PARTS CATALOG - Northern Lights...2010/02/18 · 10 R501124 2 Screw, M12 x 61 mm - 11 RE65908 4...
Transcript of PARTS CATALOG - Northern Lights...2010/02/18 · 10 R501124 2 Screw, M12 x 61 mm - 11 RE65908 4...
P1064-3For Models: NL1064T23, NL1064H23, NL1064H33,
and NL1064H43
PARTS CATALOG
Marine Generators | Marine Diesel Engines | Land-Based Generators
Diesel engine exhaust and some of its constitu-ents are known to the State of California to cause
cancer, birth defects, and other reproductive harm.
— CALIFORNIA —Proposition 65 Warning:
Northern Lights4420 14th Avenue N.W.Seattle, WA 98107Tel: (206) 789-3880Fax: (206) 782-5455
Copyright ©2015 Northern Lights, Inc.All rights reserved. Northern Lights™, andthe Northern Lights logo are trademarks ofNorthern Lights, Inc.
Printed in U.S.A.PART NO.: P1064 06/15
P1064-3 06/15
I
PARTS CATALOG for Models
NL1064T23, NL1064H23, NL1064H33, and NL1064H43
Proprietary InformationThis publication is the property of Northern Lights, Inc.
It may not be reproduced in whole or in part without the written permission of Northern Lights, Inc.© Northern Lights, Inc. All rights reserved. Litho U.S.A. Publication number P1064-3 06/15
GROUP 3 - COOLING SYSTEM
Coolant Pump Inlet & Assembly ............................0- 1
Thermostat ..............................................................2- 6
Engine Oil Cooler .............................................7- 8
Idler Shaft Assembly ............................................ 9 -10
Radiator .............................................................. 16- 13
GROUP 4 - FUEL SYSTEM
Fuel Injection Pump & Fuel Lines ......................0- 5
Fuel Filters and Lines .......................................6- 17
Fuel Transfer Pump .........................................18-19
Fuel Filter & Spearator ............................................. 20
Push on Fuel Lines .................................................... 21
GROUP 5 - ELECTRICAL SYSTEM
12 & 24 Volt, Standard & Isolated Ground ...........0- 3
Wire Harness ...........................................................4- 7
Engine Sensors .................................................8- 9
Alternators and Mounting ..............................10- 12
Drive Belt .................................................................. 13
Control Panels ........................................................... 15
GROUP 8 - FRAMES & MOUNTING
Base Frames ............................................................0- 3
GROUP 1 - ENGINE
Cylinder Block Assembly .................................0-1
Flywheel Housing ........................................2- 6
Crankshaft & Main Bearings .............................. 7
Crankshaft Pulley ..........................................8- 9
Cylinder Liner Assembly & Connecting Rod ....11- 12
Timing Cover Plate ................................... 13- 14
Camshaft ............................................................15
Balance Shaft ...............................................16- 17
Timing Cover ...............................................18- 23
Oil Filter Assembly, Mounting, & Adapter ............24
Oil Pump ................................................................... 25
Oil Pan ............................................................... 26- 27
Oil Drain & Dipstick ................................................. 28
Cylinder Head, Head Gasket, Valves ............. 30- 35
Rocker Cover, Rocker Shaft, Rocker Arm ......... 36- 40
Ventilating System ............................................ 41 - 42
GROUP 2 - INTAKE & EXHAUST
Air Intake & Air Filter ...........................................1 - 9
Turbocharger ..................................................... 10 - 13
Exhaust Manifold & Adapter ............................ 14 - 16
Exhaust Elbows & Adapter ............................... 17 - 21
Please read thoroughly before att empting to use this manual:Table of Content ...................................................................................................................................................IModel Designation & Serial Numbers .................................................................................................... IIReading a Parts Page ........................................................................................................................... III
Table of Contents
P1064-3 06/15
MODEL DESIGNATION
II
L - M - NL
L - Lugger propulsion unitM - Northern Lights marine generator setNL - Northern Lights industrial generator set
Base Model #(Deere 4045 Powertech
Series engine block)
AspirationD NaturalT Turbocharged
NORTHERN LIGHTSYour set has three serial numbers: 1 an engine number stamped on the block, 2 a generator plate, and 3 a generator set plate. Use the serial number on the generator set plate when ordering parts or in correspondence. The generator set plate is found on the service side of the generator and resembles one of the drawings below.
Refer to the category designations below to fi nd the correct parts pages for your model.
SERIAL NUMBERS
Generator Set Serial Number
Northern Lights turbocharged marine diesel generator set with a John Deere 4045 engine.
M 1064 T
INTRODUCTION
1064 T - H
A AftercooledH High OutputC Commercial
Northern Lights turbocharged marine diesel generator set with a John Deere 4045 engine, aftercooled.
M 1064 A
Northern Lights turbocharged high output marine diesel generator set with a John Deere 4045 engine.
All model numbers in parentheses will indicate a John Deere base engine. All variations requiring serial numbers for proper identifi cation will be noted as ADE or John Deere.
Northern Lights industrial diesel engine, with a John Deere 4045 engine.NL 1064
M 1064 H
Generator Set Serial NumberLugger Serial Number
=
=
=
=
P1064-3 06/15
REFERENCES:1. Grouping section title. 7. Quantity of parts used.2. Model designation of equipment that uses parts 8. Description of each component part. listed on this page. 9. Serial number of unit the part fi ts.3. Title and description of assembly. 10. Assembly or kit designated by Key 0 or ••/•.4. Drawing numbers that correspond to key 11. Grouping index number. column numbers for parts identifi cation. 12. Page number within the grouping index.5. Key column for locating parts shown on drawing. 13. Manual title.6. Part number. 14. Page publication date.
NOTE: Arrows always point toward the front of the engine.
III
ELECTRICAL SYSTEM1
READING A PARTS PAGEIMPORTANT:
Before selecting parts, be sure that you are choosing parts from the correct page.Check the model designation at the page top.Do not use this illustration for parts purchasing.
4 23
5
7 8 9
P445 06/00
5-2
0 185046210 1 Alternator Assembly -1 185446219 1 Flywheel, complete -2 185446217 1 Plate, complete -3 185716200 1 Plate -4 185446218 1 Stator, complete -5 040126210 2 Bearing -6 020210010 1 Nut -7 027100010 1 Spring washer -8 026100010 1 Washer -9 185446220 1 Clamp -10 015140408 1 Screw -11 015140425 2 Screw -12 199236510 1 Collar -
6
ALTERNATOR ASSEMBLY: M - NL445
14
1211
13
10
KEY PART NUMBER QTY. DESCRIPTION SERIALNUMBER
INTRODUCTION
P1064-3 06/15
1 - 0
GROUP 1 – ENGINE
Cylinder Block
Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved. RE531746PCDA01
NL1064T23, NL1064H23, NL1064H33, & NL1064H43
P1064-3 06/15
1 - 1
GROUP 1 – ENGINE
Cylinder Block
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
•• RE536158 1 Cylinder Short Block NL1064T23 - •• RE532716 1 Cylinder Short Block NL1064H23, NL1064H33 - •• RE536966 1 Cylinder Short Block NL1064H43 - 1 1 Cylinder Block (marked R504849) - 2 RE508185 2 Plug, 1-1/4” O-ring Port (1-5/8-12) - 3 U13639 1 O-ring - 7 R48685 4 Dowel Pin - 8 R116466 1 Plug - 9 R119874 1 Bushing (also order TY6333) - 10 R26650 2 Dowel Pin - 11 T18891 2 Plug (16 mm O.D.) - 12 R115299 6 Bushing - 13 RE505501 1 Bleed Valve - 14 RE63674 1 Valve Kit - 15 T20168 10 Washer - 16 T23474 10 Capscrew, 1/2 x 3-3/4” - 17 R97185 1 O-ring - 18 15H695 1 Pipe Plug 3/8” x 18 NPT - 19 R131182 4 Orifi ce - 20 RE42713 5 Pipe Plug 1/8” x 27 NPT - 21 15H584 1 Pipe Plug 1/2” x 14 NPT - 22 AT13740 1 Drain Valve 1/4” x 18 NPT (NL1064T23) - RE507807 1 Pipe Plug, 1/4” x 18 NPT (with pre-applied sealant, NL1064H33 & NL1064H43) - 23 T18891 1 Plug, 16 mm OD (NL1064H43) -
NL1064T23, NL1064H23, NL1064H33, & NL1064H43
P1064-3 06/15
1 - 2
GROUP 1 – ENGINE
Flywheel Housing SAE #4
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R503447 1 Housing - 2 AR106083 1 Plug - 3 R131765 1 Plug - 4 R61467 1 O-ring - 5 RE44574 1 Seal - 6 19M7838 4 Capscrew, Hex Head Flanged M12 x 130 - 7 19M8306 1 Capscrew, Hex Head Flanged M12 x 50, Upper Left hand - 19M7813 1 Capscrew, Hex Head Flanged M12 x 45, Upper Right hand 8 R135918 8 Capscrew, Hex Head Flanged M12 x 38 -
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE59302PCDD01
NL1064T23
P1064-3 06/15
1 - 3
GROUP 1 – ENGINE
Flywheel Housing SAE #3
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R503444 1 Housing - 2 R131768 1 Plug - 3 R61467 1 O-ring - 4 RE44574 1 Seal - 5 RE57836 1 Pipe Plug, 1/2”- 14 NPT with pre-applied sealant - 6 19M8306 4 Capscrew, M12 x 50 - 7 R135918 8 Capscrew, Hex Head Flanged M12 x 38 -
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE59342PCDE01
NL1064H33
P1064-3 06/15
1 - 4
GROUP 1 – ENGINE
Flywheel Housing SAE #3
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R502941 1 Housing - 2 R131768 1 Plug - 3 R61467 1 O-ring - 4 RE44574 1 Seal - 5 T13518 1 Plug - 6 RE57836 1 Pipe Plug, 1/2” - 14 NPT with pre-applied sealant - 7 R121039 1 Plate - 8 19M7923 2 Capscrew, M6 x 12 - 9 19M8306 4 Capscrew, M12 x 50 - 10 R135918 8 Bolt, M12 x 38 - 11 R39112 1 Fitting -
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE57610PCDE01
NL1064H43
P1064-3 06/15
1 - 5
GROUP 1 – ENGINE
Flywheel SAE #10
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE58574 1 Flywheel Assembly (includes key #2) - 2 R114282 1 Ring Gear, 142 Teeth - 3 R135918 4 Capscrew, Hex Head Flanged M12 x 38 (not shown) -
NL1064T23
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE59287PCDD01
P1064-3 06/15
1 - 6
GROUP 1 – ENGINE
Flywheel SAE #11-1/2
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE500398 1 Flywheel Assembly (includes key #2) - 2 R28811 1 Ring Gear, 129 Teeth - 3 R135918 4 Bolt, M12 x 38 (not shown) -
NL1064H23, NL1064H33, & NL1064H43
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE59281PCDD01
P1064-3 06/15
1 - 7
GROUP 1 – ENGINE
Crankshaft and Main Bearings
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE506195 1 Crankshaft (marked R503715, includes keys 2, 3, 7. Also order - Front Main Seal #516340 and Rear Main Seal #44574.) - 2 R120631 1 Gear (30 Teeth) - 3 R505609 1 Shaft Key, 18.5 mm - 4 RE65165 4 Main Bearing Kit (Standard) - RE65911 4 Main Bearing Kit (Undersize .254 mm) - 5 RE65168 1 Thrust Bearing Kit (Standard) - RE65912 1 Thrust Bearing (Undersize .254 mm) - 6 R135918 4 Bolt, M12 x 38 - 7 R48685 1 Dowel Pin -
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE515513PCDD01
P1064-3 06/15
1 - 8
GROUP 1 – ENGINE
Crankshaft Pulley
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R517208 1 Pulley, 173 mm O.D. - 2 R517237 1 Washer - 3 R516648 1 Capscrew, M20 x 2.5 x 70 mm (Do not re-use) - R520451 1 Adhesive (Loctite #620 - not shown) -
NL1064T23
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE516806PCDA01
P1064-3 06/15
1 - 9
GROUP 1 – ENGINE
Crankshaft Pulley
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R505567 1 Pulley, 173 mm O.D. - 2 R515040 1 Bushing - 3 R516648 1 Capscrew, M20 x 2.5 x 70 mm (Do not re-use) -
NL1064H33 & NL1064H43
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE515238PCDD02
P1064-3 06/15
1 - 10
GROUP 1 – ENGINE
Cylinder Liner and Connecting Rod
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE536156 4 Piston Liner Kit (includes keys #2-5) - 2 1 Cylinder Liner* - 3 AR65507 1 O-ring Kit - 4 RE507852 1 Piston Ring Kit - 5 1 Piston (marked RE532136)* - 6 R123178 4 Piston Pin - 7 M41029 8 Snap Ring - 8 RE500002 4 Connecting Rod (marked R500000, includes keys 9 & 10) - 9 R123960 1 Bushing - 10 R501124 2 Screw, M12 x 61 mm - 11 RE65908 4 Bearing Kit, Standard - RE65909 4 Bearing Kit, 0.254 mm Undersize -
*Not available separately
NL1064T23
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE532143PCDA01
P1064-3 06/15
1 - 11
GROUP 1 – ENGINE
Cylinder Liner and Connecting Rod
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE527843 4 Piston Liner Kit (includes keys #2-5) - 2 1 Cylinder Liner* - 3 AR65507 1 O-ring Kit - 4 RE527844 1 Piston Ring Kit - 5 1 Piston (marked RE527039)* - 6 R502755 4 Piston Pin - 7 R54114 8 Snap Ring - 8 RE500608 4 Connecting Rod (marked R500335, includes keys 9 & 10) - 9 R114082 1 Bushing - 10 R501124 2 Screw, M12 x 61 mm - 11 RE65908 4 Bearing Kit, Standard - RE65909 4 Bearing Kit, 0.254 mm Undersize -
*Not available separately
NL1064H33
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE525600PCDB01
P1064-3 06/15
1 - 12
GROUP 1 – ENGINE
Cylinder Liner and Connecting Rod
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE524450 4 Piston Liner Kit (includes keys 2-5) - 2 1 Cylinder Liner* - 3 AR65507 1 O-ring Kit - 4 RE524453 1 Piston Ring Kit - 5 1 Piston (marked RE521616)* - 6 R502755 4 Piston Pin - 7 R54114 8 Snap Ring - 8 RE500608 4 Connecting Rod (marked R500335, includes keys 9-10) - 9 R114082 1 Bushing - 10 R501124 2 Screw, M12 x 61 mm - 11 RE65908 4 Bearing Kit, Standard - RE65909 4 Bearing Kit, 0.254 mm Undersize - *Not available separately
NL1064H43
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE523425PCDB01
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R134527 1 Front Plate - 2 R116386 3 Stud, M10 x 37 mm - 3 R134518 2 Stud, 68 mm - 4 R136475 4 Screw - 5 R123174 1 Thrust Washer - 6 R120641 1 Shaft - 7 RE508932 1 Gear (marked R505121, 49 Teeth) - 8 34H288 1 Spring Pin - 9 R131206 1 Thrust Washer - 10 19M8997 1 Capscrew, M10 x 65 mm - 11 R114194 1 Spacer - 12 R101225 1 Thrust Washer - 13 R123584 4 Stud, 79 mm - 14 DD15664 1 Sealant (not shown) -
GROUP 1 – ENGINE
Timing Gear Front Plate
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE509404PCDD01
NL1064T23
1 - 13
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R504576 1 Front Plate - 2 R520139 7 Stud, 84 mm - 3 R134518 2 Stud, 68 mm - 4 R136475 5 Screw, M8 x 20 - 5 R515408 1 Dowel Pin, 38.5 mm long - 6 R515494 2 Lock Washer - 7 R504843 1 Shaft - 8 RE508489 1 Gear (60 Teeth, marked R504614) - 9 19M8844 1 Screw, M10 x 60 - 10 R101225 1 Thrust Washer - 11 R114194 1 Shaft - 12 RE56369 1 Gear (43 Teeth, marked R120636) - 13 R114193 1 Bushing - 14 R131283 1 Thrust Washer - 15 19M8966 1 Screw, M10 x 50 -
GROUP 1 – ENGINE
Timing Gear Front Plate
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE505834PCDD02
NL1064H23, NL1064H33, & NL1064H43
1 - 14
P1064-3 06/15
GROUP 1 – ENGINE
1 - 15
RE531746PCDA01Reproduced by permission of Deere & Co., c2009 Deere & Company. All rights reserved.
