p³b operating instructions - Murrplastik...

ACS labelling systems

p³b

operating instructions

As of June 2017 8902865309

2

p³b operating instructions Index

1 Copyrights and Trademarks ............................................................. 4

2 Important hints ................................................................................ 4

3 Safety instructions ........................................................................... 5

3.1 Intended use .................................................................................... 5

3.2 Not intended use ............................................................................. 6

3.3 Choosing an installation site ............................................................ 6

3.4 Using the device .............................................................................. 7

3.5 Ink cartridge handling ...................................................................... 9

3.6 Repairing the unit .......................................................................... 10

3.7 Radio interference ......................................................................... 11

4 Scope of delivery ........................................................................... 12

5 Unit overview ................................................................................ 13

6 Control panel ................................................................................. 14

7 Take the printer into operation ..................................................... 16

7.1 Set up and connect the printer ..................................................... 16

7.2 Install the ink cartridges ................................................................ 17

7.3 Install and replace the chip bars .................................................... 18

8 Installation for access via USB cable .............................................. 20

8.1 Information about the printer driver ............................................ 20

8.2 Installing the printer driver for USB access ................................... 21

9 Installation for access via network ................................................ 23

9.1 Installing the software EpsonNet Config® ..................................... 23

3

9.2 Assign network settings with EpsonNet Config® ........................... 26

9.2.1 Prepare for access via network cable ............................................ 26

9.2.2 Prepare for access via wireless LAN .............................................. 29

9.3 Information about the printer driver ............................................ 31

9.4 Install the printer driver for network access ................................. 32

9.5 Change the printer name .............................................................. 34

10 Driver settings in Windows®.......................................................... 36

11 Settings in the ACS software ......................................................... 41

11.1 Tags output .................................................................................... 41

11.2 Sheet Labels output - Monomatt .................................................. 43

11.3 Sheet labels output - Labels .......................................................... 44

12 Assembling the base plates / printing ........................................... 47

13 Cleaning and maintenance ............................................................ 48

13.1 Cleaning the printer ....................................................................... 48

13.2 Replacing the waste ink tank ......................................................... 48

13.3 Replacing the waste ink absorber ................................................. 49

13.4 Ink pads are used up ...................................................................... 50

14 Contact .......................................................................................... 50

15 Technical data................................................................................ 51

16 Shipping instructions for return .................................................... 52

4

1 Copyrights and Trademarks Windows® is a registered trademark of Microsoft Corporation. Epson® is a registered trademark of Seiko Epson Corporation. All product names used herein are for identification purposes only and may be trademarks of their respective owners. Murrplastik disclaims any and all rights in those marks.

2 Important hints This operating instructions must be read and understood. It must be kept for further use and passed on together with the device.

To operate the mp-PM Basic ACS Gold Studio Software 2.3.0.95 and Windows® Vista SP2 or higher is required. Before putting the device into service read the safety instructions in chapter 3!

5

3 Safety instructions When using the p³b the following basic safety precautions must be observed to protect against electric shock, injury and fire.

Please read and observe all these hints carefully before putting the electrical device into operation.

Keep these safety instructions in a safe place.

Only use the electrical equipment in accordance with the regulations and in accordance with the general safety and accident prevention regulations.

3.1 Intended use

• The p³b is predominantly an inscription device for polycarbonate (PC) labels based on inkjet technology.

• The possibility of labelling as well as the respective durability and quality of the inscription with the p³b can only be guaranteed for the labelling material along with the special ink, both approved by Murrplastik.

• Only the approved special ink can be used.

• The labelling is to be carried out using software approved for the p³b. Labels can be printed using black colour only.

6

3.2 Not intended use The possibility of labelling, as well as the durability and quality of the inscription cannot be guaranteed in the following cases. There is no guarantee, no warranty and no support.

• Not provided is labelling of non Murrplastik material.

• Not provided is using of ink not approved by Murrplastik.

