PSS GSS Artica Profile GE Side-BY-Side Refrigerator Service Manual
PFSS6NKW GE Refrigerator Service Manual
-
Upload
911servicetech -
Category
Documents
-
view
241 -
download
0
Transcript of PFSS6NKW GE Refrigerator Service Manual
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
1/89
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
2/89– 2 –
IMPORTANT SAFETY NOTICE
The information in this service guide is intended for use byindividuals possessing adequate backgrounds of electrical,electronic, and mechanical experience. Any attempt to repair amajor appliance may result in personal injury and propertydamage. The manufacturer or seller cannot be responsible for theinterpretation of this information, nor can it assume any liability inconnection with its use.
WARNING
To avoid personal injury, disconnect power before servicingthis product. If electrical power is required for diagnosis or testpurposes, disconnect the power immediately after performing thenecessary checks.
RECONNECT ALL GROUNDING DEVICES
If grounding wires, screws, straps, clips, nuts, or washers used tocomplete a path to ground are removed for service, they must bereturned to their original position and properly fastened.
GE Consumer & Indust rial
Technical Service Guide
Copyr ight © 2008
All rights reserved. This service guide may not be reproduced in whole or in partin any form without written permission from the General Electric Company.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
3/89– 3 –
Table of Contents
Articulating Door Mullion ...........................................................................................................................................62
Auger Motor Assembly ................................................................................................................................................61
Circuit Boards ..................................................................................................................................................................65
Components .....................................................................................................................................................................29
Components Locator Views ......................................................................................................................................25
Compressor ......................................................................................................................................................................52
Condenser Fan ................................................................................................................................................................43
Control Board Connector Locator ..........................................................................................................................27
Control Features .............................................................................................................................................................19
Control Panel Operation .............................................................................................................................................67
Damper Assembly .................................................................................... ................................................................... 56
Defrost Cycle ....................................................................................................................................................................24
Defrost Heaters ........................................................................................................... ............................................... 49
Dispenser Assembly ....................................................................................................................................................54
Dispenser Display Assembly ....................................................................................................................................53
Dispenser Heater ..........................................................................................................................................................55
Dispenser Lock ................................................................................................................................................................24
Door Gaskets .................................................................................................................. .................................................. 34
Duct Heater ..................................................................................................... .............................................................. 50
EMI Filter and Power Cord ..................................................................................................... ..................................... 51
Evacuation and Charging Procedure ............................................................................................. ...................... 9
Freezer Basket and Drawer ..................................................................................................... .................................. 32
Freezer Door Handle ...................................................................................................................................................13
Freezer Evaporator . ......................................................................................................... ........................................... 39
Freezer Evaporator Cover .................................................................................................... .................................... 37
Freezer Fan .................................... ..................................................................................... ............................................ 40
Fresh Food Crispers and Pans .................................................................................................................................31
Fresh Food Door Handle ............................................................................................................................................12
Fresh Food Evaporator ....................................................................................................... ...................................... 37
Fresh Food Evaporator Cover ................................................................................................. ...............................35
Fresh Food Fan ....................................................................................................... .................................................... 42
Fresh Food Shelves and Bins ....................................................................................................................................29
(Continued next page)
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
4/89– 4 –
Ice Bucket and Icemaker ...........................................................................................................................................59
Ice Room Blower ......................................................................................................... ................................................ 41
Installation .......................................................................................................................................................................11
Interior Airflow .................................................................................................................................................................10
Interior Lights ...................................................................................................................................................................34
Introduction ................................................................................................................ ...................................................... 5
Light Time-Out Function .............................................................................................................................................24
Machine Compartment Cover ................................................................................................... ............................43
Nomenclature ......................................................................................................... ......................................................... 6
Over Temperature Thermostats .............................................................................................. ...........................48
Pantry Drawer Assembly ..........................................................................................................................................55
Pantry Drawer Control ...............................................................................................................................................56
PTCR Relay, Run Capacitor, and Overload Assembly .................................................................................... 52
Refrigeration Components .................................................................................................... .................................... 8
Refrigeration System .......................................................................................................... ......................................... 8
Removing the Freezer Door .....................................................................................................................................15
Removing the Refrigerator Door ............................................................................................... ............................13
Replacing Evaporators Using the LOKRING Method .....................................................................................40
Schematic ..........................................................................................................................................................................87
Technical Data ........................................................................................................ ......................................................... 7
Test Mode Operation ....................................................................................................................................................71
Thermistors .......................................................................................................................................................................45
Top Table ............................................................................................................................................................................33
Troubleshooting ..............................................................................................................................................................71
Vegetable and Fruit Drawers Shelf .......................................................................................................................55
Warranty ...........................................................................................................................................................................88
Water Tank .................................................................................................................. ................................................... 57
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
5/89– 5 –
The new Profile Bottom Mount Refrigerators have the following features:
Available in 26-cubic foot capacity with fresh food french door configuration.•
ENERGY STAR• ® qualified.
Integrated Dispenser with Crushed•Ice, Water, and Actual TemperatureDisplay― Features easy-to-reach,easy-to-read temperature controlsand a setting to quickly restore propertemperature after frequent dooropenings.
• An articulating door mullion attachedto the left-side door providesa movable center mullion thatmaximizes access to the fresh foodcompartment.
Secure-Close Door Systems ― •Securely pulls the doors and drawersshut, even after you release thehandles.
• ClimateKeeper™ with DualEvaporators― Uses two evaporatorsto maintain higher humidity for freshfoods.
Freshness Center™― Offers•maximum convenience by utilizingtwo humidity-controlled drawers and1 full-length adjustable temperature deli drawer.
An external "air" thermistor changes the control setting based on ambient condition to keep the fresh•food and freezer at the correct temperature.
TurboCool• TM ― Rapidly cools the refrigerator compartment in order to more quickly cool foods.
TurboFreeze― Rapidly cools the freezer compartment in order to more quickly freeze foods.•
LED Lighting― Casts a clean, beautiful light throughout the fresh food area of the refrigerator. (GE•Reveal™ Lighting in freezer.)
Available in white or black finish or stainless wrap.•
Introduction
Note:Features may vary by model.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
6/89– 6 –
Nomenclature
The nomenclature tag is located on the left wallof the fresh food compartment. It contains thefollowing information:
Exterior ColorWW - White on WhiteBB - Black on BlackSS - Stainless Steel
Model YearW - 2007
Brand/Product
P - Profile
Capacity6 - 26 Cubic Foot
Mini-Manual Location
• Model and SerialNumber
• Minimum InstallationClearances
• Electrical Voltage,Frequency
• Maximum AmperageRating
• Refrigerant Chargeand Type
Nomenclature
P F S S 6 N K W S S
ExteriorF - High GlossS - Stainless
Ice/Water
K - External Cubed & Crushed Ice &Water, 1Year Filter/Icemaker
Style
S - Standard Depth
ConfigurationF - French Door w/FZ Drawer
Feature Pack
N - Full Width Meat Pan
The letter designatingthe year repeats every12 years.
Example:
T - 1974
T - 1986
T - 1998
Serial NumberThe first two numbers of the serial numberidentify the month and year of manufacture.
Example: AR 123456S = January , 2008
A - JAN 2008 - RD - FEB 2007 - MF - MAR 2006 - LG - APR 2005 - HH - MAY 2004 - GL - JUN 2003 - FM - JUL 2002 - DR - AUG 2001 - AS - SEP 2000 - ZT - OCT 1999 - VV - NOV 1998 - T
Z - DEC 1997 - S
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
7/89– 7 –
Technical Data
DISCONNECT POWER CORD BEFORE SERVICING
IMPORTANT - RECONNECT ALL GROUNDING DEVICES
All parts of this appliance capable of conducting electrical current aregrounded. If grounding wires, screws, straps, clips, nuts or washers used
to complete a path to ground are removed for service, they must be
returned to their original position and properly fastened.
