PARWELD LIMITED Bewdley Business Park, Long Bank, Bewdley, … · PARWELD LIMITED Bewdley Business...
Transcript of PARWELD LIMITED Bewdley Business Park, Long Bank, Bewdley, … · PARWELD LIMITED Bewdley Business...
PARWELD LIMITED Bewdley Business Park, Long Bank, Bewdley, Worcestershire DY12 2TZ
T +44 1299 266 800 F +44 1299 266 900
UK SALES 01299 269 500 EXPORT SALES +44 1299 269 507
E [email protected] www.parweld.com
Increased Productivity With arguably the world’s most productive welding torch.
PrOdUcT cAtALoGuE
Sales: +44 (0) 1299 266800E-Mail: [email protected]
WhaT Makes XP8 Different?
80% DUTY CYCLEIn recent years guidelines laid down by the european standard en60974-7 have served to harmonise global understanding of MIG welding torch performance. The ratings of european torches were traditionally based on a 5-minute cycle where a 60% duty cycle was defined as 3 minutes weld time & 2 minutes downtime. american torches were traditionally rated over a 10-minute cycle where a 60% duty cycle represents 6 minutes weld time & 4 minutes downtime. The new standards have resulted in the duty cycles of many european torch brands being downgraded in performance due to the extended welding period.The XP8 air cooled torch models are rated at 80% & will weld continuously for 8 minutes at their given ratings. The XP8 water-cooled torches are rated at 100% duty cycle & will weld continuously.
SUPERIOR ERgOnOMICSThe neck & handle geometries have been designed to give a neutral wrist position when welding to reduce the risk of rsI (repetitive strain Injury). The handle design is the most compact available & the handle grips are designed to prevent the torch slipping in the welders hand allowing him to relax his grip, further reducing strain.The knuckle joint & tapered support improve freedom of movement & give progressive support to the power cable allowing it to form a smooth curve into the handle & maximise wire feed. In order to provide a more precise method of selecting the correct torch required for a given application & process we now quote the maximum rated output in kilowatts for each XP8 torch, an industry first.
XP8 IS RATED In KILOWATTAgE – WhY?amperages & duty cycle s alone are arbitrary measures of a torches capability.For a more accurate appreciation wire type, gas type, flow rate & open circuit voltage must all be taken into consideration.The XP8 is rated in amps as a guideline but the kilowattage requirement of a given application provides a far more accurate method for calculating torch selection.kilowattage represents the total power rating required & is calculated as follows:
Welding amps x Welding Volts = kW
1000
(amps x Volts = Watts , 1000 Watts = 1 kW).
hOW DO I SELECT A TORCh USIng KILOWATTAgE?If a torch is required to weld at 300 amps with a welding voltage of 34 volts the kilowattage is 10.2 kW. I.e.
Welding amps 300 x Welding Volts 34 = 10.2 kW1000
Ideal torches for the applications would therefore be the XP8 350a for an air cooled 80% duty requirement or the XP8 450W for a water cooled 100% application.
The XP8 is a fresh approach. It has been designed around today’s production environment, modern welding techniques and equipment. The XP8 sets new standards in design, innovation and performance.
XP8 Features and BenefitsTh
e W
orl
d’s
Mo
sT P
rod
uc
Tiv
e W
eld
ing
To
rch
MixEd GAs (80/20)
Model Amps kW Duty Cycle
XP8-200a 200 6.0 80%
XP8-300a 300 8.7 80%
XP8-350a 350 10.5 80%
XP8-400a 400 12.0 80%
XP8-320W 320 9.6 100%
XP8-450W 450 15.8 100% PATEnTED gAS FLOW TEChnOLOgYThe shielding gas in the XP8 is put to work to improve the cooling effect of the torch neck and front end consumable parts.On entering the rear of the neck the gas is separated from the conduit to flow directly over heat sink fins contained in the copper conductor, before emerging at the base of the tip adaptor to directly force cool the contact tips.
COnTACT TIPS LIFE COMPARATIvE DATA
Welding Hours @ rated duty and power
Torc
h M
od
els
0 10 20 30
Tregaskiss® 500
MB 501
XP8 350
Bernard® Q500
Tweco® 5
Welding hours @ rated duty and power EXTEnDED COnSUMABLE LIFE EXPECTAnCYsuperior materials combined with stringent design and performance criteria have resulted in an entire range of consumables with dramatically improved life expectancy.
Sales: +44 (0) 1299 266800E-Mail: [email protected] 3
Table to show the affect on XP8 performance when using alternate wire types
STEEL WIRE (80/20) ALUMInIUM WIRE (100% Ar) CORED WIRE (18/20)
MODEL CYCLE AMPS KW AMPS kW AMPS KW
XP8-200a 80% 200 6.0 200 6.0 200 6.2
XP8-300a 80% 300 8.7 280 8.4 300 9.3
XP8-350a 80% 350 10.5 300 9.0 350 10.5
XP8-400a 80% 400 12.0 300 9.0 400 12.0
XP8-320W 100% 320 9.6 320 9.6 320 9.6
XP8-450W 100% 450 15.8 450 15.8 450 15.8
WIll The WIre TyPe aFFecT The PerFOrMance OF The TOrch?Basically yes, but not to the same extent as changes in any other variables.
Table to show the affect on XP8 performance when using pulse welding
MIXED gAS (95/5)
MODEL AMPS kW CYCLE
XP8-200a 200 6.0 80%
XP8-300a 260 9.0 80%
XP8-350a 260 9.0 80%
XP8-400a 260 9.0 80%
XP8-320W 320 9.6 100%
XP8-450W 450 15.8 100%
WIll a PUlse WeldInG PrOcess aFFecT The PerFOrMance OF The TOrch?The affect of pulse welding on all air cooled torches is dramatic.In the XP8 the effect is similar for all wire types when using a pulse process.
noTe: all ratings are based on a nominal gas flow of 18lpm. a lower gas flow will result in an increase in working temperature but it will not have any adverse affect as long as the gas flow is within the accepted limits for the welding amperage.
Table to show the affect on XP8 performance when using alternate gas types
MIXED gAS (80/20) MIXED gAS (95/5) 100% CO2
MODEL AMPS KW AMPS kW AMPS KW
XP8-200a 200 6.0 200 6.0 200 7.8
XP8-300a 300 8.7 280 8.4 375 11.7
XP8-350a 350 10.5 300 9.0 425 14.9
XP8-400a 400 12.0 300 9.0 480 17.2
XP8-320W 320 9.6 320 9.6 320 9.6
XP8-450W 450 15.8 450 15.8 450 15.8
WIll The Gas I Use aFFecT The PerFOrMance OF The TOrch?The simple answer is yes. The use of different gas types can have a marked effect on the performance of air cooled torches. Generally the higher the content of cO2 in the shielding gas the better the performance of the MIG torch.
Torch selector table for mild steel wires (80/20) argon/cO2 shielding gas.
MIXED gAS (80/20)
MODEL AMPS kW DUTY CYCLE MAX WIRE SIZE
XP8-200a 200 6.0 80% .045"/1.2mm
XP8-300a 300 8.7 80% .045"/1.2mm
XP8-350a 350 10.5 80% 1/16"/1.6mm
XP8-400a 400 12.0 80% 3/32"/2.4mm
XP8-320W 320 9.6 100% 1/16"/1.6mm
XP8-450W 450 15.8 100% 3/32"/2.4mm
Torch Weight
WEIghT
MODEL Kg LB
XP8-200a 1.4 3.1
XP8-300a 1.6 3.5
XP8-350a 1.9 4.2
XP8-400a 2.0 4.4
XP8-320W 1.4 3.1
XP8-450W 1.5 3.3
XP8 Features and BenefitsTh
e Wo
rld’s M
osT Pro
du
cTiv
e Weld
ing
Torc
h
Sales: +44 (0) 1299 266800E-Mail: [email protected]
SWAn nECKS• Overmoulded necks prevent reflected heat transfer passing through the neck. • Shorting of the neck to the work piece is now impossible.• Necks are more impact resistant than metal clad necks
• Lightweight, durable and robust
COnTACT TIPS• Exceptional Service Life•Manufactured from a high grade chrome Zirconium copper alloy• Extra length• Dual contact points• Force cooling
ShAKE PROOF WAShER (Not
Illustrated)• Offers extra security to
ensure cables do not work lose due to repetitive twisting and rotating of the torch front end.
InnOvATIvE hAnDLE DESIgn - nO MORE TOOLS• Screwless design solutions• Modular fit concept• Significantly reduces RSI• Integrated dual grips with additional ribs for a relaxed grip
• Offers the ultimate in comfort and ease of
handling
nOZZLES• Self Insulated• Ensures cooler running necks• High specification resin and
sleeve assembly• Push on
hAngER hOOKS• Easy to Store - less prone to damage
• Encourages efficient and tidy workspace
TRIggER • Encapsulated trigger
extends service life
TRIggER gUARD• Further reduces the risk of
unintentional activation
SIDE vEnTS• Ensures ultimate cooling
ThUMB REST•Offers additional comfort
hYDROFLEX™ CABLE SYSTEMS • Liquid cooled cable systems use high temperature resistant
rubber cables which when combined with unique cable end geometries ensure leak free terminations
• XP8 hydroflex™ cable systems outperform all PVc alternatives• Air cooled cable assemblies offer outstanding flexibility and
the highest heat and abrasion resistance of any known cable• Cable end and crimp systems ensure maximum conductivity.
The outer jacket is constructed from cross linked polymers providing a tear proof jacket and a burn threshold of 375°c
CRIMP SYSTEMS• Cable termination design and crimp system guarantee sealing
hIgh FLEX BALL JOInT SYSTEM• Improved Manoeuvrability• Small movements of the handle and neck are possible independent of the cable assemblyCABLE SUPPORTS• Improved Wire Feed• The perfect balance of freedom of movement and
progressive support to the power cable is achieved.
MAChInE EnD SYSTEMS• Extra length cable support systems• Smooth and consistent wire feed• Simple snap fits
gUn PLUg BODIES• Spring loaded pins• Guaranteed gas seals
XP8
g2
Feat
ures
and
Ben
efits
XP8 g2 Features and Benefits
Sales: +44 (0) 1299 266800E-Mail: [email protected] 5
FLEXIBLE• Wide range of necks available in various combinations of length and bend angle.• Both Air and Water cooled models available.
