Paintball Marker Operator’s Manual 5 · This paintball marker is intended for sale to adults 18...
27
WWW.BUYPMI.COM WWW.BUYPMI.COM AT AT Paintball Marker Operator’s Manual 5.3
Transcript of Paintball Marker Operator’s Manual 5 · This paintball marker is intended for sale to adults 18...
WWW.BUYPMI.COM
WWW.BUYPMI.COMATAT
Paintball Marker Operator’s Manual 5.3
Protective goggles and headgear specifically designed for paintball must be wornby all persons within range when a paintball marker is in use. Paintball safetyrules must be followed at all times.
This paintball marker is intended for sale to adults 18 years of age or older only, for use in compliance with all applicable laws and regulations. Adult supervision is recommended at all times whenever a minor is handling this paintball marker. Protective goggles and headgear specifically designed for paintball must be worn by all persons within range when a paintball marker is in use. Paintball safety rules must be followed at all times.
The PMI Piranha® is a paintball marker designed to shoot .68 caliber paintballs foruse in the sport of paintball. Paintball is a recreational and competitive sport playedworldwide. Special equipment used in paintball includes paintball markers, whichare airguns; and paintballs, which are liquid-filled gelatin capsules that mark with abright color. The object of the game is to capture the opposing team’s flag; while onthat quest, players try to mark their opponents to eliminate them from the game.
PMI PIRANHA® OPERATOR’S MANUAL
WWAARRNNIINNGG!�
WWAARRNNIINNGG!�
STATEMENT OF LIABILITYThis PMI Piranha® semi-automatic paintball marker is surrendered by PursuitMarketing, Inc. (PMI), with the express understanding that the purchaser assumes all liability arising out of any unsafe handling of this marker or any action that violates any applicable laws or regulations. PMI assumes no liability for, and shall not be responsible for, any personal injury or loss of property or life resulting fromthe use of this paintball marker under any circumstances, including but not limited to those resulting from intentional, reckless, negligent or accidental discharges.
READ THIS OPERATOR’S MANUAL COMPLETELY BEFORE LOADING, PRESSURIZING, OR OPERATING THE PMI PIRANHA® PAINTBALL MARKER.
PMI Piranha® is a registered trademark of Pursuit Marketing, Inc.
Pursuit Marketing, Inc. (PMI), founded in 1982 and manufacturer of the PMI Piranha®
line of semi-automatic paintball markers, is an industry-leading manufacturer and wholesale distributor with warehouses in key locations throughout the U.S.A. Headquarters: PMI,55 Howard Ave, Des Plaines, Illinois 60018 USA; phone 1.800.579.1633; www.buypmi.com.
WWAARRNNIINNGG!�
This operator’s manual includes several models of the PMI Piranha® paintball marker. Pursuit Marketing, Inc. (PMI,Inc.), reserves the right to modify or change its markers without incurring any obligation to incorporate suchmodifications or changes in any of its products that were sold prior to the modification. The information in thisoperator’s manual may be updated or changed without notice.
This operator’s manual is intended to remain with the paintball marker upon any subsequent transfer of the marker, whether through sale, resale, or furnishing in any manner. An updated or replacement operator’s manual may be obtained from: Pursuit Marketing, Inc., 55 Howard Ave, Des Plaines, IL 60018 USA; phone 1.800.579.1633;www.buypmi.com. Questions about the operation of the PMI Piranha® paintball marker may be directed to Pursuit Marketing Inc., or visit www.buypmi.com for updates regarding your Piranha® purchase.
TABLE OF CONTENTSTOP 6 QUESTIONS ANSWERED……3
PAINTBALL SAFETY RULES .............4
OPERATING INSTRUCTIONS............6
COMPRESSED GAS/AIR....................8
VELOCITY ADJUSTMENT................10
PMI PIRANHA® SPECIFICATIONS .....12
USP Instructions ..........................13
PIRANHA PARTS LOCATION/DIAGRAMS..15
EVO INSTRUCTIONS ......................27
EFORCE INSTRUCTIONS ...............31
MAINTENANCE & LUBRICATION....33
TROUBLESHOOTING.......................41
WARRANTY.......................................45
1 2
THE PMI PIRANHA® PAINTBALL MARKER IS NOT A TOY. MISUSE MAY CAUSE SERIOUS INJURY OR DEATH. EYE PROTECTION DESIGNED FOR PAINTBALL USEMUST BE WORN BY THE USER AND ANY PERSON WITHIN RANGE. READ THISOPERATOR’S MANUAL COMPLETELY BEFORE LOADING, PRESSURIZING, OR OPERAT-ING THE PMI PIRANHA® PAINTBALL MARKER.
TOP 6 QUESTIONS ANSWERED1. Leaks down barrel Make sure marker is cocked before attaching air.
Check cup seal for wear or grooves. Replace if leak continues. See page 36 for more information.
2. Low velocity (to make it shoot harder) 1. Check that air source is adequately filled.
2. Adjust velocity by turning the velocity adjusting
screw clockwise.
3. Remove bolt/hammer assembly and clean it.Clean inside receiver area where bolt/hammerassembly is located. Lubricate all O-rings on bolt assembly with synthetic paintball marker oil.
4. Change to a stiffer hammer spring.See page 10 for complete velocity instructions.
3. Before you change any O-ring Do not replace the Blue Hammer O-ring with a bottle or “seal” O-ring! The marker needs a Piranha® Blue Hammer
O-ring to work properly.
4. Regular Maintenance See page 28-29.
5. What is the “sear release slide?” The sear release slide is a mechanical slide that allows you to re-install your bolt/block/hammer assembly back into your marker without shooting the marker or taking off the grip frame. See Reassembly Procedure on page 29 for more information.
6. Marker doesn’t work out of the box? 1. Is tank filled? All tanks sent through the mail come empty.
2. Is the marker cocked? Always cock marker before airing it up
3. Is safety “off”?4. Is marker charged? See page 27.5. Call us at 1.800.579.1633.
PAINTBALL BASIC SAFETY RULES
SAFETY FIRST!WWAARRNNIINNGG!�
!�!�
!�!�
!�!�
!�!�
!�!�
!�!�
!�!�
!�!�
!�!�
!�!�
THE PMI PIRANHA® PAINTBALL MARKER IS NOT A TOY. MISUSE MAY CAUSE SERIOUS INJURY OR DEATH. EYE PROTECTION DESIGNED FOR PAINTBALL USE MUST BE WORN BY THE USER AND ANY PERSON WITHIN RANGE. READ THIS OPERATOR’S MANUAL COMPLETELY BEFORE LOADING, PRESSURIZING, OR OPERATING THE PMI PIRANHA®
PAINTBALL MARKER.
READ THIS OPERATOR’S MANUAL COMPLETELY BEFORE LOADING, PRESSURIZING, OR OPERATING THE PMI PIRANHA® PAINTBALL MARKER.
Always wear protective goggles and headgear specifically designed for paintball when shooting this or any paintball marker.
Every person within range of an area where a paintball marker is in use must wear protective goggles and headgear specifically designed for paintball.
Operate a paintball marker only in areas where it is safe and lawful to do so.
Misuse of this paintball marker can result in criminal penalties, including jail time.
This marker is intended for sale to adults 18 years of age or older only. Adult supervision is recommended atall times whenever a minor is handling this marker in any manner.
During game play, follow referee’s instructions and all field safety rules. Avoid shooting at a player’s head, neck, or groin area.
Play paintball only where the rules of safe paintball play are followed.
All paintball markers must be chronographed regularly. Adjust marker to shoot paintballs at a velocity less than300 feet per second (fps) and/or that does not exceed the velocity limit set by the paintball park where themarker is in use. Chronograph the marker at regular intervals during the day, as well as any time the air sourceis refilled or changed, any time the barrel is changed, and upon request of any player or game official.
There is always a chance that a paintball is lodged in the barrel of the marker even when it is not visible in thechamber. To check if the marker is unloaded: remove air system and shoot marker in a safedirection. Remove hopper, visually inspect chamber for a paintball, remove and inspect barrel for the presenceof a paintball. Never look down the barrel of any paintball marker once the barrel is screwed into the marker.
Markers with regulators hold pressure even after tank is removed. Shoot marker in a safe direction after tank isremoved to de-gas it completely.
3 4
This paintball marker operates using compressed gas or air at specified pressure ranges. Follow safety
procedures when handling compressed gas or air. All filling of compressed gas or air cylinders must be
done by qualified persons.
Always cock marker before attaching air or gas source to it. Failure to always cock marker before attaching
air to it may cause accidental firing or discharge of paintballs.
Follow the rules of safe marker handling: Keep finger off trigger until ready to shoot. Keep muzzle
pointed in a safe direction. In addition, firmly insert a barrel plug or barrel bag into the muzzle and push
the electronic or mechanical safety “on” when the marker is not in use and when in any non-shooting area.
Paintball markers with electronic frames have extremely sensitve triggers. Take extra safety precautions anytime
handling or shooting an electronic paintball marker. To avoid accidentally firing the marker, keep the marker
off until you are ready to fire.
Never shoot at domestic animals or wildlife.
Never mark objects outside the confines of the game or authorized shooting areas.
Never look down the barrel of the marker.
Never aim or shoot a paintball marker (loaded or unloaded) toward any person who is not wearing protective
goggles and headgear specifically designed for paintball.
Before disassembly, storage, or transport of the marker, remove all paintballs from the marker, barrel, and
loader; remove air source; and remove all gas or air from the marker. Insert barrel plug and put mechanical
safety in “no shoot” position.
