Page 1418 Annexe - Otto Ganter GmbH & Co. KGPage 1424 | Modification standards s H11 / h11 d max. e...

418 | Annexe

Annexe |

AnnexeModification standards → from Page 1420for modification of standard parts for specific applications

Load rating infomation → from Page 1448

Excerpts from relevant DIN / ISO standards → from Page 1476

Material characteristics → from Page 1483

Surface treatments → from Page 1492

Thread lockings → from Page 1495 for securing and sealing Alphabetical product index → from Page 1498

Numerical product index → from Page 1514

| Technical information

Handwheels Cranked handles Control levers

Positioning of the keyway:

dd

h

bb

t 4t 3

t 2

t 1

DIN 6885 Keyway, key detailsExtract Page 1 heavy type

d b P9 / JS9 Hub keyway

b P9 / N9 Shaft keyway

h t1 = d + t2 t2 t3 = d – t4 t4

6 2 2 2 7 1 +0,1 4,8 1,2 +0,1

7 2 2 2 8 1 +0,1 5,8 1,2 +0,1

8 2 2 2 9 1 +0,1 6,8 1,2 +0,1

9 3 3 3 10,4 1,4 +0,1 7,2 1,8 +0,1

10 3 3 3 11,4 1,4 +0,1 8,2 1,8 +0,1

11 4 4 4 12,8 1,8 +0,1 8,5 2,5 +0,1

12 4 4 4 13,8 1,8 +0,1 9,5 2,5 +0,1

13 5 5 5 15,3 2,3 +0,1 10 3 +0,1

14 5 5 5 16,3 2,3 +0,1 11 3 +0,1

15 5 5 5 17,3 2,3 +0,1 12 3 +0,1

16 5 5 5 18,3 2,3 +0,1 13 3 +0,1

17 5 5 5 19,3 2,3 +0,1 14 3 +0,1

18 6 6 6 20,8 2,8 +0,1 14,5 3,5 +0,1

20 6 6 6 22,8 2,8 +0,1 16,5 3,5 +0,1

22 6 6 6 24,8 2,8 +0,1 18,5 3,5 +0,1

24 8 8 7 27,3 3,3 +0,1 20 4 +0,2

25 8 8 7 28,3 3,3 +0,2 21 4 +0,2

26 8 8 7 29,3 3,3 +0,2 22 4 +0,2

28 8 8 7 31,3 3,3 +0,2 24 4 +0,2

30 8 8 7 33,3 3,3 +0,2 26 4 +0,2

32 10 10 8 35,3 3,3 +0,2 27 5 +0,2

34 10 10 8 37,3 3,3 +0,2 29 5 +0,2

35 10 10 8 38,3 3,3 +0,2 30 5 +0,2

36 10 10 8 39,3 3,3 +0,2 31 5 +0,2

38 10 10 8 41,3 3,3 +0,2 33 5 +0,2

40 12 12 8 43,3 3,3 +0,2 35 5 +0,2

42 12 12 8 45,3 3,3 +0,2 37 5 +0,2

44 12 12 8 47,3 3,3 +0,2 39 5 +0,2

Keyway width

P9 tight fit (standard design) JS9 or N9 loose fit (requires written agreement)

see also... • Keys DIN 6885 → Page 638

|Technical information Page 1421

Control leversCranked handlesHandwheels

Positioning of the keyway:

bb

t 4t 3

h

t 2

t 1 dd

DIN 6885* Keyway, key detailsExtract Page 2 heavy type for machine tools

d b P9 / JS9Hub keyway

b P9 / N9Shaft keyway

h t1 = d + t2 t2 t3 = d – t4 t4

11 4 4 4 12,1 1,1 +0,1 8 3 +0,1

12 4 4 4 13,1 1,1 +0,1 9 3 +0,1

13 5 5 5 14,3 1,3 +0,1 9,2 3,8 +0,1

14 5 5 5 15,3 1,3 +0,1 10,2 3,8 +0,1

15 5 5 5 16,3 1,3 +0,1 11,2 3,8 +0,1

16 5 5 5 17,3 1,3 +0,1 12,2 3,8 +0,1

17 5 5 5 18,3 1,3 +0,1 13,2 3,8 +0,1

18 6 6 6 19,7 1,7 +0,1 13,6 4,4 +0,1

20 6 6 6 21,7 1,7 +0,1 15,6 4,4 +0,1

22 6 6 6 23,7 1,7 +0,1 17,6 4,4 +0,1

24 8 8 7 25,7 1,7 +0,1 18,6 5,4 +0,2

25 8 8 7 26,7 1,7 +0,1 19,6 5,4 +0,2

26 8 8 7 27,7 1,7 +0,2 20,6 5,4 +0,2

28 8 8 7 29,7 1,7 +0,2 22,6 5,4 +0,2

30 8 8 7 31,7 1,7 +0,2 24,6 5,4 +0,2

32 10 10 8 34,1 2,1 +0,2 26 6 +0,2

34 10 10 8 36,1 2,1 +0,2 28 6 +0,2

35 10 10 8 37,1 2,1 +0,2 29 6 +0,2

36 10 10 8 38,1 2,1 +0,2 30 6 +0,2

38 10 10 8 40,1 2,1 +0,2 32 6 +0,2

40 12 12 8 42,1 2,1 +0,2 34 6 +0,2

42 12 12 8 44,1 2,1 +0,2 36 6 +0,2

44 12 12 8 46,1 2,1 +0,2 38 6 +0,2

45 14 14 9 47,6 2,6 +0,2 38,5 6,5 +0,2

46 14 14 9 48,6 2,6 +0,2 39,5 6,5 +0,2

48 14 14 9 50,6 2,6 +0,2 41,5 6,5 +0,2

50 14 14 9 52,6 2,6 +0,2 43,5 6,5 +0,2

Keyway width

P9 tight fit (standard design) JS9 or N9 loose fit (requires written agreement)

see also... • Keys DIN 6885 → Page 638

* This standard has been withdrawn without replacement in 2008-10.

| Modification standards

GN 110 Cross holesfor mounting of operating elements on shafts

d1 H7 / s H11 d2 H11 d3 Length l –0,1 Standard version

Length l –0,1 Handwheels DIN 950 / GN 949 to Ø 250

6 7 2,5 M 3 4,5 – 8 9 3 M 5 5,5 4,510 11 3 M 5 5,5 4,512 13 4 M 6 6,5 5,514 15 4 M 6 6,5 5,516 17 5 M 6 8 718 19 5 M 6 8 720 21 5 M 6 8 722 23 6 M 6 10 924 25 6 M 6 10 926 27 6 M 6 10 9

Information

The connection between the operating element and the shaft consists very often of a cross pin or a grub screw.

As a result the user is faced with relatively high costs since cross holes on operating elements are in general not readily available.

Components with cross holes to GN 110 are not only offered at very competitive prices but they also save the manufacturer unnecessary drawing work. The geometrical form of some of the operating elements, however, does not lend itself to modi-fication to this particular GN standard.

The pin hole d2 H11 is drilled to suit drive spring pins.

1

1

1

1 Type (Cross hole)Handwheels DIN 950-GG-160-B14-A with cross hole GN 110-QE

How to order1

GN 110-QE

|Modification standards Page 1423

GN 110.1 Cross holesfor mounting of universal joint shafts and universal joints on shafts

d1 H7 / s H11 d2 H11 for bore code d3 Length l for bore code

K / V B K / V B

6 - 2 2 M 3 4 4 8 - 3 3 M 5 5,5 5,510 - 3 4 M 5 5,5 612 14 4 5 M 6 6,5 716 18 5 6 M 6 8 920 - 5 8 M 6 8 1022 - 6 8 M 6 10 1025 - 6 10 M 8 10 1430 32 6 12 M 8 14 1635 - 6 12 M 8 16 16

Cross holes in universal joint shafts and in universal shafts are ideal for the production of shaft-hub links using a pin or a thrust screw. For bore holes with a feather key groove or square, they serve to secure the axial position of universal joint and shaft. The d2 pin bore with H11 tolerance is intended for use with coiled spring pins.

The position of the cross holes / the threaded hole with reference to the hub key slot / the square or of the universal joints is shown in the overview.

Should one of the joint sides be delivered without cross holes / threaded holes, this is indicated with QX on the desired location of the article number.

Information

How to order1 2

GN 110.1-QX-GE

1 Shaft side 1

2 Shaft side 2

2 1

21

21

21


s H11 / h11

d max.

e1 max.

e1 min.

e2 min.

4 4,2 5 4,7 5,3 5 5,3 6,5 5,9 6,6 5,5 5,8 7 6,5 7,2 6 6,3 8 7,1 8,1 7 7,3 9 8,3 9,1 8 8,4 10 9,5 10,1 9 9,5 12 10,7 12,110 10,5 13 11,9 13,111 11,6 14 13,1 14,112 12,6 16 14,3 16,113 13,7 17 15,5 17,114 14,7 18 16,7 18,116 16,8 21 19,1 21,217 17,9 22 20,3 22,219 20 25 22,7 25,222 23,1 28 26,3 28,224 25,3 32 28,7 32,227 28,4 36 32,2 36,230 31,7 40 35,8 40,232 33,7 42 38,2 42,236 38 48 43,1 48,241 43,2 54 49,1 54,246 48,5 60 55 60,250 52,7 65 59,8 65,255 57,9 72 65,8 72,2

DIN 79 SquaresExtract for spindles and operating elements

Internal squares may be relieved in the middle third of each square side. The dimension d max. is designed in such way, that this conditions will be met.

The official standard sheet still lists the squares with s = 60, 65, 70, 75 and 80.

Information


GN 109 Level markings / Special lengthsfor oil dipsticks

1 l1 (Length oil dipstick)ATEX-Breather caps GN 552.6-31-G1/2-B-1 with two level markings GN 109-90-80-50

2 l2 (Length 1st notch)

3 l3 (Length 2nd notch)

How to order (with two marking notches)1 2 3

GN 109-90-80-50

Level markings and special lengths GN 109 for oil dipsticks are available for the standards shown above.

The dipstick is shortened to the length l1 and the marking notches are milled in at l2 or l3 with the effect that they are easily visible. The maximum length l1 is given in the appropriate standard. The length specifications l1 to l3 refer to the contact surface without seal, with a tolerance of ±1 mm to be taken into account. For critical applications and depending on stan-dard, the seal must be taken into consideration with a thickness of as much as 2 mm.

If required, more than 2 notches may be cut which are then specified by the appropriate details on the position (l4 ... lx). Also, texts such as MAX / MIN may be laser-engraved in addition to or instead of the notches by submitting the appropriate template.

Information

How to order (with one marking notch) 1 l1 (Length oil dipstick) Breather caps GN 552-42-G3/4-B-1 with one level marking GN 109-110-902 l2 (Length notch)

1 2

GN 109-110-90

1 l1 (Length oil dipstick)Breather caps GN 552-31-M16x1,5-B-2 with oil dipstick in special length GN 109-85

How to order (without marking notch)1

GN 109-85

3

2

1

GN 421 → Page 449 GN 421.10 → Page 450 GN 421.11 → Page 451 GN 421.12 → Page 451

GN 534 → Page 443

GN 5337.2 → Page 407Size 32 ... 74

GN 420 → Page 448

GN 534 → Page 442

GN 5337.2 → Page 406Size 32 ... 74

DIN 464 → Page 457M6 ... M10

GN 5334 → Page 414

DIN 6335 → Page 420 / 422 KT / GG / AL / NI Size 32 ... 63

DIN 466 → Page 456M6 ... M12

GN 5334 → Page 415

GN 6335.4 → Page 423 GN 6335.5 → Page 423Type ST

GN 111.7 Loss protection (Recess with retaining ring)for various standard parts

GN 6336.4* → Page 401 GN 6336.5 → Page 401Type STSize 25 ... 63

DIN 6336* → Page 396 / 398KT / GG / AL / NI Size 25 ... 63

GN 6336.10 → Page 402 GN 6336.11 → Page 403 GN 6336.12 → Page 403

GN 6336.3 → Page 404

* see also GN 6336.13 (with mounted loss protection) → Page 405

Page 1426 | Modification standards

The standards listed can be delivered with loss protection GN 111.7 with a recess and a retaining ring.

The retaining rings are delivered unassembled, as disassembly can lead to their deformation.

Ball chains GN 111 / GN 111.5 resp. retaining cables GN 111. 2 / GN 111.4 are to be ordered separately.

see also...• Star knobs GN 6336.13 (with mounted loss protection) → Page 405

• Ball chains GN 111 → Page 876

• Stainless Steel-Ball chains GN 111.5 → Page 876

• Stainless Steel-Retaining cables GN 111.2 → Page 877

• Spiral retaining cables GN 111.4 → Page 878

Information

Recess for retaining rings and retaining rings GN 111.6 (Stainless Steel) according standard sheet → Page 879

Specification

How to order Knurled thumb screw GN 421-M5-20 with loss protection (recess with retaining ring) GN 111.7

GN 111.7 Loss protection (recess with retaining ring) continued


GN 965 Assembly sets for profile systems 30 / 40for slot width 6 / 8, assembly with T-Nuts GN 506

4 Type

A with cylinder head screw DIN 912

B with countersunk screw DIN 7991

C with lens screw ISO 7380D with cylinder head screw

DIN 7984


GN 965 Assembly sets for profile systems 30 / 40 continued

1 n2 d3 l14 Type

How to order

1 2 3 4

GN 965-8-M6-18-B

Assembly sets GN 965 allow different standard element to be attached to the most common profile systems. Each set includes one T-nut GN 506 and one screw.

GN standards with assembly sets for profile systems → Page 1430 ff.

see also...• T-Nuts GN 506 → Page 872

Information

• T-Nuts GN 506 Steel - zinc plated, blue passivated - Ball / Spring Stainless Steel

• Cylinder head screws DIN 912 Countersunk screws DIN 7991 Lens head screws ISO 7380 Cylinder head screws DIN 7984

Steel zinc plated, blue passivated

• RoHS compliant

Specification

1 2 3

b n d l1 k ≈ l2 l3 s ≈ t ≈Type A Type B Type C Type D Clamping length

30 6 M 4 10 10 - - ... 4 5 12 2,9 8,930 6 M 4 12 - - - 1 ... 6 5 12 2,9 8,930 6 M 4 16 - - - 5 ... 10 5 12 2,9 8,930 6 M 5 10 - - - ... 3 5 12 2,9 8,930 6 M 5 12 12 - - 1 ... 5 5 12 2,9 8,930 6 M 5 14 - - - 3 ... 7 5 12 2,9 8,930 6 M 5 16 - - - 5 ... 9 5 12 2,9 8,930 6 M 5 18 - - - 7 ... 11 5 12 2,9 8,930 6 M 5 22 - - - 11 ... 15 5 12 2,9 8,930 6 M 6 - - - 10 ... 3 5 12 2,9 8,930 6 M 6 12 12 - - 1 ... 4 5 12 2,9 8,930 6 M 6 14 14 14 - 3 ... 6 5 12 2,9 8,930 6 M 6 16 16 - - 5 ... 8 5 12 2,9 8,930 6 M 6 - 18 - - 7 ... 10 5 12 2,9 8,930 6 M 6 20 - - - 9 ... 12 5 12 2,9 8,930 6 M 6 25 - - - 14 ... 17 5 12 2,9 8,940 8 M 4 12 - - - ... 5 7 15 4,6 11,440 8 M 4 14 - - - 1 ... 7 7 15 4,6 11,440 8 M 4 20 - - - 7 ... 13 7 15 4,6 11,440 8 M 5 12 - - - ... 4 7 15 4,6 11,440 8 M 5 14 14 - - 1 ... 6 7 15 4,6 11,440 8 M 5 16 - - - 3 ... 8 7 15 4,6 11,440 8 M 5 18 - - - 5 ... 10 7 15 4,6 11,440 8 M 5 20 - - - 7 ... 12 7 15 4,6 11,440 8 M 5 22 - - - 9 ... 14 7 15 4,6 11,440 8 M 5 25 - - - 12 ... 17 7 15 4,6 11,440 8 M 6 14 14 - 14 1 ... 5 7 15 4,6 11,440 8 M 6 16 16 16 - 3 ... 7 7 15 4,6 11,440 8 M 6 18 18 - - 5 ... 9 7 15 4,6 11,440 8 M 6 - 20 - - 7 ... 11 7 15 4,6 11,440 8 M 6 22 - 22 - 9 ... 13 7 15 4,6 11,440 8 M 6 28 - - - 15 ... 19 7 15 4,6 11,440 8 M 8 14 - - - 1 ... 4 7 15 4,6 11,440 8 M 8 16 16 16 - 3 ... 6 7 15 4,6 11,440 8 M 8 18 - 18 - 5 ... 8 7 15 4,6 11,440 8 M 8 20 - - - 7 ... 10 7 15 4,6 11,440 8 M 8 28 - - - 15 ... 18 7 15 4,6 11,4


Hinges GN 127 → Page 980

GN 127-...-B - GN 965-8-M6-20-B

Mounting plate GN 139.3 (for hinges with / without safety switch GN 139.1 / GN 139.2) → Page 994

GN 139.3-170 GN 965-6-M6-12-A GN 965-8-M6-14-A


GN 139.4-101 GN 965-6-M6-12-A GN 965-8-M6-14-A

Flanged connector clamps GN 145 → Page 1195

GN 145-... - GN 965-8-M5-16-A

Hinges GN 151.4 → Page 981

GN 151.4-... - GN 965-8-M6-18-A


GN 159-54-17,5-17,5GN 159-74-22,5-22,5

GN 965-6-M6-16-B-

-GN 965-8-M6-18-B

Double hinges GN 159.1 → Page 970

GN 159.1-89-35-35GN 159.1-119-45-45

GN 965-6-M6-16-B-

-GN 965-8-M6-18-B

Assembly sets GN 965

Compatible GN standardsin ascending order of the standard numbers




GN 161-57 / 68 / 80 - GN 965-8-M6-16-B

Base plate connector clamps GN 162.3 → Page 1201

GN 162.3-... GN 965-6-M5-16-A GN 965-8-M5-18-A

Fastening sets GN 181 (for cabinet „U“ handles) → Page 116

GN 181-ZD-8-M4-...GN 181-ZD-10-M5-...GN 181-ZD-...-M6-...GN 181-ZD-...-M8-...