FULLY ROTATIng nECK
• For multi-positional welding in those limited access, difficult to reach locations.
• Offering better welder comfort and reducing fatigue.
XP8 FROnT EnD AnD nECK DESIgn • Offers the same robust features with improved performance and service life as standard XP8.
LInERS• Quick and easy change
over with dedicated neck liners
XP8 roTATing necK Features and BenefitsX
P8 roTA
Ting
nec
KFeatures and B
enefitsRE-EngInEERED COnDUCTOR DESIgn For improved gas flow, strength and toughness.
Sales: +44 (0) 1299 266800E-Mail: [email protected]
hAnDLE• Integrated high level grip, robust and balanced ergonomic handle design.
• recessed and guarded trigger
DRIvE COnTROL MODULE• Torch supplied with motor
drive control module for mounting in push feed unit which accepts ac or dc voltage 18 –to- 42V and features a push motor start/stop sensing control.
• Two drive configuration options; fixed feed rate with trimming on the control module or remote feed rate adjustment via a torch handle mounted control
• Three control mounting options; machine local mounted, separate portable
unit or cable integrated.
KnUCKLE JOInT• Full flexibility from handle
knuckle joint allowing all angles of movement without the resistance of an extended cable support
RE-EngInEERED COnDUCTOR• Design for improved gas flow, strength and toughness.
REMOTE FEED RATE COnTROL• Option torch mounted variable wire feed rate control
XP8• XP8 front end and neck
design offer the robust features, improved performance and service life as standard XP8.
WIRE FEED SYSTEM• Easy access hinged cover• Range of drive rolls• Adjustable feed roll pressure
nECKS• Wide range of necks
available in various combinations of length and bend angle. Both air and Water cooled models available.
• Fully rotating neck for multi-positional welding in those limited access, difficult to reach location. Offering better welder comfort and reducing fatigue.
DRIvE SYSTEM• Modern, european
manufactured dc motor;small, lighter, more powerful output
• constant speed output - constant wire feed and tension
• 27m / 88ft per minute maximum wire feed rate capability
LInERS• Quick and easy change over with dedicated neck liners
TORCh PACKAgES• 350a air and 450a Water
cooled models available.
XP8
Pu
sh P
ull
Feat
ures
and
Ben
efits
XP8 Push Pull Features and Benefits
Sales: +44 (0) 1299 266800E-Mail: [email protected] 7
PACKAgE STOCK CODE BUILDIngexample torch package stock code is given below for XP8 350a neck, 3.5” long x 0° straight, 8m cable and euro machine
connection, remote speed control with machine mounted driver.
1. nECK MODEL
4. CABLE LEngTh
5. MAChInE COnnECTIOn6. DRIvE COnTROL
XP35 P 35 00 - 80 E R
1. nECK MODEL
Stock Code Model
XP35 XP8 350a
XP45 XP8 450W
4. CABLE LEngTh
Stock Code Length
60 6m / 20ft
80 8m / 26ft
10 10m / 33ft
5. MAChInE COnnECTIOn
Stock Code Description
e euro
2. nECK LEngTh
Stock Code Length
35 3.5” / 89mm
40 4” / 102mm
45 4.5” / 114mm
60 6” / 153mm
90 9” / 229mm
12 12” / 305mm
18 18” / 457mm
3. nECK AngLE
Stock Code Angle
00 0° straight
05 5°
30 30°
45 45°
60 60°
6. DRIvE COnTROL
Stock Code Description
local speed control Machine Mounted driver Module
r remote speed control c/w Machine Mounted driver Module
s local speed control separate driver Unit
c remote speed control c/w cable Integrated driver Module
3. nECK AngLE
2. nECK LEngTh
TORCh TYPE
Stock Code Type
P Push-Pull
PACKAgE STOCK CODE BUILDIngexample of a torch package stock code is given below for a XP8 350a rotating neck, 12” long x 45° Bend, 4 metre long cable and euro machine
connection.
XP35 R 2 4 - 40 E
1. nECK MODEL
Stock Code Model
XP35 XP8 350a
XP40 XP8 400a
XP45 XP8 450W
4. CABLE LEngTh
Stock Code Length
30 3m/10ft
40 4m/13ft
50 5m/16ft
5. MAChInE COnnECTIOn
Stock Code Description
e XP8 euro
STAnDARD BUILD: Torch packages are supplied fitted with a 1.2mm wire contact Tips and liners with a 5/8”/16mm bore conical nozzle. nECK SELECTIOn: not every variant of neck angle is available for some lengths. For further information see XP8 rotating neck data sheet
2. nECK LEngTh
4. CABLE LEngTh
5. MAChInE COnnECTIOn
2. nECK LEngTh
Stock Code Length
4 4” / 102mm
5 4.5” / 114mm
6 6” / 153mm
9 9” / 229mm
2 12” / 305mm
8 18” / 457mm
3. nECK AngLE
Stock Code Angle
0 0° straight
5 5°
3 30°
4 45°
6 60°
1. nECK MODEL
3. nECK AngLE
TORCh TYPE
Stock Code Type
r rotating
XP8 Push Pull Ordering Guide
XP8 roTATing necK Ordering Guide
XP8
Torch Packages Ordering G
uidesstandard Build: Torch packages are supplied fitted with a 1.2mm wire contact tip and liner with a 5/8”/16mm bore conical nozzle.
neck selection: not every variant of neck angle is available for some lengths. For further information see XP8 rotating neck range data sheet
Sales: +44 (0) 1299 266800E-Mail: [email protected]
XP8 nozzlesX
P8 c
on
suM
AB
les
STOCK CODE DESCRIPTIOn TIP RECESS BORE MODEL
XP2002-10 Tapered nozzle Flush 10mm/3/8" XP200a-320W
STOCK CODE DESCRIPTIOn TIP RECESS BORE MODEL
XP2002-16l conical nozzle 6.5mm/1/4" 16mm/5/8" XP200a-320W
XP2002-19l cylindrical nozzle 6.5mm/1/4" 19mm/3/4" XP200a-320W
STOCK CODE DESCRIPTIOn TIP RECESS BORE MODEL
XP2002-13 Tapered nozzle 2.4mm/3/32" 13mm/1/2" XP200a-320W
XP2002-16 conical nozzle 2.4mm/3/32" 16mm/5/8" XP200a-320W
XP2002-19 cylindrical nozzle 2.4mm/3/32" 19mm/3/4" XP200a-320W
STOCK CODE DESCRIPTIOn TIP RECESS BORE MODEL
XP3002-16l conical nozzle 6.5mm/1/4" 16mm/5/8" XP300a-450W
XP3002-19l cylindrical nozzle 6.5mm/1/4" 19mm/3/4" XP300a-450W
STOCK CODE DESCRIPTIOn TIP RECESS BORE MODEL
XP3002-13 Tapered nozzle 3mm/1/8" 13mm/1/2" XP300a-450W
XP3002-16 conical nozzle 3mm/1/8" 16mm/5/8" XP300a-450W
XP3002-19 cylindrical nozzle 3mm/1/8" 19mm/3/4" XP300a-450W
STOCK CODE DESCRIPTIOn TIP RECESS BORE MODEL
XP2002-07T long Tapered nozzle 3mm/1/8" 7mm/9/32" XP200a-320W
XP2002-10T long Tapered nozzle 3mm/1/8" 10mm/3/8" XP200a-320W
STOCK CODE DESCRIPTIOn TIP RECESS BORE MODEL
XP3002-10T long Tapered nozzle 3mm/1/8" 10mm/3/8" XP8300a-450W roll Markingall Parweld consumables are roll marked to
enable you to identify genuine Parweld product.
Sales: +44 (0) 1299 266800E-Mail: [email protected] 9
roll Markingall Parweld consumables are roll marked to enable you to
identify genuine Parweld product.