Carry marker in case or sturdy bag when in public.
Safely and securely store marker to prevent access to it by unauthorized persons.
1. Attach threaded barrel firmly to marker.
2. At this time, do not attach air source or loader and do notload paintballs into marker.
3. Insert barrel plug firmly into barrel.
4. Pull the cocking knob straight back from the rear of the marker until the cocking mechanism locks back in the cocked position. See Figures1 and 1a. Always cock marker before airing it up. Certain Piranha modelscome equipped with a flush cocking bolt. During cocking the flush cocking rod will recoil or “spring back” into the marker once releasedand will only move slightly during marker operation. See Figures 2 and 2a.
5. Push safety “off”, or turn the marker “on” if it is an electronic triggerframe. See next page.
6. Squeeze the trigger with an even pressure. The cocking knob will snap forward into the uncocked position. Electronic markers must be chargedbefore operation. See page 27.
7. Cock the marker.
Figure 1. Pull Back
Figure 1a. Fully Cocked
Figure 2. Pull Back
Figure 2a. Fully Cocked
The marker contains compressed gas or air when pressurized. Never disassemble marker until removing all gas or air from the system. Rules for safe handling of compressed gas or air must be followed at all times.
Every person within range of an area where a paintball marker is in use must wear protective goggles andheadgear specifically designed for paintball.
PAINTBALL BASIC SAFETY RULES operating the pmi piranha® markerWWAARRNNIINNGG!�
WWAARRNNIINNGG!�
!�!�
!�!�
!�!�
!�!�
!�!�
!�!�
!�!�
!�!�
!�!�
Safety standards information is available from the American Society for Testing and Materials, 100 BarrHarbor Drive, West Conshohocken, PA 19428-2959; phone 1.610.832.9500; www.astm.org. “Standard Practicefor Paintball Field Operation” is publication F1777-97, and “Standard Specification for Eye Protective Devicesfor Paintball Sports” is publication F1776-97; inquire about additional publications which may be available at the time your request is made.
5 6
!�!�
Always cock marker before attaching air source. Marker can discharge ifair source is attached before marker is cocked.
WWAARRNNIINNGG!�
!�!�
Figure 3 Valve-cylinder connection.
Figure 4 Valve-cylinder connection.
COMPRESSED GAS/AIR
The safety is a small mechanical slide on the left side of the marker above the trigger.When the safety is “off,” a red dot is visible on the marker. The trigger can still bepulled if the safety is “on,” but the marker will not fire or de-cock.
E-Force Model: The on/off button on the left side of the frame should be used as safety.See page 25 for eForce on/off button.
EVO Model: When the Active Indicator glows red the marker is ready to fire. See page 23.
operating the pmi piranha® marker
WWAARRNNIINNGG!�
WWAARRNNIINNGG!�
WWAARRNNIINNGG!�
8. Before attaching air source, read and understand the section in this manual on “Compressed Gas/Air” (Found on page 9). Follow safety rules for handling compressed gas/air. If any leak occurs in the marker, refer to troubleshooting guide or to a qualified airsmith. Use only cylinders for compressed gas or air that comply withall applicable laws and regulations, including but not limited to those of the U.S. Department of Transportation,OSHA, Compressed Gas Association, and/or American Society for Testing and Materials.
Bottom line: First check the tank O-ring for rips or tears, then attach the air source by screwing thethreads of the tank or air source adapter into the threaded bottom line ASA at the base of the grip. Make sure marker is cocked before attaching air. If leaks occur, recheck tank O-ring. If damaged, replace.
WHEN COCKING THE PRESSURIZED MARKER, DO NOT RELEASE THE COCKING KNOB UNTIL AFTER THE COCKING MECHANISM HAS LOCKED BACK INTO THE COCKED POSITION; RELEASING THE COCKING KNOB DURING COCKING CAN CAUSE THE MARKER TO SHOOT.
9. With goggles on, test for function after attaching air source: Squeeze the trigger. The marker should shoot airand the cocking knob should cycle forward and back, stopping in the cocked position, after each triggersqueeze, Repeat several times. Flush cocking rods will bobble some, but they will not come out all the way.
The PMI Piranha® semi-automatic marker shoots one paintball for each squeeze of the trigger, and recocks itself after each shot. See page 27 if you have a Piranha with an electronic frame for the different modes of fire.
10. Turn the marker off (E-Force version) or slide safety forward (semi-auto version). Paintballs may then be loaded.
Before disassembly, storage, or transport of the marker, remove air source first, then remove all paintballsfrom the marker, barrel, and loader. Remove all gas or air from the marker. Insert barrel plug and slidethe mechanical safety forward so the safety is engaged and red dot isn’t showing.
The PMI Piranha® paintball marker may be powered by CO2, regulated compressed air, or regulated nitrogen.
THE SAFETY RULES FOR HANDLING COMPRESSED GAS OR AIR MUST BE FOLLOWED AT ALL TIMES.
OPERATING PRESSURE AND INPUT PRESSURE• Operating pressure range: 250 to 1000 p.s.i. on Piranhas without regulators.• Recommended maximum input pressure is 1000 p.s.i.• Do not exceed recommended pressures.• The EVO, EXT and SRT should recock at less than 300 p.s.i. When using a regulator on the
marker, follow the instructions provided by the manufacturer of the regulator.
Do not leave cylinder or pressurized marker in direct sunlight or exposed to heat source. Increasedtemperature will increase the pressure of compressed gas or air to dangerous levels. A Piranha GTI or R6 usually needs 650 p.s.i. to cycle and attain correct velocity. The EVO, SRT and EXT body stylesneed less than 300 p.s.i. to cycle correctly.
DO NOT EXCEED RECOMMENDED INPUT OR OPERATING PRESSURE.
VALVE-CYLINDER CONNECTIONThe valve on a cylinder is to remain screwed into the cylinder; seeFigures 3 and 4. Should it loosen, the cylinder may detach from the valvewith extremely dangerous force. Call manufacturer or take to qualified personnel for inspection.
Every time a cylinder is filled, the connection between the valve andcylinder must be inspected. If any looseness or leak is detected between the valve and the cylinder, do not fill. Drain cylinder andcall manufacturer or take to qualified personnel for inspection.
During filling, if any looseness or leak is detected between the valve and the cylinder, filling must stop immediately. Drain cylinder and call manufacturer or take to qualified personnel for inspection.
7 8
Figure 5 Safety burst disk.
All paintball markers must be chronographed regularly. Adjust marker to shoot paintballs at a velocitythat is less than 300 feet per second (fps) and/or that does not exceed the velocity limit set by thepaintball park where the marker is in use.
Chronograph the marker at regular intervals during the day, as well as any time the air source isrefilled or changed, any time the barrel or any part in the marker is changed, and upon request of any player or game official.
Figure 6. 3/16" allenwrench is used toadjust velocity.
VELOCITY ADJUSTMENT
Figure 7. Clockwise increases velocity.Counterclockwise reduces velocity.
Figure 7a. Lockingdown SRT or EXTvelocity knob.
WWAARRNNIINNGG!�
WWAARRNNIINNGG!�
WWAARRNNIINNGG!�
A COMPRESSED GAS OR AIR CYLINDER IS A PRESSURE VESSEL. FOLLOW RULES FOR SAFE HANDLING OF COMPRESSED GAS OR AIR. ALL FILLING OF COMPRESSED GAS OR AIR CYLINDERS, AND ALL REPAIRS TO AMARKER OR ITS COMPONENTS MUST BE PERFORMED BY QUALIFIED PERSONNEL.
FILLING COMPRESSEDGAS/AIRAn overfill of any compressed gas or air cylinder can cause the safety burstdisk (Figure 5) on the cylinder to burst, or the cylinder itself to rupture.A cylinder may rupture with extremely dangerous force. Use properly rated disk only. Inspect the burst disc for a vent hole. If no hole is present contacta local store or PMI immediately. DO NOT FILL!
A scale must be used for all CO2 fills to prevent an overfill. A pressure gaugemust be used for all compressed gas or air fills to prevent an overfill.
Fills must be performed by qualified personnel. A cylinder must not be filledbeyond the cylinder’s capacity per the U.S. Department of Transportation. Acylinder’s rated capacity appears on the cylinder itself.
DO NOT OVERFILL ANY CYLINDER. AN OVERFILL CAN CAUSE THE SAFETY BURST DISK OR THE CYLINDERITSELF TO RUPTURE.
HYDROSTATIC TESTING DATE
Many cylinders are required by the U.S. Department of Transportation to be hydro-tested at periodic intervals, with the interval varying according to cylinder type. The date of the cylinder’s initial or later testing appears on the cylinder. A cylinder that is out of date for hydrostatic testingmust not be filled or used.
1. Chronograph the marker using standard chronograph procedures and following safety rules. Shootingvelocity will vary based upon many factors, such as paint, weather, and air system.
2. Adjust velocity by using a 3/16" allen wrench to turn the velocity adjuster. See Figure 6. Turn adjusterclockwise to raise velocity. Turn adjuster counter-clockwise to lower velocity. See Figure 7. Turning thevelocity adjuster changes the amount of tension on the hammer spring. The hammer spring may bechanged for additional velocity adjustment; insert stiffer spring to raise velocity and less stiff springto lower velocity (spring tension in order of strongest to weakest: red, blue, white). See next page formore about springs.
3. The EXT comes standard with the DSR Regulator which can directly affect velocity. Most EXT markerswill shoot 280 fps with the regulator set at 300 p.s.i. Turning the pressure up with a 3/32” allenkey should raise velocity. To turn the pressure up, turn the bottom adjustment screw counterclockwise(looking at the bottom of the DSR) with a 3/32” allen wrench. See Figure 8.
