PARTS LIST - Sitzman Supplysitzmansupply.com/resources/pdf_bin//clSeries.pdf28 Stuffing Box (Type...
Transcript of PARTS LIST - Sitzman Supplysitzmansupply.com/resources/pdf_bin//clSeries.pdf28 Stuffing Box (Type...
- 1 -
KEY # DESCRIPTION QTY
1 Casing 1
2 Impeller 1
3 Cover 1
4 Impeller Screw 1
5 O-ring 1, 2 or 3
6 Wingnut 6 or 8
7 Stud, Casing / Cover 6 or 8
8 Cover O-ring 1
9 Screw, Seal Gland 4
10 Seal Gland 1
11 Gasket 2
12 Stationary Seal 1
13 Nut, Casing / Adapter 2 or 4
14 Washer, Casing / Adapter 2 or 4
15 Rotating Seal 1 or 2
16 Spring 1
17 Drive Collar 1
18 Drive Collar, Stainless Steel 1
19 Pin, Drive Collar 1
20 O-ring, Stuffing Box 1
21 Single Flush Lip Seal 1
22 Stuffing Box (Type FG) 1
23 Screw, Stuffing Box 2
24 Flush Pipe 2
PARTS LIST
All orders for repair parts must contain the following:
1. Complete model number (located on nameplate).
2. Pump serial number (located on nameplate).
3. Description and part key number from the parts list.
The exploded view and parts key facilitate ordering repair parts from Tri-Clover. All parts for theCL pump are keyed to the parts list.
ORDERING INFORMATION
O-ring requirements:Impeller - 1 o-ring (CL4311, 6410 - use key #49, 1 o-ring)Type DG Seal - 1 o-ringType FG Seal - 2 o-ringsType EG Seal - 2 o-rings
EG Seal requires two Rotating Seals.
CL4311 and CL6410 require 8 wing nuts and studs.
CL4311 and CL6410 require 4 nuts and 4 washers.
CL4311 and CL6410 do not require a washer for the seal gland.
KEY # DESCRIPTION QTY
25 Spacing Ring 1
26 Stationary Seal, Rear 1
27 O-ring, Stationary Seal 1
28 Stuffing Box (Type EG) 1
29 Adapter 1
30 Screw, Motor 4
31 Washer, Motor 4
32 Seal Guard 1
33 Screw, Seal Guard 1
34 Stub Shaft 1
35 Compression Ring, Threaded 1
36 Compression Ring 1
37 Screw, Compression Ring 6
38 Washer, Compression Ring, 6
Seal Gland 4
39 Pin, Stub Shaft 1
40 Retaining Ring, Stub Shaft 1
41 Leg Bracket 2
42 Screw, Leg Bracket 4
43 Washer, Leg Bracket 4
44 Set Screw, Adjustable Leg 4
45 Adjustable Leg 4
46 Motor 1
47 Stuffing Box (John Crane) 1
48 John Crane Double 8 Seal 1
1
3
4
4
2
3
1
2
4
5
3
5
6
6 CL4311 pumps with frame size 320 andlarger use motors with special Duplex thrustbearings. Contact your local Tri-Cloverdistributor or Tri-Clover for more information.
Required on 1½ and 2 horsepower motorsonly.
