PARTS LIST · 2018-01-15 · 2 aluminum tapes driver’s dashboard lower cover opening puddle light...
Transcript of PARTS LIST · 2018-01-15 · 2 aluminum tapes driver’s dashboard lower cover opening puddle light...
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2017 American Honda Motor Co., Inc. – All Rights Re
VERSION 1
PUDDLE LIGHTSP/N 08V27-TVA-100
served. AII06720-26 (171
2018 ACCORD
0)
Issue Date
OCT 2017
PARTS LISTPuddle light harness A
2 Puddle light harnesses B
2 Lights
2 Light trims
24 Wire ties(Some may not be used)
Wire tie with clip A
6 Wire ties with clip B(Some may not be used)
Fuse label
4 Self-tapping screws
6 Aluminum tapes(Some may not be used)
Urethane tape
2 EPT sealers
1 of 2508V27-TVA-1000-90
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriverSteel wireDrillFilePushpinHacksaw3 mm and 6 mm Drill bits15 mm Hole sawEye protection (face shield, safety goggles, etc.)Diagonal cutters10 mm Open end wrenchIsopropyl alcoholScissorsShop towelRulerMasking tapeThe following tools are available through the Honda Tool and Equipment Program. On the iN, click on Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857.• Trim Tool Set (T/N SOJATP2014)• Plastic Trim Tool (T/N SILTRIMTL10)
Illustration of the Puddle Lights on the Vehicle
PUDDLE LIGHT HARNESS B
PUDDLE LIGHT HARNESS A
PUDDLE LIGHT HARNESS B
LIGHT
2A FUSE
LIGHT
2 of 25 AII06720-2
INSTALLATION
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
NOTE: If the vehicle has accessory side under spoilers, follow the same procedure.1. Disconnect the negative cable from the battery.2. Remove the passenger’s dashboard under cover.
PASSENGER’S DASHBOARD UNDER COVERCLIP 2 CLIPS
6 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
3. Remove the passenger’s door sill trim.
4 CLIPS
PASSENGER’S DOOR SILL TRIM
3 RETAINING TABS
4. Pull away the door opening seal and remove the passenger’s kick panel.
2 CLIPS
PASSEN-GER’S KICK
DOOR OPENING SEAL(Pull away.)
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-2
5. Remove the driver’s dashboard lower cover and unplug the vehicle connectors.
DRIVER’S DASHBOARD LOWER COVER
8 CLIPS
VEHICLE CONNECTORS
6. Remove the driver’s door sill trim.
4 CLIPS
DRIVER’S DOOR SILL TRIM
3 RETAINING TABS
6 (1710) 3 of 25
7. Pull away the door opening seal and remove the driver’s kick panel.
2 CLIPS
DRIVER’S KICK PANEL
DOOR OPENINGSEAL(Pull away.)
8. Lower and pull out the steering wheel as shown.
UPPER COLUMN COVER
STEERING WHEEL
MASKING TAPE
9. Apply masking tape to the upper column cover.
4 of 25 AII06720-2
10. Connect the negative cable to the battery, then turn the ignition to ON. Turn the steering wheel 90° counterclockwise. Using a plastic trim tool, release the upper column cover.
PLASTIC TRIM TOOL
UPPER COLUMN COVER
STEERING WHEEL
90° counterclockwise.
UPPER COLUMN COVER
6 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
11. Turn the steering wheel 180° clockwise. Using a plastic trim tool, release the upper column cover.
PLASTIC TRIM TOOL
UPPER COLUMN COVER
STEERING WHEEL
180° clockwise.
UPPER COLUMN COVER
12. Release the upper column cover, and secure it to the dashboard with masking tape.
UPPER COLUMN COVER
DASHBOARD MASKING TAPE
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-2
13. Remove the self-tapping screw from the lower column cover.
LOWER COLUMN COVER
SELF-TAPPING SCREW
14. Turn the steering wheel 180° counterclockwise, and remove the other self-tapping screw from the lower column cover.
STEERING WHEEL
LOWER COLUMN COVER
SELF-TAPPING SCREW
180° counterclockwise.
