PINNACLE LATHEMTP105 MANUAL

LAGUNA TOOLS2072 Alton ParkwayIrvine, California 92606Ph: 800.234.1976www.lagunatools.com © 2018, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved.

3

Table of contents Safety Rules Warranty Noise emission Specification sheet Floor plan Receiving your machine Introduction to your machine Where to locate your machine Unpacking your machine Assembly and set up Maintenance Troubleshooting Electrical drawing Spare parts Exploded view drawings and parts lists

4

Safety Rules As with all machinery there are certain hazards involved with the operation and use. Using it with caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result. If you have any questions relative to the installation and operation, do not use the equipment until you have contacted your supplying distributor. Read carefully before operating the lathe.

1. Keep the working area clean and be sure adequate lighting is available.

2. Do not wear loose clothing, gloves, bracelets, necklaces or ornaments. Wear face, eye, respiratory and body protection devices as indicated for the operation or environment.

3. Be sure that the power is disconnected from the machine before tools are serviced or an attachment is to be fitted or removed.

4. Never leave the machine with the power on. 5. Do not use dull, gummy or cracked cutting tools. 6. Be sure that the keys and adjusting wrenches have been removed and

all the nuts and bolts are secured.

Limited Warranty

New machines and accessories sold by Laguna Tools carry a one-year warranty effective from the date of shipping. Machines sold through dealers must be registered with Laguna Tools within 30 days of purchase to be covered by this warranty. Laguna Tools guarantees all new machines and accessories sold to be free of manufacturers’ defective workmanship, parts and materials. We will repair or replace, without charge, any parts determined by Laguna Tools, Inc. to be a manufacturer’s defect. We require that the defective item/part be returned to Laguna Tools with the complaint. Any machines returned to Laguna Tools must be returned with packaging in the same manner in which it was received. If a part or blade is being returned it must have adequate packaging to ensure no damage is received during shipping. In the event the item/part is determined to be damaged due to lack of maintenance, cleaning or misuse/abuse, the customer will be responsible for the cost to replace the item/part, plus all related shipping charges. This limited warranty does not apply to natural disasters, acts of terrorism, normal wear and tear, product failure due to lack of maintenance or cleaning, damage caused by accident, neglect, lack of or inadequate dust collection, misuse/abuse or damage caused where repair or alterations have been made or attempted by others.

Laguna Tools, Inc. is not responsible for additional tools or modifications sold orperformed (other than from/by Laguna Tools, Inc.) on any Laguna Tools, Inc. machine. Warranty maybe voided upon the addition of such described tools and/or modifications, determined on a case-by-case basis.

Software purchased through Laguna Tools Inc. is not covered under this warranty and all technical support must be managed through the software provider. Software is non-refundable.

Normal user alignment, adjustment, tuning and machine settings are not covered bythis warranty. It is the responsibility of the user to understand basic machinery operation, settings and procedures and to properly maintain the equipment in accordance with the standards provided by the manufacturer.

Parts, under warranty, are shipped at Laguna Tools, Inc.’s cost either by commoncarrier, FEDEX ground service or a similar method. Technical support to install replacement parts is primarily provided by phone, fax, e-mail or Laguna Tools Customer Support Website. The labor required to install replacement parts is the responsibility of the user.

Laguna Tools is not responsible for damage or loss caused by a freight company orother circumstances not in our control. All claims for loss or damaged goods must benotified to Laguna Tools within twenty-four hours of delivery. Please contact our Customer Service Department for more information.

Only new machines sold to the original owner are covered by this warranty.For warranty repair information, call 1-800-332-4094.

6

Noise emission Notes concerning noise emission Given that there exists a relationship between noise level and exposure times, it is not precise enough to determine the need for supplementary precautions. The factors affecting the true level of exposure to operators are clearly the amount of time exposed, the characteristics of working environment other sources of dust and noise etc. For example, adjacent machines in other words the level of ambient noise. It is possible that exposure level limits will vary from country to country. Machine Specification Distance between centres 50” [1270mm] Distance between centres with extended bed Factory fitted option

70”* [1778mm] and 100”* [2540mm]

Distance between spindle centre and bed 12” [305mm] with a section that can be removed to allow 48”[1219mm] diameter bowels to be turned.

Distance between ground and spindle centre

45” [1150mm]

Weight 560 lb [254 kg] Tail Stock Body material Cast iron Ram [Quill] diameter 1 27/32” [47mm] Ram [Quill] travel 5 33/64” [140mm] Ram [Quill] lead screw ACME Ram [Quill] graduations 1/16” for full 5 33/64” travel Ram internal taper Morse taper 3 Hole diameter through ram 5/16” [8mm] diameter Head Stock Head stock material Cast iron Bearings 4 bearing spindle sealed for life Drive type Pulleys / V belt Spindle speed 0-3500 / 0-2820 / 0-1200 / 0-450 rpm Rotation Forward / reverse Motor 1 1/5 hp 1 phase 220V or 3 hp 3-phase

factory fitted option. All motors with internal overload protector

Micro switch on access door to pulleys Yes Internal taper Morse taper 3 Spindle thread 45mm x 4.5mm pitch Indexing head 24 positions Spindle lock Yes Tool rest Swing over tool rest base Swing over bed

8 15/32” [215mm] 12” [305mm]

7

Tool rest movement Along the bed, full bed length.

Adjustable from spindle centre out 13”[330mm].

Tool Rest 10” [254mm] long Tool rest support shaft diameter 1 ½” [38.1mm] Vertical movement 1” [25mm] either side of the lathe centre. Standard supplied accessories Tool Kit Yes Manual Yes Chisel holder Yes Tool rest 10” Bowl tool rest [48” 1219mm] Yes Tail stock live centre Yes Head stock drive centre Yes Knock out rod Yes Face plate 10”[254mm] Motor 1 1/2 hp 1 phase Variable speed control 1 phase in Yes Foot start / stop switch Yes Options Copy attachment 50” [1270 mm] 2 9/16” [65mm] depth of

cut Copy attachment 100 [2540 mm] 2 9/16” [65mm] depth of

cut Factory fitted option. Copy attachment rotating steady Spiral cutting attachment 3”[76mm],4”[102mm],6”[152mm],

8”[203mm], 12”[305mm], 16”[406mm] & 24”[610mm] pitches, both left & right hand.

8

Receiving your machine.

Note. It is probable that a third party will deliver your machine. Before you unpack your new machine you will need to first inspect the packing, invoice and shipping documents supplied by the driver. Insure that there is no visible damage to the packing or the machine. You need to do this prior to the driver leaving. All damage must be noted on the delivery documents and signed by you and the delivery driver. You must then contact the seller [Laguna Tools] as soon as practical. If damage if found after delivery, contact the seller as soon as practical. Note the packaging may vary from that shown below. Note. The machine that you receive may differ from the one described in this manual depending on the options that you have ordered. For example if you have ordered a center lathe it will not come with the copy attachment.

Packaged lathe

Floor plan

9

What you will receive with your machine

Bowl tool rest

Tool holder

Tool kit

Levelling screws

Rotating centre

Optional router bracket

Optional copy follower

Copy saddle stops

Drive centre

Faceplate

Knock out rod

Optional spiral router index plate

10

Tool rest

Optional copy attachment

Optional spiral cutting gears

11

Introduction to the Pinnacle C1 lathe This machine is designed to give you years of safe service. Read this owners manual in its entirety before assembly or use. General description This lathe has been designed to give wood workers the option to customise the lathe to meet their requirements. Or to add to the lathe as there needs change. The lathe can be a centre lathe with bowl turning facility [up to 48” in diameter]. A copy lathe, spiral cutting lathe or all three depending on the option package that you select. If you require a longer distance between centres various optional bed extensions are available up to 100” [factory fitted option]. Identification. There is a plate at the back of the machine listing all the manufacturing data including the serial number, model, etc. General construction The lathe has been manufactured from cast iron and steel to give it a high mass that both helps to absorb any vibration that is generated during the turning process and insures that the machine is very stable. Each machine comes pre drilled for all the options so that you can add them later should your needs change. Headstock. The head stock houses the motor and main spindle. The spindle has 4 sealed for life bearings for maximum rigidity and taking the load exerted when turning up to 48” blanks. The spindle can be locked in up to 24 positions for fluting and indexing work. Tail stock. The tail stock is cast iron construction and accepts attachments with a number 3 morse taper mark 2 Bed of the lathe The bed is a square tubular construction with a short section that can be removed when turning bowls with a diameter of greater than 24” and less than 48”

