Series PCHG Gas Filtration Products

USA Patent No. 5827430 and 5893856 (International Patents Granted)

E N G I N E E R E D F I L T R A T I O N S O L U T I O N S ®

ISO 9001

®

FS-PCHG-SL.qxd:EL-PCHG-SL-01 PEACH rev 8/31/10 3:19 PM Page 2

The PEACH®

Conical HelixStructureyields high flowand maximumefficiency.

THE PEACH®

The PEACH® consists of severallateral sections of PEM formedinto a conical helix pattern. Eachsection consists of multiple helicalywrapped layers. Through thermalbonding, these spiral layers areapplied to conform and overlapthe previous layer, forming acone…the conical helix structure.This structure results in a gradeddensity pattern that yields highcontaminant loading, structuralstrength, maximum efficiency, andexcellent reproducibility.

GRADED DENSITYEach layer of the PEACH® filterperforms a particular function.While all layers are designed to aspecific micron rating, each lateralsection removes contaminants.The outer layer typically removesthe bulk solids. As contaminantsmove through the depth of thecone, the filter densities increaseto meet increase to meet therequired micron rating. The innerlayers of the filter providestructural strength.

Peach Media 150XSEM Photo by Southwest Research Institute

PEACH® FILTRATION TECHNOLOGY

•A performance engineered cartridge•Predictable performance•Performance assured from start-up

•No unloading•High dirt holding capacity•No media migrationENVIRONMENTAL FEATURES

•100% synthetic

•Incinerable — (CO2 + Water) Trace ash & no plastic residue

•Ease of disposal: crush, shred, chop, etc.•Coreless, no metal parts•No fiberglass media

PECO® ENGINEERED MEDIAPEM, specifically designed forfiltration coalescing, is the keycomponent in the production ofthe PEACH® gas element. The PEMis designed with an assignedmicron rating and efficiency. Rawfibers of various denier areweighed, blended and thermallybonded, then formed into acompressed filter media sheet.Various layers of PEM are thenused in the manufacture of thePEACH® gas element.

PECO® ENGINEERED APPLIED

CONICAL HELIX TECHNOLOGY

PEACH® is the manufacturingprocess incorporating PEM toform an element into a conicalhelix. This innovative patentedprocess makes possible agraded density pattern whichyields outstanding filtration.

PEACH® F ILTRATION TECHNOLOGYgives you consistent, predictable performance,high contaminant loading, and high efficiency.

PEACH® - an innovative gas filtering/coalescing technology.

FS-PCHG-SL.qxd:EL-PCHG-SL-01 PEACH rev 8/31/10 3:20 PM Page 3

CONSTRUCTION

•Media Polyester or Polypropylene

•Gaskets/End Cap Integral thermally bondedpolyester or polypropylene.Optional buna-n or viton withmetal end caps.

•Core None in standard construction.If required — louvered,carbon steel.

OPERATIONAL DATA

•Recommended Element Change Out:12 - 14 PSID / .83 - .97 bar.

•See chart below for collapse strengths

•Maximum Operating Temp:Polyester 240º F / 116º CPolypropylene 180º F / 82º CNote: Temps from 200º - 240ºF require a corefor 4.5” & 5.5” O.D. filters.

•Micron Ratings:0.5, 1, 5, 10 SCW=0.3

•Recommended Torque to Seal Filters: 5-10 ft-lbsNOTE: This Torque should not be exceeded.

PRODUCT ADVANTAGES

• PEACH® element has a high densitytube with tolerances of +/- 5%, ascompared to fiber glass tubes withtolerances of +/- 15%

• Integral end cap serves as gasket =60 Durometer

• Long shelf life on elements withoutcores

• Resistant to erosion at high velocities

• Direct replacement to standardFiberglass element

• Cylindrical elasticity eliminatescollapsing on element carrier

• Multiple bonded layers for strengthand rigidity

• Graded density for higher dirt loadingand coalescing efficiencies

• Hydrophilic and oliophilic materialsmeans greater coalescing efficienciesat higher rates

• No binders or glues for more directchemical compatibility

I SO 9001 CERT IF ICAT IONPECO® Filtration Elements are manufactured

under a quality management system certified to

ISO 9001. This assures that each PECO® Filter is

engineered and manufactured to the highest level

of quality standards therefore assuring you consis-

tent tolerances and quality…filter after filter!