GN 965-6-M4-10-BGN 965-6-M5-12-BGN 965-6-M6-12-B

-

-GN 965-8-M5-14-BGN 965-8-M6-14-BGN 965-8-M8-16-B

Tube supports GN 231 → Page 1216

GN 231-B20 / B25 / B30GN 231-V20 / V25 / V30

--

GN 965-8-M8-14-AGN 965-8-M8-14-A

Hinge GN 239.3 → Page 1002

GN 239.3-70-60-SH - GN 965-8-M6-18-B

Hinges with safety switch GN 239.4 → Page 1002

GN 239.4-... - GN 965-8-M6-18-B


GN 239.6-60-110-... - GN 965-8-M6-18-B




|Modification standards 31


GN 239.7-60-70GN 239.7-60-110

- GN 965-8-M6-18-B

Mounting plates GN 239.8 (for hinges GN 239.6 / GN 239.7) → Page 1000

GN 239.8-110-14-...GN 239.8-110-19-...

GN 965-6-M6-16-B-

-GN 965-8-M6-18-B

Swivel clamp connector bases GN 271 → Page 1220

GN 271-25-... - GN 965-8-M5-18-A

Sensor holders GN 271.4 → Page 1239

GN 271.4-B12-... GN 271.4-B18-...

- GN 965-8-M5-18-A

Swivel clamp connector joints GN 281 → Page 1230

GN 281-... - GN 965-8-M5-18-A

Tubular handles GN 333 → Page 136

GN 333-28-...-B-... GN 965-6-M6-25-A GN 965-8-M6-28-A







Tubular handles GN 333.1 → Page 130

GN 333.1-28-...-B-... GN 965-6-M6-14-C GN 965-8-M6-16-C

Oval tubular handles GN 334.1 → Page 143

GN 334.1-36-... - GN 965-8-M8-16-C

Indexing plungers GN 412 → Page 672

GN 412-5-35-...-1GN 412-6-35-...-1GN 412-8-47-...-1GN 412-10-47-...-1

GN 965-6-M4-16-AGN 965-6-M4-16-A GN 965-6-M5-18-AGN 965-6-M5-18-A

--

GN 965-8-M5-20-AGN 965-8-M5-20-A

Mounting blocks GN 412.1 → Page 698

GN 412.1-35-...-1GN 412.1-47-...-1

GN 965-6-M4-16-AGN 965-6-M5-18-A

-GN 965-8-M5-20-A

Spring latches GN 416 → Page 675

GN 416-6-38-...GN 416-8-38-...GN 416-8-46-...GN 416-10-38-...GN 416-10-46-...GN 416-12-46-...

GN 965-6-M5-14-AGN 965-6-M5-14-A

-GN 965-6-M5-14-A

--

GN 965-8-M5-16-AGN 965-8-M5-16-AGN 965-8-M6-16-AGN 965-8-M5-16-AGN 965-8-M6-16-AGN 965-8-M6-16-A





Locators GN 416.1→ Page 676

GN 416.1-6-38GN 416.1-8-38GN 416.1-8-46GN 416.1-10-38GN 416.1-10-46GN 416.1-12-46

GN 965-6-M5-14-AGN 965-6-M5-14-A

-GN 965-6-M5-14-A

--



GN 417-5-A / -B / -CGN 417-6-A / -B / -CGN 417-8-A / -BGN 417-8-CGN 417-10-A / -B / -C

GN 965-6-M4-12-AGN 965-6-M5-14-AGN 965-6-M5-14-A

--

-GN 965-8-M5-16-AGN 965-8-M5-16-AGN 965-8-M5-16-AGN 965-8-M6-16-A


GN 417.1-5GN 417.1-6GN 417.1-8GN 417.1-10

GN 965-6-M4-12-AGN 965-6-M5-14-AGN 965-6-M5-14-A

-

-GN 965-8-M5-16-AGN 965-8-M5-16-AGN 965-8-M6-16-A

Base clamp mountings GN 473 → Page 1246

GN 473-B8-...GN 473-B10 / B12-...GN 473-B15 / B16-...GN 473-B20-...

GN 965-6-M4-10-A---

GN 965-8-M4-14-AGN 965-8-M5-12-AGN 965-8-M6-14-AGN 965-8-M6-18-A

Clamp mountings GN 477 → Page 1247

GN 477-B8-... GN 477-B10 / B12-... GN 477-B15 / B16 / B20-...

GN 965-6-M4-16-A GN 965-6-M5-18-A GN 965-6-M6-20-A

GN 965-8-M4-20-A GN 965-8-M5-20-A GN 965-8-M6-22-A





Flanged bolts GN 480 → Page 1253

GN 480-8-...GN 480-10 / 12-...GN 480-15 / 16 / 20-...

GN 965-6-M4-10-AGN 965-6-M5-10-AGN 965-6-M6-12-A

GN 965-8-M4-12-AGN 965-8-M5-12-AGN 965-8-M6-14-A

Cabinet U-Handles GN 528 → Page 90

GN 528-...-94-6,5-...GN 528-...-117-6,5-..GN 528-...-117-8,5-...GN 528-...-132-8,5-...GN 528-...-140-8,5-...GN 528-...-160-8,5-...GN 528-...-179-8,5-...

GN 965-6-M6-14-AGN 965-6-M6-16-A

-----

GN 965-8-M6-16-AGN 965-8-M6-16-AGN 965-8-M8-18-AGN 965-8-M8-18-AGN 965-8-M8-18-AGN 965-8-M8-20-AGN 965-8-M8-20-A

Cabinet U-Handles GN 565.1 → Page 81

GN 565.1-20-...GN 565.1-26-...

GN 965-6-M5-22-A-

-GN 965-8-M6-22-A

Inclined cabinet U-Handles GN 565.2 → Page 86

GN 565.2-26-128-B-...GN 565.2-26-160-B-...

--

GN 965-8-M6-22-CGN 965-8-M6-22-C

Cam action indexing plungers GN 612.2 → Page 710

GN 612.2-...-16-...GN 612.2-...-20-...

GN 965-6-M5-18-AGN 965-6-M5-22-A

GN 965-8-M5-22-AGN 965-8-M5-25-A






GN 612.9-...-16-...GN 612.9-...-20-...

GN 965-6-M5-18-AGN 965-6-M5-22-A

GN 965-8-M5-20-AGN 965-8-M5-25-A


GN 628-...-117-6,5-B-...GN 628-...-117-8,5-B-...GN 628-...-150-8,5-B-...GN 628-...-179-8,5-B-...

GN 965-6-M6-16-A---

-GN 965-8-M8-28-AGN 965-8-M8-28-AGN 965-8-M8-28-A

Ledge handles GN 630 → Page 161

GN 630-114-B-... GN 965-6-M6-18-B GN 965-8-M6-22-C


GN 630.1-114-B-... GN 965-6-M6-18-B GN 965-8-M6-22-C

Panel support clamp GN 649 → Page 1274

GN 649-35-E GN 965-6-M6-10-D GN 965-8-M6-14-D


GN 667-20-... - GN 965-8-M8-20-A





Spring latches GN 722.3 → Page 712

GN 722.3-8-...GN 722.3-10-...GN 722.3-12-...GN 722.3-14-...

----



GN 728-120-B-...GN 728-180-B-...

GN 965-6-M6-14-A-

-GN 965-8-M8-18-A


GN 728.5-120-B-... GN 965-6-M6-14-A -

Angle pieces / Shackles GN 967 → Page 1272

GN 967-...-20-...-1-...GN 967-...-20-...-2-...GN 967-...-30-...-1-...GN 967-...-30-...-2-...GN 967-...-40-...-1-...GN 967-...-40-...-2-...GN 967-...-45-...-1-...GN 967-...-45-...-2-...

GN 965-6-M5-12-AGN 965-6-M5-12-BGN 965-6-M6-12-AGN 965-6-M6-12-B

----

GN 965-8-M5-14-AGN 965-8-M5-14-BGN 965-8-M6-14-AGN 965-8-M6-14-BGN 965-8-M8-16-AGN 965-8-M8-16-BGN 965-8-M8-16-AGN 965-8-M8-16-B

Threaded flanges GN 3490 → Page 1273

GN 3490-45-...GN 3490-60-...

GN 965-6-M6-14-B-

-GN 965-8-M8-16-B



Ball-shaped door locks GN 4490 → Page XYZ

GN 4490-ZD-50...GN 4490-ZD-68...GN 4490-ZD-80...

GN 965-6-M4-10-BGN 965-6-M4-10-BGN 965-6-M5-14-B

GN 965-8-M4-12-BGN 965-8-M4-12-BGN 965-8-M5-14-B






GN 968 Assembly sets for profile systems 30 / 40 / 45for slot width 8 / 10, assembly with T-Nuts GN 505

4 Type

A with cylinder head screw DIN 912

B with countersunk screw DIN 7991

C with lens screw ISO 7380D with cylinder head screw

DIN 7984


1 n2 d3 l14 Type

How to order

1 2 3 4

GN 968-8-M5-18-A

1 2 3

b n d l1 k ≈ l2 ±0,5 s ≈ t ≈Type A Type B Type C Type D Clamping

length

30 8 M 4 10 - - - ... 6 16 2,2 7,230 8 M 4 12 - - - 2 ... 8 16 2,2 7,2 30 8 M 4 16 - - - 6 ... 12 16 2,2 7,2 30 8 M 5 10 - - - ... 5 16 2,2 7,2 30 8 M 5 12 12 - - 2 ... 7 16 2,2 7,2 30 8 M 5 14 - - - 4 ... 9 16 2,2 7,2 30 8 M 5 18 - - - 8 ... 13 16 2,2 7,2 30 8 M 5 20 - - - 10 ... 15 16 2,2 7,2 30 8 M 5 22 - - - 12 ... 17 16 2,2 7,2 30 8 M 6 10 - - 10 ... 4 16 2,2 7,2 30 8 M 6 12 12 - - 2 ... 6 16 2,2 7,2 30 8 M 6 14 14 14 - 4 ... 8 16 2,2 7,2 30 8 M 6 16 16 - - 6 ... 10 16 2,2 7,2 30 8 M 6 - 18 - - 8 ... 12 16 2,2 7,230 8 M 6 20 - - - 10 ... 14 16 2,2 7,230 8 M 6 25 - - - 15 ... 19 16 2,2 7,240 / 45 10 M 4 14 - - - ... 8 19 6 11,840 / 45 10 M 5 12 - - - ... 5 19 6 11,840 / 45 10 M 5 14 14 - - ... 7 19 6 11,840 / 45 10 M 5 16 - - - 3 ... 9 19 6 11,840 / 45 10 M 5 18 - - - 5 ... 11 19 6 11,840 / 45 10 M 5 20 - - - 7 ... 13 19 6 11,840 / 45 10 M 5 25 - - - 12 ... 18 19 6 11,840 / 45 10 M 6 14 14 - 14 ... 6 19 6 11,840 / 45 10 M 6 16 - - - 3 ... 8 19 6 11,840 / 45 10 M 6 18 18 18 - 5 ... 10 19 6 11,840 / 45 10 M 6 20 20 - - 7 ... 12 19 6 11,840 / 45 10 M 6 22 22 22 - 9 ... 14 19 6 11,840 / 45 10 M 6 28 - - - 15 ... 20 19 6 11,840 / 45 10 M 8 14 - - - ... 5 19 6 11,840 / 45 10 M 8 16 16 16 - 3 ... 7 19 6 11,840 / 45 10 M 8 18 - 18 - 5 ... 9 19 6 11,840 / 45 10 M 8 20 - - - 7 ... 11 19 6 11,840 / 45 10 M 8 28 - - - 15 ... 19 19 6 11,8

GN 968 Assembly sets for profile systems 30 / 40 / 45 continued

Assembly sets GN 968 allow different standard element to be attached to the most common profile systems. Each set includes one T-nut GN 505 and one screw.

GN standards with assembly sets for profile systems → Page 1440 ff.

see also...• T-Nuts GN 505 → Page 878

Information

• T-Nut GN 505 with increased torque (Type MB) Steel zinc plated , blue passivated

• Cylinder head screws DIN 912 Countersunk screws DIN 7991 Socket button head screws ISO 7380 Cylinder head screws DIN 7984

Steel zinc plated, blue passivated

• RoHS compliant

Specification

1) only for profile 40 x 40 2) only for profile 45 x 45




GN 127-...-B - GN 968-10-M6-20-B 1)


GN 139.3-170 GN 968-8-M6-10-A GN 968-10-M6-14-A


GN 139.4-101 GN 968-8-M6-10-A GN 968-10-M6-14-A

Flanged connector clamps GN 145 → Page 1195

GN 145-... - GN 968-10-M5-18-A


GN 151.4-...-B - GN 968-10-M6-18-A 1)


GN 159-54-17,5-17,5GN 159-74-22,5-22,5GN 159-84-25-25

GN 968-8-M6-16-B--

-GN 968-10-M6-18-B 1)GN 968-10-M6-18-B 2)



1) only for profile 40 x 40



Double hinges GN 159.1 → Page 970

GN 159.1-89-35-35GN 159.1-119-45-45GN 159.1-134-50-50

GN 968-8-M6-16-B--

-GN 968-10-M6-18-B 1)GN 968-10-M6-18-B 2)


GN 161-57 / 68 / 80 GN 968-8-M6-14-B GN 968-10-M6-18-B

Base plate connector clamps GN 162.3 → Page 1201

GN 162.3-... GN 968-8-M5-14-A GN 968-10-M5-18-A

Fastening sets GN 181 (for cabinet „U“ handles) → Page 116

GN 181-ZD-10-M5-...GN 181-ZD-... -M6-...GN 181-ZD-... -M8-...

GN 968-8-M5-12-BGN 968-8-M6-12-B

-

-GN 968-10-M6-16-BGN 968-10-M8-16-B

Tube supports GN 231 → Page 1216

GN 231-B20 / B25 / B30GN 231-V20 / V25 / V30

--

GN 968-10-M8-14-A

GN 968-10-M8-14-A

Hinge GN 239.3 → Page 1002

GN 239.3-70-60-SH - GN 968-10-M6-18-B 1)




GN 239.4-... - GN 968-10-M6-18-B 1)


GN 239.6-60-110-... - GN 968-10-M6-18-B 1)


GN 239.7-60-70 GN 239.7-60-110

- GN 968-10-M6-18-B 1)

Mounting plates GN 239.8 (for hinges GN 239.6 / GN 239.7) → Page 1000

GN 239.8-110-14-...GN 239.8-110-19-...GN 239.8-110-21-...

GN 968-8-M6-14-B--

-GN 968-10-M6-18-B GN 968-10-M6-18-B

Swivel clamp connector bases GN 271 → Page 1220

GN 271-25-... - GN 968-10-M5-18-A

Sensor holders GN 271.4 → Page 1239

GN 271.4-B12-... GN 271.4-B18-...