ELECTRICAL SPECIFICATIONSTemperature Control (Position 5) ...........................................................16-(-11)°FDefrost Control (w/no door openings) ...........................................................16hrs
Thermistor kilo-ohm resistance .....................................................-2°F.......30.6
.........................................................................................................38°F.......11.6
.......................................................................................................77°F.........5.0k Overtemperature Thermostat ................................................................140-104°FDefrost Thermistor ............................................................................................50°FElectrical Rating: 115V AC 60 Hz ..................................................................5.2 AMaximum Current Leakage .......................................................................0.75 mA
Maximum Ground Path Resistance .............................................................0.14
NO LOAD PERFORMANCEControl Position 5/5 and Ambient of 70°F to 90°FFresh Food, °F ........................................................................................33 to 42°F
Frozen Food, °F .........................................................................................-7 to 3°FRun Time, % @ 70°F .................................................................................25 to 45Run Time, % @ 90°F .................................................................................45 to 75
REFRIGERATION SYSTEMCompressor 26 Model ...........................................................................897BTU/hrMinimum Equalized Pressure@ 90°F...............................................................................................60 to 65 PSIG@ 110°F.............................................................................................75 to 82 PSIG
REFRIGERANT CHARGE (R134a)26 Model ............................................................................................5.643 ounces
IMPORTANT SAFETY NOTICE
This information is intended for use by individuals possessing adequate
backgrounds of electrical, electronic and mechanical experience. Anyattempt to repair a major appliance may result in personal injury and
property damage. The manufacturer or seller cannot be responsible for
the interpretation of this information, nor can it assume any liability inconnection with its use.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
8/89– 8 –
Refrigeration System
Refrigeration Components
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
9/89– 9 –
Evacuation and Charging Procedure
WARNING:
• Before cutting or using a torch onrefrigerant tubes, recover the refrigerantfrom the system using approved recoveryequipment.
• Never charge new refrigerant through thepurge valve. This valve is always located onthe high pressure side of the system.
• Never apply heat from any source to acontainer of refrigerant. Such action willcause excessive pressure in the container.
• Always wear goggles when working withrefrigerants and nitrogen holding charge insome replacement parts. Contact with thesegases may cause injury.
1. Attach the hose from the R-134a chargingcylinder to the process tube port on thecompressor.
2. Evacuate the system to a minimum 20-in.vacuum using the refrigerator compressor andrecovery pump, which is attached to the newdrier assembly.
3. Turn off the recovery pump. Close the ball valveon the hose connected to the high-side portconnection. Add 3 ounces of R-134a refrigerant
to the system. Let the refrigerator operate andcirculate the refrigerant for 5 minutes.
4. Open the ball valve. Recover the purge/sweepcharge using the recovery pump and therefrigerator compressor until a 20-in. vacuumis attained. Close the ball valve and remove therecovery hose.
5. Charge the system with the exact amount ofR-134a refrigerant specified.
6. Disconnect the power cord to the refrigerator.This allows the pressure to equalize. After 3 to5 minutes, the low side pressure will be positiveand then the hose-to-charging port can bedisconnected.
7. Using an electronic leak detector, check allbrazed joints and both schrader ports. Reinstallcaps to schrader.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
10/89– 10 –
Interior Airflow
FanFan
FanFan
Air inlet)(Air inlet)Air inlet)(Air inlet)
Heat exchangerHeat exchanger
FanFan
(Air inlet)(Air inlet)
Heat exchanger
Air Flow (side view) Air Flow (front view)
The fresh food evaporator fan forces air through the evaporator into the fresh food compartment. Air fromthe evaporator can also pass through the pantry room damper/heater assembly to the deli drawer, throughthe fresh food compartment, and return to the evaporator. The damper/heater assembly is controlled by themain control board. When open, the damper allows the chilled air from the fresh food evaporator to moveinto the deli drawer. Air returns from the fresh food compartment to the fresh food evaporator via two returnvents located on the top left and right sides of the evaporator cover.
The freezer evaporator fan forces air through the evaporator into the freezer compartment. An additional iceroom fan circulates air into and returns air from the ice room via plastic conduits embedded in the cabinetfoam insulation. Air returns from the freezer compartment to the freezer evaporator via two return ventslocated on the bottom of the evaporator cover.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
11/89– 11 –
Installation
POWER CORD
The power cord of this appliance is equipped witha 3-prong (grounding) plug, which mates with astandard 3-prong (grounding) wall outlet to minimizethe possibility of electric shock hazard from thisappliance.
Have the wall outlet and circuit checked by aqualified electrician to make sure the outlet isproperly grounded.
If the outlet is a standard 2-prong outlet, it is yourpersonal responsibility and obligation to have itreplaced with a properly grounded 3-prong walloutlet.
WARNING:Do not, under any circumstances, cutor remove the third (ground) prong from the powercord. For personal safety, this appliance must beproperly grounded.
The refrigerator should always be plugged into itsown individual electrical outlet, which has a voltagerating that matches the rating plate.
USE OF EXTENSION CORDS
Because of potential safety hazards under certainconditions, we strongly recommend against the useof an extension cord.
However, if you must use an extension cord, itis absolutely necessary that it be a UL-listed (inthe United States) or a CSA-listed (in Canada),3-wire grounding type appliance extension cordhaving a grounding type plug and outlet, and thatthe electrical rating of the cord be 15 amperes(minimum) and 120 volts.
REFRIGERATOR LOCATION
• Do not install the refrigerator where thetemperature will go below 60°F (16°C) because it
will not run often enough to maintain propertemperatures.
• Do not install the refrigerator where thetemperature will go above 100°F (37°C) because itwill not perform properly.
• Install it on a floor strong enough to support it fullyloaded.
CLEARANCES
Allow the following clearances for ease of installation,proper air circulation and plumbing and electricalconnections.
Sides 1/8″ (3 mm)Top 1″ (25 mm)Back 1″ (25 mm)
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
12/89– 12 –
Fresh Food Door Handle
REMOVE THE FRESH FOODDOOR HANDLEStainless steel:
REMOVINGTHE DOORHANDLE: Loosenthe set screwswith the 3/32″ Allen wrenchand removethe handle.
Plastic handle:REMOVINGTHE DOOR
HANDLE: Slidethe handle upand off of themountingfasteners.
NOTE: If the handle mounting fasteners need tobe tightened or removed, use a Phillips-headscrewdriver.
A
A
4
MountingFasteners
MountingFasteners
Badge
Badge
A
A
ATTA CH THE FRESH FOOD
DOOR HANDLE
Stainless steel handle:
Attachthehandletothehandle
mountingfastenersandtightenthesetscrewswitha3/32“ Allenwrench.
Plastic handle:
Attachthehandleto thehandlemounting
fastenersbyaligningtheslotswiththehandlemounting fasteners.
Slideit downuntilit isfirmlylockedintoposition.
A
A
6
A
MountingFasteners
Mountingfasteners
Slotsonback
ofhandle
A
A
ATTACH THE FRESH FOODATTACH THE FRESH FOODDOOR HANDLEDOOR HANDLEStainless steel handleStainless steel handle:
Plastic handlePlastic handle:
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
13/89– 13 –
Freezer Door Handle Removing the Refrigerator Door
REMOVE THE REFRIGERATOR DOORSOpen the refrigerator doors.
Remove the two caps with a flat-headscrewdriver.
Remove the three screws on top with a Phillips-
head screwdriver.
Disengage the two electrical connectors.
To disconnect the water coupling, push in on thegray color of the coupling and pull out the tubing.
Remove the two grounding cables with a Phillips-head screwdriver.
Remove three 10 mm hex-head bolts (rightand left).
CAUTION: When the bolts areremoved, the door may fall and cause personalinjury and/or damage to the door itself.
E
F
G
A
B
C
D
(Continued next page)
REMOVE THE FREEZER DOORHANDLEStainless steel and plastic handles:
Loosen the set screws located on the undersideof the handle with the 1/8″ Allen wrench and
remove the handle.NOTE: If the handle mounting fasteners need tobe tightened or removed, use a Phillips-headscrewdriver.
A
5
A
ATTACH THE FREEZER DOORHANDLEStainless steel and plastic handles:
Attach the handle firmly to the mountingfasteners and tighten the set screws on thebottom of the handle with a 1/8″ Allen wrench.
A
7
A
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
14/89– 14 –
REPLACING THE REFRIGERATOR DOORSInstall the center hinge on each side.
