Per Files
-
Upload
carlos-mejia -
Category
Documents
-
view
59 -
download
0
Transcript of Per Files
Tablas Perfiles
Tabla 1. Especificaciones
Tabla 2. Canal en U o C
Tabla 3. Perfiles UPN
Tabla 4. Perfiles I Estandar Americano - S
Tabla 5. Vigas I Estandar Europeo - IPN
Tabla 6. Vigas I Livianas de Alas Paralelas - IPE
Tabla 7. Vigas HEA
Tabla 8. Vigas HEB
Tabla 9. Vigas H Americanas de Ala ancha- WF
Tabla 10. Perfiles Estructural "C" ACESCO
Tabla 11. Perlines Perfilamos
Tabla 12. Barras Cuadradas
Tabla 13. Perlines Corpacero - Acero Galvanizado y Negro - Perlines sección C - fy 33 Ksi
Tabla 14. Perlines Corpacero - Acero Galvanizado y Negro - Perlines sección C - fy 33 Ksi
Tabla 15. Perlines Corpacero - Acero Galvanizado y Negro - Perlines sección Z - fy 33 Ksi
Tabla 16. Propiedades Geométricas de los Ángulos
Tabla 17. Perfiles en L
Tabla 18. Platinas
PRINCIPAL: Carrera 42 No. 26-18 Itagüí • Teléfono: 277 4699 • Fax: 372 0231 • A.A. 1183 MedellínHIERROS COLOMBIA: Carrera 52 No. 39-59 Medellín • Teléfono: 232 3022 • Fax: 232 5734
BOGOTA: Carrera 128 No. 18-36 Fontibón • Teléfono: 421 1641 • Fax: 421 1080BARRANQUILLA: Vía 40 No. 62-274 • Telefax: 344 0076 - 344 3530
Perfiles
Elementos ASTM A36
- - Tipo 1
Carbono Máx% 0,26 0,23
Manganeso Máx% - 1,35
Fósforo Máx% 0,04 0,04
Azufre Máx% 0,05 0,05
Silicio Máx% 0,04 0,40
Vanadio -
Niobio - 0.005-0.05
Cobre Min% * *
ASTMPunto de Fluencia
mínimoResistencia a la
Tracción
1/2, 3/8, 5/16 20,0
58000 min 1/4 17,5
80000 máx 3/16 15,0
psi 1/8 12,5
1/2, 3/8, 5/16 18,0
1/4 15,5
3/16 13,0
1/8 10,5
A - 572 Grado 50
50000 65000 min
psi psi
* 0.20 cuando se especifique
Propiedades Mecánicas
Alargamiento mínimo% en 200mm
(8 pulgadas)
A - 36
36000
psi
0,40
0.01-0.15
-
*
0,23
1,35
0,04
0,05
Especificaciones
Composición Química
ASTM A572 GRADO 50
Tipo 2
Perfiles
Design. Peso Area
Altura Alma
d bf tf tw Ix Sx rx Iy Sy ry rt d/Af
plgxlb/pie kgf/m cm² cm4 cm3 cm cm4 cm3 cm cm cm-1
C12x20.7 30,6 39,0 305 75 12,70 7,2 5,320 349,0 11,70 156,0 27 2,00 1,72 3,21
C10x15.3 22,6 28,8 254 66 11,10 6,10 2,780 219,0 9,82 91,7 18 1,78 1,56 3,47
C 8x11.5 17,1 21,8 203 57 9,91 5,6 1,350 133,0 7,88 53,1 12 1,56 1,41 3,57
C 6x8.2 12,2 15,5 152 49 8,71 5,1 544 71,4 5,92 27,9 7,7 1,34 1,26 3,59
C 4x5.4 8,00 10,2 102 40 7,52 4,7 159 31,3 3,95 12,8 4,4 1,12 1,13 3,36
C 3X4.1 6,20 7,9 76 36 6,93 4,3 69 18,2 2,96 7,96 3,2 1,00 1,07 3,07
Tabla 2. Canal en U o C
Dimensiones Propiedades Constantes
Cd x Peso P AAlas Eje X-X Eje Y-Y Flexión
mm
Design. Peso Area
Altura Alma
d bf tf tw Ix Sx rx Iy Sy ry rt d/Af
mm x mm kgf/m cm² cm4 cm3 cm cm4 cm3 cm cm cm-1
UPN 100 10,6 13,5 100 50 8,5 6,0 205 41,1 3,91 29,1 8,45 1,47 1,55 2,35
UPN 160 18,9 24,0 160 65 10,5 7,5 925 116,0 6,21 85,0 18,20 1,88 1,84 2,34
UPN 200 25,3 32,2 200 75 11,5 8,5 1,910 191,0 7,71 148,0 26,90 2,14 2,01 2,32
UPN 260 37,9 48,3 260 90 14,0 10,0 4,820 371,0 10,00 317,0 47,80 2,56 2,37 2,06
UPN 300 46,1 58,8 300 100 16,0 10,0 8,030 535,0 11,70 493,0 67,60 2,90 2,70 1,88
Tabla 3. Perfiles UPN
Dimensiones y propiedades para el diseño
Dimensiones Propiedades Constantes
UPNd P AAlas Eje X-X Eje Y-Y Flexión
mm
Perfiles
DesignaciónCons-tors
d tw bf tf Ix Sx rx Iy Sy ry Zx Zy Jt
mm mm mm mm mm cm² kg/mt cm4 cm3 cm cm4 cm3 cm cm3 cm3 cm4
S 4 x 7.7 102,00 4,90 67,64 7,44 64,00 14,60 11,50 253,00 49,80 4,17 31,80 9,40 1,48 57,32 15,80 2,91
S 6 x 12.5 152,00 5,89 84,63 9,12 108,00 23,70 18,60 920,00 120,8 6,22 75,75 17,90 1,79 138,80 30,32 7,08
Tabla 4. Perfiles I Estandar Americano - S
Dimensiones y propiedades para el diseño
Dimensiones Propiedades ElásticasMódulo Plástico
Eje X-X Eje Y-YAreaAltura Peso
hAla
Designación
d tw bf tf Ix Sx rx Iy Sy ry Zx Zy Jt
mm mm mm mm cm² kg/mt cm4 cm3 cm cm4 cm3 cm cm3 cm3 cm4
IPN 100 100,00 4,50 50,00 6,80 10,60 8,34 171,00 34,20 4,01 12,20 4,88 1,07 39,80 8,09 1,60
IPN 160 160,00 6,30 74,00 9,50 22,80 17,90 935,00 117,00 6,40 54,70 14,80 1,55 136,00 24,90 6,57
IPN 200 200,00 7,50 90,00 11,30 33,40 26,20 2140,00 214,00 8,00 117,00 26,00 1,87 250,00 43,50 13,50
IPN 260 260,00 9,40 113,00 14,10 53,30 41,90 5740,00 442,00 10,40 288,00 51,00 2,32 514,00 85,90 33,50
IPN 300 300,00 10,80 125,00 16,20 69,00 54,20 9800,00 653,00 11,90 451,00 72,20 2,56 762,00 121,00 56,80