-

-GN 968-10-M5-18-A







Swivel clamp connector joints GN 281 → Page 1230

GN 281-... - GN 968-10-M5-18-A

Tubular handles GN 333 → Page 136

GN 333-28-...-B-... GN 968-8-M6-25-A GN 968-10-M6-28-A

Tubular handles GN 333.1 → Page 130

GN 333.1-28-...-B-... GN 968-8-M6-14-C GN 968-10-M6-18-C

Oval tubular handles GN 334.1 → Page 143

GN 334.1-36-... - GN 968-10-M8-16-C


GN 412-8-47-...-1GN 412-10-47-...-1

GN 968-6-M5-18-AGN 968-6-M5-18-A

GN 968-8-M5-20-AGN 968-8-M5-20-A

Mounting blocks GN 412.1 → Page 698

GN 412.1-47-...-1 GN 968-8-M5-18-A -



Spring latches GN 416 → Page 416

GN 416-6-38GN 416-8-38GN 416-8-46GN 416-10-38GN 416-10-46GN 416-12-46

GN 968-8-M5-14-AGN 968-8-M5-14-A

-GN 968-8-M5-14-A

--


Locators GN 416.1 → Page 676

GN 416.1-6-38GN 416.1-8-38GN 416.1-8-46GN 416.1-10-38GN 416.1-10-46GN 416.1-12-46

GN 968-8-M5-14-AGN 968-8-M5-14-A

-GN 968-8-M5-14-A

- -



GN 417-5-A / -B / -CGN 417-6-A / -B / -CGN 417-8-A / -BGN 417-8-CGN 417-10-A / -B / -C

GN 968-8-M4-12-AGN 968-8-M5-14-AGN 968-8-M5-14-A

--

-GN 968-10-M5-18-AGN 968-10-M6-18-AGN 968-10-M5-18-AGN 968-10-M6-18-A


GN 417.1-5GN 417.1-6GN 417.1-8GN 417.1-10

GN 968-8-M4-12-AGN 968-8-M5-14-AGN 968-8-M5-14-A

-

-GN 968-10-M5-18-AGN 968-10-M5-18-AGN 968-10-M6-18-A

Base clamp mountings GN 473 → Page 1246

GN 473-B8-...GN 473-B10 / B12-...GN 473-B15 / B16-...GN 473-B20-...

GN 968-8-M4-10-A---








Clamp mountings GN 477 → Page 1247

GN 477-B8-...GN 477-B10 / B12-...GN 477-B15 / B16 / B20-...

GN 968-8-M4-16-AGN 968-8-M5-18-AGN 968-8-M6-20-A

-GN 968-10-M5-20-AGN 968-10-M6-22-A

Flange bolts GN 480 → Page 1253

GN 480-8-...GN 480-10 / 12-...GN 480-15 / 16 / 20-...

GN 968-8-M4-10-AGN 968-8-M5-10-AGN 968-8-M6-12-A

-GN 968-10-M5-12-AGN 968-10-M6-14-A


GN 528-...-94-6,5-...GN 528-...-117-6,5-...GN 528-...-117-8,5-...GN 528-...-122-8,5-...GN 528-...-132-8,5-...GN 528-...-140-8,5-...GN 528-...-160-8,5-...GN 528-...-179-8,5-...GN 528-...-235-8,5-...

GN 968-8-M6-14-AGN 968-8-M6-16-A

-------

GN 968-10-M6-16-AGN 968-10-M6-20-AGN 968-10-M8-16-AGN 968-10-M8-16-AGN 968-10-M8-18-AGN 968-10-M8-18-AGN 968-10-M8-20-AGN 968-10-M8-20-AGN 968-10-M8-20-A


GN 565.1-20-...GN 565.1-26-...

GN 968-8-M5-20-A-

-GN 968-10-M6-22-A

Inclined cabinet U-Handles GN 565.2 → Page 86

GN 565.2-26-128-B-...GN 565.2-26-160-B-...

--

GN 968-10-M6-22-CGN 968-10-M6-22-C






GN 612.2-...-16-...GN 612.2-...-20-...

GN 968-8-M5-18-AGN 968-8-M5-22-A

-GN 968-10-M5-25-A


GN 612.9-...-16-...GN 612.9-...-20-...

GN 968-8-M5-18-AGN 968-8-M5-22-A

-GN 968-10-M5-25-A


GN 628-...-117-6,5-B-...GN 628-...-117-8,5-B-...GN 628-...-150-8,5-B-...GN 628-...-179-8,5-B-...

GN 968-8-M6-14-A---

-GN 968-10-M8-28-AGN 968-10-M8-28-AGN 968-10-M8-28-A

Ledge handles GN 630 → Page 161

GN 630-114-B-... GN 968-8-M6-18-B GN 968-10-M6-22-B


GN 630.1-114-B-... GN 968-8-M6-18-B GN 968-10-M6-22-B

Panel support clamp GN 649 → Page 1274

GN 649-35-E GN 968-8-M6-10-D GN 968-10-M6-14-D


GN 667-20-... - GN 968-10-M8-20-A







GN 722.3-8-...GN 722.3-10-...GN 722.3-12-...GN 722.3-14-...

----



GN 728-120-B-...GN 728-180-B-...

GN 968-8-M6-14-A-

-GN 968-10-M8-18-A


GN 728.5-120-B-... GN 965-6-M6-14-A -

Angle pieces / Shackles GN 967 → Page 1272

GN 967-...-20-...-1-...GN 967-...-20-...-2-...GN 967-...-30-...-1-...GN 967-...-30-...-2-...GN 967-...-40-...-1-...GN 967-...-40-...-2-...GN 967-...-45-...-1-...GN 967-...-45-...-2-...

GN 968-8-M5-12-AGN 968-8-M5-12-BGN 968-8-M6-12-AGN 968-8-M6-12-B

----

GN 968-10-M5-14-AGN 968-10-M5-14-BGN 968-10-M6-14-AGN 968-10-M6-14-BGN 968-10-M8-16-AGN 968-10-M8-16-BGN 968-10-M8-16-AGN 968-10-M8-16-B

Threaded flanges GN 3490 → Page 1273

GN 3490-45-...GN 3490-60-...

GN 968-8-M6-14-B-

GN 968-10-M8-16-BGN 968-10-M8-16-B

Ball-shaped door locks GN 4490 → Page XYZ

GN 4490-ZD-50...GN 4490-ZD-68...GN 4490-ZD-80...

GN 968-6-M4-10-BGN 968-6-M4-10-BGN 968-6-M5-14-B

GN 968-8-M4-12-BGN 968-8-M4-12-BGN 968-8-M5-14-B


|Load rating information Page 1449

Extensive test series were carried out in order to obtain strength details of the plastic cabinet "U" handles listed below. The results provide informa-tion on the impact strength and the tensile strength under normal stress loads in two stress load directions.

The impact strength S1 and S2 was determined using the outline drawing shown opposite:

A cylindrical steel element rounded at the tip (weight 0.680 kg) repeatedly hits the handle, with the height of drop increased by 0.1 mm with every drop. Failure occurs at the specified S values.

The details given on strength are non-binding guide values without any liability. In general, they do not constitute a warranty of quality. The user must determine from case to case if a product is suitable for the envisa-ged use.

Strength properties of cabinet "U" handles in plasticsorted by ascending standard numbers

Cabinet "U" handles GN 528-PA → Page 90Größe 94 117 122 132 140 160 179 235S1 in J 15 20 25 27 27 29 20 40S2 in J 8 13 14 14 20 20 20 34K1 in N 3500 4500 3700 3500 3400 3300 2800 3200K2 in N 2500 2500 2500 2500 2600 2700 2700 3500

Cabinet "U" handles GN 528-PP → Page 90Größe 94 117 122 132 140 160 179 235S1 in J 8 10 12 12 13 15 16 17S2 in J 3 4 5 5 6 7 8 11K1 in N 1700 2000 1600 2000 1800 1800 1800 1700K2 in N 1300 1500 1500 1300 1300 1300 1300 1700

Cabinet "U" handles GN 528-SV → Page 90Größe 94 117 132 179S1 in J 9 10 12 20S2 in J 5 8 8 13K1 in N 1750 3500 3000 1400K2 in N 1700 2200 1800 2100

Cabinet "U" handles GN 528-ESD → Page 90Größe 94 117S1 in J 15 20S2 in J 8 13K1 in N 3500 4500K2 in N 2500 2500

Cabinet "U" handles GN 528.1-PP → Page 91Größe 117S1 in J 9S2 in J 4K1 in N 1900K2 in N 950

Cabinet "U" handles GN 528.1-PA → Page 91Größe 94 105 117 132 179 - M8 179 - M10S1 in J 10 10 12 18 24 24S2 in J 6 7 9 16 30 30K1 in N 2000 2000 3000 2000 3000 3200K2 in N 1800 1800 1600 1800 2300 2500

h Impact strength S1 = P x h1

hImpact strength S2 = P x h2

KBreaking load K2

KBreaking load K2

| Load rating information

Strength properties of cabinet "U" handles in plastic continued

Cabinet "U" handles GN 528.4 → Page 91Größe 117 179S1 in J 11 24S2 in J 9 30K1 in N 2200 3400K2 in N 1400 2600

Cabinet "U" handles GN 625 → Page 89Größe 86 117 179 300 S1 in J 50 50 27 25S2 in J 120 120 80 75K1 in N 4000 4000 3000 2000K2 in N 7000 5000 3500 3000

Cabinet "U" handles GN 628 → Page 96Größe 94 117 132 150 179S1 in J 8 10 11 12 16S2 in J 3 4 4 5 9K1 in N 2000 2700 2700 2700 2200K2 in N 1500 1800 1800 1500 1500

Cabinet "U" handles GN 630.1 → Page 88Größe 114S1 in J –S2 in J –K1 in N 90K2 in N –

Ledge handles GN 630 → Page 161Größe 114S1 in J –S2 in J –K1 in N 90K2 in N –

Cabinet "U" handles GN 725 → Page 84Größe 86 94 117 120 132 150 179 235 300S1 in J 12 10 8 8 8 8 11 11 18S2 in J 6 8 12 12 12 13 13 13 11K1 in N 2400 2300 2250 2250 2200 2000 1900 1900 2000K2 in N 2400 2300 2650 2650 2450 2550 2000 2000 2000

Cabinet "U" handles GN 725.1 → Page 85Größe 86 117 132 179S1 in J 11 11 11 11S2 in J 9 9 9 13K1 in N 3000 2000 1900 1900K2 in N 2200 2800 1900 1900

|Load ratings Page 1451

Load rating of cabinet "U" handles/tubular handles in metalin ascending order of the standard numbers

An extensive series of tests were carried out with the cabinet "U" handles / tubular handles listed below.

The handles were slowly loaded and relieved at room temperature with incrementally increasing force. After load relieve, a deTypeation irrelevant in terms of function and appearance remained at the listed values for F1

and F2 respectively. The breaking loads were in most cases multiples above the specified value.

Note: The details given on load rating are non-binding guide values without any liability. In general, they do not constitute a warranty of quality.

The user must determine from case to case if a product is suitable for the envisaged use. Ambient factors and ageing may influence the specified values.

Tubular handles GN 333 → Page 136Size 20-200 20-250 20-300 20-350 20-400F1 1700 1500 1200 800 500F2 2800 2500 2000 1500 500Size 28-200 28-250 28-300 28-350 28-400 28-500 28-600F1 2500 2250 2000 1750 1650 1575 1500F2 4750 4250 3750 3250 2750 2250 1500Size 30-200 30-300 30-350 30-400 30-500 30-600 30-1000F1 2500 2250 2200 2200 2000 1800 750F2 3500 3400 3200 2850 2250 1900 800

Tubular handles GN 333.1 → Page 130Size 20-180 20-200 20-250 20-300 20-350 20-400F1 1600 1500 1400 1250 750 700F2 2500 2000 1900 1600 1550 1250Size 28-200 28-250 28-300 28-350 28-400 28-500 28-600F1 1700 1500 1500 1350 1000 1000 1000F2 4800 3500 2800 2400 1800 1700 1500Size 30-200 30-300 30-350 30-400 30-500 30-600 30-1000F1 3000 2400 2400 2350 2350 1750 1250F2 4000 3700 3000 2700 2300 2000 1000

Tubular handles GN 331 → Page 132Size 30-200 30-300F1 3000 2400F2 4000 3700

Tubular handles GN 332 → Page 138Size 30-200 30-300F1 2500 2250F2 3500 3400

Load capacity F1 in N

Load capacity F2 in N

Cabinet "U" handles GN 225 → Page 97Size 18 20 22 25F1 2250 2250 3000 3500F2 5500 7500 9750 9750

| Load ratings

Stainless Steel-Arch handles GN 424.5 → Page 120Size 64 96 128 160 192F1 1500 900 900 800 600F2 7500 5750 3000 2250 1750

Stainless Steel-Tubular handles GN 333.5 → Page 134Size 200 250 300 400 500 600F1 3000 2500 2000 1750 1500 1450F2 7500 6000 5000 4250 3500 2500

Arch handles GN 424.1 → Page 120Size 64 96 128 160 192F1 1300 800 800 700 525F2 6500 5250 2700 2000 1550

Tubular handles GN 333.3 → Page 131Size 242 292 392 492 592F1 1800 1700 1650 1600 1500F2 3500 3000 2500 2000 1500

Oval tubular handles GN 334 → Page 142Size 200 250 300 350 400 500 600 800F1 1750 1650 1500 1500 1250 1200 1100 700F2 3000 2400 1750 1750 1500 1350 1000 700

Oval tubular handles GN 366 → Page 152Size 200 250 300 400 500 600F1 2000 2000 2000 1500 1300 900F2 3500 2800 2250 1600 1450 1150

Oval tubular handles GN 334.1 → Page 143Size 200 250 300 350 400 500 600 800F1 1700 1650 1500 1450 1400 1200 1000 750F2 3000 2700 2500 2000 1500 1250 1000 750

Tubular handles GN 333.2 → Page 137Size 242 292 392 492 592F1 2400 2200 2000 1900 1600F2 3700 3200 2400 2200 1650

Cabinet "U" handles GN 423 - Type A → Page 98Size 55 88 100 120 180 235F1 270 250 220 200 180 150F2 1700 1500 1000 600 500 250

Cabinet "U" handles GN 423 - Type B → Page 98Size 55 88 100 120 180 235F1 270 250 220 200 180 150F2 1600 1250 800 400 300 200

Load rating of cabinet "U" handles / tubular handles in metal continued- F1 / F2 → Page 1450


Cabinet "U" handles, Steel GN 425 → Page 102Size 8-55 8-64 8-88 8-96 8-100 8-120 8-128F1 475 550 500 500 500 450 500F2 5000 4300 3300 3000 2800 1750 1250Size 10-88 10-100 10-120 10-180 10-200 10-235F1 1300 900 900 700 500 400F2 4000 3750 3000 2000 1200 1150Size 12-125 12-160 12-200 12-250F1 1200 1000 400 200F2 6000 4000 3000 3400Size 16-160 16-200 16-250 16-300F1 1900 1300 1100 800F2 5000 4000 3500 5750

Stainless Steel-Cabinet "U" handles GN 425 → Page 103Size 8-55 8-64 8-88 8-96 8-100 8-120 8-128F1 600 850 700 700 700 700F2 4000 3000 2500 2000 1500 1300Size 10-88 10-100 10-120 10-180 10-200 10-235F1 1400 1000 1000 700 600 500F2 4000 3800 3000 2250 1500 1400Size 12-125 12-160 12-200 12-250F1 1200 1000 700 500F2 7000 4500 3000 2500Size 16-160 16-200 16-250 16-300F1 1900 1300 1100 800F2 8500 7000 5000 4000

Cabinet "U" handles, Aluminum GN 425 → Page 103Size 8-55 8-64 8-88 8-96 8-100 8-120 8-128F1 300 300 300 200 200 200 200F2 1400 1200 825 750 700 575 450Size 10-88 10-100 10-120 10-180 10-200 10-235F1 500 450 400 350 250 250F2 2000 1500 1000 700 600 500Size 12-125 12-160 12-200 12-250F1 400 300 250 200F2 2000 1000 800 800Size 16-160 16-200 16-250 16-300F1 800 750 500 250F2 2300 2000 1500 1000

Cabinet "U" handles, Steel GN 425.1 → Page 106Size 8-55 8-64 8-88 8-96 8-100F1 500 425 450 375 325F2 700 600 500 600 400Size 10-88 10-100 10-120 10-180 10-200F1 1000 900 900 500 500F2 2000 1500 1500 750 700


| Load ratings

Cabinet "U" handles, Steel GN 425.1 → Page 106Size 12-125 12-160 12-200 12-250F1 1150 1250 1425 875F2 1925 1500 1425 1250