Lower the refrigerator door onto the center hingepin. Ensure that the plastic hinge pin thimble ison the center hinge pin or inside door hinge pinhole located in the bottom of the door.
Securely tape the door shut with masking tapeor have a second person support the door.
A
B
C
REMOVE THE REFRIGERATORDOORS (cont.)
Lift the door straight up to remove.
Remove the two hex-head bolts and two Phillips-head screws from the center hinge. Set the hinge,bolts and screw aside.
I
H
REPLACING THE REFRIGERATORDOORS (cont.)
Insert the top hinge pin into the hinge hole ontop of the refrigerator door. Make sure the dooris aligned with the cabinet and opposite door.Attach the hinge to the top of the cabinet. Donot tighten bolts completely.
On left-hand doors, pass the wires and water linethrough the top hinge pin. Then connect thewater line and two connectors.
Attach the ground wire with a Phillips-head
screwdriver at the right and left hinge.Make sure the gasket on the door is flush againstthe cabinet and is not folded. Make sure the dooris straight and the gap between the doors is evenacross the front. While holding the aligned doorin place, tighten the top hinge bolts.
Reconnect the two connectors at each side of thetop cap and reattach the three Phillips-headscrews on top.
E
F
G
D
H
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
15/89– 15 –
Removing the Freezer Door
(Continued next page)
REMOVE THE FREEZER DOOR (cont.)Use the tip of a screwdriver to separate the railfrom the rail cover. Tilt the front end up and liftthe entire door.
Set the door front on a nonscratching surface.
Push the rail assemblies back into the cabinet.
CAUTION: Push both sides of the railassemblies back at the same time.
E
F
G
REPLACING THE FREEZER DOORTwo people may be required to completethis procedure.
ATTACH AND SECURE THE DRAWERFRONT TO THE SLIDESPull out the rail assemblies to the full length oneach side of the cabinet.
CAUTION: Make sure to pull out theside rails evenly.
A
1
REMOVE THE FREEZER DOORPull the freezer door open to full extension.
Remove the freezer bin by pulling both bracketsupward at the same time. (See page 8.)
Take out the lower basket by lifting the basket upfrom the rail system. (See page 10.)
Remove the two 10 mm hex-head bolts from theright and left side.
A
B
C
D
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
16/89– 16 –
REPLACING THE FREEZER DOOR (cont.)Hang the freezer door front onto open slotson the sides.
Tighten screws completely. (There are four10 mm hex-head bolts.)
REPLACE THE FREEZER BASKET
Replace the freezer basket by lowering it intothe frame.
B
C
2
Slot
REPLACING THE FREEZER DOOR (cont.)
REPLACE THE FREEZER BIN
Hook the ends of the freezer bin into bothbrackets, and push down until they lockinto place. (See page 8.)
3
LEVEL THE REFRIGERATORThe leveling legs have 2 purposes:
1) Leveling legs adjust so the refrigeratoris firmly positioned on the floor anddoes not wobble.
2) Leveling legs serve as a stabilizingbrake to hold the refrigerator securelyin position during operation andcleaning. The leveling legs also preventthe refrigerator from tipping.
Turn the leveling legs clockwise to raise therefrigerator, counterclockwise to lower it.
CAUTION: To avoid possiblepersonal injury or property damage, theleveling legs must be firmly touchingthe floor.
8
A
Flat-Head Screwdriver
(Continued next page)
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
17/89– 17 –
LEVEL THE REFRIGERATOR DOORSRemember a level refrigerator is necessaryfor getting the doors perfectly even. If youneed help, review the previous section onleveling the refrigerator.
If you open the freezer door, you can seethe center hinge.
Insert the supplied 4 mm Allen wrench
into the shaft of the center hinge.
9
A
B
Whenthe leftdoor islowerthan therightdoor.
Whenthe leftdoor ishigherthan therightdoor.
Adjustmentpoint
Adjustmentpoint
LEVEL THE REFRIGERATORDOORS (cont.)Adjust the height by turning clockwiseor counterclockwise. When you turncounterclockwise, the door will move up.
After adjusting the doors, please insert thesupplied fastener ring using a pair of pliersin the gap between the hinge grommet andthe center hinge. The number of fastenerrings you will need to insert depends onthe gap.
NOTE: Four fastener rings are enclosedwith the refrigerator. Thickness of eachfastener ring is 0.04″ .
9
D
C
LEVEL THE FREEZER DOOR
Locate the height adjuster in the freezerdoor. Slightly loosen the four Phillips-head screws from the door on each side(right and left).
Loosen the controller screw with aPhillips-head screwdriver to adjust thelevel.
10
A
B
(Continued next page)
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
18/89– 18 –
LEVEL THE FREEZER DOOR (cont.)Find the best position to align the doorslope.
After adjustment, tighten all the screws.
10
C
D
Example: The slope is about2 mm as shown below.
Rotate the height adjuster to +2.0to reduce the door slope.
ReferencePlane
Slope
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
19/89– 19 –
Control Features
About the controls with temperature settings.
The temperature controls are preset in the factory at 38°F for the refrigerator compartment and -2°F for the freezer compartment. Allow 24 hours for the temperature to stabilize to the preset recommended settings.
The temperature controls can display both the SET temperature as well as the actual temperature in the refrigerator and freezer. The actual temperature may vary slightly from the SET temperature based on usage and operating environment.
To change the temperature, press and release theADJUST FREEZER or ADJUST REFRIGERATOR pad.The display will show the actual temperature. Tochange the temperature, tap either the ADJUST FREEZER or ADJUST REFRIGERATOR pad until thedesired temperature is displayed.
Once the desired temperature has been set,the temperature display will return to the actualrefrigerator and freezer temperatures after 10seconds. Several adjustments may be required.
Each time you adjust controls, allow 24 hours for therefrigerator to reach the temperature you have set.
Changing the Temperature
NOTE: The refrigerator is shipped with protective film covering the temperature controls.If this film was not removed during installation, remove it now.
(Hold 3 secto Lock Control)
ICE OFF/LOCK
(Hold 3 secfor Turbo Cool)
ADJUSTREFRIGERATOR
Light ON/OFF(Hold 3 seconds)
ALARM/LIGHT
(Hold 3 secto Reset Filter)
ICE & WATER
(Hold 3 secfor Turbo Freeze)
ADJUSTFREEZER
ENERGYSAVER TURBO FREEZE TURBO COOL
RESET FILTER CUBED CRUSHED WATER
ICEOFF
˚ F 38˚ F Recommended
˚ F -2˚ F Recommended
CLIMATE KEEPER
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
20/89– 20 –
About Energy Saver
This product is equipped with an Energy Saver feature. The refrigerator is shipped
with the Energy Saver feature off.
Over time, moisture can form on the front surface of the refrigerator cabinet and
cause rust. If moisture does appear on thefront surface of the refrigerator cabinet,turn off the Energy Saver feature by pressing and releasing the ENERGY SAVER pad on the control panel.
5
About TurboCool ™ and TurboFreeze.™ ge.com
How it Works
TurboCool rapidly cools the refrigeratorcompartment in order to more quicklycool foods. Use TurboCool when adding alarge amount of food to the refrigeratorcompartment, putting away foods after they
have been sitting out at room temperatureor when putting away warm leftovers. It canalso be used if the refrigerator has been
without power for an extended period.
The compressor and fresh food fan willrun immediately until the fresh foodtemperature cools to approximately 25°F(–4°C), maximum run time two-and-a-half hours. After reaching 25°F (–4°C), freshfood compartment will run at cold settingfor one hour and return to the originalsetting value.
How to Use
Press and hold the ADJUST REFRIGERATOR pad for 3 seconds until you hear the soundand the displays.
After TurboCool is complete, the refrigeratorcompartment will return to the originalsetting.
NOTES: The refrigerator temperaturecannot be changed duringTurboCool .
The freezer temperature is not affected during TurboCool .
(Hold 3 secfor Turbo Cool)
ADJUSTREFRIGERATOR
About Door Alarm
The door alarm will sound if any dooris open for more than 3 minutes. Thebeeping stops when you close the door.