IPN 360 360,00 13,00 143,00 19,50 97,00 76,10 19610,00 1090,00 14,20 818,00 114,00 2,90 1276,00 194,00 115,00
PESO EJE X-X
Cons-torsALTURA
mm
75
125
159
208
241
290
EJE Y-Y
MODULOPLASTICO
Tabla 5. Vigas I Estandar Europeo - IPN
PERFILES IPN Dimensiones y propiedades para el diseño
AREA
h
DISTANCIAS
DIMENSIONES PROPIEDADES ELASTICAS
ALA
Perfiles
d tw bf tf r c h Ix Sx rx Iy Sy ry Zx Zy Jt
mm mm mm mm mm mm mm cm² kg/mt cm4 cm3 cm cm4 cm3 cm cm3 cm3 cm4
IPE 80 80,00 3,80 46,00 5,20 5,00 69,60 59,60 7,64 6,00 80,10 20,00 3,24 8,50 3,70 1,05 23,20 5,80 0,70
IPE 100 100,00 4,10 55,00 5,70 7,00 88,60 74,60 10,30 8,10 171,00 34,20 4,07 15,90 5,80 1,24 39,40 9,10 1,20
IPE 120 120,00 4,40 64,00 6,30 7,00 107,40 93,40 13,20 10,40 318,00 53,00 4,90 27,70 8,60 1,45 60,70 13,60 1,74
IPE 140 140,00 4,70 73,00 6,90 7,00 126,20 112,20 16,40 12,90 541,00 77,30 5,74 44,90 12,30 1,65 88,30 19,20 2,45
IPE 160 160,00 5,00 82,00 7,40 9,00 145,20 127,20 20,10 15,80 869,00 109,00 6,58 68,30 16,70 1,84 124,00 26,10 3,60
IPE 180 180,00 5,30 91,00 8,00 9,00 164,00 146,00 23,90 18,80 1317,00 146,00 7,42 101,00 22,20 2,05 166,00 34,60 4,79
IPE 200 200,00 5,60 100,00 8,50 12,00 183,00 159,00 28,50 22,40 1943,00 194,00 8,26 142,00 28,50 2,24 221,00 44,60 6,98
IPE 220 220,00 5,90 110,00 9,20 12,00 201,60 177,60 33,40 26,20 2772,00 252,00 9,11 205,00 37,30 2,48 285,00 58,10 9,07
IPE 240 240,00 6,20 120,00 9,80 15,00 220,40 190,40 39,10 30,70 3892,00 324,00 9,97 284,00 47,30 2,69 367,00 73,90 12,90
IPE 270 270,00 6,60 135,00 10,20 15,00 249,60 219,60 45,90 36,10 5790,00 429,00 11,20 420,00 62,20 3,02 484,00 97,00 15,90
IPE 300 300,00 7,10 150,00 10,70 15,00 278,60 248,60 53,80 42,20 8356,00 557,00 12,50 604,00 80,50 3,35 628,00 125,00 20,10
IPE 330 330,00 7,50 160,00 11,50 18,00 307,00 271,00 62,60 49,10 11770,00 713,00 13,70 788,00 98,50 3,55 804,00 154,00 28,10
IPE 360 360,00 8,00 170,00 12,70 18,00 334,60 298,60 72,70 57,10 16270,00 904,00 15,00 1043,00 123,00 3,79 1019,00 191,00 37,30
IPE 400 400,00 8,60 180,00 13,50 21,00 373,00 331,00 84,50 66,30 23130,00 1156,00 16,50 1318,00 146,00 3,95 1307,00 229,00 51,10
IPE 450 450,00 9,40 190,00 14,60 21,00 420,80 378,80 98,80 77,60 33740,00 1500,00 18,50 1676,00 176,00 4,12 1702,00 276,00 66,90
IPE 500 500,00 10,20 200,00 16,00 21,00 468,00 426,00 116,00 90,70 48200,00 1928,00 20,40 2142,00 214,00 4,31 2194,00 336,00 89,30
IPE 550 550,00 11,10 210,00 17,20 24,00 515,60 467,60 134,00 106,00 67120,00 2441,00 22,30 2668,00 254,00 4,45 2787,00 401,00 123,00
IPE 600 600,00 12,00 220,00 19,00 24,00 562,00 514,00 156,00 122,00 92080,00 3069,00 24,30 3387,00 308,00 4,66 3512,00 486,00 165,00
Cons-tors
DesignaciónALA
MODULO PLASTICO
Tabla 6. Vigas I Livianas de Alas Paralelas - IPEPERFILES IPE Dimensiones y propiedades para el diseño
DISTANCIAS EJE X-X EJE Y-YALTURA Area Peso
DIMENSIONES PROPIEDADES ELASTICAS
Perfiles
Design. Peso Area
Altura Alma
d bf tf tw Ix Sx rx Iy Sy ry rt d/Af Zx Zy J
mm x mm kgf/m cm² cm4 cm3 cm cm4 cm3 cm cm cm-1 cm3 cm3 cm4
HEA 100 16,7 21,2 96,00 100,0 8,0 5,0 349,00 72,7 4,05 134 26,7 2,51 2,77 1.200 84 43,6 5,28
120 19,9 25,3 114,00 120,0 8,0 5,0 606,00 106,0 4,89 231 38,4 3,02 3,33 1.190 120 61,9 6,04
140 24,7 31,4 133,00 140,0 8,5 5,5 1,03 155,0 5,73 389 55,6 3,52 3,87 1.120 174 88,5 8,10
160 30,4 38,8 152,00 160,0 9,0 6,0 1,67 220,0 6,57 615 76,9 3,98 4,42 1.060 247 124 12,10
180 35,5 45,3 171,00 180,0 9,5 6,0 2,51 294,0 7,45 924 103,0 4,52 4,98 1.000 326 164 14,90
HEA 200 42,3 53,8 190,00 200,0 10,0 6,5 3,69 389,0 8,28 1330 133,0 4,98 5,53 0,950 432 216 21,00
220 50,50 64,93 210,00 220,0 11,00 7,00 5410 515,00 9,17 1950 178,00 5,51 6,08 0,868 571 284 28,60
240 60,30 76,80 230,00 240,0 12,00 7,50 7760 675,00 10,10 2770 231,00 6,00 6,64 0,799 749 371 42,10
260 68,2 86,8 250,00 260,0 12,5 7,5 10,50 836,0 11,00 3660 282,0 6,5 7,20 0,769 926 458 54,20
HEA 300 88,3 113,0 290,00 300,0 14,0 8,5 18,30 1.260,0 12,70 6310 420,0 7,49 8,30 0,690 1390 682 87,80
340 105,0 133,0 330,00 300,0 16,5 9,5 27,70 1.680,0 14,40 7430 495,0 7,46 8,28 0,667 1960 796 131
360 112,0 143,0 350,00 300,0 17,5 10,0 33,10 1.890,0 15,20 7880 525,0 7,43 8,26 0,667 2100 842 153