4. Chronograph the marker after every velocity adjustment.
5. Chronograph the marker at regular intervals during the day, as well as any time the air source isrefilled or changed, any time the barrel or any part in the marker is changed, and upon request ofany player or game official.
9 10
+ –
Figure 8. Increasingthe pressure on theEXT.
+
COMPRESSED AIR/GAS
–
SAFETYFIRST!Use a Barrel Plug!
VELOCITY ADJUSTMENT SPRINGS
SEE PAGE 29 FOR DISASSEMBLY OR REASSEMBLY INSTRUCTIONS
The hammer spring assembled with the PMI Piranha® paintball marker is intended to provide appropriateshooting velocity for most outdoor paintball game situations and will provide a range of velocities suitable for most conditions. Shooting velocity will vary based upon form of regulated compressed gasor air used to power the marker, outside temperature, and other factors.DO NOT EXCEED A VELOCITY OF 300 FEET PER SECOND (fps).
PMI PIRANHA® SPECIFICATIONS
spring kit instructions1. Never allow the marker to shoot at velocities exceeding 300 FPS.2. Always remove the gas source and all paintballs from your marker before you disassemble any part of it.3. Before changing any component of a paintball marker, fully understand the entire operator’s manual.4. When changing springs or anything else that will alter shooting velocity of the marker, have
appropriate chronograph available for testing results.5. Never shoot marker at the heads of people or animals. Never shoot at anyone not wearing goggles
and head protection approved for paintball games.6. Spring tension in order from strongest to weakest–red, blue, then white
This operator’s manual is provided with several models of the PMI Piranha® paintball marker. Pursuit Marketing,Inc. (PMI), reserves the right to modify or change its markers without incurring any obligation to incorporatesuch modifications or changes in any of its products that were sold prior to the modification. The information in this operator’s manual may be updated or changed without notice.
This operator’s manual is intended to remain with the paintball marker upon any subsequent transfer of the marker, whether through sale, resale, or furnishing in any manner. A replacement operator’s manual may be obtained from Pursuit Marketing, Inc., 55 Howard Ave, Des Plaines, Illinois 60018 USA; phone 1.800.579.1633;www.buypmi.com.
Action:
Paintballs:
Safety:
Barrel Length:
Barrel:
Height:
Length:
Air Source:
Grip:
Tournament grade semi-automatic powered by either N2or CO2
9 inches for Piranha® SRT, R6, GTI; 11 inchesfor EXT and EVO
Threaded and polished aluminum; ported for all models
8 inches (without attached loader):
17 inches overall (with 9 in. barrel and without attachments)
Input Pressure:
Operating Pressure:
Air Source Input:
Mechanical slide or electonic push button/barrel plug
For use only with standard “.68 caliber” (.68-inchdiameter) paintballs. RPS paintballs recommended
Accepts standard connections for CO2, regulated N2, orregulated compressed air
Recommended 250 psi to 1000 psi
Not to exceed 1000 psi
Bottom line ASA accepts standard paintball threading
Durable space age polymer with double trigger & guard
1211
Velocity Adjustment Velocity adjustment is done by adjusting the rear Velocity Screw (25). See page 10 for more information. Extreme velocity adjustment can be made by replacing the Hammer Spring (15). Seepage 11 for more information. Always use a chronograph to make sure your marker is shooting under the legal field limit after each velocity change.
The Cup Seal (7) can be accessed by removing the Puncture Assembly Set Screw (27) and sliding thePuncture Assembly out the front of the marker. Oil the Puncture Assembly with 100% synthetic oilbefore re-installing.
The Orange Thread Guard (71850) on the front of the marker is replaceable with the black oneincluded in the package.
MaintenanceAlways clean all the paintball residue out of the barrel and off the bolt/block/hammer assembly aftereach use. Oil the Blue Hammer O-ring (35) with two drops of 100% synthetic paintball marker oilafter each case of paint through the marker or anytime the hammer is cleaned. Place four drops of oil into the front of the Puncture Assembly (18) and immediately air it up and dry fire a complete12 gram through the marker after every other case of paint or anytime it has sat idle for over six months.
THIS PAINTBALL MARKER RESEMBLES A REAL GUN FROM A DISTANCE.WHEN IN PUBLIC ALWAYS CARRY MARKER IN A BAG AND ALWAYSPLAY PAINTBALL AT INSURED FIELDS.
WWAARRNNIINNGG!�
An optional holster is available from your local paintball store or online dealer.
14
PMI Piranha: USP
The USP has been designed to hold 10rounds of paint in the clip. Slide the SightScrew (31) back and lock it in the rear position to load paint. Rotate the Clip Lock(4) and load paint. Rotate the Clip Lock backto cover the paint and unlock the Sight Screwbefore firing so the Clip Spring (8) can pushpaint into the chamber.
USP SpecificationsThe USP is designed for optimal performance at approximately 250 fps. The velocity will naturally dropas the 12 gram cartridge empties. Always use a chronograph to make sure your marker is shootingunder the legal field limit. Always follow the Basic Safety Rules found on page 4 and 5 of this manual.
INSTRUCTIONS FOR USING YOUR USP
Important Safety InformationThe USP utilizes a slide safety. See page 7 for complete instructions.
12 Gram Cartridges This USP marker is designed for use only with 12 gram CO2 cartridges (not included). Always cockmarker by pulling back the Bolt Grip Slide (13) before airing up. If 12 gram leaks upon installation,continue to tighten the Puncture Knob (3) until the leak stops. Always shoot the 12 gram emptybefore loosening the Puncture Knob.
13
PMI Piranha: USP
3
10
9 7
376
37
1837 2
6061
416
1
8
31
39
40
13
12
34
25
33
17
15
14
35
32
11
59 30
24 29
21 23 23 30
48
47 46
38
29
55
56
57
58
5 44
26
20
19
28
27
62
22
16
1. USP Receiver Body 718002. Thread Guard-Black 718432. Thread Guard-Orange 718503. Puncture Knob 718304. Clip Lock 718205. Field Strip Pin Assembly 100216. Valve Body 100277. Valve Cup Seal Assembly 101278. Clip Spring 718409. Valve Guide 10520
10. Valve Spring 7159711. Minlon Bolt 7166812. Rear Block w/ Cushion 7166213. Bolt Grip Slide 7185114. Hammer Assembly 1002415. Blue Hammer Spring 1035116. Clip Lock Buna O-ring 14-70 7185217. Spring Guide 1030118. Puncture Assembly 7184219. Ball Detent Cap 1010120. Ball Detent 1016021. Single Trigger Frame 7181022. Sear Release Slide 1070223. Grip Left 1070324. Grip Right 1070425. Velocity Screw 1002626. Valve Set Screw 10513
27. Puncture Assembly Set Screw 7185328. Ball Detent Screw 1018029. Trigger Frame Screw 7053730. Grip Screws 1078231. Sight Screw 2001032. Bolt Pin 1029133. Velocity Screw O-Ring 1046034. Rear Block O-Rings 1026035. Blue Hammer O-Ring 1012937. Valve O-Rings 4101037. ASA O-Ring 4101038. Single Trigger 1003139. Clip Spring Cap 7182040. Clip Piston 7184544. Sear 1072146. Safety Slide 1071147. Safety Ball 1073048. Safety Spring 1075055. Trigger Spring 1075256. Sear/Trigger Pin 1076657. Sear Spring Pin 1076758. Sear Spring 1075359. Front Bolt O-Ring 5773860. Clip Lock Ball Bearings 7185561. Clip Lock Spring 7185462. Clip Lock Set Screw 71844
16
Ball Acceptor
Sear ReleaseSlide
Single Trigger
Field Strip Pin
Bolt Grip Slide
VelocityAdjust Screw
Safety Slide
Sight Screw
Puncture Knob
Thread Guard
Shown: PMI Piranha® USP
PMI PIRANHA® PARTS DIAGRAMPMI PIRANHA® PARTS LOCATION
15
PMI High Performance Ported
Barrel
Vertical Feed
10º BottomLine Adapter
Ultra Light Double Trigger
Safety Slide
.45 Grip Double Trigger Frame
Velocity Adjusting Screw
Field Strip Pin
Sear Release Slide
Cocking Knob
Shown: PMI Piranha® R6
PMI PIRANHA® PARTS LOCATION PMI PIRANHA® PARTS DIAGRAM
17 18
13
2533
34
3412
11
3235
1430
24
29
21
23
30
38
29
26
20
19
28