ENERGYSAVER
About Dispenser Light
Press and hold the ALARM/LIGHT pad for
3 seconds to turn on the dispenser light.To turn off , press and hold the pad againfor 3 seconds.
Light ON/OFF(Hold 3 seconds)
ALARM/LIGHT
How it Works
TurboFreeze rapidly cools the freezercompartment in order to more quicklycool foods. Use TurboFreeze when addinga large amount of food to the freezercompartment, putting away foods after they have been sitting out at room temperatureor when putting away warm leftovers. It canalso be used if the refrigerator has been
without power for an extended period.
The compressor and fresh food fan willrun immediately and keep running fortwo-and-a-half hours.
How to Use
Press and hold the ADJUST FREEZER padfor 3 seconds until you hear the soundand the displays.
After TurboFreeze is complete, the freezercompartment will return to the originalsetting.
NOTES: The freezer temperature cannotbe changed during TurboFreeze .
The refrigerator temperature isnot affected during TurboFreeze .
When opening the freezer doorduring TurboFreeze, the fans willcontinue to run if they havecycled on.
(Hold 3 secfor Turbo Freeze)
ADJUSTFREEZER
This product is equipped with an Energy Saver feature. The refrigerator is shipped with the Energy Saver feature on. Over time, moisture can form on the front surfaceof the door mullion and dispenser recess and can cause rust. If moisture does appearon the front surface of the door mullion and dispenser recess, turn off the Energy
Saver feature by pressing and releasing the ENERGY S VERENERGY SAVER pad on the control panel.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
21/89– 21 –
Water Filter Cartridge
The water filter cartridge is located in theback upper right corner of the refrigeratorcompartment.
When to Replace the Filter
There is a replacement indicatorlight for the water filter cartridge on thetemperature display. This light will turnorange to tell you that you need to replacethe filter soon. The filter cartridge shouldbe replaced when the replacement indicator light turns red or if the flowof water to the dispenser or icemakerdecreases.
Installing the Filter Cartridge
If you are replacing the cartridge,first remove the old one by slowly turning it counterclockwise. A small
amount of water may drip down.
CAUTION: If air has been trapped in the system, the filter cartridge may be ejected as it is removed. Use caution when removing.
Remove the protective foil from theend of the cartridge.
Lining up the arrow on the cartridgeand the cartridge holder, place thetop of the new cartridge up insidethe holder. Do not push it up intothe holder. Slowly rotate the cartridgeclockwise until it stops. As you turnthe cartridge, it will automaticallyraise itself into position. Cartridge
will rotate about 1/4 turn. Do not overtighten .
Run water from the dispenser for3 minutes (about 11 ⁄ 2 gallons) to clearthe system and prevent sputtering.See To Use the Dispenser section.
Press and hold the ICE & WATER padfor 3 seconds.
NOTE: A newly installed water filtercartridge may cause water to spurt fromthe dispenser.
Filter Bypass Plug
You must use the filter bypass plug when areplacement filter cartridge is not available.The icemaker will not operate without thefilter or filter bypass plug.
Replacement Filters:
To order additional filter cartridgesin the United States, visit our Website,ge.com, or call GE Parts and Accessories,800.626.2002.
Filter Model MWF
Customers in Canada should consultthe yellow pages for the nearest MabeService Center.
About the water filter.
(Hold 3 secto Reset Filter)
ICE & WATER
CartridgeHolder
Filter
BypassPlug
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
22/89– 22 –
Refrigerator Lights
An authorized technician will need toreplace the LED light.
Replacing the light bulbs.
Freezer Light
CAUTION: Light bulbs may be hot.Unplug the power cord from the outlet.
Pull drawer out to the stop position.
Rotate the shield down while pushingit backwards to remove it.
Turn the bulb counterclockwise.
Replace with an appliance bulb of thesame or lower wattage.
Replace the shield.
Plug the refrigerator back in.
NOTE: Appliance bulbs may be ordered from GE Parts and Accessories, 800.626.2002.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
23/89– 23 –
About the automatic icemaker. ge.com
Automatic Icemaker The icemaker will produce seven cubesper cycle—approximately 100–130 cubesin a 24-hour period, depending on freezer
compartment temperature, roomtemperature, number of door openingsand other use conditions.
If the refrigerator is operated before the water connection is made to the icemaker,turn on the ICE OFF feature by pressing andreleasing the ICE OFF/LOCK pad on thecontrol panel and the displays.
When the refrigerator has been connectedto the water supply, turn off the ICE OFF feature by pressing and releasing the ICE OFF/LOCK pad on the control panel.
The icemaker will fill with water when it cools to 15°F (–10°C). A newly installedrefrigerator may take 12 to 24 hours to
begin making ice cubes.
You will hear a buzzing sound each timethe icemaker fills with water.
Throw away the first few batches of ice to
allow the water line to clear.Be sure nothing interferes with the sweepof the feeler arm.
When the bin fills to the level of the feelerarm, the icemaker will stop producingice. It is normal for several cubes to be
joined together.
If ice is not used frequently, old ice cubes will become cloudy, taste stale and shrink.
NOTE: In homes with lower-than-average water pressure, you may hear the icemaker cycle multiple times when making one batch of ice.
NOTE: Turn on the ICE OFF feature if the water supply is shut off.
ICEOFF
A newly installed refrigerator may take 12 to 24 hours to begin making ice.
To Use the Dispenser
Select CUBED , CRUSHED or WATER by pressing the ICE & WATER pad.
Press the glass gently against the top of thedispenser cradle.
The spill shelf is not self-draining. Toreduce water spotting, the shelf shouldbe cleaned regularly.
If no water is dispensed when the refrigerator is first installed, there may be air in the water line system.Press the dispenser arm for at least two minutes to remove trapped air from the water line and to fill the water system. To flush out impurities in the water line, throw away the first six full glasses of water.
CAUTION: Never put fingersor any other objects into the ice crusher discharge opening.
To Lock and Unlock the Dispenser
To lock, press and hold the ICE OFF/LOCK pad for 3 seconds. Repeat this step tounlock the dispenser.(Hold 3 secto Lock Control)
ICE OFF/LOCK
Dispenser Light
Press and hold the ALARM/LIGHT pad for3 seconds to turn the dispenser light on
and off.
The light also comes on when the dispensercradle is pressed.
Light ON/OFF(Hold 3 seconds)
ALARM/LIGHT
Important Facts About Your Dispenser ■■Do not add ice from trays or bags to the storage drawer.
It may not crush or dispense well.
■■ Avoid overfilling glass with ice and use of narrow glasses.Backed-up ice can jam the chute or cause the door in thechute to freeze shut. If ice is blocking the chute, poke it through with a wodden spoon.
■■Beverages and foods should not be quick-chilled in theice storage drawer. Cans, bottles or food packages in thestorage drawer may cause the icemaker or auger to jam.
■■To keep dispensed ice from missing the glass, put theglass close to, but not touching, the dispenser opening.
■■Some crushed ice may be dispensed even though youselected CUBED ICE . This happens occasionally when a few cubes accidentally get directed to the crusher.
■■ After crushed ice is dispensed, some water may drip fromthe chute.
■■Sometimes a small mound of snow will form on the door inthe ice chute. This condition is normal and usually occurs when you have dispensed crushed ice repeatedly.The snow will eventually evaporate.
(Hold3sectoLockControl)
ICEOFF/LOCK
(Hold3secforTurboCool)
ADJUSTREFRIGERATOR
LightON/OFF(Hold3seconds)
ALARM/LIGHT
(Hold3sectoResetFilter)
ICE & WATER
(Hold3secforTurboFreeze)
ADJUSTFREEZER
ENERGYSAVER TURBO FREEZE TURBO COOL
RESET FILTER CUBED CRUSHED WATER
ICEOFF
˚ F 38˚ F Recommended
˚ F -2˚ F Recommended
CLIMATEKEEPER
Spill Shelf
11
ICE & WATER
(Hold 3 secto Lock Control)
ICE OFF/LOCK
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
24/89– 24 –
Defrost Cycle
Fresh Food Defrost Cycle
The refrigerator evaporator utilizes an adaptivedefrost cycle that operates a metal sheath heater toremove frost from the evaporator.