HEA 400 125,0 159,0 390,00 300,0 19,0 11,0 45,10 2.310,0 16,80 8560 571,0 7,34 8,21 0,684 2570 913 193
450 140,0 178,0 440,00 300,0 21,0 11,5 63,70 2.900,0 18,90 9460 631,0 7,29 8,18 0,698 3230 1010 250
500 155,0 198,0 490,00 300,0 23,0 12,0 87,00 3.550,0 21,00 10400 691,0 7,24 8,15 0,710 3960 1100 318
550 166,0 212,0 540,00 300,0 24,0 12,5 112,00 4.150,0 23,00 10800 721,0 7,15 8,10 0,750 4630 1150 360
HEA 600 178,0 226,0 590,00 300,0 25,0 13,0 141,00 4.790,0 25,00 11300 751,0 7,05 8,06 0,787 5360 1190 407
Tabla 7. Vigas HEADimensiones y propiedades para el diseño
MODULO PLASTICOConstante
torsiónDimensiones Propiedades Constantes
HEAd P AAlas Eje X-X Eje Y-Y Flexión
mm
Perfiles
ALTURA ALMA
HEBd P A d bf tf tw Ix Sx rx Iy Sy ry rt d/Af J Zx Zy
mm x mm kgf/m cm² cm4 cm3 cm cm4 cm3 cm cm cm-1 cm4 cm3 cm3
160 42,60 54,30 160,00 160,00 13,00 8,00 2490,00 311,00 6,78 889,00 111,00 4,05 4,43 0,769 31,3 356 176
260 93,00 118,00 260,00 260,00 17,50 10,00 14900,00 1150,00 11,20 5130,00 395,00 6,58 7,21 0,571 127 1290 629
300 117,00 149,00 300,00 300,00 19,00 11,00 25200,00 1680,00 13,00 8560,00 571,00 7,58 8,32 0,526 189 1880 910
MODULO PLASTICO
Tabla 8. Vigas HEB
Constantetorsión
PERFILES HEB Dimensiones y propiedades para el diseño
FLEXIONEJE X-XALAS
mm
PROPIEDADES ConstantesDIMENSIONESDesignación PESO AREA
EJE Y-Y
EJE X-X EJE Y-Y
d tw bf tf r c d Ix Sx rx Iy Sy ry Zx Zy Jt
mm mm mm mm mm mm mm cm² kg/mt cm4 cm3 cm cm4 cm3 cm cm3 cm3 cm4
WF4x13 102,00 6,5 100 9,4 6 83,2 71,2 24,5 19,35 441 86,40 4,2 157 31,40 2,53 99,50 48,0 6,90
WF6x15 152,00 5,8 152 6,6 6 138,8 126,8 28,4 22,32 1.205 159,00 6,5 387 50,90 3,69 176,00 77,5 4,31
WF6x20 157,00 6,6 153 9,3 6 138,4 126,4 37,9 29,76 1.714 218,00 6,7 556 72,60 3,83 244,00 111,0 10,20
WF8x31 203,00 7,2 203 11,0 10 181,0 161,0 58,6 46,13 4.543 448,00 8,8 1.535 151,00 5,12 495,00 229,0 22,20
WF8x40 210,00 9,1 205 14,2 10 181,6 161,6 75,6 59,53 6.111 582,00 9,0 2.040 199,00 5,20 653,00 303,0 46,80
WF10x22 258,00 6,1 146 9,1 8 239,8 223,8 41,7 32,74 4.895 379,00 10,8 473 64,70 3,36 425,00 99,5 10,00
WF10x49 253,00 8,6 254 14,2 13 224,6 195,6 92,9 72,92 11.280 892,00 11,0 3.880 306,00 6,46 986,00 463,0 57,80
WF10x60 260,00 10,7 256 17,3 13 225,4 199,4 114,0 89,29 14.260 1.097,00 11,2 4.841 378,00 6,51 1.227,00 575,0 105,00
WF12x26 310,00 5,8 165 9,7 8 290,6 274,6 49,4 38,69 8.518 550,00 13,1 727 88,10 3,84 611,00 135,0 12,70
WF12x65 308,00 9,9 305 15,4 15 277,2 247,2 123,0 96,72 22.240 1.444,00 13,4 7.286 478,00 7,69 1.591,00 725,0 91,50
WF14x30 352,00 6,9 171 9,8 10 332,4 312,4 57,3 44,65 12.160 691,00 14,6 818 95,70 3,78 778,00 148,0 16,20
WF14x61 353,00 9,5 254 16,4 15 320,2 290,2 116,0 90,78 26.690 1.512,00 15,2 4.483 353,00 6,23 1.676,00 538,0 91,20
WF14x90 356,00 11,2 369 18,0 15 320,0 290,0 171,0 133,93 41.510 2.332,00 15,6 15.080 817,00 9,40 2.562,00 1.237,0 169,00
WF16x36 403,00 7,5 177 10,9 10 381,2 361,2 68,0 53,57 18.600 923,00 16,5 1.009 114,00 3,85 1.045,00 177,0 22,80
Designación
PROPIEDADES ELASTICAS
ALTURA ALA DISTANCIAS
DIMENSIONES
Peso
Tabla 9. Vigas H Americanas de Ala ancha- WF
PERFILES WF Dimensiones y propiedades para el diseño
Area
Cons-tors
MODULO PLASTICO
Perfiles
Espesor Calibre A B C Peso Area X m t Vena Warping j
mm # mm mm mm kg/ml mm² mm mm J mm4 Cw mm6 mm Ix mm4 Iy mm4 Sx mm3 Sy mm3 rx mm ry mm ro mm
PHR-C60x40-3.0 mm 3,0 11 60,0 40,0 14,0 3,58 429,3 14,4 23,6 1.287,9 91510858,2 47,3 230729 87294 7691,0 3616,6 23,2 14,3 46,7
PHR-C60x40-2.5 mm 2,5 12 60,0 40,0 14,0 2,98 363,8 14,6 23,8 758,0 81693980,6 47,6 199584 76484 6652,8 3170,6 23,4 14,5 47,3
PHR/PAG-C60x40-1.9 mm 1,9 14 60,0 40,0 14,0 2,27 282,0 14,9 24,1 339,4 67351338,7 48,0 158508 61650 5283,6 2557,4 23,7 14,8 48,0
PHR/PAG-C60x40-1.5 mm 1,5 16 60,0 40,0 14,0 1,79 225,6 15,2 24,2 169,2 56095662,7 48,3 128805 50580 4293,5 2099,1 23,9 15,0 48,4
PHR/PAG-C60x40-1.2 mm 1,2 18 60,0 40,0 14,0 1,43 182,2 15,3 24,4 87,5 46697212,7 48,5 105276 41632 3509,2 1728,3 24,0 15,1 48,8
PHR/PAG-C60x40-0.9 mm 0,9 20 60,0 40,0 14,0 1,07 138,0 15,5 24,5 37,3 36432345,7 48,7 80652 32115 2688,4 1333,7 24,2 15,3 49,1
PHR-C120x60-3.0 mm 3,0 11 120,0 60,0 13,0 5,72 723,3 17,4 28,7 2.169,9 926540065,5 77,8 1625934 310414 27098,9 7550,5 47,4 20,7 69,3
