Passenger Car 1986

MANUFACTURERS MOTOR VEHICLE SPECIFICATIONS

METRIC( U.S. Customary)

Passenger Car

1986 Manufacturer Car Line

FORD MOTOR COMPANY MUSTANG

MaMlng Address P.O. BOX 2053 DEARBORN, MICHIGAN 48121

Issued Revised SEPTEMBER, 1985

Questions concerning these specifications should be directed to the manufacturer whose address is shown above . The information contained herein is prepared, distributed by, and is solely the responsibility of the automobile manufacturing company to whose products it r.elates. This specification form was developed by the automobile manufacturing companies under the auspices of the Motor Vehicle Manufacturers Association of the United States, Inc. The General Specifications herein are those in effect at date of compilation and are subject to change without notice by the manufacturer.

MVMA-C-86

Blank Forms Pl'ovided by Technical Affairs Division

ff'l1WfM Motor Vehicle Manufacturers Association

of the United States, Inc.

MVMA Specifications Form Passenger Car METRIC (U.S. Customary)

Table of Contents

1 2

3-6

4 4

5

6 7

7

8-10

11 12-13

13 14-15 15-16

17 18 18 18

19 20-22

23 24 25 26

27-33

34

NOTE:

Car Models Power Teams Engine

Lubrication System Diesel Information Cooling System Fuel System Vehicle Emission Control

Exhaust System Transmission, Axles and Shafts Suspension-Front and Rear Brakes

Tires and Wheels Steering Electrical Body- Miscellaneous Information Restraint System Frame

Glass Convenience Equipment Car and Body Dimensions Vehicle Fiducial Marks

Lamps and Headlamps Vehicle Mass (Weight) Optional Equipment Differential Mass (Weight) Car and Body Dimensions Definitions - Key Sheets

Index

1. This form uses both SI metric unils and U.S. Customary units. The metric unit of measure is presented first, and the U.S. Custom• ary unit follows in parentheses.

2. UNLESS OTHERWISE INDICATED: a. Specifications apply to standard models without optional equipment. Significant deviations are noted. b. Nominal design dimensions are uSed throughO\Jt these specifications. c . All linear dimensions are in millimeters (inches), and all mass (weight) specifications are in kilograms (pounds).

3. The General Specifications herein are those in effect at date of completion and are subject to change without notice by the manufacturer.

4. Additional Car and Body Dimensions (based in part on SAE J1100 "Motor Vehic le Dimensions") may be available from the manufacturer.

MVMA-C-66


Model Description & Drive Introduction

(FWD/RWDI Dale

% LX-MODEL

2-Door Sedan 10-03 - 85

2-Door 10- 03-85 Convertible

2-Door 10-03-85 Hatchback

% GT- MODEL

2-Door 10- 03 - 85 Convertible

2-Door 10- 03-85 Hatchback

% Rear Wheel Drive (RWD)

MVMA-C-86

c ar Line MJJSTANG Model Year 1986 Issued 9 /85 Revised (• ) _ ___ _

Car Models

Malle, Cat Lil'llt, No . of Designated Max. Trunk/Cargo Series, Body Type Seating Positions loacH< ilograms

(Mlgr's Model Code) (FronVRear) (Pounds)

66B 2/2 45.4 (100)

66B (B2L) 2/2 45.4 (100)

61B 2/2 45.4 (100)

66B (B2L/B8D) 2/2 45.4 (100)

61B (B8D) 2/2 45 . 4 (100)

Page 1

MVMA Specifications Form Passenge r Car METRIC (U.S. Customary)

Car Line MUSTANG Model Year 1986 Issued _..; 9:.l.::.8~5 - Revised(•) ____ _

Power Teams (Indicate whether standard or optiona l) SAE J1349 Net bhp (brake horsepower) and net torque corrected to 7-rF/25• C and 29 .61 In. Hg/100 kPa atmospheric pressure.

ENGINE E X

SERIES SAE Net at RPM h TRANSMISSION AXLE RATIO

AVAILAB ILITY Oispl. Carb . a TRANSAX LE (std. first) Liters wa rrels. Compr . Torque

u (in3) I, etc.) Ratio kW N•m

s t

(bhp ) (lb. ft.) $/0

SO STJ TES/CJ 'iNADA/ J LT TUDE LX Models 2.3 IV 9.5 66 165 s M4WR 3 . 08*, 3 . 45(a) Only$ ( 140) (88) (122) AT3 (C-3) 3.27*, 3. 45 (a)

4200 2600

LX Models 3.8 CF! 8.7 90 278 s AT3 (C- 5) 2.73 Only (232) 2V(b (120) (205) AOD % 3.27*, 3 , 45 (a)

3600 1600

All 5.0 HO EFI 9 . 2 149 386 D M50D 2,73-T, 3. 08-T (302) (200) (285) AOD 3.27 - T

4000 3000

AOD - 4- Spee< Automa 1 ic Ov, rdriv1 AT3 - 3- Speec Se l ect Shift Autom, tic M4WR - 4- Speec Manual M50D - S-Spee1 Manual loverd: ive $ - Except Convert: Ible T - Trac t ic tn-Lok % - Canada !Not Avai lab l e * - Altitu1 e Not Ai ailab· e (a) - Altitui e Only (b) - Availal le Cana, a 0nl )

MVMA-C-86 Page2

CarUne MUSTANG MVMA Specific at ions Form Passenger Car

Model Year 1986 Issued __ 9_/-8=5 __ Revised(•) ____ _

METRI C (U.S. Customary)

ENGINE - GENERAL

Type & dNcriptlon (inllne, V, angle , ftat, location, front. mid, rear. 11w1sverw , lonQiludina1, 90hc:. dohc , ohv , hemi, wedge . pre-camber, etc .)

2 .3L

In l ine, Front, Longitudi nal, (SOHC) Single overhead Can, with Modified Wedge Combustion Chambers

_M_anv_taau_ r_er ___ __ _ __ _ -i~Ford Motor Company No-ol cylinders F O

Stroke

Bore spacing (C / L to CI L)

Cylinder block materia l & mass kg (lbs .)

Cylinder block deck heigM

Dec k clearance (minimum) (above r,r below block) 0 . 178 0.007 Above ~ r hMd material & mass kg (lbs .) ast Iron & 2 .5 54)

Head guket thicllness (compressed)

Minimum c:ombustion chamber total VOiume (Cffl3)

Cy l. no. aystern (lronl to rear)•

L Bani<

R. Bank

56.6

1.09 (0.043)

76.9 1 2 3 4

Firingorder 1 3 4 2 Intake manifold material & mass (kg (weight , lbs .)) Aluminum & 2 . 8 Exhaust manilotd material & mass (kg (weight , lbs. )) Cast Iron 4 • 2 Rec;o.1• 11811ded tuel (leaded, unleedlld. cfie5el) Un 1 e aded Fuel antiknock inde•

6 . 3 9.3

(R + M)

2 87 Minimum Octane TOlal m-esseo engine m.sa (wt) dly''

Engine - Pistons

t.Werial & mus , g (weighl, oz.) • plSlon ody

Engine - Camshaft

178 392 S

Alwninum Alloy - SAE 332 s

C linder Head

3.8L

900v, Front, Longitudinal, (OHV) overhead Valve with Modified Wedge Combustion Chambers

Six 96 . 8 86.0 106.S

234.S 9. 23

61.S - 64 .5

1. 04-1.19 0 .041 -0.047

76 . 8 4 5 6 1 2 3 1 4 2 S 3 6 Aluminum S 11 Cast Nodular Iron 7. 1 1S.6)

Aluminum Alloy

In Block Alloy Iron, Induction

Material & mass kg (weight, lbs.) Hardenable Cast Iron Hardened 4.04 8 9 b

Drive~pe Chain / belt Belt Chain Silent

• Rear of engine - drive tak9011. View from drive lakeoff end to determine left & righl side of engine. ·•OrffMdenginemass(weight)fncludltlhe10110Wing : Front End Dress, All Engine Mounted Components and Flex

Plate ; Excludes Starter and Alternator (a) 188 (415 .4) w/AOD Transmission (b) Also Green Sand Molded & Phosphate Coated

MVMA-C-86 Page3

Car line MUSTANG MVMA Specifications Form Passe nger Car

Model Year_19_8_6 __ _ Issued 9/85

METRIC (U.S. Customary)

ENGINE - GENERAL

Type & delcnplion (lnllne, v. qle, ffal, locaUon , front, mid, rear , transverse, loogiludinal, sohc, done, ohv. hemi, wedge. pre-cambar , n:.)

Manufacturer

No. of cy1indefs

Bore

Stroke

Bore spacing (Ct L to CI L)

Cylinde, block material & mass kg (lbs.)

Cylinder block deck height

Deck clearance (minimum) (above cw below btoc:11)

Cylinder heed material & mass kg (tbs.)

Cylindef htad volume (cm")

Head Q8SQt thicknew (c:ompr8Sled )

Minimum comtluslion ehembef lotal volume (cm>}

Cyl. no. system I L Bank {fn)nt to rear)" I R. Bank

Firing order

Intake manifold material & mass (kg (weight. lbs.))

Exhaust manltcld material & lllaS$ [kg (we;ght , lbs .JI

Recommended flJBI (leaded, unleaded . diesel)

Fuel anliknoc:k indelc (R + M)

2

Total d r8'Sed engine mass (wtl dry ..

Engine - Pistons

Material & mus. g (Wllighl, oz.) - pi8b1 ont,

Engine - camshaft

Material & mass kg (weight, ltMI,)

Olive type Chain/bell

Width / pitch

S.OL

90° v, Front, Langi tudinal, (OHV) Overhead Valve, Modified Wedge Coni>ustion Chambers Ford Mt"ltor IV

Eight 101. 6 (4 . 00) 76 . 2 (3.00) 111 . 3 (4.38) & 56 . 7 (125) Cas t I ron 208. 4 (8.20)

,343 ( , 0135) Above Cast Iron & 20.9 (46 , 0) 62 . 0 - 65 ,0

1.04 - 1. 19 (0 , 041 - 0 04 7)

73 . 4 5 . 6 7. 8 L 2 3. 4 1 3. 7 2 6 5 . 4 8 Al1m1i num & H,.8 (U.O) St,,. ;n 1.,,._._ St<><>l H"'"' ,1.,.,.., P. ~ 4

Unleaded

87 Minimum Octane 244 (536 ,9)

Aluminum Al lo 583 20 56

In Bloc

• Re.- of engine - drive takeoff. View from drive talteOlf end to deMrmine left & rigtfl aide of engine .

(12 0)

Revised(•) ____ _

··oressec:1,ng ,nemass(weight)lnc1ooestnef ollowing: Front End Dress, All Engine Mounted Components and Flex Plate; Excludes Starter and Alternator

MVMA•C·86

MVMA Specifications Form Passenger Car

Car Line _ _;..;MU..;;..;;.ST.;;.;AN;..;;..;.G.;;_ ____ -,-- ____ _ ____ _ _

Model Year 1986 l$$Ued _9_/~8_5 _ __ Revised (• )- -----


Engine Detc rlptlonlCarb. E119I-Code

Engine - Valve System

Hyd raulic ~llers (sld .. opt.. NA)

Valves I Number intake I exhaust

I Head 0 .0. intaka / exhaust

Engine - Connecttng Rods

I 2.3L 3.8L

Standard 4/4 6/6 44/38 45/37

_u_a1_en_a1_&_m_8$$----'-(kg=-.. -'-<we___;;.1g_n1,_1b_s. __ ll ___ ...._F_o_r_.g._e_d_S_t_ee_l""',,__o_._6_3_-_o_. 6_4_( __ 1_. 38- 1. 41) Forged Steel (SAE-1151-M} ( a)

Engine - Crankshaft

Material & mass (kg .. (we igtlt.tbs.Jl Nod. Cast Iron & 15. 48 ( 34, 1) Ned . Cast Iron & 14.06(31 .0) Enc thri ,st taken by bearing (no.) # 3 Numbe r ol main bearings 5 4 seal(mat~a 1• I Front Flourocarbon or Pol v Acrvlic one. two piece 1----- ---~-=-==-=:...=..::===-=-=-==-~:...::..~'-=--=-::..L..::..:.::... _________________ _ design.etc .) I Rear Flourocarbon

Engine - Lubrication System

Normal o il pressure [k?a (psi) at engine rpm) 345 SO @ 2000 RPM 27 -414 40-60@ 2000 RPM Type oil intake (tloating, stationary) Statio ·nar 00 filter system (full How, patt. olher) Full Flow Capacity ol ctcase. less filter•ref~J.L (qt.) 4 73 5

Engine - Dlesel Information (NOT OFFERED)

Diesel eng ine manufacturer

Glow plug. current drain at o-F

Injector I Type nozzle I Opening pressure (k?a (psi ll

?re-chamber design

Fuet in• J Manufa cturer

jection pump I Type

Fuel injection pump drive (belt . chain, gear)

Supplementary vacuum source (rype)

Fuel heater (yflS/no)

Water separator, description (std ., opt.)

Turbo manulaclurar

Oil COOier-type (oil IO engine COOiant: o il to ambient air)

Oil filter

Engine - Intake System

Turbo charger• manufacturer

Super charger • manufacturer

Cna,ge cooler

(a) Weight - .665 - .667 (1.46-1.47)

MVMA•C·86 Page 4


Car Une __ f.lJ_S_T_AN_G ______ _ _______ __ _

Model Year 1986 Issued __ 9+-/ ... 8 ... S __ Revised(•) _____ _

METRtC (U.S. Customary)

Engine 0H crlptlon /C.rb. Engl.,.COde

Engine - Valve System

Hydrauli c ~flers (std., opt., NA)

Valves I Number intake / exhauSI

I Head 0.D. intake / exhaust

Engine - Connecting Rods

Material & mass 11,g .. (..igt,. lbs.I)

Engine - Crankshaft

5.0L

Sta ndard with Roller Tappets 8/8

Forged Steel, 0.55 (1.23)

Material&ma&S(kg.,(weight , 1bs.)l Nodular Cast Iron Alloy, 17.3 (38.2) End thrust 1aken by bearing (no.J # 3 Number o1 main bearings 5 Seal (material, I Front Vi ton, One Piece one, two p,ece ~----- ----ii--::-:-:--- ----::c------,=--o------ --- -- --- --- ------ --- -design . etc.) I Rear Vi ton, One Piece

Engine - Lubrication System

Normal oil pressure (kPa {psi! at erlgine rpmj 276-414 (40- 60) @ 2000 RPM Type oil in1al<e {ttoatlng, stationary) Stationary Shrouded Screen i n Sumo Oil filter system {tuN now, pert, OlherJ Full Flow Capacity of clcase, lass filter-refdl·L (qt.J 4. 7 (5.0) Less 0 . 9 (l.O)

Engine - Diesel Information (NOT APPLICABLE) Diesel engine manutac:tunn

Glow plug . currelll arain at o-F

Jnjedof I Type nozzle 1 ~ning pressure (kPa (psi)I

Pre-<:hamb111 design

Fuel in- I Manutllelurer

jecllon pump I Type

Fuel injection pump drive (ben. chain. gear)

Supplemanuuy vacuum source (type)

Fue l heater (yes.tnol

Water separator. descript ion (std., Opt.)

TurbO manufacturer

Oil cooler-type (oil to angine coolant; oil IO ambiem air)

Oil filler

Engine - Intake System (NOT APPLICABLE) Turbo charger - manufacturer

Super charger • man11rae1urer

Charge coole,

MVMA-C-86 Page4A


CarLine ------,MU,...,...,S..-:T.AN_G _____ -=-,c-::-::,------------ModelYea1 _ _ l9_8_6 _ _ 1ssued __ 9~/_8_5 __ Revised(•) _____ _

METRIC (U .S. customary)

Engine Deac:rlptloniCarb. Engine Code

Engine - Cooling System

Coolant recovery system (S1d., opt .. n.a.)

Coolant till locat ion (rad .. bottle)

Radiator cap relie1 valve pressure {kPa (psi I]

Circulatiori Type (choke, bypass) thermostat

Starts to openat-C (°F)

Type (centri fugal, other)

GPM 1000 pump rpm

Number of pumps

Water Drive (V•belt, other)

pump Bear ing type

Impeller materia l

Housing material

By -pass recirculati0r1 ltype (inter .. ext.)]

Coo!ing With heater-L(qt.)

system With air cond.-L(q t. ) capac ity

Opt. equipment (specily-l(q t.)J

Water jac kets ful l tength ot cy l. (yes . no)

Water all a round cylinder (yes, no)

Water jackets oper, at head face (yes. no)

Std. ,AIC , HD

Type (cross-flow , etc.)