Camshaft
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE531748 1 Camshaft NL1064T23 (marked R524506) - RE532238 1 Camshaft NL1064H23, NL1064H33 (marked R522621) - RE537237 1 Camshaft NL1064H43 (marked R518734) - 2 R132518 1 Plate - 3 19M8999 2 Capscrew, M8 x 25 mm -
P1064-3 06/15
1 - 16
GROUP 1 – ENGINE
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE502449 1 Balancer Shaft Assembly, Right hand (marked RE500448 - includes keys 3, 5-10) - 2 RE502448 1 Balancer Shaft Assembly, Left hand (marked RE500449 - includes keys 4-10) - 3 R120637 1 Gear (Right hand Shaft, 15 Teeth) - 4 R120639 1 Gear (Left hand Shaft, 15 Teeth) - 5 19M7864 1 Capscrew, M8 x 12 - 6 R116078 1 Plate - 7 R133303 1 Shaft Key - 8 19M7798 4 Capscrew, M8 x 40 - 9 R500265 2 Weight - 10 R115299 3 Bushing -
Engine Balancer Shaft
RE501265PCDD01Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064T23
Updated 2/18/10
P1064-3 06/15
1 - 17
GROUP 1 – ENGINE
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE502447 1 Balancer Shaft Assembly, Right hand (marked RE500448 - includes keys 3, 5-10) - 2 RE502446 1 Balancer Shaft Assembly, Left hand (marked RE500449 - includes keys 4-10) - 3 R120637 1 Gear (Right hand Shaft, 15 Teeth) - 4 R120639 1 Gear (Left hand Shaft, 15 Teeth) - 5 19M7864 1 Screw, M8 x 12 - 6 R116078 1 Plate - 7 R133303 1 Shaft Key - 8 19M7798 4 Capscrew, M8 x 40 - 9 R500650 2 Weight - 10 R115299 3 Bushing -
Engine Balancer Shaft
RE501264PCDD01Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064H23, NL1064H33, & NL1064H43
Updated 2/18/10
P1064-3 06/15
1 - 18
GROUP 1 – ENGINE
Timing Gear Cover, Coolant Pump, Idler Gear Assembly
RE509418PCDD01Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064T23
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE532938 1 Timing Gear Cover, Water Pump, Idler Gear Assembly - (includes keys 2-9, 16-26, 31) - 2 R520132 1 Gasket - 3 RE517370 2 Fitting - 4 51M7044 1 O-ring - 5 1 Cover (marked R520130, order RE532938) - 6 R121424 1 O-ring - 7 R121411 1 Cover - 8 19M7775 3 Capscrew, M6 x 16 - 9 RE516340 1 Seal - 10 19M8291 1 Capscrew, M8 x 35 - 11 RE67239 1 Capscrew, M8 x 45 - 12 19M7801 1 Capscrew, M8 x 60 - 13 19M8317 6 Capscrew, M8 x 40 - 14 14M7296 6 Flange Nut, M10 - 15 19M7979 2 Capscrew, M8 x 55 - 16 19M7796 8 Capscrew, M6 x 30 - 17 51M7040 1 O-ring - 18 RE46685 1 Plug, M18 x 1.5 - 19 RE505981 1 Coolant Pump (includes keys 17-24, also order Gasket key 25 & Tube Seal key 21) - 20 RE515314 1 Impeller & Shaft Kit (includes keys 21-24, also order Gasket key 25 & Tube Seal key 21) - 21 R123226 1 Tube Seal - 22 R71228 1 Ring - 23 A364R 1 Snap Ring - 24 1 Impeller (marked R121036, order RE515314)* - 25 R123417 1 Gasket - 26 RE508566 1 Insert Kit - 27 19M8966 1 Capscrew, M10 x 50 - 28 R131283 1 Thrust Washer - 29 R114193 1 Bushing - 30 RE56369 1 Gear, 43 Teeth (marked R120636) - 31 19M7867 1 Capscrew, M8 x 25 -
*Not available separately
GROUP 1 – ENGINE
1 - 19
NL1064T23
Timing Gear Cover, Coolant Pump, Idler Gear Assembly
P1064-3 06/15
1 - 20
GROUP 1 – ENGINE
RE516919PCDE01Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064H23 & NL1064H33
Timing Gear Cover, Coolant Pump, Idler Gear Assembly
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE505840 1 Timing Gear Cover, Water Pump, Idler Gear Assembly (includes keys 2, 11-26) - 2 1 Timing Gear Cover (marked R503769, order RE505840)* - 3 19M7800 5 Capscrew, M8 x 50 - 4 RE46687 1 Plug, M22 x 1.5 - 5 51M7045 1 O-ring - 6 14M7296 9 Flange Nut, M10 - 7 RE517370 1 Fitting, M20 x 1.5 - 8 51M7044 1 O-ring - 9 RE516340 1 Seal - 10 19M7801 3 Capscrew, M8 x 60 - 11 19M7863 5 Capscrew, M6 x 25 - 12 19M7796 3 Capscrew, M6 x 30 - 13 RE46685 1 Plug, M18 x 1.5 - 14 51M7043 1 O-ring - 15 RE505980 1 Coolant Pump (includes keys 13-23, also order Gaskets key 24 and - Tube Seal key 23) - 16 RE509813 1 Impeller & Shaft Kit (includes keys 16-22, also order Gasket key 24 and - Tube Seal key 23) - 17 R71228 1 Ring - 18 A364R 1 Snap Ring - 19 1 Shaft - 20 1 Ball Bearing - 21 1 Seal - 22 1 Impeller (marked R123395) - 23 R123226 1 Tube Seal - 24 R123417 1 Gasket - 25 RE508566 1 Insert Kit - 26 R504734 1 O-ring - 27 19M7867 1 Capscrew, M8 x 25 - 28 R523185 1 Gasket - 29 R516557 1 Adapter - 30 19M7805 4 Capscrew, M10 x 45 -
*Not available separately
GROUP 1 – ENGINE
1 - 21
NL 1064H23 & NL1064H33
Timing Gear Cover, Coolant Pump, Idler Gear Assembly
} order RE509813
P1064-3 06/15
1 - 22
GROUP 1 – ENGINE
RE523283PCDB01Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064H43
Timing Gear Cover, Coolant Pump, Idler Gear Assembly
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE526615 1 Timing Gear Cover, Water Pump, Idler Gear Assembly (includes keys 2-18) - 2 1 Timing Gear Cover (marked R503769, order RE526615)* - 3 R504734 1 O-ring - 4 19M7863 5 Capscrew, M6 x 25 - 5 19M7796 3 Capscrew, M6 x 30 - 6 RE523169 1 Coolant Pump (includes keys 7-16, also order Tube Seal key 31) - 7 RE509813 1 Impeller & Shaft Kit (includes keys 11-16, also order Gasket key 17 and Tube Seal key 31) 8 R98527 2 Filter - 9 51M7043 1 O-ring - 10 RE46685 1 Plug, M18 x 1.5 - 11 R71228 1 Snap Ring - 12 A364R 1 Snap Ring - 13 1 Shaft - 14 1 Ball Bearing - 15 1 Seal - 16 1 Impeller (marked R123395) - 17 R123417 1 Gasket - 18 RE508566 1 Insert Assembly - 19 R516557 1 Adapter - 20 19M7805 4 Capscrew, M10 x 45 - 21 51M7045 1 O-ring - 22 RE46687 1 Plug, M22 x 1.5 - 23 19M7800 5 Capscrew, M8 x 50 - 24 14M7296 9 Flange Nut, M10 - 25 51M7044 1 O-ring - 26 RE517370 ** Plug, M20 x 1.5 - 27 RE516340 1 Seal - 28 19M7801 3 Capscrew, M8 x 60 - 29 R523185 1 Gasket - 30 19M7867 1 Capscrew, M8 x 25 - 31 R123226 2 Tube Seal - *Not available separately **As required
GROUP 1 – ENGINE
1 - 23
NL1064H43
Timing Gear Cover, Coolant Pump, Idler Gear Assembly
}order RE509813
P1064-3 06/15
1 - 24
GROUP 1 - ENGINE
Oil Filter and Adapter
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE508700PCDD01
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE508986 1 Filter Head Assembly (includes keys 2-8) - 2 R501484 1 Gasket - 3 RE52242 2 Drain Plug (includes key 4) - 4 51M7042 2 O-ring - 5 RE504562 1 Filter Head with Valve (includes key 6, and can order RE508986) - 6 R502513 1 Seal - 7 RE67238 1 Screw, M8 x 20 (with pre-applied sealant) - 8 19M7802 5 Screw, M8 x 65 - 9 RE504836 1 Oil Filter -
P1064-3 06/15
1 - 25
GROUP 1 - ENGINE
Oil Pump
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE57763PCDD01
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE504914 1 Oil Pump (includes key 2) - 2 R97185 1 O-ring - 3 R120638 1 Gear, 30 Teeth - 4 14M7066 1 Nut - 5 19M8987 2 Screw, M8 x 65 - 6 R121376 1 Tube -
P1064-3 06/15
1 - 26
GROUP 1 - ENGINE
Oil Pan
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE520892PCDB01
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE520147 1 Oil Pan - 2 R521493 1 Gasket - 3 19M8062 6 Screw, M8 x 20 - 4 RE46685 3 Plug, M18 x 1.5 - 5 51M7043 1 O-ring - 6 15H690 1 Pipe Plug 3/4” - 7 RE46687 2 Plug, M22 x 1.5 - 8 51M7045 1 O-ring - 9 19M7902 22 Screw, M8 x 16 - 10 19M8986 2 Screw, M8 x 100 - 11 RE57619 1 Oil Pump Pick-up - 12 R61871 1 O-ring -
NL1064T23, NL1064H23, and NL1064H33
P1064-3 06/15
1 - 27
GROUP 1 - ENGINE
Oil Pan
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE506951PCDE01
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE503784 1 Oil Pan - 2 R123353 1 Gasket - 3 19M7868 6 Screw, M8 x 30 - 4 19M7867 18 Screw, M8 x 25 - 5 RE46685 2 Plug, M18 x 1.5 - 6 51M7043 1 O-ring - 7 19M7799 4 Screw, M8 x 45 - 8 RE46687 2 Plug, M22 x 1.5 - 9 51M7045 1 O-ring - 10 19M8986 2 Screw, M8 x 100 - 11 RE68491 1 Oil Pump Intake - 12 R61871 1 O-ring -
NL1064H43
P1064-3 06/15
1 - 28
GROUP 1 - ENGINE
Dipstick & Tube, Right Hand
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE58181PCDD01
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE69243 1 Dipstick - 2 R502604 1 Dipstick Tube - 3 R502725 1 Plug -
P1064-3 06/15
GROUP 1 - ENGINE
1 - 29
Notes
P1064-3 06/15
1 - 30
GROUP 1 - ENGINE
Cylinder Head
RE531087PCDA01Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064T23
P1064-3 06/15
1 - 31
GROUP 1 - ENGINE
Cylinder Head
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE531088 1 Cylinder Head (marked R523078, includes keys 2-14) - 2 RE31617 8 Seal - 3 R106831 4 Valve Seat Insert, Intake - 4 R98062 4 Intake Valve, Standard - R97490 4 Intake Valve, .015" Oversize - R97491 4 Intake Valve, .030" Oversize - 5 R106829 4 Valve Seat Insert, Exhaust - 6 R90692 4 Exhaust Valve, Standard - R97492 4 Exhaust Valve, .015" Oversize - R97493 4 Exhaust Valve, .030" Oversize - 7 R43409 2 Plug - 8 21-09507 1 Plug, Socket Head 5/8 O-ring Port (includes key 9) - 9 R26906 1 O-ring - 10 CD16284 1 Plug, Rear - 11 RE42713 ** Plug 1/8 NPT - 12 R91889 16 Retainer - 13 RE60005 8 Rotator - 14 R26125 8 Spring - 15 R85363 18 Capscrew, Hex Head Flanged 1/2-13 x 4.41” (marked E112) - 16 R116515 1 Head Gasket -
**As required
NL1064T23
P1064-3 06/15
1 - 32
GROUP 1 - ENGINE
Cylinder Head
RE525460PCDA01Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064H23 & NL1064H33
P1064-3 06/15
1 - 33
GROUP 1 - ENGINE
Cylinder Head
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE525458 1 Cylinder Head (marked R520778, includes keys 2-15) - 2 RE529811 8 Seal - 3 R106831 4 Valve Seat Insert, Intake - 4 R98062 4 Intake Valve, Standard - R97490 4 Intake Valve, .015" Oversize - R97491 4 Intake Valve, .030" Oversize - 5 R106829 4 Valve Seat Insert, Exhaust - 6 R90692 4 Exhaust Valve, Standard - R97492 4 Exhaust Valve, .015" Oversize - R97493 4 Exhaust Valve, .030" Oversize - 7 R43409 3 Plug - 8 21-09507 1 Plug, Socket Head 5/8 O-ring Port (includes key 9) - 9 R26906 1 O-ring - 10 CD16284 1 Plug - 11 RE42713 ** Plug 1/8 NPT - 12 RE527456 4 Sleeve Assembly - 13 R91889 16 Retainer - 14 RE60005 8 Rotator - 15 R26125 8 Spring - 16 R502511 2 Capscrew, Hex Head Flanged 1/2-13 x 5.43” (marked E138) - 17 R85363 16 Capscrew, Hex Head Flanged 1/2-13 x 4.41” (marked E112) - 18 R116515 1 Head Gasket - **As required