Optional spiral gear holder

12

Tool rest Two tool rests are provided. A 10” tool rest that can move to most positions on the lathe bed is provided for normal spindle turning and a second tool rest is provided for large bowl turning. Electrical system The electrical control system is housed in a box that is on an extension cable. This allows the controls to be moved to a position to suit the job that you are doing. . The main on/off switch is located on the front of the headstock. A plug and socket are provided on the back of the machine to enable quick connection and disconnection of the electrical supply. No cable is supplied, as the length of the cable will be dependant on your installation. The lathe has a 3 HP Baldor 220-volt single or 3-phase Optional copy attachment. The copy attachment fits at the back of the lathe and will accept flat templates or round masters. Dust collection. The dust collection port is located at the back of the copy attachment. You will need a dust collection system with a minimum airflow of 65 feet / second and 1000 cubic feet per minute. Optional fluting or spiral fluting attachment. The flutes are produced by cutters that rotate in a router drill or similar tool [not provided] that is fitted to the copy carriage. The lathe spindle is detached from the motor and attached via a set of gears that rotate the spindle as the copy carriage is moved along the bed of the lathe. Optional bed extensions Bed extensions can be added to the end of the bed to give addition length if required. Where to locate your machine. Before you remove your machine from the pallet select the area where you will use your machine. There are no hard and fast rules for its location but below are a few guidelines. 2/ There should be sufficient area at the back of the machine to allow access for adjustments and maintenance to be conducted and if fitted you will need access to the copy attachment which is located at the back of the machine. 3/ Adequate lighting. The better the lighting the more accurate and safely you will be able to work 4/ Solid floor. You should select a solid flat floor, preferably concrete or something similar. 5/ Close to power source and dust collection. 6/ Allow an area for the storage of blanks and finished panels.

13

Lathe with the box removed

Unpacking your machine. To unpack your machine you will need tin snips, knife star screwdriver and a wrench. 1/ Using the tin snips cut the banding that is securing the packing box [If fitted]. WARNING: EXTREAM CAUSION MUST BE USED BECAUSE THE BANDING WILL SPRING AND COULD CAUSE INJURY. 2/ Dismantle the box 3/Using the knife cut the plastic wrap. The accessories that were ordered are in the box. 4/ Remove the base mounting bolts that secure the machine to the base of the box. 5/ To remove the lathe from the pallet, use a fork lift truck or a hoist with suitable slings with a lifting capability of 2000 Kg [4400lb]. Note The machine is heavy; ensure that you have sufficient people. Note: If you have any doubt about the described procedure, seek professional assistance. Do not attempt any procedure that you feel is unsafe or that you do not have the physical capability of achieving.

Pallet fixing bolts

14

If you need to move the lathe around with the top of the box removed you will need to use two pallet jacks as the base will bend if only one is used. It is therefor recommended that you move the lathe to the filal position before you remove the box top. Assembly and setup Adjusting the machine level The machine is provided with 4 bolts to adjust the lathe level. It is important that the lathe is level and does not rock. Fit the leveling bolts into the holes provided in the support leg and the head stock base leaving the lock nuts loose. Place a spirit level along the bed of the lathe and adjust the bolts until the machine is level. Place the spirit level at 90 degrees and adjust the bolts until the lathe is level in that direction. Re check and fine adjust if required then tighten the lock nuts. Note the machine must not rock on the bolts, as it will be unstable. Note the machine is provided with 2 holes in the head stock base and 2 in the support leg to allow you to bolt the lathe to the floor if you require [bolts not provided]. If you decide to bolt the lathe to the floor, do not over tighten the bolts as both parts of the machine are made of cast iron and if the lathe is not perfectly flat on the floor you could break the castings. Cleaning the machine. Remove the rust protection grease with WD 40 or similar solvent It is important that you remove all the grease and re lubricate with a Teflon bases lubricant. Teflon has fewer tendencies to attract sawdust and cause clogging. You should also wax the bed as this also protects the steel from rust.

Moving pallet with two pallet jacks

15

Connecting the electrical supply. The machine is supplied with a plug and socket for connection to the electrical supply. No cable is supplied, as this will depend on your installation. Ensure that your electrical supply matches that of your machine. Connect the ground wire [green or yellow green] as shown. Other wires can be connected in either socket. To remove the outer casing of the plug insert a flat screwdriver as indicated on the plug and twist. Note single-phase socket shown. Note. It is recommended that qualified personnel carry out the electrical installation. Ensure that the main supply corresponds with that of the machine. Use wiring suitable for the power and the length of cable that is needed for your installation. On the machine you will see a wire that is yellow and green, this is the ground wire, the other coloured wires are power phase it does not matter what colour combination you use, green/yellow is ground; all other wiring is power (there is no neutral). On single phase the wiring can be interchanged as you wish, it will not affect the rotation of the motor. The direction of rotation of machines with a single-phase supply is predetermined during production. It is recommended that you use a 30-amp mains breaker and number 12 cable for installation up to 15’. Installations 15’ to 30’ should use number 10-gauge cable. Fitting the face plate The face plate screws onto the thread of the headstock spindle. It is locked in position with an allen set screw which when tightened fits into a “v” groove to ensure that the face plate is securly held in place and will not come loose when the lathe is used in the reverse mode.

Electrical socket

Electrical plug

Earth /Ground wire

16

To fit the faceplate, lock the spindle by loosening the spindle locking knob and move towards the rear of the lathe. Rotate the spindle until the locking shaft locates in one of the indexing holes and tighten the knob. Screw the faceplate on to the spindle thread and tighten with the knock out rod as shown. Tighten the allen set screw. Disengage the spindle-locking shaft and tighten the knob to ensure that it will not accidentally engage. To remove the faceplate, reverse the procedure. Fitting the tool rest. Two tool rests are provided. One for center turning and the other for bowl turning. The saddles may come fitted to the bed of the machine, if they are not assembled, assemble as follows.

Spindle locking knob unlocked

Spindle locking knob locked

Fitting the face plate

Lock nut

“V” clamp

17

1/ Loosen the lock nut. 2/ Assemble the saddle onto the bed of the lathe. Ensure that the “V” clamp at the front is engaged with the lathe bed. 3/ Engage the “V” clamp at the rear of the lathe and tighten the lock nut. 4/ You will have to adjust the lock nut

so that the clamping handle at the front of the saddle is in a comfortable position when the saddle is locked. 5/ To disassemble reverse the procedure. Note the bowl turning saddle is the larger of the two. Fit the tool rest, adjust to the height that suits the job that you are doing and lock with the clamp handle.

Tool rest fitted to lathe

Under side of tool rest

Tool rest fitted

Bowl tool test

18

Fitting and removing the tailstock. To remove the tailstock, loosen the clamp handle and slide off the end of the bed. Note the tailstock is made from cast iron and is very heavy. Take care not to drop it or to damage the bed of the lathe when re fitting. Fitting and removing accessories into the tailstock. 1/ Rotate the handle so that the spindle moves forward.

2/ Clean the tapered part of the accessory and the tapered hole in the spindle. 3/ Firmly push the accessory into the spindle hole. 4/ Try to twist the accessory. It should be locked in position. To remove the accessory, rotate the spindle handle so that the spindle is moved into the tailstock. The accessory will be ejected from the spindle when the spindle is fully retracted. Note hold your hand under the accessory to ensure that the accessory does not fall onto the bed of the lathe when it is ejected. To clamp the tailstock spindle in position tighten the clamp screw on the backside of the tailstock.

Tailstock

Underside of tailstock

19

Fitting accessories into the head stock spindle. 1/ Clean the tapered part of the accessory and the tapered hole in the spindle. 3/ Firmly push the accessory into the spindle hole. 4/ Try to twist the accessory. It should be locked in position. To remove the accessory insert the knock out rod into the spindle hole from the end of the lathe and give the accessory a sharp knock. Note hold your hand under the accessory to ensure that the accessory does not fall onto the bed of the lathe when it is ejected.