If the main board senses any door opening, the
defrost cycle is every 12 hours. Otherwise, thedefrost cycle is 16 hours.
The control board determines the length of timethe heater is energized. It does this by monitoringthe fresh food evaporator thermistor. Once thetemperature of the thermistor reaches 54°F(12°C), the control cycles the defrost heater off.A bimetal safety thermostat provides a backupin the event the evaporator thermistor fails. Thesafety thermostat prevents the temperature fromexceeding 140°F (60°C).
Freezer Defrost Cycle
The freezer evaporator utilizes an adaptive defrostcycle that operates a metal sheath heater toremove frost from the evaporator.
If the main board senses any door opening, thedefrost cycle is every 12 hours. Otherwise, thedefrost cycle is 16 hours.
The control board determines the length of time theheater is energized. It does this by monitoring the
freezer evaporator thermistor. Once the temperatureof the thermistor reaches 50°F (10°C), the controlcycles the defrost heater off. A bimetal safetythermostat provides a backup in the event theevaporator thermistor fails. The safety thermostatprevents the temperature from exceeding 140°F(60°C).
Dispenser Lock
When the dispenser system is locked, actual andset temperatures can be viewed but no dispensercommand will be accepted. This includes thedispenser cradle and will prevent accidentaldispensing that may be caused by children or pets.If a pad or the cradle is depressed with the system
locked, it will not be acknowledged.
Light Time-Out Function
The refrigerator incorporates a light time-outfunction for the fresh food and freezer sections. Ifeither of the fresh food doors or the freezer draweris left open for 10 minutes, the main control boardwill turn off the lights in that section. If the opendoor or drawer is closed, and then reopened, thetimer in the main control board will reset for another
10 minute count.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
25/89– 25 –
Components Locator Views
Fresh Food Compartment
Door Switch
Damper
LED Lights
Thermistor Location
(Continued next page)
Water Filter
Icemaker
Dispenser Water Tank
Fresh Food Evaporator Cover
Articulating Mullion Track
Fresh Food Evaporator (shown with cover removed)
Over Temperature
Thermostat
Evaporator Thermistor
Evaporator
Defrost Heater
Evaporator Fan*
*The evaporator fan is attached to theinside of the cover.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
26/89– 26 –
Freezer Compartment
Rear View
Evaporator
Defrost Heater
Evaporator Thermistor
Over Temperature
Thermostat
Light
Thermistor Location (behind light)
Compressor
Drier Condenser Fan
Condenser
Water Valve
Note:The evaporator fan is attached to theinside of the evaporator cover (not shown).
Noise Filter
Power Supply Board
Fresh Food LED Light Board
Main Control Board
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
27/89– 27 –
Control Board Connector Locator
Main Control Board
(Continued next page)
CN73 CN72 CN71 CN70
CN91
CN90
CN75CN76CN32CN30
CN50
CN78
CN10
CN10- Power Supply +5 VDC and +12 VDC Input
CN30 - FZ Door Switch, FF Left and Right DoorSwitches, FZ Sensor, FZ Defrost Sensor, FF Sensor, FFDefrost Sensor, Pantry Sensor
CN32 - Ambient Sensor, Ice Room Sensor
CN50 - Dispenser PBA Panel
CN70 - FZ Defrost Heater, FF Defrost Heater, Ice PipeHeater, French Heater, Dispenser Heater
CN71 - Compressor, FZ Room Lamp
CN72 - Icemaker Heater, Icemaker G Motor
CN73 - Ice Cover Route G Motor, Icemaker WaterValve Solenoid, Dispenser Water Valve Solenoid,Auger Motor, Cube Motor
CN75 - FZ Fan Motor, FF Fan Motor, Compressor FanMotor
CN76 - Ice Room Fan Motor
CN78 - FF LED Lights, Pantry Room Control, WaterTank Heater
CN90 - Icemaker, Icemaker Thermistor, Cycle SwitchHall Sensors
CN91 - Pantry Room Damper
Pin 1
Pin 1
Pin 1
Pin 1
Note:Looking from behind the plugs into the board, pin#1 is always on the right side.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
28/89– 28 –
Power Supply Board
Fresh Food LED Light Board
CN1
CN2
CN1 - 115 VAC Input
CN2 - Power Supply +5 VDC and +12 VDC Output
Input
Output
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
29/89– 29 –
Components
Rearranging the Shelves
To remove:
Remove all items from the shelf.
Tilt the shelf up at the front.
Lift the shelf up at the back andbring the shelf out.
To replace:
While tilting the shelf up, insert the tophook at the back of the shelf in a slot on the track.
Lower the front of the shelf until thebottom of the shelf locks into place.
Spillproof Shelves
Spillproof shelves have special edges tohelp prevent spills from dripping to lower
shelves.
Shelves in the refrigerator compartment are adjustable.
Refrigerator Compartment
Quick Space Shelf
This shelf splits in half and slides underitself for storage of tall items on the shelf below.
This shelf can be removed and replaced orrelocated (just like spillproof shelves).
Fresh Food Shelves and Bins
(Continued next page)
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
30/89– 30 –
Non-Adjustable Bins on the Door
To remove: Lift the bin straight up, thenpull out.
To replace: Engage the bin in the moldedsupports on the door and push down.It will lock in place.
Adjustable Bins on the Door
Adjustable bins can easily be carried fromrefrigerator to work area.
To remove: Lift bin straight up, thenpull out.
To replace or relocate: Slide in the bin just above the molded door supports, and pushdown. The bin will lock in place.
Non-Adjustable Dairy Bin
To remove: Lift the dairy bin straight up,then pull out.
To replace: Engage the bin in the moldeddoor supports and push down. The bin willlock in place.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
31/89– 31 –
Fresh Food Crispers and Pans
Fruit and Vegetable Crisper
Excess water that may accumulate in thebottom of the drawers or under the drawersshould be wiped dry.
Adjustable Humidity Crisper
Slide the control all the way to thehigh setting to provide high humidity recommended for most vegetables.
Slide the control all the way to the low setting to provide lower humidity levelsrecommended for most fruits.
Adjustable Deli/Produce Drawer
The Adjustable Deli/Produce Draweris a full-width drawer with adjustabletemperature control. This drawer canbe used for large miscellaneous items.
There is a temperature control which canadjust the amount of cold air allowed intothe drawer.
The control is located on the right side of the drawer.
To remove:
Pull the drawer out to the stop position.
Lift the front of the drawer up and out.
To replace:
Lift the cover up.
Engage the pantry rollers into theside rails.
Push the drawer inwards (until it is
in place).
How to Remove and Replace the Adjustable Deli/Produce Drawer
To remove:
Pull the drawer out to the stop position.
Raise the front side of the dividerto unhook it from the rear wall ofthe drawer.
To replace:
Hook the back of the divider over therear wall of the drawer.
Push the divider down.
How to Remove and Replace Drawer Divider
Control
When Produce Drawer is selected, thetemperature of the drawer can be kept around 38°F (3°C). This feature also helpskeep food fresh for a long time.
When Deli Drawer is selected, thetemperature of the drawer can be kept around 34°F (1°C). This feature also helpskeep meat or fish fresh for a longer time.
NOTE: Fruits and vegetables may be damagedusing the Deli Drawer setting. Do notstore lettuce or other leafy produce inthis drawer.
CAUTION: Do not store glass bottles in this drawer. If they are frozen, they can break and
cause personal injury.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
32/89– 32 –
Freezer Basket and Drawer
Freezer Basket and Drawer
Basket.
Drawer.
Basket Removal
To remove:
Remove Freezer Bin. (See page 8.)
Pull basket out to the stop position.
Tilt up the rear of the bin.
Lift it out to remove.
To replace:
Place the basket into the rail assembly.
To remove:
Pull the drawer out to the stop position.
Remove both side knobs with a flat-head screwdriver.
Tilt up the rear of the drawer and lift straight out.
To replace:
Pull both rails out to the stop position.
Place the drawer onto the rails andhook the support into the slots locatedon the side of the drawer.
Replace the side knob and push thedrawer back into place.
WARNING: Please do not lose the side knobs during disassembly since they may present a choking hazard to children.