• Not provided is labelling by means of software which is not approved by Murrplastik.

• Not provided is labelling of paper.

3.3 Choosing an installation site

• Position the unit on a level, stable surface that is larger than the unit itself. The unit will not operate properly if it is tipped up or tilted.

• Avoid using locations where the printer will be exposed to extreme fluctuations of temperature or humidity. Protect the unit from direct sunlight, excessive light and sources of heat.

• Avoid using sites that might be exposed to impacts or vibrations.

• Keep the unit away from dusty areas.

• Position the unit near to a mains socket, so that no extension cable is required if possible.

• When transporting or storing the printer, it must not be tipped up, stood on one of its sides or turned upside down. Otherwise, the unit may leak ink.

7

3.4 Using the device

While the printer is printing, keep your hands out of the machine and do not touch the ink cartridges. There is a risk of injury!

• Do not move the print head by hand – if you do, you may damage the

equipment.

• Do not block the housing openings.

• Do not cover the housing openings.

• Do not insert any objects into these slots.

• Avoid spilling any liquids onto the unit at all times.

• Always use the power cable supplied with this unit. If a different power cable is used it can potentially cause fires or electrical shocks.

• Connect all parts of the system to mains sockets that have been properly earthed. No mains socket may be used if items of equipment such as photocopiers or fans are already plugged into it, and these units are regularly switched on and off.

• Do not connect the printer to switchable or timer-controlled mains sockets.

• Do not connect socket boards or extension cables in series

• Do not use the computer system near areas of potential electromagnetic interference, such as may be generated by loudspeakers or cordless telephone base stations.

• Note that the type of electricity source used must match the details on the equipment’s label.

• Do not use any power cable if it is damaged.

8

• If you use an extension lead socket with this unit, take care to ensure that the total power consumed by the connected equipment does not exceed the maximum permitted power consumption for the extension lead socket.

• Also take care to ensure that the total power consumed by the equipment connected to a wall outlet does not exceed the maximum permitted power consumption for the affected mains socket.

• Do not attempt to service the device yourself.

• Isolate the unit from mains power and request servicing from a qualified service technician, if any of the following scenarios occur:

- The power cable or plug is damaged.

- Liquids have leaked into the unit.

- The unit has suffered a fall or its housing is damaged.

- The unit is not working properly or its performance is impaired.

• If the printer is operated within Germany, please observe the following:

- The building’s electrical installation must be protected using a circuit breaker (10 A or 16 A), so as to ensure an adequate level of protection against short-circuiting and overvoltage.

- If the mains plug has become damaged, replace the cabling or contact a qualified technician. The fuses built into the mains plug must only be replaced with fuses of the same form factor and the same rated value.

- If you use a cable to connect the printer to a computer or a different piece of equipment, check to ensure the proper alignment of the plug connectors. Each connector can be plugged only when aligned in a certain way. If you try to plug a connector when it is wrongly aligned, then both pieces of equipment connected by the cable may be damaged.

9

• Always turn the unit off by using the power button on the control panel. When you press this key, the mains LED lights up briefly. Do not disconnect the power plug until the mains LED light has gone out.

3.5 Ink cartridge handling

• Always store ink cartridges out of the reach of children. Cartridge contents are not edible.

• If you get ink on your skin, clean it off using soap and water. If ink should get into your eyes, wash it out immediately with plenty of water.

• Shake new ink cartridges four or five times before opening the package.

• After opening the packaging, ink cartridges must not be shaken, since otherwise ink may leak out.

• Use the ink cartridge before the date printed on the packaging.

• Do not attempt to take the ink cartridges apart or to refill them. This can damage the print head.

• Do not touch the green IC chip on the side of the ink cartridge. This can have an adverse effect on normal operation and the printing process.

• The IC chip on this ink cartridge contains a large number of cartridge-specific details, such as e. g. information about the ink cartridge status. This ensures that the ink cartridge can be removed and replaced as many times as necessary. Note, however, that ink is consumed every time a cartridge is inserted into the unit, since the printer always performs a self-test.