PHR-C120x60-2.5 mm 2,5 12 120,0 60,0 13,0 4,77 608,8 17,7 28,9 1.268,4 806032752,3 77,9 1383565 267792 23059,4 6516,1 47,7 21,0 69,9
PHR/PAG-C120x60-1.9 mm 1,9 14 120,0 60,0 13,0 3,62 468,2 18,0 29,2 563,5 644683606,5 78,0 1077920 212011 17965,3 5160,9 48,0 21,3 70,6
PHR/PAG-C120x60-1.5 mm 1,5 16 120,0 60,0 13,0 2,86 372,6 18,2 29,4 279,4 526457667,4 78,1 865039 171931 14417,3 4186,4 48,2 21,5 71,1
PHR/PAG-C120x60-1.2 mm 1,2 18 120,0 60,0 13,0 2,29 299,8 18,3 29,6 143,9 431868197,8 78,2 700523 140313 11675,4 3417,2 48,3 21,6 71,4
PHR/PAG-C120x60-0.9 mm 0,9 20 120,0 60,0 13,0 1,72 226,2 18,5 29,7 61,1 332106440,2 78,3 531802 107335 8863,4 2614,5 48,5 21,8 71,8
PHR-C160x60-3.0 mm 3,0 11 160,0 60,0 20,0 7,16 885,3 16,9 29,2 2.655,9 2316887707,6 92,4 3365234,999 412396 42065,4 9915,9 61,7 21,6 80,0
PHR-C160x60-2.5 mm 2,5 12 160,0 60,0 20,0 5,97 743,8 17,2 29,5 1.549,6 2003598470,6 92,3 2852311 354341,9999 35653,9 8518,8 61,9 21,8 80,5
PHR/PAG-C160x60-1.9 mm 1,9 14 160,0 60,0 20,0 4,53 570,8 17,4 29,8 686,9 1591308516,3 92,3 2211889 279233,9999 27648,6 6711,9 62,2 22,1 81,2
PHR/PAG-C160x60-1.5 mm 1,5 16 160,0 60,0 20,0 3,58 453,6 17,6 30,0 340,2 1293426777,9 92,3 1769649 225770 22120,6 5426,2 62,5 22,3 81,6
PHR/PAG-C160x60-1.2 mm 1,2 18 160,0 60,0 20,0 2,86 364,6 17,8 30,1 175,0 1057464219,3 92,3 1429853 183849 17873,2 4418,3 62,6 22,5 82,0
PHR-C220X80-3.0 mm 3,0 11 220,0 80,0 20,0 9,54 1.185,3 21,0 35,8 3.555,9 9161075531,3 127,3 8625872 932157 78417,0 16200,2 85,3 28,0 106,2
PHR-C220X80-2.5 mm 2,5 12 220,0 80,0 20,0 7,95 993,8 21,2 36,1 2.070,5 7851745845,7 127,1 7279716 795628 66179,2 13826,0 85,6 28,3 106,8
PHR/PAG-C220X80-1.9 mm 1,9 14 220,0 80,0 20,0 6,04 760,8 21,5 36,4 915,6 6170466927,9 126,9 5616578 622110 51059,8 10809,4 85,9 28,6 107,5
PHR/PAG-C220X80-1.5 mm 1,5 16 220,0 80,0 20,0 4,77 603,6 21,7 36,6 452,7 4980653728,5 126,8 4478614,999 500439 40714,7 8694,6 86,1 28,8 107,9
PHR/PAG-C220X80-1.2 mm 1,2 18 220,0 80,0 20,0 3,82 484,6 21,8 36,7 232,6 4051048902,7 126,8 3609687,999 405984,9999 32815,3 7053,1 86,3 28,9 108,3
PHR-C305X80-3.0 mm 3,0 11 305,0 80,0 25,0 11,78 1.470,3 18,5 33,8 4.410,9 21543425443,9 178,1 19268714 1129271 126352,2 18811,3 114,5 27,7 128,9
PHR-C305X80-2.5 mm 2,5 12 305,0 80,0 25,0 9,81 1.231,3 18,7 34,0 2.565,3 18405884197,5 177,5 16223589 962605 106384,2 16026,8 114,8 28,0 129,4
PHR/PAG-C305X80-1.9 mm 1,9 14 305,0 80,0 25,0 7,46 941,3 19,0 34,3 1.132,8 14410235705,8 176,7 12482372 751517 81851,6 12504,7 115,2 28,3 130,0
PHR-C355X110-3.0 mm 3,0 11 355,0 110,0 25,0 14,32 1.800,3 26,3 45,8 5.400,9 64298487034,5 203,1 33392925,99 2591692,999 188129,2 31532,4 136,2 37,9 158,7
PHR-C355X110-2.5 mm 2,5 12 355,0 110,0 25,0 11,93 1.506,3 26,5 46,0 3.138,2 54636274290,6 202,7 28061252 2197511 158091,6 26731,0 136,5 38,2 159,2
PHR/PAG-C355X110-1.9 mm 1,9 14 355,0 110,0 25,0 9,07 1.150,3 26,8 46,3 1.384,3 42500697474,8 202,3 21540680 1704926 121355,9 20734,1 136,8 38,5 159,9
Tabla 10. Perfiles Estructural "C" ACESCO
Propiedades Mecánicas de la sección completa
Referencia Perfil
Momento de Inercia Modulo de Sección Radio de Giro
Perfiles
e A B C Peso AreaCentroide
dm
St VenaJ
WarpingCw
j
mm cm cm cm kg/m cm² cm cm J cm4 Cw cm6 cm Ix cm4 Iy cm4 Sx cm3 Sy cm3 rx cm ry cm ro cm
3" x 2" 2 7,62 5,08 1,91 3,08 3,92 1,97 3,06 0,0522 268,92 6,02 36,01 14,55 9,45 4,67 3,03 1,93 6,18
4" x 2" 2 10,16 5,08 1,91 3,48 4,42 1,74 2,85 0,0590 441,14 6,56 70,78 16,29 13,93 4,88 4,00 1,92 6,38
5" x 2" 2 12,70 5,08 1,91 3,88 4,93 1,56 2,67 0,0658 676,71 7,46 119,83 17,67 18,87 5,02 4,93 1,89 6,77
6" x 2" 2 15,24 5,08 1,91 4,28 5,44 1,41 2,52 0,0725 981,51 8,69 184,79 18,79 24,25 5,13 5,83 1,86 7,27
6" x 2-5/8" 2 15,24 6,67 1,91 4,78 6,07 2,02 3,32 0,0810 1856,80 9,21 220,70 36,32 28,96 7,81 6,03 2,45 8,41
7" x 2-5/8" 2 17,78 6,67 1,91 5,18 6,58 1,86 3,17 0,08780 2569,85 10,33 316,37 38,22 35,59 7,95 6,94 2,41 8,90
8" x 2-5/8" 2 20,32 6,67 1,91 5,58 7,09 1,73 3,03 0,0945 3430,90 11,70 433,28 39,86 42,65 8,07 7,82 2,37 9,45
8" x 3" 2,5 20,32 7,62 1,91 7,30 9,28 2,05 3,47 0,1933 5706,58 11,83 581,91 67,43 57,27 12,10 7,92 2,70 10,20
Tabla 11. Perlines Perfilamos
Propiedades Físicas
Referencia
Momento Inercia
Módulo de Sección
Radio de Giro
Medidas B=B
9 mm
10 mm
11 mm
12 mm
1/2"
5/8"
3/4"
1"