Basket Divider Removal
To remove:
Pull basket out to the stop position.Tilt up the rear of the bin.
Lift it out to remove.
To replace:
Hook the top corners of the dividerover the hole of the basket.
Drawer Removal
Non-Adjustable Bins in the Freezer
To remove: Pull the brackets upward until you hear a clicking sound and removethe bin.
To replace: Hook the ends of the bin intoboth brackets and push down until the binlocks into place.
8
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
33/89– 33 –
Top Table
The top table is located on top of the refrigerator.The top table houses 2 reed switches and coversboth door hinges, ambient sensor, wire harnesses,and the dispenser water tubing disconnect. Twohinge tabs position the top table over both doorhinges and 3 screws attach it to the cabinet.
To remove the top table:
Open both doors.1.
Insert a small flat blade screwdriver under each2.of the 2 top table caps, and carefully pry themaway from the top table.
Remove the 3 recessed Phillips-head screws3.that hold the top table to the cabinet.
Pull each side of the top table up to release each4.hinge tab.
Place the top table upsidedown on top of the5.cabinet and disconnect both reed switch wireharnesses.
Cap
Top Table
Door Reed Switches and Door Magnets
The top table houses 2 reed switches, (1 for eachdoor). Each switch informs the main control boardthe status of each door, whether it is open or closed.Each switch is activated by a magnet recessed inthe top of each door.
Replacement table tops are supplied with theswitches installed. The switches are also availableseparately.
To replace the reed switches, it is necessary toremove the top table (See Top Table .) and place itinside-up on a protective surface.
Note:The reed switches may be lightly glued to thetop table. It will be necessary to carefully pry andseparate the switch from the glue.
Each reed switch is held in place by small tabs thatcan be carefully pried back.
Tab TabReed Switch
(Continued next page)
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
34/89– 34 –
Interior Lights
Freezer Light
To replace the freezer light:
Unplug the refrigerator.1.
Remove the freezer upper drawer.2. (See ControlFeatures.)
Press in on the back of the light cover then lower3.it down and out.
Replace the bulb with an appliance bulb of the4.same or lower wattage, and reinstall the lightcover.
Note:When reinstalling the light cover, make sureall top tabs snap securely in place.
Reinstall the upper drawer and plug the5.
refrigerator back in.
Refrigerator LED Light
To replace the refrigerator LED light:
Unplug the refrigerator.1.
Press in on the back of the LED light cover then2.lower it down.
Door Gaskets
The fresh food and freezer doors have magneticgaskets that create a positive seal to the front ofthe steel cabinet. The magnetic door gaskets aresecured to the doors by a barbed edge that locksinto a retainer channel.
To remove and replace the door gasket:
1. Starting at any corner, pull the old gasket out ofthe retaining channel.
2. Soak the new gasket in warm water to make itpliable.
3. Push the barbed edge of the gasket into theretainer channel.
Each door magnet is located in a recess at the topof each door. Using a small flat blade screwdriver,each magnet can be removed by carefully pryingeach side out from the recess.
Pry Pry
(Continued next page)
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
35/89– 35 –
Disconnect the LED light and the sensor wire4.harnesses.
Remove the 2 Phillips-head screws that hold3.the LED light housing to the ceiling of therefrigerator.
Remove the 2 Phillips-head screws and the LED5.board.
Fresh Food Evaporator Cover
The fresh food evaporator cover is held to the backwall of the refrigerator with a Phillips-head screwand 2 tabs.
To remove thefresh food evaporator cover:
Remove the 2 fruit and vegetable drawers and1.
the shelves that are in front of the evaporatorcover.
Using a small flat blade screwdriver, pry off the2.cap from the top of the shelf angle.
3. Remove the 2 Phillips-head screws that attachthe shelf angle to the cover.
4. Remove the 2 Phillips-head screws that hold theevaporator cover to the back wall.
Cap
Shelf Angle
(Continued next page)
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
36/89– 36 –
5. Grasp the shelf angle near the bottom and pull itout and down.
Note:Behind the cover there is a recessed area inthe back wall that houses the evaporator assembly.The top of the cover is inserted into the top of therecess and the sides have small arrows that indicate
the location of 6 tabs that lock into the recess.
Top of Recessed Area
6. Pull the cover out at the bottom, then lower thecover.
7. Turn the front of the cover towards the icemakerand disconnect the evaporator fan motor wireharness.
Disconnect
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
37/89– 37 –
Fresh Food Evaporator
WARNING:Sharp edges may be exposed whenservicing. Use caution to avoid injury. Wear Kevlargloves or equivalent protection.
The following components must be removed inthe appropriate order to access the fresh foodevaporator:
Remove the fresh food evaporator cover. (See1.Fresh Food Evapora to r Cover .)
Push in the sides of the housing cover and pull2.out the cover.
3. Disconnect the 3 fresh food evaporator defrostcomponent harnesses.
1
2
3
Defrost Components
No. Component Wire Colors
1 Bimetal Thermostat Red and Black
2 Defrost Heater Tan
3 Thermistor Yellow
Housing Cover
(Continued next page)
4. Peel off the reflective tape from the drain tray.
5. Remove the 2 Phillips-head screws that hold theevaporator to the back wall of the refrigerator.
6. Carefully pull the evaporator up to remove theheat conducting tab from the drain inlet in therecess.
Reflective Tape
Heat Tab
Freezer Evaporator Cover
The freezer evaporator cover is held to the backwall of the refrigerator with 2 recessed Phillips-headscrews.
To remove thefreezer evaporator cover:
Remove the freezer basket and drawer. (See1.Freezer Basket and Drawer .)
Remove the four 10-mm hex-head bolts (2 on2.each side) that attach the drawer front to therail assembly.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
38/89– 38 –
3. Tilt the bottom of the drawer out and lift thedrawer off the rail assembly.
4. Place the drawer front on a protected surface.
8. Lift the bottom of the cover up and pull covertowards the front of the refrigerator.
9. Disconnect the 3 freezer evaporator covercomponent harnesses.
Disconnect
Disconnect
Disconnect
Lock Tab
Note:Behind the cover there is a recessed area inthe back wall that houses the evaporator assembly.The cover is held in place by 2 recessed Phillips-head screws and 3 tabs inserted into the bottom ofthe recess.
7. Remove the 2 recessed Phillips-head screwsthat attach the cover to the back wall of thefreezer compartment.
5. Using a flat blade screwdriver, press in the raillock tab on the left side rail cover then slide therail out slightly to cover the lock tab. Repeat this
procedure on the right-side rail.
6. Evenly pull the rail assembly away from therefrigerator until both rails are clear of thecabinet.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
39/89– 39 –
3. Disconnect the 3 freezer evaporator defrostcomponent harnesses.
1
2
3
Defrost Components
No. Component Wire Colors
1 Bimetal Thermostat Red and Black
2 Defrost Heater Tan
3 Thermistor Yellow
Housing Cover
Freezer Evaporator
WARNING:Sharp edges may be exposed whenservicing. Use caution to avoid injury. Wear Kevlargloves or equivalent protection.
The following components must be removed in theappropriate order to access the freezer evaporator:
Remove the freezer evaporator cover. (See1. Freezer Evaporat or Cover .)
Push in the sides of the housing cover and pull2.out the cover.
4. Pull out the foam block from the right side of theevaporator.
5. Peel off the reflective tape from the drain tray.
6. Carefully pull the evaporator out and up toremove the heat conducting tab from the draininlet in the recess.
Heat Tab
Reflective Tape
Foam
Block
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
40/89– 40 –
Freezer Fan
The freezer fan is attached to the inside of thefreezer evaporator cover.
To remove the freezer fan assembly:
Remove the freezer evaporator cover (See1.Freezer Evapora tor Cover.) and place the cover
assembly on a protected surface so that theinside faces upward.
Note the positioning of the wiring and untape2.the wire harnesses.