• If you remove an ink cartridge in order to use it later, make sure that you protect the ink outlet from dust and dirt, and store the cartridge somewhere near the printer. The ink outlet features a valve, which avoids the need for covers or plugs. If the cartridge comes into contact with an object, however, ink may leak out and cause staining.

10

• Do not touch the ink outlet or the area around it.

• Do not remove or pull on the label, because this may cause ink to leak out.

• Always install an ink cartridge immediately after opening the packaging. If the ink cartridge is unpacked and then left out for a while before being used, it may then be impossible to print with it.

• Always store ink cartridges with the label at the top. Do not store ink cartridges upside down (label at the bottom).

Cartridge ink information:

The inks used in the cartridges are ECO solvent inks. These inks do not release any harmful volatile organic compounds (VOCs) into the workplace. Specialised air purification systems are therefore not required. The use of milder solvent agents in the inks causes less wear on the print heads, and reduces expenditure for servicing and cleaning.

3.6 Repairing the unit

• Do NOT attempt to repair the equipment yourself. The opening or removal of covers can lead to contact with parts conducting dangerous electrical current and other hazards, as well as voiding product warranties. Contact the manufacturer or a customer service point authorised by the manufacturer.

• If the unit has suffered a fall or the housing is damaged, unplug the unit from the mains and contact the manufacturer or a customer service point authorised by the manufacturer. Otherwise there is a risk of electrical shock.

• If the unit becomes unusually hot, starts producing smoke or unusual odours or if you spill liquids onto the equipment by mistake, then you must unplug the unit from the mains immediately. Contact the manufacturer or a customer service point authorised by the manufacturer.

11

• If the unit no longer works properly, although it has been used in accordance with the usage instructions, then configure the unit's settings only as described in these usage instructions. Incorrect changes made to other control elements can damage the unit, and often require time-consuming work to be performed by qualified technicians in order to restore the normal operating condition of the equipment.

In chapter 16 you will find detailed instructions for returning defective devices for repair.

3.7 Radio interference This product complies with Directive EN 55022 (CISPR Publication 22)/Class B. If you connect the equipment to a computer, take care to ensure that you use a USB cable that is not more than 3 m long.

Important information

You will need administrator rights for installing the USB printer driver!

A possible network installation must be carried out by the user's responsible administrator. Since this is a specific installation NO support shall be applied here whatsoever.

12

4 Scope of delivery Upon receipt of the device check the shipment for completeness. Please keep the outer packaging in case the device needs to be sent in for service or repair. Scope of supply:

A Printer with carrier plate and exchangeable base plate B Canopy C 4 Screws D Torx spanner E CD (driver, documentation) F Operating instructions G USB cable H Power cable I Spare waste ink tank J Spare waste ink absorber K Ink cartridges MK + BK L 3 red Chip bars

13

5 Unit overview

1 Control panel See next page.

2 Service flap Open to replace ink cartridges.

3 Carrier plate Holds the base plates for labelling material.

4 Inspection window Lets you check the level of the waste ink tank.

5 Waste ink tank Collects the ink released during initialisation and cleaning procedures.

6 Print head Moves from left to right during printing. Do not move the print head by hand.

7 Cartridge cover Open to replace the cartridges.

8 Ink cartridges Photo Black BK + Matte Black MK only.

9 Canopy

Reverse side

10 Power connection

11 USB port

12 Ethernet connection

14

6 Control panel

12 WLAN connection LED (blue/blue)

Lights up or flashes to indicate the network status or network errors. If both LEDs are out, the printer is not connected to a network.

13 On/Off key (mains power button) Used to switch the printer on or off.

14 Status LED (blue) The operating status of the printer is indicated by the LED (steady or flashing) On: Printer is switched on. Off: Printer is switched off. Flashing: Initialization, still no operation possible.