NL1064H23 & NL1064H33
P1064-3 06/15
1 - 34
GROUP 1 - ENGINE
Cylinder Head
RE523445PCDA02Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064H43
P1064-3 06/15
1 - 35
GROUP 1 - ENGINE
Cylinder Head
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE523430 1 Cylinder Head (marked R520109, includes keys 2-13) - 2 CD16284 3 Plug - 3 R520867 5 O-ring - 4 RE531221 4 Intake Valve (kit 2 ea., R518806 ea.) - 5 RE518081 4 Exhaust Valve (kit 2 ea., R502370 ea.) - 6 RE518082 8 Valve Seat Insert, Intake - 7 RE518083 8 Valve Seat Insert, Exhaust - 8 RE517435 4 Sleeve Assembly - 9 RE526519 16 Seal - 10 R518872 16 Spring - 11 R502367 16 Cap - 12 R502371 32 Retainer - 13 RE42713 1 Plug, 1/8 NPT - 14 R519582 4 Sleeve - 15 R521544 2 Bushing - 16 R502511 18 Capscrew, Hex Head Flanged 1/2-13 x 5.43” (marked E138) - 17 R116515 1 Head Gasket -
NL1064H43
P1064-3 06/15
1 - 36
GROUP 1 - ENGINE
Rocker Shaft Assembly & Push Rods
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE519736 1 Rocker Shaft Assembly (includes keys 6-12) - 2 R123271 4 Stud - 3 24M7346 4 Washer - 4 R123565 8 Cam Follower - 5 R107731 8 Push Rod - 6 R54565 2 Plug - 7 T20316 2 Washer - 8 RE508317 8 Rocker Arm - 9 14M7148 1 Hex Nut, M10 - 10 R123161 4 Support - 11 T20314 3 Spring - 12 R123513 1 Rocker Shaft - 13 R133630 8 Adjusting Stud -
RE57618PCDA01Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064T23, NL1064H23, & NL1064H33
P1064-3 06/15
1 - 37
GROUP 1 - ENGINE
Rocker Shaft Assembly & Push Rods
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE533149 1 Rocker Arm Assembly (includes keys 2-13) - 2 1 Housing (not available separately, marked R522426 or R525453) - 3 RE516490 1 Rocker Arm Shaft (marked R505150) - 4 30M7004 2 Plug - 5 RE523023 4 Rocker Arm, Intake (includes key 7) - 6 RE504210 4 Rocker Arm, Exhaust (includes key 7) - 7 14M7148 8 Hex Nut, M10 - 8 R505543 4 Spring - 9 R504631 1 Clamp - 10 RE523032 1 Cap - 11 19M8966 1 Screw - 12 19M9170 1 Screw, M8 x 50 - 13 R520867 1 O-ring - 14 R123565 8 Cam Follower - 15 R504209 8 Push Rod - 16 R505174 1 Gasket - 17 R516140 3 Strap - 18 24M7096 2 Washer - 19 R521458 5 Screw - 20 R502341 8 Valve -
RE523427PCDC01Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064H43
P1064-3 06/15
1 - 38
GROUP 1 - ENGINE
Rocker Arm Cover
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE70401 1 Rocker Arm Cover, Front Oil Fill (marked R519777) - 2 R524480 1 Gasket - 3 H123575 4 O-ring - 4 00-09508 1 Label “Northern Lights” - 5 RE500005 1 Filler Cap (includes key #6) - 6 R502902 1 Packing - 7 H23125 4 Plug - 8 R123574 4 Hex Nut, M8 -
NL1064T23
RE57606PCDG01Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
P1064-3 06/15
1 - 39
GROUP 1 - ENGINE
Rocker Arm Cover
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R521326 1 Rocker Arm Cover - 2 RE528742 1 Defl ector - 3 19M7862 1 Capscrew, M6 x 20 - 4 R5244568 1 Gasket - 5 R123575 4 O-ring - 6 R123574 1 Hex Nut M8 - 7 H23125 4 Plug - 8 R522409 1 Heat Shield - 9 RE527858 2 Capscrew, M6 x 12 (threads with pre-applied sealant) - 10 RE500005 1 Filler Cap - 11 R502902 1 Packing - 12 00-09508 1 Label “Northern Lights” -
RE530011PCDA01Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064H23 & NL1064H33
P1064-3 06/15
1 - 40
GROUP 1 - ENGINE
Rocker Arm Cover
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R522165 1 Rocker Arm Cover - 2 R515555 1 Defl ector - 3 19M7775 2 Capscrew, M6 x 16 - 4 R505174 1 Gasket - 5 R123575 5 O-ring - 6 H521390 5 Capscrew, M8 x 12 - 7 H23125 5 Plug - 8 00-09508 1 Label “Northern Lights” - 9 RE500005 1 Filler Cap (includes key 10) - 10 R502902 1 Packing -
NL1064H43
RE526685PCDA01Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R72328 1 O-ring - 2 R120467 1 Elbow Fitting 900 - 3 R72659 1 Clamp - 4 19M7865 1 Capscrew, M8 x 16 - 5 41-00004 ** Hose, 3/4" I.D. (sold per inch) -
**As required
1 - 41
GROUP 1 - ENGINE
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE69291PCDE01
NL1064T23
Ventilating System
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R120467 1 Elbow Fitting 900 - 2 R72328 1 O-ring - 3 41-00004 ** Hose, 3/4" I.D. (sold per inch) -
**As required
1 - 42
GROUP 1 - ENGINE
Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved. RE532164PCDA01
NL1064H23, NL1064H33, & NL1064H43
Ventilating System
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE533438 1 Air Intake - 2 AR65294 2 Clamp - 3 R500596 1 Hose - 4 19M8528 2 Capscrew, M10 x 55 - 5 RE60071 2 Plug, M10 x 1.0 (includes key 6) - 6 51M7039 1 O-ring - 7 R81275 2 Gasket - 8 R501472 1 Spacer -
2 - 1
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE532573PCDA01
NL1064T23
Air IntakeGROUP 2 - INTAKE AND EXHAUST SYSTEMS
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE508742 1 Intake Manifold - 2 19M8292 2 Capscrew, M10 x 50 - 3 R81275 2 Gasket - 4 R501472 1 Spacer - 5 RE60071 2 Plug, M10 x 1.0 (includes key 6) - 6 51M7039 1 O-ring - 7 RE46684 1 Plug, M14 x 1.5 (includes key 8) - 8 51M7041 1 O-ring -
2 - 2
Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved. RE509839PCDE01
NL1064H23 & NL1064H33
Air IntakeGROUP 2 - INTAKE AND EXHAUST SYSTEMS
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE519456 1 Intake Manifold - 2 R519532 1 Gasket - 3 19M7785 7 Capscrew, M10 x 25 - 4 19M7811 4 Capscrew, M10 x 90 - 5 RE528692 1 Air Intake - 6 R521061 1 Gasket - 7 R522521 1 Sleeve -
2 - 3
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE522828PCDA01
NL1064H43
Air IntakeGROUP 2 - INTAKE AND EXHAUST SYSTEMS
P1064-3 06/15
GROUP 2 - INTAKE AND EXHAUST SYSTEMS
Air Filter Assembly
2 - 4
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
•• AT203471 1 Air Filter Assembly (includes keys #1-5) - 1 RE501727 1 Cover - 2 R122386 1 Clip - 3 AT203469 1 Outer Element - 4 AT203470 1 Inner Element - 5 T158495 1 Valve - 6 AT175358 1 Rain Cap (Standard) - 24-21408 1 Air Pre-cleaner (optional) - 7 AR35435 2 Mounting Bracket - 8 19M7784 4 Capscrew, M10 x 1.5 x 20 mm - 9 14-80811 4 Flange Nut, M10 x 1.5 - 10 R128438 1 Hose - 11 AT56657 1 Hose Clamp - 12 AT50923 1 Hose Clamp -
Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved. RGP6292
NL1064T23
P1064-3 06/15
2 - 5
Notes GROUP 2 - INTAKE AND EXHAUST SYSTEMS
P1064-3 06/15
GROUP 2 - INTAKE AND EXHAUST SYSTEMS
Air Filter Assembly
2 - 6
Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved. RGP6292changed
NL1064H23 & NL1064H33
Updated 2/18/10
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 AT203471 1 Air Filter Assembly - 2 AT175358 1 Rain Hood - 3 AR35435 2 Clamp/ Bracket - 4 23-29406 1 Bracket, Air Filter Mtg. - 5 18-29401 1 Elbow 4" I.D. 900 - 6 18-25701 1 Hump Hose 4" x 3" x 5" - 7 R517439 1 Tube 4" O.D. - 8 19-01450 3 T-Bolt Clamp 4-1/2" S/S - 9 19-01350 1 T-Bolt Clamp 3-1/2" S/S - 10 12-00805 4 Capscrew, Hex Head M10 x 1.5 x 20 mm - 11 15-00805 8 Flat Washer M10 - 12 15-00802 4 Lock Washer, Helical M10 - 13 14-00812 4 Hex Nut, Nylock M10 x 1.5 - 14 12-00835 1 Capscrew, Hex Head M10 x 1.25 x 25 mm - 15 15-00301 1 Flat Washer 3/8" - 16 12-00912 4 Capscrew, Hex Head M12 x 1.75 x 25 mm - 17 15-00912 4 Lock Washer, Helical M12 - 18 RE501727 1 Cover - 19 R122386 1 Clip - 20 AT203469 1 Outer Element - 21 AT203470 1 Inner Element - 22 T158495 1 Valve -
GROUP 2 - INTAKE AND EXHAUST SYSTEMS
NL1064H23 & NL1064H33
Air Filter Assembly
2 - 7
Updated 2/18/10
P1064-3 06/15
GROUP 2 - INTAKE AND EXHAUST SYSTEMS
Air Filter Assembly
2 - 8
Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved. A-11793/ RGP6292&RE528391PCDA01
NL1064H43
Updated 2/18/10
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 AT203471 1 Air Filter Assembly - 2 AT175358 1 Rain Hood - 3 AR35435 2 Clamp/ Bracket - 4 23-29407 1 Bracket, Air Filter Mtg. - 5 18-29402 1 Elbow 4" I.D. x 5” I.D. - 6 RE525454 1 Hump Hose 4" x 5" with Sensor Port - 7 27-29408 1 Tube 5" O.D. x 2-1/2” - 8 RE67746 1 Hose Clamp - 9 19-01550 2 T-Bolt Clamp 5-1/2" S/S - 10 12-00805 4 Capscrew, Hex Head M10 x 1.5 x 20 mm - 11 15-00805 8 Flat Washer M10 - 12 15-00802 4 Lock Washer, Helical M10 - 13 14-00812 4 Hex Nut, Nylock M10 x 1.5 - 14 12-00713 1 Capscrew, Hex Head M8 x 1.25 x 5 mm - 15 15-00702 1 Lock Washer M8 - 16 12-04802 4 Capscrew, Hex Head M12 x 1.75 x 40 mm - 17 15-00912 4 Lock Washer, Helical M12 - 18 RE501727 1 Cover - 19 R122386 1 Clip - 20 AT203469 1 Outer Element - 21 AT203470 1 Inner Element - 22 T158495 1 Valve - 23 RE528301 1 Wiring Harness (Includes 24 -25) - 24 AZ100110 1 Electrical Connector Assembly (also order 2 ea. of Terminal 57M8164 - & Electrical Connection Locking Device 57M7621) - 25 57M8601 1 Electrical Connector Housing (also order 2 ea. of Terminal 57M8560, - Electrical Connection Locking Device 57M8633, & Electrical - Connector Seal 57M8566) -
GROUP 2 - INTAKE AND EXHAUST SYSTEMS
NL1064H43
Air Filter Assembly
2 - 9
Updated 2/18/10
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE532282 1 Turbocharger - 2 R92097 1 Gasket - 3 19M8162 4 Capscrew, M10 x 40 - 4 14M7296 4 Flange Nut, M10 - 5 M87733 1 Fitting (also order key #3 o-ring) - 6 R63548 1 O-ring - 7 R123570 1 Gasket - 8 19M8062 2 Capscrew, M8 x 20 - 9 RE59547 1 Oil Line - 10 RE65978 2 Clamp - 11 R523372 1 Hose - 12 RE54885 1 Male Connector, 1/2 NPT x HB (with pre-applied sealant) - 13 RE501260 1 Hose Assembly - 14 38H5154 1 Elbow Fitting, M16 (also order keys 15 &16 o-rings) - 15 T77613 1 O-ring - 16 51M7042 1 O-ring -