3. Remove the plastic wire tie and the freezer fanwires from the retainer.
4. Remove the 4 Phillips-head screws that attachthe fan housing to the evaporator cover.
Wire
Tie
Retainer
Freezer
Fan
Replacing Evaporators Using the LOKRINGMethod
Fresh Food Evaporator
Parts Needed:
Fresh Food Evaporator•
Drier Assembly•
Access Tube (part # WJ56X61)•LOKRING• Connectors- (part # WR97X10031)
(part # WR97X10085)
(part # WR97X10021)
Freezer Evaporator
Parts Needed:
Freezer Evaporator•
Drier Assembly•
Access Tube (part # WJ56X61)•
LOKRING• Connectors- (2 of part # WR97X10021)
The LOKRING method provides a durable, vibrationresistant compression connection for both copperand aluminum tubing. The connectors can be usedwithin a temperature range of -58°F (-50°C) to+302°F (150°C) and showed to have a higher burststrength than that of the tube itself. Refer to ServiceGuide #31-9067 for complete instructions on usingthe LOKRING method of installing an evaporator.
(Continued next page)
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
41/89– 41 –
5. Remove the fan housing and place it blade sideup on the protected surface.
Note:An anti-slip adhesive is applied to the fanblade hub during factory assembly and the fanblade may be dif ficult to remove.
6. Using 2 large flat blade screwdrivers, placeeach screwdriver under the fan blade hub, 180°
apart, and over 2 opposite legs of the housingas shown. Carefully pry up and remove the fanblade from the motor shaft.
7. Remove the 2 Phillips-head screws, then rotatethe fan motor 90° counterclockwise and removethe motor from the fan housing.
Leg (1 of 4 )
Retainer
Ice Room Blower
The ice room blower is attached to the inside of thefreezer evaporator cover.
To remove the ice room blower assembly:
Remove the freezer evaporator cover (See1.Freezer Evapor at or Cover.) and place the cover
assembly on a protected surface so that theinside faces upward.
Note the positioning of the wiring and untape2.the wire harnesses.
Remove the 2 plastic wire ties (not shown) and3.the blower wires from all retainers.
Remove the 4 Phillips-head screws that attach4.the blower housing to the evaporator cover.
Ice Room Blower Assembly
(Continued next page)
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
42/89– 42 –
5. Remove the blower housing and place it blowerwheel-side up on the protected surface.
Note:An anti-slip adhesive is applied to the blowerwheel hub during factory assembly and the blowerwheel may be dif ficult to remove.
6. Firmly grasp the blower wheel and pull it off themotor shaft.
7. Remove the 2 Phillips-head screws then rotatethe blower motor 90° counterclockwise andremove the motor from the blower housing.
Reflective Tape
Masking Tape
Note:The fan blade may be dif ficult to removefrom the motor shaft. Care must be taken to avoid
damage to the fan blade and/or fan housing.
4. Place the fan housing blade side up on aprotective surface.
5. Using 2 large flat blade screwdrivers, placeeach screwdriver under the fan blade hub, 180°apart, and over 2 opposite legs of the housingas shown. Carefully pry up and remove the fanblade from the motor shaft.
Screwdriver
Screwdriver
Fresh Food Fan
The fresh food fan motor is attached to the inside ofthe fresh food evaporator cover.
To remove the fresh food fan:
Remove the fresh food evaporator cover. (See1.Fresh Food Evapora tor Cover .)
Peel off the masking tape from the top and the2. reflective tape from the bottom of the fan motorhousing.
Remove the 4 Phillips-head screws that attach3.the fan housing to the evaporator cover.
Leg (1 of 4 )
(Continued next page)
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
43/89– 43 –
6. Remove the 2 Phillips-head screws, then rotatethe fan motor 1/4-turn counterclockwise andremove the motor from the fan housing.
Machine Compartment Cover
The machine compartment cover is held to the rearof the refrigerator with 8 Phillips-head screws and 2tabs. After removing the screws the cover can thenbe lifted from the tabs.
Tab
Note:When installing the machine compartmentcover, be sure to place the cover over the 2 tabsbefore installing screws.
Condenser Fan
The condenser fan motor is mounted in the machinecompartment between the compressor and thecondenser. The machine compartment cover mustbe properly installed to ensure air passes throughthe condenser. (See Machine Compa rtment Cover .)
Condenser Fan Parameters
Disconnect
Front Tab
Room Temperature Condenser Fan Operation
Above 66°F Fan operates withcompressor.
61 - 65°F Fan has 5-minute delay,then operates with
compressor.
Below 60°F Condenser fan does notoperate at all.
To remove the condenser fan:
Remove the machine compartment cover. (See1.Machine Compart ment Cover .)
Disconnect the fan wire harness.2.
Using a flat blade screwdriver or fingertip,3.simultaneously lift the front tab of the fanhousing and pull the fan assembly outapproximately 1 inch.
(Continued next page)
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
44/89– 44 –
4. Rotate the fan assembly clockwise thencarefully maneuver the fan assembly out of themachine compartment.
5. Using a flat blade screwdriver, remove thespring clip.
6. Pull the fan blade off the motor shaft.
Spring Clip
8. Remove the 2 Phillips-head screws from the fanhousing.
9. Using a flat blade screwdriver or fingertips, liftand spread each of the 2 tabs on the motorclamp and pull the fan motor out of the housing.
7. Note the routing of the wiring through theretainers and the position of the motor andclamp. Remove the wiring from the retainers.
Retainer
Retainer
Retainers
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
45/89– 45 –(Continued next page)
Note:To accurately test a thermistor, place thethermistor in a glass of ice water (approximately
33°F (0.5°C)) for several minutes and check forapproximately 12.7K Ω.
Thermistor Resistance
Temperature(°F)
Temperature(°C)
Resistance in Kilo-Ohms
-40 -40 88 kΩ
-31 -35 67.6 kΩ
-22 -30 52.4 kΩ
-13 -25 40.9 kΩ
-4 -20 32.2 kΩ
5 -15 25.6 kΩ
14 -10 20.4 kΩ
23 -5 16.4 kΩ
32 0 13.2 kΩ
41 5 10.8 kΩ
50 10 8.9 kΩ
59 15 7.3 kΩ
68 20 6.1 kΩ
77 25 5 kΩ
86 30 4.2 kΩ
95 35 3.5 kΩ
104 40 3 kΩ
113 45 2.5 kΩ
122 50 2.2 kΩ
131 55 1.9 kΩ
140 60 1.6 kΩ
Thermistors Fresh Food Thermistor
The fresh food thermistor is inserted in a recesslocated in the back of the fresh food LED lighthousing.
To access the thermistor it is necessary to removethe LED light housing. (See Interior Lights .)
The thermistor recess is covered with a foaminsulator that must be peeled back to remove thethermistor.
Thermistor
Foam Insulator
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
46/89– 46 –
Freezer Thermistor
The freezer thermistor is inserted in the thermistorcover located in the ceiling of the freezercompartment behind the light. To access thethermistor it is necessary to remove the freezerbasket and drawer. (See Freezer Basket and Drawer .)
To remove the thermistor cover, insert a flat blade
screwdriver under the cover and gently pry thecover from the ceiling.
The thermistor is connected to the refrigerator witha wire harness.
Thermistor
Thermistor Cover
Disconnect
(Continued next page)
Fresh Food Evaporator Thermistor
To access the fresh food evaporator thermistor thefresh food evaporator cover must be removed. (SeeFresh Food Evapora tor Cover .) The housing cover canbe removed to disconnect the wire harnesses to the
thermistor. (See Fresh Food Evapor at or .)
The fresh food thermistor is located on the
evaporator inlet tube.The thermistor wiring is attached to the evaporatorwith 2 plastic wire ties and is held to the inlet tubewith a plastic clamp. The 2 tabs on the clamp can bepried open to release the thermistor.
Tab
TabThermistor
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
47/89– 47 –
Freezer Evaporator Thermistor
To access the freezer thermistor the freezerevaporator cover must be removed. (See FreezerEvapor at or Cover .) The housing cover can beremoved to disconnect the wire harness to thethermistor. (See Freezer Evapor at or .)
The freezer thermistor is located in a plastic holder
attached to the evaporator.The thermistor holder and the thermistor wiringare attached to the evaporator with 3 plastic wireties. After the plastic wire ties are removed, thethermistor can be pulled out of the holder.