15 WLAN key Used to set the parameters for a WLAN connection.

16 Network status sheet key Press and hold the key for at least three seconds to print out a sheet with the network status. To apply the sheet, place the p³b label plate reversed (180° rotation).

17 Print job deletion key Press this key while the printer is printing to cancel the print job.

18 Warning LED (red) Lights up or flashes if a problem occurs.

15

19 Ink key

Used to move the print head into the position for replacing the ink cartridges. After replacing the ink cartridges, press the key again to move the print head to its normal working position (far right). Press and hold the key for at least three seconds to carry out print head cleaning.

Before pressing the ink button(1), the drawer must fully be pulled out. If not, a double LED error can occur, which can only be prevented by switching off and on the device.

20 Ink LED (red) Lights up or flashes if ink cartridges are nearly empty and are to be replaced.

21 Extend carrier plate key Press the key to extend the carrier plate out of the printer. Press the key again to retract the carrier plate.

Additional note(1):

Before starting the print head cleaning by the driver, the drawer must be pulled out, as well.

16

7 Take the printer into operation Read the safety instructions for this printer at the beginning of this manual before using the device.

7.1 Set up and connect the printer

1. Attach the canopy. To do so, slide the canopy (2.) from above onto the output opening on the back of the printer. Insert the 4 bolts (3.) and tighten them gently using the supplied Torx spanner.

2. Position the unit at its installation site.

Ensure there is enough room in front of the unit so the carrier plate can extend without being obstructed.

3. Plug the supplied power cable into

the printer’s power cord socket (a). Connect the printer to the PC by plugging the supplied USB cable into the printer’s USB port (b) and an unused USB port on the PC. Alternatively network connection (c)

4. Use the On/Off button (a)

to switch the printer on. The Status LED (b) flashes. The Ink LED (c) lights up when the ink cartridges are missing.

17

5. Open the service flap.

6. Check whether a waste ink tank is installed. The waste ink tank (a) is located behind the inspection window (b) underneath the print head (c). Install if necessary!

7.2 Install the ink cartridges 1. Carefully cut open the ink cartridge pouch and remove the

cartridge. Do not touch the chip on the front edge with your fingers.

2. Remove the round opaque

bung from the cartridge’s air vent. Keep the plug in a safe place. The plugs are needed later when transporting the printer.

3. Press and hold the ink key (a) for about one second. The print head moves to the replacement position. The Status LED (b) flashes.

Before pressing the ink button, the drawer must fully be pulled out.

18

4. Open the service flap and the cartridge cover. Place each ink

cartridge in its correspondently marked cartridge bay (MK/BK) and press it down until you hear it click into place. Close the cartridge cover/service flap.

5. Press and hold the ink key (a)

for about one second. Now the printer starts to prime the ink supply lines. This can take up to three minutes. After this the Status LED (b) remains lit.

Before pressing the ink button, the drawer must fully be pulled out.

7.3 Install and replace the chip bars The colour ink cartridges are substituted by three red chip bars. If a cartridge is 'empty' the appropriate bar must be taken out and inserted again to do a reset for the printer.

Bar 1 – substitute for Yellow + Magenta Bar 2 – substitute for Red + Orange Bar 3 – substitute for Gloss + Cyan

19

Unmounting the chip bars

Press the ink-key to make the cartridge storage/print head move to the left to open the service flap. Open the cartridge cover and remove the red chip bars by moving it a little bit backwards and then draw it straight up.

Before pressing the ink button, the drawer must fully be pulled out. Do not remove the white plugs!

Installing the chip bars Insert the red chip bars straight from top to bottom. When inserted correctly they cannot be moved backward or forward.

Close the cartridge cover and press the ink-key again. The cartridge initialisation starts and the Status LED is blinking. When finished the LED is lighting permanently.

Before pressing the ink button, the drawer must fully be pulled out. Do not remove the white plugs!

20

8 Installation for access via USB cable 8.1 Information about the printer driver

Important information for installation by the administrator!