2 - 10
Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved. RE531936PCDA01
NL1064T23
Turbocharger and Oil LinesGROUP 2 - INTAKE AND EXHAUST SYSTEMS
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE531074 1 Turbocharger - 2 R123572 1 Gasket - 3 R522679 4 Capscrew, M10 x 25 - 4 M87733 1 Fitting (also order key #3) - 5 R63548 1 O-ring - 6 R123570 1 Gasket - 7 19M7866 2 Capscrew, M8 x 20 - 8 RE530682 1 Oil Line - 9 RE65978 2 Clamp - 10 R523372 1 Hose - 11 RE54885 1 Male Connector, 1/2 NPT x HB (with pre-applied sealant) - 12 51M7042 1 O-ring - 13 RE531244 1 Hose Assembly - 14 T77613 1 O-ring - 15 38H5154 1 Elbow Fitting, M16 (also order key #14 o-ring) -
2 - 11
Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.RE530510PCDB01
NL1064H23 & NL1064H33
Turbocharger and Oil LinesGROUP 2 - INTAKE AND EXHAUST SYSTEMS
P1064-3 06/15
2 - 12
Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.RE523389PCDB01
NL1064H43
Turbocharger and Oil LinesGROUP 2 - INTAKE AND EXHAUST SYSTEMS
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE535239 1 Turbocharger/ Actuator Assembly 12V (formerly RE526469 & - RE530117) - RE535241 1 Turbocharger/ Actuator Assembly 24V (formerly RE530118 & - RE527571) - 2 RE529234 1 Actuator 12V (used with RE526469 & RE530117) - RE529237 1 Actuator 24V (used with RE530118 & RE527571) - RE535331 1 Actuator 24V (used with RE535241) - RE535333 1 Actuator 12V (used with RE535239) - 3 RE524231 1 Fitting - 4 R63548 1 O-ring - 5 RE529235 1 Sensor - 6 R519484 2 Capscrew, M10 x 45 - 7 R520632 1 Spacer - 8 T38545 1 Clamp - 9 19M7811 1 Capscrew, M10 x 90 - 10 RE526554 1 Oil Line - 11 RE521531 1 Fitting - 12 R519489 1 Gasket - 13 14M7296 4 Flange Nut M10 - 14 R521200 2 Stud, 49 mm - 15 R521158 1 Gasket - 16 N275830 2 Capscrew, M8 x 25 - 17 RE523311 1 Oil Line - 18 RE65978 2 Clamp - 19 R120013 1 Hose, 915 mm - 20 RE54885 1 Hose Fitting - 21 38H5022 3 Elbow Fitting (also order key #23 o-ring) - 22 51M7040 1 O-ring - 23 T77613 1 O-ring - 24 AH80916 1 Clip - 25 19M7774 1 Capscrew, M6 x 12 - 26 RE523376 1 Line - 27 38H5008 1 Adapter Fitting (also order key #23 o-ring) - 28 RE526555 1 Oil Line - 29 R520856 1 Clamp - 30 RE527858 1 Screw - 31 R524452 1 Clamp - 32 R524453 1 Clamp -
2 - 13
GROUP 2 - INTAKE AND EXHAUST SYSTEMS
Turbocharger and Oil Lines
NL1064H43
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R132261 1 Exhaust Manifold - 2 R521439 4 Gasket - 3 19M7810 8 Capscrew, M10 x 80 -
2 - 14
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE57864PCDD01
NL1064T23
Exhaust ManifoldGROUP 2 - INTAKE AND EXHAUST SYSTEMS
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R524029 1 Exhaust Manifold - 2 R521439 4 Gasket - 3 R522554 8 Capscrew, M10 x 80 -
2 - 15
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE529090PCDB02
NL106423 & NL1064H33
Exhaust ManifoldGROUP 2 - INTAKE AND EXHAUST SYSTEMS
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R522090 1 Exhaust Manifold - 3 R519486 8 Capscrew, M10 x 125 - 2 R519488 4 Gasket - 4 RE42713 1 Plug, 1/8 NPT -
2 - 16
Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved. RE522757PCDB01
NL1064H43
Exhaust ManifoldGROUP 2 - INTAKE AND EXHAUST SYSTEMS
P1064-3 06/15
GROUP 2 - INTAKE AND EXHAUST SYSTEMS
Dry Exhaust Elbow
Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.RGP6262
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 R123246 1 Exhaust Elbow - 2 R87732 1 Adapter - 3 RE40048 1 Clamp - 4 19M8162 4 Screw, M10 x 40 - 5 14M7296 4 Flange Nut, M10 -
NL1064T23
2 - 17
P1064-3 06/15
GROUP 2 - INTAKE AND EXHAUST SYSTEMS
Dry Exhaust Elbow
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE531152PCDA01
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 R524317 1 Exhaust Elbow - 2 R87732 1 Adapter - 3 RE40048 1 Clamp - 4 R521200 2 Stud - 5 19M8162 2 Capscrew, M10 x 40 - 6 14M7296 4 Flange Nut -
NL1064H23 & NL1064H33
2 - 18
P1064-3 06/15
GROUP 2 - INTAKE AND EXHAUST SYSTEMS
Dry Exhaust Elbow
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE528498PCDA01
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 R522545 1 Exhaust Elbow - 2 R516794 1 Adapter - 3 RE40048 1 Clamp - 4 19M7786 4 Capscrew, M10 x 30 -
NL1064H43
2 - 19
P1064-3 06/15
2 - 20
GROUP 2 - INTAKE AND EXHAUST SYSTEMS
Exhaust Adapter 4"
A-1088E, A-6861A/ B-1566B
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 31-31066 1 Exhaust Adapter 4" - 27-31009 1 Exhaust Flex S/S 4" x 18" - 2 AR43704 2 Clamp kit with fasteners (includes keys 3-5) - 3 14-00311 2 Hex Nut 3/8- 16 - 4 15-00321 4 Flat Washer 3/8" SAE - 5 12-00310 2 Capscrew, Hex Head 3/8- 16 x 3" - 6 12-00914 8 Capscrew, Hex Head 5/8- 11 x 1- 3/4" - 7 15-00902 8 Lock Washer Helical 5/8" - 8 14-00911 8 Hex Nut 5/8- 11 - 9 11-31099 1 Gasket -
NL1064T23, NL1064H23, & NL1064H33
Updated 2/18/10
P1064-3 06/15
2 - 21
GROUP 2 - INTAKE AND EXHAUST SYSTEMS
Exhaust Adapter 5"
A-12226/ B-1566B
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 31-31013 1 Exhaust Adapter 5" - 27-32506 1 Exhaust Flex S/S 5" x 18" - 2 AR43704 2 Clamp kit with fasteners (includes keys 3-5) - 3 14-00311 2 Hex Nut 3/8- 16 - 4 15-00321 4 Flat Washer 3/8" SAE - 5 12-00310 2 Capscrew, Hex Head 3/8- 16 x 3" - 6 12-01216 8 Capscrew, Hex Head 3/4- 10 x 2" - 7 15-01202 8 Lock Washer Helical 3/4" - 8 14-01211 8 Hex Nut 3/4- 10 - 9 11-31096 1 Gasket -
NL1064H43
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R502983 1 Inlet Adapter - 2 R89944 1 O-ring - 3 19M7867 1 Capscrew, M8 x 25 - 4 19M7802 1 Capscrew, M8 x 65 - 5 RE46685 1 Fitting Plug, M18 x 1.5 - 6 51M7043 1 O-ring -
GROUP 3 - COOLING SYSTEM
Coolant Pump Inlet
3 - 0
RE507202PCDD01Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R121038 1 Pulley, 113 mm O.D. NL1064T23, NL1064H23, NL1064H33 - R115250 1 Pulley, 94 mm O.D. NL1064H43 - 2 19M7774 3 Capscrew, Hex Head Flanged M6 x 12 -
GROUP 3 - COOLING SYSTEM
Coolant Pump
3 - 1
RE57779PCDD02Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R501556 1 Thermostat Cover - 2 H502814 1 Gasket - 3 15H584 3 Plug - 4 RE46684 ** Plug, M14 x 1.5 (includes key 5) - 5 51M7041 ** O-ring - 6 19M7809 1 Capscrew, M10 x 70 - 7 19M7788 1 Capscrew, M12 x 25 - 8 R123323 1 Clamp - 9 19M7786 1 Capscrew, M10 x 30 - 10 R123226 1 Tube Seal - 11 R123629 1 Tube - 12 R123324 1 Clamp -
**As required
GROUP 3 - COOLING SYSTEM
Thermostat Cover
3 - 2
RE59868PCDD01Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064T23
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R131016 1 Thermostat Cover - 2 R502814 1 Gasket - 3 19M8292 1 Capscrew, M10 x 50 - 4 RE46684 ** Plug, M14 x 1.5 (includes key 5) - 5 51M7041 ** O-ring - 6 19M7786 1 Capscrew, M10 x 30 - 7 R123226 1 Gasket - 8 R521205 1 Tube - 9 R123324 1 Clamp -
**As required
GROUP 3 - COOLING SYSTEM
Thermostat Cover
3 - 3
RE525602PCDA01Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064H23 & NL1064H33
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE522076 1 Thermostat -
GROUP 3 - COOLING SYSTEM
Thermostat
3 - 4
RE59717PCDD01Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064T23, NL1064H23, & NL1064H33
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R519491 1 Thermostat Cover - 2 19M7786 3 Capscrew, M10 x 30 -
GROUP 3 - COOLING SYSTEM
Thermostat Cover
3 - 5
RE522740PCDB01Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064H43
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE527018 1 Thermostat - 2 R521548 3 Seal - 3 RE538289 2 Thermostat -
GROUP 3 - COOLING SYSTEM
Thermostat
3 - 6
RE522818PCDF01Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064H43
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE59296 1 Oil Cooler, 5 Plates (NL1064T23) - RE56690 1 Oil Cooler, 7 Plates (NL1064H23, NL1064H33) - 2 T122075 2 O-ring - 3 RE67231 6 Capscrew, M6 x 16 (with pre-applied sealant) - 4 R123501 1 Gasket - 5 R123471 1 Housing - 6 RE46686 1 Fitting Plug, M12 x 1.5 - 7 51M7040 1 O-ring - 8 RE508599 1 Housing Assembly (includes keys 9-10, & 13, marked R502811) - 9 R501428 1 Gasket - 10 R504734 1 O-ring - 11 19M7802 2 Capscrew, M8 x 65 - 12 19M7970 2 Capscrew, M8 x 100 - 13 RE67238 1 Capscrew, M8 x 20 (with pre-applied sealant) - 14 RE46685 1 Plug, M18 x 1.5 - 15 51M7043 1 O-ring -
GROUP 3 - COOLING SYSTEM
Engine Oil Cooler
3 - 7
RE59751PCDD01Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064T23, NL1064H23, & NL1064H33
Updated 2/18/10
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE56690 1 Oil Cooler, 7 Plates - 2 T122075 2 O-ring - 3 RE67231 6 Capscrew, M6 x 16 (with pre-applied sealant) - 4 R123501 1 Gasket - 5 R520983 1 Housing - 6 RE46686 1 Plug, M12 x 1.5 - 7 51M7040 1 O-ring - 8 RE508599 1 Housing Assembly (includes keys 9-11, & 14, marked R502811) - 9 R501428 1 Gasket - 10 R504734 1 O-ring - 11 19M7802 2 Capscrew, M8 x 65 - 12 19M7970 2 Capscrew, M8 x 100 - 13 RE67238 1 Capscrew, M8 x 20 (with pre-applied sealant) - 14 RE46685 1 Plug, M18 x 1.5 - 15 51M7043 1 O-ring -
GROUP 3 - COOLING SYSTEM
Engine Oil Cooler
3 - 8
RE526549PCDA01Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064H43
Updated 2/18/10
P1064-3 06/15
GROUP 3 - COOLING SYSTEM
Idler Shaft Assembly
NL1064T23, NL1064H23, & NL1064H33
RE59714PCDD01 & RE60114PCDD01Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE500538 1 Idler Shaft (includes keys #2-4) - 2 1 Ball Bearing* - 3 E1343FN 1 Snap Ring - 4 1 Hub* - 5 19M7835 4 Capscrew, Hex Head Flanged M10 x 1.5 x 35 mm - 6 R128660 1 Pulley, 173 mm O.D. - 7 19M7784 4 Capscrew, Hex Head Flanged M10 x 1.5 x 20 mm -
*No longer available separately - order complete Idler Shaft assembly.
