19140 125 0.532

PF 2210

PE212-8 12 1/2 12.7 19.8 22.1 27.5 275 3988 110.0 1100 15950 180 0.629

PF 2212

PE216-10 16 5/8 15.9 23.0 25.3 25.0 250 3625 100.0 1000 14500 205 0.772

PF 2216

PE219-12 19 3/4 19.0 27.0 29.6 21.5 215 3118 86.0 860 12470 240 0.920

PF 2219

PE225-16 25 1 25.4 35.1 37.7 16.5 165 2393 66.0 660 9570 300 1.271

PF 2225

PE231-20 31 1-1/4 31.8 44.7 47.7 12.5 125 1813 50.0 500 7250 420 1.961

PF 2231

PE238-24 38 1-1/2 38.1 50.8 54.0 9.0 90 1305 36.0 360 5220 500 2.211

PF 2238

PE251-32 51 2 50.8 63.3 67.5 8.0 80 1160 32.0 320 4640 630 3.225

PF 2251

*PE263-40 63 2-1/2 63.5 75.0 80.0 7.0 70 1000 28.0 280 4000 760 3.710 * *

*PE276-48 76 3 76.2 88.0 93.0 5.5 55 798 22.0 220 3190 900 4.390 * *

*PE2102-64 102 4 101.6 113.0 118.0 4.0 40 580 16.0 160 2320 1250 5.300 * *

* PIX Proprietary

Application: Medium to high pressure hydraulic lines. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

Working Temperature: - 40ºC to + 100ºC (Continuous). Intermittent Temperature: - 40ºC to + 120ºC (10% of total working hours)

For air application (Temp. max 70ºC) & pressure above 17 bar cover must be pin pricked. Special MSHA approved flame resistant outer cover can be provided on request.

Note: ** For "Recommended Ferrule" code details, please e-mail us at techsupport@pixtrans.com.

PIX - PERFORMER (Standards: SAE J517 100 R5R, Rubber Cover)

Special Features: Qualified for double (300,000) impulse cycles up to size 7/8" and (200,000) impulse cycles for 1-1/8" to relevant SAE 100R5 standard. Good flexibility. Thicker cover for very good abrasion resistance and weather protection.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE106R5R -5 6 1/4 6.4 12.3 14.8 21.0 210 3000 84.0 840 12000 85 0.240PF 11

06

PE108R5R -6 8 5/16 7.9 14.0 17.3 15.7 157 2277 62.8 628 9106 100 0.320PF 11

08

PE110R5R -8 10 13/32 10.3 16.0 19.4 14.0 140 2000 56.0 560 8000 115 0.360PF 11

10

PE112R5R -10 12 1/2 12.7 18.0 23.4 12.2 122 1769 48.8 488 7076 140 0.490PF 11

12

PE116R5R -12 16 5/8 15.9 22.0 27.4 10.5 105 1523 42.0 420 6090 165 0.630PF 11

16

PE122R5R -16 22 7/8 22.2 28.0 31.4 5.6 56 812 22.4 224 3248 185 0.690PF 11

22

PE128R5R -20 28 1-1/8 28.5 35.0 37.6 4.3 43 624 17.2 172 2494 230 0.810PF 11

28

Application: Medium pressure hydraulic application. Suitable for hydraulic oils, air, gasoline, crude oil & lubricating oils. Hydraulic power-pack return lines.