Folding handles, Steel GN 425.2 → Page 122Size 100 120 180F1 1750 1600 1250F2 2600 2600 2500

Stainless Steel-Folding handles GN 425.2 → Page 122Size 100 120 180F1 2000 2000 1750F2 5000 3500 2250

Folding handles, Steel GN 425.5 → Page 123Size 100 120 180F1 500 500 500F2 – – –

Stainless Steel-Folding handles GN 425.5 → Page 123Size 100 120 180F1 500 500 500F2 – – –

Cabinet "U" handles, Aluminum GN 425.1 → Page 107Size 8-55 8-64 8-88 8-96 8-100F1 400 350 300 250 250F2 400 400 350 350 350Size 10-88 10-100 10-120 10-180 10-200F1 400 450 400 350 250F2 500 500 500 450 400Size 12-125 12-160 12-200 12-250F1 600 600 500 650F2 725 1050 1000 900

Stainless Steel-Cabinet "U" handles GN 425.1 → Page 107Size 8-55 8-64 8-88 8-96 8-100F1 450 500 500 500 500F2 500 1000 1000 1000 1000Size 10-88 10-100 10-120 10-180 10-200F1 1500 1450 1450 500 500F2 2150 2000 2000 1000 1000Size 12-125 12-160 12-200 12-250F1 700 1250 1350 1350F2 1650 1700 2250 1750



Stainless Steel-Cabinet "U" handles GN 427.5 → Page 100Size 55 88 100 120 180 200 235F1 2400 2100 2000 1800 1250 850 800F2 6000 5000 3750 3000 1700 1500 1200

Cabinet "U" handles GN 427 → Page 100Size 55 88 100 120 180 200 235F1 650 600 500 450 300 250 200F2 1600 1150 1100 1000 550 500 400

Stainless Steel-Cabinet "U" handles GN 426.6 - Type A → Page 115Size 20-200 20-300 28-250 28-350 28-500F1 4200 4000 2000 1500 2700F2 7500 7000 5000 3500 2250

Stainless Steel-Cabinet "U" handles GN 426.6 - Type B → Page 115Size 20-250 20-300 28-250 28-350 28-500F1 1000 500 1000 1250 1750F2 1200 1200 1250 1750 1750

Stainless Steel-Cabinet "U" handles GN 426.5 - Type B → Page 109Size 20-200 20-250 20-300 20-350 28-250 28-300 28-350 28-400F1 1000 1600 1400 1400 2700 2700 2700 2700F2 4000 9000 6500 7500 10000 7000 6000 5000

Folding handles with recessed tray GN 425.8 → Page 124Size 100 120F1 1000 1000F2 5000 5000

Cabinet "U" handles GN 426 → Page 108Size 20-200 20-250 20-300 20-350 28-250 28-300 28-350 28-400F1 1400 1100 1100 1000 2000 1900 1800 1500F2 3300 3000 2300 2200 4500 3500 3500 3500

Cabinet "U" handles GN 426.1 → Page 114Size 20-200 20-300 28-250 28-350 28-500F1 1500 1450 3000 2500 2300F2 1600 1400 2000 2000 2000

Stainless Steel-Cabinet "U" handles GN 426.5 - Type A → Page 109Size 20-200 20-250 20-300 20-350 28-250 28-300 28-350 28-400F1 4000 6000 5500 3500 4000 3500 2800 2750F2 9000 10000 8000 6500 8000 7250 6750 6500


| Load ratings

Cabinet "U" handles GN 565 → Page 80Size 20-100 20-112 20-117 20-120 20-128 20-160 20-180 20-200F1 1250 1250 1250 1250 1250 1200 1250 1250F2 2100 2200 2200 2200 2200 2000 1750 2000Size 20-235F1 1000F2 1250Size 26-112 26-117 26-120 26-125 26-128 26-160 26-179 26-192F1 3000 2900 2900 2800 2800 2800 2400 2300F2 7000 6000 5500 5000 4500 3500 3250 3000Size 26-300 26-400 26-500F1 1700 1600 1200F2 2250 1750 1500

Cabinet "U" handles GN 565.1 → Page 81Size 20-100 20-112 20-120 20-128 20-160F1 1000 1200 1500 1000 1100F2 2500 2400 3250 2300 2000

Cabinet "U" handles GN 564 → Page 83Size 112 128 160F1 900 900 900F2 1200 1200 1200

Cabinet "U" handle GN 559 - Type B / Type C → Page 94Size 162F1 1000F2 2500

Cabinet "U" handle GN 559 - Type A → Page 94Size 162F1 5000F2 8000

Cabinet "U" handles GN 428 - Type A → Page 117Size 28-250 28-300 28-400F1 1250 2250 1500

F2 4250 2750 2200Size 36-300 36-400 36-500 36-600 36-800F1 5750 6250 3750 2500 1750F2 7500 6750 5750 4000 1000

Cabinet "U" handles GN 428 - Type B → Page 117Size 28-250 28-300 28-400F1 1500 1250 1250

F2 3500 2750 1750Size 36-300 36-400 36-500 36-600 36-800F1 4500 7000 3750 2250 1750F2 7500 6500 4500 3500 1000



Stainless Steel-Arch handles GN 565.9 → Page 118Size 20-160 20-192F1 4500 2500F2 4500 2500

Stainless Steel-Cabinet "U" handles GN 565.5 - Type A → Page 82Size 20-112 20-128 20-160 20-200 20-250 20-300 20-350 20-400F1 4000 3200 3100 3000 2800 2500 2000 1500F2 7000 6000 4000 3800 3000 3000 2300 1500

Stainless Steel-Cabinet "U" handles GN 565.5 - Type B → Page 82Size 20-112 20-128 20-160F1 3000 2000 2500F2 6850 5800 4250

Stainless Steel-Cabinet "U" handles GN 565.7 → Page 87Size 20-112 20-128F1 5250 5000F2 7250 3500

Cabinet "U" handles GN 565.3 → Page 93Size 20-120 20-160F1 1400 1500F2 1900 2750

Arch handles GN 565.4 → Page 118Size 20-160 20-192 26-160 26-192F1 1300 1000 2000 2000F2 3500 2500 5000 5000

Arch handles GN 665 → Page 119Size 26-350 26-450F1 1200 1100F2 2700 1550

Inclined cabinet "U" handles GN 565.2 - Type B → Page 86Size 26-128 26-160F1 1750 1500F2 1850 2500

Inclined cabinet "U" handles GN 565.2 - Type A → Page 86Size 20-112 20-128 26-128 26-160F1 1900 1900 2400 2000F2 2400 2000 5200 4800

Cabinet "U" handles GN 565.1 → Page 81Size 26-116 26-120 26-132 26-164 26-179 26-196F1 2000 3000 2000 2000 1800 1750F2 5000 6250 4000 3600 3400 3000


| Load ratings

Tubular arch handles GN 666.4 (Tube, Aluminum) → Page 148Size 400 500 600F1 750 750 750F2 1800 1700 1500

Tubular arch handles GN 666.4 (Tube, Stainless Steel) → Page 148Size 400 500 600F1 1350 1700 1750F2 5000 4500 3750

Tubular handles GN 666.1 (Tube, Stainless Steel) → Page 147Size 200 250 300 350 400 500 600F1 1150 1150 1200 1200 1150 1100 1000F2 3000 3000 2750 2500 2000 1850 1350

Tubular handles GN 666.1 (Tube, Aluminum) → Page 147Size 200 250 300 350 400 500 600F1 1000 1350 1500 1500 1750 1750 1500F2 5500 5500 5250 4500 4500 3500 2500


Cabinet "U" handles GN 667 (Tube, Aluminum) → Page 140Size 20-180 20-200 20-250 20-300 20-350 20-400F1 750 750 600 600 550 500F2 2000 2000 2000 1500 1250 1000Size 30-300 30-350 30-400 30-500 30-600 30-700 30-1000F1 1100 1100 750 750 750 625 550F2 3000 2250 2250 1750 1500 1250 1000


Tubular handles GN 666 (Tube, Aluminum) → Page 146Size 200 250 300 350 400 500 600F1 900 850 950 1000 1000 1100 1000F2 2500 2450 2400 2300 1750 1700 1350

Tubular handles GN 666 (Tube, Stainless Steel) → Page 146Size 200 250 300 350 400 500 600F1 900 850 950 1000 1000 1100 1000F2 2500 2450 2400 2300 1750 1700 1350



Cabinet "U" handles GN 728.5 → Page 92Size 120F1 2500F2 5000

Cabinet "U" handles GN 728 → Page 92Size 120 180F1 2000 2500F2 2500 2750

System handles GN 669 → Page 144Size 200 250 300 400 500 600F1 1750 1500 1250 1200 1000 900F2 3000 2250 2100 2000 1500 1000

Flat cabinet "U" handles GN 668 - Type B → Page 95Size 20-130 20-70 20-190 20-210F1 700 650 600 550F2 2400 2000 1600 1200

Flat cabinet "U" handles GN 668 - Type A → Page 95Size 20-130 20-170 20-190 20-210F1 1600 1600 1500 1350F2 2100 1900 1800 1650

Cabinet "U" handles GN 667 (Tube, Stainless Steel) → Page 140Size 20-180 20-200 20-250 20-300 20-350 20-400F1 1200 1100 1000 1000 750 700F2 4000 3500 3500 2500 2000 1000Size 30-300 30-350 30-400 30-500 30-600 30-700 30-1000F1 1250 1250 1200 1200 1200 900 800F2 5000 5000 4250 4000 2250 2000 1000


| Load ratings

Load rating of metal hingesin ascending order of the standard numbers

An extensive series of tests were carried out with the hinges listed below.

The hinges were slowly loaded and relieved at room temperature with incrementally increasing force. After load relieve, a deformation irrelevant in terms of function and appearance remained at the listed values for LA, LR0 and LR90. The breaking loads were in most cases multiples above the specified value.

The details given on load rating are non-binding guide values without any liability. In general, they do not constitute a warranty of quality.

The user must determine from case to case if a product is suitable for the envisaged use. Ambient factors and ageing may influence the specified values.

Article No. Radial load rating Axial load ratingLR0 in N LR90 in N LA in N

GN 127 -76-60 2000 2000 1150 GN 136 -30-30-ST - - - -30-45-ST - - - -40-40-ST 1000 700 2000 -40-60-ST - - - -50-50-ST 2000 1000 2500 -50-75-ST - - - -60-60-ST 2500 1200 2800 -60-90-ST - - - -30-30-NI - - - -30-45-NI - - - -40-40-NI 1000 700 2000 -40-60-NI - - - -50-50-NI 2000 1000 2500 -50-75-NI - - - -60-60-NI 2500 1100 2800 -60-90-NI - - -GN 138 -ZD-40-42-A 1500 4000 1000 -ZD-50-52-A 3500 6000 1750 -ZD-60-62-A 4000 6500 2000GN 139.1 -49-101 1000 1000 1500 -79-101 500 500 750

GN 139.2 -49-101 1000 1000 1500 -79-101 500 500 750GN 139.5 -76-126 2000 2000 2000GN 139.6 -76-126 2000 2000 2000 GN 161 -57 1150 1500 600 -68 1500 1200 750 -80 2500 2500 1000 GN 237 -AL-30-30-A-EL 1200 750 550 -AL-40-40-A-EL 2000 2800 1060


Load rating of metal hinges continued - LR0 / LR90 / LA → Page 1459

Article No. Radial load rating Axial load ratingLR0 in N LR90 in N LA in N

GN 237 -AL-50-50-A-EL 3000 4250 2250 -AL-60-60-A-EL 5000 5150 4050 -NI-30-30-A-GS 1700 750 750 -NI-40-40-A-GS 4000 1650 2100 -NI-50-50-A-GS 6500 2250 2550 -NI-60-60-A-GS 10000 5000 5000 -A4-30-30-A-GS 1700 750 750 -A4-40-40-A-GS 4000 1650 2100 -A4-50-50-A-GS 6500 2250 2550 -A4-60-60-A-GS 10000 5000 5000 -ZD-30-30-A 1200 750 500 -ZD-40-40-A 2100 2000 1150 -ZD-50-50-A 3500 2450 2100 -ZD-60-60-A 6000 4400 3200 -ZD- 40-40-C 1700 1850 900 -ZD- 50-50-C 3550 2000 2050 -ZD- 60-60-C 4050 2550 3050 GN 237 -NI- 63-50-A-GS 4000 2000 1500 -NI- 76-50-A-GS 4000 2000 1200 -NI- 90-60-A-GS 4500 2000 1500 -NI-120-60-A-GS 4500 2000 1200 -ZD- 63-50-A 3000 1250 1500 -ZD- 76-50-A 3000 1250 1300 -ZD- 90-60-A 4500 1500 1500 -ZD-120-60-A 4500 1500 1300

-ZD- 63-50-C 3000 2000 1500

-ZD- 76-50-C 3000 2000 1200 -ZD- 90-60-C 4500 1500 2000 -ZD-120-60-C 4500 1500 1500 GN 238 -42-42-BJ 1500 2100 1050 -42-42-EJ 1000 1500 1200 -42-42-NJ 1250 1350 1500 -50-50-BJ 1500 2200 1500 -50-50-EJ 1500 1700 1500 -50-50-NJ 1800 1900 2000 -60-60-BJ 2500 3200 1500 -60-60-EJ 2000 2000 1500 -60-60-NJ 3700 2600 2550 GN 337 -NI-40-40-A-GS 3000 3500 2000 -NI-50-50-A-GS 5000 3500 2500 -NI-60-60-A-GS 6000 6000 5000 -ZD-40-40-A 2200 1600 1500 -ZD-50-50-A 3000 2500 2500 -ZD-60-60-A 4300 3500 3100 GN 437 -ZD-40-40-A 2400 1600 1200 -ZD-50-50-A 3200 2000 1600 -ZD-60-60-A 4500 2500 2000

| Load ratings

Article No. Radial load rating Axial load rating Max. tightening torque of the hinge attachment in Nm

LR0 in N LR90 in N LA in N

Bore Thread Bolt

GN 151 -39-40-A 240 (2220) 100 (730) 200 (2050) – 5 – -39-40-B 230 (1760) 180 (1330) 137 (1800) 1 – – -39-40-C 290 (2030) 280 (1520) 130 (2080) 1 – – -48-49-A 440 (3070) 170 (1470) 400 (3770) – 5 – -48-49-B 310 (2530) 250 (1620) 360 (3080) 2 – – -48-49-C 310 (2880) 320 (2490) 300 (2960) 2 – – -48-49-D 360 (1970) 200 (1680) 370 (3070) – – 5 -48-49-E 320 (1970) 200 (1620) 360 (3070) 2 – 5 -48-49-F 280 (1970) 200 (1680) 370 (2960) 2 – 5 -48-49-G 360 (1970) 200 (1470) 370 (3070) – 5 5 -48-49-H 320 (2530) 170 (1470) 360 (3080) 2 5 – -48-49-I 280 (2880) 170 (1470) 400 (2960) 2 5 – -64-65-A 690 (5670) 220 (2280) 640 (4570) – 5 – -64-65-B 490 (5790) 260 (3190) 510 (5280) 5 – – -64-65-C 720 (6270) 240 (4180) 520 (4760) 3 – – -64-65-D 460 (6620) 220 (3190) 510 (5890) – – 5 -64-65-E 460 (5790) 220 (3190) 510 (5280) 3 – 5 -64-65-F 460 (6270) 220 (3190) 510 (4760) 5 – 5 -64-65-G 460 (5670) 220 (2280) 510 (4570) – 5 5 -64-65-H 460 (5670) 220 (2280) 510 (4570) 5 5 – -64-65-I 690 (5670) 220 (2280) 640 (4570) 3 5 – -98-98-A 2120 (17940) 590 (5210) 970 (7660) – 5 – -98-98-B 2060 (13670) 540 (4760) 1050 (4860) 5 – – -98-98-C 1230 (10460) 510 (4100) 1110 (6730) 5 – – -98-98-D 1730 (16190) 460 (3690) 890 (5950) – – 5 -98-98-E 1730 (13670) 460 (3690) 890 (4860) 5 – 5 -98-98-F 1230 (10460) 460 (3690) 890 (5950) 5 – 5 -98-98-G 1730 (16190) 460 (3690) 890 (5950) – 5 5 -98-98-H 2060 (13670) 540 (4760) 970 (4860) 5 5 – -98-98-I 1230 (10460) 510 (4110) 970 (6730) 5 5 –

The values given in (...) are the breaking loads determined in a series of tests. They are designed to estimate the safety factor.