XP8 contact TipsX
P8 co
nsu
MA
Bles
contact TipsSTOCK CODE WIRE SIZE MATERIAL
XP2003-06 0.6mm/.023" cucrZr
XP2003-08 0.8mm/.030" cucrZr
XP2003-09 0.9mm/.035" cucrZr
XP2003-10 1.0mm/.040" cucrZr
XP2003-12 1.2mm/.045" cucrZr
XP2003-13 1.3mm/.052" cucrZr
XP2003-14 1.4mm/.055" cucrZr
XP2003-10a* 1.0mm/.040" cucrZr al
XP2003-12a* 1.2mm/.045" cucrZr al
MOdel - XP200a-320W
contact TipsSTOCK CODE WIRE SIZE MATERIAL
XP3003-08 0.8mm/.030" cucrZr
XP3003-09 0.9mm/.035" cucrZr
XP3003-10 1.0mm/.040" cucrZr
XP3003-12 1.2mm/.045" cucrZr
XP3003-13 1.3mm/.052" cucrZr
XP3003-14 1.4mm/.055" cucrZr
XP3003-16 1.6mm/1/16" cucrZr
XP3003-18 1.8mm/.071" cucrZr
XP3003-20 2.0mm/5/64" cucrZr
XP3003-24 2.4mm/3/32" cucrZr
XP3003-10a* 1.0mm/.040" cucrZr al
XP3003-12a* 1.2mm/.045" cucrZr al
MOdel - XP300a-450W
Tapered contact TipsSTOCK CODE WIRE SIZE MATERIAL
XP2003-06T 0.6mm/.023" cucrZr
XP2003-08T 0.8mm/.030" cucrZr
XP2003-09T 0.9mm/.035" cucrZr
XP2003-10T 1.0mm/.040" cucrZr
XP2003-12T 1.2mm/.045" cucrZr
XP2003-13T 1.3mm/.052" cucrZr
XP2003-14T 1.4mm/.055" cucrZr
MOdel - XP200a-320W
Tapered contact TipsSTOCK CODE WIRE SIZE MATERIAL
XP3003-08T 0.8mm/.030" cucrZr
XP3003-09T 0.9mm/.035" cucrZr
XP3003-10T 1.0mm/.040" cucrZr
XP3003-12T 1.2mm/.045" cucrZr
XP3003-13T 1.3mm/.052" cucrZr
XP3003-14T 1.4mm/.055" cucrZr
XP3003-16T 1.6mm/1/16" cucrZr
XP3003-18T 1.8mm/.071" cucrZr
XP3003-20T 2.0mm/5/64" cucrZr
XP3003-24T 2.4mm/3/32" cucrZr
MOdel - XP300a-450W
STOCK CODE DESCRIPTIOn hEAD MODEL
XP2004B Plastic diffuser M8 XP200a-320w
XP2004cceramic diffuser
M8 XP200a-320W
STOCK CODE DESCRIPTIOn hEAD MODEL
XP3004B Moulded diffuser With ceramic Insert
M10 XP350a-450W
STOCK CODE DESCRIPTIOn hEAD MODEL
XP3004c ceramic diffuser M10 XP350a-450W
XP8 diffusers
all contact tips listed are in material cucrZr*contact Tip al
Sales: +44 (0) 1299 266800E-Mail: [email protected]
XP8 head AssembliesX
P8 c
on
suM
AB
les
head assemblySTOCK CODE TIP ThREAD MODEL
XP2005 M8 XP8200a-320W
head assemblySTOCK CODE TIP ThREAD MODEL
XP3005 M10 XP8200a-320W
Tapered Tip head assemblySTOCK CODE TIP ThREAD MODEL
XP2005T M8 XP8200a-320W
head assemblySTOCK CODE TIP ThREAD MODEL
XP3505 M10 XP8350a-450W
Tapered Tip head assemblySTOCK CODE TIP ThREAD MODEL
XP3505T M10 XP8350a-450W
A hard Wire roll setsSTOCK CODE DESCRIPTIOn WIRE SIZE COLOUR WIRES
a PP08rs Plain V Groove 0.8mm/0.030” White □ Fe, ss
PP09rs Plain V Groove 0.9mm/0.035” Green ■ Fe, ss
PP10rs Plain V Groove 1.0mm/0.040” Blue ■ Fe, ss
PP12rs Plain V Groove 1.2mm/0.045” red ■ Fe, ss
PP14rs Plain V Groove 1.4mm/0.055” Black ■ Fe, ss
PP16rs Plain V Groove 1.6mm/0.062” yellow ■ Fe, ss
Feed & Pressure roll sets - XP8 Push Pull
B soft Wire roll setsSTOCK CODE DESCRIPTIOn WIRE SIZE COLOUR WIRES
B PP08ars Plain U Groove 0.8mm/0.030” White □ al
PP09ars Plain U Groove 0.9mm/0.035” Green ■ al
PP10ars Plain U Groove 1.0mm/0.040” Blue ■ al
PP12ars Plain U Groove 1.2mm/0.045” red ■ al
PP14ars Plain U Groove 1.4mm/0.055” Black ■ al
PP16ars Plain U Groove 1.6mm/0.062” yellow ■ al
Sales: +44 (0) 1299 266800E-Mail: [email protected] 11
A B
XP8 liners selector chart
Stock Code Description Length Wire Size Application
MODEL
XP
200A
XP
300A
XP
350A
XP4
00A
XP
320W
XP4
50W
A
XP2024-09-30
STEEL LInERS
3M/10FT.023"-.035" / 0.6-0.9mm
sTeel WIres
m m M M M M
XP2024-09-40 4M/13FT m m M M M M
XP2024-09-50 5M/16FT m m M M M M
XP2024-12-30 3M/10FT040"-.045" / 1.0-1.2mm
m m M M m M
XP2024-12-40 4M/13FT m m M M m M
XP2024-12-50 5M/16FT m m M M m M
XP2024-16-30 3M/10FT.045"-.063" / 1.2-1.6mm
M M M M m M
XP2024-16-40 4M/13FT M M M M m M
XP2024-16-50 5M/16FT M M M M m M
B
XP2024Pc-12-30POLYAMIDE-COPPER LInERS
3M/10FT
.030"-.045" / 0.8-1.2mm
sOFT WIresm m m M m m
XP2024Pc-12-40 4M/13FT m m m M m m
XP2024Pc-12-50 5M/16FT m m m M m m
XP2024Ps-12-30POLYAMIDE-STEEL LInERS
3M/10FThard WIres
m m m M m m
XP2024Ps-12-40 4M/13FT m m m M m m
XP2024Ps-12-50 5M/16FT m m m M m m
A
XP3524-12-30
STEEL LInERS
3M/10FT040"-.045" / 1.0-1.2mm
sTeel WIres
m m M m
XP3524-12-40 4M/13FT m m M m
XP3524-12-50 5M/16FT m m M m
XP3524-16-30 3M/10FT
.045"-.063" / 1.2-1.6mm
m m M m
XP3524-16-40 4M/13FT m m M m
XP3524-16-50 5M/16FT m m M
B
XP3524Pc-16-30POLYAMIDE-COPPER LInERS
3M/10FTsOFT WIres
m M m m
XP3524Pc-16-40 4M/13FT m M m m
XP3524Pc-16-50 5M/16FT m M m m
XP3524Ps-16-30POLYAMIDE-STEEL LInERS
3M/10FThard WIres
m M m m
XP3524Ps-16-40 4M/13FT m M m m
XP3524Ps-16-50 5M/16FT m M m m
AXP4024-24-30
STEEL LInERS3M/10FT
.080"-.095" / 2.0-2.4mm sTeel WIresM m M m
XP4024-24-40 4M/13FT M m M m
XP4024-24-50 5M/16FT M m M m
B
XP4024Pc-20-30POLYAMIDE-COPPER LInERS
3M/10FT
.063/.080" / 1.6-2.0mm
sOFT WIresM m M m
XP4024Pc-20-40 4M/13FT M m M m
XP4024Pc-20-50 5M/16FT M m M m
XP4024Ps-20-30POLYAMIDE-STEEL LInERS
3M/10FThard WIres
M m M m
XP4024Ps-20-40 4M/13FT M m M m
XP4024Ps-20-50 5M/16FT M m M m
XP8 c
on
suM
AB
les
liner selector chart - XP8 Push Pull
A
Torch liners
STOCK CODE DESCRIPTIOn LEngTh WIRE SIZE
MODEL
XP
350A
XP
450W
a PP1536-80 Teflon liner 8.0 mt 0.6-0.9mm/0.025”-0.035” m m
PP2513-80 Teflon liner 8.0 mt 1.0-1.2mm/0.040”-0.045” m m
PP3626-80 Teflon liner 8.0 mt 1.2-1.6mm/0.045”-0.063” m
colour code:0.6-0.9mm - Wire Blue m1.0-1.2mm - Wire red m1.2-1.6mm - Wire yellow m2.0-2.4mm - Wire Green m
Sales: +44 (0) 1299 266800E-Mail: [email protected]
A
B
1
2
3 4
4
5
6
7
8
9
10
11
1213
15 1416
1719
C
D
620212223
E18
note: all ratings are based on a nominal gas flow of 18lpm. a lower gas flow will result in an increase in working temperature but it will not have any adverse affect as long as the gas flow is within the accepted limits for the welding amperage.
Table to show the affect on XP8 performance when using alternate gas types:
MIXED gAS (80/20) MIXED gAS (95/5) 100% CO2
Model amps kW amps kW amps kW
XP8-200a 200 6.0 200 6.0 260 7.8
amperages and duty cycles alone are arbitrary measures of a torches capability.For a more accurate appreciation wire type, gas type, flow rate and open circuit voltage must all be taken into consideration.
The XP8 is rated in amps as a guideline but the kilowattage requirement of a given application provides a far more accurate method for calculating torch selection.kilowattage represents the total power rating required and is calculated as follows:
(amps x Volts = Watts , 1000 Watts = 1 kW)
Welding amps x Welding Volts = kW
1000
selecTInG The cOrrecT XP8 TOrch
XP8 200A200a, 6kW, MIXed Gas (80/20) @ 80% dUTy cycle, en60974-7 .023”- .045”/0.6MM TO 1.2MM WIres
air cooled Mig Welding TorchX
P8 T
orc
hes
Sales: +44 (0) 1299 266800E-Mail: [email protected] 13
roll Markingall Parweld consumables are roll marked to enable you to identify genuine Parweld product.