7
7
- 2 -
PARTS LISTFOR ALL CL SERIES PUMPSEXPLODED VIEW
TYPE DG - EXTERNAL BALANCED SEAL
TYPE FG - WATER COOLED SINGLE SEAL TYPE EG - WATER COOLED BALANCEDDOUBLE SEAL
31
4243
46
45
4144
39
3534
3738
40
33
32
3014
13
1110
7
6
52
1
48
3
29
See SealTypesBelow
36
11
9
12
38
JOHN CRANE DOUBLE 8 SEAL
4727
26
20
48
- 3 -
PARTS LIST
CROSS SECTIONAL VIEW
KEY # DESCRIPTION QTY
1 Casing 1
2 Impeller 1
3 Cover 1
4 Impeller Screw 1
5 O-ring 1, 2 or 3
6 Wingnut 6 or 8
7 Stud, Casing / Cover 6 or 8
8 Cover O-ring 1
9 Screw, Seal Gland 4
10 Seal Gland 1
11 Gasket 2
12 Stationary Seal 1
13 Nut, Casing / Adapter 2 or 4
14 Washer, Casing / Adapter 2 or 4
15 Rotating Seal 1 or 2
16 Spring 1
17 Drive Collar 1
18 Drive Collar, Stainless Steel 1
19 Pin, Drive Collar 1
20 O-ring, Stuffing Box 1
21 Single Flush Lip Seal 1
22 Stuffing Box (Type FG) 1
23 Screw, Stuffing Box 2
24 Flush Pipe 2
KEY # DESCRIPTION QTY
25 Spacing Ring 1
26 Stationary Seal, Rear 1
27 O-ring, Stationary Seal 1
28 Stuffing Box (Type EG) 1
29 Adapter 1
30 Screw, Motor 4
31 Washer, Motor 4
32 Seal Guard 1
33 Screw, Seal Guard 1
34 Stub Shaft 1
35 Compression Ring, Threaded 1
36 Compression Ring 1
37 Screw, Compression Ring 6
38 Washer, Compression Ring, 6
Seal Gland 4
39 Pin, Stub Shaft 1
40 Retaining Ring, Stub Shaft 1
41 Leg Bracket 2
42 Screw, Leg Bracket 4
43 Washer, Leg Bracket 4
44 Set Screw, Adjustable Leg 4
45 Adjustable Leg 4
46 Motor 1
47 Stuffing Box (John Crane) 1
48 John Crane Double 8 Seal 1
1
O-ring requirements:Impeller - 1 o-ring (CL4311, 6410 - use key #49, 1 o-ring)Type DG Seal - 1 o-ringType FG Seal - 2 o-ringsType EG Seal - 2 o-rings
EG Seal requires two Rotating Seals.
CL4311 and CL6410 require 8 wing nuts and studs.
CL4311 and CL6410 require 4 nuts and 4 washers.
CL4311 and CL6410 do not require a washer for the seal gland.
3
4
4
2
3
5
1
2
4
5
3
6
6 CL4311 pumps with frame size 320 andlarger use motors with special Duplex thrustbearings. Contact your local Tri-Cloverdistributor or Tri-Clover for more information.
Required on 1½ and 2 horsepower motorsonly.
7
7
- 4 -
13 14
5
4
11
2
3
8
61101516323933363729303546 27
5 5
40
11
12
4445 43 42 43 45 44 41 38 34 17 5 18 22 2421 20 23 26 28 24 23 1 55 20
1516251516197931
26 47 20 23
27 48
38
Type DG - External Type fg-Water Cooled Type eg-Water Cooled John Crane
Required on 1½and 2 horsepower DG SEAL FOR THE CL4311 and
CL6410 ONLY:
Parts List
- 4 -
PARTS LISTCL PUMP REPLACEMENT PARTS
KeyNo.