Construction (fin & tube

Radiator mechanical, btaze. ete.)

core Material. mass [kg (wgt , lbs .JI

Width

Height

Thickness

[ 2.3L 3.81

Standard Radiator Fill Radiator Fill· Bott 1 .. Atirl

82. 7-110.3(12-16) (a) 97-127 (14-18) By-Pass Reverse Poooet 87 . 91(188 -1 95) 89.5-127 (193 - 200) Centrifu!!al - Vane 13.1 9 One V-Belt Six Rib Poly V Double Row. Sealed. Ba11 f. ~n11er

Low Carbon Stee l Stamoed Stee l Cast Iron Aluminum Internal 8.2 (8.6) 10.Hl0.7)Plus 1 Srlt- -in Rec 8. 7 (9.21 10.2(10.8JPJ11c:. 1.i:;0t- in RPC N_j_A Yes No Yes No Standard HD & A/C Standard Air. Cross - Flow

Tube and Slit Fin Conner . 5.9 (12 . 9) r. .. "~ 4.9 (lfl C))

623.3 (24 . 5) 6?? 3 (24 S}

453.1 (17 . 81 ,10 1 ( 17 8) 16 , 5(0.65) ?R .9_il_._1_4) 1£. S(0.65) 29.Q( l. 14)

< -

Btl Btl

Fins per inch lO_(A/T) : 9(M/T) 12 1.2w/AT3•]1w_LAOO 10w4T~•Qw/A Brass

OD Radiator end lank mate rial

Std .• elec ., opt. Standard Ootio na l Standard Number of blades & type Four Uneven Ei ght Even Five (flex. ~icl. materia l) (Solid Steel) (P l astic) (Solid Steel) Diamete r & projected width 406.6(16.0) (h ) -i:o& 8(]S :Z) (b} 452(18)668.S(Z.69) --Ratio (fan to crankshaft rev.• 1.05:1 1. 25: 1

Fan Fancutouttype N/A Viscous Clutch Ori,;e type (direct. remote) Direct RPM at idle (elee.) N/A Motor rating (wattage) (elec .) N/A Motor switch (type & tocation)(elec.) N_l_A Sw,tchpoint (temp ., pressure ) (elee.) N/A Fan shroud (material) NIA Plastic

la) 96.5 - 124.1 ( 14-18) with A/C (b) Projected width: Standard - 35 . 3 (1.4); HD & AC - 46 (1.8)

MVMA·C·B6 Pages


Carline _..:.MU,:;;.::STc-=:-.:-AN.:..:..::G:__ ______ _____ ____ _

Model Yeiir _1_9_8_6 __ _ Issued --=9..,/.,.8~5~-Revised(•) __ __ _ _


Engine Delacriptlon/C.t> . e:ngln• Code · S.OL

Engine-Cooling System

Coolant recove,ys ystem (std .. opt .• n .a .) Standard Coolant fi ll location (rad .. bottle) Radiator Radia tor cap rekef valve press ure lkPa [psi)I 97 - 124 (14-18) Circulaliol'I Type (choke. t,ypass) Choke lhermostat

Slarts to open at 'C (°Fl 90 - 93 ( 193- 200) Type (centrifugal. other) Centrifugal GPM 1000 pump rpm Ten Number of pumps One

Water Drive (V•bett, other) Poly V pump Bear ing type Ball & Roll er

Impe ller material Stamped Steel HOU$ing material Aluminum

By-pass recirculat ion [type (inter •. ext.)} External Cooling With heater-L(qt.) 13 . 3 (14.1) syslem Willl air cond.-l (Qt.) 13.3 (14 .1) capacity

Opt. equipmert ts~c ity- L(Ql.lJ NIA Water Jackets tu II length ot cyt. (yes , no) Yes Water all around cylinder (yes, no) Yes Wate r jackets open at head face (yes, no) No

Std .• AIC,HO Standard A/C Type (cross•flow.etc .) Cross - Flow Construction (fin 6 tube

Radiator mecllan ical. braze, e<c.) TuhP _and Slit Fin

core Malerial. mass fkg (wgt . lbs.J) r. --- ·- 5 9 ( 12.9) Width f.22.3 (24.5) Height 4 i;"lj 1 i17.8) Thickl'lffS 29 0 (1 U) Fins per Inch 11 12

Radiator end tank material Brass Std .• elec .• opt. Standard Number ol blades 6 type (flex . .olid, material) 9 . Even . Plastic/Steel Diameter & projected width 461 (18.2) 6 55.9 (2.2) Ratio (fan to crankshaft rev. l 1. 13 : 1

Fan Fancutou tt vpe Clutch Drive type (direct, remote) Direct . Belt RPM at idle (elec.) N/_A Motorrating (wattage ) (elec .) NIA Motor switch (type & location) ( e!ec. ) NIA Swi1ch point (temp ., l)fessure) (elec.) NIA Fan shroud (material) Fi 11 .. ri Po 1 vmi:>r

MVMA-c-s6 Pages A

Car Line MUSTANG MVMA Specifications Form Passenger Car Model Year 1986 Issued 9/8S Revised(•) _ _ _ __ _

METRI C (U.S. Customary)

l!ng lne Desc:rlsrtt.1/C•rt, . Engine COde 2.3L 3.8L

Engine - Fuel System (See $Upplemental page tor details of Fuel Inject ion Supercharger Turbocharger etc ii used)

Induction type: C8fburecor. fuel (Canada-2V Carburetor) Injection system, etc . 1 V Carburetor Centra l Fuel Iniec t ion

M!gr, Carter N/A Choke (type) Auto- Full Electric N/A (Canada-Auto.Electric)

Carbure- Idle spd.•rpm Manual 800 Neutra l NIA tor (spec . neutral

or drive and 750 DR S50-625 DR (Canada-700 DR) propane if Aulomatic

used)

Idle AIF mix. 14.6 : 1 13.9:1 Poirn Of injection (no.) N/A Throttl e Bodv(Canada-NIA1

Fuel Constant. pulse . flow N/A Pulse (Canada -NIA) injection Contro l (electronic, mech. ) N/A Electro nic (Canada-NIA)

System pressure (kPa (psi)) NIA 300 (30.S ) (C<>n<>.-1:i- 111 /A 1 Intake mannold heal control {exl'lau,1 or waler thermostatic or fixed) Water Exh,, 11 st Air cieaner Standard Orv ReDlaceab le Paner Element type Option II NIA Fuel

Type (elec. or mech.l Mechanical P.l ~~~ri~ (Cin~di-M§kh) pump LocaCion (eng .. tank ) Enoine Block Fr<>m<> D:i.i 1 ITn T<>nl.-( ") (r,:an P

PreSS1Jre range ikPa (psi) I 37.9 -44 .8£5.5-6.5) ? 1- ~d ( 3. 1 -4 . 9) ( :i) Canada-Cb) Fuel Tank

Capac ity !refill L (gallonsfJ 58 . 3 (15.4) Location (describe) Behind Rear Axl e Anachment Two Straos with Pin and Looo at Rear. Bolt at Front Mate rial & Mass 1kg (weight lbs)] Steel (Terne Plate) Filer Localion & material Ri11ht Rear Quarter Panel F. Stee l pipe Connection to tank Rubber Seal Fuel line (material) Steel Fuel hOM (material) Rubber(Reinforced) St<>~l /Nvlo n (r""""..1- _c::.t-onl ) Return tin& (material) N/A Stee l /Nyl on(Canada -NIA) Vapor line (material) Nyl on/Steel

Opt. , n.a. NIA Extended

Capacity IL (gallons)) NIA range tank Locat ion & materia l N/A

Attachment N/A Opt..n.a. N/A Capacily {L (gallons)] NIA

Auxitia,y tank Location & material NIA

Attachment NIA Selector swileh or valve NIA Separate lill NIA

(a) In-Tank Pump Only, 275- 310 (40-45) (b) Canada-Engine Mollllted Mechanica l Pump Pressure Range, 41.4-55.2(6.0-8.0)

MVMA-C-86 Page6

g)

MVMA Spec11,cations Form Passenger Car

car Line _ __::MU=S~T.!;:AN=G~----------------Modet Year 1986 Issued __ 9~/'-'8~5.___ Revised (•) ____ _


S.OL

Engine - Fuel System (See supplemental page for details o1 Fuel Injection. Supe rcha,ger, Turbocharger, etc. if used)

Induction type: carbUretor, fuel injection system. etc. Electronic Fuel Injection

Mlgr. N7A

Ctlol<e (type) N/A Carbure- klle spd . -rpm Manual to, (spec. neutral

or drive a'1d N/A propane~ Automatic

used)

Idle ""' m!x. 14 . 6:1 PQint 01 injection (no.) Intake Port . (8)

Fuel Constant, pulse , flow Timed injeetion Control (electronic, meeh.) Electronic

System pressure (kPa (psi)) 270.3 (39.2) Intake manifold heat contrOI (exhaust or water tnermosutlic or fixed) None

Air cleaner Standard Orv. Remote Paner Eleme nt. type Optional NIA Fuel

Type (etec. or mech. ) Electric pump Lgcalion (eng., tank) OnP. p,,mn Svstt>m in F11t>l Tanlr

Pressure range (kPa (psit) NIA

Fuel Tank

Capacity [refill L (gallons)) 58 1 (1S_4 Cial) Location (describe) CI.Al·dnrl Q,.,,.,.. .11.vl.,.

Attachment Two Strans with Pin & Loon at 0°ar. R"lf- o,t- F,-nnt" Material & Man (kg (weight lbs)] Steel (Terne Plate1

Fillet Location & material Ritrht Rear Ouarter Panel 6 "1-.,.,,1 pipe Connection to 1111'11< Rubber Seal Fuill line {material) St,,..,.l Fuel hose (malerialj Rubber (ReinforcP.,fl Return Mne (material) Nvlo n IS to<> 1 Vapor line (material) Nvl nn/Sto-,1

Opt.,n .a. NH Exlended

Capacity (L (gallons)) NI.II. range tank Location & material NI.II.

Attachment NIA Opt., n.a. Nit. Capacity IL (gallons)( )J / ,\

Av•~iary Location & material N/A tank Attachment N/A Selector switch or valve N/A Separate fill N/A

MVMA-C-86 Page 6 A


Car Line _ _:MU~S~T~AN:....::..;...::G ____ -:::-:-::-:---- --------Modet Year_1_9_8_6 ___ Issued -~·g_/_8_5 __ Revised(•) _____ _


Engine 0ncrlptlon/Cub , Engine Code

Vehicle Emission Control

Type (air injection. engine modil ications, othef)

Pump or pulse

Driver, by Air Air distribution tnjection {head , manifold , etc .)

Point ol eritry

Type (controlled !low,

Exhaust Exhaust open o,ifice. other)

Emission Gas Exhaust source

Control Recilcula-tion Point of exha ust injection

(spacer, caibunitor , manifold , other)

Type

Numberol

Catalytic Converter Location(s)

Volll!Tle [L (in')I

Substrate lype

Type (ventilates to atmosphere, induction system, other)

Crankcase Energy source (manifold vacuum. carburetor, other)

Emission Control Discharr,s (to intake

manilot , other)

Air inlet (brealher C8J) , Olher)

Evapora, Vapor vented to I Fuel tank live (crankcase , I Carburetor Emission canister other• C0111ro1 Vapor storage provision

Electronic Close<! loop (yeslno) system Open loop (yes•no)

Engine - Exhaust System

Type (single. single with cmss-over . dual. Olher)

Muffler no. & type (reverse flow. straitt thru. separate resonator) Material & Mass kg (weight lb$))

Resonator no. & type

Branch o.d .. wall thickness Exhaust

Main o.d., wall thickness pipe

Material & Mass [kg (weight lbs)I

Inter- o.d. & wal l thickness mediate

Material & Mass {kg (weight lbs)I pipe

Tail o.d . & wall thickness pipe Material & Mass [kg (weight lbs)I

MVMA-C-86

2.31

Vehicle & Engine Modifications, Exhaust Gas Recirculation; Air Injection Pump V-Belt Cylinder Head and Exhaust System Exh. Port in Cyl. Hd •• Catalvst

Controlled Flow External Tube

Soacer TWC + coc Brick Transve-rc:. .. One

Underbodv 1 1 (66) + 1 3 (78) Coat..,.l r.P.rami" Mnnnl i t:h

Closed Induction _Sy_stPm

Manifold Vacuum

Carburetor Space r VRA Breather Cap Carbon Canister Ext. to Carbon Canister· Int. to Ai-1.' Clea na..r Carbon Canister Yes Yes

Sim1le One, Reverse Fl ow, Aln minized 1.nw Carbon ~t- 00 1 P. Q i:; ( ?() Q' NIA

50.8 X 1.75 (2.0 X .069)

Aluminized Low Carbon St .. ,.l 44 . S X 1.37 (1. 75 X . 054) Aluminized Low Carbon Steel

Page 7


Car Line ----'W!&tiS2.IL1AN:iiJ.lG~-----------------Model Vear 1986 Issued __ 9~/8..,5..__ Revised(•) ___ _ _ _


13.SL


TYP9 (alr inj11C11on, 9f19ine Vehicle and Engine Modifications, Exhaust Gas moditieations, olhef) Recirculation and Air I njection

Pump or pulse Pump Ormnby Serpentine Poly -V Belt

Air It.if diSlributlon JnjeelJon (head, manifold. etc.) Cyli nder Head and Catalyst Point of entry Cyl i nder Head Exhaust Ports Cata l vst Mid- Bed Type (contlQl!lld now,

Exhaust Exhaust open orifice, Olhef). Controlled Fl ow Emission Gas

Exhaust source In ternal From Exhaust X-Over (Intake Manifo l d1 Recircuta-Control lion Point ot exhaust injection (space, . carburetor ,

Snacer manifold. other)

Type TWC Toeboar d + COC Sinoli> Bri rlr l n - T.i TIP

Number ol Two Cetalytic Locatjon(s) Conver1er

Underbodv & Toeboa r d Votume [L (in1)) Toeboard - Two .62( . 38) • UndP.rbodv-One 1 . '.H78"'\ Substrate type Coated Ceramic Monolit h

Type (ventil~tes co acmospt,ere, induction $)'$tem, other) Close d I nduction Svstem

CrankcaN Emission

Ene,gy $0Ufce {manifold vacwm, carburetor, other) M:i.nifnl d V<>r .111,m

Control Oischa< (to intake rnanil~cher) Throttle Body-CF!; Carbu r etor - 2V (Canada Only) Ail inlet (breather cap, Other) Air Clea ner

Evapora- Vapor vented to I Fuel lank Externally Vented to Carbon Canister .... (crankcase, I Carburetor Internal l y Vent ed to Air Cl eaner Emission canist81 01her1 Control Vapor sec rage p,ovision Carbon Canister Electronic ~ loop (yeslnol Yes system Open loop (yesino) Yes

Engine Exhaust System

Type (single. single with ctOSS·OS81, dual, other) Sinttle Muttler no. & type ~-se flow, Slraf c thru. One, Reverse Flow, separate resonator r-.ta1erial & Mass 9 (weight lbs)! A 1 llm i n i zed l.nw r:arbon C::f' PP 1 F. Hl. 1 r,, •.n Aesona10r no. & type

Branch o.d., wall lhicl<ness Exhaust

Main cul , wa~ fliclmess pipe

Male,iaJ & Mau (kg (weight lt>S)I

Inter- o.d. & wall lhiclcness i:;(l s;i Y 1 . 7i:; (? (l(l Y n~a, mediale

Al urni nized Low Carbon Stee l ....... Material & Maas (kg {weigtl1 lbs)]

Tlil o.d. & wall thickness 50 , 8 X 1.75 (2.00 X .0691 pipe Material & Ma$5 (kg (weighl lbs)) Aluminized Low Carbon Steel

MVMA-C-86 Page 7 A


Car Line _-'!MUUL1.Sz...TuAN~G1,1_ ___ ______________ _ Model Year_.l.,.9._.8..,6..._ __ Issued __ 9.u....l><-85.,__ Revised (• l _____ _


!nillne DeacriptlontC1rti. Engine Code


Type (air in~ion. engine modi1icatlon$, other)

Pump o, pulse

Driven by Air Air distribution Injection (head, manif old, etc.)