CORE COLLAPSE STRENGTHS: PSID

Size

3”

4.5”

5.5”

Temp ºF100150200100150200100150200

No Core4035203025N/RN/AN/AN/A

STD CoreN/AN/AN/A505050353535

High PressureCore

N/AN/AN/A145145145N/AN/AN/A

N/R = Not RecommendedN/A = Not Applicable

Notes:1. Polypropylene is recommended in filter/separators which aredownstream of an amine processing plant due to possible contactwith carryover amine fluids.

2. It is recommended that a core be used in the PCHG elementswhen retrofitting into some vessels other than PECO.PECO vessels incorporate a full length element z-bar carrier tosupport the element and therefore do not require a core in thestandard 4.5” O.D. filters.

3. Refer to “Core Reference Chart” on back page to determine if coresare available as standard.

PEACH® GAS ELEMENTS

FS-PCHG-SL.qxd:EL-PCHG-SL-01 PEACH rev 8/31/10 3:20 PM Page 4

W/CoreStandardStandardStandard

W/O CoreN/AN/AN/A

StyleAll KPCHGAll PPCHGAll BPCHC (S)

PCHG NOMENCLATURE CHART

AVAILABLE MODELS The PCHG is a direct replacement to the PECO® FG gas element. *Comparisons illustrated for 1 Micron Elements

Length(in/mm)12/30424/60936/91472/182812/30424/60936/91472/182836/91472/1828

OD(in/mm)3/763/763/763/764.5/1144.5/1144.5/1144.5/1145.5/1395.5/139

ID(in/mm)2.08/532.08/532.08/532.08/53

3.125/79.383.125/79.383.125/79.383.125/79.384.25/1084.25/108

ModelPCHG-12PCHG-24PCHG-36PCHG-72PCHG-312PCHG-324PCHG-336PCHG-372PCHG-536PCHG-572

PCHG Dirt Loading(lbs/gms).71/3231.50/6842.24/10214.43/20201.17/5332.33/10623.50/15967.00/31924.27/19478.11/3698

FG Dirt Loading(lbs/gms).70/3191.45/6612.2/10034.4/20061.05/4782.09/9533.14/14316.28/28633.83/17487.67/3496

CORE REFERENCE CHART

W/CoreN/AN/A

OptionalStandardStandardStandardStandardStandard

W/O CoreStandardStandardStandardN/AN/AN/AN/AN/A

StylePCHG 3” O.D.PCHG SCW 3” O.D.PCHG 4.5” O.D.PCHG 4.5” O.D., 5 & 10µPCHG 5.5” O.D., 5 & 10µPCHG 5.5” O.D.PCHG SCW 4.5” & 5.5” O.D.PCHG A 3”, 4.5” & 5.5” O.D.

N/A = Not Applicable

*Above results are based on standard PECO® testing protocol.

Please refer to pecofacet.com for most current literature edition.

Corporate Headquarters

PO Box 640Mineral Wells, Texas 76068Ph: 800-877-7326

940-325-2575Fax: 940-325-4622E-Mail: elements@pecofacet.com

perryequipment.com

Locations

Almere, The NetherlandsCafasse (Torino), ItalyCalgary, CanadaEvansville, WyomingFarmington, New MexicoGreensboro, North CarolinaHouston, TexasKempen, GermanyKuala Lumpur, MalaysiaLa Coruna, SpainManama, BahrainMid Glamorgan, United KingdomPorto Alegre, BrazilQueretaro, MexicoRoissy (Paris), FranceSacramento, CaliforniaShanghai, ChinaStilwell, OklahomaTulsa, OklahomaVernal, UtahWeifang, China

Your local distributor:

EL-PCHG-SL-01 (LHA 8/10)

Brought to you by

*

*See core reference chart as applicable.

FS-PCHG-SL.qxd:EL-PCHG-SL-01 PEACH rev 8/31/10 3:19 PM Page 1