When attaching the different hinges, a maximum tightening torque must not be exceeded.

The details given on load rating are non-binding guide values without any liability. In general, they do not constitute a warranty of quality. The user must determine from case to case if a product is suitable for the intended purpose.

Load rating of plastic hingesin ascending order of the standard numbers


Article No. Radial load rating Axial load rating Max. tightening torque of the hinge attachment in Nm

LR0 in N LR90 in N LA in N

Bore Thread Bolt

GN 151.4-64-65 490 (5790) 260 (3190) 519 (5280) 3 – –GN 159 -54-17,5-17,5 1850 (3710) 300 (1700) 440 (2570) 5 – – -64-17,5-22,5 1750 (3490) 590 (870) 320 (2280) 5 – – -69-17,5-25 1760 (3520) 190 (780) 240 (2150) 5 – – -84-17,5-32,5 1600 (3190) 180 (850) 280 (1510) 5 – – -74-22,5-22,5 1750 (3490) 220 (870) 320 (2280) 5 – – -79-22,5-25 1750 (3490) 390 (780) 240 (2150) 5 – – -94-22,5-32,5 1600 (3190) 180 (850) 280 (1510) 5 – – -84-25-25 1760 (3520) 190 (780) 240 (2150) 5 – – -99-25-32,5 1600 (3190) 180 (780) 240 (1510) 5 – – -114-32,5-32,5 1600 (3190) 180 (850) 280 (1510) 5 – – -80-102-8,5 4500 (10000) 2000 (4000) 2000 (4000) 5 – –GN 159.1-89-35-35 1850 (3710) 300 (1700) 440 (2570) 5 – – -109-40-40 1750 (3490) 220 (870) 320 (2280) 5 – – -99-40-40 1750 (3490) 220 (870) 320 (2280) 5 – – -119-45-45 1750 (3490) 220 (870) 320 (2280) 5 – – -104-42,5-42,5 1760 (3520) 190 (780) 240 (2150) 5 – – -124-47,5-47,5 1750 (3490) 190 (780) 240 (2150) 5 – – -134-50-50 1760 (3520) 190 (780) 240 (2150) 5 – – -119-50-50 1600 (3190) 180 (850) 280 (1510) 5 – – -139-55-55 1600 (3190) 180 (850) 280 (1510) 5 – – -149-57,5-57,5 1600 (3190) 180 (780) 240 (1510) 5 – –GN 233 -37-43 1400 (1800) 500 (1000) 700 (1100) 1 – – -57-64 2250 (3200) 1500 (2500) 1500 (2350) 3 – – GN 237.1-30-30-A 1700 1000 1400 3 – – -30-30-B 1700 850 1300 3 – – -40-40-A 1900 1280 1900 3 – – -40-40-B 1600 1000 1900 5 – – -40-40-C 1900 1000 2000 – – 5 -40-40-D 1900 1000 1900 3 – 5 -40-40-E 1600 1000 1900 5 – 5 -50-50-A 2400 1720 2630 5 – – -50-50-B 2410 1360 2860 5 – – -50-50-C 2560 2100 2340 – – 5 -50-50-D 2400 1720 2340 5 – 5 -50-50-E 2410 1360 2340 5 – 5 -60-60-A 2960 3070 3320 5 – – -60-60-B 2810 2170 3440 5 – – -60-60-C 3940 2130 3000 – – 5 -60-60-D 2960 2130 3000 5 – 5 -60-60-E 2810 2130 3000 5 – 5

Load rating of plastic hinges continued

| Information for loads

Computing the strength of indexing plungersfor shear loads / flexure loads of the plunger pin

Provided that a miniscule gap remains between the guide of the indexing plunger and the indexing bore hole opposite, the load can be reduced to a clean shear action.

As this is normally not the case, the “flexure” load case should preferably be considered on the following page.

Approximately 80 % of the bolt’s tensile strength is assumed for the shear strength. This approach calculates against the tensile strength Rm, i.e. against the indexing pin shearing off. Any pre-existing and re-maining deformation may, however, mean that the indexing plunger can be used no longer. To ensure the permanent and proper function of the indexing plunger, the yield limit Re must be considered in place of the tensile strength Rm.

Shear loads

On principle, the design also needs an adequate safety coefficient to be taken into account. The usual safety coefficients under static load 1,2 to 1,5; pulsating 1,8 to 2,4 and alternating 3 to 4.

Disclaimer:

Our information and recommendations are given with non-binding effect and ruling out any liability, unless we have expressly committed ourselves in writing to provide information and recommendations. All products are standard elements for versatile uses and as such are subject to extensive standard tests. You should carry out your own test se-ries to verify whether a certain product is suitable for your specific applications. We cannot be held responsible for this.

Safety information

The tensile strength shown in the table opposite (Rm) and the yield or substitute yield limit (Re / Rp 0,2) have been determine in tension tests involving tension specimen in accordance with DIN 50125- B6-30

These tests constitute the basis for the load bearing details given herein.

Material characteristics

d Bolt diameter

max. force F in N, acc. to material and strength value differsC45Pb / 1.0504 X 10 CrNiS 18 9 / 1.4305at Re at Rm at Re at Rm

3 3160 3610 3270 4180 4 5620 6430 5830 7430 5 8790 10050 9110 11620 6 12660 14470 13120 16730 8 22510 25730 23320 2975010 35180 40210 36440 4649012 50660 57900 52470 6695016 90070 102940 93290 119020

Computing examples, load values

Example:

Indexing plungers with a bolt diameter of 6 mm made of Stainless Steel with a yield limit of Re = 580 N/mm², com-putation against permanent deformation, the maximum per-missible shear stress is wanted.

Fper = (6 mm)² x π x 0,8 x 580 N/mm² = 13120 N 4

Formulas for computation

Bolt cross-section Limit tension Shear force

S = d² x π 4

τa = 0,8 x Rm F = S x τa = d² x π x 0,8 x Rm 4

Material Re Rm

Description Material no. in N/mm² in N/mm²

C45Pb 1.0504 560 640

X 10 CrNiS 18 9 AISI 303 580 740

|Information for loads Page 1465

As soon as a gap I remains between the guide and the indexing bore hole opposite, the load can be reduced to a flexure rod clamped in at one side.

With this approach, the computation is made against the bending of the indexing plunger as a case of failure.

Flexure loads

Formulas for computation

Resistance torque Flexural stress Flexural strength

W = π x d³ 32

Mb = σb x W F = Mb = σb x π x d³ l l x 32

d Bolt diameter

max. flexural strength F in N, acc. to material and gap l differentiatedC45Pb / 1.0504 X 10 CrNiS 18 9 / 1.4305l = 2 mm l = 3 mm l = 2 mm l = 3 mm

3 740 490 760 510 4 1750 1170 1820 1210 5 3430 2290 3550 2370 6 5930 3950 6140 4100 8 14070 9380 14570 971010 27480 18320 28470 1898012 47490 31660 49190 3279016 90070 102940 93290 119020

Computing examples, load values

Example:

Indexing plungers with a bolt diameter of 5 mm made of steel with a yield limit of Re = 560 N/mm², computation against permanent deformation, the maximum permissible flexural strength is wanted:

Fper = 560 N/mm² x π x (5mm)³ = 3430 N 2mm x 32

The yield or substitute yield limit (Re / Rp 0,2) shown in the table opposite has been determine in tension tests involving tension specimen in accordance with DIN 50125- B6-30.

These tests constitute the basis for the load bearing details given herein.

Material characteristics

On principle, the design also needs an adequate safety coefficient to be taken into account. The usual safety coefficients under static load 1,2 to 1,5; pulsating 1,8 to 2,4 and alternating 3 to 4.

Disclaimer:

Our information and recommendations are given with non-binding effect and ruling out any liability, unless we have expressly committed ourselves in writing to provide information and recommendations. All products are standard elements for versatile uses and as such are subject to extensive standard tests. You should carry out your own test series to verify whether a certain product is suitable for your specific applications. We cannot be held responsible for this.

Safety information

Computing the strength of indexing plungers / cam action plungers continued

Material Re

Description Material no. in N/mm²(≈ per. flexural tension σb)

C45Pb 1.0504 560

X 10 CrNiS 18 9 AISI 303 580

Resilent characteristics for rubber buffers GN 351 / GN 451

d1 h Spring rate ≈ in N/mm

max. load in N

max. travel in mm

Spring rate ≈ in N/mm

max. load in N

max. travel in mm


max. load in N

max. travel in mm

8 8 25 50 2 25 50 2 25 50 2 8 13 13 43 3,25 12 38 3,25 10 32 3,25 10 10 28 56 2 30 75 2,5 30 75 2,5 10 15 17 65 3,75 17 65 3,75 17 65 3,75 10 20 15 73 5 12 59 5 11 57 5 15 10 83 195 2 84 210 2,5 84 210 2,5 15 15 41 155 3,75 41 155 3,75 41 155 3,75 15 20 30 150 5 30 150 5 30 150 5 15 25 - - - 21 130 6,25 20 125 6,25 20 15 120 175 1,5 86 320 3,75 86 320 3,75 20 20 44 220 5 44 220 5 44 220 5 20 25 42 265 6,25 42 265 6,25 42 265 6,25 20 30 - - - 38 285 7,5 38 285 7,5 25 15 - - - 230 860 3,75 230 860 3,75 25 20 78 390 5 78 390 5 80 390 5 25 25 71 440 6,25 - - - - - - 25 30 58 430 7,5 58 430 7,5 60 430 7,5 30 15 - - - 260 985 3,75 265 985 3,75 30 20 1100 770 0,7 - - - - - - 30 30 67 500 7,5 65 500 7,5 65 500 7,5 30 40 63 630 10 65 630 10 65 630 10 40 20 1040 2400 2,25 360 1800 5 360 1800 5 40 30 150 1140 7,5 150 1140 7,5 150 1140 7,5 40 40 106 1050 10 105 1060 10 105 1060 10 50 20 - - - 605 3030 5 605 3030 5 50 30 270 2010 7,5 270 2010 7,5 270 2010 7,5 50 40 150 1480 10 150 1480 10 150 1480 10 50 50 120 1500 12,5 120 1500 12,5 120 1500 12,5 60 30 400 3020 7,5 405 3020 7,5 405 3020 7,5 60 40 250 2520 10 250 2520 10 250 2520 10 60 50 200 2740 13,75 210 2890 13,75 190 2620 13,75 70 30 3200 11200 3,5 860 6020 7 860 6000 7 70 45 340 3810 11,25 340 3810 11,25 340 3810 11,25 75 25 - - - 1760 11000 6,25 1760 11000 6,25 75 30 2940 9700 3,25 - - - - - - 75 40 490 4910 10 490 4910 10 490 4910 10 75 55 250 3470 13,75 250 3470 13,75 250 3470 13,75100 40 1310 10500 8 1400 13990 10 1400 13990 10100 55 530 7320 13,75 530 7320 13,75 530 7320 13,75100 75 415 7790 18,75 415 7790 18,75 415 7790 18,75125 55 1320 18200 13,75 1250 17500 13,75 1250 17250 13,75125 75 710 13300 18,75 650 12700 18,75 650 12200 18,75

GN 351 / GN 451 Resilient characte-ristics for 40° Shore under axial and static load.

Type EE Type ES Type SS

Page 1466 | Load ratings

Resilent characterics for rubber buffers GN 351 / GN 451 continued


max. load in N

max. travel in mm


max. load in N

max. travel in mm


max. load in N

max. travel in mm

8 8 43 85 2 43 85 2 43 85 2 8 13 23 75 3,25 21 69 3,25 19 63 3,25 10 10 35 70 2 40 100 2,5 40 100 2,5 10 15 27 100 3,75 27 100 3,75 27 100 3,75 10 20 22 110 5 20 99 5 18 93 5 15 10 155 315 2 130 325 2,5 130 325 2,5 15 15 75 280 3,75 75 280 3,75 75 280 3,75 15 20 47 235 5 47 235 5 47 235 5 15 25 - - - 37 235 6,25 37 235 6,25 20 15 150 230 1,5 130 480 3,75 130 480 3,75 20 20 86 430 5 85 430 5 86 430 5 20 25 69 435 6,25 69 435 6,25 69 435 6,25 20 30 - - - 56 420 7,5 56 415 7,5 25 15 - - - 285 1070 3,75 285 1070 3,75 25 20 125 620 5 125 620 5 125 620 5 25 25 85 530 6,25 - - - - - - 25 30 70 525 7,5 70 525 7,5 70 525 7,5 30 15 - - - 555 2080 7,5 555 2080 7,5 30 20 1520 1060 0,7 - - - - - - 30 30 140 1055 7,5 140 1055 7,5 140 1050 7,5 30 40 93 930 10 95 930 10 93 930 10 40 20 530 2650 5 485 2430 5 485 2430 5 40 30 210 1575 7,5 210 1570 7,5 210 1570 7,5 40 40 140 1400 10 140 1400 10 140 1400 10 50 20 - - - 820 4100 5 820 4100 5 50 30 440 3300 7,5 440 3300 7,5 440 3300 7,5 50 40 215 2130 10 215 2130 10 215 2130 10 50 50 175 2190 12,5 175 2190 12,5 175 2190 12,5 60 30 555 4170 7,5 555 4170 7,5 555 4170 7,5 60 40 360 3610 10 360 3610 10 360 3610 10 60 50 275 3410 12,5 275 3410 12,5 275 3410 12,5 70 30 1225 4900 4 1140 8570 7,5 1140 8570 7,5 70 45 635 7130 11,25 635 7130 11,25 635 7130 11,25 75 25 - - - 2075 12970 6,25 2075 12970 6,25 75 30 3190 9895 3 - - - - - - 75 40 700 6970 10 700 6970 10 700 6970 10 75 55 545 7510 13,75 545 7510 13,75 545 7510 13,75100 40 1925 15400 8 2000 20000 10 2000 20000 10 100 55 950 13080 13,75 950 13080 13,75 950 13080 13,75 100 75 515 9640 18,75 515 9640 18,75 515 9640 18,75 125 55 1400 19260 13,75 1400 19260 13,75 1400 19260 13,75125 75 1035 19440 18,75 1035 19440 18,75 1035 19440 18,75






max. load in N

max. travel in mm


max. load in N

max. travel in mm


max. load in N

max. travel in mm

8 8 75 150 2 75 150 2 75 150 2 8 13 47 150 3,25 45 145 3,25 41 130 3,25 10 10 83 165 2 80 200 2,5 80 200 2,5 10 15 40 150 3,75 40 150 3,75 40 56 1,4 10 20 20 100 5 19 96 5 18 88 5 15 10 290 580 2 290 715 2,5 290 715 2,5 15 15 135 515 3,75 140 515 3,75 140 515 3,75 15 20 94 470 5 94 470 5 94 470 5 15 25 - - - 81 505 6,25 80 500 6,25 20 15 365 550 1,5 280 1040 3,75 280 1040 3,75 20 20 200 955 5 200 955 5 200 955 5 20 25 160 1010 6,25 160 1010 6,25 160 1010 6,25 20 30 - - - 160 1210 7,5 130 980 7,5 25 15 - - - 715 2690 3,75 715 2690 3,75 25 20 305 1535 5 305 1530 5 305 1530 5 25 25 220 1370 6,25 - - - - - - 25 30 160 1210 7,5 160 1210 7,5 160 1210 7,5 30 15 - - - 880 3300 3,75 880 3300 3,75 30 20 3230 2260 0,7 - - - - - - 30 30 260 1960 7,5 260 490 2 260 490 2 30 40 200 2000 10 200 2000 10 200 2000 10 40 20 2820 6200 2,25 890 4450 5 890 4450 5 40 30 455 3420 7,5 455 3420 7,5 455 3420 7,5 40 40 320 3190 10 320 3190 10 320 3190 10 50 20 - - - 1850 9240 5 1850 9240 5 50 30 725 5450 7,5 725 5450 7,5 725 5450 7,5 50 40 495 4940 10 495 4940 10 495 4940 10 50 50 420 4750 11,25 380 4750 12,5 380 4750 12,5 60 30 1220 9130 7,5 1215 9130 7,5 1215 9130 7,5 60 40 695 6950 10 695 6950 10 695 6950 10 60 50 715 7125 10 525 6570 12,5 525 6570 12,5 70 30 2420 7250 3 3380 24010 7 3380 24010 7 70 45 1170 13210 11,25 1170 13210 11,25 1170 13210 11,25 75 25 - - - 4000 25000 6,25 4000 25000 6,25 75 30 5000 25000 5 - - - - - - 75 40 1540 15380 10 1540 15380 10 1540 15380 10 75 55 817 11240 13,75 815 11240 13,75 815 11240 13,75100 40 2900 29000 10 2900 29000 10 2900 29000 10100 55 1760 24260 13,75 1760 24260 13,75 1760 24260 13,75100 75 1190 22350 18,75 1190 22350 18,75 1190 22350 18,75125 55 3185 25000 7,85 3010 23610 7,85 3010 23610 7,75125 75 1270 23750 18,75 1290 24200 18,75 1160 21790 18,75




GN 352 / GN 452

Resilient characteristics for 40° Shore under axial and static load.