According to system requirements there are two driver versions available: 32bit and 64 bit drivers. Both versions are available on the CD included but can alternatively be downloaded from the Murrplastik homepage. Before installing resp. downloading make sure whether you have a 32bit or 64bit operating system.

Before the driver installation, the printer must be connected to the PC via a USB cable, and the printer as well as the PC must be switched on. Administrator rights are required for installation.

The driver installation is started by running the appropriate exe file.

The file name can be different to that listed here.

21

8.2 Installing the printer driver for USB access

Start the installation by double-clicking the driver installation file according to your operating system version (32Bit or 64Bit).

Confirm the security prompt of the Windows® user account control with [YES].

Start the driver installation by clicking on [Setup].

Remove both hooks and click on [OK].

22

The language setting of the operating system is assumed and can be changed for the driver at this point. Continue with [OK].

Accept the license agreement. Continue with [OK]. The driver installation will be performed.

Close the window by clicking [OK].

The printer driver has been successfully installed. If you also want to set up access via the network, follow the instructions in chapter 9. If you want to connect the p³b via USB exclusively, proceed with the driver settings (chapter 10).

23

9 Installation for access via network 9.1 Installing the software EpsonNet Config® EpsonNet Config® is used to assign network settings (static IP-adress, subnet mask, default gateway) to a p³b connected via USB port. Administrator rights are mandatory for installation. The installation file is included on the enclosed CD, but can also be downloaded on the Murrplastik homepage as part of the driver package. The installation is started by running the *.exe file.

The file name can be different to that listed here. Confirm the security prompt of the Windows® user account control with <YES>.

Start the installation by clicking on <Setup>.

24

The language setting of the operating system is assumed and can be changed for the installation at this point. Continue with <Next>.

Continue with <Next>.

Accept the license agreement. Continue with <Next>.

25

It is recommended to use the default installation path. Continue with <Next>.

Click <Install>.

Complete the installation by clicking <Finish>.

26

9.2 Assign network settings with EpsonNet Config® 9.2.1 Prepare for access via network cable

With the previously installed EpsonNet Config® tool, the p³b is assigned its network settings (IP address, netmask, gateway).

Before changing the printer port or network environment, make sure the network is working properly.

A static IP address must be assigned to the p³b. Procedure Connect the p³b to the computer directly via a network cable. Switch the p³b and the computer on.

Do not use a switch or hub to set up the network settings.

Start EpsonNet Config® from the shortcut in the Windows® Start menu.

Confirm the security prompt of the Windows® User Account Control with [YES].

Register EpsonNet Config® as an exception in the Windows® Firewall. Confirm the query with [Yes (Y)].

27

The 'EpsonNet Config®' window opens. If the printer SC-P400 Series ≙ p³b is not listed, check whether the p³b is switched on and a direct connection via network cable with the computer is present.

Then click [Refresh].

The printer is displayed in the 'EpsonNet Config®' window.

Assign the displayed printer and click [Configuration].

28

The 'Device Properties' window opens. Change to the 'TCP/IP' – 'Basic' area. Select 'Manual' and enter the IP Address, Subnet Mask and Default Gateway.

Click on [Transmit].

Confirm the configuration with [OK].

Close the message 'Transmission is complete' by clicking [OK].

The p³b has now got its network settings. The device can be addressed via a network connection via network cable after further setup in Windows®.

If no wireless LAN connection is required, close the 'EpsonNet Config®' window via the menu items [Device] – [Quit].

29

If the p³b should be addressed via a wireless LAN, the following steps must be carried out. 9.2.2 Prepare for access via wireless LAN

Condition for access via wireless LAN is a previous configuration for access via network cable (see chapter 9.2.1). Change to the area 'Network' / 'Basic (Wireless)'.

Enter the name of the wireless LAN (SSID). Select the Security Level.

30

Enter the login password (PSK) for the wireless LAN. Click on [Transmit].

Confirm the configuration with [OK].