3737 67910373
239
314
1
55
44
558
56 57
46
4748 22
43
42
41 45
40
1517
59
60
1. Milled Receiver Body 716902. 9” Silver Barrel 101453. ASA Slug 716744. Sight Rail 716845. Field Strip Pin Assembly 100216. Valve Body 100277. Valve Cup Seal Assembly 101279. Valve Guide 10520
10. Valve Spring 7159711. Minlon Bolt 7166812. Rear Block w/ Cushion 7166213. Minlon Cocking Rod 7166914. Hammer Assembly 1002415. Blue Hammer Spring 1035117. Spring Guide 1030119. Ball Detent Cap 1010120. Ball Detent 1016021. Double Trigger Frame Assembly 1005222. Sear Release Slide 1070223. Grip Left 1070324. Grip Right 1070425. Velocity Screw 1002626. Valve Set Screw 1051328. Ball Detent Screw 1018029. Trigger Frame Screw 7053730. Grip Screws 1078231. Sight Screw 20010
32. Bolt Pin 1029133. Velocity Screw O-Ring 1046034. Rear Block O-Rings 1026035. Blue Hammer O-Ring 1012937. Valve O-Rings 4101037. ASA Slug O-Ring 4101038. Trigger Assembly 1005039. Barrel O-Ring 1016140. Hose Adapter 7166441. 10” hose 4706242. Bottom line SS screw 4201643. 10˚ Bottom Line Adapter 1077844. Sear 1072145. 90° Elbow 4700046. Safety Slide 1071147. Safety Ball 1073048. Safety Spring 1075055. Trigger Spring 1075256. Sear/Trigger Pin 1076657. Sear Spring Pin 1076758. Sear Spring 1075359. Front Bolt O-Ring 5773860. Standard B/B/H Assembly 71297
RaisedSightRail
Ball Detent
Shown: PMI Piranha® GTI
Vertical Feed
Raised Sight Rail
Ultra Light Double Trigger
Safety Slide
Gas Thru Foregrip
Velocity AdjustingScrew
Field Strip Pin
Sear Release Slide
10˚ Bottom Line Adapter
Cocking Knob
PMI High Performance Ported
Barrel
PMI PIRANHA® PARTS LOCATION
13
25
3334
34
1211
3235
1430
2429
21
2330
38
29
26
20
1928
3737 67910
373
2
39
31 4
1
5544
5
58
56 57
46
4748 22
43
42
41
45
45
40
15
17
16
18
27
3736
59
60
PMI PIRANHA® PARTS DIAGRAM
1. Milled Receiver Body 716902. 9” Barrel 101243. ASA Slug 716704. Sight Rail 716805. Field Strip Pin Assembly 100216. Valve Body 100277. Valve Cup Seal Assembly 101279. Valve Guide 10520
10. Valve Spring 7159711. Minlon Bolt 7166812. Rear Block w/ Cushion 7166213. Minlon Cocking Rod 7166914. Hammer Assembly 1002415. Blue Hammer Spring 1035116. ASA O-ring 1060817. Spring Guide 1030118. Vertical ASA Adapter 7152019. Ball Detent Cap 1010120. Ball Detent 1016021. Double Trigger Frame Assembly 1005222. Sear Release Slide 1070223. Grip Left 1070324. Grip Right 1070425. Velocity Screw 1002626. Valve Set Screw 1051327. ASA Screw 7158028. Ball Detent Screw 1018029. Trigger Frame Screw 70537
30. Grip Screws 1078231. Sight Rail Screws 20010 32. Bolt Pin 1029133. Velocity Screw O-Ring 1046034. Rear Block O-Rings 1026035. Blue Hammer O-Ring 1012936. Screen Filter 7166737. Valve O-Rings 4101037. Gas Thru Grip O-Ring 4101037. ASA Slug O-Ring 4101038. Trigger Assembly 1005039. Barrel O-Ring 1016140. Gas-Thru Foregrip 1078841. 7" SS hose 4701542. Bottom line SS screw 4201643. 10˚ Bottom Line Adapter 4201344. Sear 1072145. 90° Elbows 4700046. Safety Slide 1071147. Safety Ball 1073048. Safety Spring 1075055. Trigger Spring 1075256. Sear/Trigger Pin 1076657. Sear Spring Pin 1076758. Sear Spring 1075359. Front Bolt O-Ring 5773860. Flush Cocking B/B/H Assembly 71298
19 20
.45 Grip Double Trigger Frame
Ball Detent
Shown: PMI Piranha® SRT
PMI PIRANHA® PARTS LOCATION
2
39
1
4
37
11
50
51
52
53 12
13
25A25
17
15
21
43
42
45
41
30
46
29
26
22
40
33
32
310 37
96
28
1920
30
8
31
31
34
14
35
445855
5657
24
23
5
38
47
48
29 16
18
27
45
377
37
3736
59
60
PMI PIRANHA® PARTS DIAGRAM
1. Vertical Feed Receiver 715002. Barrel 101243. Optimized Pressure Chamber 715304. Sight Rail 715705. Field Strip Pin Assembly 100216. Valve Body 716637. Valve Cup Seal Assembly 101278. Vertical Top Tube 715109. Valve Guide 10520
10. Valve Spring 7159711. Red Venturi Bolt 1007312. Flush Cocking Rear Block w/Cushion 7166113. Flush Cocking Rod 1020114. Hammer Assembly 1002415. White Hammer Spring 7159816. ASA O-Ring 1060817. Spring Guide 1030118. Vertical ASA Adapter 7152019. Flat Ball Detent Cap 7148920. Ball Detent 1016021. Double Trigger Frame Assembly 1005222. Sear Release Slide 1070223. Grip Left 1070324. Grip Right 1070425. Thumb Adjust Velocity Screw 1048225A. Velocity Lock Screw 4202926. Valve Set Screw 1051427. ASA Screw 7158028. Ball Detent Screw 1018029. Trigger Frame Screw 7053730. Grip Screws 10782
31. Sight Rail Screws 71581 32. Bolt Pin 1029133. Velocity Screw O-Ring 1046034. Rear Block O-Rings 1026035. Blue Hammer O-Ring 1012936. Screen Filter 7166737. Bolt O-Rings 4101037. Valve O-Rings 4101037. Gas Thru Grip O-Ring 4101037. Optimized Pressure Chamber O-Ring 4101038. Trigger Assembly 1005039. Barrel O-Ring 1016140. Gas Thru Foregrip 1078841. 7" SS hose 4701542. Bottom line SS screw 4201643. 10˚ Bottom Line Adapter 4201344. Sear 1072145. 90° Elbows 4700046. Safety Slide 1071147. Safety Ball 1073048. Safety Spring 1075050. Flush Cocking Guide O-Ring 1021251. C-Clip 1020752. Retaining Washer 1020653. Flush Spring 1020355. Trigger Spring 1075256. Sear/Trigger Pin 1076657. Sear Spring Pin 1076758. Sear Spring 1075359. Front Bolt O-Ring 5773860. Flush Cocking B/B/H Assembly 71298
21 22
PMI HighPerformance
Ported BarrelVertical Feed
Flush Cocking Knob
OptimizedPressure Chamber
Gas ThruForeGrip
Ultra Light Double Trigger
10º BottomLine Adapter
Sear ReleaseSlide
Raised Sight Rail
Field Strip Pin
LockingVelocity Thumb
Adjuster
Milled Body
Safety Slide
.45 Grip Double Trigger Frame
Ball Detent
PURSUIT MARKETING INC.55 Howard AveDes Plaines, IL 60018 USA
First ClassStamp Here
Tape Here
Detach and Mail
WARRANTYREGISTRATION
Vertical Feed
Sight Rail
DSR Regulator
Ultra Light Double Trigger
LockingVelocity Thumb
Adjuster
Field Strip Pin
Sear Release Slide
10˚ Bottom Line Adapter
FlushCocking
Knob
Ball Detent
On/Off Button
PMI PIRANHA® PARTS LOCATION
Shown: PMI Piranha® EXT
23
Adjustable Drop Forward
Low Pressure Gauge
RAM Air Chamber
PMI High Performance Rifled
Barrel
1. Vertical Feed Reciever 715002. Barrel 715603. Ram Air Chamber 715403B. Ram Air Spring 715993C. Ram Air Piston 715793D. Piston O-Ring 106084. Sight Rail 715705. Field Strip Pin Assembly 100216. Valve Body 716637. Valve Cup Seal Assembly 101278. Vertical Top Tube 715109. Valve Guide 10520
10. Valve Spring 7159711. Red Venturi Bolt 1007312. Rear Block w/ Cushion 71661
13. Flush Cocking Rod 1020114. Hammer Assembly 1002415. White Hammer Spring 7159816. ASA O-Ring 1060817. Spring Guide 1030118. Vertical ASA 7152019. Flat Ball Detent Cap 7148920. Ball Detent 1016021. eForce Double Trigger Frame Assembly 5909322. Sear Release Slide 1070223. Grip 7010525. Thumb Adjust Velocity Screw 1048225A. Velocity Lock Screw 4202926. Valve Set Screw 1051427. ASA Screw 71580
On/Off Indicator
Charge Port
!�
Pursuit Marketing, Inc., thanks you for purchasing this high quality PMI Piranha® paintball marker. Please read each ofthe following items and initial that you have read and understood it before operating the PMI Piranha® paintball marker:
1. This paintball marker is intended for sale to adults only, for use in compliance with all applicable laws and regulations.Adult supervision is recommended at all times whenever a minor is handling this paintball marker in any manner.Please initial: ______
2. Always wear protective goggles and headgear specifically designed for paintball when shooting this marker. Please initial: ______
3. Every person within range of an area where a paintball marker is in use must wear protective goggles and headgear specifically designed for paintball. Please initial: ______
4. Operate a paintball marker only in areas where it is safe and lawful to do so. Please initial: ______5 .Misuse of this paintball marker can result in criminal penalties including jail time. Please initial: ______6. Read this operator’s manual completely before loading, pressurizing, or operating the PMI Piranha® paintball marker.
