PCM600 v2.4 - Product Guide 1MRS756448_ENg

16
Protection and Control IED Manager PCM600 Product Guide

Transcript of PCM600 v2.4 - Product Guide 1MRS756448_ENg

Page 1: PCM600 v2.4 - Product Guide 1MRS756448_ENg

Protection and Control IED ManagerPCM600Product Guide

Page 2: PCM600 v2.4 - Product Guide 1MRS756448_ENg

Contents

1. Description...........................................................3

2. Tool variants.........................................................4

3. Connectivity packages.........................................4

4. Graphical application configuration.....................5

5. Signal matrix.........................................................6

6. Graphical display editor.......................................6

7. Hardware configuration........................................6

8. Parameter setting.................................................7

9. Signal monitoring.................................................7

10. Event viewer........................................................7

11. Disturbance handling..........................................7

12. Communication configuration.............................8

13. Project explorer...................................................8

14. User management...............................................8

15. Integrated help menus........................................8

16. Data transfer........................................................8

17. System requirements..........................................8

18. Selection table and ordering data.....................10

19. Document revision history.................................10

Disclaimer

The information in this document is subject to change without notice and should not be construed as a commitment by ABB Oy. ABB Oy assumesno responsibility for any errors that may appear in this document.

© Copyright 2011 ABB Oy.

All rights reserved.

Trademarks

ABB and Relion are registered trademarks of ABB Group. All other brand or product names mentioned in this document may be trademarks orregistered trademarks of their respective holders.

Protection and Control IED Manager 1MRS756448 GPCM600Product version: 2.4 Issued: 2011-04-08

2 ABB

Page 3: PCM600 v2.4 - Product Guide 1MRS756448_ENg

1. Description

The Protection and Control IED ManagerPCM600 tool provides versatile functionalities

for the entire life-cycle of all Relion®

protection and control IED applications, at allvoltage levels. This easy-to-handle tool helpsthe user to manage your protection andcontrol equipment all the way fromapplication and communication configurationto disturbance handling, including automaticdisturbance reporting.

Designed to communicate, PCM600 interactswith IEDs over the fast and reliable TCP/IPvia corporate LAN or WAN, or alternatively

directly through the communication port atthe front of the IED. PCM600 tool is able toread and write all configuration and settingdata of an IED with a single command.

The user interface, workflow and the IEC61850-based data model in PCM600 aredesigned according to the same philosophy

as the Relion® protection and control IEDs,ensuring smooth and seamless integrationbetween the tool and the IEDs.

PCM600 also secures the projects and datacreated with earlier versions of the PCM600tool, which enables full backwardscompatibility.

GUID-BC9474F6-E579-4326-99E8-433B8A3FEB99 V1 EN

Figure 1. PCM600 connected locally or remotely to IEDs

Protection and Control IED Manager 1MRS756448 GPCM600Product version: 2.4 Issued: 2011-04-08

Revision: G

ABB 3

Page 4: PCM600 v2.4 - Product Guide 1MRS756448_ENg

2. Tool variants

PCM600 is available in three variants:PCM600, PCM600 Engineering and PCM600

Engineering Pro. PCM600 Engineering Proincludes PCM600 Engineering functionality,which again includes PCM600 functionality.

Table 1. Supported functions per tool variant

Function PCM600 PCM600Engineering

PCM600Engineering

Pro

Signal matrix ● ● ●

Parameter setting ● ● ●

Communication management ● ● ●

Disturbance handling ● ● ●

Signal monitoring ● ● ●

Event viewer ● ● ●

Creating/Handling projects ● ● ●

IED user management ● ● ●

XRIO parameter export/import ● ● ●

Graphical display editor ● ● ●

Hardware configuration ● ● ●

User management ● ● ●

Graphical application viewing ● ● ●

Graphical application configuration - ● ●

IEC 61850 communication configuration,incl. GOOSE

- - ●

3. Connectivitypackages

PCM600 incorporates ABB’s connectivitypackage concept, which simplifies protectionengineering and reduces the risk of errors.The Connectivity Packages which aredownloadable from ABB’s web portal,available on CDs or using the UpdateManager tool in PCM600 make configurations

and IED data readily available to the PCM600tool. The packages further contain acomprehensive description of the IED,including data signals, parameters, protocoladdresses and IED documentation.