6 (1710) 5 of 25
15. Remove the lower column cover.
LOWER COLUMN COVER
SELF-TAPPING SCREW
16. Turn the steering wheel fully counterclockwise.
LEFT FRONT INNER FENDER
3 SELF-TAPPING SCREWS
17. Remove the three self-tapping screws from the left front inner fender.
6 of 25 AII06720-2
18. Remove the four clips from the left side sill trim.
4 CLIPS
LEFT SIDE SILL TRIM
19. Remove the left side sill trim as shown.
LEFT SIDE SILL TRIM(Slide forward and remove.)
6 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
20. Remove the 13 clips from the vehicle panel.
13 CLIPS
VEHICLE PANEL
45°
21. Turn the steering wheel fully clockwise, and repeat steps 17 through 20 on the right side of the vehicle.
22. Turn the ignition to OFF, then disconnect the negative cable from the battery.
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-2
23. Using isopropyl alcohol on a shop towel, thoroughly clean the fuse case where the fuse label will attach. Attach the fuse label (2A PUDDLE LIGHT) to the fuse case on puddle light harness A.
Clean with isopropyl alcohol.
FUSE LABEL(2A PUDDLE LIGHT) FUSE CASE
PUDDLE LIGHT HARNESS A
6 (1710) 7 of 25
If the vehicle is equipped with accessory illuminated door sill trims, go to step 25; if the vehicle is equipped with accessory ambient lights, go to step 27; if the vehicle is equipped with another accessory, go to step 28; otherwise, continue with step 24.
Without another accessory24. Plug the puddle light harness A 6-pin connector into
the vehicle 6-pin connector. Secure the puddle light harness A 6-pin connector to the vehicle 20-pin connector as shown. Go to step 29.
PUDDLE LIGHT HARNESS A 6-PIN CONNECTOR
VEHICLE 6-PIN CONNECTOR
FUSE BOX
VEHICLE 20-PIN CONNECTOR
PUDDLE LIGHT HARNESS A 6-PIN CONNECTOR
8 of 25 AII06720-2
With accessory illuminated door sill trims25. Unplug the accessory illuminated door sill trim
harness 6-pin connector, and plug the puddle light harness A 6-pin connector into the vehicle 6-pin connector. Secure the puddle light harness A 6-pin connector to the vehicle 20-pin connector as shown.
ACCESSORY ILLUMINATED DOOR SILL TRIM HARNESS 6-PIN CONNECTOR
PUDDLE LIGHT HARNESS 6-PIN CONNECTOR
DUMMY CONNECTOR(Do not reuse.)VEHICLE
6-PIN CONNECTOR
PUDDLE LIGHT HARNESS A 6-PIN CONNECTOR
VEHICLE 20-PIN CONNECTOR
PUDDLE LIGHT HARNESS A 6-PIN CONNECTOR
ACCESSORY ILLUMINATED DOOR SILL TRIM HARNESS 6-PIN CONNECTOR
FUSE BOX
26. Remove the dummy connector from the puddle light harness A 6-pin connector. Plug the accessory illuminated door sill trim harness 6-pin connector into that connector. Go to step 29.
6 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
With accessory ambient lights27. Plug the puddle light harness A 6-pin connector into
the accessory ambient light harness 6-pin connector. Secure the puddle light harness A 6-pin connector to the accessory ambient light harness 6-pin connector as shown. Go to step 29.
ACCESSORY AMBIENT LIGHT HARNESS 6-PIN CONNECTOR
PUDDLE LIGHT HARNESS A 6-PIN CONNECTOR
FUSE BOX
PUDDLE LIGHT HARNESS A 6-PIN CONNECTOR
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-2
With another accessory28. Remove the dummy connector from the other
accessory harness 6-pin connector, and plug the puddle light harness A 6-pin connector into that connector. Secure the puddle light harness A 6-pin connector to the vehicle 20-pin connector as shown.
OTHER ACCESSORY HARNESS 6-PIN CONNECTOR
PUDDLE LIGHT HARNESS A 6-PIN CONNECTOR
VEHICLE 20-PIN CONNECTOR
PUDDLE LIGHT HARNESS A 6-PIN CONNECTOR
FUSE BOX
DUMMY CONNECTOR(Do not reuse.)
6 (1710) 9 of 25
29. Route puddle light harness A along the vehicle harness, and secure it and the fuse case to the vehicle harness with three wire ties.