Please initial: ______7. Never aim or shoot a paintball marker toward any person who is not wearing protective goggles and headgear
specifically designed for paintball. Please initial: ______8. During game play, follow referee’s instructions and all field safety rules. Avoid shooting at a player’s head,
neck, or groin area. Please initial: ______9. Play paintball only where the rules of safe paintball play are followed. Please initial: ______
10. All paintball markers must be chronographed regularly. Adjust marker to shoot paintballs at a velocity that is less than 300 feet per second (fps) and that does not exceed the velocity limit set by the paintball park where the marker is in use. Chronograph the marker at regular intervals during the day, as well as any time the air source is refilled or changed, any time the barrel or any part in the marker is changed, and upon request of any player or game official. Please initial: ______
11. This paintball marker operates using compressed gas or air at specified input pressure ranges. Follow safety procedures when handling compressed gas or air. All filling of compressed gas or air cylinders must be done by qualified persons. Please initial: ______
12. Follow the rules of safe marker handling: Keep finger off trigger until ready to shoot. Keep muzzle pointed in a safe direction. In addition, firmly insert a barrel plug into the muzzle and push the mechanical safety “on” when the marker is not in use and when in any non-shooting area. Please initial: ______
THE PMI PIRANHA® PAINTBALL MARKER IS NOT A TOY. MISUSE MAY CAUSE SERIOUS INJURY OR DEATH. EYE PROTECTION DESIGNED FOR PAINTBALL USE MUST BE WORN BYTHE USER AND ANY PERSON WITHIN RANGE. READ THIS OPERATOR’S MANUAL COMPLETELYBEFORE LOADING, PRESSURIZING, OR OPERATING THE PMI PIRANHA® PAINTBALL MARKER.Please initial: ______
WARNING
Please fill out this PMI Piranha® Warranty Registration form entirely, including the checklist and mail it to: Pursuit Marketing, Inc., 55 Howard Ave, Des Plaines, IL 60018 USA, or register online at www.buypmi.com. Save your original sales purchase receipt or packing slip. A copy must accompany the marker when warranty repairs are sought. Consult operator’s manual for warranty information and instructions on obtaining repair service.
PMI PIRANHA® WARRANTY REGISTRATION
Purchaser’s name:
Mailing address:
City, State, Zip:
Phone number:
E-Mail Address:
Age:
Model purchased:
Serial number:
Where purchased:
Date of purchase:
Seller’s name:
Seller’s address:
City, State, Zip:
Purchase price:
(Serial number is located left hand side of marker next to Piranha® logo)
13. Paintball markers with electronic frames have extremely sensitve triggers. Take extra safety precautions anytime handling or shooting an electronic paintball marker. To avoid accidentally firing the marker, keep your finger away from the trigger until you are ready to fire. Please initial: ______
14. Never shoot at domestic animals or wildlife. Please initial: ______15. Never mark objects outside the confines of the game or authorized shooting areas. Please initial: ______16. Never look down the barrel of the marker. Please initial: ______17. Before disassembly, storage, or transport of the marker, remove all paintballs from the marker, barrel, and loader.
Remove air source and all gas or air from the marker. Insert barrel plug and put mechanical safety in “no shoot” position. Please initial: ______
18. Carry marker in case or sturdy bag when in public. Please initial: ______19. Safely and securely store marker to prevent unauthorized access. Please initial: ______
ITIT’S TIME TO PL’S TIME TO PLAAY THE GY THE GAMEAME
Detach and Mail
PMI PIRANHA® PARTS DIAGRAM
24
28. Ball Detent Screw 1018029. Back eforce Trigger Frame Screw 7053729A. Front eForce Trigger Frame Screw 7158230. Grip Screws 1078231. Sight Screws 7158132. Bolt Pin 1029133. Velocity Screw O-Ring 1046034. Rear Block O-Rings 1026035. Blue Hammer O-Ring 1012936. Screen Filter 7166737. Bolt O-Rings 4101037. Valve O-Rings 4101037. Ram Air Chamber O-Ring 4101037. Regulator O-Ring 4101038. Trigger Assembly 7158639. Barrel O-Ring 1016141. 4.4” Hose 4701142. Bottom Line SS Screws 4201643. 10˚ Bottom Line Adapter 7164044. Sear 7159145. 90° Elbow 4700046. Safety Slide 1071147. Safety Ball 1073048. Safety Spring 1075050. Flush Cocking Guide O-Ring 1021251. C-Clip 1020752. Retaining Washer 1020653. Flush Spring 1020354. Drop Forward 71650
55. Trigger Spring 1075256. Trigger/Sear Pin 1076657. Sear Spring Pin 1076758. Sear Spring 1075361. eForce Board Screws 7159262. eForce Board Cover 7159363. eForce Electronic Board 7159464. eForce Solenoid 7159565. 8.4V Rechargeable Battery 7018166. eForce Charge Port Cover 7159667. Low Pressure Gauge 4609068. NGO Top 4160069. Reg Seat Seal 4151770. Poppet O-Ring (013-70) 5797671. Poppet 4150972. Reg Seat Base O-Ring (006-70U) 1016273. DSR Reg Spring 4151074. Reg Seat Base 4150575. Reg Body Mid (black) 4160176. Bottom Swivel (black) 4160277. Bottom Bolt O-Ring (012-70 U) 5764578. Bottom Bolt 4150379. Adjusting Screw 4150481. DSR 10-32 Plug 4150682. Seal Stop O-Ring (002-70) 1025383. Interior Bottom Bolt O-Ring (010-70) 5764594. DSR Regulator 7163095. Flush Cocking B/B/H Assembly 71298
33B 3C
3D 37
109
7
69
68
70
37
73
71
72
75
79
69
74
67
7272
76
7778
94
36
83
31
1
39
2
31
8
4
53
52
51
5011
3759
12
34
34
13
17
15 3325 25A 30
3532
14
29
43 42
54
4541
82
81
5
27
16
2618
6
37
28
1920
61
62
63
64
30
23
29A 66
2284
56 555657
58
21
65
42
44
38
95
PMI PIRANHA® PARTS DIAGRAM
26
35. Blue Hammer O-Ring 1012936. Screen Filter 7166737. Bolt O-Rings 4101037. Valve O-Rings 4101037. Ram Air Chamber O-Ring 4101037. Regulator O-Ring 4101038. Trigger Assembly 7158639. Barrel O-Ring 1016141. 3.75” Hose 4702142. Bottom Line SS Screws 4201643. 10˚ Bottom Line Adapter–Charcoal 7164644. Sear 7159145. 90° Elbow 4700050. Flush Cocking Guide O-Ring 1021251. C-Clip 1020752. Retaining Washer 1020653. Flush Spring 1020354. Drop Forward–Charcoal 7165655. Sear Spring 7159056. Trigger/Sear Pin 1076657. Sear Spring Pin 7158958. Trigger Spring 7158759. Front Bolt O-Ring 5773867. Low Pressure Gauge 4609068. NGO Top 4160069. Reg Seat Seal 41517
70. Poppet O-Ring (013-70) 5797671. Poppet 4150972. Reg Seat Base O-Ring (006-70U) 1016273. DSR Reg Spring 4151074. Reg Seat Base 4150575. Reg Body Mid (black) 4160176. Bottom Swivel (black) 4160277. Bottom Bolt O-Ring (012-70) 1808578. Bottom Bolt 4150379. Adjusting Screw 4150480. Adjusting Screw O-Ring 5760781. DSR 10-32 Plug 4150682. Seal Stop O-Ring (002-70) 5763183. Interior Bottom Bolt O-Ring (010-70) 5764584. Clear EVO Eye 7170285. Smoke EVO Eye 7170386. Board Screws 7159287. Board Cover 7159388. Upper EVO Board 7170689. LCD Board Assembly 7170390. LCD Board Screws 7170791. 8.4 Volt Battery 7018192. Charge Port Cover 7159693. EVO LCD Grip Frame Assembly 7170694. DSR Regulator 7163695. Eye Bushing 71709
33B
3C 3D 376
377
17
30
35
1415 33
25 25A
13
12535251
5011
37
28
139
2
69
68
70
37
73
71
72
75
8079
41 45
30
43
38
42
54
42
69
10
23
29
5
16
26
44
5556
57
34
74
6732
76
77
8281
8
83
9
18
36
7272
78
56
20
24
20
19
2884
88
86 85
8758
22
92 31
90
91
89
59
93
94
95
Vertical Feed
On/Off Button
Adjustable DSR Regulator
FlushCocking
Knob
Sear Release Slide 10˚ Bottom Line Adapter
Electronic Anti-Chop EYE
Shown: PMI Piranha® EVO
Adjustable Drop Forward
Low Pressure Gauge
RAM Air Chamber
PMI High Performance Rifled
Barrel
1. Vertical Feed Receiver–Gold Fade 717222. Barrel–Gold 715643. Ram Air Chamber–Gold 715463B. Ram Air Spring 715993C. Ram Air Piston 715793D. Piston O-Ring 106085. Field Strip Pin Assembly 100216. Valve Body 716637. Valve Cup Seal Assembly 101278. Vertical Top Tube–Gold 715169. Valve Guide 1052010. Valve Spring 7159711. Grey Venturi Bolt 7170212. Rear Block w/ Cushion 7166113. Flush Cocking Rod 1020114. Hammer Assembly 1002415. White Hammer Spring 7159816. ASA O-Ring 10608
17. Spring Guide 1030118. Vertical ASA–Gold 7152719. Left Eye Cover 7170120. Flat Ball Detents 1016022. Sear Release Slide 7158523. LCD Grips 7170424. Right Eye Cover 7170025. Thumb Adjust Velocity Screw 1048225A. Velocity Lock Screw 4202926. Valve Set Screw 1051427. ASA Screw 7158028. Ball Detent/Eye Cover Screws 1078229. Rear Trigger Frame Screw 7158330. Grip Screws 7170531. Front Trigger Frame Screw 7158232. Bolt Pin 1029133. Velocity Screw O-Ring 1046034. Rear Block O-Rings 10260
LCD
Active Indicator
25
PMI PIRANHA® PARTS LOCATION
The Evo is a semi-auto only marker that is designed for tournament play. It does not have full auto or burst features.
