Performance Data - Model PTCmodine.com/download/1/6-114.pdf · COMBUSTIO AIR LOUERS (HD OLY) 3 3 3...
Transcript of Performance Data - Model PTCmodine.com/download/1/6-114.pdf · COMBUSTIO AIR LOUERS (HD OLY) 3 3 3...
HOT DAWG™ POWER-EXHAUSTED, GAS-FIRED UNIT HEATER (MODEL HD)• Hush-puppy quiet operation (see table)
• Right or left hand controls available on all 30-75 units. Gas, electrical and flue connections can be changed by simply flipping the unit over
• Uses natural or propane gas
• Lightweight, easily installs 1” from ceiling with only two angle brackets (included on sizes 30-75, accessory for 100, 125)
• Full 10-year warranty on heat exchanger
• Standard power exhaust simplifies side-wall or roof venting with small-diameter vent pipe
• Permanently-lubricated motor for trouble-free dependability
• Controls can be either single or two-stage, direct spark ignition, 100% shut-off with continuous retry
• Low-profile design and neutral color to blend in with decor
• Also available with a blower (model HDB). Contact Modine for further information
HOT DAWG™ SEPARATED COMBUSTION GAS-FIRED UNIT HEATER (MODEL HDS) Same features as HD, with these added benefits:• Draws combustion air from outside the work space,
ensuring the unit always has plenty of fresh, clean air to breathe
• The fresh air supply reduces common concerns about dusty, dirty or humid applications, providing greater durability and reduced maintenance
• Factory assembled, certified separated combustion saves installation time
HOT DAWG™ H2O LOW PROFILE HOT WATER UNIT HEATER (MODEL HHD)
• No external moving parts - twin centrifugal blowers keep all moving parts inside the cabinet
• Mounting flexibility (parallel, perpendicular or recessed between joists) allows for horizontal or vertical air delivery
• Low-profile design
• Available in hammertone beige
• Constructed of heavy gauge steel for clean appearance and maximum headroom
• Includes two mounting brackets with vibration isolators to reduce noise and vibration
• Internal coil can handle water pressures up to 150 PSI and temperatures up to 200° F
Horizontal air delivery; perpendicular to joists
Vertical air delivery; recessed between joists
Horizontal air delivery; parallel to joists
Hot Dawg H2O Mounting Flexibility
Hot Dawg H20 Applications
Model Sizes Airflow (CFM) GPM 140° F
BTU/hr180° F BTU/hr Application
HHD 30 405 405
24
20,600 24,200
30,90036,300 1 to 2 car garage
HHD 45 (high speed) 710 710
24
29,900 35,100
44,80052,700 2 to 3 car garage
HHD 45 (low speed) 425 425
24
20,700 24,400
31,10036,600 2 to 3 car garage
YEAR-ROUND COMFORT TO WORK, PLAY AND RELAX
Hot Dawg ApplicationsModel Btu/Hr Input Typical Application
HD/HDS 30 30,000 1 to 1-1/2 Car Garage
HD/HDS 45 45,000 2 to 2-1/2 Car Garage
HD/HDS 60 60,000 3 to 3-1/2 Car Garage
HD/HDS 75, 100, 125 75,000-125,000 Large Garage
*Sizing data for sample only. Consult a qualified installer for the actual requirements for your building.
Model HD/HDS Sound Pressure Level (dBA)1
ModelSize
Modine Competitor2
5 ft. 5 ft.