3 - 9
P1064-3 06/15
GROUP 3 - COOLING SYSTEM
Idler Shaft Assembly
NL1064H43
RE59714PCDD01 & RE60114PCDD01Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE503664 1 Idler Shaft (includes keys #2-3) - 2 E1343FN 1 Snap Ring - 3 1 Hub* - 4 19M7786 4 Capscrew, Hex Head Flanged M10 x 30 mm - 5 R128660 1 Pulley, OD = 173 mm - 6 19M7784 4 Capscrew, M10 x 20 mm - *No longer available separately - order complete Idler Shaft assembly.
3 - 10
P1064-3 06/15
3 - 11
GROUP 3 - COOLING SYSTEM
Notes
P1064-3 06/15
A-12289/ B-9602
3 - 12
GROUP 3 - COOLING SYSTEM
Radiator
NL1064H23 & NL1064H33
Updated 2/18/10
P1064-3 06/15
GROUP 3 - COOLING SYSTEM
RadiatorNL1064H23 & NL1064H33
3 - 13
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 39-19416 1 Side Plate, Radiator Guard Right hand - 2 39-19414 1 Side Plate, Raidator Guard Left hand - 3 39-19413 1 Cross Member, Radiator Support - 4 39-19417 1 Top Panel, Radiator Guard - 5 39-19418 1 Lower Valance, Radiator Guard - 6 99000507 1 Radiator & Charge Air Cooler Sub Assembly (includes keys 17 & 22) - 7 81500019 1 Degas Tank Assembly - 8 RE533769 1 Fan 24” (Blower) - 9 R524645 1 Fan Spacer - 10 19M8896 4 Capscrew, Hex Head Flanged M10 x 1.5 x 140 mm - 11 21-70014 1 Female Adapter, Steel 3/8 NPT x M18 x 1.5 - 12 21-18301 1 Male Connector, Brass 3/8 NPT x 3/4 HB - 13 21-55003 1 Male Elbow, 900 Steel M12 x 1.5 x 1/4-37T - 14 21-71045 1 Female Swivel, Brass 1/4 HB x 1/4-45T Push-on - 15 41-01011 16” Hose, 1/4” ID Push-on - 16 23-19408 2 Bracket, Radiator Brace - 17 R524484 1 Charge Air Cooler, Aluminum - 18 19M9203 12 Capscrew, Hex Head Flanged M5 x 0.8 x 12mm - 19 19M7902 30 Capscrew, Hex Head Flanged M8 x 1.25 x 16 Serrated - 20 70500310 1 Bracket, Lifting Eye Right hand* - 21 70500312 1 Bracket, Lifting Eye Left hand* - 22 R524475 1 Radiator - 23 R523928 1 Bottom Bracket - 24 R524035 1 Fan Shroud - 25 R524036 1 Fan Guard - 26 R524493 1 Tube, Charge Air Cooler 2.5” OD - 27 R527653 1 Tube, Charge Air Cooler 2.5” OD - 28 R523202 1 Hose, Degas Vent, .37” ID - 29 R523556 1 Hose, Degas Tank Return, 3/4” ID - 30 R524044 1 Hose, 2” Diameter - 31 R524485 1 Hose, 1.73” ID - 32 R188811 2 Coupling, Charge Air Cooler, 2” x 2.5” ID Reducer - 33 R98495 2 Coupling, Charge Air Cooler, 2.5” x 3” ID Reducer - 34 19M7775 1 Capscrew, Hex Head Flanged M6 x 1 x 16 Serrated (not shown) - 35 TY22472 4 Clamp, 40-64 OD - 36 RE52702 2 Clamp, 70-92 OD - 37 RE518716 4 Clamp, 57-79 OD - 38 TY22464 2 Clamp, 11-20 OD - 39 TY22466 2 Clamp, 17-32 OD - 40 R519482 1 Clamp, 31-75 OD (not shown) - 41 RE56098 2 Clamp, 45-67 OD - 42 R524648 1 Bracket, Strap Mount Air Inlet - 43 R524649 1 Bracket, Strap Mount Turbo - 44 AW19033 2 Cable, Dual Eyelet, 9” - 45 R528257 2 Cable, Dual Eyelet, 5” - 46 14M7298 2 Hex Nut, Flanged M8 x 1.25 Serrated - 47 R505537 1 Capscrew, Hex Head Flanged M10 x 1.5 x 20 Serrated - 48 19M7867 1 Capscrew, Hex Head Flanged M8 x 1.25 x 25 Serrated -
*Not available separately
Updated 6/15/15
P1064-3 06/15
A-12288/ B-9602
3 - 14
GROUP 3 - COOLING SYSTEM
Radiator
NL1064H33
P1064-3 06/15
GROUP 3 - COOLING SYSTEM
Radiator
NL1064H33
3 - 15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 39-19416 1 Side Plate, Radiator Guard Right hand - 2 39-19414 1 Side Plate, Raidator Guard Left hand - 3 39-19413 1 Cross Member, Radiator Support - 4 39-19417 1 Top Panel, Radiator Guard - 5 39-19418 1 Lower Valance, Radiator Guard - 6 99000489 1 Radiator & Charge Air Cooler Sub Assembly (includes keys 17 & 22) - 7 81500019 1 Degas Tank Assembly - 8 RE533769 1 Fan 24” (Blower) - 9 R524645 1 Fan Spacer - 10 19M8896 4 Capscrew, Hex Head Flanged M10 x 1.5 x 140 mm - 11 21-70014 1 Female Adapter, Steel 3/8 NPT x M19 x 1.5 - 12 21-18301 1 Male Connector, Brass 3/8 NPT x 3/4 HB - 13 21-55003 1 Male Elbow, 900 Steel M12 x 1.5 x 1/4-37T - 14 21-71045 1 Female Swivel, Brass 1/4 HB x 1/4-45T Push-on - 15 41-01011 16” Hose, 1/4” ID Push-on - 16 23-19408 2 Bracket, Radiator Brace - 17 R523208 1 Charge Air Cooler, Aluminum - 18 19M9203 15 Capscrew, Hex Head Flanged M5 - .8 x 12 - 19 19M7902 24 Capscrew, Hex Head Flanged M8 - 1.25 x 16 Serrated - 20 70500310 1 Bracket, Lifting Eye Right hand* - 21 70500312 1 Bracket, Lifting Eye Left hand* - 22 R523207 1 Radiator - 23 R523928 1 Bottom Bracket - 24 R524035 1 Fan Shroud - 25 R524036 1 Fan Guard - 26 R524471 1 Tube, Charge Air Cooler 2.5” OD - 27 R524470 1 Tube, Charge Air Cooler 2.5” OD - 28 R523202 1 Hose, Degas Vent, .37” ID - 29 R523556 1 Hose, Degas Tank Return, 3/4” ID - 30 R524044 1 Hose, 2” Diameter - 31 R524473 1 Hose, 2.4” ID - 32 R188811 1 Coupling, Charge Air Cooler, 2” x 2.5” ID Reducer - 33 R98495 2 Coupling, Charge Air Cooler, 2.5” x 3” ID Reducer - 34 19M7775 1 Capscrew, Hex Head Flanged M6 - 1 x 16 Serrated (not shown) - 35 TY22472 2 Clamp, 40-64 OD - 36 RE52702 2 Clamp, 70-92 OD - 37 RE518716 5 Clamp, 57-79 OD - 38 TY22464 4 Clamp, 11-20 OD - 39 TY22466 2 Clamp, 17-32 OD - 40 TY22472 2 Clamp, 65-89 OD (not shown) - 41 R519482 1 Clamp, 1.25” OD - 42 R524648 1 Bracket, Strap Mount Air Inlet - 43 R524649 1 Bracket, Strap Mount Turbo - 44 AW19033 2 Cable, Dual Eyelet, 9” - 45 R524650 2 Cable, Dual Eyelet, 4” - 46 14M7298 2 Hex Nut, Flanged M8 - 1.25 Serrated - 47 R505537 1 Capscrew, Hex Head Flanged M10- 1.5 x 20 Serrated - 48 19M7867 1 Capscrew, Hex Head Flanged M8- 1.25 x 25 Serrated - 49 T181778 1 Coupling, Charge Air Cooler, 2.5” x 3.5” - 50 RE56098 1 Clamp, 45-67 OD -
*Not available separately
P1064-3 06/15
A-7615/ C-5778
3 - 16
GROUP 3 - COOLING SYSTEM
Radiator
NL1064T23
revised 4/8/10
P1064-3 06/15
GROUP 3 - COOLING SYSTEM
Radiator
NL1064T23
3 - 17
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 39-11015 2 Side Panel, Modular Radiator Guard - 2 39-11016 1 Top Panel, Modular Radiator Guard - 3 21-11001 2 Spacer Plate, Radiator Mtg. - 4 39-11017 1 Grille, Modular Radiator Guard - 5 RE64112 1 Radiator - 6 RE64114 1 Fan Shroud - 7 12-03310 4 Capscrew, Flh Skt 3/8- 16 x 3/4” - 8 12-00312 24 Capscrew, Hex Head 3/8- 16 x 1” - 9 15-00321 12 Lock Washer, Helical 3/8” - 10 12-00312 28 Flat Washer 3/8” - 11 15-00301 8 Flat Washer 3/8” - 12 14-00312 12 Hex Nut, Nylock 3/8- 16 - 13 14-00301 4 U-Nut 3/8- 16 - 14 12-00212 6 Capscrew, Hex Head 5/16- 18 x 1” - 15 12-00209 2 Capscrew, Hex Head 5/16- 18 x 3/4” - 16 12-00213 4 Capscrew, Hex Head 5/16- 18 x 1 1/4” - 17 15-00202 12 Lock Washer, Helical 5/16 - 18 15-00221 8 Flat Washer 5/16” SAE - 19 15-00708 4 Stud Washer 8.4mm ID x 21mm OD x 4mm - 20 R128442 1 Fan Spacer 4 Bolt 49mm - 21 AT24834 1 Fan 23” (Blower) - 22 12-80049 4 Capscrew, Hex Head Flanged Socket, 10x1.5 x 80mm GR - 24 RE57059 1 Fan Guard - 25 15-70004 4 Snubbing Washer S/S 0.25” ID x 0.84 - 26 19-00032 1 Hose Clamp #32 - 27 R128480 1 Hose, Radiator Outlet - 28 19-00036 1 Hose Clamp #36 - 29 19-00028 1 Hose Clamp #28 - 30 R128455 1 Hose, Radiator Inlet - 31 21-10002 1 Drain Cock, Brass 1/4 NPT - 32 41-01013 1 Hose, Polyvinyl 5/16” ID x 7/16” OD - 33 RE64092 1 Cap, Coolant Fill 10 PSI - 34 00-70082 1 Label, “Northern LIghts” 2’ x 22” -
revised 4/8/10
P1064-3 06/15
GROUP 4 - FUEL SYSTEM
Fuel Injection System
4 - 0
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE531731CDA02
NL1064T23
P1064-3 06/15
GROUP 4 - FUEL SYSTEM
Fuel Injection System
4 - 1
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE533483 1 Fuel Injection Pump 12 Volt (includes keys 2-4, 39) - 2 R91360 1 Nut - 3 R138874 1 Washer - 4 R502076 1 O-ring - 5 R132267 1 Gear - 6 14M7298 3 Flange Nut - 7 RE531802 4 Fuel Injector (includes keys 8-12) - 8 R524623 1 Washer - 9 R56464 1 O-ring - 10 R123593 1 Tube Nut - 11 R51936 1 Sealing Washer - 12 R524841 1 Piston Ring - 13 R123593 2 Tube Nut - 14 AR85519 2 Plug - 15 R97061 4 Tee Fitting - 16 R51936 7 Sealing Washer - 17 R123593 7 Tube Nut - 18 RE531804 2 Tube Assembly, Fuel Return (includes keys 16-17) - 19 RE531805 1 Tube Assembly, Fuel Return (includes keys 16-17) - 20 19M7868 4 Screw - 21 R522965 4 Clamp - 22 R67364 1 Elbow Fitting, 1/8”- 27 NPT x 1/2”-24 UNS - 23 RE60029 1 Adapter Fitting, M12 x 1.5 x 9/16” -24 - 24 51M7040 1 O-ring - 25 RE530778 1 Injection Line, No. 1 - 26 RE530779 1 Injection Line, No. 2 - 27 RE530780 1 Injection Line, No. 3 - 28 RE530781 1 Injection Line, No. 4 - 29 RE19797 2 Clamp - 30 19M6614 3 Capscrew - 31 RE19799 1 Clamp (includes key 30) - 32 51M7041 1 O-ring - 33 RE503242 1 Sensor with Wiring Harness (includes key 32) - 34 RE78048 ** Seal - 35 RE66560 1 Wiring Harness (includes key 34) - 36 T74410 1 Clamp - 37 19M7783 1 Screw, M10 x 16 - 38 22-51004 1 Cold Start Solenoid 12 Volt - 39 R56131 1 Shaft Key -
**As required
NL1064T23
revised 6/15/15
P1064-3 06/15
GROUP 4 - FUEL SYSTEM
Fuel Injection System
4 - 2
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE525490PCDC02
NL1064H23 & NL1064H33
P1064-3 06/15
GROUP 4 - FUEL SYSTEM
Fuel Injection System
4 - 3