SAFETY: When you turn the marker on by holding the on/off button for three seconds, it automaticallygoes into "safe mode." To turn the safety off, press the on/off button once lightly. The red on/off indicator willturn on and the marker is now ready to fire. To turn the marker back on safety, press the on/off button onceand the red active indicator will turn off. To turn the marker off hold the on/off button for three seconds whileit is in safe mode. The frame should be left off when not using the marker or you will drain the battery.
WARNING: Never use water to clean the marker, or yourun the risk of damaging the electronic trigger frame.
00 00Eye
IndicatorCounter/Timer
PMI Piranha: EVO
27
ON/OFF BUTTON: The on/off is the silver button located on the left hand side of the gripframe.Push and hold it in for three full seconds to turn your Evo LCD on. The LCD will turn on, but the marker isin "safe mode." Press the on/off button again and the safety will turn off. The red on/off indicator will thenlight up.
28
ODOMETER: The Evo must be in "safe mode" to view the odometer. Press the A button to viewthe odometer.
TIMER: The Evo must be in "safe mode" to change the timer settings. Press button B on the righthand side once to change settings. Once the numbers are blinking use button A to increase timer clock byone minute increments. Press button B once when the countdown time is set and the numbers will stopblinking. To start the timer, turn the safety off and fire the marker once.
ANTI-CHOP EYE (ACE): When the ACE is activated, it will only allow you to fire whenthere is a paintball in the chamber. When the ACE is off, the rate of fire defaults to a slower setting soyou won't chop paint. However, this means you will not be able to dry fire the marker quickly. To turn theACE on or off, press button B on the right hand side of the frame while the marker is ready to fire. TheEye logo on the LCD will only appear while the ACE is turned on.
LCD DISPLAY
Cleaning The EYE: If the Evo Anti-Chop Eye doesn’t function, then verify that the eye isturned on. If the Eye is on and Evo fires without a paintball in the breach, then there is probably dirt orpaint on the eye itself. Clean off the eyes and test again. It is possible for an authorized repair shop toremove the eye itself for cleaning, but a squeegee should clean away enough paint to make the eyes workright away.
To test Eye function, (treat the marker as though it was
loaded for this test):
1. Turn marker on 2. Cock marker3. Verify that the Eye is on by checking for the Eye Indicator on the LCD4. Remove hopper to make sure there is no paintball in the breach5. The marker should NOT fire when the trigger is pulled
INSTRUCTIONS FOR USING YOUR EVO
PMI Piranha: EVO
EVO Battery: The Evo comes with a 9 volt rechargeable battery. You must charge it for a full22 hours before initial use since it does not come fully charged. For best long term battery life, repeat this process every time it is drained. You can also use a regular 9 volt battery with this frame if yourrechargeable battery is dead or if you want to play with the frame right away. You will need to remove theright grip panel to replace the battery.
Button A
Button BActive Indicator
ODOMETER: Accumulate odometer readout can be zeroed out by holding button B for 15 secondswhile on/off switch is turned to safe mode.
WARNING: Take extra safety precautions when handling or shooting the Evo as paintball markers with electronic frames haveEXTREMELY sensitve triggers.
5
26
8
12
11
3
71
6
10
9
17
13
15
14
16
4
10
18
SHOWN: PMI PIRANHA®
eFORCE GRIP FRAME
PMI PIRANHA® PARTS LOCATION PMI PIRANHA® PARTS DIAGRAM
29 30
1. eForce Polymer Double Trigger Frame Assembly 590932. eForce Sear Release Slide 715853. Grip 701054. Rear Trigger Frame Screw 715835. Front eForce Trigger Frame Screw 715826. Grip Screws 107827. eForce Trigger 715868. eForce Sear 715919. eForce Trigger Spring 71587
10. eForce Sear/Trigger Pin 7158811. eForce Trigger/Spring Pin 7158912. eForce Sear Spring 7159013. eForce Board Screws 7159214. eForce Board Cover 7159315. eForce Electronic Board 7159416. eForce Solenoid 7159517. eForce Charge Port Cover 7159618. 8.4V Rechargeable Battery 70181
Burst Button
Full Auto Button
Sear
Sear Release SlideOn/Off Button
Charge Port
On/Off Indicator
Double Trigger FrameAssembly
eForce SS Hose LengthsR6– 10” 47062GTI– 6.25” 47097SRT– 6.25” 47097EXT– 3.75” 47021
Tournament Lock(See Page 28)
Blinking Lightmeans Low Battery
ALWAYS CHARGE WITH MARKER TURNED OFF!
WWAARRNNIINNGG!�
PMI RECOMMENDS THE INCLUDED 9V RECHARGEABLE BATTERY FOROPTIMAL PERFORMANCE. DO NOT USE THE BATTERY CHARGER WHENUSING ANY NON-RECHARGEABLE BATTERY.
PMI PIRANHA® eFORCE
3231
BURST BUTTONPress the Burst Button once to turn the marker on 3 Shot Burst. Press the Burst Button again toturn the frame to 6 Shot Burst. Press the Burst Button again to turn the frame to 9 Shot Burst.Press the Burst Button again to turn it back to semi-auto.
FULL AUTO BUTTONPress the Full Button once to turn the frame to Full Auto. Press the Full Button again to turn itback to semi-auto.
WWAARRNNIINNGG!�
WWAARRNNIINNGG!�
NEVER USE WATER TO CLEAN THE MARKER, OR YOU RUN THE RISKOF DAMAGING THE ELECTRONIC TRIGGER FRAME.
SEAR RELEASE SLIDEThe sear release slide is located on the left hand side of the eForce grip frame. To reinstall thebolt/block/hammer assembly, push the sear release slide up before the hammer comes in contactwith the sear. That will allow the bolt/block/hammer assembly to slide easily into the marker.
INSTRUCTIONS FOR USING YOUR eFORCE FRAME
PMI PIRANHA® eFORCE
ON/OFF BUTTONThe on/off is located on the left hand side of the marker. Push it once to turn your eForce on. Pushit again and the frame will turn off. The frame should be left off when not using the marker or youwill drain the battery. Use the on/off button as the safety.
eFORCE BATTERYThe eForce frame comes with a 9 volt rechargeable battery. You must charge it for a full 22 hourswith the marker turned off before initial use since it does not come fully charged. For best long term battery life, repeat this process every time it is drained. You can also use a regular 9 volt battery with this frame if your rechargeable battery is dead or if you want to play with the frameright away. You will need to remove the right grip panel when you need to replace it. A blinkingon/off indicator light means your eForce frame needs to be charged right away. Always charge withthe marker turned off.
To access the Tournament Lock, you have to take theeForce frame off the receiver and unscrew the two phillipshead screws (#13) that hold the board cover (#14) inplace. Once these are out, the cover can be lifted and thesmall blue switch can be moved to put the marker onTournament Lock.
lock off
lock on
TOURNAMENT LOCK SWITCH
The Tournament Lock Switch enables you to play in a tournament or at a field that does not allow full auto and burst modes by restricting the marker to semi-automatic only. All eForce frames come with theTournament Lock off so you can immediately put themarker in full auto or burst mode.
Battery Indicator Light
Charge Port
Sear Release Slide
On/Off Button
*Adjustable modes of fire and rechargeable frames are not currently available in all countries.
WWAARRNNIINNGG!�
TAKE EXTRA SAFETY PRECAUTIONS WHEN HANDLING OR SHOOTING SINCEMARKERS WITH ELECTRONIC FRAMES HAVE EXTREMELY SENSITVE TRIGGERS.
LUBRICATIONIt is recommended that 100% synthetic paintball marker oil, such as PMI Paintball Gun Oil, be usedfor lubricating the marker. Do not use any oil aside from paintball marker oil or you run the riskof ruining the O-rings.
1. Before each insertion of the removable air source (tank or remote line) into the ASA, clean thethreads and put two drops of oil onto them.
2. After removing the bolt/hammer assembly, clean off any paint or dirt. Put 1 drop of oil ontoeach O-ring. See Figure 13. Only replace the Blue Hammer O-ring (#35) with another BlueHammer O-ring, or the marker will not re-cock properly.
3. Before screwing the barrel onto the marker, clean the barrel threads.
4. The fastest way to oil the entire Piranha® is to take off the barrel; put 6 drops of oil into theASA (#43), screw the bottle in over the oil, and shoot the marker a dozen times without thebarrel.
5. There is no need to ever oil the inside of the barrel. Oil in the barrel will decrease accuracy.
DISASSEMBLY PROCEDURE1. Before disassembling the marker, first remove the air tank, and then remove all paintballs from
the marker, barrel, and loader.
Figure 10. Remove field strip pin to begin disassembly.
DISASSEMBLY
Figure 13 Bolt-hammer assemblyremoved.
Figure 11 Figure 12 Grasp assembly.
LUBRICATION
WWAARRNNIINNGG!�
The PMI Piranha® is easy to strip for cleaning and basic maintenance. Regular cleaning andmaintenance is highly recommended. Keep screws tightened. Replace worn components with factory parts; all leaks must be repaired promptly. Air system repairs are best performed by the factory or an authorized factory repair facility. Contact PMI for information regarding authorized PMI Piranha® repair facilities.