Resilent characteristics for rubber buffers GN 352 / GN 452


max. load in N

max. travel in mm


max. load in N

max. travel in mm

8 8 17 33 2 17 33 2 8 13 - - - - - - 10 10 21 53 2,5 21 53 2,5 10 15 18 69 3,75 18 69 3,75 10 20 - - - 11 54 5 15 10 - - - 55 110 2 15 15 38 140 3,75 38 140 3,75 15 20 27 135 5 27 135 5 15 30 17 125 7,5 17 125 7,5 20 10 155 390 2,5 155 390 2,5 20 15 77 290 3,75 77 290 3,75 20 20 52 260 5 52 260 5 20 25 43 270 6,25 - - - 20 30 32 235 7,5 32 235 7,5 25 15 130 485 3,75 130 485 3,75 25 20 83 415 5 83 415 5 25 30 39 290 7,5 39 290 7,5 30 15 200 745 3,75 200 745 3,75 30 20 115 565 5 115 565 5 30 25 92 575 6,25 92 575 6,25 30 30 80 600 7,5 80 600 7,5 30 40 55 550 10 - - - 40 20 240 1200 5 240 1200 5 40 25 190 1170 6,25 190 1170 6,25 40 30 150 1140 7,5 150 1140 7,5 40 40 100 995 10 100 995 10 50 20 535 2680 5 535 2680 5 50 30 255 1820 7,5 245 1820 7,5 50 40 245 1430 10 145 1430 10 50 50 110 1370 12,5 110 1370 12,5 60 20 375 1880 5 375 1880 5 60 30 430 3220 7,5 430 3220 7,5 60 40 260 2600 10 260 2600 10 60 50 180 2240 12,5 180 2240 12,5 60 60 170 2530 15 170 2530 15 70 30 655 4930 7,5 655 4930 7,5 70 40 385 3850 10 385 3850 10 70 55 240 3320 13,75 240 3320 13,75 75 25 1050 6560 6,25 1050 6560 6,25 75 30 805 6000 7,5 1160 5800 5 75 40 500 5010 10 500 5010 10 75 50 320 3970 12,5 320 3970 12,5100 40 945 9430 10 945 9430 10100 50 665 8320 12,5 665 8320 12,5100 60 495 7440 15 495 7440 15125 55 1543 21220 13,75 1430 19700 13,75125 75 1000 18720 18,75 940 17600 18,75

Type E Type S



GN 352 / GN 452



max. load in N

max. travel in mm


max. load in N

max. travel in mm

8 8 28 55 2 28 55 2 8 13 16 51 3,25 16 51 3,25 10 10 35 88 2,5 35 88 2,5 10 15 25 92 3,75 25 92 3,75 10 20 - - - 19 95 5 15 10 - - - 84 170 2 15 15 69 260 3,75 69 260 3,75 15 20 45 225 5 45 225 5 15 30 34 260 7,5 34 260 7,5 20 10 260 645 2,5 260 645 2,5 20 15 125 470 3,75 125 470 3,75 20 20 73 365 5 73 365 5 20 25 63 395 6,25 - - - 20 30 56 420 7,5 56 420 7,5 25 15 215 795 3,75 215 795 3,75 25 20 115 580 5 115 580 5 25 30 79 590 7,5 79 590 7,5 30 15 275 1020 3,75 275 1020 3,75 30 20 205 1010 5 205 1010 5 30 25 165 1030 6,25 165 1030 6,25 30 30 105 780 7,5 105 780 7,5 30 40 78 780 10 - - - 40 20 500 2500 5 500 2500 5 40 25 265 1660 6,25 265 1660 6,25 40 30 195 1480 7,5 195 1480 7,5 40 40 140 1400 10 140 1400 10 50 20 690 3460 5 690 3460 5 50 30 335 2520 7,5 335 2520 7,5 50 40 275 2760 10 275 2760 10 50 50 215 2700 12,5 215 2700 12,5 60 20 770 3850 5 770 3850 5 60 30 715 5370 7,5 715 5370 7,5 60 40 355 3540 10 355 3540 10 60 50 265 3300 12,5 265 3300 12,5 60 60 230 3480 15 230 3480 15 70 30 955 7170 7,5 955 7170 7,5 70 40 630 6280 10 630 6280 10 70 55 420 5770 13,75 420 5770 13,75 75 25 1550 9660 6,25 1550 9660 6,25 75 30 1050 7890 7,5 1050 7890 7,5 75 40 670 6680 10 670 6680 10 75 50 445 5570 12,5 445 5570 12,5 100 40 1210 12110 10 1210 12110 10 100 50 1120 14040 12,5 1120 14040 12,5 100 60 865 12950 15 865 12950 15 125 55 1810 23790 13,25 1810 23790 13,25125 75 1070 20120 18,75 1070 20120 18,75

Type E Type S



GN 352 / GN 452



max. load in N

max. travel in mm


max. load in N

max. travel in mm

8 8 71 141 2 71 141 2 8 13 - - - - - - 10 10 87 215 2,5 87 217 2,5 10 15 47 175 3,75 47 175 3,75 10 20 - - - - - - 15 10 - - - 205 410 2 15 15 100 385 3,75 100 385 3,75 15 20 120 590 5 120 590 5 15 30 52 390 7,5 52 390 7,5 20 10 375 940 2,5 375 940 2,5 20 15 190 705 3,75 190 705 3,75 20 20 160 810 5 160 810 5 20 25 170 1055 6,25 - - - 20 30 115 850 7,5 115 850 7,5 25 15 435 1630 3,75 435 1630 3,75 25 20 275 1380 5 275 1380 5 25 30 160 1190 7,5 160 1190 7,5 30 15 695 2610 3,75 695 2610 3,75 30 20 375 1880 5 375 1880 5 30 25 255 1590 6,25 255 1590 6,25 30 30 215 1620 7,5 215 1620 7,5 30 40 180 1785 10 - - - 40 20 950 4750 5 950 4750 5 40 25 660 4130 6,25 660 4130 6,25 40 30 375 2830 7,5 375 2830 7,5 40 40 315 3150 10 315 3150 10 50 20 1490 7450 5 1490 7450 5 50 30 725 5420 7,5 725 5420 7,5 50 40 495 4950 10 495 4950 10 50 50 415 4190 12,5 415 4190 12,5 60 20 2400 11990 5 2400 11990 5 60 30 1220 9180 7,5 1220 9180 7,5 60 40 465 4640 10 465 4640 10 60 50 580 7240 12,5 580 7240 12,5 60 60 540 8110 15 540 8110 15 70 30 1740 13070 7,5 1740 13070 7,5 70 40 1530 15280 10 1530 15280 10 70 55 690 9510 13,75 690 9510 13,75 75 25 3320 20780 6,25 3320 20780 6,25 75 30 2010 15090 7,5 2010 15090 7,5 75 40 915 9170 10 915 9170 10 75 50 1080 13550 12,5 1080 13550 12,5100 40 2420 24190 10 2420 24190 10100 50 1830 22900 12,5 1830 22900 12,5100 60 1430 21450 15 1430 21450 15125 55 1960 22190 11,25 1960 22190 11,25125 75 1270 23780 17,75 1270 23780 17,75

Type E Type S


| Load ratings

Load rating of levelling feet GN 30 / GN 32

d1 d2 Static load in kNVersions of threaded stemS / SK U / UK XRubber black

Rubber white

Rubber black

Rubber white

Rubber black

Rubber white

50 M 8 8 8 - - 8 8 50 M 10 10 10 - - 13 13 50 M 12 12 12 - - 16 13 50 M 16 - - 16 13 16 13 60 M 8 8 8 - - 8 8 60 M 10 10 10 - - 13 13 60 M 12 12 12 - - 16 13 60 M 16 - - 16 13 16 13 80 M 8 8 8 - - 8 8 80 M 10 10 10 - - 12 11 80 M 12 12 12 - - 12 11 80 M 16 - - 12 11 12 11 80 M 20 - - 12 11 12 11 80 M 24 - - 12 11 - -100 M 8 8 8 - - 8 8100 M 10 10 10 - - 11 10100 M 12 11 10 - - 11 10100 M 16 - - 11 10 11 10100 M 20 - - 11 10 11 10100 M 24 - - 11 10 - -120 M 20 - - 20 16 20 16120 M 24 - - 20 16 - -120 M 30 - - 20 16 - -

The static load bearing capacity given in the table rests on a test series in which the load has been applied perpendicular to the base plate. For the values given in the table, the strain relief may result in minor deformations of the base plate.

Bending and buckling stress which often occurs in practice results in a lower load bearing capacity of the adjustment spindle and may have to be taken into account.

Also, the spindle strength is assumed to be ≥ 500 N/mm2.

The details given on strength are non-binding guide values without any liabi-lity. In general, they do not constitute a warranty of quality.

The user must determine from case to case if a product is suitable for the intended pur-pose or use. Environmental factors may influ-ence the stated values.

Information


Load rating of Stainless Steel-Levelling feet GN 31 / GN 33

d1 d2 Static load in kNVersions of threaded stemS / SK T / TK and U / UK V / VK W XRubber black

Rubber white

Rubber black

Rubber white

Rubber black

Rubber white

Rubber black

Rubber white

Rubber black

Rubber white

50 M 8 8 8 - - - - - - 8 8 50 M 10 14 14 - - - - - - 13 13 50 M 12 20 20 - - - - - - 20 20 50 M 16 - - 28 28 - - - - 28 25 60 M 8 8 8 - - - - - - 8 8 60 M 10 14 14 - - - - - - 13 13 60 M 12 20 20 - - - - - - 20 20 60 M 16 - - 28 25 27 27 27 27 28 25 80 M 8 8 8 - - - - - - 8 8 80 M 10 14 14 - - - - - - 13 13 80 M 12 19 15 - - - - - - 15 15 80 M 16 - - 19 15 24 24 24 24 19 15 80 M 20 - - 19 15 24 24 24 24 19 15 80 M 24 - - 19 15 24 24 24 24 -100 M 8 8 8 - - - - - - 8 8100 M 10 14 14 - - - - - - 13 13100 M 12 17 14 - - - - - - 17 14100 M 16 - - 17 14 21 21 21 21 17 14100 M 20 - - 17 14 21 21 21 21 17 14100 M 24 - - 17 14 21 21 21 21 - -120 M 20 - - 25 22 - - - - 25 22120 M 24 - - 25 22 - - - - - -120 M 30 - - 25 22 - - - - - -

The static load bearing capacity given in the table rests on a test series in which the load has been applied perpendicular to the base plate. For the values given in the table, the strain relief may result in minor deformations of the base plate.





Information

| Load ratings

Load rating of levelling feet GN 40 / GN 42

d1 d2 Static load Fs in kNVersions of threaded stem

GN 40 GN 42

drop shape

GN 42

rectangular shape

S / SK

U / UK

X

40 - - M 8 7 - 740 - - M 10 7 - 740 - - M 12 7 - 740 - - M 16 - 7 750 50 - M 8 8 - 850 50 - M 10 8 - 850 50 - M 12 8 - 850 50 - M 16 - 8 860 60 - M 8 8 - 860 60 - M 10 10 - 1060 60 - M 12 10 - 1060 60 - M 16 - 10 1080 80 80 80 8 - 880 80 80 80 10 - 1080 80 80 80 12 - 1280 80 80 80 - 12 1280 80 80 80 - 16 1680 80 80 80 - 16 -

The static load bearing capacity given in the table rests on a test series in which the load has been applied perpendicular to the base plate (without rubber underlay). For the valu-es given in the table, the strain relief may re-sult in minor deformations of the base plate.

Bending and buckling stress which oftenoc-curs in practice results in a lower load bea-ring capacity of the adjustment spindle and may have to be taken into account.




Information


Load rating of Stainless Steel-Levelling feet GN 41 / GN 44 / GN 43 / GN 45

d1 d2 Static load in kNVersions of threaded stem

GN 41 / GN 44 GN 43 / GN 45

drop shape

GN 43

rect. shape

S / SK

T / TK and

U / UK

V / VK

W

X

40 - - M 8 8 - - - 840 - - M 10 12 - - - 1240 - - M 12 12 - - - 1240 - - M 16 - 12 - - 1250 50 - M 8 8 - - - 850 50 - M 10 14 - - - 1450 50 - M 12 14 - - - 1450 50 - M 16 - 14 - - 1460 60 - M 8 8 - - - 860 60 - M 10 14 - - - 1460 60 - M 12 16 - - - 1660 60 - M 16 - 16 16 16 1680 80 80 M 8 8 - - - 880 80 80 M 10 14 - - - 1480 80 80 M 12 20 - - - 2080 80 80 M 16 - 20 20 20 2080 80 80 M 20 - 20 20 20 2080 80 80 M 24 - 22 22 22 -

The static load bearing capacity given in the table rests on a test series in which the load has been applied perpendicular to the base plate (without rubber underlay). For the valu-es given in the table, the strain relief may re-sult in minor deformations of the base plate.





Information

| Load ratings

Load rating of Stainless Steel-Levelling feet GN 21 / GN 23

d1 d2 Static load in kNVersions of threaded stem S / SK T / TK and U / UK V / VK W X

80 M 8 6 - - - 17 80 M 10 11 - - - 17 80 M 12 16 - - - 17 80 M 16 - 17 21 25 17 80 M 20 - 28 35 35 28 80 M 24 - 46 52 52 -100 M 8 6 - - - 17100 M 10 11 - - - 17100 M 12 16 - - - 17100 M 16 - 17 21 25 17100 M 20 - 28 35 35 28100 M 24 - 46 52 52 -120 M 20 - 28 - - 28120 M 24 - 46 - - -120 M 30 - 43 - - -

At a spindle thread size M 10 and higher, the static load of the Stainless Steel-Levelling feet GN 21 / GN 23 is limited owing to the permissible contact pressure of the adjust-ment spindle acting on the base plate (at a spindle strength ≥ 500 N/mm2). The values given in the table (valid for type D0 without rubber underlay) assume a clean pressure load perpendicular to the base plate. Ben-ding and buckling stress which often occurs in practice results in a lower load-bearing capacity of the adjustment spindle and may have to be taken into account.



Information

|Extract from DIN / ISO standard Page 1477

DIN 228 Pipe threadsExtract

No

min

al

thre

ad

siz

e

Gradient P Bolt thread Nut thread

Num

ber

of g

ears

of

25,

4 m

m

equa

l to

mm

Major-Ø d Pitch-Ø d2 Minor-Ø d1 Major-Ø D Pitch-Ø D2 Minor-Ø D1

max. min. max. min. A min. B max. min. max. min. min. max. min. max.

G ⅛ 28 0,907 9,728 9,514 9,174 9,040 8,933 8,566

not

spec

ified

not

spec

ified

9,728 9,254 9,147 8,848 8,566G ¼ 19 1,337 13,157 12,907 12,301 12,176 12,051 11,445 13,157 12,426 12,301 11,890 11,445G ⅜ 19 1,337 16,662 16,412 15,806 15,681 15,556 14,950 16,662 15,931 15,806 15,395 14,950G ½ 14 1,814 20,955 20,671 19,793 19,651 19,509 18,631 20,955 19,935 19,793 19,172 18,631G ⅝ 14 1,814 22,911 22,627 21,749 21,607 21,465 20,587 22,911 21,891 21,749 21,128 20,587G ¾ 14 1,814 26,441 26,157 25,279 25,137 24,995 24,117 26,441 25,421 25,279 24,658 24,117G ⅞ 14 1,814 30,201 29,917 29,039 28,897 28,755 27,877 30,201 29,181 29,039 28,418 27,877G 1 11 2,309 33,249 32,889 31,770 31,590 31,410 30,291 33,249 31,950 31,770 30,931 30,291G 1⅛ 11 2,309 37,897 37,537 36,418 36,238 36,058 34,939 37,897 36,598 36,418 35,579 34,939G 1¼ 11 2,309 41,910 41,550 40,431 40,251 40,071 38,952 41,910 40,611 40,431 39,592 38,952G 1½ 11 2,309 47,803 47,443 46,324 46,144 45,964 44,845 47,803 46,504 46,324 45,485 44,845G 1¾ 11 2,309 53,746 53,386 52,267 52,087 51,907 50,788 53,746 52,447 52,267 51,428 50,788G 2 11 2,309 59,614 59,254 58,135 57,955 57,775 56,656 59,614 58,315 58,135 57,296 56,656

The pitch-diameter d2 of the bolt thread has 2 tolerance classes, namely A and B.