Kg./ m
0,64
0,79
2,52
3,63
0,95
1,13
1,27
1,98
6,45
Tabla 12. Barras Cuadradas
2,85
5,07
Area
0,81
1,00
1,21
1,44
1,61
Perfiles
Referencia CalibreEspesor
e(mm)A (mm) B (mm) c (mm)
Area
(cm2)
Peso
(Kg/ml)Ix (cm4) Sx (cm3) Rx (cm) Iy (cm4) Sy (cm3) Ry (cm)
P-14-11-N 11 3,00 355,60 63,50 19,10 15,21 11,73 2.852,65 160,44 12,83 70,64 13,97 2,02
P-14-11-G 11 3,00 355,60 63,50 19,10 15,21 11,82 2.852,65 160,44 12,83 70,64 13,97 2,02
P-14-12-N 12 2,50 355,60 63,50 19,10 13,52 9,77 2.239,87 125,98 12,87 56,87 11,22 2,05
P-14-12-G 12 2,50 355,60 63,50 19,10 13,52 9,87 2.239,87 125,98 12,87 56,87 11,22 2,05
P-14-14-N 14 2,00 355,60 63,50 19,10 10,25 7,82 1.709,39 96,14 12,91 44,14 8,69 2,07
P-14-14-G 14 2,00 355,60 63,50 19,10 10,25 7,92 1.709,39 96,14 12,91 44,14 8,69 2,07
P-12-11-N 11 3,00 304,80 63,50 19,10 14,60 10,52 1.842,92 120,93 11,23 65,87 13,33 2,12
P-12-11-G 11 3,00 304,80 63,50 19,10 14,60 10,64 1.842,92 120,93 11,23 65,87 13,33 2,12
P-12-12-N 12 2,50 304,80 63,50 19,10 12,17 8,77 1.535,77 100,77 11,23 54,89 11,11 2,12
P-12-12-G 12 2,50 304,80 63,50 19,10 12,17 8,87 1.535,77 100,77 11,23 54,89 11,11 2,12
P-12-14-N 14 2,00 304,80 63,50 19,10 9,24 7,02 1.173,28 76,99 11,27 42,63 8,61 2,15
P-12-14-G 14 2,00 304,80 63,50 19,10 9,24 7,11 1.173,28 76,99 11,27 42,63 8,61 2,15
P-12-16-N 16 1,50 304,80 63,50 19,10 6,96 5,26 888,21 58,28 11,30 32,79 6,61 2,17
P-12-16-G 16 1,50 304,80 63,50 19,10 6,96 5,36 888,21 58,28 11,30 32,79 6,61 2,17
P-12-18-N 18 1,20 304,80 63,50 19,10 5,58 4,21 714,54 46,89 11,31 26,65 5,37 2,19
P-12-18-G 18 1,20 304,80 63,50 19,10 5,58 4,30 714,54 46,89 11,31 26,65 5,37 2,19
P-10-11-N 11 3,00 254,00 63,50 19,10 13,00 9,34 1.186,48 93,42 9,55 62,89 13,15 2,20
P-10-11-G 11 3,00 254,00 63,50 19,10 13,00 9,43 1.186,48 93,42 9,55 62,89 13,15 2,20
P-10-12-N 12 2,50 254,00 63,50 19,10 10,83 7,78 988,73 77,85 9,56 52,41 10,96 2,20
P-10-12-G 12 2,50 254,00 63,50 19,10 10,83 7,86 988,73 77,85 9,56 52,41 10,96 2,20
P-10-14-N 14 2,00 254,00 63,50 19,10 8,22 6,22 756,36 59,56 9,59 40,74 8,50 2,23
P-10-14-G 14 2,00 254,00 63,50 19,10 8,22 6,31 756,36 59,56 9,59 40,74 8,50 2,23
P-10-16-N 16 1,50 254,00 63,50 19,10 6,20 4,67 573,18 45,13 9,62 31,33 6,53 2,25
P-10-16-G 16 1,50 254,00 63,50 19,10 6,20 4,75 573,18 45,13 9,62 31,33 6,53 2,25
P-10-18-N 18 1,20 254,00 63,50 19,10 4,97 3,73 461,39 36,33 9,63 25,46 5,30 2,26
P-10-18-G 18 1,20 254,00 63,50 19,10 4,97 3,88 461,39 36,33 9,63 25,46 5,30 2,26
P-8-11-N 11 3,00 203,20 63,50 19,10 11,38 8,14 697,63 68,66 7,83 59,09 12,90 2,28
P-8-11-G 11 3,00 203,20 63,50 19,10 11,38 8,22 697,63 68,66 7,83 59,09 12,90 2,28
P-8-12-N 12 2,50 203,20 63,50 19,10 9,48 6,78 581,36 57,22 7,83 49,24 10,75 2,28
P-8-12-G 12 2,50 203,20 63,50 19,10 9,48 6,85 581,36 57,22 7,83 49,24 10,75 2,28
P-8-14-N 14 2,00 203,20 63,50 19,10 7,21 5,42 445,54 43,85 7,86 38,30 8,35 2,31
P-8-14-G 14 2,00 203,20 63,50 19,10 7,21 5,50 445,54 43,85 7,86 38,30 8,35 2,31
P-8-16-N 16 1,50 203,20 63,50 19,10 5,43 4,07 338,10 33,28 7,89 29,44 6,42 2,33
P-8-16-G 16 1,50 203,20 63,50 19,10 5,43 4,14 338,10 33,28 7,89 29,44 6,42 2,33
P-8-18-N 18 1,20 203,20 63,50 19,10 4,36 3,25 272,39 26,81 7,90 23,91 5,21 2,34
P-8-18-G 18 1,20 203,20 63,50 19,10 4,36 3,33 272,39 26,81 7,90 23,91 5,21 2,34
P-6-11-N 11 3,00 152,40 63,50 19,10 9,76 7,66 355,57 46,66 6,04 54,02 12,54 2,35
P-6-11-G 11 3,00 152,40 63,50 19,10 9,76 7,74 355,57 46,66 6,04 54,02 12,54 2,35
P-6-12-N 12 2,50 152,40 63,50 19,10 8,13 6,38 296,31 38,89 6,04 45,02 10,45 2,35
P-6-12-G 12 2,50 152,40 63,50 19,10 8,13 6,46 296,31 38,89 6,04 45,02 10,45 2,35
P-6-14-N 14 2,00 152,40 63,50 19,10 6,19 4,86 227,70 29,88 6,07 35,05 8,13 2,38
P-6-14-G 14 2,00 152,40 63,50 19,10 6,19 4,94 227,70 29,88 6,07 35,05 8,13 2,38
P-6-16-N 16 1,50 152,40 63,50 19,10 4,67 3,67 173,15 22,72 6,09 26,94 6,25 2,40
P-6-16-G 16 1,50 152,40 63,50 19,10 4,67 3,75 173,15 22,72 6,09 26,94 6,25 2,40
P-6-18-N 18 1,20 152,40 63,50 19,10 3,75 2,94 139,67 18,33 6,10 21,87 5,07 2,41
P-6-18-G 18 1,20 152,40 63,50 19,10 3,75 3,02 139,67 18,33 6,10 21,87 5,07 2,41
Nota: Los valores de inercia y módulos de sección no tienen en cuenta la posible reducción por concepto de la relación (w/t) aplicable a perfiles de lámina delgada.