Removing and fitting the bed bridge. The chain that the copy saddle uses for controlling the travel along the bed of the lathe will have to be removed. If left attached it will limit the diameter that can be turned. 1/ Move the copy saddle to the tail stock end of the lathe. It should not be in the way when you are turning. 2/ Loosen the panel clamping screws and remove the drive dog clamping nut. 3/ Remove the drive dog and the panel, which has keyhole slots for easy removal.

Knock out rod Drive centre

Bridge removed

Panel

Drive dog clamping nut Panel and drive dog removed

Keyhole slots

20

4/ Loosen the chain guard plate and remove. The plate has keyhole slots for easy removal.

5/ Loosen the chain by releasing the chain cam and slide the chain block off.

6/ Pull the chain through the headstock and remove it from the drive dog gear. It is not necessary to remove the chain from the copy saddle. 7/ Replace the panel and the drive dog to stop saw dust getting in to the enclosure.

8/ Leave the chain attached to the copy saddle and it is recommended that the chain is stored in a plastic bag attaches to the copy saddle. This should reduce the possibility of damage and help to keep the chain clean. 9/ To replace the chain reverse the procedure.

Chain guard plate loose

Chain guard plate removed

Chain cam

Chain removed from cam

Chain being removed

21

1/ Remove the screws that secure the bridge to the lathe bed and the support beside the headstock. Leaving the top screw on both sides of the bridge in place. 2/ Support the bridge and remove the last two screws. 3/ Gently slide the bridge out. 4/ Protect the bridge from any damage as any burrs or dents may mean that the bridge will not line up with the bed, tool saddles etc.

5/ To assemble the bridge reverse the procedure. 6/ The bridge is located on the bed of the lathe with dowel screws, which locate it ensuring that the “v” slides are aligned. Before finally tightening the screws check that both “V” slides are in line. Always tighten the screws to the bed of the lathe before tightening the screws by the headstock.

Bed extension. The bridge can be used as a short extension for the center lathe. Note. It will not extend the length of the copy attachment. To fit it to the end of the lathe 1/ Attach the bridge with the bolts but do not fully tighten. 2/ Move the tailstock so that it bridges both the lathe bed and the bridge. 3/ Tighten the tail stock clamp handle. This will line up both sets of “V’s” 4/ Tighten the clamp bolts. 5/ Un clamp the tailstock and move onto the bed of the lathe. 6/ Check that the “V’s“ are in line and that the tailstock moves over the transition smoothly. 7/ Readjust if required.

Removing screws

Bridge removed

Bridge fitted as an extension

22

Speed selection The lathe is provided with four pulley selections and variable speed. This allows you to select the correct speed for your job and also the correct torque. If you are turning a large bowl blank [48” in diameter] you will not only need to have a low speed but high torque as well. In this case the lowest set of pulleys will be required. The speed range is 0 to 3900 rpm / 0 to 2800 rpm / 0 to 1200 rpm / 0 to 450 rpm The variable speed control is located on the moveable control box. To change the pulley speed. 1/ Loosen the locking handle and lift the motor. 2/ Move the drive belt to the required set of pulleys. 3/ lower the motor and tighten the locking handle. Once the pulley speed has been selected you can adjust the speed by adjusting the speed control knob on the moveable control box to the required speed.

Pulley speed chart

Variable speed control knob

Drive belt loose Drive belt tight

Locking handle

23

Electrical controls. The main electrical controls are located on a movable box. Two locations are provided for the box, one on the headstock and the other on the tailstock. The main isolation switch is located on the headstock. 1/ Main isolation switch. This switch isolates the machine electrical system from the incoming electrical supply. The switch has the facility to be padlocked [padlock not provided] in the off position. If you are conducting maintenance work or require access to any of the electrical components of the machine you must isolate the machine from the electrical supply by removing the electrical connector from the machine as well as padlocking the main isolation switch in the off position. 2/ Start button. Pressing the green button starts the lathe motor. 3/ Stop button / emergency stop button. The red button covers both functions. Once pressed it must be pulled back out before the motor can be started. 4/Forward / reverse switch. The lathe motor can operate in both forward and reverse. Never operate the switch while the motor is moving as it could cause damage to the motor and exerts strain on the machine. If the locking screw has not been tightened in the faceplate or other accessories, it could become detached from the spindle and cause injury. 5/ Speed selection switch. Turning the speed selection switch increases or decreases the speed of the lathe spindle. 6/ Access door safety micro switch. When the door is opened a micro switch isolates the electrical system and stops the motor from operating. If your lathe will not start check that the door is fully closed and that the switch if functioning correctly.

Main isolation switch

Start button Stop button

Forward / Reverse button

Variable speed control knob

Tailstock mounted control box

Door safety switch

24

Machine test Now is the time to test the machine. 1/ Close the door. If you try to start the machine with the door open the machine will not start, as the safety switch is not made. 2. Check that there are no tools fitted, it is far safer to test the machine with out the tools fitted. 3/ Check that the red emergency /stop switch is in the fully out position. 4/ Check that the machine is clear of all tools and other loose objects. 5/ Check that all the adjusting and locking handles are tight. 6/ Start the lathe by pressing the green start knob. 7/ Now is the time to check that all the safety switches are functioning correctly before you fit any tools 8/ With the machine running, press the red emergency / stop switch. The motor should have the power removed and slow down 9/ With the machine running open the door very slowly until the door switch functions. The motor should have the power removed and slow down. Close the door and wait for the motor to completely stop before you fully open the doors. 10/. If any of the safety switches fail to operate correctly do not use the machine until the fault has been corrected. Indexing head The lathe is provided with an indexing head that can lock the spindle in up to 24 positions. To lock the spindle loosen the indexing pin clamping knob, move towards the indexing plate and rotate the spindle until the relevant hole lines up with the pin. Engage the pin and tighten the knob. The lathe is provided with a spindle clamping block that when activated will ensure that the spindle cannot move. This eliminates any backlash in the system. Various equal positions are achievable by using different combinations of holes as listed below. Divisions Pin numbers 2 = 12,24 3 = 8,16,24 4 = 6,12,18,24 6 = 4,8,12,16,20,24 8 = 3,6,9,12,15,18,21,24 12 = 2,4,6,8,10,12,14,16,18,20,22,24 24 = 1 to 24 It is recommended that the drive belt be removed when using the indexing.

Indexing pin loose

Indexing pin locked

25

Tool holder. The tool holder fits to the bed of the lathe as shown and can be positioned at any suitable position.

Spindle clamp block not engaged Spindle clamp block engaged

Tool holder

26

Optional copy attachment. Attach the left hand and right hand brackets as shown. Do not fully tighten the bolts. Attach the main bar as shown.

Measure from the bed to the top of the main bar at both ends and adjust the brackets untill the main bar is parallel. Once parallel tighten the bracket clamp bolts and re check that the main bar is parallel. Adjust if required.

Assemble the follower as shown.

Copy bracket

Copy bracket Main copy bar

Copy follower

27

Assemble the cutting tool as shown There are two methods of adjusting the main bar towards or away from the bed of the lathe. 1/ Rough adjustment is done by loosening the black plastic clamp handle and pushing the bar to the approximate position then. Once in position lock the black plastic handle. 2/ For fine adjustment. Loosen the round clamp knob on top of the main copy bar and adjust the position with the round knob at the end of the bracket. Once in position clamp the top clamp knob. The template holders can be adjusted to any position on the main copy bar by loosening the clamp bolt and sliding the holder to the required position and tightening the clamp bolt. The template holder will accept both templates and round masters. It is strongly recommended that all masters and templates are made from a hard marerial as soft material such as pine will become dammaged by the follower and give poor results.

Copy cutting tool

Clamp knob

Plastic clamp handle

Template / master holder clamp bolt

Fine adjusting knob

28

Fit the template as shown and tighten the clamp screws. Fit a master fit between centers and lock the screw with the lock ring. Once the master or template is in position adjust the lead in / lead out bracket so that the follower has a smooth transition at the ends of the master and the template. The main copy bar will have to be set parallel to the axes of the lathe [center line of the spindle]. The simplest way to achieve this is to place a round piece of wood between centers. Adjust the main copy bar so that the copy follower is running along it. Then cut the wood with the copy attachment. Once the wood has been turned, measure it at both ends and adjust the main bar until the wood being turned is the same dimension at both ends. Once the bar is parallel, scribe [scratch] a line and fill with a permanent marker on both support bracket both sides of the main copy bar support block. You can then use these marks a quick reference whenever you have to set up a new job.