The nut thread has only 1 tolerance class.

The metal pipe threads listed in this catalogue are made in the "more accurate" tolerance class A.

For threads in plastic standard parts this tolerance class can as a rule not be maintained for production-orientated reasons.

Description

| Extract from DIN / ISO standard

DIN 13 Metric ISO threadExtract Tolerance fields 6g / 6H

No

min

al

thre

ad

-Ø

Gra

die

nt

P Bolt thread 6g Nut thread 6HMajor-Ø d Pitch-Ø d2 Minor-Ø d1 Major-Ø D Pitch-Ø D2 Minor-Ø D1

max. min. max. min. max. min. min. max. min. max. min. max.

M 3 0,5 2,980 2,874 2,655 2,580 2,367 2,273 3,000

not

spec

ified

2,675 2,775 2,459 2,599M 4 0,7 3,978 3,838 3,523 3,433 3,119 3,002 4,000 3,545 3,663 3,242 3,422M 5 0,8 4,976 4,826 4,456 4,361 3,995 3,869 5,000 4,480 4,605 4,134 4,334M 6 1 5,974 5,794 5,324 5,212 4,747 4,596 6,000 5,350 5,500 4,917 5,153M 8 1,25 7,972 7,760 7,160 7,042 6,438 6,272 8,000 7,188 7,348 6,647 6,912M 10 1,5 9,968 9,732 8,994 8,862 8,128 7,938 10,000 9,026 9,206 8,376 8,676M 12 1,75 11,966 11,701 10,829 10,679 9,819 9,602 12,000 10,863 11,063 10,106 10,441M 14 2 13,962 13,682 12,663 12,503 11,508 11,271 14,000 12,701 12,913 11,835 12,210M 16 2 15,962 15,682 14,663 14,503 13,508 13,274 16,000 14,701 14,913 13,835 14,210M 20 2,5 19,958 19,623 18,334 18,164 16,891 16,625 20,000 18,376 18,600 17,294 17,744M 24 3 23,952 23,577 22,003 21,803 20,271 19,955 24,000 22,051 22,316 20,752 21,252

The limiting sizes for standard threads given in the table comply with

- tolerance field 6g for bolt threads - tolerance field 6H for nut threads.

The metric steel and metal threads specified in this catalogue are based on the tolerance fields given above.

For threads in plastic standard parts (without steel or metallic thread insert) this tolerances can as a rule not be maintained for production-orientated reasons.

Description


DIN 13 Metric ISO fine threadExtract Tolerance fields 6g / 6H

No

min

al

thre

ad

-Ø

Gra

die

nt

P Bolt thread 6g Nut thread 6HMajor-Ø d Pitch-Ø d2 Minor-Ø d1 Major-Ø D Pitch-Ø D2 Minor-Ø D1

max. min. max. min. max. min. min. max. min. max. min. max.

M 5 0,5 4,980 4,874 4,655 4,580 4,367 4,273 5,000

not

spec

ified

4,675 4,775 4,459 4,599M 6 0,5 5,980 5,874 5,655 5,570 5,367 5,263 6,000 5,675 5,787 5,459 5,599M 8 0,5 7,980 7,874 7,655 7,570 7,367 7,263 8,000 7,675 7,787 7,459 7,599M 10 0,5 9,980 9,874 9,655 9,570 9,367 9,263 10,000 9,675 9,787 9,459 9,599M 12 0,5 11,980 11,874 11,655 11,565 11,367 11,258 12,000 11,675 11,793 11,459 11,599M 6 0,75 5,978 5,838 5,491 5,391 5,058 4,929 6,000 5,513 5,645 5,188 5,378M 8 0,75 7,978 7,838 7,491 7,391 7,058 6,929 8,000 7,513 7,645 7,188 7,378M 10 0,75 9,978 9,838 9,491 9,391 9,058 8,929 10,000 9,513 9,645 9,188 9,378M 12 0,75 11,978 11,838 11,491 11,385 11,058 10,923 12,000 11,513 11,653 11,188 11,378M 16 0,75 15,978 15,838 15,491 15,385 15,058 14,923 16,000 15,513 15,653 15,188 15,378M 8 1 7,974 7,794 7,324 7,212 6,747 6,596 8,000 7,350 7,500 6,917 7,153M 10 1 9,974 9,794 9,324 9,212 8,747 8,596 10,000 9,350 9,500 8,917 9,153M 12 1 11,974 11,794 11,324 11,206 10,747 10,590 12,000 11,350 11,510 10,917 11,153M 16 1 15,974 15,794 15,324 15,206 14,747 14,590 16,000 15,350 15,510 14,917 15,153M 20 1 19,974 19,794 19,324 19,206 18,747 18,590 20,000 19,350 19,510 18,917 19,153M 12 1,5 11,968 11,732 10,994 10,854 10,128 9,930 12,000 11,026 11,216 10,376 10,676M 14 1,5 13,968 13,732 12,994 12,854 12,128 11,930 14,000 13,026 13,216 12,376 12,676M 16 1,5 15,968 15,732 14,994 14,854 14,128 13,930 16,000 15,026 15,216 14,376 14,676M 18 1,5 17,968 17,732 16,994 16,854 16,128 15,930 18,000 17,026 17,216 16,376 16,676M 20 1,5 19,968 19,732 18,994 18,854 18,128 17,930 20,000 19,026 19,216 18,376 18,676M 22 1,5 21,968 21,732 20,994 20,854 20,128 19,930 22,000 21,026 21,216 20,376 20,676M 26 1,5 25,968 25,732 24,994 24,844 24,128 23,920 26,000 25,026 25,226 24,376 24,676M 27 1,5 26,968 26,732 25,994 25,844 25,128 24,920 27,000 26,026 26,226 25,376 25,676M 30 1,5 29,968 29,732 28,994 28,844 28,128 27,920 30,000 29,026 29,226 28,376 28,676M 35 1,5 34,968 34,732 33,994 33,844 33,128 32,920 35,000 34,026 34,226 33,376 33,676M 40 1,5 39,968 39,732 38,994 38,844 38,128 37,920 40,000 39,026 39,226 38,376 38,676M 20 2 19,962 19,682 18,663 18,503 17,508 17,271 20,000 18,701 18,913 17,835 18,210M 24 2 23,962 23,682 22,663 22,493 21,508 21,261 24,000 22,701 22,925 21,835 22,210M 30 2 29,962 29,682 28,663 28,493 27,508 27,261 30,000 28,701 28,925 27,835 28,210M 36 2 35,962 35,682 34,663 34,493 33,508 33,261 36,000 34,701 34,925 33,835 34,210M 42 2 41,962 41,682 40,663 40,493 39,508 39,261 42,000 40,701 40,925 39,835 40,210

Description

The limiting sizes for standard threads given in the table comply with - tolerance field 6g for bolt threads - tolerance field 6H for nut threads.

The metric steel and metal threads specified in this catalogue are based on the tolerance fields given above.

For threads in plastic standard parts (without steel or me-tallic thread insert) this tolerances can as a rule not be maintained for production-orientated reasons.

| Extract from DIN / ISO standard

DIN ISO 286 ISO-Fundamental tolerancesExtract Part 1 Numerical values

Tol. grades IT

Nominal size range—

… 3> 3

… 6> 6

… 10> 10

… 18> 18

… 30> 30

… 50> 50

… 80> 80

… 120> 120

… 180> 180

… 250> 250

… 315> 315

… 400> 400

… 50001 0,3 0,4 0,4 0,5 0,6 0,6 0,8 1 1,2 2 2,5 3 4 0 0,5 0,6 0,6 0,8 1 1 1,2 1,5 2 3 4 5 6 1 0,8 1 1 1,2 1,5 1,5 2 2,5 3,5 4,5 6 7 8 2 1,2 1,5 1,5 2 2,5 2,5 3 4 5 7 8 9 10 3 2 2,5 2,5 3 4 4 5 6 8 10 12 13 15 4 3 4 4 5 6 7 8 10 12 14 16 18 20 5 4 5 6 8 9 11 13 15 18 20 23 25 27 6 6 8 9 11 13 16 19 22 25 29 32 36 40 7 10 12 15 18 21 25 30 35 40 46 52 57 63 8 14 18 22 27 33 39 46 54 63 72 81 89 97 9 25 30 36 43 52 62 74 87 100 115 130 140 15510 40 48 58 70 84 100 120 140 160 185 210 230 25011 60 75 90 110 130 160 190 220 250 290 320 360 40012 100 120 150 180 210 250 300 350 400 460 520 570 63013 140 180 220 270 330 390 460 540 630 720 810 890 97014 250 300 360 430 520 620 740 870 1000 1150 1300 1400 155015 400 480 580 700 840 1000 1200 1400 1600 1850 2100 2300 250016 600 750 900 1100 1300 1600 1900 2200 2500 2900 3200 3600 400017 1000 1200 1500 1800 2100 2500 3000 3500 4000 4600 5200 5700 630018 1400 1800 2200 2700 3300 3900 4600 5400 6300 7200 8100 2200 9700

Tolerances in μm

This ISO Standard represents the basis for a system of limi-ting sizes and fits whereby the table mirrors the calculated values of fundamental tolerances in connection with funda-mental dimensions.

The use of this table is limited to smooth circular cylindri-cal workpieces or such with two parallel fitting planes or contact areas.

The numerical values attributed to an ISO tolerance grade (IT) specify the size of the tolerance and hence the toleran-ce field. With ascending numbers, the size of the tolerance increases.

For identification purposes of the position of the tolerance field in relation to the nominal dimension (zero), the number chosen as tolerance grade IT is preceded by a letter.

Tolerance area H is the most common value for bores. It specifies that the minimum dimension of the bore corre-sponds to the nominal dimension. The permissible maxi-mum dimension corresponds to the nominal dimension plus the IT tolerance.

Description

min. dimension: 8,000 max. dimension: 8,090

Bore 8 H11 = 8 +0,090 0Bore 20 H7 = 20 +0,021

0

min. dimension: 20,000 max. dimension: 20,021

Examples


DIN ISO 286 ISO-Fundamental tolerancesExtract Part 2 for bores and shafts

Tolerance classes for shaft

Nominal size range– ... 3

> 3 ... 6

> 6 ... 10

> 10 ... 18

> 18 ... 30

> 30 ... 50

> 50 ... 80

> 80 ... 120

> 120 ... 180

> 180 ... 250

f 7 – 6 – 10 – 13 – 16 – 20 – 25 – 30 – 36 – 43 – 50– 16 – 22 – 28 – 34 – 41 – 50 – 60 – 71 – 83 – 96

f 9 – 6 – 10 – 13 – 16 – 20 – 25 – 30 – 36 – 43 – 50– 31 – 40 – 49 – 59 – 72 – 87 – 104 – 123 – 143 – 165

g 6 – 2 – 4 – 5 – 6 – 7 – 9 – 10 – 12 – 14 – 15– 8 – 12 – 14 – 17 – 20 – 25 – 29 – 34 – 39 – 44

h 6 0 0 0 0 0 0 0 0 0 0– 6 – 8 – 9 – 11 – 13 – 16 – 19 – 22 – 25 – 29

h 7 0 0 0 0 0 0 0 0 0 0– 10 – 12 – 15 – 18 – 21 – 25 – 30 – 35 – 40 – 46

h 8 0 0 0 0 0 0 0 0 0 0– 14 – 18 – 22 – 27 – 33 – 39 – 46 – 54 – 63 – 72

h 9 0 0 0 0 0 0 0 0 0 0– 25 – 30 – 36 – 43 – 52 – 62 – 74 – 87 – 100 – 115

h 11 0 0 0 0 0 0 0 0 0 0– 60 – 75 – 90 – 110 – 130 – 160 – 190 – 220 – 250 – 290

h 13 0 0 0 0 0 0 0 0 0 0– 140 – 180 – 220 – 270 – 330 – 390 – 460 – 540 – 630 – 720

h 14 0 0 0 0 0 0 0 0 0 0– 250 – 300 – 360 – 430 – 520 – 620 – 740 – 870 – 1000 – 1150

js 14 + 125 + 150 + 180 + 215 + 260 + 310 + 370 + 435 + 500 + 575– 125 – 150 – 180 – 215 – 260 – 310 – 370 – 435 – 500 – 575

n 6 + 10 + 16 + 19 + 23 + 28 + 33 + 39 + 45 + 52 + 60+ 4 + 8 + 10 + 12 + 15 + 17 + 20 + 23 + 27 + 31

p 6 + 12 + 20 + 24 + 29 + 35 + 42 + 51 + 59 + 68 + 79+ 6 + 12 + 15 + 18 + 22 + 26 + 32 + 37 + 43 + 50

Tolerances in μm

Tolerance classes for bore

Nominal size range– ... 3

> 3 ... 6

> 6 ... 10

> 10 ... 18

> 18 ... 30

> 30 ... 50

> 50 ... 80

> 80... 120

> 120 ... 180

> 180 ... 250

D 9 + 45 + 60 + 76 + 93 + 117 + 142 + 174 + 207 + 245 + 285 + 20 + 30 + 40 + 50 + 65 + 80 + 100 + 120 + 145 + 170

D 12 + 120 + 150 + 190 + 230 + 275 + 330 + 400 + 470 + 545 + 630 + 20 + 30 + 40 + 50 + 65 + 80 + 100 + 120 + 145 + 170

E 8 + 28 + 38 + 47 + 59 + 73 + 89 + 106 + 126 + 148 + 172+ 14 + 20 + 25 + 32 + 40 + 50 + 60 + 72 + 85 + 100

F 7 + 16 + 22 + 28 + 34 + 41 + 50 + 60 + 71 + 83 + 96+ 6 + 10 + 13 + 16 + 20 + 25 + 30 + 36 + 43 + 50

G 6 + 8 + 12 + 14 + 17 + 20 + 25 + 29 + 34 + 39 + 44+ 2 + 4 + 5 + 6 + 7 + 9 + 10 + 12 + 14 + 15

G 7 + 12 + 16 + 20 + 24 + 28 + 34 + 40 + 47 + 54 + 61+ 2 + 4 + 5 + 6 + 7 + 9 + 10 + 12 + 14 + 15

H 7 + 10 + 12 + 15 + 18 + 21 + 25 + 30 + 35 + 40 + 46 0 0 0 0 0 0 0 0 0 0

H 8 + 14 + 18 + 22 + 27 + 33 + 39 + 46 + 54 + 63 + 72 0 0 0 0 0 0 0 0 0 0

H 9 + 25 + 30 + 36 + 43 + 52 + 62 + 74 + 87 + 100 + 115 0 0 0 0 0 0 0 0 0 0

H 10 + 40 + 48 + 58 + 70 + 84 + 100 + 120 + 140 + 160 + 185 0 0 0 0 0 0 0 0 0 0

H 11 + 60 + 75 + 90 + 110 + 130 + 160 + 190 + 220 + 250 + 290 0 0 0 0 0 0 0 0 0 0

H 12 + 100 + 120 + 150 + 180 + 210 + 250 + 300 + 350 + 400 + 460 0 0 0 0 0 0 0 0 0 0

H 13 + 140 + 180 + 220 + 270 + 330 + 390 + 460 + 540 + 630 + 720 0 0 0 0 0 0 0 0 0 0

H 14 + 250 + 300 + 360 + 430 + 520 + 620 + 740 + 870 + 1000 + 1150 0 0 0 0 0 0 0 0 0 0

JS 9 + 12,5 + 15 + 18 + 21,5 + 26 + 31 + 37 + 43,5 + 50 + 57,5– 12,5 – 15 – 18 – 21,5 – 26 – 31 – 37 – 43,5 – 50 – 57,5

N 9 – 4 0 0 0 0 0 0 0 0 0– 29 – 30 – 36 – 43 – 52 – 62 – 74 – 87 – 100 – 115

P 9 – 6 – 12 – 15 – 18 – 22 – 26 – 32 – 37 – 43 – 50– 31 – 42 – 51 – 61 – 74 – 88 – 106 – 124 – 143 – 165

Tolerances in μm

|Technical information Page 1482

DIN EN ISO 898-1 DIN EN 20 898-2 Strength valuesExtract Extract of screws / nuts

Strength classes of screws4.6 5.6 5.8 6.8 8.8 10.9 12.9

Nominal tensile strength Rm, nom. in N/mm2 400 500 500 600 800 1000 1200Lower yield point ReL in N/mm2 240 300 400 480 – – –0,2 %-Yield limit Rp 0.2 in N/mm2 – – – – 640 900 1080Tension under test force Sp in N/mm2 225 280 380 440 580 830 970Elongation A in % 22 20 – – 12 9 8

The strength class identification number consists of two numerals:

• The first number corresponds to 1/100 of the nominal tensile strength in N/mm2 (see table)

• The second number shows ten times the ratio of lower yield point ReL (or 0.2 %-yield limit Rp 0,2) to the nominal tensile strength Rm, nom (yield point ratio).

