Pattern System Instruction

Sock palette Design System Software Operation Manual

Sock palette Design System software

Operation Manual

ZheJiang Minde Automated Equipment Co.

Ltd

Tel: 0571-87995388

Zhejiang Minde Automated Equipment Co.Ltd 1


Contents

PART 1 FILE OPERATIONS.....................................................................................................3

1-1 NEW..................................................................................................................................................3

1-2 OPEN................................................................................................................................................3

1-3 SAVE.................................................................................................................................................4

1-4 SAVE AS...........................................................................................................................................4

1-5 IMPORT BMP FILE............................................................................................................................4

1-6 EXPORT BMP FILE...........................................................................................................................5

1-7 EXIT................................................................................................................................................6

PART 2 GRAPHICS EDITING...............................................................................................6

2-1 REVOCATION....................................................................................................................................6

2-2 REPEAT.............................................................................................................................................6

2-3 SELECT ALL.....................................................................................................................................7

2-4 SHEAR..............................................................................................................................................7

2-5 COPY................................................................................................................................................7

2-6 PASTE...............................................................................................................................................7

PART 3 SOFTWARE INTERFACE TO VIEW THE OPERATION..................................7

3-1 TOOLBAR.........................................................................................................................................7

3-2 STATUS BAR.....................................................................................................................................8

3-3 DRAWING TOOLS..............................................................................................................................8

3-4 VIEW OF LINKAGE............................................................................................................................8

3-5 REFRESH VIEW................................................................................................................................8

PART 4 GRAPHICAL DATA MANIPULATION.................................................................9

4-1 HANAGATA CHECK...........................................................................................................................9

4-2 CONTROL SETTINGS.........................................................................................................................9

4-2-1 SPEED CONTROL SETTINGS.........................................................................................................9

4-2-2 CIRCLE THE NUMBER OF CONTROL SETTINGS...........................................................................10

4-2-3 CHAIN PARAMETERS.................................................................................................................11

4-2-4 MAIN SPINDLE PARAMETERS.....................................................................................................11

4-3 PROPERTIES....................................................................................................................................12

4-4 SYSTEM PARAMETERS....................................................................................................................12

4-5 MAIN SPINDLE CONFIGURATION SETTINGS....................................................................................12

4-6 SELECT MODEL..............................................................................................................................13

PART 5 GRAPHICS WINDOW OPERATION...................................................................13

5-1 RESTORE VIEW..............................................................................................................................13

5-2 FIRST VIEW....................................................................................................................................14

5-3 THE SECOND VIEW.........................................................................................................................14



5-4 THE THIRD VIEW............................................................................................................................15

Part 1 File operations

1-1 new

① When the user clicks on the new menu, Out the following

screen.

② Users to set their own Knitting socks Hanagata after the

width and height. By determining. Software will

automatically generate Drawing the three as the size of

work area, Tim and yarn were the main spindle as well as

the rubber band, For users of the style of the socks used

to draw.



1-2 Open

① When a user clicks to open menu, Out the following screen,

Were Support 4F File (*.DSN). 5F File (*.CTL). 6F File (*.DAT). 6F

－Ⅱ File (*.DAP).

② Selected file types specified above. And in line with my

company's socks data format. Open the software will

automatically parse the file which contains information on a

flower-shaped. And display the drawing in the corresponding

area of work and production control of the flower-shaped

data.

1-3 Save

When a user clicks to open menu，Out the following screen，Were

Support 4F File (*.DSN). 5F File (*.CTL). 6F File (*.DAT). 6F－Ⅱ File (*.DAP). The user needs to choose according to the

corresponding model file，Then save. Attention: If this is the form of open files, Do not jump out of the dialog box,

In accordance with the original file name and path to save

the file Hanagata.

1-4 Save As

When a user clicks to open menu，Out the following screen，Were



Support 4F File (*.DSN). 5F File (*.CTL). 6F File (*.DAT). 6F－ Ⅱ File (*.DAP). The user needs to choose according to the

corresponding model file，Then save.

1-5 Import BMP file

Bitmap import function is drawn in order to save users the time

pattern, Directly to the picture to be drawn into the work of

the region, Users need to pay attention to is the software,

Tim and the main spindle yarn only support 16-color bitmap

file(*.bmp), The band supported the 2-color bitmap file(*.bmp),

Operation are as follows:

① When a user clicks into bitmap menu, Out the following

screen

② Selected after the corresponding picture, Click to open



1-6 Export BMP file

Bitmap export function is to the user like patterns can be

saved, To the next need to use.

① When the user clicks on menu bitmap export, Out the

following screen.

② Save the location of the designated, And write the file

name, Click the Save.

1-7 EXIT

From the functional window is closed software, the end of the

use of this software.

Part 2 Graphics Editing

2-1 Revocation

Revocation refers to the function: When users feel that the



current drawn when there are problems, I would like to return

to a previous state, to carry out the operation to deal with.