30 53 59
45 57 59
60 59 59
75 58 69
1. Measured at distance from unit shown. 2. Competitor published data.
Performance Data - Model HD/HDSModel Size 30 45 60 75 100 125
Btu/Hr Input1 30,000 45,000 60,000 75,000 100,000 125,000
Btu/Hr Output1 24,000 36,000 48,000 60,000 80,000 100,000
Entering Airflow (CFM)2 505 720 990 1,160 1,490 1,980
Outlet Velocity 2 523 749 653 769 565 747
Air Temp. Rise (ºF) 44 46 45 48 50 47
Mounting Height (Max ft.) 2 10 10 12 14 12 16
Heat Throw (ft.) 25 27 36 38 42 56
Hot Dawg H20 Applications
Model Sizes Airflow (CFM) GPM 140° F
BTU/hr180° F BTU/hr Application
HHD 30 405 405
24
20,600 24,200
30,90036,300 1 to 2 car garage
HHD 45 (high speed) 710 710
24
29,900 35,100
44,80052,700 2 to 3 car garage
HHD 45 (low speed) 425 425
24
20,700 24,400
31,10036,600 2 to 3 car garage
Dimensions (inches) - Model HD/HDSModel Size 30 45 60 75 100/125
A 26.8 26.8 26.8 26.8 35.5
B 12.2 12.2 18.0 18.0 20.5
C 22 22 25 25 31.0
Gas Connection 1/2 1/2 1/2 1/2 1/2
Vent Connector Size (in.) 3 3 3/4* 3/4* 4
Approx. Shipping Weight (lbs.) 55 60 80 85 125
* 3” for Model HD, 4” for Model HDS
HOT DAWG™ SPECIAL EDITION BLACK UNITS• Units are available in propane or natural gas
• Sizes: HD30, HD45, HD60 and HD75
• Available in satin black or standard green
• Perfect for single to four-plus car garages
• Available with standard power vent only (Not available with stainless steel exchanger or separated combustion)
Huntin’ Dawg
Carbon Fiber
Diamond Dawg
1” - angle, mounting brackets are slotted to accommodate joists on 16” or 24” centerlines.
Top and Bottom 1" 1" Access Side 1" 18" Non-Access Side 1" 1" Rear 18" 18" Vent Connector 4" 4"
30 45 60 75 100 12530,000 45,000 60,000 75,000 100,000 125,00024,000 36,000 48,000 60,000 80,000 100,000
505 720 990 1,160 1,490 1,980523 749 653 769 565 747
44 46 45 48 50 47 10 10 12 14 12 16 25 27 36 38 42 56 1/15 1/15 1/12 1/12 1/12 1/8 1,550 1,550 1,625 1,625 1,050 1,550 S.P. S.P. P.S.C. P.S.C. S.P. P.S.C. 2.4 2.4 1.2 1.2 2.7 2.2 3.7 3.7 2.5 2.5 4.7 4.2
* 3" for Model HD, 4" for Model HDS
Model SizeBtu/Hr Input
Btu/Hr OutputEntering Airflow (CFM)
Outlet VelocityAir Temp. Rise (°F)
Mounting Height (Max ft.)Heat Throw (ft.)
Unit Total Amps
3/4* 3/4* 4Vent Connector Size (in.)
Performance
HorsepowerRPMTypeAmps
MotorData
Mounting
ClearancesUnit Side Clearance To
Combustible MaterialsRecommended
Service Clearance
SIZES30-75
SIZES100/125
(ACCESSORY)
.00
1.10
3.10
5.10
7.10
9.10
17.1
0
19.1
0
21.1
0
23.1
0
25.1
026
.20
.00
1.50
3.50
5.50
7.50
9.50
11.5
0
13.5
0
21.5
0
23.5
0
25.5
0
27.5
0
29.5
0
31.5
0
33.5
035
.00
30 45 60 75 100/125 26.8 26.8 26.8 26.8 35.5 12.2 12.2 18.0 18.0 20.5 16.5 16.5 16.5 16.5 22.0 14.9 14.9 14.9 14.9 22.5 10.1 10.1 15.9 15.9 18.4 7.25 7.25 10.75 10.75 14.0 18.5 18.5 18.5 18.5 24.0 7.6 7.6 7.835 7.835 8.4 1/2 1/2 1/2 1/2 1/2 34.5 34.5 34.5 34.5 43.0 22 22 25 25 31.0 2.74 2.74 3.15 3.15 3.87 3.19 3.19 5.55 5.55 10.73
10 10 14 14 18.0 55 60 80 85 125
Model SizeABCDEFGH
Gas ConnectionIJK (HDS only)L (HDS only)
Fan DiameterApprox. Shipping Weight (lbs.)