Close the message 'Configuration successfully completed' with [OK].

Close the 'EpsonNet Config®' window via the menu items [Device] – [Quit].

31

9.3 Information about the printer driver Important information for installation by the administrator! According to system requirements there are two driver versions available: 32bit and 64 bit drivers. Both versions are available on the CD included but can alternatively be downloaded from the Murrplastik homepage. Before installing resp. downloading make sure whether you have a 32bit or 64bit operating system.

Before the driver installation, the printer must be connected to the PC via a network cable, and the printer as well as the PC must be switched on. Administrator rights are required for installation.

The driver installation is started by running the appropriate exe file.

The file name can be different to that listed here.

32

9.4 Install the printer driver for network access Faultless installation is only feasible if the printer has already been assigned its network settings with the EpsonNet Config® Tool.

Start the installation by double-clicking the driver installation file according to your operating system version (32Bit or 64Bit).

Confirm the security prompt of the Windows® user account control with [YES].

Start the driver installation by clicking on [Setup].

Remove both hooks and click on [OK].

33

The language setting of the operating system is assumed and can be changed for the driver at this point. Continue with [OK].

Accept the license agreement. Continue with [OK].

If the p³b is connected to the computer via a network cable and is switched on as well as has been assigned a correct network configuration with the EpsonNet Config® tool, "Network connection" should be selected automatically.

Continue by clicking [OK]

34

Choose EPSON SC-P400… ≙ p³b and click [OK].

Finish the installation by clicking [OK].

9.5 Change the printer name The installed printer is listed in the Windows® 'Devices and Printers' window. If an installation via USB cable has already been carried out, now there is a copy of the EPSON SC-P400, which is the network printer.

35

The name of the network printer must be renamed to Epson SC-P400 Series (Network). Click on the printer with the right mouse button and select 'Printer properties' from the context menu.

The 'Properties…' window of the printer opens. You can change the name of the printer here.

Change the printer name in Epson SC-P400 Series (Network).

Close the windows by clicking [OK].

36

10 Driver settings in Windows® 1. Adjusting the paper size

Open the 'Devices and Printers' window in Windows®. Here the p³b appears as 'EPSON SC-P400 Series' ≙ USB access respectively 'EPSON SC-P400 Series (Network)' ≙ network access.

The name of the printer must not be changed!

The settings for both devices are the same. In this manual, the settings for the "EPSON SC-P400 Series" are described exemplarily.

Click with the right mouse button on the printer and choose 'Printing preferences' from the context menu.

Select size 'A3 297 x 420 mm' in the Paper Settings area.

37

2. Adjusting the print quality

• Epson Premium Glossy

Real good, powerful print. Ink consumption and printing time slightly increased.


The media type 'Epson Premium Glossy' is the default setting after the driver installation. If not, select this setting.

Open the drop-down menu of 'Print Quality' and select 'Quality Options'.

38

Make sure the quality level is set to '5'. Open the drop-down menu of 'Gloss Optimizer' and set it to 'Off'.

Optional setting Removing the hook in 'High Speed' can slightly improve print quality, but increases the print time.

The media settings for 'Epson Premium Glossy' should be finally shown as here.

Finally, close the 'Printing Preferences' window by clicking [OK].

39

• Plain papers

Good, clear print. Moderate ink consumption and optimized print time.


The media type 'Epson Premium Glossy' is the default setting after the driver installation.

Change the media type to 'plain papers'.

Open the drop-down menu of 'Print Quality' and select 'Quality Options'.

40

Make sure the quality level is set to '3'.

Optional setting Removing the hook in 'High Speed' can slightly improve print quality, but increases the print time.

The media settings for 'plain papers' should be finally shown as here.

Finally, close the 'Printing Preferences' window by clicking [OK].