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE527528 1 Fuel Injection Pump (includes keys 2-4) - 2 RE516336 1 Fuel Temperature Sensor - 3 R50919 1 O-ring - 4 RE532250 1 Assembly - 5 RE528590 1 Panel Wire Harness (includes key 9) - 6 1 Cap (not available separately) - 7 RE528588 4 Electrical Connector Cap - 8 R134920 8 Nut, M4 - 9 R522630 1 Seal - 10 RE531209 4 Electronic Unit Injector (includes keys 7,8, 11-13) - 11 R522899 ** Sealing Washer - 12 R516647 4 O-ring - 13 R523499 4 Sealing Washer - 14 R520930 1 Bracket - 15 R520813 4 Clamp - 16 RE528096 4 Screw with Washer - 17 26-9940300685 1 Engine Controller NL1064H23 @85 kW - 26-99403006100 1 Engine Controller NL1064H33 @ 100 kW* - 18 19M8320 2 Screw, M10 x 45 - 19 RE527054 1 Fuel Line - 20 T75197 2 Clamp - 21 RE524730 1 Capscrew, M8 x 12 (with pre-applied sealant) - 22 R516125 1 O-ring - 23 14M7298 3 Flange Nut, M8 - 24 R504577 1 Adapter Fitting - 25 R55453 1 O-ring - 26 R502541 1 Gear - 27 R91360 1 Nut, M14 - 28 R116031 1 O-ring - 29 51M7044 1 O-ring - 30 RE517370 1 Fitting (includes key 29) - 31 R523048 1 Bracket - 32 RE527858 4 Capscrew, M6 x 12 (with pre-applied sealant) - 33 19M7868 2 Capscrew, M8 x 30 - 34 RE527055 1 Fuel Line - 35 RE522992 1 Rail (includes keys 36, 39-40) - 36 RE520930 1 Sensor - 37 19M7785 2 Capscrew, M10 x 25 - 38 R522498 1 Bracket - 39 RE515636 4 Restrictor - 40 RE516335 1 Pressure Relief Valve (includes o-ring) - 41 RE526693 2 Fuel Line - 42 RE526692 2 Fuel Line -
*Unit Serial Number must be provided when ordering **As required
NL1064H23 & NL1064H33
P1064-3 06/15
GROUP 4 - FUEL SYSTEM
Fuel Injection System
4 - 4
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved. RE522862PCDC01
NL1064H43
P1064-3 06/15
GROUP 4 - FUEL SYSTEM
Fuel Injection System
4 - 5
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 R91360 1 Hex Nut, M14 - 2 R502541 1 Gear - 3 R55453 1 O-ring - 4 R116031 1 O-ring - 5 R504577 1 Adapter Fitting - 6 14M7298 3 Flange Nut, M8 - 7 R516125 1 O-ring - 8 RE527528 1 Fuel Injection Pump (includes key 9) - 9 RE516336 1 Fuel Temperature Sensor (with part #R50919 o-ring) - 10 19M7868 2 Capscrew, M8 x 30 - 11 RE507538 1 Fuel Line - 12 RE507537 1 Line - 13 RE520930 1 Sensor, Fuel Pressure - 14 RE516335 1 Pressure Relief Valve (with o-ring) - 15 RE515636 4 Restrictor - 16 RE522992 1 Rail (includes keys 13-15) - 17 19M8320 2 Capscrew, M10 x 45 - 18 19M7785 2 Capscrew, M10 x 25 - 19 R522498 1 Bracket - 20 RE507539 2 Fuel Line, No. 1 & 2 - 21 RE507540 2 Fuel Line, No. 3 & 4 - 22 R515044 4 Fitting, M16 x 1.5 x M14 x 1.5 (also order key #25 o-ring) - 23 RE524382 4 Injection Nozzle Assembly (includes keys 24-27) - 24 RE522594 4 Tube - 25 R65397 4 O-ring - 26 R515535 4 Washer - 27 R505452 4 O-ring - 28 R518345 4 Clamp - 29 R504781 4 Capscrew, M8 x 35 - 30 19M7373 2 Capscrew, M5 x 20 - 31 24M7027 2 Washer - 32 RE528486 1 Wiring Harness - 33 R134920 8 Hex Nut, M4 - 34 26-99404006120 1 Engine Controller NL1064H43 @ 120 kW* -
*Unit Serial Number must be provided when ordering.
NL1064H43
P1064-3 06/15
4 - 6
GROUP 4 - FUEL SYSTEM
Primary Fuel Filter
RE531942PCDA01Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064T23
P1064-3 06/15
4 - 7
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 RE529641 1 Fuel Filter Service Kit (includes keys 14-19) - 2 R123594 ** Tube Nut - 3 R74012 ** Sealing Washer - 4 RE60029 1 Adapter Fitting, M12 x 1.5 x 5/16 Tube Compression - 5 51M7040 1 O-ring - 6 RE500576 1 Fitting, M12 x 1.5 (includes key 5) - 7 19M7784 2 Capscrew, M10 x 20 - 8 RE46686 2 Fitting Plug, M12 x 1.5 (includes key 5) - 9 19M7805 1 Capscrew, M10 x 45 - 10 28H2522 1 Spacer - 11 R523930 1 Bracket - 12 19M7785 1 Capscrew, M10 x 25 - 13 RE530620 1 Tube Assembly (includes keys 2-3) - 14 RE526834 1 Seal Kit - 15 RE516512 1 O-ring Pkg. (10 ea.) - 16 RE529643 1 Filter Element (also order o-ring #R113565) - 17 RE516553 1 Seal Kit - 18 RE51650 1 Sediment Bowl - 19 RE519696 1 Harness Assembly with Water Sensor -
**As required
Primary Fuel FilterGROUP 4 - FUEL SYSTEM
NL1064T23
revised 6/15/15
P1064-3 06/15
4 - 8
GROUP 4 - FUEL SYSTEM
Final Fuel Filter and Fuel Lines
RE531928PCDA01Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064T23
P1064-3 06/15
4 - 9
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 RE533453 1 Fuel Filter Service Kit (includes keys 2-6) - 2 RE526834 1 Service Kit - 3 RE516512 1 O-ring Kit (10 ea.) - 4 RE60854 1 Drain Valve - 5 RE522868 1 Filter Element (also order o-ring R113565) - 6 RE516553 1 Seal Kit - 7 RE508575 1 Tube Assembly, Filter Outlet (includes keys 8-9) - 8 R123594 ** Tube Nut - 9 R74012 ** Sealing Washer - 10 RE60029 2 Adapter Fitting, M12 x 1.5 x 5/16 Tube Compression - 11 51M7040 1 O-ring - 12 19M7784 4 Capscrew, M10 x 20 - 13 19M7865 1 Capscrew, M8 x 16 - 14 R116116 1 Bracket - 15 T14050 1 Clamp - 16 14M7298 1 Flange Nut - 17 R505601 1 Bracket - 18 RE46686 2 Plug, M12 x 1.5 - 19 RE515360 1 Tube Assembly, Filter Inlet (includes keys 8-9) -
**As required
Final Fuel Filter and Fuel LinesGROUP 4 - FUEL SYSTEM
NL1064T23
revised 6/15/15
P1064-3 06/15
4 - 10
GROUP 4 - FUEL SYSTEM
Fuel Lines
RE524991PCDA02Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064H23 & NL1064H33
P1064-3 06/15
4 - 11
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 RE46686 4 Plug, M12 x 1.5 - 2 51M7040 1 O-ring - 3 RE500576 1 Fitting, M12 x 1.5 - 4 RE60029 3 Adapter Fitting, M12 x 1.5 x 5/16 Tube Compression - 5 R74012 1 Tube Seal - 6 R123594 1 Tube Nut - 7 RE530620 1 Tube Assembly, Fuel Pump Inlet (includes keys 5-6) - 8 R500270 2 Fitting, M10 x 1.0 x 5/16 Tube Compression - 9 R500271 2 O-ring - 10 RE525786 1 Tube Assembly, Fuel Filter Outlet (includes keys 5-6) - 11 19M7784 1 Capscrew, M10 x 20 - 12 R502287 1 Bracket - 13 T14050 1 Clamp - 14 14M7296 1 Flange Nut, M10 - 15 RE502173 1 Fitting, 900 M10 x 1 x 1/2”-24 - 16 51M7039 1 O-ring - 17 RE523464 1 Tube Assembly, Fuel Leak-off (includes keys 18-19) - 18 R123593 7 Tube Nut, 1/2” - 19 R51936 6 Tube Seal - 20 RE525782 1 Elbow Fitting, M14 x 1.5 x 5/16 Tube Compression - 21 51M7041 1 O-ring - 22 RE529916 1 Tube Assembly, Fuel Leak-off - 23 AR85519 1 Plug - 24 RE524220 1 Fitting - 25 R97061 1 Tee Fitting - 26 RE529914 1 Tube Assembly, Fuel Leak-off (includes keys 18-19) - 27 RE515360 1 Tube Assembly, Fuel Filter Inlet (includes keys 5-6) - 28 R522899 4 Sealing Washer - 29 38M7009 4 Banjo Bolt -
Fuel LinesGROUP 4 - FUEL SYSTEM
NL1064H23 & NL1064H33
revised 6/15/15
P1064-3 06/15
4 - 12
Primary Fuel Filter GROUP 4 - FUEL SYSTEM
NL1064H23 & NL1064H33
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 RE529641 1 Fuel Filter Service Kit (includes keys 7-12) - 2 19M7785 1 Capscrew, M10 x 25 - 3 R523930 1 Bracket - 4 28H2522 1 Spacer - 5 19M7805 1 Capscrew, M10 x 45 - 6 19M7784 2 Capscrew, M10 x 20 - 7 RE526834 1 Seal Kit - 8 RE516512 1 O-ring Pkg. (10 ea.) - 9 RE529643 1 FIlter Element (also order o-ring #R113565) - 10 RE516553 1 Seal Kit - 11 RE51650 1 Sediment Bowl - 12 RE519696 1 Harness Assembly with Water Sensor -
RE527632PCDA01Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
P1064-3 06/15
4 - 13
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 R505601 1 Bracket - 2 19M7784 4 Capscrew, M10 x 20 - 3 RE524723 1 Fuel Filter Service Kit (includes keys 4-8) - 4 RE516553 1 Seal Kit - 5 RE522878 1 Filter Element (also order o-ring #R113565) - 6 RE60854 1 Drain Valve - 7 RE516512 1 O-ring Pkg. (10 ea.) - 8 RE526834 1 Service Kit -
GROUP 4 - FUEL SYSTEM
Final Fuel Filter
RE526225PCDA01Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064H23 & NL1064H33
P1064-3 06/15
4 - 14
GROUP 4 - FUEL SYSTEM
Fuel Lines
RE524991PCDA02Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064H43
P1064-3 06/15
4 - 15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 RE522830 1 Tube Assembly, Fuel Filter Outlet (includes keys 2-3) - 2 R49672 6 Fitting - 3 R67092 6 Sealing Washer - 4 RE502174 1 Elbow Fitting, 900 M14 x 1.5 x 5/8”-24 - 5 51M7041 1 O-ring - 6 RE502173 1 Fitting, 900 M10 x 1 x 1/2”-24 - 7 51M7039 1 O-ring - 8 RE523464 1 Tube Assembly, Fuel Leak-off (includes keys 9-10) - 9 R123593 7 Tube Nut, 1/2” - 10 R51936 6 Sealing Washer - 11 R97061 1 Tee Fitting - 12 RE523629 1 Tube Assembly, Fuel Leak-off (includes keys 9-10) - 13 RE524220 1 Fitting - 14 AR85519 1 Plug - 15 RE523462 1 Tube Assembly, Fuel Leak-off (includes keys 9-10) - 16 RE60028 1 Fitting, M10 x 1 x 1/2”-24 - 17 RE60071 2 Fitting, M10 x 1 - 18 RE522837 1 Tube Assembly, Fuel Filter Inlet (includes keys 2-3) - 19 R516453 2 Fitting, M10 x 1 x 5/8”-24 - 20 R500271 2 O-ring - 21 RE60030 3 Fitting, M12 x 1.5 x 5/8”-24 - 22 51M7040 1 O-ring - 23 RE46686 4 Plug, M12 x 1.5 - 24 RE500576 1 Fitting, M12 x 1.5 - 25 RE523375 1 Tube Assembly, Fuel Pump Inlet (includes keys 2-3) - 26 T13814 1 Clamp -
Fuel LinesGROUP 4 - FUEL SYSTEM
NL1064H43
revised 6/15/15
P1064-3 06/15
4 - 16
Primary Fuel Filter GROUP 4 - FUEL SYSTEM
NL1064H43
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 RE529641 1 Fuel Filter Service Kit (includes keys 4-9) - 2 R523557 1 Bracket - 3 19M7784 4 Capscrew, M10 x 20 - 4 RE526834 1 Service Kit - 5 RE529643 1 Filter Element (also order o-ring R113565) - 6 RE516512 1 O-ring Pkg. (10 ea.) - 7 RE516553 1 Seal Kit - 8 RE51650 1 Sediment Bowl - 9 RE519696 1 Harness Assembly with Water Sensor -
RE523390PCDB01Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
P1064-3 06/15
4 - 17
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 RE526552 1 Fuel Filter Service Kit (includes keys 2-6) - 2 RE526834 1 Service Kit - 3 RE516553 1 Seal Kit - 4 RE516512 1 O-ring Pkg. (10 ea.) - 5 RE526557 1 Fuel Filter (also order o-ring #R113565) - 6 RE60854 1 Drain Valve - 7 19M7785 2 Capscrew, M10 x 25 -
GROUP 4 - FUEL SYSTEM
Final Fuel Filter
RE522836PCDA01Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064H43
P1064-3 06/15
4 - 18
CDP46004
GROUP 4 - FUEL SYSTEM
Fuel Transfer Pump
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064T23
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 RE66153 1 Fuel Pump (includes keys 5-6) - 2 24M7055 2 Washer - 3 RE66298 2 Capscrew, M8 x 30 (includes pre-applied sealant) - 4 R123273 1 O-ring - 5 R500271 2 O-ring - 6 R500270 2 Fitting, M10 x 1.0 x 5/16 Tube Compression - 7 R133405 1 Pin -