Tabla 13. Perlines Corpacero - Acero Galvanizado y Negro - Perlines sección C - fy 33 Ksi
DIMENSIONES EJES PRINCIPALES
Perfiles
Referencia CalibreEspesor
e(mm)A (mm) B (mm) c (mm)
Area
(cm2)
Peso
(Kg/ml)Ix (cm4) Sx (cm3) Rx (cm) Iy (cm4) Sy (cm3) Ry (cm)
P-150-12-N 12 2,5 150 50 20 6,79 5,33 223,38 29,78 5,74 22,99 16,27 1,84
P-150-12-G 12 2,5 150 50 20 6,79 5,38 223,38 29,78 5,74 22,99 16,27 1,84
P-150-14-N 14 2 150 50 20 5,46 4,28 180,74 24,10 5,76 18,87 13,17 1,86
P-150-14-G 14 2 150 50 20 5,46 4,33 180,74 24,10 5,76 18,87 13,17 1,86
P-150-16-N 16 1,5 150 50 20 4,12 3,23 137,31 18,31 5,78 14,55 10,01 1,88
P-150-16-G 16 1,5 150 50 20 4,12 3,28 137,31 18,31 5,78 14,55 10,01 1,88
P-150-18-N 18 1,2 150 50 20 3,30 2,59 110,70 14,76 5,79 11,83 8,07 1,89
P-150-18-G 18 1,2 150 50 20 3,30 2,64 110,70 14,76 5,79 11,83 8,07 1,89
P-150-20-N 20 0,9 150 50 20 2,54 2,00 86,92 11,59 5,85 9,44 6,30 1,93
P-150-20-G 20 0,9 150 50 20 2,54 2,05 86,92 11,59 5,85 9,44 6,30 1,93
P-125-12-N 12 2,5 125 50 20 6,16 4,84 144,73 23,16 4,85 21,61 13,89 1,87
P-125-12-G 12 2,5 125 50 20 6,16 4,88 144,73 23,16 4,85 21,61 13,89 1,87
P-125-14-N 14 2 125 50 20 4,96 3,89 117,28 18,76 4,86 17,74 11,25 1,89
P-125-14-G 14 2 125 50 20 4,96 3,94 117,28 18,76 4,86 17,74 11,25 1,89
P-125-16-N 16 1,5 125 50 20 3,74 2,94 89,24 14,28 4,88 13,67 8,56 1,91
P-125-16-G 16 1,5 125 50 20 3,74 2,98 89,24 14,28 4,88 13,67 8,56 1,91
P-125-18-N 18 1,2 125 50 20 3,00 2,36 72,01 11,52 4,90 11,12 6,90 1,92
P-125-18-G 18 1,2 125 50 20 3,00 2,40 72,01 11,52 4,90 11,12 6,90 1,92
p-125-20-N 20 0,9 125 50 20 2,32 1,82 56,74 9,08 4,95 8,89 5,41 1,96
P-125-20-G 20 0,9 125 50 20 2,32 1,87 56,74 9,08 4,95 8,89 5,41 1,96
P-100-14-N 14 2 100 50 20 4,46 3,50 69,31 13,86 3,94 16,36 9,33 1,92
P-100-14-G 14 2 100 50 20 4,46 3,54 69,31 13,86 3,94 16,36 9,33 1,92
P-100-16-N 16 1,5 100 50 20 3,37 2,64 52,86 10,57 3,96 12,61 7,10 1,94
P-100-16-G 16 1,5 100 50 20 3,37 2,68 52,86 10,57 3,96 12,61 7,10 1,94
P-100-18-N 18 1,2 100 50 20 2,70 2,12 42,71 8,54 3,97 10,25 5,73 1,95
P-100-18-G 18 1,2 100 50 20 2,70 2,16 42,71 8,54 3,97 10,25 5,73 1,95
P-100-20-N 20 0,9 100 50 20 2,09 1,64 33,82 6,76 4,02 8,22 4,51 1,98
P-100-20-G 20 0,9 100 50 20 2,09 1,69 33,82 6,76 4,02 8,22 4,51 1,98
P-100-22-N 22 0,75 100 50 20 1,75 1,38 28,47 5,69 4,03 6,94 3,79 1,99
P-100-22-G 22 0,75 100 50 20 1,75 1,42 28,47 5,69 4,03 6,94 3,79 1,99
P-75-16-N 16 1,5 75 45 15 2,69 2,11 24,37 6,50 3,01 7,76 4,76 1,70
P-75-16-G 16 1,5 75 45 15 2,69 2,14 24,37 6,50 3,01 7,76 4,76 1,70
P-75-18-N 18 1,2 75 45 15 2,16 1,70 19,75 5,27 3,02 6,32 3,85 1,71
P-75-18-G 18 1,2 75 45 15 2,16 1,73 19,75 5,27 3,02 6,32 3,85 1,71
P-75-20-N 20 0,9 75 45 15 1,69 1,32 15,83 4,22 3,06 5,15 3,08 1,75
P-75-20-G 20 0,9 75 45 15 1,69 1,36 15,83 4,22 3,06 5,15 3,08 1,75
P-75-22-N 22 0,75 75 45 15 1,42 1,11 13,36 3,56 3,07 4,37 2,59 1,76
P-75-22-G 22 0,75 75 45 15 1,42 1,15 13,36 3,56 3,07 4,37 2,59 1,76
P-60-16-N 16 1,5 60 30 10 1,87 1,46 10,21 3,40 2,34 2,20 2,28 1,09
P-60-16-G 16 1,5 60 30 10 1,87 1,49 10,21 3,40 2,34 2,20 2,28 1,09
P-60-18-N 18 1,2 60 30 10 1,50 1,18 8,31 2,77 2,35 1,81 1,85 1,10
P-60-18-G 18 1,2 60 30 10 1,50 1,20 8,31 2,77 2,35 1,81 1,85 1,10
P-60-20-N 20 0,9 60 30 10 1,19 0,94 6,88 2,29 2,40 1,55 1,53 1,14
P-60-20-G 20 0,9 60 30 10 1,19 0,96 6,88 2,29 2,40 1,55 1,53 1,14
P-60-22-N 22 0,75 60 30 10 1,00 0,79 5,83 1,94 2,41 1,33 1,29 1,15
P-60-22-G 22 0,75 60 30 10 1,00 0,81 5,83 1,94 2,41 1,33 1,29 1,15
Nota: Los valores de inercia y módulos de sección no tienen en cuenta la posible reducción por concepto de la relación (w/t) aplicable a perfiles de lámina delgada.