DescriptionCL2264 CL2265 CL2284 CL3285 CL3295
Part Number Part Number Part Number Part Number Part Number1* Casing - Tri-Clamp, Industrial 9612-7091-15 9612-7093-15 9612-7095-15 9612-7094-15 9612-7096-15
1* Casing - Tri-Clamp, Sanitary 9612-7091-04 9612-7093-04 9612-7095-04 9612-7094-04 9612-7096-04
1* Casing - Tri-Clamp, Sanitary Plus 9612-7091-01 9612-7093-01 9612-7095-01 9612-7094-01 9612-7096-01
2** Impeller - Full Size, Industrial 9612-7038-50 9612-7039-50 9612-7045-50 9612-7044-50 9612-7040-50
2** Impeller - Full Size, Sanitary, San. Plus 9612-7038-02 9612-7039-02 9612-7045-02 9612-7044-02 9612-7040-02
3* Cover - Tri-Clamp, Industrial 9612-7101-15 9612-7103-15 9612-7105-15 9612-7104-15 9612-7106-15
3* Cover - Tri-Clamp, Sanitary 9612-7101-04 9612-7101-04 9612-7101-04 9612-7101-04 9612-7101-04
3* Cover - Tri-Clamp, Sanitary Plus 9612-7101-01 9612-7101-01 9612-7101-01 9612-7101-01 9612-7101-01
4 Impeller Screw 9612-7070-02 9612-7070-02 9612-7070-02 9612-7070-02 9612-7070-02
5 O-ring - Buna N 9612-7301-01 9612-7301-01 9612-7301-01 9612-7301-01 9612-7301-01
5 O-ring - EPDM 9612-7301-02 9612-7301-02 9612-7301-02 9612-7301-02 9612-7301-02
5 O-ring - SFY (Fluoroelastomer) 9612-7301-03 9612-7301-03 9612-7301-03 9612-7301-03 9612-7301-03
6 Wingnut 9612-7308-01 9612-7308-01 9612-7309-01 9612-7309-01 9612-7309-01
7 Stud, Casing / Cover 9612-7304-01 9612-7304-01 9612-7305-01 9612-7305-01 9612-7305-01
8 Cover O-ring - Buna N 751560 751561 751563 751563 751578
8 Cover O-ring - EPDM 751543 751556 751558 751558 751559
8 Cover O-ring - SFY (Fluoroelastomer) 751519 751529 751536 751536 751542
9 - 12 (Seal Parts) Refer to Seal Replacement Parts later in this manual.
13 Nut, Casing / Adapter 9612-7306-01 9612-7306-01 9612-7306-01 9612-7306-01 9612-7306-01
14 Washer, Casing/Adapter 9612-7307-01 9612-7307-01 9612-7307-01 9612-7307-01 9612-7307-01
15 - 28 (Seal Parts) Refer to Seal Replacement Parts later in this manual.
* Other port connections available upon request. Contact Tri-Clover for details.** Cut down impeller sizes available upon request. Contact Tri-Clover for details.
- 5 -
PARTS LISTCL PUMP REPLACEMENT PARTS
KeyNo.
DescriptionCL4311 CL4359 CL4378 CL4387 CL4488
Part Number Part Number Part Number Part Number Part Number1* Casing - Tri-Clamp, Industrial 9612-7100-15 9612-7092-15 9612-7097-15 9612-7098-15 9612-7099-15
1* Casing - Tri-Clamp, Sanitary 9612-7100-04 9612-7092-04 9612-7097-04 9612-7098-04 9612-7099-04
1* Casing - Tri-Clamp, Sanitary Plus 9612-7100-01 9612-7092-01 9612-7097-01 9612-7098-01 9612-7099-01
2** Impeller - Full Size, Industrial 9612-7169-50 9612-7043-50 9612-7046-50 9612-7041-50 9612-7042-50
2** Impeller - Full Size, Sanitary, San. Plus 9612-7169-02 9612-7043-02 9612-7046-02 9612-7041-02 9612-7042-02
3* Cover - Tri-Clamp, Industrial 9612-7110-15 9612-7102-15 9612-7107-15 9612-7108-15 9612-7109-15
3* Cover - Tri-Clamp, Sanitary 9612-7110-04 9612-7102-04 9612-7107-04 9612-7108-04 9612-7109-04
3* Cover - Tri-Clamp, Sanitary Plus 9612-7110-01 9612-7102-01 9612-7107-01 9612-7108-01 9612-7109-01
4 Impeller Screw 9612-7170-01 9612-7070-02 9612-7070-02 9612-7070-02 9612-7070-02
5 O-ring - Buna N 9612-7325-01 9612-7301-01 9612-7301-01 9612-7301-01 9612-7301-01
5 O-ring - EPDM 9612-7325-02 9612-7301-02 9612-7301-02 9612-7301-02 9612-7301-02
5 O-ring - SFY (Fluoroelastomer) 9612-7325-03 9612-7301-03 9612-7301-03 9612-7301-03 9612-7301-03
6 Wingnut 9612-7309-01 9612-7308-01 9612-7309-01 9612-7309-01 9612-7309-01
7 Stud, Casing / Cover 9612-7326-01 9612-7304-01 9612-7305-01 9612-7305-01 9612-7305-01
8 Cover O-ring - Buna N 9612-7323-02 751560 751563 751578 751578
8 Cover O-ring - EPDM 9612-7323-01 751543 751558 751559 751559
8 Cover O-ring - SFY (Fluoroelastomer) 9612-7323-03 751519 751536 751542 751542
9 - 12 (Seal Parts) Refer to Seal Replacement Parts later in this manual.