XP8 To
rch
esModel
STOCK CODE DESCRIPTIOn
XP200a-30e Welding Torch Package c/w euro Fitting x 3m
XP200a-40e Welding Torch Package c/w euro Fitting x 4m
XP200a-50e Welding Torch Package c/w euro Fitting x 5m
nozzlesSTOCK CODE DESCRIPTIOn
a XP2002-10 Tapered nozzle 3/8"/10mm
XP2002-13 Tapered nozzle 1/2"/13mm
XP2002-16* conical nozzle 5/8"/16mm
XP2002-16l conical nozzle 5/8"/16mm extended
XP2002-19 cylindrical nozzle 3/4"/19mm
XP2002-19l cylindrical nozzle 3/4"/19mm extended
B XP2002-07T long Tapered nozzle 3mm/1/8" 7mm/9/32"
XP2002-10T long Tapered nozzle 3mm/1/8" 10mm/3/8"
contact TipsSTOCK CODE SIZE
COnTACT TIPS, M8, CuCrZr
c XP2003-06 .023"/0.6mm
XP2003-08 .030"/0.8mm
XP2003-09 .035"/0.9mm
XP2003-10* .040"/1.0mm
XP2003-10a .040"/1.0mm, al
XP2003-12 .045"/1.2mm
XP2003-12a .045"/1.2mm, al
TAPERED COnTACT TIPS, CuCrZr
d XP2003-06T 0.6mm/.023"
XP2003-08T 0.8mm/.030"
XP2003-09T 0.9mm/.035"
XP2003-10T 1.0mm/.040"
XP2003-12T 1.2mm/.045"
linersSTOCK CODE SIZE
STEEL LInERS
e XP2024-09-30 .023-.035"/0.6-0.9mm x 3m/10ft
XP2024-09-40 .023-.035"/0.6-0.9mm x 4m/13ft
XP2024-09-50 .023-.035"/0.6-0.9mm x 5m/16ft
XP2024-12-30* .040-.045"/1.0-1.2mm x 3m/10ft
XP2024-12-40* .040-.045"/1.0-1.2mm x 4m/13ft
XP2024-12-50* .040-.045"/1.0-1.2mm x 5m/16ft
POLY-COPPER LInERS
nI XP2024Pc-12-30 .030-.045"/0.8-1.2mm x 3m/10ft
XP2024Pc-12-40 .030-.045"/0.8-1.2mm x 4m/13ft
XP2024Pc-12-50 .030-.045"/0.8-1.2mm x 5m/16ft
linersSTOCK CODE SIZE
POLY-STEEL LInERS
XP2024Ps-12-30 .030-.045"/0.8-1.2mm x 3m/10ft
XP2024Ps-12-40 .030-.045"/0.8-1.2mm x 4m/13ft
XP2024Ps-12-50 .030-.045"/0.8-1.2mm x 5m/16ft
components * denotes standard Build
STOCK CODE DESCRIPTIOn
1 XP2004B* diffuser-Plastic-M8 head
nI XP2004c diffuser-ceramic-M8 head
2 XP2005* head assembly-M8 Tips
3 XP2005T head assembly-M8 Tapered Tips
nI XP2006B heat shield-Moulded-M8 head
4 XP2006a* aluminium heat shield-M8 head
5 XP2001 swan neck
6 XP2016 lock nut M12
7 XP2088 cable support
8 XP3009 handle lock nut
9 XP2010-30 hyperflex™ cable assembly x 3m/10ft
XP2010-40 hyperflex™ cable assembly x 4m/13ft
XP2010-50 hyperflex™ cable assembly x 5m/16ft
10 XP2011 cable Terminal Female
11 XP2112 handle kit c/w lock nut and support
12 XP2013 hanger hook
13 XP2014 Trigger assembly
14 XP2015 cable Terminal Male
15 XP2017 cable support
16 XP2018 air cooled Gun Plug housing c/w nut
17 XP2019 Gun Plug screw
18 XP2020 Gun Plug nut
19 spring Pin 2 spring Pin assembly
20 XP2022 Gun Plug Body c/w spring Pins
21 XP2023 euro Body ‘O’ ring
22 XP2025 liners nipple ‘O’ rings
23 XP2026 liners retaining nut
ParWeld XP8 TOrches enaBle yOU TO rePaIr The neck end OF The POWer caBle, Please Use sTOck cOde: XP2042: 200a
POWer caBle rePaIr kIT
nI - nOT IllUsTraTed
Sales: +44 (0) 1299 266800E-Mail: [email protected]
B
A
C
2
1 F
4
35
7
66
8
9
10
11
12
13
14
15 16
18 1719
2022
E
D
9
23242526
g21
note: all ratings are based on a nominal gas flow of 18lpm. a lower gas flow will result in an increase in working temperature but it will not have any adverse affect as long as the gas flow is within the accepted limits for the welding amperage.
Table to show the affect on XP8 performance when using alternate gas types:
MIXED gAS (80/20) MIXED gAS (95/5) 100% CO2
Model amps kW amps kW amps kW
XP8-300a 300 8.7 280 8.4 375 11.7
amperages and duty cycles alone are arbitrary measures of a torches capability.For a more accurate appreciation wire type, gas type, flow rate and open circuit voltage must all be taken into consideration.
The XP8 is rated in amps as a guideline but the kilowattage requirement of a given application provides a far more accurate method for calculating torch selection.kilowattage represents the total power rating required and is calculated as follows:
(amps x Volts = Watts , 1000 Watts = 1 kW)
Welding amps x Welding Volts = kW
1000
selecTInG The cOrrecT XP8 TOrch
XP8 300A300a, 8.7kW, MIXed Gas (80/20) @ 80% dUTy cycle, en60974 -7 .030”- .045”/0.8MM TO 1.2MM WIres
air cooled Mig Welding TorchX
P8 T
orc
hes
ModelSTOCK CODE DESCRIPTIOn
XP300a-30e Welding Torch Package c/w euro Fitting x 3m
XP300a-40e Welding Torch Package c/w euro Fitting x 4m
XP300a-50e Welding Torch Package c/w euro Fitting x 5m
Sales: +44 (0) 1299 266800E-Mail: [email protected] 15
roll Markingall Parweld consumables are roll marked to enable you to identify genuine Parweld product.
XP8 To
rch
esnozzles
STOCK CODE DESCRIPTIOn
a XP2002-10 Tapered nozzle 3/8"/10mm
XP2002-13 Tapered nozzle 1/2"/13mm
XP2002-16* conical nozzle 5/8"/16mm
XP2002-16l conical nozzle 5/8"/16mm extended
XP2002-19 cylindrical nozzle 3/4"/19mm
XP2002-19l cylindrical nozzle 3/4"/19mm extended
B XP3002-13 Tapered nozzle 1/2"/13mm
XP3002-16 conical nozzle 5/8"/16mm
XP3002-16l conical nozzle 5/8"/16mm extended
XP3002-19 cylindrical nozzle 3/4"/19mm
XP3002-19l cylindrical nozzle 3/4"/19mm extended
c XP2002-07T long Tapered nozzle 3mm/1/8" 7mm/9/32"
XP2002-10T long Tapered nozzle 3mm/1/8" 10mm/3/8"
contact Tips STOCK CODE SIZE
COnTACT TIPS, M8, CuCrZr
d XP2003-08 .030"/0.8mm
XP2003-09 .035"/0.9mm
XP2003-10 .040"/1.0mm
XP2003-10a .040"/1.0mm, al
XP2003-12* .045"/1.2mm
XP2003-12a .045"/1.2mm, al
COnTACT TIPS, M10, CuCrZr
e XP3003-08 .030"/0.8mm
XP3003-09 .035"/0.9mm
XP3003-10 .040"/1.0mm
XP3003-10a .040"/1.0mm al
XP3003-12 .045"/1.2mm
XP3003-12a .045"/1.2mm al
TAPERED COnTACT TIPS, CuCrZr
F XP2003-06T 0.6mm/.023"
XP2003-08T 0.8mm/.030"
XP2003-09T 0.9mm/.035"
XP2003-10T 1.0mm/.040"
XP2003-12T 1.2mm/.045"
linersSTOCK CODE SIZE
STEEL LInERS
G XP2024-09-30 .023-.035"/0.6-0.9mm x 3m/10ft
XP2024-09-40 .023-.035"/0.6-0.9mm x 4m/13ft
XP2024-09-50 .023-.035"/0.6-0.9mm x 5m/16ft
XP2024-12-30* .040-.045"/1.0-1.2mm x 3m/10ft
XP2024-12-40* .040-.045"/1.0-1.2mm x 4m/13ft
XP2024-12-50* .040-.045"/1.0-1.2mm x 5m/16ft
linersSTOCK CODE SIZE
POLY-COPPER LInERS
nI XP2024Pc-12-30 .030-.045"/0.8-1.2mm x 3m/10ft
XP2024Pc-12-40 .030-.045"/0.8-1.2mm x 4m/13ft
XP2024Pc-12-50 .030-.045"/0.8-1.2mm x 5m/16ft
POLY-STEEL LInERS
XP2024Ps-12-30 .030-.045"/0.8-1.2mm x 3m/10ft
XP2024Ps-12-40 .030-.045"/0.8-1.2mm x 4m/13ft
XP2024Ps-12-50 .030-.045"/0.8-1.2mm x 5m/16ft
components * denotes standard Build
STOCK CODE DESCRIPTIOn
1 XP2004B* diffuser-Plastic-M8 head
nI XP2004c diffuser-ceramic-M8 head
2 XP3004B diffuser-Moulded c/w ceramic Insert-M10 head
nI XP3004c diffuser-ceramic-M10 head
3 XP2005* head assembly-M8 Tips
4 XP3005 head assembly-M10 Tips
5 XP2005T head assembly-M8 Tapered Tips
6 XP2006a* aluminium heat shield-M8 head
nI XP2006B heat shield-Moulded-M8 head
7 XP3006a aluminium heat shield-M10 head
nI XP3006B heat shield-Moulded-M10 head
8 XP3001 swan neck
9 XP2016 lock nut M12
10 XP3088 cable support
11 XP3009 handle lock nut
12 XP3010-30 hyperflex™ cable assembly x 3m/10ft
XP3010-40 hyperflex™ cable assembly x 4m/13ft
XP3010-50 hyperflex™ cable assembly x 5m/16ft
13 XP2011 cable Terminal Female
14 XP2112 handle kit c/w lock nut and support
15 XP2013 hanger hook
16 XP2014 Trigger assembly
17 XP2015 cable Terminal Male
18 XP3017 cable support
19 XP2018 air cooled Gun Plug housing c/w nut
20 XP2019 Gun Plug screw
21 XP2020 Gun Plug nut
22 spring Pin 2 spring Pin assembly
23 XP2022 Gun Plug Body c/w spring Pins
24 XP2023 euro Body ‘O’ ring
25 XP2025 liners nipple ‘O’ rings
26 XP2026 liners retaining nut
ParWeld XP8 TOrches enaBle yOU TO rePaIr The neck end OF The POWer caBle, Please Use sTOck cOde: XP3042: 300a
POWer caBle rePaIr kIT
nI - nOT IllUsTraTed
Sales: +44 (0) 1299 266800E-Mail: [email protected]
A
B
C
1D
23
44
5
6
7
8
9
10
11
12 13
16 14
15
17
18
19
20
2122
E
23
24
note: all ratings are based on a nominal gas flow of 18lpm. a lower gas flow will result in an increase in working temperature but it will not have any adverse affect as long as the gas flow is within the accepted limits for the welding amperage.
Table to show the affect on XP8 performance when using alternate gas types:
MIXED gAS (80/20) MIXED gAS (95/5) 100% CO2
Model amps kW amps kW amps kW
XP8-350a 350 10.5 300 9.0 425 14.9
amperages and duty cycles alone are arbitrary measures of a torches capability.For a more accurate appreciation wire type, gas type, flow rate and open circuit voltage must all be taken into consideration.