Protection and Control IED Manager 1MRS756448 GPCM600Product version: 2.4 Issued: 2011-04-08

4 ABB

Page 5: PCM600 v2.4 - Product Guide 1MRS756448_ENg

4. Graphical applicationconfiguration

The state-of-the-art graphical applicationconfiguration functionality offers powerfulways to create, adapt and modify applicationconfigurations, which also can be made astemplates for later re-use. PCM600 alsoenables presentation of the whole signal flowfrom input to output. It also assists the userduring the creation of applicationconfiguration through colour indications ofthe function blocks to ensure that themandatory inputs have been correctlyconnected. Before writing the configurationto an IED, the tool offers validation of thecomplete IED configuration which ensuresthat the configuration does not contain errors.

Additionally, the user can compare theconfiguration in the tool to the one in theIED. Further, the signal status on-linemonitoring functionality helps to verify thereal-time processes in the IED, which isextremely useful for troubleshooting.

GUID-62510AC1-D402-425C-A00D-FD0B97138922 V2 EN

Figure 2. Application configuration, Onlinemonitoring

GUID-A565A681-95ED-4CEC-B721-DD119BEBE400 V2 EN

Figure 3. Application configuration, visualindication of the configuration

Protection and Control IED Manager 1MRS756448 GPCM600Product version: 2.4 Issued: 2011-04-08

ABB 5

Page 6: PCM600 v2.4 - Product Guide 1MRS756448_ENg

5. Signal matrix

The graphical signal matrix of PCM600 allowsthe user to efficiently connect CTs, VTs,binary input and output signals to theconfiguration. The configuration can also bechanged from here. The tool can also be usedfor connecting the LEDs on the IED as wellas for connection of the GOOSE signalsbetween the IEDs.

In addition to the standard functions ofPCM600, the Engineering Pro variant offersmeans to connect the GOOSE (GenericObject Oriented Substation Events) signalsbetween the IEDs. In a system based on IEC61850, GOOSE messaging is used for timecritical messages.

Once the IEDs have been configured andparameterized, PCM600 enables theconfiguration of the horizontal bay-to-baycommunication for station-wide interlocking,and sends the complete IED description to asystem engineering tool.

GUID-ADD28079-AE48-4C38-BA28-138FDEE21977 V1 EN

Figure 4. Signal matrix tool view

6. Graphical displayeditor

The graphical display editor is used forconfiguring the display of an IED. Thegraphical display consists of one or morepages. A display page contains the drawing

area where the actual display configuration ismade. A display is configured by draggingpredefined graphical symbols from a libraryonto the drawing area. The directed link toolcan be used to draw connections betweensymbols. Every symbol type has acorresponding representation in both theANSI and the IEC symbol palettes. Symbolscan be connected to the applicationconfiguration.

GUID-3248B496-F627-44AD-9261-ABB812508CAA V1 EN

Figure 5. Graphical display editor,configuring the display of an IED

7. Hardwareconfiguration

The hardware configuration can be used toget a quick overview of an IED and to add orchange hardware modules. It is possible toview the front and back of the IED includingcard information and their slot position.Furthermore it is possible to compare thehardware configuration used in the tool tothe actual one in the IED.

Protection and Control IED Manager 1MRS756448 GPCM600Product version: 2.4 Issued: 2011-04-08

6 ABB

Page 7: PCM600 v2.4 - Product Guide 1MRS756448_ENg

8. Parameter setting

The parameter setting of PCM600 allows theuser to view and set IED parameters offline(stored in the tool) and online (stored inboth, tool and IED). The parameters can beread from the IED to PCM600 or written fromPCM600 to the IED while the IED is inservice. In addition, the user can export andimport the parameters for test sets in XRIOformat (e.g. Omicron Test Universe).

The parameter setting function can be usedin two different modes. The normal modeallows the IED protection engineer to quicklyview and change the most commonly usedparameters, whereas the advanced modeunveils all parameters that can be set.

PCM600 further offers a filtering functionallowing the user to view all IED parametersor the parameters related to a specificfunction block. In addition, the user canchoose to only view parameters that havebeen changed or parameters with valuesdeviating from the IED’s setting. Changedparameters with different values in the tooland in the IED are clearly indicated.