Thermistor
Holder
Ice Room Thermistor
The ice room thermistor is inserted in the augermotor cover. To replace the ice room thermistor theauger motor assembly must be removed. (See AugerMotor Assembly .)
The thermistor is connected to the auger motorassembly with a wire harness.
Thermistor
(Continued next page)
Pantry Thermistor
The pantry thermistor is inserted in the dampercover.
To replace the pantry thermistor:
Remove the damper assembly1. . (See DamperAssembly .)
Peel off the foam that seals the damper cover to2.the back wall of the refrigerator.
3. Carefully pull out the damper assembly from thedamper cover.
Foam Seal
4. Pull out the pantry thermistor from the dampercover.
Thermistor
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
48/89– 48 –
Ambient Thermistor
The ambient thermistor is located under the rightside of the top table.
To replace the ambient thermistor:
Note:In the following step you do not need todisconnect both reed switch wire harnesses.
Remove the top table1. . (See Top Table .)
Cut off the thermistor leads where they enter2.the thermistor body.
3. Use plastic bell connectors and fill theconnector with RTV102 silicone then splice anew thermistor into the wires as shown in theillustration.
RTV102
Thermistor
C u t H e r e
C u t H e r e
Over Temperature Thermostats
Fresh Food Over Temperature Thermostat
The over temperature thermostat is attachedon a bracket located on the top left side of theevaporator. (See Component Locator Views .)
The thermostat wiring is attached to the evaporator
with 2 plastic wire ties and the thermostat is heldto the bracket with a metal clip. It is necessaryto remove the FF evaporator from the recess toreplace the over temperature thermostat. (See FreshFood Evapor at or .)
Bracket
Metal Clip
Over Temperature
Thermostat
Left Side View of Evaporator
Freezer Over Temperature Thermostat
The over temperature thermostat is attachedon a bracket located on the top right side of theevaporator. (See Component Locator Views .) Thethermostat wiring is attached to the evaporatorwith a plastic wire tie and the thermostat is held tothe bracket with a metal clip.
Top Right View of Evaporator
Over Temperature
Thermostat
Bracket
Metal Clip
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
49/89– 49 –
Defrost Heaters
Fresh Food Defrost Heater
The defrost heater is located on the sides andbottom of the evaporator.
The defrost heater wiring is attached to theevaporator with 4 plastic wire ties and the heater is
held in 2 slots (1 on each side) at the bottom of theevaporator.
To remove the defrost heater:
Carefully bend open the tabs that form the 21.slots and pull down the heater.
Carefully pull the bottom of the evaporator2.approximately 45 degrees from the recess.
Tab
Defrost Heater
Drain Tray
S l o t
(Continued next page)
3. Using a small flat bladed screwdriver, reachbehind the drain tray and bend straight the 4lock tabs that hold the evaporator to the draintray.
4. Separate the drain tray from the evaporator.
5. Remove the defrost heater from the evaporator.
Note:When installing the heater to the drain tray,be sure heat tab is inserted into the drain tray outlet
Rear View of Drain Tray
Lock Tab (1 of 4)
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
50/89– 50 –
Freezer Defrost Heater
The defrost heater is located on the sides andbottom of the evaporator.
The defrost heater wiring is attached to theevaporator with 4 plastic wire ties and the heater isheld in 4 slots) at the bottom of the evaporator.
To remove the defrost heater:
Remove the 4 plastic wire ties.1.
Remove the foam air block.2.
3. Peel off the reflective tape.
4. Carefully bend open the tabs that form the 4slots and pull down the heater.
5. Carefully pull the evaporator out and up toremove the heat conducting tab from the draininlet in the recess.
Tab
Heat Tab
Reflective Tape
S l o t
Foam Air Block
(Continued next page)
6. Using a small flat bladed screwdriver, reachbehind the drain tray and bend straight the 2lock tabs that hold the evaporator to the draintray.
7. Separate the drain tray from the evaporator.
8. Remove the defrost heater from the evaporator.
Note:When installing the heater to the drain tray,be sure heat tab is inserted into the drain tray outlet.
Rear View of Drain Tray
Lock Tab (1 of 2)
Duct Heater
The duct heater is attached to the inside of thefreezer evaporator cover. The duct heater preventswater from freezing and blocking air flow to the iceroom.
The duct heater is in a parallel circuit with thefreezer defrost heater. The heaters are in series withthe bimetal defrost safety thermostat. Both heatersoperate at 120 VAC when the freezer defrost circuit
is energized by the main control board and thedefrost safety thermostat is closed.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
51/89– 51 –
Retainer
To remove the duct heater:
Remove the freezer evaporator cover (See1.Freezer Evapor at or Cover.) and place the coverassembly on a protected surface so that theinside faces upward.
Note the positioning of the wiring and untape2.the wire harnesses.
Remove the 2 plastic wire ties (not shown) and3.
the duct heater wires from all retainers.
Duct HeaterWire Harness
The heater can be checked directly as a separatecomponent by removing the freezer evaporatorcover (See Freezer Evapora tor Cover .) The heater wireharness can then be disconnected.
The duct heater has a resistance value ofapproximately 3.18K Ω.
(Continued next page)
4. Press inward the top and bottom tabs and pullthe duct assembly from the ice room blowerhousing.
Bottom Tab
Top Tab
Top View of Duct Bottom View of Duct
EMI Filter and Power Cord
It is necessary to remove the EMI filter to replace thepower cord. The power cord is connected to the EMIfilter with a wire harness.
To remove the EMIfilter and power cord:
Remove the machine compartment cover. (See1.Machine Compa rtment Cover .)
Remove the Phillips-head screws that hold the2.EMI filter bracket, water valve, power cord, andground wires to the cabinet.
Disconnect the EMI filter wire harness.3.
Disconnect
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
52/89– 52 –
4. Position the water valve to the left side.
5. Pull the EMI filter bracket straight out.
6. Using a flat blade screwdriver, press in the 2tabs and open the bracket.
7. Disconnect the power cord wire harness.
8. Remove the 13 mm. hex nut and ground wirefrom the filter.
Disconnect
13 mm. Hex Nut
Ground Wire
PTCR Relay, Run Capacitor, and OverloadAssembly
The PTCR relay, run capacitor, and overloadassembly is held to the compressor by 2 legs at thebottom and a lock tab at the top.
To remove the PTCR relay, run capacitor, andoverload assembly:
Remove the machine compartment cover. (See1.Machine Compa rtment Cover .)
Disconnect the PTCR relay, run capacitor, and2.overload wire harness.
3. Using a flat blade screwdriver, press in thelock tab on top of the assembly and rotate theassembly counterclockwise.
Disconnect
Lock Tab
Compressor
The compressor is a reciprocating type. Refer to themini-manual for the BTU/hour rating, refrigeranttype, and correct charge for this model. A 1/4-in.O.D. copper tube is provided for access to the lowpressure side of the refrigeration system.
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
53/89– 53 –
Dispenser Display Assembly
The dispenser display assembly incorporates theinterface used for temperature control and featuresand houses the dispenser LED lights. The display has6 tabs that hold it to the dispenser recess.
To remove the dispenser display:
Remove the Phillips-head screw from the1. housing.
2. Insert a small flat-blade screwdriver into thesmall opening located at the bottom frontcorner of the display.
3. Pry the bottom right side of the dispenserdisplay away from the dispenser recess.
4. Grasp display, pull it towards the right andremove it from the recess.
5. Disconnect the wire harness.
Caution:To prevent breaking tabs when installingthe display, first insert the left side tabs into therecess then snap the display in place.
Disconnect
loaded from www.Manualslib.com manuals search engine
http://www.manualslib.com/http://www.manualslib.com/
-
8/16/2019 PFSS6NKW GE Refrigerator Service Manual
54/89– 54 –(Continued next page)
Dispenser Assembly
The dispenser assembly includes the duct door, ductdoor motor, cam and cam switches, and funnel.The assembly is held to the dispenser recess with 2screws and 1 tab.
To replace the dispenser display:
Remove the dispenser display assembly. (See1.Dispenser Display Assembly .)
Disconnect the motor and cam switches wire2.harnesses.
Remove the 2 Phillips-head screws. Lower the3.assembly down to disengage the tab and pullthe dispenser assembly from t