P1064-3 06/15
4 - 19
RE506491PCDD01
GROUP 4 - FUEL SYSTEM
Fuel Transfer Pump
Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064H33 & NL1064H43
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 RE517230 1 Fuel Pump (includes key 2) - 2 R123273 1 O-ring - 3 R133405 1 Pin - 4 RE504233 2 Capscrew, M8 x 30 (with pre-applied sealant) -
P1064-3 06/15
4 - 20
GROUP 4 - FUEL SYSTEM
Fuel Filter / Separator
No drawing currently available
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 500FG30 1 Fuel Filter / Water Separator 30 MIC - 2 23-51000 1 Bracket, Racor 500 Mount - 3 21-00753 2 Capscrew, Hex Head M8 x 1.25 x 30mm - 4 15-00701 2 Flat Washer M8 - 5 14-04802 2 Hex Nut, Nylock M8 x 1.5 x 30mm - 6 12-00832 2 Capscrew, Hex Head M10 x 1.5 x 30mm - 7 15-00802 2 Lock Washer, Helical M10 - 8 14-00811 2 Hex Nut M 10 x 1.5 x 30mm - 9 21-50031 1 Female Adaptor, Steel 3/8 NPT x M12 X 1.5 O-R PO - 10 21-50035 1 Male Elbow. 90 , Steel 1/2 O-R Port x 3/8-37 - 11 21-71034 3 Female Swivel, Brass, 3/8 HB x 3/8-37T Push - 12 41-01020 1 Hose 3/8” ID - 40 to + 212 F Push-On - 13 21-52213 1 Elbow . 90 Swivel, Steel 3/8-37T - 14 21-59508 1 Male Connector, Steel 3/8-37T x M12 x 1.5 - 15 21-95932 1 Banjo Fitting, Steel 10mm ID x 1/4-37T - 16 21-59531 1 Banjo Bolt M10 x 1.0 x 30mm - 17 07005-01012 2 Sealing Washer, Bonded M10 - 18 21-71045 1 Female Swivel, Brass, 1/4HB x 1/4-45T - 19 41-01011 37 Hose1/4” ID Push-On - 20 21-01014 1 Male Elbow, 90, Brss 3/8NPT x 1/4-45T - 21 10-51098 1 Manifold, Fuel Line Connection - 22 12-01131 2 Capscrew, Hex Head M6 x 1.0 x 20mm - 23 14-04803 2 Hex Nut, Nylock M6 x 1.0 Class 8 - 24 21-31003 2 Plug, Hex Head, Brass, 3/8 NPT -
added 6/15/15
P1064-3 06/15
4 - 21
GROUP 4 - FUEL SYSTEM
Push-On Fuel Lines
No drawing currently available
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER 1 10-51098 1 Manifold, Fuel Line Connection - 2 12-01131 2 Capscrew, Hex Head M6 x 1.0 x 20mm - 3 14-04803 2 Hex Nut, Nylock M6 x 1.0 Class 8 DIN - 4 21-01015 1 Male Elbow. 90 brass, 3/8 NPT x 3/8-45T - 5 21-01014 1 Male Elbow. 90, Brass 3/8 NPT x 1/4-45T - 6 21-71032 1 Female Swivel, Brass 3/8 HB x 3/8-45T - 7 21-71045 1 Female Swivel, Brass 1/4 HB x 1/4-45T - 8 41-01020 30 Hose 3/8 “ ID -40 to +212 F Push-On - 9 41-01011 37 Hose 1/4” ID Push-On - 10 21-59508 1 Male Connector, Steel 3/8-37T x M12 x 1.5 - 11 21-52213 1 Elbow. 90, Swivel Steel 3/8-37T - 12 21-71034 1 Female Swivel, Brass 3/8HB x 3/8-37T - 13 21-59532 1 Banjo Fitting, Steel 10mm ID x 1/4-37T - 14 21-59531 1 Banjo Bolt M10 x 1.0 x 30mm - 15 07005-01012 3 Sealing Washer, Bonded M10 - 16 21-80002 1 Female Swivel, Steel 1/4 HB x 1/4-37T - 17 21-31003 2 Plug, Hex Head, Brass 3/8 NPT -
added 6/15/15
P1064-3 06/15
GROUP 5 - ELECTRICAL SYSTEMS
Engine Electrical 12 Volt Standard Ground
5 - 0
CDP47439new2
NL1064T23
Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
revised 6/15/15
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 22-41416 1 Wire Harness Assembly - 2 22-42047 3 Relay, SPDT 12 VDC 50 Amp - 22-70083-1 1 Dual Station Relay Board Sub Assembly (see parts detail) - 3 12-00001 4 Machine Screw, PH Phillips #10-32 x 3/4” S/S - 4 14-00006 4 Hex Nut, Nylock #10-32 - 5 22-40915 1 Pressure Switch 15 PSI - 6 22-41016 1 Pressure Sender 0-80 PSI - 7 22-40912 1 Temperature Sender 2500F - 8 22-40364 1 Temperature Switch 2350F - 10 RE68470 1 Starter, 12 Volt Standard Ground - 11 12-80832 1 Capscrew, Hex Head Flanged M10 x 1.5 x 30 mm - 12 13-05001 1 Stud, M10 x 1.5 x 25 mm - 13 14-80811 1 Hex Nut Flanged, M10 x 1.5 - 14 00-40028 1 Grommet, 7/8” I.D. x 1-1/2” O.D. - 15 21-05400 1 Street Tee, Steel 1/8 NPT - 16 22-41080 1 Solenoid 12 VDC 65 Amp Isol. Ground - 17 23-40009 1 Bracket, Solenoid Mounting - 18 19-00060 1 Hose Clamp, #60 - 19 14-00112 2 Hex Nut, Nylock 1/4-20 - 20 1 Alternator -
5 - 1
GROUP 5 - ELECTRICAL SYSTEMS
Engine Electrical 12 Volt Standard Ground
NL1064T23
revised 6/15/15
P1064-3 06/15
GROUP 5 - ELECTRICAL SYSTEMS
Engine Sensors
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE519144 1 Sensor, M20 x 1.5 - 2 51M7044 1 O-ring -
RE59977PCDD01 Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
NL1064T23
5 - 2
P1064-3 06/15
5 - 3
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 22-70083-1 1 Dual Station Relay Board Sub Assembly (see parts detail) - 22-42047 3 Relay, SPDT 12 VDC 50 Amp - 2 12-00001 4 Machine Screw, PH Phillips #10-32 x 3/4” S/S - 3 14-00006 4 Hex Nut, Nylock #10-32 - 4 22-40915 1 Pressure Switch 15 PSI - 5 21-04801 1 Street Elbow, 900 Steel 1/8 NPT - 6 23-40009 1 Bracket, Solenoid Mtg. - 7 19-00060 1 Hose Clamp #60 - 8 22-41080 1 Solenoid 12 VDC 65 Amp - 9 14-00112 2 Hex Nut, Nylock 1/4-20 - 10 15-00121 2 Flat Washer 1/4” SAE - 11 RE70960 1 Starter, 12 V Standard Ground - 12 12-80832 3 Capscrew, Hex Head Flanged M10 x 1.5 x 30 mm - 13 RE533516 1 Alternator 12V/ 75A Standard Ground - 14 AT157679 1 Transient Voltage Protector 12 V -
Engine Electrical 12 Volt Standard Ground
NL1064H23, NL1064H33, NL1064H43
GROUP 5 - ELECTRICAL SYSTEMS
A-11796/ CDP47439new Reproduced by permission of Deere & Co., c2008. Deere & Company. All rights reserved.
P1064-3 06/15
GROUP 5 - ELECTRICAL SYSTEMS
Wire Harness
5 - 4
NL1064H23 & NL1064H33
RE527627PCDA01 Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
P1064-3 06/15
5 - 5
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE529501 1 Wiring Harness (includes keys 2-17) - 2 57M7305 1 Electrical Connector Assembly (also order (2) of 57M7285, 57M7307, - R78064, and (2) R78059) - 3 57M7280 1 Electrical Connector Assembly (also order 57M7274, (3) R78064, - use with 57M7305) - 4 57M8518 1 Electrical Connector Housing (also order (21) 57M8530, (5) of - 57M8531, 57M8528, (3) 57M8605, and (3) 57M8604) - 5 57M8601 4 Electrical Connector Housing (also order (2) 57M8560, 57M8633, - and (2) 57M8566) - 6 57M9005 1 Electrical Connector Housing (also order (3) R104701) - 7 57M8400 1 Electrical Connector Assembly (also order (2) 57M8559 and (2) - 57M8568) - 8 57M8403 1 Electrical Connector Housing (also order (2) 57M8404 and (2) - 57M8406) - 9 57M8407 1 Electrical Connector Housing (also order (3) 57M8135, 57M8417, - and (3) 57M8568) - 10 57M7254 1 Electrical Connector Assembly (also order (2) 57M7494, 57M7289, - and (2) 57M7493) - 11 RE12362 1 Electrical Connector Assembly (also order R78064, use with key 12) - 12 R78052 1 Electrical Connector Assembly (also order R78061 and R78059) - 13 57M8746 1 Electrical Connector Housing (also order (6) 57M7546, 57M8011, - and (2) R78069) - 14 57M7257 1 Electrical Connector Housing (also order (3) R104919, 57M7289, - (2) 57M7258, and 57M7493) - 15 57M7255 1 Electrical Connector Terminal (also order 57M7290 and (3) 57M7259, - use with key 16) - 16 57M7257 1 Electrical Connector Housing (also order 57M7290 and (3) 57M7259, - use with key 17) - 17 57M7255 1 Electrical Connector Terminal (also order (3) 57M7494, 57M7290, - and (3) 57M7493) - 18 R522834 1 Bracket - 19 19M7784 2 Capscrew, M10 x 20 - 20 19M7865 4 Capscrew, M8 x 16 - 21 14M7298 5 Flange Nut, M8 - 22 19M7800 3 Capscrew, M8 x 50 - 23 R523353 1 Bracket - 24 19M7866 1 Capscrew, M8 x 20 - 25 R522575 1 Bracket - 26 RE524730 2 Capscrew, M8 x 12 - 27 RE527858 1 Capscrew, M6 x 12 -
Wire Harness
NL1064H23 & NL1064H33
GROUP 5 - ELECTRICAL SYSTEMS
P1064-3 06/15
GROUP 5 - ELECTRICAL SYSTEMS
Wire Harness
5 - 6
NL1064H43
RE523446PCDE02 Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE531302 1 Wiring Harness - 2 14M7298 4 Flange Nut, M8 - 3 T27550 1 Clip - 4 19M7865 3 Capscrew, M8 x 16 - 5 57M7305 1 Electrical Connector Assembly (also order 57M7277, 57M7285, - 57M7307, R78063, R78059, and R78064) - 6 57M7280 1 Electrical Connector Assembly (also order 57M7274, and (3) R78064) - 7 19M7800 2 Capscrew, M8 x 50 - 8 T38377 1 Clamp - 9 57M8523 1 Electrical Connector Housing (also order (19) 57M8530, (6) - 57M8531, 57M8528, (5) 57M8605, and (2) 57M8604) -
P1064-3 06/15
5 - 7
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
10 57M8518 1 Electrical Connector Housing (also order (9) 57M8530, (8) 57M8531, - 57M8528, and (15) 57M8605) - 11 57M8601 2 Electrical Connector Housing (also order (2) 57M8560, 57M8633, - and (2) 57M8566) - 12 57M8625 1 Electrical Connector Housing (also order (3) 57M8560, 57M8624, - and (3) 57M8566) - 13 19M7866 1 Capscrew, M8 x 20 - 14 57M8601 1 Electrical Connector Housing (also order (2) 57M8602, 57M8633, and - (2) 57M8603) - 15 57M8400 1 Electrical Connector Assembly (also order (2) 57M8559 and (2) - 57M8568) - 16 57M8403 1 Electrical Connector Housing (also order (2) 57M8404 and (2) - 57M8406) - 17 57M8407 1 Electrical Connector Housing (also order (3) 57M8135, 57M8417, - 57M8568, and (2) 57M7833) - 18 R522575 1 Bracket - 19 RE524730 4 Capscrew, M8 x 12 - 20 57M8635 1 Electrical Connector Housing (also order (2) N282070, 57M7546, - 57M8016, and R78069) - 21 57M8625 2 Electrical Connector Housing (also order (3) 57M8618, 57M8624, - and (3) 57M8566) - 22 57M7254 1 Electrical Connector Assembly (also order (2) 57M7494, 57M7289, - and (2) 57M7493 - 23 R522184 1 Bracket - 24 24M7088 2 Washer - 25 19M8618 2 Capscrew, M6 x 12 - 26 57M8634 1 Electrical Connector Housing (also order (6) 57M7546 and 57M8013) - 27 R78052 1 Electrical Connector Assembly (also order R78061 and R78059) - 28 RE12362 1 Electrical Connector Assembly (also order R78064) - 29 57M8601 2 Electrical Connector Housing (also order (2) 57M8618, 57M8633, and - (2) 57M8566) - 30 57M8595 2 Electrical Connector Terminal - 31 57M8594 1 Electrical Connector Terminal - 32 R520873 1 Bracket - 33 57M7257 1 Electrical Connector Housing (also order 57M7290 and (3) 57M7259, use with key 34) - 34 57M7255 1 Electrical Connector Terminal (also order (3) 57M7494, 57M7290, and - (3) 57M7493) - 35 57M8552 1 Electrical Connector Housing (also order (5) 57M8598 and 57M8555) - 36 57M8612 1 Electrical Connector Housing (also order (2) 57M8618, 57M8633, and (2) 57M8566) - 37 57M8639 1 Electrical Connector Housing (also order (2) 57M8165, 57M8022) - 38 57M8542 1 Electrical Connector Housing (also order (2) 57M8564, (2) 57M8567, - and 57M7743) 39 T20280 2 Washer - 40 R523187 1 Bracket - 41 19M7785 2 Capscrew, M10 x 25 - 42 R73291 2 Clamp - 43 R522771 1 Bracket - 44 RE527858 4 Capscrew, M6 x 12 - 45 R522182 1 Bracket - 46 19M7864 2 Capscrew, M8 x 12 -