GUID-C054605B-7CC8-431C-A4F2-07797F7B5518 V1 EN

Figure 6. Parameter setting view

9. Signal monitoring

The signal monitoring function provides theuser with online information about the

measured values and displays the status ofbinary input and output signals of an IED.Furthermore, PCM600 facilitatescommissioning and testing of physicalconnections via the signal monitoring tool(forcing of signals).

10. Event viewer

The event viewer of PCM600 enables the userto view the IEDs’ sequence of eventsinformation including timestamps. The eventlog facilitates detailed post-fault analyses offaults and disturbances.

11. Disturbance handling

PCM600 offers effective handling andmonitoring of disturbance records from theIEDs. The disturbance files stored in thestandard COMTRADE format allow the userto view the disturbance record usingWavewin™ software or any commerciallyavailable disturbance analyzer supporting theCOMTRADE format. If required, the reportlayout and contents can be adapted to user-specific needs.

By means of the task scheduler of PCM600,the records can be set to be automaticallyread from the IED. The task scheduler is anindependent process and does not requirePCM600 to be activated. After receiving thefile, PCM600 automatically creates adisturbance report, which can immediately beforwarded to subscribers by e-mail. Such anotification shortens the time fromdisturbance detection to corrective action.

Protection and Control IED Manager 1MRS756448 GPCM600Product version: 2.4 Issued: 2011-04-08

ABB 7

Page 8: PCM600 v2.4 - Product Guide 1MRS756448_ENg

12. Communicationconfiguration

PCM600 incorporates two communicationtools: the communication management tooland the communication configuration tool.

The communication management tool is usedto configure the following protocols for anIED: DNP3, IEC 60870-5-101/103/104 or

Modbus®. The communication configurationtool, available in PCM600 Engineering Pro, isused for configuring the IEC 61850 substationcontrol or inter-bay communication.

13. Project explorer

The project explorer can be used to navigateto the used IEDs within a project / substationand furthermore within an IED to navigate tothe different functionality of an IED. The useris able to create a plant structure with asubstation, voltage levels, bays and IEDs.

New IEDs can also be created by use of IEDtemplates. This enables the reuse of existingIED configurations. IEDs, bays, voltage levelsor a whole substation can be copied andpasted in the plant structure. Selection of aspecific IED in the project explorer givesaccess to the IED’s tools. The function ofimporting and exporting descriptions of IEC61850 substation configurations, configureddevices and device functionality allowsinformation to be shared with otherengineering and system integration tools. Byusing the filtering feature of the projectexplorer the user can filter information ofother tools according to the selection made.

14. User management

PCM600 tool supports access managementboth for the tool and the IEDs. The useraccounts in PCM600 can be linked toWindows user accounts or be defined asseparate user accounts for PCM600. The usermanagement feature allows the administratorto create user groups with different accessrights and profiles.

The access management for the IEDs can beenabled or disabled with the IED usermanagement tool in PCM600. This tool is alsoused for setting and changing passwords forthe IED’s different user levels.

15. Integrated helpmenus

All the necessary instructions for using thetool are integrated in PCM600. Contextsensitive help menus and tool tips providethe user with information about the selectedtools. The IED documentation and guidesavailable from the connectivity package canbe directly accessed from the help menus.

16. Data transfer

PCM600 offers improved data transferbetween the IEDs and the IED managementtool. The IEDs can be accessed remotelyusing the TCP/IP protocol via a local areanetwork (LAN) and standard Ethernet cables,a secured wide area network (WAN), asecured wireless network (WLAN) or, locally,using the IEDs’ front communication port.

Protection and Control IED Manager 1MRS756448 GPCM600Product version: 2.4 Issued: 2011-04-08

8 ABB

Page 9: PCM600 v2.4 - Product Guide 1MRS756448_ENg

17. System requirements

Table 2. Hardware requirements

Hardware Minimum Recommended

CPU 1.0 GHz 2.2 GHz

RAM 1 GB 3 GB

Free hard disk space 2 GB 4 GB

Monitor 1024 x 768 1280 x 1024

Ethernet port required required

Table 3. Supported operating systems

Operating system Version

Microsoft Windows XP Professional 32-bit SP3 or later

Microsoft Windows Server 2003 32-bit SP2

Microsoft Windows Vista Business 32-bit SP2

Microsoft Windows 7 Professional 32-bit

Table 4. Communication

Protocols

TCP/IP via LAN or WLAN

Serial Port (RS-232) or USB/RS-232 converter if SPA based communication is used

Opto/electrical (RS-232) cable for front communication if SPA based communication is used

Protection and Control IED Manager 1MRS756448 GPCM600Product version: 2.4 Issued: 2011-04-08

ABB 9

Page 10: PCM600 v2.4 - Product Guide 1MRS756448_ENg

18. Selection table andordering data

The selection table can be used to choose theright tool variant for an IED – for the latest

supported IEDs please visit www.abb.com/substationautomation

To order PCM600, PCM600 Engineering orPCM600 Engineering Pro, use the orderingdata in the ordering code table.