Point of entry

Type (control led flow,

Exhaust Exheust open orifice. other)

Emission Gas E,rt,aust source

Control Recircula• lion POH1t of exhaust inject ion

(space r, carburetor, manifo ld, other )

Type

Number of

Catalytic Converter

Location(s)

Volume [L (in3)J

Substrate type

Type {venttlates to atmosphere , induction system, other)

Crankcase Emission

Energy source (manifold vacuum, carburetor , other)

Control Oisct1ar3es (to intake manilo , other)

Air inlet (breather cap, other)

Evapora· Vapor vented to I Fuel tanl< ~ve (crankcase , I Carburetor Emission canister otherl Control Vapo,-storage provision

Electron ic Closed IOop (yes/no)

system Open loop (yesmo)

Engine - Exhaust System

Type (single, single with cross-ove r. dual, other)

Mutfler no. & ty?e (rever$8 llow. straiQht ttiru. separate resonator) Matc,rial & Mass [kg (weigh! lbs)l

Resonator no. & type

Exhaust pipe

Inter· mediate

Tail pipe

MVMA-C-86

Branch o.d .. wall thickness

Main o.d .. wa ll ttiiclmess

Material & Mass {kg (weighl lbs)]

o.d. & wall thickness

Material & Mass (kg (weighl lbs))

o.d. & wall thickness

Mater ial & Mass (kg (weight lbs)J

S.OL

Vehicle and Engine Modifications, Exhaust Gas Recirculation and Air In iection Pump Belt Cylinder Head and Catalvst Cvlin der Head Exhaust Ports. Catalyst Mig-B~g

Elec t ronie Int<>lr,;> M<1.ni fold r,-nces-OVP.'I"

IntakP Port TW1. + mr n1,<!.l R,..; ,.1, Tn-T.inP

One

Underbodv 1.3 (78) + 1. 3 (78 ) Coated Ceramic Monolith

Closed Induction Svstem

Intake Manifold Vacuum

Intake Manifold Air Cleaner C,..,..;..,m Canj ster NIA r.,:i..-hnn r.::in; <;tP'I"

YPc:

Yes

Dual with Reverse "Y"

Reverse Flow

Page 7 B

car Line MUSTANG MVMA Specifications Form Passenger Car

Model Year_1_9_8_6 ___ Issued __ 9~/_8_5 __ Revised (•J _____ _


Engine De•crtptlon lCarb. l!ngin• Code

Transmisslons/Transaxle

Manual 3-speed (std., opt .. n.a .) (mfr.;

Manual 4-speed (std .. opt ., n .a.) (mfr.)

Manual 5-speed (std .. opt ., n.a.) (mfr.)

Manual o'vetdrive ($Id .. opt .• n.a.) (mt,.)

Automatic (std .• opt.. n .a.) (mfr.)

Automatic overdrive (std .. opt .. n.a .) (mfr.)

Manual TransmlsslonfTransaxle

Number of forward speeds

In first

In second

In thi•d

Transmis- In fourth

sion ratios In filth

In overdrive

In reverse

Synchronous meshing (specify gears)

Shif1 lever location

Capacity (L (Pl.fl

Type recommended Lubricant Summer

SAE vis· cosily Win ier number

Extreme cold

Clutch (Manual Transmission)

2 . 3L 3,8[,

N,A. Standard Fo

(a) (NOT AVAILABLE)

Four 3,98 :1 2,14:1 1.4 2:1 1 00 • 1

----':. QQ • 1

l c::t- 7nn ~,.,t ilt-h

Plnn,-1 , r? sn t:C::D-M?( ' SI~-''

c:,u:_S! tl W

C'~ l:::_Qnt ~

--NOT AVAILABLE

Make, type, engagement (descr ibe) -{hydraulic. cable. rod) Ford, Single Disc, Dry Plate, Cable with . Self-Ad"ustment Assisi (yes. no I percen t)

Type pressure plate springs

Total Sl)(ing load IN (lb.)!

No . ot clutch driven d iscs

Clutch lacing

Aelease bearing

Material

Manufacturer

Par1 numbe r

Aivets •plare

Aivet size

Outside & inside dia .

Total elf. area {cm'(in .1)1 Thickness

Engagement cushion method

Type & method of lubrication

No Belleville S rin 4413 992

Torbend Disc Self-Centering, Angular Contact Constant RWlnin

Torsional Method : springs. damping friction material Steel Coil Friction

(a) Axle Ratio 3.08:1 and 3,45:1

MVMA-C-86 Page 8

MVMA Specificat ions Form Passenger Car

Car Line MUSTANG Model Year...;1;;.;9;...8;....6;....._ _ _ Issued __ 9.:../_8_5 __ Revised(•) __ ___ _

METRIC (U.S. Customary )

l:ngln• Deac:rl ptlon lC•rb. Eng ine Code

Tran smlsslons/Transaxle

Manual 3-speed (slcl.. opt. , ru .j (mfr.)

Manual 4-speed (std ., opt , n.a.) (mfr.)

Manual 5-speed (std .. opt ., n.a.) (mfr.)

Manual overdr ive (std .• opt .. n.a.1 (mfr.)

Automatic (std .• opt.. n.a.) (mfr.)

Automatic 011erdrive (std .. opt., n.a.) (mfr .)

Manual TransmlsslonlTransax le

Number of lorwatd speeds

In fifSI

In second

In third

Transmis- In lour1h

sion ratios In fifth

In overdrive

In reverse

Synchronous meshing (specify gears)

Shift lever location

Capacity (L {pl .fl

Type recommended Lubr ican1 Summer

SAE vis-cosily Winie r number

Extreme cold

Clutch ( Manual Transmission )

Make. t~pe. engagement (describe) -jhydtau ic. cable. tod )

AsSist (yes . no I percent)

Type pressure p/ale springs

TOID.I spring load [N (lb.JI

No. of clutch driven discs

Material

Manulactute r

Part numbe<

Rivet:.·plate

Clulch Rivel Size lacing

Outside & inSide dia.

Total eft. atea (cm2(,r,.')J

Thickness

Engagement cushion melhod

Release Trpe & method bearing o lubrication

To rsional Metnod: Sptings, damp ing friction mater ial

5.0L

( a)

Five 3. 35:1 1.91: 1 1. 29 ~ 1 1.nn - 1 () i:.12 • 1

lrl, r.0<11-r 'l: 1C:• 1

An Fn ...... "'T'rl r. .. <11-rc

I: 1 nn-r

? " rr::. "' n----- TT

------

Si ngle Disc, Dry Pl ate, Cable with Self-A djustment No Bellevil l e Spring 7402 (1664) One Woven Non-Asbestos, Val eo F-202 Valeo E6ZR-7550-AA 18 4 . 1 X 5 . 4 (5/32 X 7 /32) 268 X 170 ( 10.55 X 6.69) 674 (104 . 5) 3.6 ( .142)

Torbend Disc Self Centering, Angular Contact, rnn ~t-11nt ~ a . P-renacked

St-oo l ro ; 1 Sn-ri na~/0-rv i:;..,.; ,-+; r.n

(a) Axle Ratio 2.73:1 and 3.08:1 Locker

MVMA•C-86 Page 8 A


Car line _MU_S_T_AN_G ______ ___,. ___________ _ Mode l Year __ 19_8_6 ___ Issued __ 9"""/_8_5 __ Revlsecl (•) _____ _


Automatic Transmlsalon/Transaxle

Trade name

Type and special features (describe)

Selector

Gear ratios

Locat ion

Ltr ./No. designation

R

0

L,

Max. upshilt speed• drive range (km/h (mph))

Max. kickdown speed• drive range (km/h (mph))

Min . overdrive speed (km/h (mph )!

Torque convener

Lubricant

Number of elements

Max. ratio at stall

Type of cooling (air, liquid)

Nominal diameter

Capacity [refill l (pt)]

Type Recommended

Oil cooler (std., opt., NA, intemal, external, air, liquid)

Axle or Front Wheel Drive Unit

Type (Iron!, rear)

Description

Limited slip (f1fferential {type)

Drive pin ion offset

Drive pinion (type)

No. of clifterential pinions

Pinion / differential adjustment (shim , other)

Pinion/ differential bearing adj ustment (shim. othe r

Driving whee l bearing (type)

Lubricant

Capacity (L (pt.lJ

Type recommended

SAE vis• cosity number

Summer

Winier

Extremecoki

2.3L

Sel ectShift C-Torque Converter, Planetar Gear S Floor PRND21 2 11: 1

. 1

Rear

SAE-85W90

3.8L

Locking Torque Converter,

a heat

e with Cast Cent er and Overhun Pinion

Axle orTransaxle Ratio and Tooth Combinations 1see·PowerTeams·1or axle ratio usage .)

Axle ratio (or overall top gear ratio)

No. ot leelh

Ring gear o .d .

Transaxle

MVMA•C-86

Pinion

Ring gear Of gear

Transfer gear rat io

Final drive ratio

15 11 11 1 8

Page 9


Car Line _ _,MU"""""S,...T .... AN_G ______ ______ ______ _

Model Year_l_9_8_6 __ _ Issued _....:9::../c...;8::.,5"--_ Revised (• ) _____ _


3.81 S.OL

Automatic Transmission/Trans.axle

Trade name Automatic Overdrive (AOD1 Type and special feaMes (desQibe)

Torque Converter . Planetarv Gear Set Selector Location Floor

Ltr ./No. designation P RN D D 1 R 2 . 00

Gear D 0.67 ratios L3 1.00

L, 1,47 L, 2 40

Max. upshlfl speed• drive range lkmlh (mph)) 102.3(6'.L61 (a) q 7( F-n _ ·n (h l lB E:;(70 i:;) (c- l Max. l<ickdown speed. drive range [km/h (mph)) R6 i:;(c:'t _ 71 Sl.?(C:O O'\ 07 '{(F,/) C:'\

Min. overdrive speltd lkmlh (mph)I 68. 5( 42 .6) 65(40,4) 69.3(43) Number ot elements Three

Torque Max. rat io at staU 2.53:1 conver1&r Type of oooling (air. liquid! Liauid Passes throuo-h a Heat Ex..-hano-e-r in R,:i,li atn -r

Nominal diameter 305 (12) Lubricant Capacity [refill L (pt .)) 11. 7 (24 . 6)

Type Recommended ESP-M2Cl66-H Oil cooler (std., opt., NA, interna l, external, air, liquid ) Standard. External Oi l t-n Fnoi.ne f:nnl;int

Axle or Front Wheel Drive Unit

Type lfr011t, rear) Rear Description Semi- Floating Type with Cast Center and Overhung Pinion Limited slip differential (type) t-rict1on Plate Drive pinion offso t 38. l(l.5) 25.4( 1.0) Drive pinion (type) HypOl.d

No. ol differential pinions Two Pinion/ differential adjustment (shim, o~) Shim Pif'lion / differential bearing adjustment (shim , other Co11aps1b l e Spacer, Shim Driving Wheel bearing (type) Stra i ght Roller

Capacity IL (pt.)J 1. 78(3. 75) 1.5(3.25) Type recommended ESP-M2C154-A

Lubricant SAE vis- Summer SAE 85W90 cosily Winter SAE 85W90 number

SAE 8SW90 Extreme cotd

Axle or Transaxle Ratio and Tooth Combinations (See ·power Teams· tor aide ratio usage.I

Axle ratio (or overall top gear ratio)

I Pinion No. ot teeth I Ring gear or gear

Ring gear o.d .

Transax le I Transler gear ratio

I Final drive ratio

(a) With 3.8L Eng, (b) With 3.8L Eng. (c) With 5.0L Eng.

MVMA-C·86

and and

3.27:l(a) 11 36 190.5 (7 .S ) N/A N/A

3.45: l(b) 11 38

3 . 27 :1 Ratio Rear Axle 3.45:1 Ratio Rear Axle

Page9 A

2.73:l(c) 3.08:Hc) 3 . 27:Hc) 15 13 11 31 40 36 221(8.7) 223.5(8.8)


car Line MUSTANG Model Vear 1986 Issued __ 9....;..../_S_S __ Revised( • ) ____ _


Engine Deacrtpllon/Carl> . Engine Code

Propelle r Shaft - Rear Wheel Drive

Type (straig ht tube, tub&-ln-tube, internal-external dampe,, etc,)

Manual 3-speecl trans.

Manual 4-speed trans.

Outer (M4W4) diam, X ~--wal Manual 5-speed trans, thick-nellS

Ove<oriva (AOD) ( 4-Speed Auto.)

Automatic t<ansmission

(3- Speed)

Int er-Type (plain. anti -friction)

mediate bearing

Lubrication (fitting. prepack)

Type

Slip yoke Number of teoch

Splineo.d.

Make and mfg . no. ! Front

j Rear

Numbef Used

Type (ball and trunnion, cross)

Universal joints Rear attach (u-bolt. clamp, etc .)

Type (plain,

Bearing anti-friction)

Lubrication (fitting. prepack}

Drive taken through (to,que tube , arms or springs)

TOtQue taken through (torque tube. arms or springs)

2.3L

Internal Tuned Damt)er

N/A

76.2 X 1186 .1 X 1.65 (3.00 X 46 ,7 0 X . 065)

N/A

N/A (C- 3) 76 , 2 X 1216.7 X 1.6 5 (3,00 X 47.90 X . 065)

NIA

NIA Plain w/3 -Speed Auto; Tuned DamnPr w/4-SnP erl Man.

25

28.32 (1.12) Ford 1310 Ford 1310 Two

Cross 12 mm Bolts

Needle Roll er

Pren.,.,-\

Control Arms

Control Arms

• Centerline to centerline of universal joints, or to centel1ine of rear attachment .

MVMA-C-86

Page lO (Rear Whee l Drive)

3.8L

Straight Tube with Internal Tuned Damoer

N/A

69.85 X 1196.3 X 1.65) (2.75 X 47,l X .065) (C-5) 69 . 85 X 1181.1 X 1. 65 (2.75 X 46.50 X .065)

Plain w/3-Speed Auto; Tuned O~mper w/4 - Spd . ~uto CAOD)

28

30.99 ( 1. 22) Max


car Line MUSTANG MOdel Year 1986 Issued _ _..9.._/_..8..._5 __ Revised( • ) _ _ __ _


ll!nfllM n..crt ptlon!Can,. Engine Code

P II r Shatt Rear Whe el Drive rope e -Type (Slralghl tube. tube-in -tube, intemal .. xtema l damper, etc.)

Manual 3-speed trans .

Manual 4-speed trans.

Outer diam x 18:rh' X wal Manual 5-speed trans . thick-ness

Overdrive

(AOD) Automatic transmission

(4- Spd Overdrive)

Inter -Type (plain, anti-friction)

mediate bearing

LubricaliOn (fitting, prepack )

Type

Slip y<>ka Number of teeth

Spline o .d.

Make and mfg. no. I Front

I Rear

Number\lsed

Type (bal l and trunnioo, cross)

Universal joints Rear attach (\l·boll, clamp , etc .)

Bearing

Type (pla in. anti •lriction)

Lubrica1ion (lilt ing, prepack)

Drive taken lhrough (torque l\lbe , arms or springs)

Torque taken through (torque tube , arms or springs)

S.0L

Internal TWled Damner

N/A

N/A

76.2 X 1150,6 X 1.65) (3 . 00 X 45,30 X . 065)

N/A

76. 2 X 1162,1 X 1. 65 (3,00 X 45,75 X . 065)

N/A

NIA Plain-w/5-Speed Manual TunPn n:lmnP-r-w/Ann A, 1f-nm~ f' ir

28

30.988 (1.22) Max. Ford 1310 Ford 1310 Two

Cross 12 rn. 4 7) Bal ts

Needle Roller

Preoack

Control Arms

Control Arms

• Cent8f1ine to cente~ine ol univel'Slll joints, or to centerline of rear attachment.

MVMA•C-86 Page 10 A

(Rear Whee l Drive)


Car line __ MU'"'="S ... T...--AN_G _________________ _

Model Year_ 1_9_8_6 ___ Issued _ .... 9~1 ..... Bc...S'--- Revised(•) _____ _


Body Typtt And/Or Englr» Dlaplac:ement

Suspension - General

Car Sld.,Opt.ln.a .

leveling Type (air, hyd., etc.)

Manual/auto. controlled

Provision fo r brake dip control

Pr011ision !or accl. sqL>at control

Provisions for car jacking

Type

ShOck absorber Make (!ront & rear) Piston diame1er

Rod diameter

Suspension - Front

Type and desctlplion

Ofive and torque taken lhrough

Travel

$pting

Stat>i~zer

Full jounce

Full rebound

Type (coil . leaf, other) & mater ial

Insulators (type & mater ial!

Size (coil design height & i.d .. bar length x dia.)

Spring rate (N1mm (lb .1in.))

Raia at wheel [Nlmm (lb.ltn.))

Type (link , linkless . frameless}

Material & bar diameter

Suspension - Rear

Type and description

Drive e.nd torque laken through

Travel Full jounce

Full rebound

Type (coil , leaf, other) & material

Size (len9th x width, coil c)esign height & 1.d .. bar length & dia.l

Spring Spring rate tN1mm (lb.'i ••-H

Rate at wheel [Nlmm (lb /111.))

Insulators (type & material!

II ] No . ol leaves

leaf I St,ackle (comp. or tens .}

Stabilizer Type (Unk. linkless. framelessl

Mate rial & bar diameter

Track bar (type)

MVMA-C-06

ALL MODELS WITHOUT QUADRA SHOCK REAR SUSPENSION

N/A N/A N/A Front Spri n~s Motmted on Lower Control Arms Unequal Len2th Upper/Lower Control Arms (Rear Susoension)

Side of Car - Outside Rocker Panel Flan~es. Front & Rear Direct Doubl e Acting Hydraulic Front Strut s and Rear Shocks Motorcraft Front 34.8 ( 1.37); Rear 25.4 (1.0) Front 22 (0.87): Rear 12 . S (0.50)

on Lower

254 x 89.0 (10.0 x 3.50) (Coil) 2962 (116 . 6) (Bar Length); 15. 6 (0.61) (Bar Dia.)