41

11 Settings in the ACS software The new device and its corresponding calibration point (offset) are added/entered in the ACS software. Please note: Depending on whether you are accessing the p³b via USB cable or via network, you must select the 'EPSON SC-P400 Series' respectively the 'EPSON SC-P400 Series (Network)'. The settings must be adjusted separately for each Windows® user.

11.1 Tags output

Start the ACS software, do not open a project and click [Settings] - [Output Device Setup].

If the EPSON SC-P400… is not preselected already in the upper drop-down menu of the Tags output section (red frame), open this drop-down menu and choose the corresponding EPSON SC-P400… ≙ p³b.

42

Click [Add] to take over the device into the 'List of output devices'.

Set a hook at 'As default'.

Change the 'Frames/Row' value into '3'.

Enter the calibration point values X = 33.0 Y = -173.3 Please note These values are default values and can be vary slightly by device.

Check your settings once again and close the window by clicking on [Done].

43

11.2 Sheet Labels output - Monomatt


If the EPSON SC-P400… is not preselected already in the upper drop-down menu of the Sheet Labels output section (red frame), open this drop-down menu and choose the corresponding EPSON SC-P400… ≙ p³b.

Click [Add] to take over the device into the 'List of output devices'.

Set a hook at 'As default'.

44

Enter the calibration point values.

X = 122.3 Y = -9.3

Open the 'Rotation' drop-down menu and choose value '90'.

Please note These values are default values and can be vary slightly by device.

Check your settings once again and close the window by clicking on [Done].

11.3 Sheet labels output - Labels


Please note The settings for 'Sheet labels output – Monomatt' should already be done (chapter 8.2).

45

The device to be choosen has already been selected in chapter 8.2 (Sheet labels output - Monomatt) and added in 'List of output devices'. A hook for 'Standard' has already been set.

Open the 'Calibration Point' drop-down menu and choose the second entry from above '0.0'.

Thereby the coordinate names changes from X / Y into X1 / Y1. The rotation value usually returns to '0'. Please note In comparison to Monomatt the sheet labels calibration points are referenced with X1 and Y1 always.

46

Enter the calibration point values.

X1 = 74.5 Y1 = -123.5

The rotation value is '0'.

Please note These values are default values and can be vary slightly by device.

Close the window by clicking on [Done].

47

12 Assembling the base plates / printing 1. Use the On/Off button (a)

to switch on the printer. The carrier plate (b) with the preassembled exchangeable base plate moves out.

2. Place the base plates (c) on the

exchangeable base plate (b). These are used to position the label plate frames precisely for printing. The carrier plate can hold up to six base plates.

3. Now lay out the label plate

frames (d).

Ensure, that the labels do not tower up. This may cause blocking of the print head during operation respectively down-grade printing results.

4. Retract the carrier plate. To do

so, push the carrier plate gently into the printer until automatic retraction takes place.

Now the printer is ready for printing.

IMPORTANT! The carrier plate must be pushed inside the device BEFORE a print job is sent.

48

13 Cleaning and maintenance In order to keep the printer in good condition and functional, it should be cleaned and maintained periodically, if necessary also more times.

13.1 Cleaning the printer

• Switch off the printer. • Unplug the power cable. • Use a dry, soft cloth to remove dust and other foreign bodies. To remove stubborn dirt, carefully clean the printer using a cloth moistened with water or a neutral detergent. Then dry off the printer thoroughly!

Do not use any aggressive cleaning agents or scourers. These can cause discolouration or deformation of the housing.

Never use pressurised air to clean the device or parts thereof.

13.2 Replacing the waste ink tank Ink that escapes during the cleaning process is collected in the waste ink tank. This tank must be regularly checked and replaced as necessary. Check the waste ink tank: The waste ink tank (a) is located behind the inspection window (b) underneath the print head (c). If you can see that the tank is full, proceed as follows:

49

1. Retract the carrier plate.

To do so, push the carrier plate gently into the printer until automatic retraction takes place.

