Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing...
Transcript of Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing...
![Page 1: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/1.jpg)
0
Perspectives on Advanced Manufacturing Technology University Turbine Systems Research Workshop
Atlanta, GA
Turbomachinery Design and Development CenterHanwha Techwin
Houston, TXKarl D. Wygant
November 2, 2015
![Page 2: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/2.jpg)
1
Process & Gas Compressors
AirCompressors
Gas Turbine &Compressor
Packages
Turbo-Compressors
Over 30 years experience of compressor technology originally derived from gas turbine business...
Power Systems Division is Manufacturer of Wide Range of Turbomachinery Products
Turbomachinery Products Designed for Diverse Applications
![Page 3: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/3.jpg)
2
Aero-Mechanical Optimization of Turbomachinery
![Page 4: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/4.jpg)
3
Influence of Manufacturing Technology on Turbomachinery Design
Goals for commercial gas turbines and compressors are consistent …
Increasing efficiency Increasing reliability Decreasing maintenance cycle Reduced delivery time
Each manufacturer has slightly different approach …(but all really based on similar philosophies)
Discussed herein is the following …
OEM’s approach to turbomachinery optimization How additive manufacturing can alter that paradigm significantly. Example case to illustrate the impact additive manufacturing can have on
turbomachinery design.
End users drive need for reduced OPEX
Competition amongst OEM’s fosters lower CAPEX
Regulations drive reduced environmental impact
![Page 5: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/5.jpg)
4
Within Turbomachinery Multiple Engineering Disciplines are All Coupled
FEA - Stress
CFD - Flow
Rotor-Bearing Dynamics
Cooling
![Page 6: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/6.jpg)
5
Example … in part from Joint Program between Hanwha Techwin and Southwest
Research Institute
![Page 7: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/7.jpg)
6
DMLS in Turbomachinery
Stationary and rotating parts
Published application of DMLS to rotating parts limited mostly to development test rigs
100,000 rpm 1380 °F Inconel GT wheel (Inconel 718)SwRI experience with micro-turbomachine closed impellers
and turbinesOverspeed test successful at 1140 ft/sOverspeed test to failure at 1403 ft/s
Flow Straightener for Helicopter Engine (Killian 2013)
100 krpm GT wheel (Killian 2013)
EOSINT M 280 (Source: EOS)
![Page 8: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/8.jpg)
7
DMLS Impeller Design Considerations
The Direct Metal Laser Sintering process works best to minimize material…- Thicker parts can build internal stresses that lead to fracture during build process.- Excellent rotordynamic characteristics as weight and inertia are minimized.- Reduced material minimizes build time and cost.
Ribbed Design Produces Non-uniform Seal Clearance and High Stresses in Ribs – Tested Inconel 718 Part Instead
![Page 9: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/9.jpg)
8
Tensile Test Results DMLS Ti 6AL-4V
0
5
10
15
20
25
30
0
200
400
600
800
1000
1200
spec 1 2 3 4 5 6
Yield σ(Mpa)Peak σ(Mpa)Elongation(%)
Under 200 X magnification micro-porosity is present: Investigated implication on fatigue strength Investigate dimensionality
Reduced grain size: Slight increase in yield and ultimate strength Increased material hardness
![Page 10: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/10.jpg)
9
Test Results Show Reduced Fatigue LifeS-N Diagram for DMLS Ti 6AL-4V
Reduced Fatigue Strength
![Page 11: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/11.jpg)
10
Manufacturing Flexibility Significantly Outweighs Fatigue LimitDMLS Ti 6AL-4V
Peak Stress Concentration
DMLS
Braze
EB Weld
15% decrement due to strength
35% reduction in stress due to increased design flexibility.
![Page 12: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/12.jpg)
11
Relationship to Integrally Geared sCO2
![Page 13: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/13.jpg)
12
Advanced 10 MWe Integrally Geared Compressor-Expander Configuration
Expanders
Compressors
Re-Compressors
Generator
Technology Demonstrator
Advanced Impeller Concepts
Generator
Turbine Gea
rbox
Re-
Com
pres
sor
Com
pres
sor
![Page 14: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/14.jpg)
13
Conclusions and Future Needs
![Page 15: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/15.jpg)
14
Conclusion
Advantages of Direct Metal Laser Sintering:
Process lends it self to reduced material waste Process lends itself to minimizes weight … improved rotordynamics. Process removes some previous constraints … can reduce “effective” stress and improve component
life. Or with lower effective stresses it becomes possible to re-stagger the design optimization and achieve
high efficiency and/or high compressor ratios.
Opens Up New Design Possibilities:
Can we build in new and advanced forms of integrated blade damping mechanisms ? Can we develop internal flow paths that were not feasible before? Add ability to add internal cooling pssages in novel ways
![Page 16: Perspectives on Advanced Manufacturing Technology · Perspectives on Advanced Manufacturing Technology . University Turbine Systems Research Workshop. Atlanta, GA. Turbomachinery](https://reader033.fdocuments.us/reader033/viewer/2022052720/5f09b66f7e708231d4282825/html5/thumbnails/16.jpg)
15
Going Forward
Some of the practical issues facing OEM:
Inspections …
QA practices are lagging technology. Technology allows ability design components with
internal structures that are difficult to inspect.
Material Properties …
Fatigue properties are key to design process.Some vendors are using “propriety” powder blends
Build Process …
Fractures can develop during build process. Surface roughness has drastically reduced. Substantial post build work required.