Dimensions (inches)
Control Options Control Description Control Service Thermostat Type of Model Code No. Voltage Voltage Gas Size
Single-Stage, Direct Spark Ignition, 100% Shut-Off with Continuous Retry 11 115V 24V natural 30-125- Utilizes a single-stage combination gas control with ignition control. Gas is lit with a direct spark igniter on call for heat. 21 115V
24V
propane
30-125
Two-Stage, Direct Spark Ignition, 100% Shut-Off with Continuous Retry 12 115V 24V natural 75-125- Utilizes a two-stage combination gas control with built-in ignition control. Firing rate is 100% and 50% of full rated input. Gas is lit with a direct spark 22 115V 24V propane
75-125igniter on call for heat.
COMBUSTION AIRLOUVERS (HD ONLY)
3 3
3 3
4 4 4Combustion Air Inlet ConnectorSize (Model HDS only) (in.)
B
A
CC (APPROX.)
1” - angle, mounting brackets are slotted to accommodate joists on 16” or 24” centerlines.
Top and Bottom 1" 1" Access Side 1" 18" Non-Access Side 1" 1" Rear 18" 18" Vent Connector 4" 4"
30 45 60 75 100 12530,000 45,000 60,000 75,000 100,000 125,00024,000 36,000 48,000 60,000 80,000 100,000
505 720 990 1,160 1,490 1,980523 749 653 769 565 747
44 46 45 48 50 47 10 10 12 14 12 16 25 27 36 38 42 56 1/15 1/15 1/12 1/12 1/12 1/8 1,550 1,550 1,625 1,625 1,050 1,550 S.P. S.P. P.S.C. P.S.C. S.P. P.S.C. 2.4 2.4 1.2 1.2 2.7 2.2 3.7 3.7 2.5 2.5 4.7 4.2
* 3" for Model HD, 4" for Model HDS
Model SizeBtu/Hr Input
Btu/Hr OutputEntering Airflow (CFM)
Outlet VelocityAir Temp. Rise (°F)
Mounting Height (Max ft.)Heat Throw (ft.)
Unit Total Amps
3/4* 3/4* 4Vent Connector Size (in.)
Performance
HorsepowerRPMTypeAmps
MotorData
Mounting
ClearancesUnit Side Clearance To
Combustible MaterialsRecommended
Service Clearance
SIZES30-75
SIZES100/125
(ACCESSORY)
.00
1.10
3.10
5.10
7.10
9.10
17.1
0
19.1
0
21.1
0
23.1
0
25.1
026
.20
.00
1.50
3.50
5.50
7.50
9.50
11.5
0
13.5
0
21.5
0
23.5
0
25.5
0
27.5
0
29.5
0
31.5
0
33.5
035
.00
30 45 60 75 100/125 26.8 26.8 26.8 26.8 35.5 12.2 12.2 18.0 18.0 20.5 16.5 16.5 16.5 16.5 22.0 14.9 14.9 14.9 14.9 22.5 10.1 10.1 15.9 15.9 18.4 7.25 7.25 10.75 10.75 14.0 18.5 18.5 18.5 18.5 24.0 7.6 7.6 7.835 7.835 8.4 1/2 1/2 1/2 1/2 1/2 34.5 34.5 34.5 34.5 43.0 22 22 25 25 31.0 2.74 2.74 3.15 3.15 3.87 3.19 3.19 5.55 5.55 10.73
10 10 14 14 18.0 55 60 80 85 125
Model SizeABCDEFGH
Gas ConnectionIJK (HDS only)L (HDS only)
Fan DiameterApprox. Shipping Weight (lbs.)