PUDDLE LIGHT HARNESS A
VEHICLE HARNESS
2 WIRE TIES
GREEN TAPE
FUSE CASE
FUSE BOX
VEHICLE HARNESS
WIRE TIE
PUDDLE LIGHT HARNESS A
10 of 25 AII06720-2
30. Route puddle light harness A along the vehicle harness, and secure it to the vehicle harness with two wire ties.
2 WIRE TIES
DRIVER’S KICK PANEL OPENING
PUDDLE LIGHT HARNESS A VEHICLE
HARNESS
URETHANE TAPE(Cut in half.) PUDDLE LIGHT
HARNESS A 2-PIN CONNECTOR
31. Using scissors, cut one urethane tape in half, and attach one piece around the puddle light harness A 2-pin connector.
6 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
32. Route puddle light harness A as shown, and secure it to the vehicle bracket with one wire tie with clip A. If the vehicle is already equipped with the another accessory harness, using diagonal cutters, cut the clip portion off of one wire tie with clip A. Secure puddle light harness A to the other accessory harness with one wire tie with clip A.
PUDDLE LIGHT HARNESS A
DRIVER’S DASHBOARD LOWER COVER OPENING
VEHICLE BRACKET
WIRE TIE WITH CLIP A
EDGE OF THE URETHANE TAPE
PUDDLE LIGHT HARNESS A
EDGE OF THE URETHANE TAPE
WITH OTHER ACCESSO-RY HARNESS
OTHER ACCESSORY HARNESS
Cut off.
WIRE TIE WITH CLIP A
WIRE TIE WITH CLIP A CLIP
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-2
If the vehicle is equipped with another accessory harness, go to step 37; otherwise, continue with step 33.
Without another accessory harness33. Secure puddle light harness A to the vehicle harness
and vehicle bracket with two wire ties as shown.
PUDDLE LIGHT HARNESS A
VEHICLE BRACKET
WIRE TIE
LOCK PORTION
SECTION VIEW
FRONT
VEHICLE BRACKET
WIRE TIE PUDDLE LIGHT HARNESS A
FUSE BOX VEHICLE HARNESS
WIRE TIE
PUDDLE LIGHT HARNESS A
6 (1710) 11 of 25
34. Temporarily place two pieces of aluminum tape on the knee airbag over puddle light harness A. Using scissors, cut off the excess aluminum tape as shown.
KNEE AIRBAG
2 ALUMINUM TAPES
DRIVER’S DASHBOARD LOWER COVER OPENING
PUDDLE LIGHT HARNESS A
Line up.
2 ALUMINUM TAPES
PUDDLE LIGHT HARNESS A
2 LABELS
Cut off the excess.
2 ALUMINUM TAPES
KNEE AIRBAG COVER(Do not cover.)
2 LABELS(Do not cover.)
SECTION VIEW
KNEE AIRBAG COVER
12 of 25 AII06720-2
35. Using isopropyl alcohol on a shop towel, thoroughly clean the knee airbag where the aluminum tape will attached.
KNEE AIRBAG
2 ALUMINUM TAPES
DRIVER’S DASHBOARD LOWER COVER OPENING
Clean withisopropyl alcohol.
PUDDLE LIGHT HARNESS A
Line up.
2 ALUMINUM TAPES
PUDDLE LIGHT HARNESS A
2 LABELS
2 ALUMINUM TAPES
KNEE AIRBAG COVER(Do not cover.)
2 LABELS(Do not cover.)
SECTION VIEW
KNEE AIRBAG COVER
36. Secure puddle light harness A to the knee airbag with two pieces of aluminum tape as shown. Go to step 41.
6 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
With another accessory harness37. Cut off the wire tie from the other accessory harness.
Secure puddle light harness A and the other accessory harness to the vehicle harness and vehicle bracket with two wire ties as shown.
PUDDLE LIGHT HARNESS A VEHICLE
BRACKET
WIRE TIE
LOCK PORTION
SECTION VIEW
FRONT
WIRE TIE(Cut off.)
