Perfect Brake Job. Every time. PFM 9.0 ... - Pro-Cut · PDF filePerfect Brake Job. Every time....
1
10 Technology Drive, #4 West Lebanon, NH 03784 USA 603.298.5200 fax: 603.298.8404 www.procutusa.com Perfect Brake Job. Every time. ETA SWITCH — BROOK CROMPTON .95 hp 800.543.6618 [email protected] SERVICE BULLETIN • 11 PFM 9.2 PFM 9.0 PFM900 VBG620 MODELS: 50-558 Pro-Cut’s new ETA Switch Pro-Cut will be using a new brand and style of on/off switch (50-558). The Manufacturer is ETA, which will replace the current brand. The ETA switch is wired differently but can be used in the VBG620, PFM900, PFM-9.0 and PFM-9.2 lathes. Please use the following Wiring Instructions when installing the ETA switch: Motor: Brook Crompton Motor .95 hp 115 v Computer Box: The Computer and the Motor have an IEC connector. Installation: When installed the letters “ETA” on main switch body (same side as LNE11 and 12k) faces up/out. Terminals: LNE 11 — Thick Light Blue wire from the IEC connector is plugged onto terminal LNE 11. LNE 21 — Thick Tan wire from the IEC connector coupled with the Thick Red wire from the micro switch are plugged onto terminal LNE 21. A-2 — Short Thick Blue wire, connected to a Thick Black wire from the micro switch. The Blue wire is connected to terminal A-2. 12 K — Thick Black wires from the motor crimped together are connected to ter- minal 12 K. 22 I — Thick Light Blue wires from the capacitors, crimped together coupled with a single Thick Black wire from the motor connected to terminal 22 I. Ground — Thick Green wire from the power cord and Thick Striped Green from the micro switch attached to ground, (lower left side of electrical box). Contact the Pro-Cut Service Department with any questions: 800-543-6618.
Transcript of Perfect Brake Job. Every time. PFM 9.0 ... - Pro-Cut · PDF filePerfect Brake Job. Every time....
10 Technology Drive, #4 West Lebanon, NH 03784 USA 603.298.5200 fax: 603.298.8404
www.procutusa.com
Perfect Brake Job. Every time.
ETA SWITCH — BROOK CROMPTON .95 hp
800.543.6618 [email protected]
SERVICE BULLETIN • 11
PFM 9.2PFM 9.0PFM900VBG620
MODELS:
50-558
Pro-Cut’s new ETA Switch
Pro-Cut will be using a new brand and style of on/off switch (50-558). TheManufacturer is ETA, which will replace the current brand. The ETA switch is wireddifferently but can be used in the VBG620, PFM900, PFM-9.0 and PFM-9.2 lathes.Please use the following Wiring Instructions when installing the ETA switch:
Motor: Brook Crompton Motor .95 hp 115 v
Computer Box: The Computer and the Motor have an IEC connector.
Installation: When installed the letters “ETA” on main switch body (same side as LNE11 and12k) faces up/out.
Terminals:LNE 11 — Thick Light Blue wire from the IEC connector is plugged onto terminalLNE 11.
LNE 21 — Thick Tan wire from the IEC connector coupled with the Thick Red wirefrom the micro switch are plugged onto terminal LNE 21.
A-2 — Short Thick Blue wire, connected to a Thick Black wire from the microswitch. The Blue wire is connected to terminal A-2.
12 K — Thick Black wires from the motor crimped together are connected to ter-minal 12 K.
22 I — Thick Light Blue wires from the capacitors, crimped together coupled with asingle Thick Black wire from the motor connected to terminal 22 I.
Ground — Thick Green wire from the power cord and Thick Striped Green fromthe micro switch attached to ground, (lower left side of electrical box).
Contact the Pro-Cut Service Department with any questions: 800-543-6618.