DO NOT ATTEMPT TO PERFORM MAINTENANCE PROCEDURES UNLESS QUALIFIED TO DO SO. DONOT DISASSEMBLE MARKER UNTIL IT IS COMPLETELY DRAINED OF COMPRESSED GAS OR AIR ANDALL PAINTBALLS HAVE BEEN REMOVED. ALL FILLING OF COMPRESSED GAS OR AIR CYLINDERS MUSTBE DONE BY QUALIFIED PERSONS.
CONTACT PMI FOR REPAIR ASSISTANCE AND INFORMATION REGARDING AUTHORIZED PMI PIRANHA®
REPAIR FACILITIES. PHONE 800.579.1633; WWW.BUYPMI.COM
THE PAINTBALL MARKER AIR SYSTEM MUST BE REPAIRED OR REPLACED ONLY WITH THE CORRECT PRESSURE RATED COMPONENTS.
2. Leave barrel plug firmly inserted inbarrel and keep barrel pointed in a safe direction.
3. To remove the bolt/hammer assembly,first remove the field strip pin. SeeFigure 10. The field strip pin is atthe center rear of the receiver and isremoved by pulling it out of the left side of the marker.
4. Grasp the block assembly and slowly begin to pull the bolt/hammer assembly out of the marker.See Figure 11.
5. When the bolt/hammer assembly is about halfway out, grasp it with one hand and continue to hold it intact while removing it completely from the marker. See Figure 12.
33 34
Oil Here
Oil Here
REGULAR MAINTENANCE FOR THE PIRANHA®
1. Clean out all broken paint regularly. Do this before you oil the marker.
2. Oil marker each time you play with synthetic marker oil. Never use 3-in-1. Non-synthetic oil can contaminate the ball detent and hammer O-ring, causing the marker not to function. PMI’s new synthetic oil works the best. See previous page for oiling instructions.
3. The fastest way to oil your Piranha is to drop 6 drops in the ASA (#43) and screw the bottle in over it.Take the barrel off and shoot the marker a dozen times to cycle oil throughout the marker.
4. Inspect the bolt O-rings and Blue Hammer O-ring after each time you oil the marker. Make sure they are getting oil.
5. Clean out the vertical feed, as well as the barrel. If any oil or paint is present, the marker will not shoot accurately.
6. Never wash the bolt assembly with water unless you are going to oil them before you reassemble them.Dry before oiling.
7. Check ball detent (#20) every 25,000 shots. Replace if it is worn or broken.
8. Never stretch hammer spring to increase velocity. This will shorten the life span of the spring.
REASSEMBLY PROCEDURE (sear release slide)
1. See Figures 15 through 26, which shows the procedure for reassembly of the bolt/hammer assembly. The flush cocking bolt reassembly procedure can be found on the following page in figures 27-38. Once it is reassembled,hold the bolt/hammer assembly in one hand. See Figure 24. Push it gently into the marker until it stops sliding forward, which will be about halfway into the body of the marker. See Figure 25.
2. Before it stops sliding forward, push the Sear Release Slide button forward. See Figure 25. The Sear Release Slide button is located on the left side of the marker near the top of the left grip panel. Continue to press assembly intomarker. Pushing the button allows the bolt/hammer assembly to slide easily therest of the way into the marker. The sear release slide has to be pushed up oneForce frames. See Figure 36.
3. Field strip pin must be inserted into the left side of the marker.
4. After reassembly, follow the procedures in this manual for adding air system, loader, and paintballs.
Figure 14
maintenance and reassembly
Figure 22 Figure 23
Figure 24 Figure 25–Semi-Auto Sear Release Figure 26
Figure 18 Figure 19 Figure 20
Figure 21
Figure 17Figure 15 Figure 16
BOLT/HAMMER REASSEMBLY
35 36
Figure 35
Figure 27
FLUSH COCKING BOLT REASSEMBLY
Figure 28 Figure 29
Figure 30 Figure 31 Figure 32
Figure 33 Figure 34
Figure 36–Electonic Sear Release Pictured Figure 37 Figure 38
Figure 41 Figure 42
1/8”AllenScrew
1/8”Allen Screw
BottomLine ASA
CUP SEAL & VALVE REMOVALWWAARRNNIINNGG!�
DO NOT ATTEMPT TO COMPLETELY DISASSEMBLE YOUR PIRANHA® UNLESS QUALIFIED TO DO SO.
CONTACT PMI FOR REPAIR ASSISTANCE AND INFORMATION REGARDING AUTHORIZED PMI PIRANHA® REPAIR FACILITIES. PHONE 1.800.579.1633 WEB WWW.BUYPMI.COM
THE PAINTBALL MARKER AIR SYSTEM MUST BE REPAIRED OR REPLACED ONLY WITH THE CORRECTPRESSURE RATED COMPONENTS.
1. Before disassembling the marker remove the air source, then remove all paintballs from the marker, barrel, and loader.
2. Unscrew the ASA Slug to access the cup seal assembly. See Figure 39. Remove the valve spring,cup seal assembly, and guide as in Figure 40.
37 38
Figure 40Figure 39
3. To remove the bottom line air system, detach the bottom line ASA from the grip by removing the twoscrews (#42). See Figure 41. The 5/32” allen wrench for this procedure is not included with the marker.Then unscrew the vertical grip (#40) or regulator.
Figure 43 Figure 44
5. To access the valve, use a flathead screwdriver to remove the small brass screw located in thecenter of the underside of the receiver (#26). See Figure 43. To remove the valve body, use aflat ended wooden dowel or the eraser end of a pencil to push the valve body out of the frontof the receiver. See Figure 44.
VALVE REMOVAL CONTINUED pure energy vertical regulator
DSR REGULATOR
Questions about the operation of the PMI Piranha® paintball marker may be directed to: Pursuit Marketing,Inc., 55 Howard Ave, Des Plaines, IL 60018 USA; phone 1.800.579.1633 or www.buypmi.com for any updatesregarding your Piranha® purchase.
6. The valve body must be inserted correctly with the raised flat surface of the valve and larger hole pointingtowards the front of the marker. Be careful reinserting the valve body. Any scratches to the front can causeleaks. Use a flat ended wooden dowel or the eraser end of a pencil to push the valve body into the frontof the receiver. See Figure 45. The valve pin assembly must be inserted correctly into the valve; valve pinmust drop down into valve body completely.
39 40
3
2
4
1
6
9
1413
3
866
11
1615
7
5
10
12
17
1. Bottle O-Ring 410102. NGO Top 416003. Reg Seat Seal 415174. Poppet O-Ring (013-70) 579765. Poppet 415096. Reg Seat Base O-Ring (006-700) 101627. Spring 415108. Reg Seat Base 415059. Reg Body Mid (black) 41601
10. Bottom Swivel (black) 4160211. Bottom Bolt O-Ring (012-70) 1808512. Bottom Bolt 4150313. Adjusting Screw 4150414. Adjusting Screw O-Ring 5760715. DSR 14-32 Plug 4150616. Seal Stop O-Ring (002-70) 5763117. Interior Bottom Bolt O-Ring (010-70) 57645
Figure 45
The EXT comes standard with the DSR Regulator which can directly affect velocity. Most EXT markers will shoot 280 fps withthe regulator set at 300 psi. Turning the pressure up with a 3/32” allen key should raise velocity. To turn the pressure up,turn the bottom adjustment screw counterclockwise (looking at the bottom of the DSR) with a 3/32” allen wrench.
Marker must be fired several times for regulator to accept new setting.
NOTE: Make sure marker is un-cocked before continuing to step 4.
4. To remove trigger frame from the receiver, remove the two 1/8” socket allen screws (#29) underthe receiver. One is in front of the trigger guard and one is behind the grip portion of theframe. See Figure 42. The receiver then will disassemble from the trigger frame.
IMPORTANT: Valve body O-rings and front valve portion of the receivermust be well oiled prior to valve body insertion.
Leaks at connection between braided air hose Requires disassembly of air hose assembly for repairs;and fitting contact factory or factory authorized repair center.
Leaks down barrel Check front of cup seal where it touches the valve for any wear or grooves. Replace if leak continues.
DO NOT ATTEMPT TO PERFORM MAINTENANCE PROCEDURES UNLESS QUALIFIED TO DO SO.
THIS TROUBLESHOOTING GUIDE DOES NOT COVER ALL SITUATIONS AN INDIVIDUAL MAY ENCOUNTER.CONTACT PMI FOR REPAIR ASSISTANCE AND INFORMATION REGARDING AUTHORIZED PMI PIRANHA® REPAIRFACILITIES. PHONE 1.800.579.1633 WEB WWW.BUYPMI.COM
THE PAINTBALL MARKER AIR SYSTEM MUST BE REPAIRED OR REPLACED WITH THE CORRECT PRESSURERATED COMPONENTS.
BEFORE DISASSEMBLY OF THE MARKER, REMOVE AIR SOURCE; REMOVE ALL PAINTBALLS FROM THE MARKER, BARREL, AND LOADER.
Leaks at body of marker or heavily down Requires removal of valve and inspectionthe barrel of front valve O-ring (can be replaced with
bottle O-rings), cup seal and valve surface where the cup seal touches the valve. A valve installed backwards will cause a leak. Never use a screwdriver or metal object to remove or install a valve body. Use a pencil eraser or other soft instrument.
Leaks at connection between gas-through Remove foregrip unit and check O-ringsforegrip & vertical ASA Replace with tank O-rings if worn or broken.
Leak in pressure source between tank valve Do not fill cylinder. Immediately take to qualifiedand cylinder personnel for inspection. Cylinder must be drained.
