©2020 Shabby Fabrics

Recommended Products• Creative Grids 9in Seam Guide Tool (for first method)• Creative Grids 3½" × 3½" Ruler #CGR3 (for first method)• Star Singles 1½" Half Square Triangle Paper (for second method)• Neutral Piecing 3pc Thread Set• Creative Grids I Love My Quilting Friends Ruler 2½" × 6½"• Creative Grids 2½" × 24½" Ruler #CGR224• Schmetz Topstitch Needles, size 80/12• Clover Patchwork Pins (Extra Fine)

All available at

16" × 48½"

PINWHEEL STRIPE TABLE RUNNER

page 1 of 2

Cut FabricsFrom border stripe fabric, fussy cut:

• (2) 48½" × 53/4" strips, centered on coffee cupsFrom red dot fabric, cut:

• (3) 1½" × WOF strips Sew into one long strip, then subcut: (2) 1½" × 48½" strips for sashing

• (4) 2½" × WOF for binding

From cream words fabric, cut:• (32) 2½" × 2½" squares for pinwheels

OR if using 1½" Star Singles, (8) 5" × 5" squares From black coffee bean fabric, cut:

• (32) 2½" × 2½" squares for pinwheels OR if using 1½" Star Singles, (8) 5" × 5" squares

53/4"

53/4"

Follow along with theHow to Make aHow to Make a

Pinwheel StripePinwheel StripeTable RunnerTable Runner

video featured on our YouTube channel:

YouTube.com/Shabby Fabrics

KITS available at

(while supplies last)

©2020 Shabby Fabrics page 2 of 2

Assemble Table RunnerArrange Pinwheel Blocks in a row. Sew together, two at a time, pressing seams open. Join units into groups of four, then join groups together.

Finish Table RunnerLayer table runner, batting, and backing. Quilt as desired.Sew the binding strips into one long strip. Fold binding in half lengthwise with wrong sides together and press. Sew the binding to the front side of the table runner starting at any side. Turn the binding over the edge and machine stitch or hand sew to the back of the table runner.

STEP 6: Repeat Steps 1-5 to make two more HST. You will now have four HST. STEP 7: Lay them out and sew them together as shown, pressing seams open.IMPORTANT: Square each Pinwheel Block to 3½" × 3½". Repeat these steps to make a total of (16) Pinwheel Blocks.

Steps 6-7

Pinwheel Unit should measure 3½" × 48½".Add (1) sashing strip to the top of each border strip. Press seams toward border strip.Add (1) sashing/border strip unit to each side of the Pinwheel Unit. Press seams toward sashing/border strip unit.

Love this? Find more projects

at (while supplies last)

PinwheelsIf using Star Singles 11/2" Half Square Triangle Papers: use (8) papers, (8) cream squares, and (8) black squares; follow instructions included with papers to make a total of (64) Half Square Triangles, and proceed to STEP 7.

STEP 1: On the back of (1) cream square, draw a line diagonally from corner to corner. STEP 2: Layer this cream square and one black square, RST, making sure to line up the edges. STEP 3: Sew ¼" on both sides of the drawn line. STEP 4: Cut on the drawn line. Press toward black. STEP 5: You will now have two Half Square Triangles (HST), which should each measure just over 2" × 2" square.

Step 3Step 2Step 1 Step 4 Step 5