PAREXTHERM AND PAREXDIRECT ACRYLIC DPR RENDER SYSTEMS STANDARD COLOUR CHART · PDF...

3
93 PAREXTHERM AND PAREXDIRECT ACRYLIC DPR RENDER SYSTEMS STANDARD COLOUR CHART THE CHOICE OF CONFIDENCE Parex Standard Colours are the forty most popular colours chosen by designers. Explore the clarity achieved through the highest quality pigments available. COLOUR MATCHING Due to our unique tinting process we are able to offer the designer an infinite choice of colour options. We are able to match any colour from the BS, RAL, Dulux and other colour systems. We currently have over 30,000 colour formulations and we are able to produce these or new colours within 2 - 3 days subject to manufacturing capacity. DURABILITY Our unique formulation uses 100% acrylic polymers (Do not get confused with a small percentage approx 1 - 2% of silicone added. Silicone added into the acrylic finish provides no discernable benefit and can cause chalking of the surface over time). The acrylic polymeric bonding in our DPR acrylic finishes form a tough surface yet remains pliable and is vapour permeable preventing weather penetration but allowing the building to breath. Parex 100% acrylic finishes stay fresher longer, resisting fading, chalking, and yellowing. In cyclical weathering tests the finishes resist colour wash, peel adhesion and wet abrasion using a stiff brush being scrubbed back and forth. ATTENTION Please note that colours printed on this chart may be subject to variations when reproduced on paper. To obtain a 1 litre colour sample pot or an individual 200 x 200 mm sample please contact Parex. Final colour approval is the responsibility of the customer and should be made after reviewing an actual sample. SOLAR ABSORPTION Please note dark colours with a solar absorption coefficient over 0.7 are more sensitive to colour alteration, efflorescence, lime bloom and to climatic constraints. Ensure that humidity and temperature conditions are taken into account when they are used. If a dark colour is required we strongly recommend you use Parex 600 CLEAR SEALER OR 610 MATT CLEAR SEALER to provide additional protection to your DPR finish from harmful UV light. PLEASE NOTE The shade of the same colour may also differ dependent upon the finishing aspect; e.g. The colour of a Sand Fine finish adjacent to a Swirl Coarse finish in the same colour may appear to look different when viewed next to each other. The colour chart below has been sorted according to colour and reference number:

Transcript of PAREXTHERM AND PAREXDIRECT ACRYLIC DPR RENDER SYSTEMS STANDARD COLOUR CHART · PDF...

93

PAREXTHERM AND PAREXDIRECTACRYLIC DPR RENDER SYSTEMSSTANDARD COLOUR CHARTTHE CHOICE OF CONFIDENCE

Parex Standard Colours are the forty most popular colourschosen by designers. Explore the clarity achieved through thehighest quality pigments available.

COLOUR MATCHING

Due to our unique tinting process we are able to offer the designeran infinite choice of colour options. We are able to match any colourfrom the BS, RAL, Dulux and other colour systems. We currentlyhave over 30,000 colour formulations and we are able to producethese or new colours within 2 - 3 days subject to manufacturingcapacity.

DURABILITY

Our unique formulation uses 100% acrylic polymers (Do not getconfused with a small percentage approx 1 - 2% of silicone added.Silicone added into the acrylic finish provides no discernablebenefit and can cause chalking of the surface over time). Theacrylic polymeric bonding in our DPR acrylic finishes form a toughsurface yet remains pliable and is vapour permeable preventingweather penetration but allowing the building to breath.

Parex 100% acrylic finishes stay fresher longer, resisting fading,chalking, and yellowing. In cyclical weathering tests the finishesresist colour wash, peel adhesion and wet abrasion using a stiffbrush being scrubbed back and forth.

ATTENTION

Please note that colours printed on this chart may be subject tovariations when reproduced on paper. To obtain a 1 litre coloursample pot or an individual 200 x 200 mm sample please contactParex. Final colour approval is the responsibility of the customerand should be made after reviewing an actual sample.

SOLAR ABSORPTION

Please note dark colours with a solar absorption coefficient over0.7 are more sensitive to colour alteration, efflorescence, limebloom and to climatic constraints. Ensure that humidity andtemperature conditions are taken into account when they are used.If a dark colour is required we strongly recommend you use Parex600 CLEAR SEALER OR 610 MATT CLEAR SEALER to provideadditional protection to your DPR finish from harmful UV light.