Base 65 .0 (370 28.00 (159.6)

Link· Rubber Side Rail Insulator SAE 1090 · Base 23.9 0.94 · 28.S 1.12

Four Bar Link with Coil Sorin2 on Lower Arm Unner & Lower Contro l Arms 74.04 (2 .91) 126.1 (4.96) Coil- SAE 5160-H Steel

220. 7 X 102 (8 . 69 X 4.02) (Coil), 2732 (107 .6) (Bar Length) 13.0 (0.51) (Bar ·Dia.) 28 (lf.O) 16. 8 (96) D11hhP.r

NIA NIA NIA N/A None

Page 11


Car Line _....;.;MU=S~T.:..:AN=G;_ ______________ ,....... __ Mode l Year_1 ___ 9 ___ 8""'6"'---- Issued __ 9_/_8_5 __ Revised(•) _ ___ _

METRIC (U.S. Customary )

Body Type And/Or Engine 01apl•c:ement

Suspension - General

Car leveling

Stc!.,opt.in.a.

Type (air. hyd. , etc .)

Manual/auto. conttolled

Provision lor brake d ip control

Prov ision lo, accl. squat control

Provisions lo, car jaclting

Shock absortJer (front& rear)

Type

Piston diameter

Rod diameter

Suspension - Front

Type and descripbon

Drive and torque lalcen through

Travel Fua jounce

Fun rebound

Type (coil . leaf, other) & malarial

Insulators (lype & material)

Spring Size (coil design height & i.d ., bar length X dia.)

Spr ing rate (Ntmm (lb.iin.)I

Rate al Wheel (N1mm (lb.lin .)J

Stabilizer Type (lil'lk. linldess, frameless)

Material & bar diame1er

Suspension - Rear

Type and d&scriplioo

Drive and torque taken thlough

Travel Full jounce

Full rebound

Type (coil. leaf. olher) & matefial

Size (le"lllh x width , co~ des3n heignt & ,.d ., bar length & dia.

Spring Spring rate (N,mm (lb .fin .JI

Rale al whee l (Nlmm (lb .1in.)J

lnsulalo,s (type & material)

If I No. of leaves leaf I Shack le (oomp. or tens .)

Slabilizer Type (link, hnkle55. trameless)

Material & bat diamet8f'

Track bar (fype)

MVMA·C·86

(HANDLING SUSPENSION) ALL MODELS Wini QUAORA SHOCK REAR SUSPNES!ON (STil. W/GT)

N/A

Arms Rear

Direct Double Acting Nitrogen Gas-Pressurized Hyd. Frt. Struts & Rear Vert . Shocks Freon Ba H d . Horiz Axl Motorcraft Front 34,8 1. 37 · Rear 25 4 Front 22 0 , 87 · Rear 12 5 0

Hybrid MacPherson Strut w/Springs Mounted on Lower Control Arms Cont rol Arms, Bushings and Strut Mts. 91.00 ( 3 .58) 86.86 (3 . 42) Coil, SAE 5160 Stee l Uooer - Ri n'1. Lower - Sleeve & Rubber Variable Rate: 245.2 X 89.0 (9.65 X 3.50) Coil 2987 (116 . 6) Bar r..,.noth• H, .4 ro . 1,,..1.~1 Bar n i <1m.<:!t'.,..,.

H. D. Handl inP 75 . 0 (.1? C:'\

26.S f1r;11

Link; Rubber Side Rai l In sulator SAE 1090 Stee l & 33.0 (1 . 30)

Four Bar Link with Coil Spri ng on Lower Arm Upper & Lower Contro l Arms 82.60 (3.25). 117 .60 ( 4. 63) Coil. SAE 5160 - H Steel Variable Rate : 102 X 220.7 (8.69 X 4.02) (Coil),2474(97.4)(Bar Length) 14.2(0 . 56) (Bar Dia.) 35 (200) 16.9 (95.4) Rubber N/A N/A Link l ess (NIA Stan dard Dutv Susoe nsion) SAE 1090 Steel & 20 fO. 79) and 21 (0 . 83) -None

Paget1A


Car Line ---=-MU=S:....:T:..:.AN.::.a.aG,.__ ________________ _

Model Year_l=-9~8-=6 ___ Issued _,..9,.,./..,8.,.5,__ __ Revised(•) _____ _


Body TYJM And /Or ~Dlapl~

Brakes • Service

IALL MODELS

Description Four Wheel H draulic Actuated S s tem

Brake type (std .. opt., ru .)

Froot (disc 0t drum )

Rear { disc Ot drum)

Sen-adjusting (std .• opt , n.a .)

Special ValVing Ty pe (proportion, delay, metering, other)

Disc Drum Standard

Pressure Power brake (std .• opt .. n.a.) Standard _Boo_st_e_rty~pe:;.;...:(~remo_ t_e,~in~t~:.:..:.•a~t._vac,;.....:·•-h~yd~ .. _e~tc~.) __ __ +2~0=0~8~•~6~6~~S~1~·na.:..o,~l~e--"D~i~:.!.Lit.-"--lr.,!l!.....ll.,I.JW, ....... <.1.L..lo£1......,,__=-.......,.....,_'-o,.lu;o,.~L<a,; ...... ......,~a) Vacuum s<Mce (inline, pump, etc.) N • A• Vacuum resen,oir (volume in.3) N A

Vacuum pump-type (alee, gear driven. belt driven, II other so state )

Anti-skid deYiCe type (std .. opt ., n.a .. ) (FIR)

Effective area (cm2(in.2>r ( F / R Gross l ining area (cm2 (in.2)J"' (FIR)

Swept area (cm2 (in.2)) .. '(FIR)

Outerwortting diamerer

Rotor Inner working diameter

Thickness

Material & type (vented/solid)

Otum Diameter & width

Type and material

Wheel cylinder bore

Master cylinde r Bore/stroke

Pedal arc raoo Line pressure at 445 N(100 lb.) peoal load (kPa (psi)(

FIR

F/R

FIR

FIA

FIR

FIR

FIR

Lining clearance FIR

Brake Mning

8onCled or riveled (rivetsiseg.)

Rivet size

Manufacturer

Front lining coe1e••u•

wheel Material

Primary or out•bOard

Sil& Secondary o, in-board

Shoe thickness (no lining)

Bonded 01 riveted (riv•ts!seg.)

Rear Manutac1urer wheel Uning CocSe•·•· · ·

Mate,-iat

Prima ry o, out-boar d

Size Secondary 0t fn-board

Shoe thickness (ne> lining)

•Excludes rivet hole1.grooves. chamfers. etc . .. Includes rivet holes , grooves, chamfers, etc .

... TO!al swept area for four brakes. (Drum brake: Widest tining contact width lor each brake x its contact circumference .) (Disc brake: Square ol Oucer Working Dia.minus Square of inner Woc1ting Dia. multiplied by p; ,2 tor each brake.)

••••size lof drum brakes includes length x width x thickness . ..... Manufec:turer 1.0., cat alog or formulation designation and coetticient of friction Classification.

(a) 152.4 (6.0) Tandem Dia phragm w/all Engines (except 2.3L)

MVMA ·C-86 Page 12


Car Line MUSTANG Model Year 1986 Issued __ 9._./__.8_5 __ Revised(•) _____ _


BodyTwi-And/Or Engine Dlap-=-nt

Tires And Wheels (Standard)

Size (load range, ply)

Type (bias. radial. etc.I

Inflation pres- Front lkPa {psi)) Tires aure (cold) tor

recommended maJ<,vehk:le Rear (kPa (psi)) load

RevJrnile--at 70 kmiti { 45 mph)

Type & material

Rim (size & lfar,ge type)

Wheels Wheel offset

Type (bolt or stud)

Attachment Circle diame1e,

Number & size

Tire and wheel (same, i1

Spare other descra)

Slorag1t poSilion & location (describe)

Tires And Wheels (Optional)

Size (load range. ply)

Type (bias, radial, etc.)

Wl1eel (type & material)

Rim (si2e, flange type and offset)

~ (IOad 1arige, ply)

Type (bias, radial, etc .)

Wheel (type & material)

Rim (size. flange type and offset)


Type (bias, radial, etc.)

Wheel (type & material)

Rim (size, flange type and offset )

Size Qoad range. p(yl

Type (bias, ~I. etc .)

W1wel (type & material I

Rim (size, flange type and offset)

Spare tire and wheel

(if configuration is dilterent than road lite °' wheel , describe o;>llonal spare tire and/or wheel locallon & stora~ positiO<i

Brakes - Parking

Type of control

Locetion ot control

Operates on

Type (inte,nal or el(ternal)

llsepa,lle lrooiservice

Orum diameier

brakff u,,1r,g size (length J width x lhickneaa)

MVMA·C·86

LX MODELS ONLY (w/2.3L or 3.8L ENG. ONLY)

(See Page 13A f or GT Mode 1 or Mo els w Opt. S. d I OLE ng1ne ) Pl95/7SR14 Steel Belted Radial

207 ( 30)

207 (30) 1295.S (805) Stamned Steel (14 X S) JJ 28.45 (1.12) Stud (4.,c;)

Fa ,,..,. - 1 ?. 7 r . sm - 20 Thd B78-14, kPa (36 psi), Steel Wheel 356xl27 ( 14.xS. 0), F.conomv C:nar<>

Fl"t- Posit:inn Deen Well in Tr11nle

P201:;/70R1A

St-<><>1 n .... 1,-,,..-½ 11,:arli"l

Pnl Vl""'~'t /C:..'tAP 1 (C:..'tvl 1>rl lln::ir{)

{ 1 ,1 y c; I:;) T 1 nf'f'c:.,,..,. ?R .:1.c; r1 1?1

Tire Matching Other Four Tires with 14 X 5.5 Steel Wheel (Conventional Spare) Mini-Spare w/Aluminum Wheel 15"x411 on Select Models

Pull Lever - Push Button Release Tunnel Mounted Rear Service Brakes NIA NIA

N/A

Page 13


car Line MUST ANG Model Yaar....aa;19_8;;;..;6:;...._. __ lssued __ ,2~/.,.8""5 __ Revised (•) _ _ __ _


Body Type And/Or bgJne Dlapl1~

Tires And Wheels (Standard)

SiZe (loed range, ply)

Type (bias, raiial, etc.)

Tires Inflation pressure (eoldl !or recommended max.~ load

Front [kPa (psi)l

Re¥ (kPa (psi))

RevJmile-at 70 km/h (45 mph)

Type & malefial

Rim (size & flange type )

Wheels WhNloffsel

Type (bolt« stud)

AttachtMnl Circle diameter

Number & size

Spare

Twe and wheel (s,me, it other describe)

SIOl'IIQ9 pOsilion & location (deacribe)

Tires And Whee ls (Optional)

Size (1oaO range , ply)

Type (bias. radial, etc.)

Wheel (type & ma1erial)

Rim (size, flange 1ype and ollsel)



Wheel (type & ma1erial)

Rim (size. flange type and ottse1)


Ty pe (bias, r~. elC:.)

Wheel (type & materiel)

Rim (size, flange type and offset)

Size (load ,ange , ply)


Wheel (type & ma1erlel)

Aim ($iza. flange typO and otl$ft)

Spare tire and wheel

Qf ~uretion is diNerent ll'lan road tire Of Mieel , describe optlonel spare th and/Of wheal location & storage position

Brak rid ea- Pa ng

Type of control

Loc:a~on of control

Operates on

Type (Internal or external)

H separale Drum diamete, from servtoe brakes Linint size (lllflVlh ~

widtll • lhicknets)

GT MODEL OR MODELS WITH OPTIONAL S.OL ENGINE

2

207 30

Al uminum Ten Hole St le 1S X 7 22 4 0.88 Stud

2

B78-14, 250 kPa (36 PSI), Steel Wheel 356 x 127 (14x5 . 0), E

F

(NOT AVAILABLE)

/ A '1..\.,.-

- -o..e ,. ,,._<:, \

,t,_?,. ~IC,

/~-

MVMA·C·86 Page 13 A


Carline -- ... MU....,,.S,.,.T_AN_G ________________ _

Model Year _ _ l_9_B_6 __ Issued _ _ 9+-/.,.8_.5 __ Revised(•) ------

METR IC (U.S. Customary)

9octrT'V.-AndfOI> lnglne Dtspl,c,n,ent

Steering

M.,1u, 1 (std ., opt. . n.a.)

Power(Sld .. opt. , n.a.)

Adjustable TWIMland dnctlpljon ste."whttl (Ult,~. O!Mr) (Sid ., ope,. n,a.)

Wheel diameter Manu,1 (W9)SAEJ1100

Pow.I'

Outside Wall to wall (I. & r .)

Turning front Curb to eurb (I, & r.) dllll!leler

Walltowall(I. &r.) m(ft.) Inside rear Curbtocurb{I. & r .)

Scrub Radius'

Type

Gear Make

Manual l o.ar Ratios I 0v"a1

No. wheel turns jstop to stop)

Type (ooa,cial, l inkage, etc .)

Make

Type Power l• Gaar Ratios I Overall

Pump(onve)

No. wtleel tums (stop to stop)

Type

Linkage Location (front or rear of whee ls, olh11r)

Tie rods (one or two)

Incl ination at camber (de9.)

Ste.ing Upper Aldi Bearings Lower (type)

Thrust Steering spindle & joint type

Oiamet er Inner bearing

Wheel 0ut9f bearing spindle

Thread (size)

Bearing (typa)

ALL MODELS

N.A. Sta ndard

Tilt s Pncdtion Ont-iO"'"'l N . A Srri. 168 (14.S)

11 1Q (17 'lf.): Exe. 11.89 (39.0) wLGT

N.A. ----

--InteQral Rack a nd Pinion Gear - (Ford). Pumn - (Fnrd): Flu i d F.SP-M2CD8-r T Rack and Pinion (Variab 1° ~atio) (a)

8.'i8°/mm nn ront-or• 7.91°/mm at- s,-nns (a)

20 nn • I nn C~nt-,:,r • 15.Q7•1 at- St-"''"'!'l. fa) B<>l.t Off r.r,in ln:haft- p .. 11,,v 1 n, {,.) ~""Ir anrl Pi_nfnn (~nrl 1,, Ra 11 T~~.-,t- TH T <>"t- At-t-<>rh

Front of Wheels

Two (Inte2ral with Gear) 15. 7 Strut Mount Bal l Joint

ForQed Suin dl e . wit-h Ral l .Jn-1 nt-

14. R ( 1. 37) ?1 . .R to 86) 11/16 - 20 UNF.F ?t. RU "'""""'"',I Tapered Roller

'Toe horiZon1al distam;eio !he front elevation~ wt1Nlcentar11ne and kir19pin (bal l jolrU)&xis at ground.

(a) Handling Suspension: Std. w/GT Model Gear Type - Constant Ratio Rack Speed - 6.44°/mm Overall Ratio - 15.01:1 On Center, 13.00:1 at Stops No. Wheel Turns - 2.46 (Stop to Stop)

* Rack Speed

MVMA-C·86 Page14

t-n (!,.,,., .,. )


Car Line __ MU_S_T~AN __ G ______________ _ __ _

Model Year 1986 Issued _ __,,9CL/..,.8""5_ Revised(•) ____ _


Body Type And/Or Engine °'9pllleem ent

Wheel Alignment

SeNioe caster (deg .) checking Camber (deg .)

Toe411 (outside track-mm (in.)J

From Service Caster

wheel at reset' Camber curb mass (wt.) Toe-in

Periodic Caster M.V. In- Camber spec:tion

Toe-in

Service Camber (deg.)

Rear checking Toe-in (ou1side track-mm (in .)]

Wheelal Service Cambel

curt>mass (wt,) reset' Toe-in

en Camber M.V . in-spection Toe-in

• ln<licales pre-set, adjustable. trend set or other .

Electrica l - Instruments and Equipmen t

Type

Trip odometer (std .. opt.. n .a.)

EGA mainlenance indicato,

~ Type

Wamingdellice

Temperature Type

indicator Warning device

Oil pressure Type

indicator Warning device

Fuel Type

indicator Warning dlwice

Type (standard)

Wind• Type (oplion atl st,ield Wipel Bla<la length

Swept area (cm2(in.')f

Wind- Type (standard)

shield Type (optional) washer

Fluid level indleator

Hom Type

Number used

Other See Page lSA

I ALL MODELS

Pointer Standard

None Warnin Air Electric Two Std On

(a) (b)

Max Side to Side Difference Not to Exceed+ 0.75 Electronic Graphic Display Indicator SystePi' in Console. Indicator for Headlamps, Tailla.mps or Brake Lights, and (Opt. w/2-Dr . Sedan)

MVMA·C-86 Page 15

b

Also includes Lamp-Out Low Fuel Warning Light.

MVMA Specifications Form Passenger Car METRIC (U.S. Customary) SUPPLEMENTAL PAGE

caru~-- ..... MU~S~T_AN_G,;_ ______________ _

Model Year I9a6 lsl,i,ed --9 .... t .... B-S-- ReYlaed0

(•> ____ _

Electrical - Instruments and Equipment: (Cont'd.)