13 Nut, Casing / Adapter 9612-7306-01 9612-7306-01 9612-7306-01 9612-7306-01 9612-7306-01
14 Washer, Casing/Adapter 9612-7301-01 9612-7307-01 9612-7307-01 9612-7307-01 9612-7307-01
15 - 28 (Seal Parts) Refer to Seal Replacement Parts later in this manual.
* Other port connections available upon request. Contact Tri-Clover for details.** Smaller impeller sizes available upon request. Contact Tri-Clover for details.
- 6 -
PARTS LISTCL PUMP REPLACEMENT PARTS
KeyNo.
Description
140TCNEMAFrames
180TCNEMAFrames
210TCNEMAFrames
250TCNEMAFrames
280TSCNEMAFrames
320TSCNEMAFrames
PartNumber
PartNumber
PartNumber
PartNumber
PartNumber
PartNumber
29 Adapter 9612-7065-01 9612-7066-01 9612-7067-01 9612-7068-01 9612-7068-02 9612-7069-01
30 Screw, Motor 189888 189888 189888 189888 189888 189888
31 Washer, Motor 189952 189952 189952 189952 189952 189952
32 Seal Guard 7612-7114-01 9612-7075-01 9612-7075-02 7612-7075-03 9612-7075-03 9612-7075-03
33 Screw, Seal Guard 9612-7315-01 9612-7315-01 9612-7315-01 9612-7315-01 9612-7315-01 9612-7315-01
34 Stub Shaft 9612-7032-01 9612-7031-01 9612-7033-01 9612-7034-01 9612-7034-01 9612-7035-01
35 Compression Ring, Threaded 9612-7037-01 9612-7037-02 9612-7037-05 9612-7037-03 9612-7037-03 9612-7037-06
36 Compression Ring 9612-7036-01 9612-7036-02 9612-7036-05 9612-7036-03 9612-7036-03 9612-7036-06
37 Screw, Compression Ring 9612-7314-01 9612-7314-01 9612-7314-02 9612-7314-03 9612-7314-03 9612-7314-03
38 Washer, Compression Ring 9612-7317-01 9612-7317-01 9612-7317-01 9612-7317-01 9612-7317-01 9612-7317-01
39 Pin, Stub Shaft 9612-7311-01 9612-7311-01 9612-7311-01 9612-7311-01 9612-7311-01 9612-7311-01
40 Retaining Ring, Stub Shaft 9612-7313-01 N/A N/A N/A N/A N/A
41 Leg Bracket 483052 480325 480328 480338 480355 N/A
42 Screw, Leg Bracket 180701 189741 189741 180148 180148 N/A
43 Washer, Leg Bracket 180037 180070 180070 189952 189952 N/A
44 Set Screw, Adjustable Leg 180260 180259 180259 180259 180259 N/A
45 Adjustable Leg 483075 483075 483075 483626 483626 N/A
46 Motor Refer to Motor price booklet
47 Stuffing Box (John Crane) Refer to Seal Replacement Parts later in this manual.
48 John Crane Double 8 Seal Refer to Seal Replacement Parts later in this manual.
- 7 -
PARTS LISTCL PUMP REPLACEMENT PARTS
KeyNo.