Wire HarnessNL1064H43
GROUP 5 - ELECTRICAL SYSTEMS
P1064-3 06/15
GROUP 5 - ELECTRICAL SYSTEMS
Engine Sensors
5 - 8
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE525016 1 Thermocouple, Air Temperature - 2 16-00005 1 O-ring - 3 RE52722 1 Coolant Temperature Sensor (also order o-ring #51M7044) - 4 RE519144 2 Engine Speed Sensor - 5 51M7044 2 O-ring - 6 RE167207 1 Oil Pressure Sensor (on cylinder block) - 7 R517471 1 Timing Wheel -
RE527631PCDA01 Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064H23 & NL1064H33
P1064-3 06/15
GROUP 5 - ELECTRICAL SYSTEMS
Engine Sensors
5 - 9
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE525016 1 Thermocouple, Air Temperature (includes key 2) - 2 16-00005 1 O-ring - 3 RE522723 2 Manifold Air Pressure Sensor - 4 21-00132 1 Bushing, Brass 1/4 NPT x 1/8 NPT - 5 RE522824 1 Temperature Sensor, Exhaust Gas Recirculation - 6 RE522823 2 Air Temperature Sensor - 7 RE52722 1 Coolant Temperature Sensor (also order o-ring #51M7041) - 8 RE167207 1 Oil Pressure Sensor (on cylinder block) - 9 RE519144 2 Engine Speed Sensor (includes key 10) - 10 51M7044 2 O-ring - 11 R517471 1 Timing Wheel -
RE523388PCDB01 Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064H43
P1064-3 06/15
GROUP 5 - ELECTRICAL SYSTEMS
Alternator and Mounting
5 - 10
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 AT173624 1 Alternator, 12V / 65 Amp - 2 12M7132 1 Washer - 3 14M7296 1 Flange Nut, M10 - 4 R501486 1 Pulley - 5 T158584 1 Fan - 6 14M7158 1 Hex Nut, M16 - 7 21M7198 1 Capscrew, M5 x 8 - 8 12M7075 1 Washer - 9 H144095 1 Capacitor - 10 H144094 1 Voltage Regulator - 11 14M7297 2 Hex Nut, M5 - 12 14M7273 1 Hex Nut, M8 - 13 RE505090 1 Wiring Harness - 14 R64525 1 Thrust Washer - 15 19M7812 1 Capscrew, M10 x 100 - 16 19M7868 1 Capscrew, M8 x 30 - 17 R48808 1 Washer - 18 12M7064 1 Washer - 19 12M7056 1 Lock Washer - 20 R132167 1 Strap - 21 19M7786 5 Capscrew, M10 x 30 - 22 14M7296 3 Flange Nut, M10 - 23 R132166 1 Bracket - 24 19M7785 2 Capscrew, M10 x 25 - 25 R100377 1 Bushing -
CDP45996A Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064T23 Early Production
P1064-3 06/15
GROUP 5 - ELECTRICAL SYSTEMS
Alternator and Mounting
5 - 11
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 RE533516 1 Alternator, 12V / 75 Amp (formerly #AT173624) - 2 12M7132 1 Washer - 3 14M7296 1 Flange Nut, M10 - 4 RE516489 1 Pulley - 5 R505711 1 Fan - 6 14M7158 1 Hex Nut, M16 - 7 21M7198 1 Capscrew, M5 x 8 - 8 12M7075 1 Washer - 9 RE533941 1 Capacitor - 10 RE533942 1 Voltage Regulator - 11 14M7297 2 Hex Nut, M5 - 12 14M7273 1 Hex Nut, M8 - 13 RE505489 1 Wiring Harness - 14 R64525 1 Thrust Washer - 15 19M7812 1 Capscrew, M10 x 100 - 16 19M8291 1 Capscrew, M8 x 35 - 17 R501065 1 Washer - 18 12M7064 1 Washer - 19 12M7056 1 Lock Washer - 20 R132167 1 Strap - 21 19M7786 5 Capscrew, M10 x 30 - 22 14M7296 3 Flange Nut, M10 - 23 R132166 1 Bracket - 24 19M7785 2 Capscrew, M10 x 25 - 25 R100377 1 Bushing -
CDP45996A Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064T23 Late Production
P1064-3 06/15
GROUP 5 - ELECTRICAL SYSTEMS
Alternator and Mounting
5 - 12
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 AT173624 1 Alternator, 12V 65 Amp (now RE533516) - 2 R48808 1 Washer - 3 19M7868 1 Capscrew, M8 x 30 - 4 T158584 1 Fan - 5 R501486 1 Pulley - 6 12M7132 1 Washer - 7 14M7158 1 Nut, M16 - 8 19M7812 1 Capscrew, M10 x 100 - 9 R64525 1 Thrust Washer - 10 14M7296 1 Flange Nut, M10 - 11 14M7297 1 Nut, M5 (use with o-ring #RE505489) - 12 RE505489 1 Wiring Harness - 13 R74993 1 Boot - 14 H144095 1 Capacitor (not shown) - 15 H144094 1 Voltage Regulator (not shown) - 16 R520917 1 Bracket - 17 19M7786 6 Capscrew, M10 x 30 - 18 14M7296 3 Flange Nut, M10 - 19 R520916 1 Bracket - 20 R134010 1 Bushing - 21 19M7944 1 Capscrew, M10 x 120 - 22 19M7785 2 Capscrew, M10 x 25 - 23 19M8162 2 Capscrew, M10 x 40 - 24 R522949 1 Bracket (only for NL1064H23 & NL1064H33) -
RE509779PCDD01&RE528424PCDB01 Reproduced by permission of Deere & Co., c2009. Deere & Company. All rights reserved.
NL1064H33 and NL1064H43
revised 6/16/15
P1064-3 06/15
added 6/16/15GROUP 5 - ELECTRICAL SYSTEMS
Drive Belt Applications
KEY PART NUMBER QTY DESCRIPTION
Standard Alternators 12V/ 65 Amp or 12V/75A
R123462 1 Drive Belt, NL1064T23 R135589 1 Drive Belt, M1064H23 - NL1064H33 R505186 1 Drive Belt, NL1064H43 Optional Idler (Applications Without Alternator) R123461 1 Drive Belt, L- M- NL1064D (non-turbo) R123457 1 Drive Belt, M1064T1- T2- A- H (with turbo)
1 Drive Belt 1 Drive Belt
5 - 13
RGP6132
P1064-3 06/15
Notes
5 - 14
P1064-3 06/15
GROUP 5 - ELECTRICAL SYSTEMS
S-PVB Powerview Control Panel
5 - 15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 39-40034 1 Enclosure, 10 x 8 x 4 - 2 00-90094 1 Label, S-PVB - 3 37-90086 1 Powerview Module - 4 22-40193 1 Terminal Strip - 5 12-90005 2 Machine Screw, Round Head #6-32 x 32” - 6 15-00009 2 Lock Washer, Helical #6 - 7 14-00019 2 Hex Nut, #6-32 x 1/2” - 8 22-41051 2 Toggle Switch, SPDT - 9 00-40028 1 Grommet - 10 22-99514 1 Resistor Assembly 1.3 k Ohm, 2 watt -
A-11807/ B-9608
P1064-3 06/15
GROUP 8 - FRAMES AND MOUNTING
8 - 0
A-8047A, A-8085A/ D-3178A
Base Frame with Centerbonded Mounts
NL1064T23
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 39-81002 2 Side Rail - 2 39-81014 1 Engine Support - 3 39-81004 1 Generator Support - 4 23-81035 1 Bracket, Front Engine Mounting, Right Hand - 5 23-81036 1 Bracket, Front Engine Mounting, Left Hand - 6 23-81037 2 Bracket, Engine Support - 7 12-80513 8 Capscrew, Hex Head Flanged 1/2 -13 x 1 -1/4" - 8 12-80514 4 Capscrew, Hex Head Flanged 1/2 -13 x 1 -1/2" - 9 14-00502 12 Lock Nut, Plain Flanged 1/2 -13 - 10 12-04803 2 Capscrew, Hex Head, M16 x 2.0 x 40 mm - 11 15-01000 4 Lock Washer, Helical M16 - 12 12-01512 1 Capscrew, Hex Head, M16 x 2.0 x 70 mm - 13 12-01504 1 Capscrew, Hex Head, M16 x 2.0 x 60 mm - 14 01643-31645 2 Flat Washer M16 - 15 14-01432 2 Hex Nut M16 x 2.0 - 16 12-00034 2 Capscrew, Hex Head, 5/8 -11 x 3 -1/2" - 17 15-01330 2 Flat Washer 5/8" SAE - 18 15-00015 2 Head Washer - 19 33-81002 2 Centerbonded Mount, 500 Lbs. - 20 15-00025 2 Tail Washer - 21 14-00912 2 Hex Nut, Nylock - 22 12-00034 2 Capscrew, Hex Head, 5/8 -11 x 3 -1/2" - 23 15-01330 2 Flat Washer 5/8" SAE - 24 15-00015 2 Head Washer - 25 33-81008 2 Centerbonded Mount, 650 lbs. - 26 15-00025 2 Tail Washer - 27 14-00912 2 Hex Nut, Nylock - 28 12-00814 12 Capscrew, Hex Head, M10 x 1.5 x 35 mm - 29 15-00802 12 Lock Washer, Helical M10 - 30 12-00312 8 Capscrew, Hex Head, 3/8 -16 x 1" - 31 15-00302 8 Lock Washer, Helical 3/8 -
GROUP 8 - FRAMES AND MOUNTING
Base Frame with Centerbonded Mounts
8 - 1
NL1064T23
P1064-3 06/15
GROUP 8 - FRAMES AND MOUNTING
8 - 2
A-11797/ D-4354
Base Frame with Centerbonded Mounts
NL1064H23, NL1064H33, & NL1064H43
P1064-3 06/15
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER
1 39-89406 2 Side Rail - 2 39-81014 1 Engine Support - 3 39-89407 1 Generator Support - 4 23-81035 1 Bracket, Front Engine Mounting, Right Hand - 5 23-81036 1 Bracket, Front Engine Mounting, Left Hand - 6 23-81037 2 Bracket, Engine Support - 7 12-80513 8 Capscrew, Hex Head Flanged 1/2 -13 x 1 -1/4" - 8 12-80514 4 Capscrew, Hex Head Flanged 1/2 -13 x 1 -1/2" - 9 14-00502 12 Lock Nut, Plain Flanged 1/2 -13 - 10 12-04803 2 Capscrew, Hex Head, M16 x 2.0 x 40 mm - 11 15-01000 4 Lock Washer, Helical M16 - 12 12-01512 1 Capscrew, Hex Head, M16 x 2.0 x 70 mm - 13 12-01504 1 Capscrew, Hex Head, M16 x 2.0 x 60 mm - 14 01643-31645 2 Flat Washer M16 - 15 14-01432 2 Hex Nut M16 x 2.0 - 16 12-00034 2 Capscrew, Hex Head, 5/8 -11 x 3 -1/2" - 17 15-01330 2 Flat Washer 5/8" SAE - 18 15-00015 2 Head Washer - 19 33-81002 2 Centerbonded Mount, 500 Lbs. - 20 15-00025 2 Tail Washer - 21 14-00912 2 Hex Nut, Nylock - 22 12-01222 2 Capscrew, Hex Head, 3/4-10 x 4” - 23 15-01211 2 Flat Washer 3/4” USS - 24 15-85000 2 Head Washer - 25 33-81011 2 Centerbonded Mount, 800 lbs. - 26 15-85001 2 Tail Washer - 27 14-01212 2 Hex Nut, Nylock 3/4-10 - 28 12-00814 12 Capscrew, Hex Head, M10 x 1.5 x 35 mm - 29 15-00802 12 Lock Washer, Helical M10 - 30 12-00332 8 Capscrew, Hex Head, 3/8 -16 x 1" Grade 8 Plate - 31 15-00307 8 Lock Washer, Helical 3/8 M10 Hardened -
GROUP 8 - FRAMES AND MOUNTING
Base Frame with Centerbonded Mounts
8 - 3
NL1064H23, NL1064H33, & NL1064H43
P1064-3 06/15
4420 14th Ave. NW., Seattle WA 98107 Tel: (206) 789-3880 • 1-800-762-0165 • www.northern-lights.comNorthern Lights and Lugger are registered trademarks of Northern Lights, Inc. © 2015 All rights reserved. Litho USA.