Tabla 14. Perlines Corpacero - Acero Galvanizado y Negro - Perlines sección C - fy 33 Ksi
DIMENSIONES EJES PRINCIPALES
Perfiles
Referencia CalibreEspesor
e(mm)A (mm) B (mm) c (mm)
Area
(cm2)
Peso
(Kg/ml)Ix (cm4) Sx (cm3) Rx (cm) Iy (cm4) Sy (cm3) Ry (cm)
Z-14-11-N 11 3,00 355,60 63,50 19,10 15,21 11,73 2.852,65 160,44 12,83 65,45 10,31 2,07
Z-14-11-G 11 3,00 355,60 63,50 19,10 15,21 11,82 2.852,65 160,44 12,83 65,45 10,31 2,07
Z-14-12-N 12 2,50 355,60 63,50 19,10 13,52 9,77 2.239,87 125,98 12,87 59,56 9,38 2,10
Z-14-12 G 12 2,50 355,60 63,50 19,10 13,52 9,87 2.239,87 125,98 12,87 59,56 9,38 2,10
Z-14-14-N 14 2,00 355,60 63,50 19,10 10,25 7,82 1.709,39 96,14 12,91 51,89 8,17 2,25
Z-14-14-G 14 2,00 355,60 63,50 19,10 10,25 7,92 1.709,39 96,14 12,91 51,89 8,17 2,25
Z-12-11-N 11 3,00 304,80 63,50 19,10 14,60 10,52 1.842,92 120,93 11,23 65,45 10,31 2,12
Z-12-11-G 11 3,00 304,80 63,50 19,10 14,60 10,64 1.842,92 120,93 11,23 65,45 10,31 2,12
Z-12-12-N 12 2,50 304,80 63,50 19,10 12,17 8,77 1.535,77 100,77 11,23 59,56 9,38 2,21
Z-12-12-G 12 2,50 304,80 63,50 19,10 12,17 8,87 1.535,77 100,77 11,23 59,56 9,38 2,21
Z-12-14-N 14 2,00 304,80 63,50 19,10 9,24 7,02 1.173,28 76,99 11,27 51,89 8,17 2,37
Z-12-14-G 14 2,00 304,80 63,50 19,10 9,24 7,11 1.173,28 76,99 11,27 51,89 8,17 2,37
Z-12-16-N 16 1,50 304,80 63,50 19,10 6,96 5,26 888,21 58,28 11,30 42,28 6,66 2,46
Z-12-16-G 16 1,50 304,80 63,50 19,10 6,96 5,36 888,21 58,28 11,30 42,28 6,66 2,46
Z-12-18-N 18 1,20 304,80 63,50 19,10 5,58 4,21 714,54 46,89 11,31 35,51 5,59 2,52
Z-12-18-G 18 1,20 304,80 63,50 19,10 5,58 4,30 714,54 46,89 11,31 35,51 5,59 2,52
Z-10-11-N 11 3,00 254,00 63,50 19,10 13,00 9,34 1.186,48 93,42 9,55 65,45 10,31 2,24
Z-10-11-G 11 3,00 254,00 63,50 19,10 13,00 9,43 1.186,48 93,42 9,55 65,45 10,31 2,24
Z-10-12-N 12 2,50 254,00 63,50 19,10 10,83 7,78 988,73 77,85 9,56 59,56 9,38 2,35
Z-10-12-G 12 2,50 254,00 63,50 19,10 10,83 7,86 988,73 77,85 9,56 59,56 9,38 2,35
Z-10-14-N 14 2,00 254,00 63,50 19,10 8,22 6,22 756,36 59,56 9,59 51,89 8,17 2,51
Z-10-14-G 14 2,00 254,00 63,50 19,10 8,22 6,31 756,36 59,56 9,59 51,89 8,17 2,51
Z-10-16-N 16 1,50 254,00 63,50 19,10 6,20 4,67 573,18 45,13 9,62 42,28 6,66 2,61
Z-10-16-G 16 1,50 254,00 63,50 19,10 6,20 4,75 573,18 45,13 9,62 42,28 6,66 2,61
Z-10-18-N 18 1,20 254,00 63,50 19,10 4,97 3,73 461,39 36,33 9,63 35,51 5,59 2,67
Z-10-18-G 18 1,20 254,00 63 50 19,10 4,97 3,88 461,39 36,33 9,63 35,51 5,59 2,67
Z-8-11-N 11 3,00 203,20 63,50 19,10 11,38 8,14 697,63 68,66 7,83 65,45 10,31 2,40
Z-8-11-G 11 3,00 203,20 63,50 19,10 11,38 8,22 697,63 68,66 7,83 65,45 10,31 2,40
Z-8-12-N 12 2,50 203,20 63,50 19,10 9,48 6,78 581,36 57,22 7,83 59,56 9,38 2,51
Z-8-12-G 12 2,50 203,20 63,50 19,10 9,48 6,85 581,36 57,22 7,83 59,56 9,38 2,51
Z-8-14-N 14 2,00 203,20 63,50 19,10 7,21 5,42 445,54 43,85 7,86 51,89 8,17 2,68
Z-8-14-G 14 2,00 203,20 63,50 19,10 7,21 5,50 445,54 43,85 7,86 51,89 8,17 2,68
Z-8-16-N 16 1,50 203,20 63,50 19,10 5,43 4,07 338,10 33,28 7,89 42,28 6,66 2,79
Z-8-16-G 16 1,50 203,20 63,50 19,10 5,43 4,14 338,10 33,28 7,89 42,28 6,66 2,79
Z-8-18-N 18 1,20 203,20 63,50 19,10 4,36 3,25 272,39 26,81 7,90 35,51 5,59 2,85
Z-8-18-G 18 1,20 203,20 63,50 19,10 4,36 3,33 272,39 26,81 7,90 35,51 5,59 2,85
Z-6-11-N 11 3,00 152,40 63,50 19,10 9,76 7,66 355,57 46,66 6,04 65,45 10,31 2,59
Z-6-11-G 11 3,00 152,40 63,50 19,10 9,76 7,74 355,57 46,66 6,04 65,45 10,31 2,59
Z-6-12-N 12 2,50 152,40 63,50 19,10 8,13 6,38 296,31 38,89 6,04 59,56 9,38 2,71
Z-6-12-G 12 2,50 152,40 63,50 19,10 8,13 6,46 296,31 38,89 6,04 59,56 9,38 2,71
Z-6-14-N 14 2,00 152,40 63,50 19,10 6,19 4,86 227,70 29,88 6,07 51,89 8,17 2,90
Z-6-14-G 14 2,00 152,40 63,50 19,10 6,19 4,94 227,70 29,88 6,07 51,89 8,17 2,90
Z-6-16-N 16 1,50 152,40 63,50 19,10 4,67 3,67 173,15 22,72 6,09 42,28 6,66 3,01
Z-6-16-G 16 1,50 152,40 63,50 19,10 4,67 3,75 173,15 22,72 6,09 42,28 6,66 3,01
Z-6-18-N 18 1,20 152,40 63,50 19,10 3,75 2,94 139,67 18,33 6,10 35,51 5,59 3,08
Z-6-18-G 18 1,20 152,40 63,50 19,10 3,75 3,02 139,67 18,33 6,10 35,51 5,59 3,08
Tabla 15. Perlines Corpacero - Acero Galvanizado y Negro - Perlines sección Z - fy 33 Ksi
DIMENSIONES EJES PRINCIPALES
Perfiles
Eje ZZ
pulg mm pulg mm lb/ft kg/ml pul² cm² I cm4 S cm3 r cm x1 - y1 cm r cm
4x4 101.6 x 101.6 1/4 6,35 6,60 9,82 1,94 12,50 124,86 18,03 3,17 2,77 2,03
4x4 101.6 x 101.6 5/16 7,94 8,20 12,20 2,40 15,50 153,99 21,30 3,15 2,84 2,00