The follower is controlled by a spring, which is located under the copy saddle at the back of the lathe. The spring pressure can be adjusted and comes factory set to suite most templates and masters. If you require to adjust the spring pressure, loosen both lock nuts, adjust the screw, and re tighten the lock nuts. Screwing the screw out will increase the follower pressure.

Lead in / lead out bracket

Template Master

Scribe line here

Copy saddle control spring

Lock nut

Clamp screws

29

To adjust the copy tool, fit the rotating center into the tailstock. Adjust the cutting tip of the tool so that it is level with the point of the rotating center. This will bring the cutting point of the tool onto the centerline of the spindle. The lathe tool holder can be adjusted to suite various diameters of job. Remove the holder fixing screws and reposition the holder to the required position and re clamp in position. Remember to re fit the plastic blanking screws into the holes as this will stop saw dust and dirt getting into the threads. There is a handy reference on the bed of the copy saddle that shows you the range of diameters that can be accommodated for the various positions. The knob at the front of the copy saddle controls adjustment of the cutting tool for different diameters. One complete rotation of the knob is 0.12”.

The handle on the copy saddle pulls the copy saddle forward and back against the spring and when completely released will allow the copy saddle to move to the position set by the control knob at the front of the copy saddle.

Copy follower

Plastic blanking screws

Copy tool adjusting knob

Copy tool control handle

30

The tool holder is provided with a dust port that you can attach your dust collector to. It is recommended that the minimum air flow of 1000 cubic feet per minute min and a velocity of 65 feet / min [The stronger the dust collector the better] is connected to the dust port.

Stops are provided to limit the travel of the copy saddle. They fit onto the bed of the lathe and clamp onto the “V’s”. Care should be taken when moving the saddle along the bed as you could move the stops if you use too much force on the horizontal movement handle.

To copy turn. There are several of ways to set up for copy turning and with experience, you will decide on the one that suits you. Below is one method that you can use and refine. 1/ Place the template in the “U” clamps provided, push the template so that the back of the template is flush with the main copy bar and clamp in position. If you are using a master, clamp between centres and lock in position. 2/ Adjust the saddle copy tool to the biggest radius of the job to be copied. You can do this by fitting a rotating centre into the tailstock and bringing the point of the centre in front of the saddle-cutting tool. Measure the distance between the centre point and the cutting point of the tool and adjust using the control knob. 3/ Move the saddle so that the copy follower is in front of the largest diameter of the job. Move to the back of the machine and loosen the two clamp screws on each side of the template holder bar. Slide the bar forward so that the template or master just touches the follower. Using the scribed lines on the bracket and a rule, adjust the main copy bar so that it is equal at both ends and the follower is just touching the largest diameter. 4/ Fit the blank into the lathe and turn, adjusting the control knob so that you cut progressively deeper cuts. Continue until the follower is contacting the template or master along the complete surface.

Dust extraction port

Copy saddle stop

Copy saddle stop

31

5/ Measure the job at both ends and check that it is correct. If you need to adjust the diameter, loosen the template holder bar clamps and adjust with the fine adjustment knobs. Note. When initially setting up, make the job over size as you can always adjust to make it smaller. Note. The copy attachment is controlled by a spring and you will find that it moves into radiuses easier than riding out of radiuses. This is especially true for small radiuses and steep angles. It is recommended that you control the follower with the saddle control handle so that the follower is allowed to move down the radius under the control of the spring and you move the follower out with the control handle. Continue this until you get to one end of the job. Then repeat the procedure from the other end of the job.

32

Optional flute cutting attachment. Cutting parallel flutes Remove the relevant set of blanking screws from the saddle and store in a safe place. When you remove the bracket, replace the blanking screws; they will keep the tapped holes clean. Attach the drill / router support bracket to the saddle. Several hole sets can be selected depending on the diameter of the job and the amount of extension that your drill or router has. Attach the drill or router [not provided] and set to the height required for your job. To set the cutter on the center height of the lathe, fit the rotating center into the tailstock and use the point as a reference. You can get different effects on the job by setting the cutter above or below the center height of the lathe. Note. Remove the drive belt from the motor while fluting. If you switch on the motor while the spindle is locked it will stall and it could cause damage. If you are using the spiral indexing system and the motor is switched on it could cause damage to your lathe. You can use the lathe indexing system described earlier in the manual or the spiral indexing system for indexing the spindle when parallel fluting but you can not use the lathe indexing system when spiral fluting.

Use the saddle depth control knob to adjust the depth of the cutter. Use the bed stops to control the length of the flute.

Drill fitted for flute cutting

Clamping screws

Drill collar clamping screw

Saddle depth control knob

33

When cutting spiral flutes you can only use the spiral indexing plate and never try to use the lathe indexing plate, as this will not allow the spindle to rotate. The spiral cutting indexing plate fits into the Morse taper of the headstock. Clean both the spindle hole and the taper shaft of the indexing plate and push into the head stock spindle hole. Test that the plate is fitted correctly and that the taper is holding by trying to twist it.

To rotate the indexing plate, remove the clamping screw, rotate the indexing plate to the required hole, and refit the screw.

Fit the gear arm as shown.

Swivel the gear arm down as shown.

Spiral indexing plate Rear of spiral indexing plate

Gear arm

Gear arm fitted

Clamping screw

34

Decide on the rotation that you require [Left hand or Right hand] and the pitch that you require. Select the gear set that is required for your job from the gear selection on the inside of the door. Note. There is an extra gear in the right hand spiral. This is used to reverse the rotation. Note. The center part of the gear diagram represents the gear arm. Note. Gears B and C fit onto the same shaft, which rotates both gears at the same time. All other gears fit onto a single shaft Note. The top gear numbered 96 [number of teeth] is the gear that is permanently fitted to the lathe spindle and the gear train engages with.

Spiral pitch gear chart

Fitting gear

Fitting gear

Fitting gear

Fitting gear

35

Note. When assembling the gears they must mesh snugly. If they are too loose there will be play in the system, which could cause chatter and a bad surface finish. If they are too tight the system will be difficult to operate. Rotate the gear arm so that it meshes with the spindle gear and lock in position by tightening the allen screw as shown.

Note. Remove the drive belt from the motor when using the spiral cutting attachment. To engage the copy saddle with the gears, loosen the clamp screw, rotate the dog so

that the drive lines up, and push forward. Lock the clamp nut. When you have finished spiral cutting and have disassembled the gears

remember to disengage the drive dog and clamp in the disengaged position with the clamp nut.

Gears engaged with spindle gear

Clamp gear arm Drive dog not engaged

Drive dog engaged

Clamp nut

36

Applying the spindle break block will help remove any backlash in the system and improve the finish of the cut. Do not over tighten as the block is meant to exert light pressure. If you over tighten the block you will not be able to move the saddle along the bed and will be putting extra strain on the system.

Note. Never place your fingers between the gears as they could crush your finger.

Note. It is recommended that you use a router for cutting flutes, as drills are not designed to take side ways pressure and the bearings could ware out with prolonged use. Note. You can use the copy function while cutting flutes both spiral and straight. There are certain limitations when cutting radiuses which will depend on the design of the job. Note. Use the bed stops to control the length of the flute.