• Brake System Warning Light

, Emergency Flashers

• Directional Turn Signal Lights

• Hi-Beam Indicator Light

• Fasten Seat Belts Warning Light

• Headlamps "ON" Warning Buzzer

• Up-shift Indicator Light (Not available Canada)

Page 15A


Car Line __ MU_S_T_AN_G _ ____ __ __ __ _____ _

Model Year 1986 Issued _ ... 9 .. f..,8,..5 __ Revised(•)-----


El rilS ISt •ct ca - upp1y ys em

Malcl

Model, std., (opt .)

Voltage

Batte,y Amps 11 O"F COid crank

MinutN-reserve capacity

Amp/hrs . • 20 Iv. rate

Location

Generator Type and rating

Of Ratio (alt. crank/rev.) alternator Optional (type & rating)

RegulalOf Type

Electrical - Starting System

Start, mocor Curren! Cltaln at O'F

Engagement type Motor

Pinion engages drive from (1l'ont. rearl

Electrical - Ignition System

Type ElecttoNc (std., opt., n,11,)

Other (specify)

Make

Coil Model

Currllnl I Engine stopped - A

I Engine ~ing -A

Male• Model

~ Thtead(mm)

Tightening torque (N-m (lb. tt)J Gap

Number per cylinder

Distributor Mak•

Model

Electrtcal - Suppression

Location• & type

2,3L 3,8L

Motorcraft St anda rd 12 310; 380 (a); 450 (b) 380 : 450 (b) 60: 75 (a): 90 (b) 75 : 90 (b)

36 : 45 (a): 54 (b) 45 : 54 (b)

Ri2ht Hand Front of En2ine Comoartment ElZF-DA (40 AmD) ESSF-AA (60 AmD)

2.31:1 (2.42:l w/A/C) 3 'V, • l

ElZF- BA (60 Amo) (c) N A

Electronic

260- 285 Amns ?7'- - 1.00 A-"'"' Positiv~

Front

Standard N.A. Motorcr.afr-E1.F'.F-AA P.".l.J;>J.'_AA {r.FT) 0 n,Al<'-ARI?

6.5 'i 0 Motorcraft AWSF--4C AWSF-54C 14 7.0-14 . 0 (5-10) 7 .0-15 .0 (5-11) 1. 12 (0 . 044) 1. 3-1.4 ( .O'i?-.O'ifi)

One Mo tore raft Universal (Canada - Dura Soark I I) (d)

Capacitor in Alternator, Resistor Spark Plugs and Resistance Core Ignition Wire. Ground Cable - Engine to Dash Ground Cable, Hood Bond, RF Shielding Material . Ground Strap - Premium Sound Amp to Radio,

(a) Included with Auto. Trans . (b) Optional Heavy Duty Battery; Standard with Convertible. (c) ElZF-BA with A/C (d) Universal w/CFI; Dura Spark II w/3.BL 2V (Canada)

MVMA·C-86 Page 16

V)


ca, Line --.a:M~US,.,T,-AN ____ G _____ _ _______ _ _ _

Mada Yw 1986 lsSued 9/85 Reviaed(•>--- --

METRIC (U.S. cu.tomary)

Electrical - Supply System

Make

Model, Sid., (opt)

Voltage

Battery Amps at O"F cold crank

Miooteweserve capacity

Amp/hrs . • 20 hr. rate

Location

Generator Type and rating

Of Ratio (ah. crank/ rev,) ...,,,alor Optional (type & rating)

Regulator Type

Electrical - Starting System

Start. motor Current draln at O"F

Engagement type Motor Pinion engages drive

from (fr0"1, rear)

Electrical - Ignition System

Type Electronic (std ., opt . n.a.)

Other (specify)

Make

Coil Model

Current I Eng ine stop ?&(l - A

I Engine idllng - A

Make

Model

Spa"- lmlad(mm) plug Tightening torque [N-m (lb, ft)I

Gap

Number per qt;nder

Distributor Make

Mode l

Electrlcal - Supp, .. 11on

Locations & type

MVMA-C-86

5 .0L (MANUAL TRANS. ) (AUTO. TRANS.)

Motor craft Standard 12 450

90 54

Left Hand Front of En2ine Comoartment E67F-DA (60 Amo) E6SF-AA (60 Amo) 2. 68 :1 3 .00: l N. A. Electr onic w/Inte2ral Re~ulator

290- 315 Amps Positive

Front

Standard N.A. Motorcraft (E) - Core 6,5 2.5 Mnt orc r aft AWSF-4 4 14 14-20.3 (10-l'-)

1 n fO . o-.rn n ... ,,. Mnt-orc-r<>f't"

Tinin=~~,,, - u~,, p;:f'ort-

Capacitor in Alternator, Resis t or Spark Plugs, Resistance Ignition Wire, Ground Cable - Engine to Dash, Hood Bond. Ground Strap - Premium Sound Amp to Radio .

Page 16A

MVMA Specificat ions Form Passen ger Car

CarUne --.;:,MU"="'=S:-':T;.;.;AN=G ________ _ _______ _

Model Year __ 19_8_6 ___ Issued __ 9.,.1_a_5 __ Reviaed (•) _____ _


Body

Struch.lre

Bumper system front-rear

Anli-c:orrosiontreatment

Body - Miscellaneou s Information

Type ot finish (lacquer . enamel, other)

Hinge location (front rear) Hood Type (counter balance , proe)

Release conlrol (intemal, external)

Trunk Type (count erbalance , other)

lid Internal release control (elec. , mech .• n .a.)

Hatch- Type (counterbalance . o:her)

back lid Internal release control (elec .. mech .. n.a.J

Vent window control (crank, Front

flicti0n. pillot, power) Rear

Seat culhlon type Front

(e.g., 60140, bucke1. bench, Rear wire. toam etc.)

3rd seat

Seatbac:l<ty: Front

(e.g., 60140, ucl<et, beneh, Rear wile. loem etc .)

3rOseat

MVMA-C-86

I ALL MODELS

Unitized All-Steel Welded Body, with One-Piece Side Stampings and Energy-Absorbing Fron t and Rear Structures

Impact-Resistant Polyuret hane Fascia and Steel - HSLA 50 Understructure. Will Withstand 5 mph Impact from 15° Pendulum on Center-Line of Car Without 'Damage

• Major Exterior & Underbody Sheet Metal Components and Panels Pre-Coated (Galvanized) Steel Body Cathodically Electrocoat Pr .imed

• Urethane Chip Resistant Primer ~r Plastic Cladding on Lower Body Sides r.ril l o• AR S Pla"' t-ir-

Enamel (Acrylic) Rear Prop Primary - Internal, Secondary - Externa l Counterbala nce (2-Door Sedan & Conve rtible) Electric (with Power Lock Group) Gas Cyl i nders Electric

None None St amped Frame - Coil Sprin2 & Fl exo l ato r - Foam Pad Integral Frame & Foam Pad Assembly None Stamped Frame - Foam Pad Frame Hard Board with Foam Pad Assemblv None

Page17

MVMA Specifications Form Passenger Car METRIC (Ul. . Customary)

Carline _..,MU,.._,S__,T,..AN_G _ ___ ~=-----------Mod&IYear_1_9_8_6 ___ 1ssuec1 _9 '-/8_5 ___ Revised(•) ____ _

ALI, MODELS

Aettralnt System

Slandard'optional Rear: Color Keyed Webbing

Ac1lve Front: Color Keyed Webbing with Tension Eliminator restraint

Type and description system Continuous Loop - Front Lap Only - Rear Location

2 Seat Belts - Front 2 - Rear Staooard/opliOnal

N/A Passive Power/manual seat N/A bells

2or3poinl

N/A I( riff baf llap belt

N/A

Frame

Type II/Id daseriplion ~rate frame. un~lzedframe , partlal -unitized frame ) Unitized Construction

Glass IAI

2-Door Sedan Convertible 2-Door Hatchback "-I.No.

Windshield glus exl)9Sed iwrlaee area (cm~(in.")]

S1 8114 (1258) 7220 (1118) 8114 (1258)

Side rclass e~ surface area em2(in. ]•tot al2•6ides

$2 8313 (1288) 7303 (1132) 8101 (1256)

Backlight glass ex~ Sllrfacearea(cm 2 in. ]

53 8583 (1330) 3723 (577) 8569 (1328) Toeal gtasse~sed surface area (cm2(in. J

S4 25009 (3876) 18239 (2827) 24784 (3841)

Windshield g1a$S (type) Laminated

Side glass {type) Tempered

Bacidight glass (type) Tempered

Page 18


Car Line _ _ MU __ ST_AN __ G __ _ _ ____ ___ _ ____ _ _

Model Year__.1~9~8~6~ -- Issued -~9...,./~B~S~- Revised( • ) _____ _


ALL MODELS

Convenience Equipment (standard, optional , n.a.)

Aif c:ondilioning (manual, 81/10. temp c:onuol) Optiona l , Manual Temperature Cont r ol Clock (digital, analogl Standard, Digital tHase) Campus t thermometer N,A. Consore (floor, ovethelld) Optional on z-ur . :sedan. :standard with Al l Otner Model Defroster, elec. bacldighl Optional (Mandatory New York State)

Oiagnostic waming (integrated. individual) Graphic Warning Disp l ay (Part of Console) Instrument ~st« (l iS1 instruments) N. A. Keyless entry N.A.

Electronic Tripmlnder (avg. spd., fuel) N.A. Voice alM (list Items) N.A. Olher

Fuel door lock (remoce, key, electric) St-:inrlard . El P~tric. Remote Control Auto head on I elf delay, dimm ing N A Ccmering N.A Courtesy (map , reading) Onr-f .... ..,,,., nnmP./Man l .-fohf' (PArt of Lioht/Convenience Gro Door leek, ignilion NA . Engine compartment Ont--f nn<11l (p•,,.rt: of l-f aht: /Con"on-1 onro Groun)

Lamps Fog N. A. Glove compartment Oot--fnn<al (ps>rf' nf 1 -f O'ht-/Cnnu.on iPnr-P Groun) Trunk Ont-i """'1 (Ps:irt- nf T i ol,t /r.nnv~ni onr.o Groun ) Other Standard HiS?:h Mount Stop Lamp

Day/night (auto . man .) St:mda-rd Manual Mirrors L.H. (remote. pow« , heated) Standard , Remote Control

R. H. (conve•. remote, power. heated) Standard . Remote Cont r ol Convex Visor vanity (RH / LH, illum inated) N.A.

Pan<ing brake-auto rele115e (warning light) Standard, Pull Lever - Push Button Release Door lccl(s / deck lid - specify Optiona l. Power Door Locks/ Deck l id/Lift~ate Seat (2-4•6 way) Sport Performance Bucket Seats, Multi - Adjustable , heated ~river . pass, otherl lumbar , Ip, tl11gll su~rt power, manual) Articulated reclining f driver , pass

Power memorv 1·2 Dresel recllnel equipment Side windows Optio nal

Vent windows N.A . Rear window N.A. f'nnvPrt";'hlp Ton Ont-i nn::iol Retractab l e Power Too on Convertible

Radio Anlema (lccatlon , wh ip , wlshield , power) R-. H. Front Fender Mounted . Whio ayatems AM: FM, stero, tape; CB (a)

Speaker (number. location) Premium sound t!Yal f r:i;mt ,ms! R~a, Roof open airni•ed (flip-up, s11dlng, "T'') Ontinn<a l on 2- Dr. H~trnn<>r.k Onlv . Fl -fn-Uo/nnon A-f.r Speed control device Ont- • ~~"'1 R<11<>E! Speed warning devtce (light, buz:er ,etc.) NA. Tachometer (rpm) '-l'lrl() (Srrl ,.z/1,. f. nr 8 Cvl)• 7000 font w/'i . OT UI) EFI)

Theft protection-type N .A .

(a) Standard: AM/FM Stereo; Optional: AM/FM Stereo w/Cassette, Electroni c AM/FM Stereo w/Cassette

MVMA-C-86 Page 19

s

up)


CarUne ____ MU..;.;a.;S;.,;T_,AN..;...;:G..------,-------------ModelYear 1986 le&Ued __ 9._./ ...... 8..,.S ___ Reviaed(•) ____ _

METRIC (U.S. Customary) Car and BOdy Dlmenalons See Key Sheets for defini tions Al dimen&ion5 to ground are lot co,nparaliYe puflJOlft only. Dimensions are to be.__, tor all base body models of eo<:t,car line. SAE Ref. no. rete,s 10 the oefiNlion publlsned in SA£ Recommended Preclice Jl 100 '"McMor Vehicle Dimensions, .. unlesa~ apecitled .

TrNd l!ronl)

T,ur (r-)

Vehicle width

Body width at Sg RP (front)

Vehicle width (front dools open)

Vehicle width (rear doors open)

Front 19ndaf O\le,all width

Rear letlder -Ill widltl

Tumblo-home (d$Q.)

Length

WhNlbase

Vehicle length

Ove rha ng (front)

Overhang (rear)

Upper structure le"llffl

Rear wheel Ci L .. X .. ooord inate

Cowl point "X .. 000 rdinate

From end leng!n at cente rtme

Rear end lengtfl at centerl ine

Passenger di$tnbution (tron \lr earj

T runk.'cargo load

Vehicle heigfll

Cowlpoimt ogrou nd

Deel< point to grovnd

Rocker panel -tron l to ground

Bottom ot cloor closed -lron tto grd.

Rocket panel -rear to groo nd

Bottom ot door ctosed -rea r to grd.

Winclshield slope angle

Backi;gh1 Slope angle

Ground Clearance*

Front bumper to ground

Roar bumper lo ground

Bumper to ground llront at curb m 11S11 (WI.)]

Bumper to ground !rear atcurt>m ass(wt .tJ

Angle of approa cn (degrees)

Angle ot deperture (degreest

Ramp breakover ang le (oeg reesf

Axle ditletential to grou nd (tront rea r t

~ in . runn ing gro..nd cleara nce

Locat ionotmin . run. grd clear

UI! llef . No .

W101

W102

W103

W117

W120

W121

W106

W107

W122

L101

L 103

l 104

L105

L123

L127

L125

L126

Ll29

POt.2,3

H101

H11•

H138

H112

Ht 33

H111

Ht 35

H122

H121

H102

H104

HIOJ

H105

H106

H107

H147

H\53

H156

2~DOOR SEDAN CONVERTIBLE

1438 (56.6) 1448 (57.0) 14.t;S (69.1) 1735 (68.3) 3899 (153 S) N.A 1717 (67.6) 17SS (f,Q 1) ,i;. ,u ?i;. ,1.0

2/1 0 1323 (52.l) 1317 (51. 9) 9S9 (37.7) 892 (35.1) 193 (7.6) 2S7 fl0.l1 17 0 (6 .7 ) NA. i.AO

i_ 7 .1°

525 (20. 7) (a) 336 (13. 2)

532 (20 . 9) (a)

396 (IS .6) 18.60 18.6° 12.70 164 (6.5 ) 125 (4.9) (b) Converter Grass Shield

• AU venicle height and ground ctearanCfJs are made at the Man uh1c1urer's Oe111gn Load Weig ht , unless otherwise specified .

Manufacturers Des ign Load Weight is del ined with indica ted passenger distribution and vunk.'c:argo load.

(a) To Upper Flange of Parking Lamp Opening M.Jal~nimwn Clearance to Traction Bars (S,,~Je

2gnly) is 122 (4 . 8)

2-DOOR HATOiBACK

2s.2°

384

n?3 rs2. n

907 (,i;._7)

62.0°

MVMA Specifications Form car Une _..,_MU=S..::.T:.::AN;.;.G ____________ _____ _

Passenger Car METRIC l::;3y Customary)

Model Year_1_9_8_6 ___ Issued __ 9_/_8_5 __ Revised (•) ____ _

Car and Dimensions See Key Sheets for defi nitions

Front Compartment

5g RP front, '"X" coordinate

Effective head room

Mu. elf. legroom (accelerator)

SgRP to heel point

SgRP to heel point

Bacl<angre

Hipangle

Kr,eeangle

Foot angle

Design H-poif'lt front travel

Normal driving & riding seat lraci< trvl.

Shou~ rOom

Hiproom

Upper body opening to ground

Stffringwheel maximum diameter

Steering wheei angle

Accel. heel pl. 1011-. whl. cn11

Accel. heel pt 10S'-. whl. cntr

Steering wheel to C / L ol u,;gh

Steering whee l torso clearance

Headlining to root panel (front)

Undepressed floor covering thtclmess

Rear Compartment

5g RP Point couple c111ranca

Eltec:tiva head room Min. effective leg room

5g RP (second to heel)

Knee CIN 1'111108

Compattment room

Shoulder room Hip room Upper body opening to ground

8ackangle

Hipangle

KMeangle

Foot angle

Heecllining IO root penel (second)

Dep,asaed floor covering thlel<rt8S$

Lu gage Compartment

Utable luggage capa city (L (cu. ft.))

Liftover height

SAE Aet. 2-DOOR SEDAN No.