2. Open the service flap. 3. Turn the waste ink tank

latch to open it. 4. Remove the cap. 5. Carefully remove the full

waste ink tank. 6. Remove the cap from the

empty waste ink tank. 7. Use this cap to close the full

waste ink tank. 8. Insert the empty waste ink

tank into the printer. 9. Attach the cap and turn to

close it.

Dispose of the ink at a local waste management site in accordance with the statutory regulations.

13.3 Replacing the waste ink absorber Any ink that escapes is collected by the waste ink absorber, to avoid soiling the printer or the work surface. You should check the condition of the absorber at regular intervals. Replace if necessary.

50

13.4 Ink pads are used up

The Paper LED and the Ink LED are blinking alternately.

Ink pads are used up and must be replaced. This must be done at the manufacturer. The printer cannot be used until the pads have been replaced.

14 Contact Technical Support

+49 7191 482-2222

[email protected]

51

15 Technical data Printing method Inkjet Print resolution 5760 x 1440 dpi Nozzles per col. 180 Drop size 1,5 picolitres Ink Special ink (ECO solvent) Print cartridges 1) 1x BK Photo Black 1x MK Matte Black 3x chip bars Print volume 2) approx. 600.000 chars per cartridge Print area approx. A3 (carrier plate + 6 base plates) Print speed approx. 90 sec. / print area Input voltage) 110 – 240 V AC Frequency 50 – 60 Hz Power consumption 20 W while printing / 0,3 W power off Temperature (operation) 10 °C – 35 °C Humidity (operation) 20 % – 80 % Unit dimensions W x H x D (63 x 25 x 75) cm Installation space W x D (63 x 75) cm Weight 3) approx. 20 kg / 44 lb Interface USB Network interface 4) Ethernet/WLAN Operating system Windows® (Vista, 7, 8, 8.1, 10) 1) All cartridges are chip-coded! To operate the unit all cartridges as well as the chip bars must be installed.

2) Depends on font size and print quality.

Test settings: ACS Software 2.3.0.95, Modern, Size 24, Normal quality.

3) Weight including ink cartridges and supplied accessories.

4) Ethernet 100 BASE-TX/10 BASE-T - IEEE 802.11b/g/n WPA2 compatible WEP (64/128 Bit)

52

16 Shipping instructions for return In case it becomes necessary to return the p³b for whatever reason (e. g. service, repair) it is essential to observe the following points:

• The device must not be shipped with full waste ink tank. The ink tank must be emptied and reinserted correctly resp. replaced by the empty ink tank supplied. Optionally a piece of absorbent fabric can be placed inside the tank before reinserting it to collect possible remaining drops of ink. The ink must be disposed of properly according to the legal instructions.

• Please re-close the air vents of the ink cartridges with the corresponding plug. After this the cartridges can remain in the printer.

• The device must be switched off correctly with the mains switch to ensure the cartridge unit is moved in its stand-by position to the right correctly. In no case switch off the device by unplugging the mains cable.

• The aluminum base plates (GPx) may remain at the sender. This applies to a possible sheet labels base plate as well. The grey base plate should be fastened additionally with some adhesive tape.

• Unscrew the red canopy and place it in the packaging board as previously supplied (use styrofoam packaging).

• Position the carrier plate as previously supplied as well. • Whenever possible use original packaging (styrofoam parts included)

for return shipments or any equivalent and proper packaging.

• The device must always be shipped in a horizontal position. Any other position is not permitted. Add a corresponding advice on the packaging board.

For any damage or dirt of the device due to failure in observing these instructions there is no liability whatsoever.

Important advice for customers/senders! All return shipments must be in compliance with these instructions.

53

Declaration of European Conformity

54

Notes

Murrplastik Systemtechnik GmbH Dieselstraße 10 71570 Oppenweiler Germany

+49 7191 482-0 [email protected]

www.murrplastik.de

As of June 2017 8902865309

http://www.murrplastik.de/

p³b operating instructions - Murrplastik...

Documents

Transcript of p³b operating instructions - Murrplastik...