Description213-215 TC 254-256 TC 284-286 TC 324-365 TSC 405 TSC
Part Number Part Number Part Number Part Number Part Number29 Adapter 9612-7205-03 9612-7205-03 9612-7205-01 9612-7205-02 9612-7205-02
30 Screw, Motor 189888 189888 189888 189797 189797
31 Washer, Motor 189971 189971 189971 189569 189569
32 Seal Guard 9612-7171-01 9612-7171-01 9612-7171-01 9612-7171-01 9612-7171-01
33 Screw, Seal Guard 9612-7315-01 9612-7315-01 9612-7315-01 9612-7315-01 9612-7315-01
34 Stub Shaft 9612-7198-02 9612-7188-02 9612-7186-02 9612-7086-02 9612-7089-02
35 Compression Ring, Threaded 9612-7037-05 9612-7037-03 9612-7037-04 9612-7037-04 9612-7037-06
36 Compression Ring 9612-7036-05 9612-7036-03 9612-7036-04 9612-7036-04 9612-7036-06
37 Screw, Compression Ring 9612-7314-02 9612-7314-03 9612-7314-03 9612-7314-03 9612-7314-03
38 Washer, Compression Ring 9612-7317-01 9612-7317-01 9612-7317-01 9612-7317-01 9612-7317-01
39 Pin, Stub Shaft 9612-7311-01 9612-7311-01 9612-7311-01 9612-7311-01 9612-7311-01
40 Retaining Ring, Stub Shaft 480328 480338 480355 - -
41 Leg Bracket 189741 180148 180148 - -
42 Screw, Leg Bracket 180070 189952 189952 - -
43 Washer, Leg Bracket 180259 180259 180259 - -
44 Set Screw, Adjustable Leg 483075 483626 483626 - -
45 Adjustable Leg 483075 483626 483626 - -
46 Motor Refer to Motor price booklet
47 Stuffing Box (John Crane) Refer to Seal Replacement Parts later in this manual.
48 John Crane Double 8 Seal Refer to Seal Replacement Parts later in this manual.
- 8 -
SEAL REPLACEMENT PARTS - Type DG (External Balanced Seal)
PARTS LIST
KeyNo.
Description
CL2264CL2265CL2284CL3285CL3295
CL4359CL4378CL4387CL4488
CL4311
Part Number Part Number Part Number5* O-Ring - Buna N 9612-7301-01 9612-7301-01 9612-7325-02
5* O-Ring - EPDM 9612-7301-02 9612-7301-02 9612-7325-01
5* O-Ring - SFY (Fluoroelastomer) 9612-7301-03 9612-7301-03 9612-7325-03
9 Screw, Seal Gland 9612-7303-01 9612-7303-01 189643
10 Seal Gland 9612-7008-01 9612-7008-01 9612-7184-01
11* Front & Rear Stationary Seal Gaskets, Buna N 9612-7130-02 9612-7130-02 9612-7321-02
11* Front & Rear Stationary Seal Gaskets, EPDM 9612-7130-01 9612-7130-01 9612-7321-01
11* Front & Rear Stationary Seal Gaskets, SFY 9612-7130-03 9612-7130-03 9612-7321-03
11* Front Gasket, Stationary Seal, PTFE 9612-7130-04 9612-7130-04 9612-7321-04
12* Silicon Carbide Stationary Seal 9612-7000-01 9612-7000-01 9612-7178-01
15* Rotating Seal - Carbon (includes cup) 9612-7115-01 9612-7115-01 9612-7181-01
15* Rotating Seal - SiC (includes cup) 9612-7115-02 9612-7115-02 9612-7181-02
16* Spring 9612-7116-01 9612-7116-01 9612-7182-01
17 Drive Collar 9612-7004-01 9612-7004-01 --
18 Drive Collar - Stainless Steel -- 9612-7009-02 9612-7173-01
19 Pin, Drive Collar -- -- 9612-7319-01
38 Washer, Compression Ring 9612-7317-01 9612-7317-01 9612-7317-01
* Included in seal kits: Buna N - kit number 9612-7118-02. For models CL4311 or CL6410, order 9612-7177-02 Buna N, SiC - kit number 9612-7119-02. For models CL4311 or CL6410, order 9612-7177-05 EPDM - kit number 9612-7118-01. For models CL4311 or CL6410, order 9612-7177-01 EPDM, SiC - kit number 9612-7119-01. For models CL4311 or CL6410, order 9612-7177-04 SFY - kit number 9612-7118-03. For models CL4311 or CL6410, order 9612-7177-03 SFY, SiC - kit number 9612-7119-03. For models CL4311 or CL6410, order 9612-7177-06
- 9 -
PARTS LISTSEAL REPLACEMENT PARTS - Type FG (Water cooled Single Seal)
KeyNo.