L31 3034 (40.7) H61 940 (37.0) l.3A 1059 (41 7) H30 223 (R 8) L53 R59 (.'.Pi 8) L40 2'-v L42 Q'li qO

L44 123 .3 ° L46 87v L17 178 (7.0) L23 155 (6 . 1) W3 1420 (SS,9) ws 1425 (56. 1) HSO' 1204 (47.4) W9 'l;f,R (ld . 5) H18 ?'li c;O L11 51,; (20 21 H17 i;QQ (23.6) H13 SI~ (?; d'\ L7 't,n r, ,; c; '\ H37 ?'li (0 g)

H67 20 _(I) a.SJ.

LSO 701 (27 . 6) H63 912 (35.9) L51 780 (30 . 71 H31 2r;7 (10 11 L48 - H (-1.1) L3 S84 (23.0) W4 1379 (54.3) W6 1196 (4 7 .1) HSt N.A. L41 21u L43 ,,o L45 M, 10 L47 111 si.O

H38 23 (0.91 H73 20 (0 , 8)

Vt

Ht95

lnterfor Volumes (EPA ClaHlflcaUon)

Vehicle class (subcompact, compact. Ille .) Subcomoact lnteriol'vOlumeinde• (cu. ft .) 93,8 Trunk/cargo itldex (cu. It.) 9 . 9

MVMA-C-S6 Page 21

CONVERTIBLE

Qc:;S (37 6)

1.:1 H i (SS 7)

940 (37 . 0)

t;f,1 (22 1) 1242 (48.9) 978 (~jl t;)

19v 70°

N.A.

87.4 6.4

2-DOOR HATCHBACK

QdO (37. 01

1420 (55.9)

904 ('li', .6)

f,07 ( 2.'LQ ) 1379 (54.3) 11 Qf, (47 . 1)

z4v 74.8v

95.9 12. 3_


Carline __ MU_S_T_AN_G _______ _ ________ _

ModelYear 1986 Issued 9/85 Revised(•) _____ _

METRIC (U.S . Custom ary) Car and Body Dimensions See Key Sheets for definitions

Body Type 1= No.

Station Wagon- Third Seat (NOT APPLICABLE)

$g RP COUl)ledistanee l85

Shoulder room wes Hip room W86

Effective legroom l86

Elfectiva head room H86

Sg RP to heel point H87

Knee clearance L87

Seat facing direction so, Back angle 1.88

Hip angle 1.89

Knee angle L90

Foot angle Ul1

Station Wagon - Cargo Space (NOT APPLICABLE) ca,gotength (open front) L200

Cargo length (open second) L201

Cargo lengtn {closed front) L202

Cargo length (closed second) l203

Cargo lengtti at belt (lront) l.204

Cargo length at belt (second) L205

Cargo width (wheelhouse) W20 1

Rear opening width at IIOOI' W203

Opening widlh at belt W204

Max. rearopen ,ngw id1h above belt W205 Cargo heigllt H201

Rear opening height H202

Tailgate to ground height H2SO

Front seat baclc to toad floor height H197

Cargovolumeindex(m 3(tt.")J V2

Hidden cargo volume (m3(1t. 3)) V4

Ca<go volume. index-<ear ot 2-seat v,o

Hatc hback - Cargo Space 2-DOOR HATCHBACK

Cargo length at front sean>ack height l.208 911 (38.Q) Cargo length at lloor (front) 1.209 11.0? (t:.t:. f.)

Cargo length at second seatback height l210 457 ( 18.0)' C3fgo teogth at lloor (second) l211 838 (33.0) Front seatDacl< to toad l1oor height H1i7 4~~ (1.8.....l)

$ecQ nd seat back to load floor heigh I H198 3RQ (g _3) Cargo volume index tm,(tt. 3 1) V3 .R.c-('Hl.0) Hidden cargo volume (m3(1t. 3 )) V4 NIA Cargo volume index-rear ot 2-seat V11 7;~ (12 3)

Aerodynam ics• 2- Door Sedan Convertib l e Wheel lip to ground. front 665.2 (26.2) Whe1!11iptoground. rear 657.9 (25.9) Frontal area (m'(tt2)) l.91 (20.6), (a) Drag coefficient (Cd)

• EPA Loaded Vehicle Weight, loading COfldiUons (a) I ncludes Two Outside Mirrors

MVMA-C•86 Page22

Car Line MUSTANG MVMA Specifications Form Passenger Car

Model Year_l;:;;.;9;;...8:;.;6;:._ _ _ IS&Yed 9/85 Revised(•) ____ _


Body Type I ALL MODELS

Ve hicle Fiduci al Ma rks

Fiducial Mark Def ine Coordina1e Location Number'

1 & 2 The rear vertical edge of the master contro l notch on the underside of Front the front door t"ocker panels locates the "Xi• coordinate relative to

body grid and is located at the 444 (17.S) line .

(Front Location) (Rear Location)

X - 444 (17.S) X - 1295 (5 1) y - 737 (29) y - 737 (29) z - -27 . 9(-1. 1) z - -35.6(-1.4)

3 & 4 The intersection of the horizontal -vertical surfaces on the rocker panel door rabbet locates the "Y" and "Z" coordinates relative to body grid at particular fore-aft inch l ines. The fore-aft location can be determined

Rear by the reference dimension from - Fiducial Marki and 2.

Fiduc ial Mark Number

W21 7'1,,7 (?Q'\ L54 A AA. ( 1 7 _ _c;)

Front H81 -27 . 9 ( - 1.1) Hl6l --1-1163 --

W22 737 (29) L55 1295 (511

Rea, H82 - 35 - fi ( - 1. 4 ) Hl62 --H164 --

• Reference - SAE Recommended Practice , JI 82, MolOr Vehicle Fiducial Marks. An linear dimensions are in millimeters (inches) .

MVMA-C-86 Page23


Car Line MUST ANG Model Year_ 19_86 ___ Issued


Body Type ALL MODELS

Lamps and Headlamp • Sh ape

Highest" 654. 8 ( 25 • 8_} Headlamp

{SAE- H127) Lowest --

Heigh! above Highest''

668 (26 . 3) ground to Ta~la'l center of bulb (SAE - 128) 01 marker Lowest

AN. 7 ( 19 ._ll Front

Sidem.ne, 641 (25 . 2) Rear

622. 3 (24 . 5) Inside

Headlamp 428 . 7 (16 . 9_} Outside ..

615.7 (24.2) Inside

Distance from CIL ol Cll 10 Taillamp 665 ( 26.2) ceiiter ot bulb Outside ..

6R2 (26 . 9) Front

Directional 620.7 (24.4) Rear

462.8 (18 . 2)

Lo beam Standard ~~ Hi beam .Standard (std .• op:., n.a.) Replaceable bulb No

Shat>e Dual. Rectan011lar. Halo11:en Lo beam N1A Hi beam N'A Headlamp Replaceable N'A olher u,an

above Shape N1A Type NIA

• Measured at curb mass (weight). ·• II single lamps are "sad enter here .

MVMA-C-86 Page24

9 /85 Revised(•) ____ _

car une MUSTANG MVMA Specifications Form Passenger Car

Model Year...:1:.:9;..::8:.:6~-- Issued 9/85 Revised(•) - ----


CURB MASS . kg. (waighl. lb .)" Model

Front Rear To1al

3, 8L J.nai.ne w/ 3-Snd. Auto. Trans.(C-51 and 45 Amn Batterv

?-"'- . I Y. C:a.l~n 743 539 1282 (1652) ~1197) (2849)

2-Door LX Hatchback 745 563 1':tng (1655) 125?) r20071

,___ ; 2-hnor LX ConvertihlP 772 C::OR n1n I (1715) 1329) (3044) I

' .. 5. OL EnQine w/5-Speed I

r··Manual Transmission

I __ 2-Door GT Hatchback 822 591 1413 : (1R?I.) 1 ~1') ( 311;0)

2-Door GT Convertible Rc;.n '-21 1471 risuun l°'Rl) (~?I.Q)

• Reference - SAE J t 100 Motor •1ehicle dimensions, curl> weight definttion . ""Shippi,"Omass(weightldafriion- Less Fuel and Engine Coolant

MVMA-C-86 Page25

Vehicle Mass (weight)

% PASS. MASS DISTRIBUTION SHIPPING Pass In Front Pass In Rear MASS. k~

(weight, lb. •• Front Rear Roni Rear

45 c::c:: 19 81 1 ??7 ( ?7?,; '\

4c;. c;.c_ 19 81 1 ?I: ':t

(?7R,i'\

A.I: c:: c:: 10 R.1 1 ':t 1 A

(2921)

4c;. c;. C. 10 81 t 'tl:C

('tfl11'I

Ai:: c;.c;. 10 81 1,111; ('{1,11)


Car Line MUSTANG Model Year .. 1-'9/iw6.,___ __ Issued _..:9:.../...,8_5.....,_ Relltled t•l ____ _

Optional Equipment Differential Maas (weight)9

Eq~ MASS , kg. (we ight, lb .)

Remarks Front Rea, T04el

POWERTRAINS: Ft,ir,Jf\JF

2 •n 4-Snporl u ,, .... -l _An _1 ?? _i;., _, M A ~n r ;hl ..

Trans. ( - 891 - 2 7'\ (-11i::..,

2.3L w/3-Snd A ,1tn . T,-:1nc - 1.i::.. c; -11 7 -.dS2 ? tJ A -- ,.. ___ ~n,1 .. (C-3) (-81 1 -261 ( -1071

3,8L w/4-Sveed AOD q_q _,; (,, 1 ~ c;.

Auto. Trane:.. (221 on ( ,I) J

S.OL w/5-Soeed 63.4 17.6 81 Tnc:}t1t"t1>c:c Hanrtl inP" Snc:cnnn,,; nn Manual Trans. (1411 (391 (J AO)

SJH w/4-"n .. ~d AOn S2? S2 'J.7Q 11n 7 Includ,,.c:. Handlino Susnenc:.i nn Auto. Trans. (1841 (62) (24f. '\

AXLES• Tra c.tion-Jnl, 3 AC D-,t-i n

w/? ,I & 4_,;::nri M- - -- () 7 7, ,., 1.

3-Snn A11t-n - T ran ,. rn, (c;.:\ (C'\ -

Traction-Lok. 3 OR Ratio 0 2.3 2.3 w/3.8L & 3-Spd,Auto,Tran: (O) (S) (S)

Tracti on-Lok. 3.27 Ratio 0 2.3 , ' w/5,0L rm (S) (£;)

TJDJ:-C: •

P205/70VR14 6.3 10 . 8 17 -1 b. 1 1 F.n u Pxc:P.n1: S OI (14) (24) ( 1.~'\ -

P225/60VR15 S.Q 6.3 17 ? w/5.0L En2. Onlv; Std. on GT (13) (14) (27) Tn r l,,rlac, H~nrll ina C:, ,, ..,,,.n.,;--

-

WHEELS: Aluminwn - SimulatP.d - .'L2 -~-(,, -f..R Snolr,,. (-7) r-in ( -1 ~-.

Steel - Polv cast 3.6 3.6 7 .2 (8) (8) ( 11')

• Also see Engine - Gene ral Section for dressed engine mass (weight) .

MVMA-C--86 Page 26

MVMA Specifications Form Passenger Car METRIC (U.S. Cust omary)

ca, Line J.IJSTANG Model Year...,1_98_6 _____ laued 9 /85 R9vlaed(•l-----

Optional Equipment Olfferen tlal Mass (weight)•

Equipm8"1 MASS, kg. (weigt,1, lb.)

Remarks F,ont Rear TOlal

WHEELS: (Cont• d.) Stvled Stee l .5 . 9 1. 4 C:i .. .. - 1 ;111~c c::11

(1) (2) (3)

WHEEL COVERS: Wire Tvoe .s d Q

(1) (1) (?)

MI sr.F.T r .<1Mi:n 11c: ,- , - 1 1 • ' "' :-. •

,1;.,. r..-. .. ,1; ~-inn -ino 1.o1/M~--·r,,mn rnn ~ -rnl w/?- ·u ? 7 c; n ?7 c;

(SO) (0) (SO)

w/3 . 8L ? 1 ? 0 ?1 ?

( ,17'\ (n'\ r 47'

w/5.0L 18 . 5 0 l R c:;

( 41'\ (0) ( ,11'\

Batteries· 36 Arnn ~an ue -3 2 - c; -? 7 Standard w/2.3L F. 4-Snil Mann<> 1

( -7) (l) ( - 6) Tra ns .

HD 54 Amn Ran Pe 2 . 7 -.4 2 . 3 Stanit,,,.;t w/r.r MnA .. 1 <>nil Tn r-1 nn

(6) (-11 rs, <>11 u ... ,1 .. 1 <:: w/n n + C: () I t: .. o - -45 Anm Ransi:e 0 0 0 Standard w/2 . 3L F. 3 - C:n il. Auto .

(O) (0) (0) Trans . <>nn w/7, RT J:no .

Console 1.8 1 ,1 '.L2 Standard on Hatchback 6 Convertible (4) (3) (7) Model s:Re ad . on Sedan w/5 . 0L 6

5- Snd Man.

Defroster. Rear Window 0 0.5 0. 5 N. A nn (" . v c ihle (0) (1'\ (1)

License Plate Bracket - o.s 0 0.5 Front (1) (0) (1)

Lismt Group - .5 1.4 . 9 Standar d on Convertib l e (-1) (3) (2)

• Also see Engine • General Sec1,on tor dressed engine mass (weight) .

MVMA•C-86 Page26 A


Car l ine _.:.;MU:,;;S.;T.:.:AN:.:.G::::.... ____ ~~----------Model Year-:a.19.,..8 __ 6 ___ lls&,ed _ ___,9.,_/...,85 ....... _ ReviHd (•) ____ _

Optional Equipment Dlffer ent lal Mass (weight)•

~ MASS, kQ. (weight, lb.)

Remark5 Fl'Ol'II Rear T0141

MISCELLANEOUS OPTIONS: (Cont ' d. ) RADIO SYSTEMS :

Radio AM1.EM StP1"PO - s ..0 - c; w/C::i.,_settP ( _ 1) (fl) '.._}_)

- .

Radio Del_ete AM/FM - 2 7 - 1 d -4 j

Stereo ( -1i) (-'U. ( _Q) - .

C:nunrl Svs1:Pm Pre.mi n m - 1 7; 7; _6 '2 7;

(-3) 1 81 LSJ

Power Lock r.rn11n 1 R , 7; ,t 1

( ,t) _[_t;,) (_Q) .

Power Side Windows l.8 9 '2 • .1_

(d) (2) (6)

Prat- Pr. ti nn Roar! .s 0 .5 _ Av:i.i lah l e_ C!'ln!'lrl:t On lY_ Abrasion (l_l ifil ill

Roof~ Fli.I!-Uo Open .Ai_i: s 6 3 1 1~.3. 111 A on 1. ··- :i h 1,. (11) 1 141 (25)

..

SEATS: Fro nt. Indrn dua l J.ti ah B::i.rl< - . 9 -1.8 -2.7 Reclining

-(-2) ( - 4) ( - 6)

Steerin1r ..whe.el Tilt g 0 9 (21 ffi ) (2. l

Soeed Contro l 2_. 7 1 8 4-----5. (6) (41 (10)

EMISSION SYSTEMS: California w/2.3L & .s 0 5 3-Sod. Aut o . Trans (1) (Q.) (1.l

California w/3 ~, s 0 _5 (1) __[fl 1 ( 1 )

Cal ifornia w/5.0L .s 0 s (1) (O) (l)

•Afso see Engine. Ge~eral Se(tioo ror cl•e$sed engine mass (weight),

MVMA-C-86 Page26B


Exterior Car And Body Dimensions-Key Sheet

SICTION A-A

Exterior Width

Exterior len&th & Height i-.- - - L1U -- ----- --lll ) ----- -+-- - Llll

r Hlll

ll'1 7 NIH

::L~N- ... .,o,1-1 ... _"1_u _____ lll:_m __ "_u_, ___ "' ..... 1~ .. I ... --u05:_:: __ .-- - -- --- --- --llll ----- ----- - --4

Exterior Gro11nd Clearance

MVMA•C-86 Page27


Interior Car And Body Dimensions-Key Sheet

MVMA-C-86

AOOf PAIIEL CAI

HUOUNI-G C/lO r · Hll

,- HUOLIIHNG • C/LO

Page28

MVMA Specifications Form Passenger Car METRIC (U.S. customary)

Third 8Nt

--- - UM---.......i

14-----UDI -t-- -.-i

----ll02----------uoo - - -- -

Car10 Space

MZ50

Station Waton

Hatchback

Page29

U 11

MVMA Specifications Form Passenger Car METRIC (U.S. Customary )

Ext•rtor Car And Body Dtm•n•lons - K•y Sheel Dimension s Defini tions

Seating Refer•nce Point SEAT ING REFERENCE POIN T means the manufacturer's design reference point wt\ich -(a) Es1ablishes the rearmost normal design driving or riding position of each designated sealing position in a vehicle; (b) Has coordinates established relative to the design vehicle structure: (c) Simulates the position of the pivot center of the human torso and !high ; and (d) Is the reference point employed to posit ion the two d imensional templates desc ribed in SAE Recommended Pract ice J826, " Devices for Use in Defining and Measuring Vehicle Seating Accommodations ,"

Wid th Dimension a

W10 1 TREAD- FRONT . The dimension measu red between the tire centerlines at the ground.