WIRE TIEPUDDLE LIGHT HARNESS A
FUSE BOX VEHICLE HARNESS
WIRE TIE
PUDDLE LIGHT HARNESS A
OTHER ACCESSORY HARNESS
OTHER ACCESSORY HARNESS
VEHICLE BRACKET
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-2
38. Temporarily place two pieces of aluminum tape on the knee airbag over puddle light harness A and the other accessory harness. Using scissors, cut off the excess aluminum tape as shown.
KNEE AIRBAG
2 ALUMINUM TAPES
DRIVER’S DASHBOARD LOWER COVER OPENING
PUDDLE LIGHT HARNESS A
Line up.
PUDDLE LIGHT HARNESS A
2 LABELS
Cut off the excess.
2 ALUMINUM TAPES
KNEE AIRBAG COVER(Do not cover.)
2 LABELS(Do not cover.)
SECTION VIEWKNEE
AIRBAG COVER
OTHER ACCESSORY HARNESS
OTHER ACCESSORY HARNESS
2 ALUMINUM TAPES
6 (1710) 13 of 25
39. Using isopropyl alcohol on a shop towel, thoroughly clean the knee airbag where the aluminum tape will attached.
KNEE AIRBAG
2 ALUMINUM TAPES
DRIVER’S DASHBOARD LOWER COVER OPENING
Clean withisopropyl alcohol.
Line up.
PUDDLE LIGHT HARNESS A
2 LABELS
2 ALUMINUM TAPES
KNEE AIRBAG COVER(Do not cover.)
2 LABELS(Do not cover.)
SECTION VIEW
KNEE AIRBAG COVER
PUDDLE LIGHT HARNESS A
OTHER ACCESSORY HARNESS
2 ALUMINUM TAPES
OTHER ACCESSORY HARNESS
40. Secure puddle light harness A to the knee airbag with two pieces of aluminum tape as shown.
14 of 25 AII06720-2
41. Route the piece of steel wire, and slide it up as shown.
PASSENGER’S DASHBOARD LOWER COVER OPENING
STEEL WIRE
STEEL WIRE
STEEL WIRE(Slide.)
STEEL WIRE
6 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
42. Attach the steel wire to puddle light harness A with masking tape as shown.
PUDDLE LIGHT HARNESS ASTEEL WIRE
MASKING TAPE
43. Route puddle light harness A. Remove the masking tape and steel wire.
PASSENGER’S DASHBOARD LOWER COVER OPENING
PUDDLE LIGHT HARNESS A STEEL WIRE
MASKING TAPE
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-2
44. Route puddle light harness A as shown, and secure it to the vehicle frame at the green tape on puddle light harness A with one wire tie.
PUDDLE LIGHT HARNESS A
PASSENGER’S DASHBOARD UNDER COVER OPENING
VEHICLE FRAME
2 WIRE TIES
GREEN TAPE
VEHICLE FRAME
VEHICLE HARNESS
WIRE TIE
PUDDLE LIGHT HARNESS A
45. Secure puddle light harness A to the vehicle frame and vehicle harness with two wire ties.
6 (1710) 15 of 25
46. Route puddle light harness A as shown, and secure it to the vehicle harness and vehicle frame with three wire ties.
PASSENGER’S DASHBOARD UNDER COVER OPENING
PUDDLE LIGHT HARNESS A
VEHICLE HARNESS
WIRE TIE
VEHICLE FRAME
VEHICLE HARNESS
PUDDLE LIGHT HARNESS A
2 WIRE TIES
16 of 25 AII06720-2
47. Route puddle light harness A along the vehicle harness, and secure it to the vehicle harness with one wire tie.
PASSENGER’S KICK PANEL OPENING
PUDDLE LIGHT HARNESS A
VEHICLE HARNESS
WIRE TIE
PUDDLE LIGHT HARNESS A2-PIN CONNECTOR
URETHANE TAPE(Cut in step 31.)
48. Attach one piece of urethane tape cut in step 31 around the puddle light harness A 2-pin connector.
6 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
49. Pull away the door opening seal, and peel back the floor carpet.
FLOOR CARPET(Peel back.) CLIP
DOOR OPENING SEAL(Pull away.)