DescriptionAll Models
except CL4311CL4311
Part Number Part Number5* O-Ring - Buna N 9612-7301-01 9612-7325-02
5* O-Ring - EPDM 9612-7301-02 9612-7325-01
5* O-Ring - SFY (Fluoroelastomer) 9612-7301-03 9612-7325-03
9 Screw, Seal Gland 9612-7303-01 189643
10 Seal Gland 9612-7008-01 9612-7184-01
11* Front & Rear Stationary Seal Gaskets, Buna N 9612-7130-02 9612-7321-02
11* Front & Rear Stationary Seal Gaskets, EPDM 9612-7130-01 9612-7321-01
11* Front & Rear Stationary Seal Gaskets, SFY 9612-7130-03 9612-7321-03
11* Front Gasket, Stationary Seal, PTFE 9612-7130-04 9612-7321-04
12* Silicone Carbide Seal 9612-7000-01 9612-7000-01
15* Rotating Seal - Carbon (includes cup) 9612-7115-01 9612-7181-01
15* Rotating Seal - SiC (includes cup) 9612-7115-02 9612-7181-02
16* Spring 9612-7116-01 9612-7182-01
18 Drive Collar, Stainless Steel 9612-7009-02 9612-7173-01
19 Pin, Drive Collar 9612-7312-01 9612-7319-01
20* O-ring, Stuffing Box - Buna 9612-7300-01 9612-7300-01
20* O-ring, Stuffing Box - EPDM 9612-7300-02 9612-7300-02
20* O-ring, Stuffing Box - SFY 9612-7300-03 9612-7300-03
21* Single Flush Lip Seal 9612-7117-01 9612-7324-01
22 Stuffing Box 9612-7007-01 9612-7007-01
23 Screw, Stuffing Box 9612-7302-01 9612-7302-01
24 Flush Pipe 9612-7129-01 9612-7129-01
38 Washer, Compression Ring 9612-7317-01 9612-7317-01
50* Seal Installation Tool 9612-7320-02 9612-7320-03
* Included in seal kits: Buna N - kit number 9612-7118-08. For models CL4311 or CL6410, order 9612-7177-08 Buna N, SiC - kit number 9612-7119-08. For models CL4311 or CL6410, order 9612-7177-11 EPDM - kit number 9612-7118-07. For models CL4311 or CL6410, order 9612-7177-07 EPDM, SiC - kit number 9612-7119-07. For models CL4311 or CL6410, order 9612-7177-10 SFY - kit number 9612-7118-09. For models CL4311 or CL6410, order 9612-7177-09 SFY, SiC - kit number 9612-7119-09. For models CL4311 or CL6410, order 9612-7177-12
SEAL REPLACEMENT PARTS - Type EG (Water cooled, Balanced Double Seal)
PARTS LIST
KeyNo.