4x4 101.6 x 101.6 3/8 9,53 9,80 14,58 2,86 18,50 184,79 24,58 3,12 2,89 2,00
4x4 101.6 x 101.6 1/2 12,7 12,80 19,50 3,75 24,40 233,07 32,78 3,10 3,00 1,98
3x3 76.2 x 76.2 1/4 6,35 4,90 7,29 1,44 9,30 49,94 9,51 2,36 2,13 1,49
3x3 76.2 x 76.2 5/16 7,94 6,10 9,08 1,78 11,50 62,43 11,61 2,34 2,20 1,49
3x3 76.2 x 76.2 3/8 9,53 7,20 10,71 2,11 13,60 74,92 13,60 2,31 2,26 1,47
3x3 76.2 x 76.2 1/2 12,7 9,40 13,99 2,75 17,70 91,56 18,03 2,29 2,36 1,47
2 1/2x2 1/2 63.5 x 63.5 1/8 3,18 2,08 3,10 0,61 3,93 15,81 3,45 2,00 1,70 1,24
2 1/2x2 1/2 63.5 x 63.5 3/16 4,76 3,07 4,57 0,90 5,80 22,89 4,92 1,98 1,75 1,24
2 1/2x2 1/2 63.5 x 63.5 1/4 6,35 4,10 6,10 1,19 7,66 29,13 6,39 1,95 1,82 1,24
2x2 50.8 x 50.8 1/8 3,18 1,65 2,46 0,48 3,09 7,91 2,13 1,60 1,39 1,01
2x2 50.8 x 50.8 3/16 4,76 2,44 3,63 0,71 4,57 11,24 3,14 1,57 1,44 0,99
2x2 50.8 x 50.8 1/4 6,35 3,19 4,75 0,94 6,07 14,57 4,10 1,55 1,49 0,99
1 3/4x1 3/4 44.45 x 44.45 1/8 3,18 1,44 2,14 0,42 2,72 5,24 1,62 1,39 1,23 0,88
1 3/4x1 3/4 44.45 x 44.45 3/16 4,76 2,12 3,15 0,62 4,01 7,45 2,36 1,36 1,29 0,87
1 3/4x1 3/4 44.45 x 44.45 1/4 6,35 2,77 4,12 0,81 5,25 9,45 3,05 1,34 1,34 0,87
1 1/2x1 1/2 38.1 x 38.1 1/8 3,18 1,23 1,83 0,36 2,32 3,33 1,15 1,19 1,06 0,76
1 1/2x1 1/2 38.1 x 38.1 3/16 4,76 1,80 2,68 0,53 3,42 4,58 1,64 1,17 1,11 0,74
1 1/2x1 1/2 38.1 x 38.1 1/4 6,35 2,34 3,48 0,69 4,45 5,83 2,13 1,14 1,19 0,74
1x1 25.4 x 25.4 1/8 3,18 0,80 1,19 0,23 1,48 0,83 0,49 0,76 0,76 0,50
1x1 25.4 x 25.4 3/16 4,76 1,16 1,73 0,34 2,18 1,25 0,66 0,76 0,81 0,48
1x1 25.4 x 25.4 1/4 6,35 1,49 2,22 0,44 2,84 1,78 0,98 0,74 0,86 0,50
Tabla 16. Propiedades Geométricas de los Ángulos
Dimensiones Espesor "t" Peso Area Ejes XX-YY
Perfiles
Designación
h s r1 r2 x=y w z Ix Sx rx Iw Sw rw Iz Sz rz
mm mm mm mm mm mm mm mm² kg/mt 10³mm4 mm3 mm 10³mm4 mm3 mm 10³mm4 mm3 mm
L 2.5 x 19 19,00 2,50 4,00 2,00 5,50 13,20 7,80 90,00 0,71 2,80 210,00 5,60 4,50 340,00 7,10 1,10 140,00 3,50
L 2.5 x 25 25,00 2,50 4,00 2,00 7,00 17,70 9,90 120,00 0,95 6,80 380,00 7,50 11,00 620,00 9,50 2,60 270,00 4,70
L 2.5 x 38 38,00 2,50 6,00 3,00 10,00 26,90 14,10 188,00 1,47 24,70 880,00 11,50 40,20 1.500,00 14,60 9,20 650,00 7,00
L 3 x 19 19,00 3,00 4,00 2,00 2,70 13,40 8,10 106,00 0,83 3,30 250,00 5,60 5,30 390,00 7,00 1,30 160,00 3,50
L 3 x 25 25,00 3,00 4,00 2,00 7,20 17,70 10,20 142,00 1,11 8,00 450,00 7,50 12,80 730,00 9,50 3,20 310,00 4,70
L 3 x 30 30,00 3,00 5,00 2,50 8,40 21,20 11,90 173,00 1,36 14,10 650,00 9,00 22,80 1.070,00 11,50 5,50 460,00 5,60
L 3 x 38 38,00 3,00 6,00 3,00 10,30 26,90 14,60 222,00 1,74 29,50 1.070,00 11,50 47,70 1.770,00 14,70 11,30 780,00 7,10
L 4.5 x 25 25,00 4,50 4,00 2,00 7,80 17,70 11,10 206,00 1,62 11,10 650,00 7,40 17,60 1.000,00 9,30 4,70 420,00 4,70
L 4.5 x 30 30,00 4,50 5,00 2,50 9,00 21,20 12,80 252,00 1,98 19,90 950,00 8,90 31,80 1.500,00 11,20 8,10 630,00 5,70
Tabla 17. Perfiles en L
Dimensiones y propiedades para el diseño
Dimensiones
Area Peso
Propiedades Elásticas
Altura=Ala Radios Eje X-X = Y-Y Eje W-W Eje Z-Z
-
-
Perfiles
MEDIDAS HxB Kg./m kg./unid. 6 m unid/paquete 6 m AREA cm² MEDIDAS HxB Kg./m kg./unid. 6 m unid/paquete 6 m AREA cm²
1/8 x 1/2 0,32 1,92 560 0,40 1/2 x 1 2,53 15,18 70 3,23
1/8 x 5/8 0,40 2,40 450 0,50 1/2 x 1.1/2 3,8 22,80 45 4,84
1/8 x 3/4 0,48 2,88 375 0,60 1/2 x 2 5,07 30,42 34 8,45
1/8 x 1 0,63 3,78 280 0,81 1/2 x 2.1/2 6,33 37,98 28 8,06
1/8 x 1.1/4 0,79 4,74 225 1,01 1/2 x 3 7,6 45,60 24 9,68
1/8 x 1.1/2 0,95 5,70 180 1,21 1/2 x 4 10,13 60,78 17 12,90
1/8 x 2 1,27 7,62 140 1,61 1/2 x 5 12,66 75,96 14 16,13
1/8 x 2.1/2 1,58 9,48 112 2,01 1/2 x 6 15,2 91,20 11 19,35
1/8 x 3 1,90 11,40 91 2,42
3/16 x 1/2 0,48 2,88 375 0,60
3/16 x 5/8 0,60 3,60 300 0,76
3/16 x 3/4 0,71 4,26 240 0,91
3/16 x 1 0,95 5,70 180 1,21
3/16 x 1.1/4 1,19 7,14 150 1,51
3/16 x 1.1/2 1,43 8,58 120 1,81
3/16 x 2 1,90 11,40 90 2,42
3/16 x 2.1/2 2,38 14,28 75 3,02
3/16 x 3 2,85 17,10 60 3,63
3/16 x 4 3,80 22,80 45 4,84
1/4 x 1/2 0,64 3,84 280 0,81
1/4 x 5/8 0,79 4,74 225 1,01
1/4 x 3/4 0,95 5,70 180 1,21
1/4 x 1 1,27 7,62 140 1,61
1/4 x 1.1/4 1,59 9,54 110 2,02
1/4 x 1.1/2 1,90 11,40 90 2,12
1/4 x 2 2,53 15,18 70 3,23
1/4 x 2.1/2 3,17 19,02 56 1,03
1/4 x 3 3,80 22,80 45 4,84
1/4 x 4 5,07 30,42 34 6,45
3/8 x 1 1,90 11,40 91 2,42
3/8 x 1.1/2 2,85 17,10 60 3,63
3/8 x 2 3,80 22,80 45 4,84
3/8 x 2.1/2 4,75 28,50 36 6,05
3/8 x 3 5,70 34,20 30 7,25
3/8 x 4 7,60 45,60 24 9,67
Tabla 18. Platinas
.
-