Part Modeling Intro - Iowa State Universityhome.engineering.iastate.edu/~jcshahan/Inventor...
-
Upload
phungxuyen -
Category
Documents
-
view
221 -
download
1
Transcript of Part Modeling Intro - Iowa State Universityhome.engineering.iastate.edu/~jcshahan/Inventor...
Part Modeling IntroUsing Autodesk Inventor
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
1.INITIALIZATION
General things to consider
Follow specific instruction for the class
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
a. Startup
Start Inventor
Verify projectSelected Project
Workspace
Libraries
Folder Options
3/22/2014 Inventor - Assembly Model Intro -jcS
c. Options - General
Application Options:
Inventor - Part Model Intro
Note: • other possibilities.• Carefully adjust (only if needed)
3/22/2014 Inventor - Part Model Intro - jcs
d. Options - Part
Application Options:
Inventor - Part Model Intro
Note: • Optional setting• You may prefer another choice• Other possibilities
3/22/2014 Inventor - Part Model Intro - jcs
e. Options - Sketch
Application Options:
Inventor - Part Model Intro
Note: • other possibilities• Selectively change• Remember what you change
3/22/2014 Inventor - Part Model Intro - jcs
f. Options - Colors
Application Options:
Inventor - Part Model Intro
Note: Other possibilities
3/22/2014 Inventor - Part Model Intro - jcs
b. Adjust Display
Reference PlanesSelect:<Ctrl>+<lmb>
Visibility
ViewHome
Other
Navigation
Pan
Zoom
Orbit
View Face
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
a. Sketch Plane
Pick:
Pick: Create Sketch
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
b. Sketch
Front
SketchLine
Three Point Arc
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
c. Dimension
SketchGeneral Dimension
Inventor - Part Model Intro
Note: Fully Constrained
3/22/2014 Inventor - Part Model Intro - jcs
d. Constraints
<RMB>Show All Constraints
SketchTangent
Vertical
Parallel
Perpendicular
Coincident
Inventor - Part Model Intro
Note: Fully Constrained
3/22/2014 Inventor - Part Model Intro - jcs
e. Finish Sketch
Finish Sketch
Home View
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
f. Extrude
ModelExtrude
Profile
Join
Direction
Distance
OK
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
a. Initialize
Pick: Front Face
Pick: Create Sketch
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
b. Sketch
SketchCenter Point Circle
Center Point
Diameter:
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
c. Dimension
SketchGeneral Dimension
Inventor - Part Model Intro
Note: 2 dimensions needed
3/22/2014 Inventor - Part Model Intro - jcs
d. Constraint
<RMB>Show all Constraints
SketchEqual
Horizontal
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
e. Extrude
Home View
Finish Sketch
ModelExtrude
Join
Other-previous
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
a. Initialize
Home View
New Sketch
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
b. Sketch
Front
SketchCircle
Center point
Diameter
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
c. Sketch (Cont)
SketchProject Geometry
Edge (Both)
Inventor - Part Model Intro
Important: Project Geometry allows the edges to be used in the sketch. This will be used to make new features concentric to the edges.
3/22/2014 Inventor - Part Model Intro - jcs
d. Sketch (Cont)
SketchCircle
Center point
Diameter
Inventor - Part Model Intro
Important: Project Geometry allows the edges to be used in the sketch. This will be used to make new features concentric to the edges.
3/22/2014 Inventor - Part Model Intro - jcs
e. Dimension
No additional dimensions required
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
f. Constrain
<RMB> Show All Constraints
SketchConcentric
Equal
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs
g. Extrude
Home View
Finish Sketch
ModelExtrude
Cut
Through All
Inventor - Part Model Intro3/22/2014 Inventor - Part Model Intro - jcs