W102 TREAD-REAR . The dimenSion measured between lhe tire centerlines at the ground . In case of dual wheets. the dimension will be measured to the cente rline of tire and wheel assembl ies .

W103 VEHICLE WIDT H. The max imum dimension measured between the widest point oo the vehicle, excluding exterior mirrors, flexible mud flaps, marker lamps, but including bumpers , mold ings. sheet metal protr\Jslons or dual wheels, if standard equ ipment.

W106 FRONT FENDER WIDTH . The dimension measured be· tween the w idest points at the front wheel centerline. excluding moldings.

W107 REAR FENDER WID TH. The dimens ion measured betwee n the widest points at the rear whee l centerline , excluding moldings.

W117 BODY WIDTH AT SgRP-FRONT. The dimension measured laterally between the widest points on the body at the SgAP front, excl uding door handles. applied moldings. or appliques .

W120 VEHICLE WIDTH-FRONT DOORS OPEN. The dimension measured between the widest point on the front doors in max imum hold-open position .

W121 VEHICL E WIDTH-R EAR DOORS OPEN . The dimension measu red between the widest point on the rear doors in maximum hold-open position . For vehicles with a rear door on only one side, this dimension is to the zero ·y· plane .

W 122 TUMB LE-HOME. STRAIGHT SIDE GLASS. The angle measured from a vertica l to the outside surlace of the front door glass atthe SgRP "X" plane . CURVED SIDE GLASS . The angle measured from a vertical to a chord exlending from the upper OLO to the lower DLO at the ou tside surface of the front door glass at the front SgRP " X'"plane.

Length Dlm•n alona

• L 101 WHEELBASE (WB) . The dimension measured longitudinally between front and rear wheal centerl ines . In case of dual rear axles . the dimens ion shall be to the midpoint of the center ~nes ol the rear w~ts.

L103 VEHICLE LENGTH. The mllllimum dimension measured longitudinally between the foremost point and the rearmost point on the vehicle , including bumper, be.Imper guards , tow hooks and /or rub strips, if standard equipment.

l104 OVERHANG-FRONT . The dimension measured longhudi• nal ly from the centerline of the tront wheels to the foremost point on the vehicle including bumper. bumper guards, tow hooks aodlor rub strips , ii standard equipment.

L105 OVERHAN G-R EAR. The dimension measured longitudi• naMy from the centerline of the rea, wheels; or in the case of

MVMA-C -86

dual rear axles. the d imension sha ll be the midpoint of the centerlines of the rear wheels , to the rearmost poin t on the vehicle. including rear bumpers. bull1)8r guards, tow hooks and rub strips , if standard equipment.

L 123 UPPER STRUCTURE LENGTH. The dimension measured longitudinally from the cowl ·point to the deck po int.

Lt 25 COW L POINT" X'" COORDINATE. L 126 FRONT END LENGTH . The dimension measured longillJdi·

nally from the cowl point to the foremost point on the vehicle at the zero "Y"' plane excluding ornamentation or bumpers. In cases where b\Jmpers and/or grills are integrated with the profile. measurement is made at the foremost point of front end contour .

l127 REAR WHEEL CENTER LI NE "X" COORDINATE or in the case of dual rear axles . the coord inate shall be the midpoinl of the dista nce between the rear axle center11nes.

L129 REAR ENO LENGTH. The dimension measured longitud i• nally from the deck point lo the rearmost visible po int of the body sheet metal at the zero "Y" plane . excludJng ornamen talion or bumpers.

Height Dimensions

H101 VEHIC LE HEIGHT. The dimension measured vert ica lly from the highest point on the veh icle body to ground.

H111 ROCKER PANEL- REAR TO GROUND . The dimension measured vertically from the bottom of Iha rocker or side quarter panel at the front of the rear Wheel opening , exc luding flanges , to ground .

H1 12 ROCKER PANEL-FRONT TO GROUND . The dimension meas ured vertieally from the foremost po int on the bottom ol the rocker panels, excluding flanges. to ground .

Hl 14 COWLPOJNTTOGROUNO. Measured atzero "Y'" plane. H121 BACKLIGHT SLOPE ANGLE. The angle between the vertl•

ca l reference line and the surface of backii ght at veh icle zero " Y" plane . For curve backl ight, the ang le is to cho rd ol back• ~ght arc from lower DLO to upper DLO.

H 122 WINDSH IELD SLOPE ANGLE . The angle between the verti cal reference line and a chord of the w indshield arc running from the lower DLO to the upper DLO at the vehicle zero "Y" plane. In the case of wrap over glass , the angle lo be measured wm be formed by a chord 457 mm (18.0 in) long drawn from the lower DLO to the intersecting point on the windshield.

H127 HEADLA MPTOGROUND-CUR B MASS(WT ,). The dimension measured vertically from the center line of the lowest headlamp tens to ground .

H128 TAI Lt.AMP TO GROUND-CUR B MASS (WT.). The dimension measured vert ically from the centerline of the upper bulb to gro und.

H133 BOTTOM OF DOOR CLOSED-FRONT TO GROUND . The dimension measured vert icaUy from the bottom oulside corner of the door on the lock plffar side. in maximum closed pos ition, to ground .

H 135 BOTTO M OF DOOR CLOSED-REAR TO GROUND . The dimension measu red vert ically from the bottom outside corner of the dOOr on the lock pillar side. in maximum closed Position, toground.

H138 DECK POINT TO GROUND . Measureda t zero"Y " plane.

Ground Cluranc e DlmenMons

H102 FRONT BUMPER TO GROUND . The minimum dimension measured vertically from the lowest point on the front bump er lo ground, including be.Imper guards, if standard equipment.

H103 FRONT BUMPE R TO GROUND-C URB MASS (WT.). Measured inthe samemanner as H102.

Page30


lnterlo, Car And Bocly Dimension• - Key Sheet Dimension• O.flnltlon•

H104 REAR BUMPER TO GROUND . The minimum dimension measured vertica lly from the lowest point on the rear bumper to ground , including bumper guards , ii standard equipment.

H105 REAR BUMPER TO GROUND-CURB MASS (WT.). Measured in the same manner as Ht 04.

H106 ANGLE OF APPROACH. The angle measured between a tine tangent to the front tire static loaded radius arc and the Initial point of structural interference forward of the front tire to ground. The ~miting structural component shall be designated .

H107 ANGLE OF DEPARTURE . The angle measured between a line tangent to the rear tire static loaded radius arc and the initial point of structural Interference rearward of the rear tire to ground. The limiting component shall be designated.

H147 RAMP BREAKOVEA ANGLE. The ang le measured between two lines tangent to the front and rear tire stalic loaded rad ius and Interse cting at a point on the underside of the vehicle which defines the largest ramp over wh ieh the vehicle can rol l.

Ht 53 REAR AXLE DIFFERENTIAL TO GROUND. The minimum dimension measured from the rear axle d ifferent ial to ground.

H156 MINIMUM RUNNING GROUND CLEARANCE . The mini• mum dimension measured from the sprung veh icle to ground. Specify location.

GlasaAreas

St Windsn ield area . S2 Side windows area . Includes the tront door , rear door, vents,

and rear quarter windows on bOth sides of the veh icle. S3 Backlight areas. 54 TOlalare a.Totalofallareas(S1 + S2 + $3).

Fiducia! Mark Dimensions Fiducia! Mark-Number 1 "X" coordinate . LS4

W21 H81 H161 H163

LSS W'l2 W82 H162 H164

"Y" coordinate. "Z" coordinate. Height "Z'" coordinate to ground at curb weight . Height "Z'" coordinate to ground. Fiducia! Mark- Number 2 "X" coordinate . "V" coordinate. "Z"' coordinate. Height "Z" coordinate to ground at curb weight. Height "Z" coordinate to ground .

Front Compartment Dlmenalons

L7 STEERING WHEEL TORSO CLEARANCE. The minimum dimens ion measu red in the side view from the rearmost edge of the steering wheel, wilh front wheels in the straight ahead position, totnetorsoline.

L11 ACCELERATOR HEEL POINT TO STEER ING WHEEL CENTER. The dimension measured horizontally from the AHP to the intersection of the Slffring column centerline and a plane tangent lo the upper surface of the steer ing whee l rim.

L 17 DESIGN H-POINT-FRONT TRAVEL . The dimension measured horizontally between the design H-point-front in the foremost and rearmost seat traek Positions.

l.23 NORMAL DRIVING AND RID ING SEAT TRACK LEVEL. The dimaosion measured horizontally between a point on the design H-point travel line from the SgRP to the displaced point on the design H-poil'lt travel line with the seat moved to the foremost seat J)OSilion, but not to include seat traek travel used !or purposes other than normal driving and riding positions.

L3t SgRP-FRONT . ··x .. COOROINATED .

MVMA-C-86 Page 31

L34 MAXIMUM EFFECTIVE LEG ROOM-ACCELERATOR. The dimension measured atong a line from the ankle pivot center to the SgRP - lront plus 254 mm (10.0 in) measured with right fool on the vndepressed accelerator pedal. For vehicles with SgRP to heel (H30) grea ter than 18 in .. lhe accelerator pedal may be depressed as specified by the manufacturer . II the accelerator is depressed , the manufacturer shall place fool Hat on peda l and note the depress ion of the pedal.

L40 BACK ANGLE-FRONT . The angle measured between a venica l line through the SgRP-fronl and the torso line. If the seatback is adjuSlable. use the normal driving and riding pos• ition specified by the manufacturer.

L42 HIP ANGLE-FRONT . The angle measured betWeen torso line and thigh centerline .

l44 KNEE ANGLE~RONT. The angle measured between thigh centerline and lowe r leg centerline measured on tile right leg.

L46 FOOT ANGLE-FRONT . The angle meas ured between the lower leg center line and a line tangent to the ball and heel of the bare foot flesh line measured on the right leg. Ref SAE J826.

L53 SgRP-F RONT TO HEEL. The dimension measured hori· zontatly from the SgRP-lront to the accelerator heel point.

W3 SHOULDER ROOM-FRONT . The minimum dimension measured laterally between the trimmed surfaces on the ·x .. plane through the SgRP-front at height between the belt Mne and 254 mm (t0.0 in.) abOve the SgRP-lronl excluding the dOor assist strap and attaching parts .

W5 HJP RO~RONT . The minimum dimension measured late011ty between the trimmed surfaces on the ·x·· plane through the SgRP-front within 25 mm ( 1.0 in.) below and 76 mm (3.0 in.) above the SgRP- front and 76 mm (3 .0 in.) fore and alt of the SgRP-lront.

W9 STEERING WHEEL MAXIMUM OUTSIDE DIAMETER. De· fine ii other than round.

H 13 STEERING WHEEL TO CENTERLINE OF THIGH. The min• imum · dimens ion measured from the bottom of steering wheel, with front whee ls in the straigl\t position. to the thigh centerline.

H17 ACCELERATOR HEEL POINT TO THE STEERING WHEEL CENTER. The dimension measured vertically from the AHP-lront to the intersection of the steering column centerline to a plane tangent to the upper surlsce of the steering wheel rim .

H18 STEERING WHEEL ANGLE. The angle measured from a vertical to the surlace plan e of the steerin g wheel.

H30 SgRP-FRONT TO HEEL. The dimensio n measured verti• cally lrom the SgRP-front to the accele rator heel point.

1-137 HEADLINING TO ROOF PANEL - FRONT . The d imension measured from the intersection ol the headlining and the extended effective head room line normal to the sheet metal.

H50 UPPER BODY OPENING TO GAOUND-FRONT . The di• mension measured vertica lly from the trimmed body opening to the ground on the SgRP-front ··x·· plane .

1-161 EFFECTIVE HEAD ROOM-FRONT . The dimens ion mea· sured along a line 8 deg. rear ol vertical from the SgRP....froot to the headlining plus 102mm (4.0in .).

H67 FLOOR COVERING THICKNESS-UNDEPRESSEOFRONT . The dimension measured verllcaUy from the surface of the undepressed floor cove ring to the underbody sheet meta l at tl'18 accelerator heel po int.

P01 PASSENGER DISTRIBUTION -FRONT ,

Rear CompartmantDlmen • lons

L3 COMPARTMENT ROOM- SECOND. The dimension mea• sured horizontally from the back of front seat 10 the front of the second sealbaek at a height tangent to the top of the second seat cushion.


Interior C• r And Body Dimensions - Key Sheet Dimensions Detlnhlons

LA1 BACK ANGLE-SECOND. The angle measured between a vertical line through the SgRP-second and the torso llne.

L43 HIP ANGLE-SECOND . The angle measured between torso Nne and thigh cener1ine.

L45 KNEE ANGLE-SECOND. The angle measured between thigh centerline and lowe r leg centerline .

L47 FOOT ANGLE-SECOND . The angle measured between the lower leg centerline and a line tangent to the ball and heel of the three-dimensional devices bare foot flesh line (Referenc:e J826).

L48 KNEE CLEARANCE-SECOND. The minimum dimension measured from the knee pivot cet1ter to the back of front seat• back minus 51 mm (2-0 In.).

LSO SgRP COUPLE DISTANCE-SECOND. The dimension measured horizontally from the driver SgRP--h'ont to the SgRP--second.

L51 MINIMUM EFFECTIVE LEG ROOM-SECOND. The dimension measured along a line from the ankle phlot center to the SgAP-secondplus254mm(10.0in) .

W4 SHOULDER ROOM-SECOND. The minimum dimension measured laterally between door or quarter trimmed surlaces on the "X .. plane through the SgRP-seconc:t at height between 254-406 mm (10.0-16 .0 in.) above the SgRP-sec• ond. excludi ng the door assist straps and attaching parts .

W6 HIP ROOM-SECOND. Measured in the same manner as ws.

H31 SgRP- SECOND TO HEEL. The dimension measur ed ver1i• caly from the SgRP--seoond to the two dimensional device hee l point on Iha depressed floor covering.

H38 HEADLINING TO ROOF PANEL-SECOND. The dimension measured from the intersection of the headlining and the ex• tended effective head room tine normally to the roof sheet metal.

H51 UPPER BODY OPENING TO GROUND-SECOND . The cli• mansion measured vertically lrom the trimmed body opening to the ground on the "X" plane 330 mm (13.0 in) forward of the SgRP-second.

H63 EFFECTIVE HEAD ROOM-SECOND. The dimension measured along a line 8 deg rear of vertical from the SgAP to the headlining. plus 102 mm (4.0in).

. H73 FLOOR COVERING-DEPRESSED-SECOND. The dimension measured vertica lly from the heel point lo the underbody sheet metal.

PD2 PASSENGER DISTRIBU TION-SECOND.

Luggage Compartmen t Dimension a

V1 USABLE LUGGAGE CAPACITY-Total of volumes of individual pieces of standard luggage set plus H•bo><es stowed In the luggage compartment in accordance with the proce• dure described in paragraph 8.2 of SAE·J t 100.

H195 LIFTOVER HEIGHT. The dimension measured vertically from the luggage compar1ment lower opening at the zero "Y" plane to ground .

Interior Volumes (EPA Clualflc •Uon)

Th!' Interior Volume Index is listed lor each body style eKcept two seaters. The interior volume index eslimates the space in a car. It is based on four measurements - head room. shoulde r room. hip room, and leg room - for the front and rear seats. plus trunk capacity. The interior volume index is an estimate of lhe size of the passenger compartment.

The Trunk •Cargo Index is an estimate of the size of the trunk/cargo space. In station wagons and hatchbacks it is an estimate of the space beh ind the second seal.

MVMA-C-86 Page32

Station Wagon- Third Seat Dimensions

L85 SgRP COUPLE DISTANCE-THIRD. The dimension measured horizontally from the SgRP-second the the SgRPthlrd.

L86 EFFECTIVE LEG ROOM-THIRD. The dimension measured along a line from the ankle pivot center to the SgRP-third plus 254 mm (10.0 in).

L87 KNEE CLEARANCE-THIRD. The minimum dimension from the knee pivot center to the back of second seatback minus a constant of 51mm (2.0 in). Wit h rear-lacing third seat. di• mens ion is measured to closure.

L88 BACK ANGLE - THIRD. Mesured in the same manner as L41 .

L89 HIP ANGLE-THIRD. Measured in the same manner as L43. L90 KNEE ANGLE - THIRD. Measured In the same manner as

L45. L91 FOOT ANGLE-TH IRD. Measured in the same manner as

L47. W85 SHOULDER ROOM-THIRD . Measured In the same manner

asW4. W86 HIP ROOM-TH IRD. Measure d in the same manner as W5. H86 EFFECTIVE HEAD ROOM-THIRD . The dimensiOn. mea

sured along a line B deg. rear from the SgRP--third 10 the headlin4ng rear of vertical plus a constant of, 02 mm ( 4.0 In.).