The XP8 is rated in amps as a guideline but the kilowattage requirement of a given application provides a far more accurate method for calculating torch selection.kilowattage represents the total power rating required and is calculated as follows:
(amps x Volts = Watts , 1000 Watts = 1 kW)
Welding amps x Welding Volts = kW
1000
selecTInG The cOrrecT XP8 TOrch
XP8 350A350a, 10.5kW, MIXed Gas (80/20) @ 80% dUTy cycle, en60974 -7 .040”- 1/16”/1.0MM TO 1.6MM WIres
air cooled Mig Welding TorchX
P8 T
orc
hes
Sales: +44 (0) 1299 266800E-Mail: [email protected] 17
ModelSTOCK CODE DESCRIPTIOn
XP350a-30e Welding Torch Package c/w euro Fitting x 3m
XP350a-40e Welding Torch Package c/w euro Fitting x 4m
XP350a-50e Welding Torch Package c/w euro Fitting x 5m
nozzlesSTOCK CODE DESCRIPTIOn
a XP3002-13 Tapered nozzle 1/2"/13mm
XP3002-16* conical nozzle 5/8"/16mm
XP3002-16l conical nozzle 5/8"/16mm extended
XP3002-19 cylindrical nozzle 3/4"/19mm
XP3002-19l cylindrical nozzle 3/4"/19mm extended
B XP3002-10T long Tapered nozzle 3mm/1/8" 10mm/3/8"
contact TipsSTOCK CODE SIZE
COnTACT TIPS, M10, CuCrZr
c XP3003-10 .040"/1.0mm
XP3003-10a .040"/1.0mm al
XP3003-12* .045"/1.2mm
XP3003-12a .045"/1.2mm al
XP3003-13 .052"/1.3mm
XP3003-14 .055"/1.4mm
XP3003-16 1/16"/1.6mm
TAPERED COnTACT TIPS, CuCrZr
d XP3003-10T 1.0mm/.040"
XP3003-12T 1.2mm/.045"
XP3003-13T 1.3mm/.052"
XP3003-14T 1.4mm/.055"
XP3003-16T 1.6mm/1/16"
linersSTOCK CODE SIZE
STEEL LInERS
e XP3524-12-30* .040-.045"/1.0-1.2mm x 3m/10ft
XP3524-12-40* .040-.045"/1.0-1.2mm x 4m/13ft
XP3524-12-50* .040-.045"/1.0-1.2mm x 5m/16ft
XP3524-16-30 .045-.063"/1.2-1.6mm x 3m/10ft
XP3524-16-40 .045-.063"/1.2-1.6mm x 4m/13ft
XP3524-16-50 .045-.063"/1.2-1.6mm x 5m/16ft
POLY-COPPER LInERS
nI XP2024Pc-12-30 .030-.045"/0.8-1.2mm x 3m/10ft
XP2024Pc-12-40 .030-.045"/0.8-1.2mm x 4m/13ft
XP2024Pc-12-50 .030-.045"/0.8-1.2mm x 5m/16ft
XP3524Pc-16-30 .045-.063"/1.2-1.6mm x 3m/10ft
XP3524Pc-16-40 .045-.063"/1.2-1.6mm x 4m/13ft
XP3524Pc-16-50 .045-.063"/1.2-1.6mm x 5m/16ft
linersSTOCK CODE SIZE
POLY-STEEL LInERS
XP2024Ps-12-30 .030-.045"/0.8-1.2mm x 3m/10ft
XP2024Ps-12-40 .030-.045"/0.8-1.2mm x 4m/13ft
XP2024Ps-12-50 .030-.045"/0.8-1.2mm x 5m/16ft
XP3524Ps-16-30 .045-.063"/1.2-1.6mm x 3m/10ft
XP3524Ps-16-40 .045-.063"/1.2-1.6mm x 4m/13ft
XP3524Ps-16-50 .045-.063"/1.2-1.6mm x 5m/16ft
components * denotes standard Build
STOCK CODE DESCRIPTIOn
1 XP3004B* diffuser-Moulded c/w ceramic Insert-M10 head
nI XP3004c diffuser-ceramic-M10 head
2 XP3505* head assembly-M10 Tips
3 XP3505T head assembly-M10 Tapered Tips
4 XP3506a* aluminium heat shield-M10 head
nI XP3506B heat shield-Moulded-M10 head
5 XP3501 swan neck
6 XP3507 lock nut M14
7 XP3088 cable support
8 XP3009 handle lock nut
9 XP3510-30 hyperflex™ cable assembly x 3m/10ft
XP3510-40 hyperflex™ cable assembly x 4m/13ft
XP3510-50 hyperflex™ cable assembly x 5m/16ft
10 XP2011 cable Terminal Female
11 XP2112 handle kit c/w lock nut and support
12 XP2013 hanger hook
13 XP2014 Trigger assembly
14 XP2015 cable Terminal Male
15 XP2016 lock nut M12
16 XP3017 cable support
17 XP2018 air cooled Gun Plug housing c/w nut
18 XP2019 Gun Plug screw
19 XP2020 Gun Plug nut
20 spring Pin 2 spring Pin assembly
21 XP2022 Gun Plug Body c/w spring Pins
22 XP2023 euro Body ‘O’ ring
23 XP2025 liners nipple ‘O’ rings
24 XP2026 liners retaining nut
ParWeld XP8 TOrches enaBle yOU TO rePaIr The neck end OF The POWer caBle, Please Use sTOck cOde: XP3542: 350a
POWer caBle rePaIr kIT
nI - nOT IllUsTraTed
XP8 To
rch
es
Sales: +44 (0) 1299 266800E-Mail: [email protected]
AB
C
1 D
2 3
4 4
5
6
7
8
9
10
11
12 13
16 14
15
17
1820
2122
E
2324
19
XP8 400A400a, 12kW, MIXed Gas (80/20) @ 80% dUTy cycle, en60974 -7 .045”- 3/32”/1.2MM TO 2.4MM WIres
air cooled Mig Torch
note: all ratings are based on a nominal gas flow of 18lpm. a lower gas flow will result in an increase in working temperature but it will not have any adverse affect as long as the gas flow is within the accepted limits for the welding amperage.
Table to show the affect on XP8 performance when using alternate gas types:
MIXED gAS (80/20) MIXED gAS (95/5) 100% CO2
Model amps kW amps kW amps kW
XP8-400a 400 12.0 300 9.0 480 17.2
amperages and duty cycles alone are arbitrary measures of a torches capability.For a more accurate appreciation wire type, gas type, flow rate and open circuit voltage must all be taken into consideration.
The XP8 is rated in amps as a guideline but the kilowattage requirement of a given application provides a far more accurate method for calculating torch selection.kilowattage represents the total power rating required and is calculated as follows:
(amps x Volts = Watts , 1000 Watts = 1 kW)
Welding amps x Welding Volts = kW
1000
selecTInG The cOrrecT XP8 TOrch
nozzlesSTOCK CODE DESCRIPTIOn
a XP3002-13 Tapered nozzle 1/2"/13mm
XP3002-16* conical nozzle 5/8"/16mm
XP3002-16l conical nozzle 5/8"/16mm extended
XP3002-19 cylindrical nozzle 3/4"/19mm
XP8
To
rch
es
ModelSTOCK CODE DESCRIPTIOn
XP400a-30e Welding Torch Package c/w euro Fitting x 3m
XP400a-40e Welding Torch Package c/w euro Fitting x 4m
XP400a-50e Welding Torch Package c/w euro Fitting x 5m
Sales: +44 (0) 1299 266800E-Mail: [email protected] 19
roll Markingall Parweld consumables are roll marked to enable you to identify genuine Parweld product.
nozzlesSTOCK CODE DESCRIPTIOn
XP3002-19l cylindrical nozzle 3/4"/19mm extended
B XP3002-10T long Tapered nozzle 3mm/1/8" 10mm/3/8"
contact TipsSTOCK CODE SIZE
COnTACT TIPS M10, CuCrZr
c XP3003-10a .040"/1.0mm, al
XP3003-12* .045"/1.2mm
XP3003-12a .045"/1.2mm, al
XP3003-13 .052"/1.3mm
XP3003-14 .055"/1.4mm
XP3003-16 1/16"/1.6mm
XP3003-18 .071"/1.8mm
XP3003-20 5/64"/2.0mm
XP3003-24 3/32"/2.4mm
TAPERED COnTACT TIPS, CuCrZr
d XP3003-10T 1.0mm/.040"
XP3003-12T 1.2mm/.045"
XP3003-13T 1.3mm/.052"
XP3003-14T 1.4mm/.055"
XP3003-16T 1.6mm/1/16"
XP3003-18T 1.8mm/.071"
XP3003-20T 2.0mm/5/64"
XP3003-24T 2.4mm/3/32"
linersSTOCK CODE SIZE
STEEL LInERS
e XP3524-12-30* .040-.045"/1.0-1.2mm x 3m/10ft
XP3524-12-40* .040-.045"/1.0-1.2mm x 4m/13ft
XP3524-12-50* .040-.045"/1.0-1.2mm x 5m/16ft
XP3524-16-30 .045-.063"/1.2-1.6mm x 3m/10ft
XP3524-16-40 .045-.063"/1.2-1.6mm x 4m/13ft
XP3524-16-50 .045-.063"/1.2-1.6mm x 5m/16ft
XP4024-24-30 .080-.095"/2.0-2.4mm x 3m/10ft
XP4024-24-40 .080-.095"/2.0-2.4mm x 4m/13ft
XP4024-24-50 .080-.095"/2.0-2.4mm x 5m/16ft
POLY-COPPER LInERS
nI XP3524Pc-16-30 .045-.063"/1.2-1.6mm x 3m/10ft
XP3524Pc-16-40 .045-.063"/1.2-1.6mm x 4m/13ft
XP3524Pc-16-50 .045-.063"/1.2-1.6mm x 5m/16ft
XP4024Pc-20-30 .063-.080"/1.6-2.0mm x 3m/10ft
XP4024Pc-20-40 .063-.080"/1.6-2.0mm x 4m/13ft
XP4024Pc-20-50 .063-.080"/1.6-2.0mm x 5m/16ft
linersSTOCK CODE SIZE
POLY-STEEL LInERS
XP3524Ps-16-30 .045-.063"/1.2-1.6mm x 3m/10ft
XP3524Ps-16-40 .045-.063"/1.2-1.6mm x 4m/13ft
XP3524Ps-16-50 .045-.063"/1.2-1.6mm x 5m/16ft
XP4024Ps-20-30 .063-.080"/1.6-2.0mm x 3m/10ft
XP4024Ps-20-40 .063-.080"/1.6-2.0mm x 4m/13ft
XP4024Ps-20-50 .063-.080"/1.6-2.0mm x 5m/16ft
components * denotes standard Build
STOCK CODE DESCRIPTIOn
1 XP3004B* diffuser-Moulded c/w ceramic Insert-M10 head
nI XP3004c diffuser-ceramic-M10 head
2 XP3505* head assembly-M10 Tips
3 XP3505T head assembly-M10 Tapered Tips
4 XP3506a* aluminium heat shield-M10 head
nI XP3506B heat shield-Moulded-M10 head
5 XP4001 swan neck
6 XP3507 lock nut M14
7 XP3088 cable support
8 XP3009 handle lock nut
9 XP4010-30 hyperflex™ cable assembly x 3m/10ft
XP4010-40 hyperflex™ cable assembly x 4m/13ft
XP4010-50 hyperflex™ cable assembly x 5m/16ft
10 XP2011 cable Terminal Female
11 XP2112 handle kit c/w lock nut and support
12 XP2013 hanger hook
13 XP2014 Trigger assembly
14 XP2015 cable Terminal Male
15 XP2016 lock nut M12
16 XP3088 cable support
17 XP2018 air cooled Gun Plug housing c/w nut
18 XP2019 Gun Plug screw
19 XP2020 Gun Plug nut
20 spring Pin 2 spring Pin assembly
21 XP2022 Gun Plug Body c/w spring Pins
22 XP2023 euro Body ‘O’ ring
23 XP2025 liners nipple ‘O’ rings
24 XP2026 liners retaining nut
ParWeld XP8 TOrches enaBle yOU TO rePaIr The neck end OF The POWer caBle, Please Use sTOck cOde: XP4042: 400a
POWer caBle rePaIr kIT
nI - nOT IllUsTraTed
XP8 To
rch
es
Sales: +44 (0) 1299 266800E-Mail: [email protected]
B
A
C
2
1
F
4
3
5
7
6
6
8
9
10
11
12 14
15
16
17
18
20
21
22
E
2324
19
E
D
2526
27
28
29
3031
32333435
9
13
note: all ratings are based on a nominal gas flow of 18lpm. a lower gas flow will result in an increase in working temperature but it will not have any adverse affect as long as the gas flow is within the accepted limits for the welding amperage.