50. Remove the two vehicle grommets from the vehicle panel, and route a piece of steel wire as shown.
2 VEHICLE GROMMETS(Do not reuse.)
VEHICLE PANEL
VEHICLE PANEL
STEEL WIRE
LEFT FRONT TIRE
FRONT
OPPOSITE SIDE VIEWVEHICLE GROMMET
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-2
51. Attach the steel wire to the puddle light harness B with masking tape as shown.
PUDDLE LIGHT HARNESS B STEEL
WIREMASKING TAPE
PUDDLE LIGHT HARNESS B
52. Route puddle light harness B. Remove the masking tape and steel wire.
STEEL WIRE
MASKING TAPE
PUDDLE LIGHT HARNESS B
6 (1710) 17 of 25
53. Push the grommet on puddle light harness B into the vehicle panel hole, and wrap it EPT sealer as shown.
PUDDLE LIGHT HARNESS B
GROMMET(Push into the vehicle panel hole.)
FRONT
OPPOSITE SIDE VIEW
VEHICLE PANEL HOLE
PUDDLE LIGHT HARNESS B
GREEN TAPEEPT SEALER
(Line up with the green tape.)
18 of 25 AII06720-2
54. Route puddle light harness B wrapped with the EPT sealer as shown, and secure the grommet to the vehicle panel hole.NOTE:• Install puddle light harness B by holding the
grommet.• Make sure that the grommet is seated properly.
VEHICLE PANEL HOLE
40 mm(1.57 in.)
PUDDLE LIGHT HARNESS B
EPT SEALER
VEHICLE PANEL HOLE
VEHICLE PANEL
GROMMET
FRONT
GROMMET
PUDDLE LIGHT HARNESS B
SECTION VIEW
6 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
55. Route puddle light harness B along the vehicle harness. Plug the puddle light harness B 2-pin connector into the puddle light harness A 2-pin connector, and secure the 2-pin connectors to the vehicle harness with one wire tie as shown.
VEHICLE HARNESS
WIRE TIE
PUDDLE LIGHT HARNESS B2-PIN CONNECTOR
PUDDLE LIGHT HARNESS A 2-PIN CONNECTOR
2-PIN CONNECTORS
VEHICLE PANEL
SECTION VIEW
FRONT
WIRE TIE
2-PIN CONNECTORS
VEHICLE HARNESS
Line up.VEHICLE PANEL
2 WIRE TIES
VEHICLE HARNESS
SECTION VIEW
LOCK PORTION
VEHICLE PANEL
2 WIRE TIES
VEHICLE HARNESS
PUDDLE LIGHT HARNESS B
VEHICLE CONNECTORS
56. Secure puddle light harness B to the vehicle harness with two wire ties as shown.
57. Repeat steps 49 through 56 on the right side of the vehicle.
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-2
58. Using a pushpin, pierce the inside of the left side sill trim through the center of six scribe marks.NOTE: Make sure to pierce perpendicular to the left side sill trim.
PUSHPIN(Pierce perpendicular.): 6 MARKS
6 SCRIBE MARKS
LEFT SIDE SILL TRIM
LEFT SIDE SILL TRIM(inside)
6 (1710) 19 of 25
59. While wearing eye protection, drill the six pierced marks on the left side sill trim with a 3 mm drill bit.NOTE: Make sure to drill perpendicular to the left side sill trim.
: 6 MARKS LEFT SIDE SILL TRIM
LEFT SIDE SILL TRIM(outside)
DRILL(Drill perpendicular.)
3 mm DRILL BIT
20 of 25 AII06720-2
60. While wearing eye protection, enlarge the 3 mm holes on the left side sill trim with a 6 mm drill bit. Remove any burrs.NOTE:• Make sure to drill the correct positions.• Make sure to drill perpendicular to the left side
sill trim.
LEFT SIDE SILL TRIM
: 2 HOLES LEFT SIDE SILL TRIM
6 mm DRILL BIT
DRILL(Drill perpendicular.)
6 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
61. While wearing eye protection, enlarge the 3 mm holes on the left side sill trim with a 15 mm hole saw.NOTE:• Make sure to drill the correct positions.• Make sure to drill perpendicular to the left side
sill trim.
LEFT SIDE SILL TRIM
: 4 HOLES LEFT SIDE SILL TRIM
15 mm HOLE SAW
DRILL(Drill perpendicular.)