Dimensions (inches)
Control Options Control Description Control Service Thermostat Type of Model Code No. Voltage Voltage Gas Size
Single-Stage, Direct Spark Ignition, 100% Shut-Off with Continuous Retry 11 115V 24V natural 30-125- Utilizes a single-stage combination gas control with ignition control. Gas is lit with a direct spark igniter on call for heat. 21 115V
24V
propane
30-125
Two-Stage, Direct Spark Ignition, 100% Shut-Off with Continuous Retry 12 115V 24V natural 75-125- Utilizes a two-stage combination gas control with built-in ignition control. Firing rate is 100% and 50% of full rated input. Gas is lit with a direct spark 22 115V 24V propane
75-125igniter on call for heat.
COMBUSTION AIRLOUVERS (HD ONLY)
3 3
3 3
4 4 4Combustion Air Inlet ConnectorSize (Model HDS only) (in.)
B
A
CC (APPROX.)
Clearances for Residentially-Certified Unit Heaters
Unit Side Clearance To Combustible Materials
Recommended Service Clearance
Top and Bottom 1” 1”
Access Side 1” 18”
Non-Access Side 1” 1”/18”1
Rear 18” 18”
Vent Connector 4”/6” 1 4”/6”1
1. For high-efficiency unit only (Model PTC)
CUSTOMIZE YOUR HOT DAWG™ WITH EASY-TO-INSTALL TRIM KITSChoose from three new trim kits. They look great with our standard green units too.
Follow us on Twitter @ModineHVAC
Modine Manufacturing Company1500 DeKoven AvenueRacine, Wisconsin 53403-2552 1.800.828.HEATwww.ModineHVAC.com
EFFINITY™ CONDENSING UNIT HEATER (MODEL PTC)• Up to 97% efficient, all units a minimum
of 93% efficient.
• The most efficient gas-fired, condensing unit heater in North America
• Features Modine’s high-grade stainless steel Conservicore® technology secondary heat exchanger
• All sizes are separated combustion
• A minimum 15% decrease in C02 versus other gas-fired heaters and minimum 17% gas savings (up to 40%)
• A smart investment and respectable ROI with valuable state utility rebates available
1. Ratings shown are for elevations up to 2,000 ft. For elevations above 2,000 feet, ratings should be reduced at the rate of 4% for each 1,000 feet about sea level. (In Canada see rating plate.) Reduction of ratings requires use of high altitude kit.
2. Data taken at 65ºF ambient and unit fired at full-rated input. Mounting height as measured from bottom of unit, and without deflector hoods.
Performance Data - Model PTCModel size 55 65 85 110
Btu/Hr Input1 55,000 65,000 85,000 110,000
Btu/Hr Output1 51,150 60,450 79,050 102,300
Condensate Production (Gal./Hr.) 0.3 0.4 0.5 0.7
Entering Airflow (CFM) @ 70°F2 1,097 1,141 1,650 1,750
Outlet Velocity (FPM)2 618 650 619 668
Air Temp. Rise (°F) 43 49 44 54
Max. Mounting Height (Ft.)2 12 12 13 13
Heat Throw (Ft.) @ Max. Mtg Ht 43 43 48 46
See us on YouTube www.youtube.com/ModineHVAC
DOWNLOAD OUR SAVINGS CALCULATOR APP:
CALCULATE YOUR COST AND ENERGY SAVINGS WITH MODINE’S EFFINITY MOBILE APP
• Ideal for contractors and engineers responsible for specifying HVAC equipment for projects of any size
• By entering simple jobsite data in the intuitive calculator, users can compare products with differing efficiencies, determine the annual cost savings, return on investment and environmental advantages
• The results can be saved, emailed and printed with a simple click
©2015 Modine Manufacturing Co. 6-114.9