Table to show the affect on XP8 performance when using alternate gas types:
MIXED gAS (80/20) MIXED gAS (95/5) 100% CO2
Model amps kW amps kW amps kW
XP8-320W 320 9.6 320 9.6 320 9.6
amperages and duty cycles alone are arbitrary measures of a torches capability.For a more accurate appreciation wire type, gas type, flow rate and open circuit voltage must all be taken into consideration.
The XP8 is rated in amps as a guideline but the kilowattage requirement of a given application provides a far more accurate method for calculating torch selection.kilowattage represents the total power rating required and is calculated as follows:
(amps x Volts = Watts , 1000 Watts = 1 kW)
Welding amps x Welding Volts = kW
1000
selecTInG The cOrrecT XP8 TOrch
ModelSTOCK CODE DESCRIPTIOn
XP320W-30e Welding Torch Package c/w euro Fitting x 3m
XP320W-40e Welding Torch Package c/w euro Fitting x 4m
XP320W-50e Welding Torch Package c/w euro Fitting x 5m
nozzlesSTOCK CODE DESCRIPTIOn
a XP2002-10 Tapered nozzle 3/8"/10mm
XP2002-13 Tapered nozzle 1/2"/13mm
XP2002-16* conical nozzle 5/8"/16mm
XP2002-16l conical nozzle 5/8"/16mm extended
XP2002-19 cylindrical nozzle 3/4"/19mm
XP2002-19l cylindrical nozzle 3/4"/19mm extended
B XP3002-13 Tapered nozzle 1/2"/13mm
XP3002-16 conical nozzle 5/8"/16mm
XP3002-16l conical nozzle 5/8"/16mm extended
roll Markingall Parweld consumables are roll marked to enable you to identify genuine Parweld product.
XP8 320W320a, 9.6kW, MIXed Gas (80/20) @ 100% dUTy cycle, en60974 -7 .030”- 1/16”/0.8MM TO 1.6MM WIres
Water cooled Mig Welding TorchX
P8 T
orc
hes
Sales: +44 (0) 1299 266800E-Mail: [email protected] 21
nozzlesSTOCK CODE DESCRIPTIOn
XP3002-19 cylindrical nozzle 3/4"/19mm
XP3002-19l cylindrical nozzle 3/4"/19mm extended
c XP2002-07T long Tapered nozzle 3mm/1/8" 7mm/9/32"
XP2002-10T long Tapered nozzle 3mm/1/8" 10mm/3/8"
contact TipsSTOCK CODE SIZE
COnTACT TIPS, M8, CuCrZr
d XP2003-08 .030"/0.8mm
XP2003-09 .035"/0.9mm
XP2003-10* .040"/1.0mm
XP2003-10a .040"/1.0mm, al
XP2003-12 .045"/1.2mm
XP2003-12a .045"/1.2mm, al
XP2003-13 .052"/1.3mm
COnTACT TIPS, M10, CuCrZr
e XP3003-08 .030"/0.8mm
XP3003-10 .040"/1.0mm
XP3003-10a .040"/1.0mm, al
XP3003-12 .045"/1.2mm
XP3003-12a .045"/1.2mm, al
XP3003-13 .052"/1.3mm
XP3003-14 .055"/1.4mm
XP3003-16 1/16"/1.6mm
TAPERED COnTACT TIPS, CuCrZr
F XP2003-06T 0.6mm/.023"
XP2003-08T 0.8mm/.030"
XP2003-09T 0.9mm/.035"
XP2003-10T 1.0mm/.040"
XP2003-12T 1.2mm/.045"
XP2003-13T 1.3mm/.052"
XP2003-14T 1.4mm/.055"
linersSTOCK CODE SIZE
STEEL LInERS
G XP2024-12-30* .040-.045"/1.0-1.2mm x 3m/10ft
XP2024-12-40* .040-.045"/1.0-1.2mm x 4m/13ft
XP2024-12-50* .040-.045"/1.0-1.2mm x 5m/16ft
XP3524-16-30 .045-.063"/1.2-1.6mm x 3m/10ft
XP3524-16-40 .045-.063"/1.2-1.6mm x 4m/13ft
XP3524-16-50 .045-.063"/1.2-1.6mm x 5m/16ft
POLY COPPER LInERS
nI XP2024Pc-12-30 .030-.045"/0.8-1.2mm x 3m/10ft
XP2024Pc-12-40 .030-.045"/0.8-1.2mm x 4m/13ft
XP2024Pc-12-50 .030-.045"/0.8-1.2mm x 5m/16ft
POLY-STEEL LInERS
nI XP2024Ps-12-30 .030-.045"/0.8-1.2mm x 3m/10ft
XP2024Ps-12-40 .030-.045"/0.8-1.2mm x 4m/13ft
XP2024Ps-12-50 .030-.045"/0.8-1.2mm x 5m/16ft
XP3524Ps-16-30 .045-.063"/1.2-1.6mm x 3m/10ft
XP3524Ps-16-40 .045-.063"/1.2-1.6mm x 4m/13ft
XP3524Ps-16-50 .045-.063"/1.2-1.6mm x 5m/16ft
components * denotes standard Build
STOCK CODE DESCRIPTIOn
1 XP2004B* diffuser-Plastic-M8 head
nI XP2004c diffuser-ceramic-M8 head
2 XP3004B diffuser-Moulded c/w ceramic Insert-M10 head
nI XP3004c diffuser-ceramic-M10 head
3 XP2005* head assembly-M8 Tips
4 XP3005 head assembly-M10 Tips
5 XP2005T head assembly-M8 Tapered Tips
6 XP2006a* aluminium heat shield-M8 head
nI XP2006B heat shield-Moulded-M8 head
7 XP3006a aluminium heat shield-M10 head
nI XP3006B heat shield-Moulded-M10 head
8 XP3201 swan neck
9 XP3228 Grub screw-M6
10 XP3229 O’ ring Pack
11 XP3230-30 Power cable assembly x 3m/10ft
XP3230-40 Power cable assembly x 4m/13ft
XP3230-50 Power cable assembly x 5m/16ft
12 XP3231-30 liners conduit assembly x 3m/10ft
XP3231-40 liners conduit assembly x 4m/13ft
XP3231-50 liners conduit assembly x 5m/16ft
13 XP3232-30 Water hose assembly x 3m/10ft
XP3232-40 Water hose assembly x 4m/13ft
XP3232-50 Water hose assembly x 5m/16ft
14 XP3233-30 switch lead assembly x 3m/10ft
XP3233-40 switch lead assembly x 4m/13ft
XP3233-50 switch lead assembly x 5m/16ft
15 XP2011 cable Terminal Female
16 XP3224 Ball Joint assembly
17 XP3288 cable support
18 XP3112 handle kit c/w Ball Joint and support
19 XP2013 hanger hook
20 XP2014 Trigger assembly
21 XP3235-30 canvas cover assembly x 3m/10ft
XP3235-40 canvas cover assembly x 4m/13ft
XP3235-50 canvas cover assembly x 5m/16ft
22 XP3018 cable support
23 XP3027 cable support nut
24 XP3236 canvas cover clamp and retainer
25 XP3237 Water hose nipple
26 XP3238 Water Outlet hose assembly
27 XP3240 Water cooled housing c/w supports
28 XP2019 Gun Plug screw
29 XP2020 Gun Plug nut
30 XP2015 cable Terminal Male
31 spring Pin 2 spring Pin assembly
32 XP3241 Gun Plug Body c/w spring Pins
33 XP2023 Gun Plug Body ‘O’ ring
34 XP2025 liners nipple ‘O’ rings
35 XP2026 liners retaining nut
Parweld XP8 Torches enable you to repair the neck end of the Power cable, please use stock code: XP3242: 320a Power cable
repair kit
nI - nOT IllUsTraTed
XP8 To
rch
es
Sales: +44 (0) 1299 266800E-Mail: [email protected]
AB
C
1D
23
44
56
7
8
9
10
11
12
13
14
15
16 17
18
2021
22
23
24
19
E26
2728
29303132
6
25
XP8 450W450a, 15.8kW, MIXed Gas (80/20) @ 100% dUTy cycle, en60974 -7 .040”- 3/32”/1.0MM TO 2.4MM WIres
Water cooled Mig Welding Torch
note: all ratings are based on a nominal gas flow of 18lpm. a lower gas flow will result in an increase in working temperature but it will not have any adverse affect as long as the gas flow is within the accepted limits for the welding amperage.