PLEASE NOTE

The shade of the same colour may also differ dependent upon thefinishing aspect; e.g. The colour of a Sand Fine finish adjacent to aSwirl Coarse finish in the same colour may appear to look differentwhen viewed next to each other. The colour chart below has beensorted according to colour and reference number:

Part 3_Updated_Layout 1 02/10/2010 17:41 Page 95

94

The information provided in this document results from our knowledge of the products and our experience. On-site results may vary, in particularaccording to the product application methods adopted. Where application methods not covered by this document are used, customers must requestspecific additional information and/or carry out a representative test before using the products. The above-mentioned information in no wayconstitutes a warranty relative to the use of the products. Our general terms and conditions of sale shall prevail, in any event, on the informationprovided in this document. Prior to application, customers and users are requested to check that they have the latest version of this document.

COLOURS

SNOWBALL10400(92)

INDIAN SUMMER10434(66)

BAMBOO10425(66)

STEEL GRAY10420(58)

MALTED BROWN10424(43)

MARBLE WHITE10401(90)

ALUMINIUM10445(72)

LIMESTONE10402(71)

MOONSTONE10446(74)

TUNDRA10409(55)

ALMOND10407(73)

CLEAR LINEN10431(81

SLATE10404(50)

CLASSIC CREAM10421(44)

VANILLA CREAM10451(68)

OCHRE10433(69)

CASHMERE10411(49)

GREY MIST10443(65)

CLAY POWDER10452(35)

IVORY10444(86)

The numbers in the brackets () indicate reflective value. The higher the number, the less UV light the colour absorbs.

Due to printing variations the colours indicated on this colour chart are offered as guidance only and should not be relied upon as a true representation of the actual colour of the finish. Colour will varydepending on the type of finish selected. Application by machine spray or texturing will increase the depth of the colour. Variation in colour due to weather, site conditions and method of application should beexpected. For colour verification, request an actual sample in the colour and texture prior to ordering materials. Apply a sample of the finish to be used on the actual substrate before proceeding with theapplication. Due to the variation in applicator techniques, Parex Ltd is not responsible for the appearance or colour correctness of the applied finish. Colour, texture and finish must be verified and approvedby owner prior to application.

DPR FINISHES STANDARDCOLOUR CHART

Part 3_Updated_Layout 1 02/10/2010 17:41 Page 96

95

PEPPER10450(36)

BEIGE DUNE10448(73)

ORIENTAL GOLD10438(44)

TRIANON VELVET10435(77)

LAVENDER10439(52)

MOSS10447(43)

BRUSHWOOD10423(55)

EVENING SHADOW10440(43)

SMOKEY MAUVE10426(55)

SPICE TAN10415(52)

CANYON DAWN10449(61)

CHAMOIS10441(42)

WARM SAND10432(62)

APRICOT10427(64)

PEACHTREE FROST10437(80)

KHAKI10414(60)

SANTA FE ROSE10436(61)

PALE WHITE10430(80)

PEWTER10403(63)

SPICY SUNSET10442(39)

The numbers in the brackets () indicate reflective value. The higher the number, the less UV light the colour absorbs.

Due to printing variations the colours indicated on this colour chart are offered as guidance only and should not be relied upon as a true representation of the actual colour of the finish. Colour will varydepending on the type of finish selected. Application by machine spray or texturing will increase the depth of the colour. Variation in colour due to weather, site conditions and method of application should beexpected. For colour verification, request an actual sample in the colour and texture prior to ordering materials. Apply a sample of the finish to be used on the actual substrate before proceeding with theapplication. Due to the variation in applicator techniques, Parex Ltd is not responsible for the appearance or colour correctness of the applied finish. Colour, texture and finish must be verified and approved byowner prior to application.

This colour chart is a standard range of available colours. Parex are able to offer a bespoke service of colours to match BS, RAL,Dulux or other paint system colours. With a colour choice of over 30,000 formulations, colour choice is never an issue. If you needto colour match, send us a sample and we can!

Part 3_Updated_Layout 1 02/10/2010 17:41 Page 97