Spindle break

Un safe

37

Optional rotating steady

38

The rotating steady moves with the copy saddle and supports the job close to the copy cutter. The steady has a cutter that will turn the blank prior to the job moving into the steady. This is a useful function as it allows you to turn none round stock. Assembling the optional rotating steady onto the copy saddle Two additional centres are provided. Both have are extended so that they pass through the rotating rings. Note that one is the drive centre and fits into the headstock spindle and the other rotates and fits into the tailstock. To assemble the rotating steady to the copy saddle The rotating steady must be positioned accurately on the centre line of the lathe spindle both vertically and horizontally. 1/ Fit the base to the copy saddle with the screws provided. Do not fully tighten them until the adjustments are complete

39

Turning parallel using the copy saddle. The copy saddle can turn parallel jobs by simply using the slide travel limiter that is a black knob mounted on the front of the saddle. To turn repetitive parallel jobs simply adjust the knob till the sectioned being turned is at the correct diameter. The lathe is now set and will turn jobs to the same diameter repetitively. This is a handy function when turning dowels. Note. Constantly check the finished product for size as the setting could change and you could produce rejects. If you are turning short large diameter jobs you will probably not need to use the rotating steady but if the job is long and thin it will be an advantage. The most useful feature of the rotating steady is its ability to turn square stock round in a single pass. Assembling the pre cutter. A second cutting tool is fitted onto the rotating steady that is used as a pre-cutter. This tool turns the rough stock to a diameter that will fit the bushing that has been selected. It has two bolts/nuts that clamp the housing in position and an adjusting knob. The tool is clamped in position by two Allen screws. Selecting a support bushing in the rotating steady. The rotating steady has a number of bushings that support jobs of various sizes. Select a ring that is the next size up from the biggest diameter of the job. Remove the row of screws and clamp plates that hold the ring in place and then remove the rings. Replace the screws and the clamp plates in the removed ring, you do not want to loose them. Using the pre cutter, turn the stock to a snug fit in the selected bushings. This will support the job and provide a stable work piece for the copy cutter. Assembly and adjusting the pre cutter. 1/ Fit the tool into the holder and clamp in position with the 2 Allen screws. The cutter should protrude 28mm to 30mm [1 1/8”] 2/ Loosen the pivot bolt, clamp bolt / nut. 3/ Move the tool with the adjusting knob to the approximate position to cut the diameter that you have selected. Ensure that the tool is on the centreline of the job, tighten the clamp bolt and pivot bolt. 4/ Complete a trial cut and measure the diameter. 5/ Adjust the tool to compensate for the error by loosening the clamp bolt and turning the adjusting knob. The top nut will act as a pivot. Once you have completed the adjustment tighten the lower clamp bolt and complete a second trial cut. 6/ Refine the tool position if required.

40

Maintenance General. Keep your machine clean. At the end of each day clean the machine. Wood contains moisture and if sawdust or wood chips are not removed they will cause rust. In general we recommend that you only use a Teflon based lubricant on the lathe. Regular oil attracts dust and dirt and the Teflon tends to dry and has fewer tendencies to accumulate dirt and saw dust. The exception is the copy saddle, which is provided with two grease nipples. Any good quality grease can be used and the saddle should be greased every 12 hours of use. After greasing, wipe off any excess grease that is visible. Periodically check that all nuts and bolts are tight. Drive belt The drive belt should last for many years [depending on the usage] but need to be inspected regularly for cracks, cuts and general wear. If damage is found replace the belt. Bearings. All bearings are sealed for life and do not require any maintenance. If a bearing becomes faulty replace it. Rust The lathe is made from steel and cast iron. All none painted surfaces will rust if not protected. It is recommended that applying wax protects them or a Teflon based lubricant Copy saddle chain adjustment. The chain that controls the lateral movement of the saddle comes factory set and should not need adjustment. The chain is provided with an adjustment screw and nut [nut located inside the copy saddle]. If you need to adjust the chain, hold the chain attachment screw steady [it has two flats] so that the chain is not twisted and retention.

Grease nipples

Chain tensioning screw

41

Copy saddle “V” guide adjustment. Blocks that are on eccentric cams control the clearance between the bed and the copy saddle. By loosening the shaft clamping screw and rotating the eccentric the clearance is adjusted. It is not recommended that the adjustment be changed unless excessive ware has taken place. If adjustment is required loosen the clamp screw and rotate the shaft with an allen key until there is a snug fit between the bed and the copy saddle. The copy saddle should move smoothly with out excessive side ways movement. Copy saddle bed wipers. The copy saddle is provided with nylon wipers that assist in removing any dirt that is on the bed of the lathe when the copy saddle moves along the bed. The pads will need to be removed, cleaned and readjusted periodically. When refitting the wipers ensure a snug fit between the wiper and the bed. They should not be too tight on the bed, as this will cause excessive ware to the wipers.

Tailstock “V” guide adjustment. “V” blocks that are on screw threads can be adjusted to change the position that the clamping handle rests in when in the clamped

position. To adjust the tailstock to bed loosen the locknut, rotate the screw and re clamp the locknut. Note It is important that both screws are rotated the same amount. If the screws are moved different amounts the adjustable “V” blocks will not function correctly.

Saddle “V”guide block

Shaft clamping screw

Copy saddle bed wipers

Underside of tailstock

Tailstock adjusting screw and lock nut

42

Troubleshooting. Lathe will not start. 1/ Check that the start switch is being pressed full in. 2/ Check that the red emergency / stop switch is fully out. 3/ Check that the electrical power cord is plugged into the power outlet. 4/ Check that the electrical supply is on [reset the breaker]. 5/ Check that door is closed. 6/ With the power disconnected from the machine, check the wiring to the plug is correct. Check that the rubber insulation is stripped enough and is not causing a bad connection. Check that all the screws are tight. 7/ Test the safety circuit. The machine will not stop. This is a very rare occurrence as the machine is designed to fail-safe. If it should occur and you cannot fix the fault, seek professional assistance. The machine must be disconnected from the power and never run until the fault has been rectified. 1/ Stop switch faulty. Replace the stop switch. 2/ Internal breaker faulty. Replace the breaker. Motor tries to start but will not turn. 1/ With the power disconnected from the machine. Try to turn the spindle by hand. If the spindle will not turn, check the reason for the jamming. 2/ Spindle clamp block left engaged. 3/ Capacitor faulty. Replace the capacitor. 4/ Motor faulty. Replace the motor. 5/ Spindle lock or spiral gears engaged. Disengage. Motor overheats. The motor is designed to run hot, but should it overheat it has an internal thermal overload protector that will shut it down until the motor has cooled and then it will reset automatically. If the motor overheats wait until it has cooled and restart. If the motor shuts down consistently check for the reason. Typical reasons are dull cutting tools, motor cooling fan clogged or faulty, motor-cooling fins clogged, over feeding the job and excessive ambient temperature. Squeaking noise. 1/ Check that the motor cooling fan is not contacting the fan cover. 2/ Check the bearings. 3/ Check the drive belt. Spindle slows down during a cut. 1/ Loose drive belt. Re-tension the belt. 2/ Dull cutting tools. Replace the tool or have it re-sharpened. 3/ Feeding the wood too fast. Slow down the feed rate. 4/ Oil or dirt on the drive belt. Clean or replace the drive belt. Machine vibrates. 1/ Machine not level on the floor. Re-level the machine ensuring that it has no movement.

43

2/ Damaged drive belt. Replace the belt. 3/ Job is not balanced. Change to slower speed and or balance the job 4/ Damaged pulley. Replace the pulley.

44

45

46

LTL.00.00.00.00 WOOD TURNING LATHE

1 LTL.00.00.00.11 LEVELING BOLT 4 2 BDS 744-83 NUT М16 4 3 LTL.00.00.00.12 TAIL LEG 1 4 BDS 833-82 SPRING WASHER 2-12Н 12 5 BDS 2171-83 SCREW М12Х45 12 6 LTL.03.00.00.00 BODY 1 7 DIN 1481 SPRING PIN ø8Х45 4 8 TL-4-547 STOPPER ø55 7 9 LTL.01.04.00.01 COVER 1

10 ISO 7380 SCREW М 6Х10 8 11 LTL.01.00.00.08 BRACKET 1 12 BDS 2171-83 SCREW М 6Х12 15 13 LTL.01.00.00.01 HEADSTOCK COLUMN 1 14 LTL.01.00.00.07 FRONT COVER 1 15 LOCKING HANDLE LAGUNA 1 16 BDS 2171-83 SCREW М 6Х25 2 17 BDS 206-78 WASHER АМ 6 1 18 DIN 985 NUT М 6 1 19 LTL.01.02.00.00 DOOR 1 20 LTL.01.00.00.09 LOCKING PIN 1 21 LTL.01.00.00.10 KNURLED HANDLE 1 22 LTL.01.00.00.03 UPPER COVER 1

47

LTL.02.00.00.00 MAIN DRIVING

1 DIN 7991 SCREW М 6Х16 6 2 LTL.02.02.00.02 CLAMPING RING 1 3 LTL.02.02.00.05 SPINDLE BUSHING 1 4 LTL 02.02.00.01 SPINDLE 1 5 LTL.02.02.00.06 BIG BUSH 1 6 RADIAL BEARING WITH BALLS 6210-ZZ 2 7 LTL.02.02.00.08 MIDDLE BUSH 1 8 LTL.02.02.00.09 NUT М50x1.5 1 9 BDS 3389-62 KEY 10Х8Х56 1 10 BDS 2171-83 SCREW М 6Х25 1