Table to show the affect on XP8 performance when using alternate gas types:MIXED gAS (80/20) MIXED gAS (95/5) 100% CO2
Model amps kW amps kW amps kW
XP8-450W 450 15.8 450 15.8 450 15.8
amperages and duty cycles alone are arbitrary measures of a torches capability.For a more accurate appreciation wire type, gas type, flow rate and open circuit voltage must all be taken into consideration.
The XP8 is rated in amps as a guideline but the kilowattage requirement of a given application provides a far more accurate method for calculating torch selection.kilowattage represents the total power rating required and is calculated as follows:
(amps x Volts = Watts , 1000 Watts = 1 kW)
Welding amps x Welding Volts = kW
1000
selecTInG The cOrrecT XP8 TOrch
ModelSTOCK CODE DESCRIPTIOn
XP450W-30e Welding Torch Package c/w euro Fitting x 3m
XP450W-40e Welding Torch Package c/w euro Fitting x 4m
XP450W-50e Welding Torch Package c/w euro Fitting x 5m
nozzlesSTOCK CODE DESCRIPTIOn
a XP3002-13 Tapered nozzle 1/2"/13mmXP3002-16* conical nozzle 5/8"/16mmXP3002-16l conical nozzle 5/8"/16mm extendedXP3002-19 cylindrical nozzle 3/4"/19mmXP3002-19l cylindrical nozzle 3/4"/19mm extended
B XP3002-10T long Tapered nozzle 3mm/1/8"/10mm/3/8"XP8
To
rch
es
Sales: +44 (0) 1299 266800E-Mail: [email protected] 23
contact Tips
STOCK CODE SIZE
COnTACT TIPS, COnTact Tips, M10, CuCrZr
c XP3003-10 .040"/1.0mm
XP3003-10a .040"/1.0mm, al
XP3003-12* .045"/1.2mm
XP3003-12a .045"/1.2mm, al
XP3003-13 .052"/1.3mm
XP3003-14 .055"/1.4mm
XP3003-16 1/16"/1.6mm
XP3003-20 5/64"/2.0mm
XP3003-24 3/32"/2.4mm
TAPERED COnTACT TIPS, CuCrZr
d XP3003-10T 1.0mm/.040"
XP3003-12T .2mm/.045"
XP3003-13T 1.3mm/.052"
XP3003-14T 1.4mm/.055"
XP3003-16T 1.6mm/1/16"
XP3003-18T 1.8mm/.071"
XP3003-20T 2.0mm/5/64"
XP3003-24T 2.4mm/3/32"
linersSTOCK CODE SIZE
STEEL LInERS
e XP3524-12-30* .040-.045"/1.0-1.2mm x 3m/10ft
XP3524-12-40* .040-.045"/1.0-1.2mm x 4m/13ft
XP3524-12-50* .040-.045"/1.0-1.2mm x 5m/16ft
XP3524-16-30 .063"/1.6mm x 3m/10ft
XP3524-16-40 .063"/1.6mm x 4m/13ft
XP3524-16-50 .063"/1.6mm x 5m/16ft
XP4024-24-30 .080-.0.95"/2.0-2.4mm x 3m/10ft
XP4024-24-40 .080-.0.95"/2.0-2.4mm x 4m/13ft
XP4024-24-50 .080-.0.95"/2.0-2.4mm x 5m/16ft
POLY-COPPER LInERS
nI XP2024Pc-12-30 .030-.045"/0.8-1.2mm x 3m/10ft
XP2024Pc-12-40 .030-.045"/0.8-1.2mm x 4m/13ft
XP2024Pc-12-50 .030-.045"/0.8-1.2mm x 5m/16ft
XP3524Pc-16-30 .045-.063"/1.2-1.6mm x 3m/10ft
XP3524Pc-16-40 .045-.063"/1.2-1.6mm x 4m/13ft
XP3524Pc-16-50 .045-.063"/1.2-1.6mm x 5m/16ft
XP4024Pc-20-30 .063-.080"/1.6-2.0mm x 3m/10ft
XP4024Pc-20-40 .063-.080"/1.6-2.0mm x 4m/13ft
XP4024Pc-20-50 .063-.080"/1.6-2.0mm x 5m/16ft
XP3524Ps-16-30 .045-.063"/1.2-1.6mm x 3m/10ft
XP3524Ps-16-40 .045-.063"/1.2-1.6mm x 4m/13ft
XP3524Ps-16-50 .045-.063"/1.2-1.6mm x 5m/16ft
XP4024Ps-20-30 .063-.080"/1.6-2.0mm x 3m/10ft
XP4024Ps-20-40 .063-.080"/1.6-2.0mm x 4m/13ft
XP4024Ps-20-50 .063-.080"/1.6-2.0mm x 5m/16ft
components * denotes standard Build
STOCK CODE DESCRIPTIOn
1 XP3004B* diffuser Moulded-M10 head
nI XP3004c diffuser ceramic-M10 head
2 XP3505* head assembly-M10 Tips
3 XP3505T head assembly-M10 Tapered Tips
4 XP3506a* aluminium heat shield-M10 head
nI XP3506B heat shield-Moulded-M10 head
5 XP4501 swan neck
6 XP3228 Grub screw-M6
7 XP3229 O’ ring Pack
8 XP3230-30 Power cable assembly x 3m/10ft
XP3230-40 Power cable assembly x 4m/13ft
XP3230-50 Power cable assembly x 5m/16ft
9 XP3231-30 liners conduit assembly x 3m/10ft
XP3231-40 liners conduit assembly x 4m/13ft
XP3231-50 liners conduit assembly x 5m/16ft
10 XP3232-30 Water hose assembly x 3m/10ft
XP3232-40 Water hose assembly x 4m/13ft
XP3232-50 Water hose assembly x 5m/16ft
11 XP3233-30 switch lead assembly x 3m/10ft
XP3233-40 switch lead assembly x 4m/13ft
XP3233-50 switch lead assembly x 5m/16ft
12 XP2011 cable Terminal Female
13 XP3224 Ball Joint assembly
14 XP3288 cable support
15 XP3112 handle kit c/w Ball Joint and support
16 XP2013 hanger hook
17 XP2014 Trigger assembly
18 XP3235-30 canvas cover assembly x 3m/10ft
XP3235-40 canvas cover assembly x 4m/13ft
XP3235-50 canvas cover assembly x 5m/16ft
19 XP3018 cable support
20 XP3027 cable support nut
21 XP3236 canvas cover clamp and retainer
22 XP3237 Water hose nipple
23 XP3238 Water Outlet hose assembly
24 XP3240 Water cooled housing c/w supports
25 XP2019 Gun Plug screw
26 XP2020 Gun Plug nut
27 XP2015 cable Terminal Male
28 spring Pin 2 spring Pin assembly
29 XP3241 Gun Plug Body c/w spring Pins
30 XP2023 Gun Plug Body ‘O’ ring
31 XP2025 liners nipple ‘O’ rings
32 XP2026 liners retaining nut
ParWeld XP8 TOrches enaBle yOU TO rePaIr The neck end OF The POWer caBle, Please Use sTOck cOde: XP4542: 450
nI - nOT IllUsTraTed
XP8 To
rch
es
Sales: +44 (0) 1299 266800E-Mail: [email protected]
1 2 3
4
8
A B
C
5
67
1110
12
15
16
18
17
1920
21
22
14
23
242526
27
2829
30
31
9
13
XP8 350A PP350a, 10.5kW, MIXed Gas (80/20) @ 80% dUTy cycle, en60974-7 0.040”/1.0MM TO 1/16”/1.6MM WIres
ModelSTOCK CODE 6M 8M 10M DESCRIPTIOn
XP35P3500 -60e -80e -10e 3.5” x 180” neck, euro
XP35P3500 -60er -80er -10er 3.5” x 180” neck, euro, remote
XP35P4545 -60e -80e -10e 4.5” x 45° neck, euro
XP35P4545 -60er -80er -10er 4.5” x 45° neck, euro, remote
nozzlesSTOCK CODE DESCRIPTIOn
a XP3002-13 Tapered nozzle 1/2” / 13mm Bore
XP3002-16* conical nozzle 5/8” / 16mm Bore
XP3002-16l conical nozzle 5/8” / 16mm Bore extended
XP3002-19 cylindrical nozzle 3/4” / 19mm Bore
XP3002-19l cylindrical nozzle 3/4” / 19mm Bore extended
linersSTOCK CODE SIZE
TEFLOn LInERS
c PP1536-60 0.025”-0.035”/0.6-0.9mm x 6m
PP1536-80 0.025”-0.035”/0.6-0.9mm x 8m
PP1536-10 0.025”-0.035”/0.6-0.9mm x 10m
PP2513-60 0.040”-0.045”/1.0-1.2mm x 6m
PP2513-80 0.040”-0.045”/1.0-1.2mm x 8m
PP2513-10 0.040”-0.045”/1.0-1.2mm x 10m
PP3626-60 1/16”/1.6mm x 6m
PP3626-80 1/16”/1.6mm x 8m
linersSTOCK CODE SIZE
PP3626-10 1/16”/1.6mm x 10m
contact TipsSTOCK CODE SIZE
M10, CuCrZr
B XP3003-10 0.040”/1.0mm
XP3003-12 0.045”/1.2mm
XP3003-14 0.055”/1.4mm
XP3003-16 1/16”/1.6mm
M10, CuCrZr, AL WIRE
XP3003-10a 0.040”/1.0mm
XP3003-12a* 0.045”/1.2mm
XP3003-14a 0.055”/1.4mm
XP3003-16a 1/16”/1.6mm
XP8
To
rch
es
32
coming soonask sales for more information
Sales: +44 (0) 1299 266800E-Mail: [email protected] 25
XP8 To
rch
es
harness componentsSTOCK CODE DESCRIPTIOn
d PP0118-60 Outer liner assembly x 6m
PP0118-80 Outer liner assembly x 8m
PP0118-10 Outer liner assembly x 10m
e PP3519-60 Power cable assembly x 6m
PP3519-80 Power cable assembly x 8m
PP3519-10 Power cable assembly x 10m
F PP0120-60 Gas hose assembly x 6m
PP0120-80 Gas hose assembly x 8m
PP0120-10 Gas hose assembly x 10m
G PP0122-60 Motor lead assembly x 6m
PP0122-80 Motor lead assembly x 8m
PP0122-10 Motor lead assembly x 10m
h PP0123-60 switch lead assembly x 6m
PP0123-80 switch lead assembly x 8m