PIX - PERFORMER / T (Standards: EN 853 1ST, ISO 1436)

Special Features: Qualified for double impulse cycles (300,000 cycles) to relevant standards-EN 853 1ST / ISO 1436-1ST. Thicker cover for very good abrasion resistance and weather protection. Highly flexible, light weight, easy to handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Min.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE106 -4 6 1/4 6.4 11.1 15.5 22.5 225 3263 90.0 900 13050 100 0.260PF 11

06

PE108 -5 8 5/16 7.9 12.7 17.1 21.5 215 3118 86.0 860 12470 115 0.305PF 11

08

PE110 -6 10 3/8 9.5 15.1 19.8 18.0 180 2610 72.0 720 10440 125 0.396PF 11

10

PE112 -8 12 1/2 12.7 18.3 22.6 16.0 160 2320 64.0 640 9280 180 0.475PF 11

12

PE116 -10 16 5/8 15.9 21.4 26.0 13.0 130 1885 52.0 520 7540 205 0.613PF 11

16

PE119 -12 19 3/4 19.0 25.4 29.8 10.5 105 1523 42.0 420 6090 240 0.783PF 11

19

PE125 -16 25 1 25.4 33.3 37.5 9.0 90 1305 36.0 360 5220 300 1.058PF 11

25

PE131 -20 31 1-1/4 31.8 40.5 45.5 6.3 63 914 25.0 250 3654 420 1.410PF 11

31

PE138 -24 38 1-1/2 38.1 46.8 52.4 5.0 50 725 20.0 200 2900 500 1.860PF 11

38

PE151 -32 51 2 50.8 60.2 66.3 4.0 40 580 16.0 160 2320 630 2.470PF 11

51

Application: Medium to high pressure hydraulic lines where self abrasion and inter substrate abrasion is foreseen. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

PERFORMER / T 100R2A (Standards: EN 853 2ST, ISO 1436)

Special Features: Qualified for double impulse cycles (400,000 cycles) to relevant standards EN 853 2ST /ISO 1436 - 2ST. Thicker cover for very good abrasion resistance and weather protection. Highly flexible, light wight, easy to handle and route.

Product Range:

ProductCode

Dash DNHose

ID(inch)

Hose ID

(mm)

Braid OD

(mm)

Hose OD

(mm)

Maximum WorkingPressure

Minimum BurstPressure

Mini.Bend

RadiusWeightMeter

Kgs/mtr

Recom.Ferrule

MPa bar psi MPa bar psi mm

PE206 -4 6 1/4 6.4 12.7 17.0 40.0 400 5800 160.0 1600 23200 100 0.445PF 12

06

PE208 -5 8 5/16 7.9 14.3 18.8 35.0 350 5000 140.0 1400 20000 115 0.518PF 12

08

PE210 -6 10 3/8 9.5 16.7 21.1 33.0 330 4785 132.0 1320 19140 125 0.626PF 12

10

PE212 -8 12 1/2 12.7 19.8 24.1 27.5 275 3988 110.0 1100 15950 180 0.732PF 12

12

PE216 -10 16 5/8 15.9 23.0 27.4 25.0 250 3625 100.0 1000 14500 205 0.876PF 12

16

PE219 -12 19 3/4 19.0 27.0 31.2 21.5 215 3118 86.0 860 12470 240 1.160PF 12

19

PE225 -16 25 1 25.4 35.1 39.0 16.5 165 2393 66.0 660 9570 300 1.377PF 12

25

PE231 -20 31 1-1/4 31.8 45.0 50.6 12.5 125 1813 50.0 500 7250 420 2.266PF 12

31

PE238 -24 38 1-1/2 38.1 50.8 57.2 9.0 90 1305 36.0 360 5220 500 2.604PF 12

38

PE251 -32 51 2 50.8 63.3 68.4 8.0 80 1160 32.0 320 4640 630 3.384PF 12

51

PE2102 -64 102 4 101.6 113.0 120.0 4.0 40 580 16.0 160 2320 1250 5.800 * *

Application: Medium to high pressure hydraulic lines where self abrasion and inter substrate abrasion is foreseen. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.

Working temperature: -40ºC To +100ºC (Continuous)Intermittent temperature: -40ºC to +120ºC (10% of total working hours)For air application (Temp. Max 70ºC) & pressure above 17 bar cover must be pin prickedSpecial MSHA approved flame resistant outer cover can be provided on request.