DescriptionAll Models except
CL4311 or CL6410**
Part Number5* O-Ring - Buna N 9612-7301-01
5* O-Ring - EPDM 9612-7301-02
5* O-Ring - SFY (Fluoroelastomer) 9612-7301-03
9 Screw, Seal Gland 9612-7303-01
10 Seal Gland 9612-7008-01
11* Front & Rear Stationary Seal Gaskets, Buna N 9612-7130-02
11* Front & Rear Stationary Seal Gaskets, EPDM 9612-7130-01
11* Front & Rear Stationary Seal Gaskets, SFY 9612-7130-03
11* Front Gasket, Stationary Seal, PTFE 9612-7130-04
12* Silicone Carbide Stationary Seal 9612-7000-01
15* Carbon Rotating Seal (includes cup), Buna N and EPDM 9612-7115-01
15* Silicone Carbide Rotating Seal (includes cup), Buna N, SiC and EPDM, SiC 9612-7115-02
16* Spring 9612-7116-01
20* O-ring, Stuffing Box - Buna 9612-7300-01
20* O-ring, Stuffing Box - EPDM 9612-7300-02
20* O-ring, Stuffing Box - SFY 9612-7300-03
23 Screw, Stuffing Box 9612-7302-01
24 Flush Pipe 9612-7129-01
25 Spacing Ring 9612-7006-01
26* Stationary Seal, Rear, SiC 9612-7113-01
26* Stationary Seal, Rear, Stainless Steel 9612-7113-02
27* O-Ring, Stationary Seal, Buna 9612-7316-02
27* O-Ring, Stationary Seal, EPDM 9612-7316-01
27* O-Ring, Stationary Seal, SFY (fluoroelastomer) 9612-7316-03
28 Stuffing Box 9612-7111-01
38 Washer, Compression Ring 9612-7317-01
50* Seal Installation Tool 9612-7320-02
* Included in seal kits: Buna N - kit number 9612-7118-05, Buna N, SiC - kit number 9612-7119-05 EPDM - kit number 9612-7118-04, EPDM, SiC - kit number 9612-7119-04. SFY (Fluoroelastomer) - kit number 9612-7118-06, SFY (Fluoroelastomer), SiC - kit number 9612-7119-06** Consult Tri-Clover for a model CL4311 or CL6410 with a type EG seal.
PARTS LIST
SEAL REPLACEMENT PARTS - JOHN CRANE DOUBLE 8 SEAL
KeyNo.
DescriptionAll Models except
CL4311 or CL6410
Part Number9 Screw, Seal Gland 9612-7303-01
10 Seal Gland 9612-7008-01
11* Front & Rear Stationary Seal Gaskets, Buna N 9612-7130-02
11* Front & Rear Stationary Seal Gaskets, EPDM 9612-7130-01
12* Silicone Carbide Stationary Seal 9612-7000-01
20* O-ring, Stuffing Box - Buna 9612-7300-01
20* O-ring, Stuffing Box - EPDM 9612-7300-02
20* O-ring, Stuffing Box - SFY 9612-7300-03
26* Stationary Seal, Rear, SiC 9612-7113-01
26* Stationary Seal, Rear, Stainless Steel 9612-7113-02
27* O-Ring, Stationary Seal, Buna 9612-7316-02
27* O-Ring, Stationary Seal, EPDM 9612-7316-01
27* O-Ring, Stationary Seal, SFY (fluoroelastomer) 9612-7316-03
47 Stuffing Box 9612-7111-02
48 John Crane Double Seal Type 8B2 - Viton 9612-7318-01
48 John Crane Double Seal Type 8B2 - EPDM 9612-7318-02
* Included in seal kits: Buna N - kit number 9612-7118-05, Buna N, SiC - kit number 9612-7119-05 EPDM - kit number 9612-7118-04, EPDM, SiC - kit number 9612-7119-04. SFY (Fluoroelastomer) - kit number 9612-7118-06, SFY (Fluoroelastomer), SiC - kit number 9612-7119-06
PARTS LIST