PP0123-10 switch lead assembly x 10m
I PP0124-60 remote lead assembly x 6m
PP0124-80 remote lead assembly x 8m
PP0124-10 remote lead assembly x 10m
J PP0125-60 canvas cover assembly x 6m
PP0125-80 canvas cover assembly x 8m
PP0125-10 canvas cover assembly x 10m
D
E
F
g
h
J
I
components * denotes standard Build
STOCK CODE DESCRIPTIOn
1 XP3004B* diffuser - Moulded c/w ceramic Insert
XP3004c diffuser - ceramic White
XP3004s diffuser - ceramic Grey
2 XP3505* head assembly - M10 Tips
3 XP3506a* heat shield - aluminium - M10 head
XP3505B heat shield - Moulded - M10 head
4 XP35Oar30 XP8 350a straight neck, 3.5” x 180°
5 XP350ar54 XP8 350a swan neck, 4.5” x 45°
6 PX0812B neck liner, 0.030”-0.045” / 0.8-1.2mm Wires
7 PP0101 air cooled Torch Body (Pistol drive)
8 PP0102 dc Motor & Gear assembly (Pistol drive) c/w screws
9 PP0103 Wire Guide nipple kit c/w screw (roll Feed)
10 PP0104 Wire Guide nipple kit c/w screw, liner & O ring (neck Feed)
11 PP0105 liner & O ring seal (For neck In Feed Guide nipple)
12 PP12ars Feed & Pressure roll set - 1.2mm - Plain U Groove (aluminium Wire)
13 PP0106 roll screws & drive roll retaining cap kit
14 PP3507-60 harness assembly x 6m
PP3507-80 harness assembly x 8m
PP3507-10 harness assembly x 10m
PP3508-60 harness assembly c/w remote control leads x 6m
PP3508-80 harness assembly c/w remote control leads x 8m
components * denotes standard Build
STOCK CODE DESCRIPTIOn
PP3508-10 harness assembly c/w remote control leads x 10m
15 PP5037 conduit clamp 11.3mm
16 PP5024 Gas hose clamp 9.5mm
17 PP0109 handle kit c/w screws, Ball Joint lock nut and support
18 PP0110 remote speed control kit
19 PP0111 handle Fixing screw kit
20 PP0112 Trigger kit c/w Body Moulding, Microswitch, spring and dowels
21 PP8031 Ball Joint assembly c/w clamp
22 PP8032 cable support
23 PP8027 spring cable support - rear
24 PP0113 Gun Plug housing c/w lock nut and lead support
25 PP2519 Gun Plug nut c/w Insert
26 PP0114 air cooled euro Gun Plug Body c/w spring Pins
27 sPrInG PIn 2 spring Pin assembly
28 PP1524 Gun Plug Body O ring
29 PP1529 liner retaining nut
30 PP1526 Gun Plug screw
31 PP0115 control lead assembly (drive)
PP0116 control lead assembly (drive & remote)
32 PP0117 Motor driver control Module (18-42Vac/Vdc Input)
Sales: +44 (0) 1299 266800E-Mail: [email protected]
XP8 450A PP450a, 15.8kW, MIXed Gas (80/20) @ 100% dUTy cycle, en60974-7, 0.040”/1.0MM TO 1/6”/1.6MM WIres
ModelSTOCK CODE 6M 8M 10M DESCRIPTIOn
XP45P3500 -60e -80e -10e 3.5” x 180” neck, euro
XP45P3500 -60er -80er -10er3.5” x 180” neck, euro, remote
XP45P4545 -60e -80e -10e 4.5” x 45° neck, euro
XP45P4545 -60er -80er -10er4.5” x 45° neck, euro, remote
nozzlesSTOCK CODE DESCRIPTIOn
a XP3002-13 Tapered nozzle 1/2” / 13mm Bore
XP3002-16* conical nozzle 5/8” / 16mm Bore
XP3002-16l conical nozzle 5/8” / 16mm Bore extended
XP3002-19 cylindrical nozzle 3/4” / 19mm Bore
XP3002-19l cylindrical nozzle 3/4” / 19mm Bore extended
contact TipsSTOCK CODE DESCRIPTIOn
M10, CuCrZr
B XP3003-10 0.040”/1.0mm
XP3003-12 0.045”/1.2mm
XP3003-14 0.055”/1.4mm
XP3003-16 1/16”/1.6mm
M10, CuCrZr, AL WIRE
XP3003-10a 0.040”/1.0mm
XP3003-12a* 0.045”/1.2mm
XP3003-14a 0.055”/1.4mm
XP8
To
rch
es
15
1 2 3
10
4
A B
C
5
6
11
12
13
8
716
17
18
19
23
20
21
22
252627
28
3031
32
29
9
14
24
32
contact TipsSTOCK CODE DESCRIPTIOn
XP3003-16a 1/16”/1.6mm
linersSTOCK CODE SIZE
TEFLOn LInERS
c B1536-60 0.025”-0.035”/0.6-0.9mm x 6m
B1536-80 0.025”-0.035”/0.6-0.9mm x 8m
B1536-10 0.025”-0.035”/0.6-0.9mm x 10m
B2513-60 0.040”-0.045”/1.0-1.2mm x 6m
B2513-80 0.040”-0.045”/1.0-1.2mm x 8m
B2513-10 0.040”-0.045”/1.0-1.2mm x 10m
B3626-60 1/16”/1.6mm x 6m
B3626-80 1/16”/1.6mm x 8m
B3626-10 1/16”/1.6mm x 10m
coming soonask sales for more information
Sales: +44 (0) 1299 266800E-Mail: [email protected] 27
XP8 To
rch
escomponents * denotes standard Build
STOCK CODE DESCRIPTIOn
1 XP3004B* diffuser - Moulded c/w ceramic Insert
XP3004c diffuser - ceramic White
XP3004s diffuser - ceramic Grey
2 XP3505* head assembly - M10 Tips
3 XP3506a* heat shield - aluminium - M10 head
XP3505B heat shield - Moulded - M10 head
4 XP450Wr30 XP8 450W straight neck, 3.5” x 180°
5 XP450Wr54 XP8 450W swan neck, 4.5” x 45°
6 PX0812B neck liner, 0.030”-0.045” / 0.8-1.2mm Wires
7 PP0201 Water cooled Torch Body (Pistol drive)
8 PP0102dc Motor & Gear assembly (Pistol drive) c/w screws
9 PP0103 Wire Guide nipple kit c/w screw (roll Feed)
10 PP0104Wire Guide nipple kit c/w screw, liner & O ring (neck Feed)
11 PP0105liner & O ring seal (For neck In Feed Guide nipple)
12 PP12arsFeed & Pressure roll set - 1.2mm - Plain U Groove (aluminium Wire)
13 PP0106 roll screws & drive roll retaining cap kit
14 PP4507-60 harness assembly x 6m
PP4507-80 harness assembly x 8m
PP4507-10 harness assembly x 10m
harness componentsSTOCK CODE DESCRIPTIOn
d PP0118-60 Outer liner assembly x 6m
PP0118-80 Outer liner assembly x 8m
PP0118-10 Outer liner assembly x 10m
e PP4519-60 Power cable assembly x 6m
PP4519-80 Power cable assembly x 8m
PP4519-10 Power cable assembly x 10m
F PP0120-60 Gas hose assembly x 6m
PP0120-80 Gas hose assembly x 8m
PP0120-10 Gas hose assembly x 10m
G PP0221-60 Water Inlet hose assembly x 6m
PP0221-80 Water Inlet hose assembly x 8m
PP0221-10 Water Inlet hose assembly x 10m
h PP0122-60 Motor lead assembly x 6m
PP0122-80 Motor lead assembly x 8m
PP0122-10 Motor lead assembly x 10m
I PP0123-60 switch lead assembly x 6m
PP0123-80 switch lead assembly x 8m
PP0123-10 switch lead assembly x 10m
J PP0124-60 remote lead assembly x 6m
PP0124-80 remote lead assembly x 8m
PP0124-10 remote lead assembly x 10m
k PP0225-60 canvas cover assembly x 6m
PP0225-80 canvas cover assembly x 8m
PP0225-10 canvas cover assembly x 10m
components * denotes standard Build
STOCK CODE DESCRIPTIOn
PP4508-60harness assy c/w remote control leads x 6m
PP4508-80harness assy c/w remote control leads x 8m
PP4508-10harness assy c/w remote control leads x 10m
15 PP5037 conduit clamp 11.3mm
16 PP5024 Gas hose clamp 9.5mm
17 PP0109handle kit c/w screws, Ball Joint lock nut and support
18 PP0110 remote speed control kit
19 PP0111 handle Fixing screw kit
20 PP0112Trigger kit c/w Body Moulding, Microswitch, spring and dowels
21 PP8031 Ball Joint assembly c/w clamp
22 PP8032 cable support
23 PP8027 spring cable support - rear
24 PP5017 Water Outlet hose assembly
25 PP0213Gun Plug housing c/w lock nut and hose support
26 PP2519 Gun Plug nut c/w Insert
27PP0214
Water cooled euro Gun Plug Body c/w spring Pins
28 sPrInG PIn 2 spring Pin assembly
29 PP1524 Gun Plug Body O ring
30 PP1529 liner retaining nut
31 PP1526 Gun Plug screw
32 PP0115 control lead assembly (drive)
PP0116 control lead assembly (drive & remote)
33 PP0117Motor driver control Module (18-42Vac/Vdc Input)
D
E
F
h
J
g
K
I