2-2 Repeat

Repeat function is the means: When a user that too much time to

deal with withdrawal, would like to go back after the state

of the operation to deal with.

2-3 Select All

Select All function means: When a user that needs the work of

the current operation of selected areas, to carry out the

operation to deal with.

2-4 Shear

Cut refers to the function: When users feel that the selected

region are not satisfied with the need to remove the flower-

shaped, carried out the operation to deal with.

2-5 Copy

The function of reproduction is the means: When a user that the

selected region Hanagata multiple use needs to carry out the

operation to deal with.

2-6 Paste

Paste function means: When the user used the copy function of

shear or picture need to use to carry out the operation to

deal with.



Part 3 Software interface to view the

operation

3-1 Toolbar

Toolbar users refer to the more frequent use of the software

features a combination of the operation are displayed in a

toolbar, as follows.

Including: New, open, save, revocation, repeat, cut, copy,

paste, view, refresh, grid, cross cursor, Hanagata check,

control the speed settings, the control loop a few settings,

the color exchange, color conversion, printing, operating

system information.

3-2 Status Bar

Toolbar means users in the use of software in the current

operating conditions, as follows.

Including:The current state of operation, line number, column

number, color number, the system date and time.

3-3 Drawing tools

Drawing tools to draw Hanagata means of a series of graphics

operations portfolio, as follows.



Including:Selection, eraser, paintbrush, filling, check

color, zoom, straight, rectangular, round, text, 1 on 1

strip, 1 to 1 mesh, floating copy, multi-block replication,

turned around, flipped up and down , around the mirror, flip

mirror.

3-4 View of linkage

Linkage when the drawing view to enlarge the work area to pull

more than 4 times when the scroll bar, Tim yarn work area,

the main spindle work area, work area at the same time band

mobile. User-friendly operations to precise picture.

3-5 Refresh View

Refresh the view to re-work area is to show.

Part 4 Graphical data manipulation

4-1 Hanagata check

① When the user clicks on to export bitmap menu, jump out of the following images to deal with a variety of different

models, it is necessary to check the data-processing

methods are also different.



② When the user select End models, the points identified.

Procedures to check for errors on their own. If you find an

error, we will report the wrong information, as well as the

location of.

③ Inspection at the same time, in the status column will show the progress. To deal with the end, it will also jump out

of the corresponding message.

4-2 Control Settings

4-2-1 Speed control settings

Mainly used for speed control settings weaving machines, each

phase of the speed control, speed control when the user

clicks the menu settings, it will jump out of the following

interface.



4-2-2 Circle the number of control settings

Speed control loop set up primarily for the process of machine

knitting, weaving an area set up the need for repeated

operations, when the user clicks on the control settings

menu lap, it will jump out of the following interface.



4-2-3 Chain parameters

Chain parameters used to control the manufacturing process of

socks, each part of the action needed to set up speed, when

the user clicks on the chain parameter setting menu, it will

jump out of the following interface.



4-2-4 Main spindle parameters

Main spindle parameters set in the weaving process, the ways to

deal with the main spindle for yarn settings. When the user

clicks on the main spindle parameter setting menu, it will


4-3 Properties

Attribute is used to image height and width settings, and a

variety of models the same set of minimum Tim Barracuda yarn

spacing. When the user clicks on the properties menu, it will




4-4 System parameters

System parameters for the user to operate the main work area

drawing some of the details, such as the selection box border

thickness and color, partial view of the proportion of

observation, as well as the timing of the display grid. When

the user clicks on the properties menu, it will jump out of

the following interface.

4-5 Main spindle configuration settings

Main spindle configuration settings is used to configure some

kind of knitting process, the needs of those working shuttle,

as well as the exchange time between the shuttle. When the

user clicks on the main spindle configuration settings menu,

it will jump out of the following interface.



4-6 Select Model

Choice of models refers to the user to create models of socks in

order to generate a flower-shaped paper and machine operators

can match. When the user clicks on the menu choice models, it

will jump out of the following interface.

Part 5 Graphics window operation

5-1 Restore View

Refers to the software to start to restore the view is that the

framework structure, the specific pattern is as follows.



5-2 First View

The first view of the drawing refers to the work area, the only

operation carried out Tim yarn, and the specific pattern is as

follows.

5-3 The second view

The second view refers to the work area of the drawing, the

only operation for the main spindle, and the specific pattern

is as follows.



5-4 The third view

The third view is that this painting refers to the work area,

the rubber band can only be operated by the state, the

specific pattern is as follows.



ZheJiang Minde Automated Equipment Co. Ltd

Address：1A-2F,NO.16,5th Road,Xiyuan,Xihu

Science & Technology

Park,Hangzhou,China

TEL:0571-87995388

FAX:0571-87995388-805

Zip:310030

Web site:www.hzmind.com


Pattern System Instruction

Documents

Transcript of Pattern System Instruction