48

11 BDS 833-82 SPRING WASHER 2-6Н 1 12 LTL.02.02.00.04 SMALL BUSH 1 13 RADIAL BEARING WITH BALLS 6008-ZZ 2 14 DIN 7991 SCREW М 6Х10 1 15 LTL.02.00.00.06 NUT M30x1.5 1 16 LTL.02.00.00.04 PULLEY 1 17 LTL.02.00.00.08 INDEXING GEAR WHEEL Z=96; m=1.5 1 18 VEE BELT XPZ L=1287 1 19 BDS 1230-85 BOLT М10Х30 4 20 LTL.02.01.02.01 MOTOR PULLEY 1 21 BDS 2171-83 SCREW М 8Х30 1 22 BDS 833-82 SPRING WASHER 2-8Н 1 23 LTL.02.01.02.02 WASHER 36х8.5х4 1 24 GN603-78-М10-DGN HANDLE М10 1 25 LTL.02.01.00.04 BUSH 1 26 DIN 933 BOLT М10Х55 2 27 BDS 206-78 WASHER АМ10 9 28 LTL.02.01.00.03 MOTOR ADJUSTING PLATE 1 29 BDS 2171-83 SCREW М10Х45 1 30 BDS 744-83 NUT М10 8 31 BDS 833-82 SPRING WASHER 2-10Н 4 32 AR90L- B3 MOTOR 1 33 LTL.02.01.01.00 MOTOR SUPPORT PLATE 1

49

LTL.04.01.00.00 TEMPLATE SUPPORT

[Optional]

1 CL.00.03.00.28 COTTER 2 2 LTL.04.01.05.00 FRONT BRACKET 1 3 BDS 206-78 WASHER AM 8 4 4 LTL.04.01.00.29 AXIS 2 5 DIN 985 NUT M 10 2 6 BDS206-78 WASHER AM 8 7 LTL.04.01.00.09 HANDLE 6 8 CL.00.03.00.11 SCREW 2 9 LTL.04.01.01.00 REAR BRACKET 1 10 BDS 1230-85 BOLT М10Х25 4 11 BDS 2171-83 SCREW M 6x20 4 12 BDS 833-82 SPRING WASHER

2-6Н 16

13 LTL.04.01.00.32 REMOTE STRIP II 1

50

14 LTL.04.01.00.04 BEAM 1 15 LTL.04.01.00.26 STUD 2 16 LTL.04.01.00.13 STRIP 2 17 LTL.04.01.00.14 BOTTOM STRIP 4 18 BDS 2171-83 SCREW M 6x30 8 19 CL.00.03.00.22 BOTTOM STRIP 2 20 LTL.04.01.00.16 BASIC STRIP 2 21 LTL.04.01.00.24 SAFETY STRIP 2 22 CL.00.03.00.09 CENTRE 2 23 DIN 134 WASHER M 8 2 24 BDS 2171-83 SCREW M 8x25 6 25 BDS 2171-83 SCREW M 6x25 4 26 LTL.04.01.00.21 STRIP 2 27 LTL.04.01.00.12 UPPER STRIP 2 28 BDS 1230-85 BOLT М12x20 2 29 CL.00.03.00.21 UPPER STRIP 2 30 GN603-63-М8-

25-DGN HANDLE M8x25 2

31 LTL.04.01.00.23 HANDLE 2 32 LTL.04.01.00.06 REMOTE STRIP I 1

51

LTL.04.03.00.00 SUPPORT [Optional]

1 LTL.04.03.00.02 AXIS 2 2 BDS 2171-83 SCREW М 8x60 4 3 BLOCK 4 4 DIN 471 RING FOR SHAFT ø12 4 5 LTL.04.03.00.05 ECCENTRIC AXIS 2 6 BDS 833-82 SPRING WASHER 2-8Н 4 7 DIN 913 STOP SCREW М 8x 8 4 8 LTL.04.03.01.00 SUPPORT PLATE WITH PADS 1 9 LTL.04.03.00.17 SUPPORT BUSHING 1 10 DIN 134 WASHER M 6 1 11 BDS 2171-83 SCREW М 6x40 1 12 BDS 206-78 WASHER AM 8 2 13 DIN 985 NUT М 8 5 14 DIN 913 STOP SCREW М 6Х 8 8 15 LTL.04.03.00.08 ACROSS SUPPORT 1 16 LTL.04.03.00.07 GUIDING AXIS 4 17 LTL.04.03.00.10 GUIDE 2 18 BDS 744-83 NUT М8 2 19 LTL.04.03.00.22 SPRING TIE- BAR 1 20 LTL.04.03.00.18 SPRING 1 21 DIN 551 STOP SCREW М8Х10 16 22 LTL.04.03.00.09 STOP 1 23 LTL.04.03.00.14 SCREW 1 24 GN736.1-52-Z10-A-S HANDLE 1 25 BDS 1640-81 OIL CUP 3.1 2

52

LTL.04.04.00.00 SUPPORT MECHANISM [Optional]

1 BDS 2171-83 SCREW М10Х90 1 2 LTL.04.04.00.21 HANDLE-80-10.5 1 3 ISO 7380 SCREW М 6Х20 1 4 UN 732 WASHER ø7x ø35x2.5 1 5 DIN 439 LOW NUT М 10 1 6 CL.01.00.00.22 HANDWHEEL ø200 1 7 DIN 1481 SPRING PIN ø5Х30 1 8 DIN 471 RING 15 4 9 RADIAL BEARING WITH BALLS 6202-2Z 6 10 LTL.04.04.00.16 REMOTE BUCHING 1 11 LTL.04.04.00.01 SUPPORT BOX 1 12 DIN 914 STOP SCREW М 8x10 1 13 DIN 914 STOP SCREW М 5x5 3 14 LTL.04.04.00.02 LONG AXIS 1 15 LTL.04.04.00.03 GEAR- WHEEK- SHAFT Z=16 1 16 CL.01.00.00.25 GEAR- WHEEL Z=70 1 17 CL.01.00.00.12 CHAIN- WHEEL Z=17 2 18 DIN 472 RING 35 1 19 ДМ5-321.20.00.97 CHAIN- WHEEL 1 20 CL.01.00.00.28 SHORT AXIS 1 21 DIN 913 STOP SCREW М 8x10 2

53

LTL.05.00.00.00 TAIL STOCK

1 LTL.05.00.00.26 HANDLE-60-M12 1 2 LTL.05.00.00.25 TIGHTENING LEVER 1 3 LTL.05.00.00.24 SPECIAL NUT 1 4 LTL.05.00.00.23 SUPPORT BUSH 1 5 LTL.05.00.00.28 TIGHTENING STUD 1 6 LTL.05.00.00.27 CLAMPING ARM 1 7 DIN 1481 SPRING PIN ø 8Х50 1 8 DIN 439 THIN NUT М12 2 9 LTL.05.00.00.01 TAIL STOCK 1 10 T419 RULER - 0 - 140 mm FOR CL1200 1 11 LTL.05.00.00.03 TAIL STOCK BARREL 1 12 LTL.05.00.00.17 HANDLE- KNURLED 1 13 DIN 7991 SCREW М 5 8 14 DIN 1481 SPRING PIN ø 5Х10 2 15 LTL.05.00.00.04 NUT Tr 24x3 LH 1 16 LTL.05.00.00.20 STRIP 4 17 LTL.05.00.00.06 SCREW Tr 24x3 LH 1 18 BDS 3389-62 KEY 1 19 LTL.05.00.00.22 CLAMP BLOCK 2 20 DIN 933 BOLT М12Х120 2 21 RADIAL BEARING WITH BALLS 6304-ZZ 1 22 LTL.05.00.00.08 BEARING CAP 1 23 BDS 833-82 SPRING WASHER 2-8Н 4 24 BDS 2171-83 SCREW М 8Х25 4 25 LTL.05.00.00.09 SPACER BUSH 1 26 LTL.05.00.00.11 HANDWHEEL- ø127 1 27 DIN 134 WASHER M16 1 28 DIN 439 THIN NUT М16 1 29 DIN 439 THIN NUT М 8 1 30 LTL.05.00.00.15 HANDLE-60-8.5 1 31 BDS 2171-83 SCREW М 8Х70 1