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-2
62. Using a hacksaw, cut out the left side sill trim as shown. Remove any burrs.
CUTTING AREA
SCRIBE LINE
Cut out.
LEFT SIDE SILL TRIM(inside)
63. Install the light and light trim to the left side sill trim with two self-tapping screws.
LEFT SIDE SILL TRIM
LIGHT
LIGHT TRIM
2 SELF-TAPPING SCREWS
6 (1710) 21 of 25
64. Install one wire tie to the light 2-pin connector, and secure the light 2-pin connector to the clip base on the left side sill trim with one wire tie.
WIRE TIE LEFT SIDE SILL TRIM CLIP BASE
LIGHT 2-PIN CONNECTOR
LEFT SIDE SILL TRIM
22 of 25 AII06720-2
If the vehicle is equipped with accessory side under spoilers, go to step 71; otherwise, continue with step 65.
Without accessory side under spoilers65. Plug the puddle light harness B 2-pin connector into
the light 2-pin connector. Secure puddle light harness B to the clip base on the left side sill trim with one wire tie.
PUDDLE LIGHT HARNESS B 2-PIN CONNECTOR
PUDDLE LIGHT HARNESS B
LIGHT 2-PIN CONNECTOR
WIRE TIE
CLIP BASE
Clean with isopropyl alcohol.
2 ALUMINUM TAPES
PUDDLE LIGHT HARNESS B
2 ALUMINUM TAPES
LEFT SIDE SILL TRIM
FRONT VIEW
SCRIBE LINE
Line up.LEFT SIDE SILL TRIM
Line up.
SCRIBE LINE
66. Using isopropyl alcohol on a shop towel, thoroughly clean the left side sill trim where the aluminum tape will attach. Secure puddle light harness B to the left side sill trim with two pieces of aluminum tape as shown.
6 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
67. Install the 13 clips removed in step 20 to the left side sill trim.
13 CLIPS
LEFT SIDE SILL TRIM
68. To prevent damage from hitting the doors while installing, apply masking tape to the left side sill trim.
MASKING TAPE
LEFT SIDE SILL TRIM
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-2
69. Install the left side sill trim to the vehicle. Remove the masking tape.NOTE: Make sure that puddle light harness B is not pinched.
LEFT SIDE SILL TRIM
PUDDLE LIGHT HARNESS B(Do not pinch.)
70. Repeat steps 58 through 69 on the right side of the vehicle. Go to step 76.
6 (1710) 23 of 25
With accessory side under spoilers71. Plug the puddle light harness B 2-pin connector into
the light 2-pin connector.
LIGHT 2-PIN CONNECTOR
PUDDLE LIGHT HARNESS B 2-PIN CONNECTOR
ACCESSORY LEFT SIDE UNDER SPOILER
3 RIBS
ACCESSORY LEFT SIDE UNDER SPOILER
PUDDLE LIGHT HARNESS B
3 WIRE TIES WITH CLIP B
72. Secure the puddle light harness B to the ribs on the accessory left side under spoiler with three wire ties with clip B.
24 of 25 AII06720-2
73. Apply masking tape to the accessory left side under spoiler as shown.NOTE: Do not damage the left side under spoiler with the door edge.
MASKING TAPE
ACCESSORY LEFT SIDE UNDER SPOILER
74. Install the accessory left side under spoiler to the vehicle. Remove the masking tape.NOTE:• Refer to the accessory side under spoilers
Installation Instructions for additional information.
• Make sure that puddle light harness B is not pinched.
ACCESSORY LEFT SIDE UNDER SPOILERPUDDLE LIGHT
HARNESS B(Do not pinch.)
13 CLIPS
75. Repeat steps 58 through 74 on the right side of the vehicle.
6 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
76. Check that all wire harnesses are routed properly and all connectors are plugged in.
77. Install all removed parts.78. Connect the negative cable to the battery.79. Press and hold the audio unit power button for 2
seconds to restore the audio and navi (if equipped) system functions.
80. Set the clock on vehicles without navigation.81. If necessary, restore the systems back to normal
operation as described in the service information.
Check the Operation of the Puddle Lights82. Make sure the light comes on when you open each
door.
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-2
6 (1710) 25 of 25