PD3 PASSENGER DISTRIBUT ION-TH IRD. S01 SEATFACINGDIRECTION -T HIRD .

Station Wagon-cargo Space Dlm• nsions

l200 CARGO LENGTH-OPEN-FRONT . The minimum di~ sion measured longitudinally from the back of the front seatback at the height of the Utldepressed float covering to the rearmost Point on the undepressed floor covering on the open tailgate 01 cargo surface if the rear closu re is a conventional door lype tailgate at the zero "Y" plane .

l201 CARGO LENGTH-OPEN-SECOND . The dimension mea• sured longitud inally from the back of the second seatback at the height of the undepressed floor covering to the rearmost paint on the undepressed floor covering on the open tailga te or cargo floor surface if the rear closure is a conventional door type tailgate. at the zero ··y " plane .

L202 CARGO LENGTH-CLOSED-FRONT . The minimum dimension measured hor izontally from the back of the front seat at the height of the undepressed floor covering to the rearmost paint on the undepressed floor covering on the closed tailgate or taildoor for station wagons; trucks and mpv's at the zero "Y" plane.

L203 CARGO LENGTH-CLOSED-SECOND. The dimension measured horizontal ly from the back of the second seat at the height of the undepressed floor cover ing 10 the rearm ost Point on the undepfessed floo, eOYering on the clOsed lailgale or la ildoor tor statio n wagons. trucks and mpv·s al the zero "Y" plane.

L204 CARGO LENGTH AT BELT....f'RONT. The minimum dimen• sion measured horizontally from the back of the front seatback at the seatba ck top to the foremost normal surface ol the closed tailgate or Inside surface of the cab backpanel at the height of the bell, on the zero "Y" plane .

l205 CARGO LENGTH AT BELT-SECOND. The minimum di• mens ion measured horizontally from the back of the second seatbaek at the seatback tap to he loremost normal surface of lhe closed tailgate al the height of the be lt. on the zero "Y" plane.

W20t CARGO WIDTH-WHEELHOUSE. The minimum dimension measured laterally between the trimmed wheelhousings al floor level. For any vehicle not trimmed, measure to lhe sheet metal.


Interior C.r And Body Dimension• -Key Sheet Dimension• Definitions

W203 REAR OPENING WIDTH AT FLOOR. The minimum dimen• sion measured laterally between the limiting interferences of the rear opening at floor level.

W204 REAR OPENING WIDTH AT BELT . The minimum dimen• sion meas ured laterally between the limiting interferences of the rear opening at belt height or top ot piek up box.

W205 REAR OPENING WIDTH ABOVE BELT . The minimum di· mension measured laterally between the limiting interfer• ences of the rear oPening above the belt height .

H197 FRONT SEATBACK TO LOAD FLOOR HEIGHT . The di• mension measured ver1ically from the horizontal tangent to lhe top of the seatback to the undepressad floor covering.

H201 CARGO HEIGHT . The dimension measured vertically from the top of the undepressed flOOr covering to the headlining atthe rear wheel .. x·· coord inate on the zero "Y" plane .

H202 REAR OPENING HEIGHT . The dimension measured verti• caly from the lop of the undepressed floor covering to the upper tri mmed opening on the <'.ero "Y" plane with rear door fully open.

H250 TAILGATE TO GROUND CURB MASS (WT .). The dimension measured vertically from the top of the undepr essed floor cove ring on the lowered tailgat e to ground on the zero "y· ·p1ane .

V2 STATION WAGON Measured in inches:

W4 x H201 x L2O4 1728 =11 3

Measured in mm: W4 X H201 X l.204

1 a9 "" m3 (cubic meter)

V4 HIDDEN LUGGAGE CAPACITY-REAR OF FRONT SEAT .

V5

V6

V8

V10

The total volumes of individual pieces of one set of standard luggage stowed in any hidden cargo area below the load floor rear of the front seat.

TRUCKS ANO MPVS WITH OPEN AREA. Measured in inches:

L506 x W500 x H503

1728 Measured in mm :

L506 x W500 x H503 3

109 - m (cubicmeter)

TRUCKS ANO MPV 'S WITH CLOSED AREA . Measured in inches:

L204 X W500 X H505 = ft3 1728

Measured in mm: L204 x W500 x H505 3

109 - m (cubiemeter)

HIDDEN LUGGAGE CAPACITY-REAR OF SECOND SEAT. The total volume of individual pieces of one se t of standard luggage stowed in any hidden cargo area below the load floor rear of the second seat. STATION WAGON CARGO VOLUME INDEX . Measured in inches:

H201 X L205 XW4 t W201 2 --- - 1728 _____ = fl3

Measured in mm:

H201 xL205xW 4 t W20l 2 ----- 106....,.....-----• m3 (cubiemeter)

MVMA-C--86 Page33

Hatchback-Cargo Space Dimensions

All hatchback cargo dimensions are to be taken with the front 5981 In lull down and rear position, and the rear seat folded down. The hatchback door is in the closed position . (For electrical1y adjusted seats, see the manufacturer's specif1Cations lor Design "W Point).

L208 CARGO LENGTH AT FRONT SEATBACK HEIGHT . The minimum hor izonta4 dimens ion from the "X'' ptane tangent to the rearmost surface of the driver's seatback to the inside limiting Interference of the hatchback door on the vehicle zero "Y" plane.

l.209 CARGO LENGTH AT FLOOR-FRONT-HATCHBACK. The minimum horizonta l dimens ion measured al floor level from the rear of the front seatback to the normal Umiting interfer• ence of the hatchback door on the vehicle zero "Y"' plane.

L210 CARGO LENGTH AT SECOND SEATBACK HEIGHTHATCHSACK. The minimum dimension measured from the "X" plane tangent to the rearmost surface of second seat• back or the load lloor which is stowed at least one hall of the H198 dimension height above the rear load floor , to the rearmost inside Hmiting lnterferenceon the zero "Y"' plane.

L211 CARGO LENGTH AT FLOOR-SECOND HATCHBACK. The minimum horizontal dimens ion measured at floor level from the rear of the second seatback or load floor panel to the normal limiting interference of the hatchback door on the vehicle zero "Y" plane .

H197 FRONT SEATBACK TO LOAD HEIGHT . The dimens ion measured vert ically from the horizontal tangent 10 the top of the seatback to the unclepressed floor covering.

H198 SECOND SEATBACK TO LOAD FLOOR HEIGHT: The dimension measured ver1icaffy from the second seat back to the undepressed floor cover ing.

V3 HATCHBACK .

V4

V11

Measured In inches· L,208 + L209x W4 x H197

------------ It 3 1728

Measured in mm:

L208 + L209x W4 x H197 __ __.. ________ E m3 (cubic meter)

109

HIDDEN LUGGAGE CAPACITY-REAR OF FRONT SEAT . The total volumes cl Individual pieces of one set of standard luggage stowed in any hidden cargo area below the load floor rear of the front seat. HATCHBACK CARGO VOLUME INDEX . Usable luggage (one (1 l stand and luggage set) below floor: Measured In inches:

L.210 + l2ll xW4xH198 2 -- - -172_8 _____ ~

Measured In mm: L2lO + L2l l lC W4x H198

2 ----

1-di~- ---= m3 (cubicmeter)

MVMA Specificat ions Form Passenger Car METRIC (U.S. Customary)

Index

Pap No,

Aerodynamics .............................................................................................. 22 Alternator ......................................... ............... ............. ............... .... ........ ... 16 Automali<: Transmislion/Transaxle .............. ................ ..... ................. ....... 6. 9 Axis, Steering ............ - ... ···-····· .......... _ ......... __ ,.._ .................. _ •• _. 1<1 Aide. Drive, Fronl. Rear ..... _ ...................................... _ .................... 2. 9. 10 Ax1e Shafts .. .... ·-·---· ··· .. ······ .. -· ......... - ...................... ....... - ..... 10 Ball8ry ....... ..................... _._ ................ _ ........... - .... _ ................ ..... ·-···· 16 Body end MiSCeUaneous lnformallon .................. - ................. _ .......... - .... 17 Brakes--P811llng. service ................................ - .................................... 12. 13

camber ........................................................................................................ 15 Camshaft ....................................................................................................... 3 Capac ities Cooling System ................................................. ...... ............. .......... ............ . 5 F11el Tri ..... - ... - ................................................................. - ...... _ .. _ 6 Lubncants Engine CfankcaSe ....... .,_ ............... _ ............ - ....................................... 4 Transmission/Transaxle ....................................... •--· .. ··---- 8. 9 Re.- Aide .......................... .................... _ .............................. ............ - ... 10

Car Models ............... - ....................... _____ .............. - ........... _.. 1 Car ar.d Body Oimensionl

Widlt, .... ................. .... .................................................... ......... ............ ....... 20 Length ............................................................ . ................................. 20 He ight ................... ................................... ............................. ......... ............ 20 Grouncl Clearance ........ ....................................... ...................................... 20 From Compartment .......................................... -............ .. .. - ...... ...... ... 21 Rear Companment ..................... _ ................. .......... .......... _ .................... 21 ~ Compa,tmenl ........................ _ ................... ·-····--· ... - ......... 21 Station Wagon- Third S.11 ......... .......... ................................. ................. 22 si.tlon Wagon - c.rgo Space ........................................... _ .......... - .... 22 Ha(Chbaelt - Cargo Spece ........ .................... .................... - ..................... 22

Calb.lrlttor ............................................................................ ·-·- .. ·-· ....... 2. 6 caster ... - .............................. ............................ ............ .......................... 15 Choke. iwtomatic .......................................................................................... 6 Clutch - Pedal Oparated ........................................... .... ........ .... .......... ......... 8 Coi l. Ignition ................................................................................... . ............ 16 Connecting Rocls ........................................................................................... 4 Convenience Equipment ....................................................................... __ 19 Cooling Sysiem .................................................................... _ ...................... 5 Crankshaft ............................................................... _ .................................. 4 Cytindera and Cyincler Heacl ............... _ ........................................ _ .......... 3

Diesel lnforma1ion .............. - ................ _ ......... -............. ............ - ....... 4 Oimens ion Definitions

Key St.II - Ex1eri0r .................................................................... 27. 30. 31 Key Sheet - Interior ......................................................... 28. 29. 31. 32, 33

Elect rical System ................................................................... ...... .......... ts. 16 Emission Controls ......... ......................................................... ......... ... - ........ 7 Engine-General Bore, Suoke, TYl)e ...................... - ......... - ................................................ 3 Compression Ratio ................ ............. ........ ................. _ ............................. 2 Disp9ClfflllM ................................................................................. - ....... 2, 3 Aring Order. Cylinder Numbering .............................................. _ .............. 3 General lntormation, PoWlt & Torque ........................................................ 2 Intake System ................ - ........... - ............................................... _ .......... • f>ower Teems ............................................. ............ .......... ........................... 2

Extiaust System ......................... ..... ...................... . ....................................... . 7 Eqy ipment Avallabllily, Convenience .......................................................... 19

Fan. Cooling ......................................................................... _ ........... - ........ 5 Fiducial MIIIQ .............................. - ......................... - ...................... - ...... 23 Filters - Engine Oil . Fuel System .................................... m .......................... 4 Frame ........... - ....... _ ................... - ................................................... _ .. _ 17 Front Suspension ............... _._ ................ - .............................. ........ - ..... 11 Front wi-1 Drive Unit .......... - ..................................................... -·-·- ··· 10 Fuel System ..... - .................... .. __ .... - ............... _ ...................... ........... ... 6 Fuel Injection ....................................................... .. ........................................ 6 Fuel Tank .............. ..... ................................. .................. .... ........ ................. 6

Generator and Regulator .... ..... .. ... ............... .............. ...... ...... ... ....... ....... .... 16 Glass ............................................... .................................................. .......... 18

Heaclroom - Body .... - .......... - ......................................................... -. 21. 22 Heights - Car and Body ................................... _ ................ - ... - ... - ....... 20 Homs ........................ - .......... _ ............. -- ........ ·-····- ..... - ..................... 15 Horaepower- Brake -·-· .. ·--·-· .. ·· .. ·-····· ................................................ 2

lgnilion System -· .. -· ..... - ............................... - ... - - .... _ ................... 16 Inflation - Tires ...... .............. ....................................................................... 13

MVMA-C-85

Paa•No.

lnl erior Volumes .......................................................................................... 21 Instruments .................................................................................................. 15

Lamps and Headlamp Shape ..................................................................... 24 Legroom ................ - ............................................................................. 21. 22 l.englt,s - Car and Body ........... .................................................................. 20 Leveling. s~ .................................................................................. 11 Llllers. Valve ................................................................................................. <I Linings - Clutch, Brake ...... - ...................................... .......... .................. 8. 12 Lubrication - Eligir,e Transmission-'Tranaaic le ........... ................. ......... 4, 8 . 9 Luggage Compartment ............................................................................... 21

Mass ................................................................................... , .................. 25. 2fi Models ................................................................. ___ ......................... I Motor Starting ...................................................................................... ..... _ 16 Muffle r ........................................... w .............. _. ___ ........................ "•" 7

Passenger Capacity ................... - .......................................................... ...... 1 PaAenger Mass Oislribu1ion ...................................................................... 25 Pistons ................................................................................... ....................... , 3 P- Brakes .......................................... • ...... ................................. ... ..... 12 Power, Engine .......... ....................................... , ................................. ............ 2 Po- Steering ................................................................... ......................... 14 ~Teams ............................................................................... ....... . ........ . 2 Propeller Shall. Universa l Joints ................................................................. 10 f>umps - Fuel .......................................................................... .... .................. 6

Waler ................................................. ............................................ ..... ......... 5 Ra<ia tor - cap. Ho-. Core ....................................................................... 5 Ratios - Axle, Transaxte ........................................................................... 2, 9 Cornprestion ............................................................................................... 2 Steering ..................... .................... ................................ ........... ....... .......... 14 TranamisaiQn/Transaxte ..................................................................... 2. 8. 9

Rear Axle ........................... ........ ............................................ ............ 2, 9. 10 Regulator - O.nerator .. ............ ... . .. . ... .. .. . . . . ... ............ ................. ... .... . .... .... 1 e Restraint S~ ......................................................................................... 18 Rim s ................................. .......................................... , ................................ 13 Rods - Conn.c:dng ....................................................................................... 4

Scrub Radius ............................................................................................... 14 Seats .............. _._ ...................................................................................... 17 Shock Absorbers, Fronl & Rear .................... _ .......................................... 11 Spa,k Plugs .................................. ... ........................... .... .. ...... .... ................. 16 SplNldometal ............................................................................................... 15 Springs - Front & Rear Suspension .......................................... ................. 11 Stabllfier (Sway Bir ) - Front & Rear ......................................................... 11 Starting System ••• ... ...... ........ ... ........ .... .... ... ... .... ...... . ........ ... ... ............ ......... 16 Steering ....................................................................................................... 14 5" pp,e,,ion - lgnl!lon. Radio ..................................................................... 18 5"51)8nsion - Front & Rear ........................................................................ 11

Tail Pipe ........................................................................................................ 7 Theft Prolectlon • .. ............. ........... ........................................................ 19 Thermoelal. Cooling ............................................................. _ ...................... 5 Tl!$$ ............................................................................................................ 13 Toe-In ............................... _ ........................................................................ 15 Torque Converter .......................................................................................... 9 Torque - Engine .................................................................................. 2, 8, 9 Transaxle ... ................... . ....... ....................... ................................... . .............. 9 Transmission - Typee .......................................................................... 2, 8, 9 Transmission - Aulomatic .. .. ...... ... ..... . .... .... ....... ............ ......... ... .......... 2. B. 9 Transmission - Manual ..... ........ ................................... . ....................... 2. 8, 9 Transmission - Ratios ............................................................................. : 2. 9 Trelld ..................................................................... _ ................................... 20 Trunk Cargo Load ............................................................................... . ......... 1 Trunk Luggage Capac:ily ............................................................................. 2 1 Turning Oiameter ............................ ............................................................ , 4

Unitized Construction ........ .... ............... ..... ............................ ........... ..... ...... 17 Universal Joints, Propeller Shall ........ .......... .... ........................... .... ............ 1 0

Valve System ....................... . ...... ........................... ....... ................................ 4 Voltage Regu lator .... ....... ....... .................. .............. .... .......... ..................... .. 16

Water f>ump ....................................................................... _ ..................... ... 5 Weights ..................................................................................... ........ 25 . 26 Wheel Alignmetll ................................................................................ - ...... 15 Wh9elbaSe .... ...... ........................ ................................................................ 20 llllheels a 1iA1& .................................................. - ........... ............................ 13 Wheel Spindle ..... ............ ........................................ ........... .... .......... .. ......... 14 Widths - Car and Body .......................................... .......................... ....... .... 20 Wlndshie lcl ..................... ...... .................. ......................... , .................. .......... 18 Windshie lcl Wiper and Washer ................................................................... 15

Page34

Passenger Car 1986

Documents

Transcript of Passenger Car 1986