54

LTL.07.03.00.00 TOOL REST- MANUAL

1 LTL.07.03.00.01 TOOL REST 1 2 LTL.07.03.00.02 BASE 1 3 LTL.07.03.00.03 GUIDE 1 4 LTL.07.03.00.11 CLAMPING BLOCK 1 5 LTL.07.03.00.09 FLANGE 1 6 BDS 2171-84 SCREW М 4Х16 4 7 LTL.07.03.00.10 SPECIAL SCREW 1 8 LTL.05.00.00.25 TIGHTENING LEVER 2 9 LTL.05.00.00.26 HANDLE-60-M12 2 10 LTL.07.03.07.01 BUSH 2 11 LTL.07.03.00.08 CAP 1 12 DIN 1481 SPRING PIN 1 13 LTL.07.03.07.02 WEDGE BLOCK 2 14 DIN 471 CIR CLIP ø20 2 15 LTL.07.03.00.05 ECCENTRIC AXIS 1 16 LTL.07.03.00.04 SPECIAL BOLT 1 17 BDS 206-78 WASHER АМ16 2 18 DIN 985 NUT М16 2 19 LTL.07.03.00.06 BODY 1

55

LTL.07.10.00.00 TRAVELING REST [Optional]

LTL.07.10.00.00 TRAVELING REST

1 LTL.07.10.00.05 STEADY REST 1 2 ISO 7380 SCREW М 10x35 2 3 DIN 7349 WASHER М10 5 4 LTL.07.10.00.06 STRIP 1 5 DIN 913 STOP SCREW М 6x 6 1 6 LTL.07.10.00.07 STRIP FOR ADJUSTMENT 1

56

7 ISO 7380 SCREW М6x30 2 8 LTL.07.10.00.09 TIGHTENING STUD 1 9 LTL.07.10.00.08 TIGHTENING STRIP 1 10 DIN 985 NUT М 10 1 11 DIN 1481 SPRING PIN ø 6x30 2 12 DIN 125A WASHER M6 2 13 ISO 7380 SCREW М8x16 3 14 ISO 7380 SCREW М6x20 2 15 DIN 1481 SPRING PIN ø 6x16 4 16 ISO 7380 SCREW М6x25 2 17 LTL.07.10.01.05 BLOCK 1 18 BDS 206-78 WASHER AM 6 2 19 LTL.07.10.01.07 RING 1 20 LTL.07.10.01.06 SCREW 1 21 LTL.07.10.01.04 SUPPORT COTTER 1 22 BDS 744-83 NUT М6 2 23 LTL.07.10.01.02 SLIDE- BLOCK 1 24 DIN 913 STOP SCREW М10x20 2 25 LTL.07.10.01.03 TIGHTENING COTTER 1 26 LTL.07.10.01.01 BASE 1 27 BDS 206-78 WASHER AM 8 1 28 RADIAL BEARING WITH BALLS

6024-ZZ 1

29 ISO 7380 SCREW М 8x20 1 30 BDS 1230-85 BOLT М10x35 2 31 DIN 1481 SPRING PIN 1 32 СL.07.01.00.20 STRIP 18 33 ISO 7380 SCREW М 5x 8 18 34 СL.07.01.18.01 RING ø100 1 35 СL.07.01.18.02 RING ø80 1 36 СL.07.01.18.03 RING ø60 1 37 СL.07.01.18.04 RING ø40 1 38 СL.07.01.18.05 RING ø20 1 39 LTL.07.10.00.00 CHIP- CATCHER FOR STEADY

REST 1

57

LTL.04.00.00.00 COPYING DEVICE [Optional]

1 LTL.04.04.00.00 SUPPORT MECHANISM 1 2 LTL.04.05.00.02 ECCENTRIC 1 3 DIN 471 RING 15 7 4 LTL.04.05.00.03 STRETCHING BLOCK 1 5 BDS 833-82 SPRING WASHER 2-8Н 15 6 BDS 2171-83 SCREW М 8Х55 8 7 CL.01.00.00.34 BRUSH 4 8 LTL.04.00.00.41 TWIN SUPPORT 1 9 LTL.04.06.00.00 CONTROL LEVER 1

10 LTL.04.00.00.19 HANDLE-90-M12 1 11 BDS 206-78 WASHER АМ 8 10

39

58

12 BDS 2171-83 SCREW М 8Х30 1

13 LTL.04.01.00.00 SUPPORT FOR TEMPLATE 1

14 BDS 744-83 NUT М8 3

15 LTL.04.00.00.12 STUD 1

16 DIN 7991 SCREW М 8Х20 1 17 LTL.04.00.00.13 STRIP 6Х20Х135 1

18 DIN 985 NUT М 8 6

19 DIN 7971C SCREW FOR WOOD 2.9Х13 4

20 BDS 2171-83 SCREW М 6Х16 1

21 LTL.04.05.00.01 BUSHING 1

22 LTL.04.00.00.20 TENSION STRIP 1

23 DIN 1481 SPRING PIN ø 5Х12 1

24 LTL.04.00.00.22 FRONT- LEFT SUPPORT 1 25 ISO 7380 SCREW М 6Х10 8

26 ISO 7380 SCREW М 6Х20 9

27 LTL.04.00.00.27 CLEANER L=50 4

28 LTL.04.00.00.26 CLEANER L=24 4

29 LTL.04.00.00.25 REAR SUPPORT 2

30 LTL.04.02.00.02 SENSOR 1

31 ISO 7380 SCREW М 8Х25 6

32 LTL.04.02.01.00 SENSOR SUPPORT 1 33 BDS 206-78 WASHER АМ12 1

34 BDS 744-83 NUT М12 1

35 LTL.04.03.00.00 SUPPORT 1

36 LTL.04.00.00.32 SHAVING COLLECTOR 1

37 LTL.04.00.00.21 FRONT- RIGHT SUPPORT 1

38 DIN 7982 C SCREW FOR WOOD 2.9Х13 4

39 LTL.04.00.00.31 KNIFE HOLDER 1

40 DIN 913 STOP SCREW М 8Х10 3

41 LTL.04.00.00.45 TENSION AXIS 1 42 CL.01.00.00.12 CHAIN- WHEEL Z=17 1

43 RADIAL BEARING WITH BALLS 6202-2Z

1

44 06B-1 CHAIN t=9.525 1

45 CL.01.00.00.33 LONG TIE- BAR 1

46 BDS 744-83 NUT М10 2

59

LTL.04.08.00.00 STOP FOR LONGITUDINAL MOVEMENT [Optional]

1 DIN 603 SCREW М6X45 2 2 LTL.04.08.01.02 WEDGE 4 3 LTL04.08.01.03 STRIP 2 4 LTL.04.08.01.01 STRIP 2 5 DIN 985 NUT М 6 2 6 DIN 315 WING NUT M6 2 7 DIN 134 WASHER M 6 2 8 LTL.04.08.01.04 STRIP WITH LEFT CHANNEL 1 9 LTL.04.08.02.04 STRIP WITH RIGHT CHANNEL 1 10 DIN 7991 SCREW М 6Х12 6 11 DIN 603 SCREW М6X50 2

60

LTL.07.02.00.00 RUNNING CENTRE МК3-Ø50

1 LTL.07.02.00.03 BODY 1 2 DIN 471 RING FOR SHAFT Ø17 1 3 RADIAL BEARING WITH BALLS 6203-ZZ 2 4 LTL.07.02.00.02 BUSHING 1 5 DIN 472 RING FOR OPENING Ø40 1 6 LTL.07.02.00.01 CENTRE 1

61

LTL.07.10.03.00 RUNNING CENTRE МК3-Ø20 [Optional]

1 LTL.07.02.00.03 BODY 1 2 DIN 471 RING FOR SHAFT Ø17 1 3 RADIAL BEARING WITH BALLS 6203-ZZ 2 4 LTL.07.02.00.02 BUSHING 1 5 DIN 472 RING FOR OPENING Ø40 1 6 LTL.07.10.03.01 CENTRE 1