Leaks at connection between ASA and tank Check tank O-ring at connection or on remote hose connector. See page 34.
AIR LEAK
TROUBLESHOOTING
Leaks A: Replace poppet O-rings (#4)Leaks B: De-gas and check O-ring (#16), re-seat and re-thread or carefully apply Loc tite (red or blue)Leaks C: Replace 16 mid body O-ring (#3)Leaks D: Replace 14 bottom bolt O-ring (#11)Leaks E: Re-Teflon tape or Loc tite bottom bolt threads,Check reg seat base O-rings (part #8 on DSR Regulator diagram).
A
B
C E
D
DSR Regulator Leak ChartWWAARRNNIINNGG!�
41 42
TROUBLESHOOTING DSR
NOTE: Any PMI Piranha® with a regulator will need the regulator adjusted properly to get proper recock andadequate velocity out of the marker. Please see pages 10 & 36 for complete velocity instructions.
Trigger pulls back, marker will not shoot Check that the safety slide is back and the red dot is visible. Check that the marker is cocked, air source is correctly attached and air source is properly filled. If the frame is electronic, make sure battery is properly chargedand the trigger frame screws are tight.
Trigger action does not feel smooth Check pin at top of trigger. Use center punch totap pin back into place.
Marker runs on (partially cycles more than Check that air source is correctly attached to once when trigger is squeezed) marker. Check that air source is adequately filled.
Check sear and Blue Hammer O-ring for wear.
VELOCITY
Low Check that air source is adequately filled
Low Adjust velocity adjuster clockwise
Low Remove bolt/hammer assembly and clean it;clean inside receiver area where bolt/hammer assembly is located; lubricate all O-rings on bolt assembly with synthetic paintball marker oil
Low Change to a stiffer hammer spring
High Adjust velocity adjuster counterclockwise
High Change to a softer hammer spring
(DO NOT EXCEED 300 FEET PER SECOND)
TROUBLESHOOTING
Safety Fails Take off the left gripframe panel and see if the safety spring (#48) and safety ball (#47) are still in their groove. If they are absent, call PMI immediately.
TRIGGER AND SHOOTING
TROUBLESHOOTING
DO NOT ATTEMPT TO PERFORM MAINTENANCE PROCEDURES UNLESS QUALIFIED TO DO SO.
CONTACT PMI FOR REPAIR ASSISTANCE AND INFORMATION REGARDING AUTHORIZED PMI PIRANHA® REPAIR FACILITIES. PHONE1.800.579.1633 WEB WWW.BUYPMI.COM
BEFORE DISASSEMBLY OF THE MARKER, REMOVE AIR SOURCE; REMOVE ALL PAINTBALLS FROM THE MARKER, BARREL, AND LOADER.TO CHECK IF THE MARKER IS UNLOADED: REMOVE AIR SYSTEM AND SHOOT MARKER IN A SAFE DIRECTION.REMOVE HOPPER, VISUALLY INSPECT CHAMBER FOR A PAINTBALL, REMOVE AND INSPECT BARREL FOR THE PRESENCE OF A PAINTBALL.NEVER LOOK DOWN THE BARREL OF ANY PAINTBALL MARKER ONCE THE BARREL IS SCREWED INTO THE MARKER.
THE PAINTBALL MARKER AIR SYSTEM MUST BE REPAIRED OR REPLACED WITH THE CORRECT PRESSURE RATED COMPONENTS.
SHOOT ONLY QUALITY RPS PAINTBALLS. PMI PREMIUM, EL TIGRE™, ALL STAR®
AND MARBALLIZER® PAINTBALLS ARE RECOMMENDED FOR USE IN THE PMI PIRANHA®
Check barrel O-ring (#39) and firmly tighten barrel.Do not oil barrel O-ring
PAINTBALLS
Check for broken paint or oil in barrel, loader, feedtube and chamber. Bolt/hammer assembly area mustalso be free of broken paint. Check that marker is notshooting over 300 fps. Disassemble and clean
Not flying straight
Check ball detent (#20) and replace if necessary;check that velocity does not exceed 300 fps
Break in Barrel
Does not drop into feed tubeShake loader; check loader and feed tube for broken paint
Two paintballs shoot at a time Check ball detent (#20) and replace if necessary
If it is difficult to tighten the threads onto thereceiver, check to see that the threads on the barrelmatch. If threading is mismatched, barrel is notdesigned for use with PMI Piranha™
Aftermarket barrel does not tighten
BARREL
Barrel comes loose
WWAARRNNIINNGG!�
43 44
Marker shoots but does not recock Check Blue Hammer O-ring for wear and replaceBlue Hammer O-ring (#35) if needed, usingfactory O-ring only. A tank O-ring will not work.Using anything other than a factory Blue HammerO-ring can cause run on. Make sure marker is properly oiled.
Always check for poor quality paintballs prior to playing.Any time paint gets too cold or too warm, there’s always the chance it is ruined.
ORIGINAL SALES PURCHASE RECEIPTOR PACKING SLIPSave your original sales purchase receipt or packing slip. PMI takes pride in manufacturing high quality paintball products that will provide you with many years of trouble free enjoyment. Should you experienceany difficulty in operating or maintaining this PMI Piranha® paintball marker, please re-read the operator’smanual carefully. If further assistance is needed, contact PMI at 1.800.579.1633.
WARRANTY REPAIR RETURN PROCEDUREA returned product must be accompanied by a Return Authorization (RA) number on the outside of the box;please call PMI at 1.800.579.1633 to obtain an RA number before shipping product to PMI. All warrantyreturns must be accompanied by the operator’s name, address, and telephone number. Include operator’s faxand e-mail if possible. Operator must remove all paintballs before shipping, and must pack product securelyto avoid damage during shipping. Include a brief description of what does not appearto work correctly. Ship to: PMI 55 Howard Ave, Des Plaines, Illinois 60018 USA.
OUT OF WARRANTY REPAIRSShould repairs be needed on a PMI Piranha® that is out of warranty, contact PMI at 1.800.579.1633 forinformation regarding authorized PMI Piranha® repair facilities.
Any PMI Piranha® marker returned to PMI for out of warranty repairs must be accompanied by an RA number, description of what does not appear to work correctly, and operator’s information requested in“Warranty Repair Return Procedure” above. Including sales purchase receipt or packing slip is optional for out of warranty repairs. Please note that there will be a minimum labor charge of $20 and there may be additional charges for parts to repair an item/product that is not covered by warranty. An estimate of repaircost will be provided to the customer and authorization to complete the repairs will be obtained prior toadditional repairs being done.
WARRANTY
Pursuit Marketing, Inc. (PMI), extends a warranty to the original purchaser of the PMI Piranha®
paintball marker that the product is free from defects in materials and workmanship for a period of oneyear from the date of purchase. PMI’s obligation under this warranty shall be limited to repairing or replacingany part of the product which is defective.Service for this replacement or repair will be done free of charge upon delivery of the product to PursuitMarketing, Inc. (PMI), 55 Howard Ave, Des Plaines, IL 60018 USA; customer pays shipping charges. Please callPMI at 1.800.579.1633 for information on obtaining warranty service or to obtain a Return Authorization(RA) number before shipping product to PMI. Do not mail your marker in without firstobtaining an RA number. Please make sure to ship your marker through ashipping company that allows you to track and insure your package. PMI isnot responsible for guns that never reach us.
WARRANTY EXCLUSIONS AND LIMITATIONSThis warranty does not apply in the event of misuse or abuse of the product, use of any parts other thanoriginal factory parts, or unauthorized repairs, modifications, or alterations, and does not apply to any partsthat are made defective by modification, misuse, abuse, or accident. This warranty does not apply to O-rings,cup seals, or springs, or to normal fading of anodized finish, scratches, or other cosmetic wear, or to anyitems or parts not manufactured by PMI.
Other than as expressly stated herein, PMI does not make any warranties, express or implied, including butnot limited to implied warranties of merchantability or fitness, for any purpose other than that for which thePMI Piranha® was designed. This warranty gives you specific legal rights. You may have other rights which mayvary from state to state.PMI is not liable for any consequential damages or incidental damages which may arise from the use oroperation of the PMI Piranha® or from any breach of the warranty herein set forth.
WARRANTY REGISTRATION FORMPlease fill out entirely the enclosed PMI Piranha® Warranty Registration form and mail it to: PursuitMarketing, Inc., 55 Howard Ave, Des Plaines, Illinois 60018 USA.
REPAIR PROCEDURE
The PMI Piranha® is a registered trademark. Design rights & all rights reserved. All patterns, drawings,photographs, instructions or manuals remain the intellectual property of the manufacturer. Patents pending. All rights will be strictly enforced.
45 46
PMI Piranha® Paintball Markers manufactured by:
Pursuit Marketing, Inc.55 Howard AveDes Plaines, Illinois 60018 USA Toll Free Phone 1.800.579.1633Phone 847.299.5000www.buypmi.com
Please visitwww.buypmi.com
for updates on your PMI Piranha® Purchase.
Printed in China
WWAARRNNIINNGG!�THE PMI PIRANHA® PAINTBALL MARKER IS NOT A TOY. MISUSE MAY CAUSE SERIOUS INJURY OR DEATH. EYE PROTECTION DESIGNED FOR PAINTBALL USE MUST BE WORN BY THE USER AND ANY PERSON WITHIN RANGE. READ THIS OPERATOR’S MANUAL COMPLETELY BEFORE LOADING, PRESSURIZING, OR OPERATING THE PMI PIRANHA® PAINTBALL MARKER.
#10963
