Pantech DUO - Re-flashing Wizard Manual

8/7/2019 Pantech DUO - Re-flashing Wizard Manual

1/17

Re-flashing Wizard

Manualfor Pantech DUO

At February 28th, 2007

Pantech, Co. Ltd.


2/17

Pre-step 1: The device should be powered offbefore the re-flashing starts.

The device should bepowered off first beforeyou start re-flashing.


3/17

Pre-step 2: The ActiveSync should be disabled.For Windows 2000 and XP

OR

The ActiveSync connectionshould be disabled toreduce the troubles beforeyou start re-flashing.


4/17

The WMDCconnection should bedisabled to reducethe troubles before

you start re-flashing.

Pre-step 2: The Windows Mobile Device Center(WMDC) should be disabled.For Windows Vista


5/17

5

Pre-step 3: Find the USB/ Data Cable, whichcan be used also for re-flashing

Please find the USB Cable forthe DUO device and notethat:

Green/part to Device,

Red/part to USB Connector inLaptop.


6/17

6

The USB Connectorshould be plugged in toLaptop as in the Red

circle.

Pre-step 4: Plug the USB Connector to Laptop


7/177

Pre-step 5: Ready to start for Re-flashing.

Now you are ready to startthe re-flashing _without_the device connected to

cable yet - as in the Redcircle.


8/178

Step 1: Run the Re-flashing Wizard.

* Go on to the next step


9/179

Press Install button, and you can

install USB driver.

* If you installed the driver ever, you may skipthis step.

Step 2: Install USB driver.


10/17

10

NOW you should make thedevice in the status ofDownload Ready. In order to

achieve this, please power upthe device while you are holdingdown the 2 key as in the REDcircle until you see DownloadReady text on screen as in the

GREEN circle.

Step 3: Make the device in the statusfor Download Ready.


11/17

11

NOW you should connect theUSB Cable/ 16-pin end to thedevice as in the RED circle.

In parallel you can see theDownload Ready text on screenas in the GREEN circle.

Step 4: Connect the USB Cable/ 16-pinend to the device.


12/17

12

Step 5: Re-flashing startswith a Start button pressed.

< Step 5 >

For re-flashing to be started,

please press the button of Startin RED circle first of all.

* Do not check Emergency mode when finishsuccessfully.


13/17

13

Step 6: Re-flashing Complete.


14/17

14

Step 6-1: When finished successfully.

When the re-flashing has finished successfully, you cansee the device boot-up automatically as in the screenshots above left to right.

Then, you need to follow the step guided by WindowsMobile for the initial device set-up.


15/17

15

Step 6-2: Changing the Modem Link to Inactive

and enable ActiveSync USB connection.While your phone was reflashing with the upgrade software, theModem Link was changed to Active mode and the ActiveSync USBconnection was disabled.

To allow the phone to work with Microsoft ActiveSync, do the following.

1. On the phone, Go to Start > Settings > Connections > Modem Link >Select Inactive > Press Done.

2. On the PC, Go to

ActiveSync > Click File > Connection Settings > Check the box forAllow USB Connections. (Win2000 or XP)

Windows Mobile Device Center > Mobile Device Settings >Connection Settings > Check the box for Allow USB Connections.

(Window Vista)


16/17

16

Step 7-1: when going to a failure.

When the re-flashing moves forward to a failure, you dont see anychange the LCD/ display of the device, and you can see Green LED light.

Sorry for this failure!

Now, you should do:

. Exit the re-flashing application.

. Remove the USB cable from the device.

. Remove the battery from the device.

. Then, start again from the beginning

to pre step B on the re-flashing wizard.


17/17

17

Step 7-2: when going to a failure.

Now you have to check Emergency mode on Re-flashing start page.

Then press start button, and Re-flashing will be starting.

Pantech DUO - Re-flashing Wizard Manual

Documents

Transcript of Pantech DUO - Re-flashing Wizard Manual