62

LTL.07.05.00.00 STAND FOR CHISELS

1 LTL.07.05.00.01 BASE 1 2 LTL.07.05.00.02 WEDGE 2 3 UN 732 WASHER ø7ХФ35Х2.5 2 4 DIN 315 WING NUT M6 2 5 DIN 603 SCREW М6X35 2

63

OTHER ACCESSORIES

1 LTL. 07.00.00.02 LEVER FOR KNOCK- OUT 1 2 CL.07.00.00.18 KNIFE FOR EXTERNAL TURNING 16х16

[Optional] 1

3 CL.07.00.00.12 V- KNIFE 1 4 LTL.07.00.00.01 LEADING COGWHEEL CENTRE ø40 1 5 LTL.07.10.00.10 LEADING COGWHEEL CENTRE ø20

[Optional] 1

6 LTL.07.01.00.00 FACE PLATE 10'' 1

64

LTL.07.04.00.00 PIPE TOOL REST

1 LTL.07.03.00.06 BODY 1 2 LTL.07.03.07.00 BRACKET 2 3 LTL.07.03.00.08 COVER 1 4 LTL.05.00.00.26 HANDLE-60-M12 2 5 LTL.05.00.00.25 TIGHTENING LEVER 2 6 DIN 1481 SPRING PIN ø8Х30 1 7 LTL.07.04.00.04 SPECIAL BOLT 1 8 LTL.07.03.00.05 ECCENTRIC AXIS 1 9 DIN 471 RING FOR SHAFT ø20 2 10 DIN 985 NUT М16 2 11 BDS 206-78 WASHER АМ16 2 12 LTL.07.03.00.10 SPECIAL SCREW 1 13 BDS 2171-84 SCREW М 4Х16 4 14 BDS 833-82 SPRING WASHER 2-4Н 4 15 LTL.07.03.00.09 FLANGE 1 16 LTL.07.04.00.02 BASE 1 17 LTL.07.03.00.11 CLAMPING BLOCK 1 18 LTL.07.04.00.03 COTTER 1 19 LTL.07.04.01.00 SUPPORT 1

65

LTL.06.02.00.00 STAND FOR MILLING MACHINE [Optional]

1 LTL.06.02.01.00 STAND 1 2 ISO 7380 SCREW М 8Х25 3 3 BDS 206-78 WASHER АМ 8 4 4 LTL.06.02.04.01 CLAMP 1 5 BDS 2171-83 SCREW М 8Х45 1

66

LTL.06.01.00.00 SPIRAL MECHANISM [Optional]

1 LTL.06.01.04.04 BUSHING 1 2 LTL.06.01.04.08 HANDLE 1 3 LTL.06.01.04.05 INDEXING DISC 1 4 DIN 471 RING FOR SHAFT ø17 1 5 DIN 7991 SCREW М 6Х16 24 6 RADIAL BEARING WITH BALLS 6003-ZZ 1 7 LTL.06.01.04.07 STRIP FOR DEVISION 1 8 LTL.06.01.04.01 TAPER AXIS 1 9 LTL.06.01.05.01 BLOCK TO THE BRAKE 1 10 BDS 833-82 SPRING WASHER 2-8Н 4 11 BDS 2171-83 SCREW М 8Х45 2 12 LTL.06.01.05.02 STOP STRIP 1

67

13 LTL.06.01.05.03 STRIP 1 14 BDS 206-78 WASHER АМ10 1 15 BDS 1230-85 BOLT М10Х35 1 16 DIN 1481 SPRING PIN ø 5Х10 1 17 LTL.06.01.03.07 GEAR WHEEL Z= 108; m=1.5 1 18 DIN 471 RING 15 5 19 LTL.06.01.03.01 GEAR WHEEL Z= 34; m=1.5 1 20 LTL.06.01.01.05 STRIP 5 21 ISO 7380 SCREW М6Х30 5 22 LTL.06.01.03.04 GEAR WHEEL Z= 51; m=1.5 1 23 DIN 7991 SCREW М 8Х20 2 24 BDS 206-78 WASHER АМ12 2 25 LTL.06.01.01.02 TIGHTENING WASHER 2 26 LTL.06.01.01.08 RIGHT FLANGE 1 27 BDS 2171-83 SCREW М 6Х16 2 28 LTL.06.01.01.07 BUSHING 2 29 LTL.06.01.01.10 COTTER 36Х6Х8 7 30 LTL.06.01.01.04 BUSHING 2 31 LTL.06.01.01.03 AXIS 2 32 LTL.06.01.01.09 LEFT FLANGE 1 33 LTL.06.01.03.02 GEAR WHEEL Z= 36; m=1.5 1 34 LTL.06.01.03.03 GEAR WHEEL Z= 48; m=1.5 1 35 LTL.06.01.01.06 SHAFT 1 36 LTL.06.01.03.05 GEAR WHEEL Z= 68; m=1.5 1 37 LTL.06.01.03.06 GEAR WHEEL Z= 72; m=1.5 1 38 LTL.06.01.02.02 OUTGOING SHAFT 1 39 LTL.06.01.01.01 APRON 1 40 BDS 2171-83 SCREW М 8Х30 1 41 BDS 3389-62 COTTER 6Х6Х20 2 42 LTL.06.01.02.05 COVER 1 43 RADIAL BEARING WITH BALLS 6004-ZZ 4 44 LTL.06.01.02.03 LONG REMOTE BUSHING 1 45 LTL.06.01.02.04 SHORT REMOTE BUSHING 1 46 BDS 2171-83 SCREW М 8Х20 2 47 LTL.06.01.02.08 SHAFT 1 48 RADIAL BEARING WITH BALLS 6202-2Z 1 49 LTL.06.01.02.06 COVER 3 50 LTL.06.01.02.09 CHAIN WHEEL Z=17 1 51 LTL.06.01.02.10 BUSHING 1 52 LTL.06.01.02.11 TIGHTENING HANDLE 1 53 LTL.06.01.02.01 BODY FOR THE SCREW GEAR 1 54 LTL.06.01.02.07 GEAR WHEEL z= 19; m=2 2

LIMITED WARRANTY New woodworking machines sold by Laguna Tools carry a one-year warranty effective from the date of shipping. Laguna Tools guarantees all new machine sold to be free of manufacturers’ defective workmanship, parts and materials. We will repair or replace, without charge, any parts determined by Laguna Tools, Inc. to be a manufacturer’s defect. We require that the defective item/part be returned to Laguna Tools with the complaint. In the event the item/part is determined to be damaged due to lack of maintenance, cleaning or misuse/abuse, the customer will be responsible for the cost to replace the item/part, plus all related shipping charges. This limited warranty does not apply to natural disasters, acts of terrorism, normal wear and tear, product failure due to lack of maintenance or cleaning, damage caused by accident, neglect, lack of or inadequate dust collection, misuse/abuse or damage caused where repair or alterations have been made or attempted by others. Laguna Tools, Inc. is not responsible for additional tools or modifications sold or performed (other than from/by Laguna Tools, Inc.) on any Laguna Tools, Inc. woodworking machine. Warranty maybe voided upon the addition of such described tools and/or modifications, determined on a case-by-case basis. Normal user alignment, adjustment, tuning and machine settings are not covered by this warranty. It is the responsibility of the user to understand basic woodworking machinery settings and procedures and to properly maintain the equipment in accordance with the standards provided by the manufacturer. Parts, under warranty, are shipped at Laguna Tools, Inc.’s cost either by common carrier, FEDEX ground service or a similar method. Technical support to install replacement parts is primarily provided by phone, fax, e-mail or Laguna Tools Customer Support Website. The labor required to install replacement parts is the responsibility of the user. Laguna Tools is not responsible for damage or loss caused by a freight company or other circumstances not in our control. All claims for loss or damaged goods must be notified to Laguna Tools within twenty-four hours of delivery. Please contact our Customer Service Department for more information. Only new machines sold to the original owner are covered by this warranty. For warranty repair information, call 1-800-332-4094. Copyright 2010 Laguna Tools, Inc. **Warning - no portion of these materials may be reproduced without written approval from Laguna Tools, Inc.

Laguna Tools is not responsible for errors or omissions. Specifications subject to change. Machines may be shown with optional accessories.

© 2018, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved.

2072 Alton Parkway. Irvine, CA 92606Ph: 800.234.1976 | www.lagunatools.com