Sign

al m

atrix

Para

met

er se

tting

Com

mun

icat

ion

man

agem

ent

Dis

turb

ance

han

dlin

g

Sign

al m

onito

ring

Even

t vie

wer

Cre

atin

g/H

andl

ing

proj

ects

IED

use

r man

agem

ent

Gra

phic

al d

ispl

ay e

dito

r

Gra

phic

al a

pplic

atio

n vi

ewin

g

Gra

phic

al a

pplic

atio

n

IEC

618

50 c

omm

unic

atio

n

670 series ● ● ● ● ● ● ● ● ● ● ● ● ●

650 series ● ● ● ● ● ● ● ● ● ● ● ● ●

630 series ● ● ● ● ● ● ● ● ● ● ● ● ●

620 series ● ● ● ● ● - ● ● ● - ● ● ●

615 series ● ● ● ● ● - ● ● ● - ● ● ●

610 series - ● - ● ● - ● ● - - -RE_541/543/545 - ● - ● ● ● ● - - - -REF 542plus - ● - ● - - ● - - - -REX 521 - ● - ● ● ● ● - - - -SPACOM series 1) - ● - - ● - ● - -

----- - -

PCM600 PCM600 Engineering PCM600 Engineering Pro

1) SPAD 346 C, SPAJ 140 C, SPAJ 141 C, SPAJ 142 C, SPAJ 144 C, SACO 16D1, SACO 16D3 and SACO 64D4

-----

GUID-7C235241-02C5-4F43-A0D4-F3F0D1812EEE V4 EN

Figure 7. Selection table

Table 5. Ordering codes

Product Order number

PCM600 Ver. 2.4 (Base version) PCM600-24

PCM600 Engineering Ver. 2.4 PCM600E-24

PCM600 Engineering Ver. 2.4 - Packagelicense of 10 single licenses

PCM600E-24-M10

PCM600 Engineering Pro Ver. 2.4 PCM600EP-24

PCM600 Engineering Pro Ver. 2.4 - Packagelicense of 10 single licenses

PCM600EP-24-M10

Protection and Control IED Manager 1MRS756448 GPCM600Product version: 2.4 Issued: 2011-04-08

10 ABB

Page 11: PCM600 v2.4 - Product Guide 1MRS756448_ENg

19. Document revision history

Document revision/date Product version History

A/2007-12-20 2.0 First release

B/2008-05-30 2.0 SP1 Content updated

C/2009-03-03 2.0 SP2 Content updated

D/2009-07-06 2.1 Content updated tocorrespond to the productversion

E/2009-11-23 2.2 Content updated tocorrespond to the productversion

F/2010-05-28 2.3 Content updated tocorrespond to the productversion

G/2011-04-08 2.4 Content updated tocorrespond to the productversion

Protection and Control IED Manager 1MRS756448 GPCM600Product version: 2.4 Issued: 2011-04-08

ABB 11

Page 12: PCM600 v2.4 - Product Guide 1MRS756448_ENg

12

Page 13: PCM600 v2.4 - Product Guide 1MRS756448_ENg
Page 14: PCM600 v2.4 - Product Guide 1MRS756448_ENg
Page 15: PCM600 v2.4 - Product Guide 1MRS756448_ENg
Page 16: PCM600 v2.4 - Product Guide 1MRS756448_ENg

Contact us

ABB OyDistribution AutomationP.O. Box 699FI-65101 VAASA, FinlandPhone +358 10 22 11Fax +358 10 22 41094

ABB ABSubstation Automation ProductsSE-721 59 Västerås, SwedenPhone +46 (0) 21 32 50 00Fax +46 (0) 21 14 69 18

www.abb.com/substationautomation

1MR

S75

6448

Cop

yrig

ht 2

011

AB

B. A

ll rig

hts

rese

rved

.