Example: Strength class 5.8 means: Minimum tensile strength Rm = 500 N/mm2, Minimum yield point ReL = 400 N/mm2

Also, multiplying both numerals results in 1/10 of the yield point in N/mm2.

The designation of a strength class consists of a identification number which provides information on the test tension of the material used:

Identification number x 100 = Test tension Sp

The test tension is equal to the minimum tensile strength in N/mm2 of a screw which, if paired with the appropriate nut, can be loaded up to the minimum yield point of the screw.

Example: Screw 8.8 – Nut 8, connection can be loaded up to the minimum yield point of the screw.

Test tension Sp in N/mm2 for thread

Strength classes of nuts5 6 8 10 12

… M 4 520 600 800 1040 1150above M 4 … M 7 580 670 855 1040 1150above M 7 … M 10 590 680 870 1040 1160above M 10 … M 16 610 700 880 1050 1190above M 16 … M 39 630 720 920 1060 1200

Features

Features


Example:

Proximity switch GN 896.1 → Page 584 Protection class: IP 67

DIN EN 60529 / VDE 0470-1 IP-Protection classesExract

The IP code indicates the level of protection that a device, such as an electronic switch, receives from its housing.

First identification number: Degree of protection (protection against foreign particles)

1

Protection against ingress of solid foreign particles with a diameter larger than 50 mm, no access with the back of the hand

2Protection against ingress of solid foreign particles with a diameter larger than 12 mm, no access with fingers

3Protection against ingress of solid foreign particles with a diameter larger than 2,5 mm, e.g. tools

4Protection against ingress of solid foreign particles with a diameter larger than 1 mm, e.g. wires

5Protection against the penetration of dust in harmful quantities (dust protection)

6 Protection against any dust pen-etration (dust-proof)

Second identification number: Degree of protection (water protection)

1 Protection against vertically falling drops of water

2 Protection against dripping water falling at an angle of up to 15°

3 Protection against spray water falling at an angle of up to 60°

4Protection against water splashing on all sides / spraying water

5 Protection against a water stream, acting from any angle

6 Protection against a strong water stream, acting from any angle

7Protection against water during temporary submersion (up to 30 minutes, 1 m depth)

8 Protection against water during sustained submersion

| Material characteristics

Material characteristics of plastics materials and Elastomers

Information

The above details are general values without claiming to be complete. Material properties may vary widely through addi-tives, modifications and environmental influence factors.

The details are unsuitable as the sole basis for constructions. The data may not be used in place of tests to determine the suitability of a material for a specific purpose.

No warranty or liability will be accepted fort the above specifications and details.

The essential plastic materials used for GANTER and ELESA products are listed in the following tables.

Duroplast Technopolymer Elastomers Thermoplastic Elastomers

This group includes plastic materials which solidify by chemical reactions. They closely crosslink into spatial lattice patterns of macromolecules which gives Duroplast material high mechanical strength and surface hardness. Their elasticity is low, how-ever.

The curing process is irreversible. Un-like Technopolymer, Duroplast can-not be melted because it is rigid up to degradation temperature. Phenolic resins are among the most commonly used Duroplast materials.

In general, the molecular crosslinking of Duroplast creates good chemical stability.

The coloring options of components made of Duroplast are limited.

With increasing temperature and once the softening point is exceeded, this group of Technopolymer melts, can be heat distorted and solidifies again after cooling. This process can be repeated any number of times. Un-like Duroplast, there is no chemical reaction during processing.

Technopolymer materials can be sub-divided into amorphous and partially crystalline plastics. The disordered structure of amorphous materials al-lows the production of transparent components by injection moulding right through to crystal-clear parts. Partially crystalline Technopolymer have a structure resulting in enhan-ced mechanical properties and tem-peratures of use.

The wide variety of different Tech-nopolymer and their options of mo-difications allow the production of “tailor-made” construction materials with respect to mechanical proper-ties, chemical resistance, tempera-ture resistance and different colors.

A feature of elastomers is that they can be deformed under minimal ten-sile or compressive stress. When the force effect decreases or no longer exists, the parts automatically return to their original, undeformed shape. Thus, they demonstrate the typical behavior of rubber.

In chemical terms, these are macro-molecules which are interconnected by only a few chemical crosslinking bridges.

With thermoplastic elastomers, the cross-links soften under the influence of heat, thus demonstrating a thermo-plastic behavior.

By way of modification, elastomers can be made in varying degrees of hardness. They can be dyed easily by adding color pigments.

Material characteristics of Elastomers → Page 1487 ff.

The plastic materials used for GANTER and ELESA products can be classed in three main groups:

|Material characteristics Page 1485

Duroplast TechnopolymerSymbol PF 31 PA 6 PA 6 GF30 PA-TDescription

Phenolic resin PolyamidePolyamide with 30 % glass fibre

Polyamide transparent

Yield stress in MPa – 80 / 50 – / – 90Tensile strength in MPa 60 – / – 180 / 110 –Tension-E-Module in MPa 9000 3000 / 1500 9000 / 6500 2800

Ball indentation hardness in MPa 250 150 / 70 220 / 150 140

Temperature resistance:• max. short-term • max. long-term • min. application temp.

180 °C 140 °C –20 °C

180 °C 90 °C –40 °C

200 °C 120 °C –40 °C

180 °C 90 °C –30 °C

Resistance to: *• Oil, greases • Solvents: Tri Per • Acid: weak strong • Alkalines: weak strong • Petrol • Alcohol • hot water • UV light / weather exposure

+ o o + – + – + + o –

+ + + o – + o + + o o

+ + + o – o – + + o o

+ + + – – + + + – – o

Fire behaviour (UL 94) V-0 HB HB V-2General This Duroplast

material on phenolic resin basis with organic filler has the following properties:

High stiffness and hardness, low tendency to creep, high heat forming resistance, low ther-mal linear expan-sion, high surface slip resilience, low flammability.

Phenolic resins are available only in dark colour shades. They are not suitab-le for use with food.

Typical applications include thermally insulating operating elements.

The material group Polyamide 6 (partially crystalline) offers uni-versal materials for mechanical function components in mechani-cal engineering.

Polyamides are: - cold-temperature resistant - impact stress resilient and impact resistant - abrasion resistant

Reinforced Polyamides such as PA 6 GF30 combine high stiffness and rigidity with extreme impact strength, properties which make them highly robust under mechanical stress.

Polyamide PA-T (amorphous) is translucent with a slightly yellow transparency. Typically used for oil level sight glass.

* + resistant, o conditionally resistant, – non-resistant

Material characteristics of plastics materials and Elastomers continued


TechnopolymerSymbol PE-HD PE-LD POM-C POM-HDescription Polyethylen

high densityPolyethylen low density

Polyacetal (Copolymer)

Polyacetal (Homopolymer)

Yield stress in MPa 30 10 65 72Tensile strength in MPa 25 ... 30 8 ... 10 – 70Tension-E-Module in MPa 1450 200 2700 3100Ball indentation hardness in MPa 57 (Standard H132/30) 15 (Standard H49/30) 145 174


100 °C 90 °C -80 °C

100 °C 70 °C – 80 °C

140 °C 90 °C –50 °C

140 °C 80 °C –50 °C


+ + + + + + + + + + o

+ – – + – + + + + o o

+ – + + – + + + + + o

+ – + + – + + + + o o

Fire behaviour (UL 94) HB HB HB HBGeneral PE is a very versatile thermoplastic polymer.

It is colorless in its basic form.

PE is physiologically safe, practically odor-less, and tasteless. These properties make it ideal for the food and packaging industry. PE is shockproof and impact-resistant. It has good sliding properties and absorbs virtually no moisture.

Polyacetals (partially crystalline) are universal materials used in function components for precision engineering and in apparatus construction. They feature excellent properties: - low friction resistance - good abrasion resistance - good resilience - good fatigue resistance - good chemical resistance Typical applications include snap-fit elements (form-locking connecting elements).




TechnopolymerSymbol PC PP GF20 PSUDescription

PolycarbonatePolypropylene with 20% glass fibre

Polysulfon

Yield stress in MPa 63 33 70Tensile strength in MPa – – 70Tension-E-Module in MPa 2400 2900 2400Ball indentation hardness in MPa 110 80 147 (H358/30)


140 °C 125 °C – 100 °C

140 °C 100 °C 0 °C

180 °C 160 °C – 100 °C


o – – + – – – – o – o

+ o o + + + + + + + o

+ o o o o + + – + + -

Fire behaviour (UL 94) V-2 – V-0General Polycarbonates

(amorphous) are translu-cent plastic materials with following properties: High strength, in particular high impact resistance, good optical properties, self-extinguishing. but: sensitive to chemicals and stress cracking, not suita-ble for high dynamic stress loads, notch sensitive at edges and corners.

Propylenes (partially crystalline) are universal standard plastic materials with balanced property levels: Average strength, stiffness, impact resistance, low density, excellent chemical resistance but very bad cold temperature proper-ties. Embedded glass fibre, e.g. PP GF20, enhances stiffness and strength. Typical applications for propylenes are armatures.

The primary feature of PSU is its very high heat resis-tance and good resistance to chemicals.

Typical fields of application are electrical engineering, electronics, mechanical engineering, and medical technology where high heat resistance is needed, while also allowing transparency.




Elastomers

Symbol NR CR FPM, FKMTrade name Neoprene® Viton®

Chemical description

Natural rubber

Chloroprene rubber

Fluorine rubber Fluorine caoutchouc

Hardness (Shore A) 30 … 90 30 … 90 65 … 90Temperature resistance• short-term • long-term

– 60° … +130 °C – 40° … + 80 °C

– 30° … +150 °C – 25° … +100 °C

– 30° … +280 °C – 20° … +230 °C

Tensile strength in N/mm2

– 25 20

Wear resistance / Abrasion resistance

good good good

Resistance to: *• Oil, greases • Solvents • Acid • Alkalines • Petrol • UV light / weather exposure

- o o o - -

+ o + + - +

+ + + + + +

General NR is a material with very good physical properties and excellent mechanical strength. It is used e.g. for spring elements.

CR is one of the most frequently used synthetic rubbers with a wide range of applications for parts which require exceptional resistance to ageing.

FPM is unmatched for applica-tions with contact to fuels, oils, solvents, as well as many acids and caustic solutions; resistant to atmospheric and environ-mental influences.

Due to its high price its use is restricted to high quality rubber parts which are ex-posed to extremely heavy Wear resistance.

Viton® is a registered trademark of DuPont per-formance rubbers.





Elastomers

Symbol NBR H-NBR MVQ, VMQTrade name Perbunan® - Elastosil®


Acrylonitrile-butadiene rubber

Acrylonitrile-butadiene rubber

Silicone rubber

Hardness (Shore A) 25 … 95 85 3 ... 90Temperature resistance• short-term • long-term

– 40° … +150 °C – 30° … +120 °C

- – 25° … +150 °C

–50° ... +250 °C –30° ... +200 °C


25 11 12


good good good


+ o o + + -

+ + o + + +

o o - - o +

General NBR is a synthetic special rubber for rubber parts with high requirements for resistance to swelling when in contact with oils and fuels.

Standard material for o-rings.

H-NBR is obtained through full or partial hydrogenation of NBR. This significantly improves the resistance to heat, ozone and aging.

The resulting materials are characterized by high me-chanical strength and high abrasion resistance. Media resistance is comparable to NBR.

MVQ offers very good mechanical properties over a very wide temperature range with satisfactory oil resistance.

In comparison with other elastomers, MVQ has exceptionally high purity and is therefore used in particular in food and phar-maceutical applications.



Hardness data of vulcanized or thermoplastic elastomers are measured using the Shore scale. This value is determined by measuring the indention depth of a spring-loaded indenter into the material. A low indention depth is a high Shore value, a high indention depth a low Shore value.

Different indenter shapes are used depending on the materials being examined. The elastomer materials used in Ganter products are measured according to “Shore A” with a blunt indenter with a tip angle of 35°.

Information of hardness data for Elastomers

Elastomers

Symbol PUR TPE TPUTrade name Bayflex® Santoprene® Desmopan® /

Elastollan®


Polyurethane Thermoplastic rubber Thermoplastic Polyurethane rubber

Hardness (Shore A) 65 … 90 55 … 87 55 ... 85Temperature resistance• short-term • long-term

– 40° … +130 °C – 25° … +100 °C

– 40° … +150 °C – 30° … +125 °C

–50° ... +120 °C –30° ... + 90 °C


20 8,5 50


excellent good very good


+ o - - + +

+ + + + + +

+ - - o o +

General PUR is known for exceptionally good mechanical characteristics with very good resistance to atmospheric andenviron-mental influences.

In addition, the extreme resistance to tearing and to wear, should also be mentioned.

TPE is a thermoplastic rubber, the performance characteris-tics of which are compa-rable to those of many customary vulcanised special rubbers.

TPE is a multi-purpose material with outstanding dynamic fatigue strength and excellent resistance to ozone and atmospheric influences (environmental influences).

TPU has generally good physical properties, ma-king it ideal for demanding applications in virtually all industrial areas.

In addition to the very high wear and abrasion resis-tance, the excellent tear growth resistance and cold flexibility of the material at low temperatures should also be mentioned.

TPU can be made for a large hardness range and from an ergonomic point of view it can also be used advantageously due to its good surface feel (Softline!).




Material characteristics of Stainless Steel

AISI Standard 431 304 303 CF-8 Precison casting

German Material No. 1.4057 1.4301 1.4305 1.4308DIN / EN-Number EN 10088-3 EN 10088-3 EN 10088-3 EN 10213-4Symbol X 17 CrNi 16-2 X 5 CrNi 18-10 X 8 CrNiS 18-9 GX 5CrNi 19-10Alloying components %

C ≤ 0,12 ... 0,22 Cr 15,0 … 17,0 Ni 1,5 … 2,5

C ≤ 0,07 Cr 17,5 … 19,5 Ni 8,0 … 10,5

C ≤ 0,10 S ≤ 0,15 … 0,35 Cr 17,0 … 19,0 Ni 8,0 … 10,0

C ≤ 0,07 Cr 18,0 … 20,0 Ni 8,0 … 11,0

Minimum tensile strength Rm in N/mm2

800 … 950 500 … 700 500 … 700 440 … 640

Yield strength Rp0,2 in N/mm2 ≥ 600 ≥ 190 ≥ 190 ≥ 175

Machinability poor medium very good mediumForgeability medium good poor –Weldability good excellent poor goodSpecial characteristics

magnetic, martensitic structure for elements with high stability, can be used up to 400 °C

antimagnetic, austenitic structure suitable for low temperatures, can be used up to 700 °C

antimagnetic, austenitic structure


Corrosion resistance good

however, sensitive to intercrystalline corrosion

good

resistant to corrosion, in the natural environ-ment: water, rural and urban atmospheres without significant chloride or acid con-centrations, in food areas and in agricultural food areas

medium

due to the sulphur content reservations in environments which contain acids and chlorides

good

resistant to corrosion, Material is largely comparable with AISI 304

Main areas of application

Vehicle construction Chemical industry Aviation Machine construction Food industry

Food industry Agriculture Chemical industry Vehicle construction Construction industry Machine construction Decorative purposes (Kitchen equipment)

Vehicle construction Electronics Decorative purposes (Kitchen equipment) Machine construction

Food industry Beverage industry Packaging industry Fittings Pumps Agitators

The characteristics described should be treated as guidelines only. No guarantee is made. The exact conditions of use have to be taken into account individually.


AISI Standard 301 316 316 LHC Sintered Material

316 L (A4, bar steel)

German Material No. 1.4310 1.4401 (A4) 1.4404 1.4404 (A4)DIN / EN-Number EN 10088-3 EN 10088-3 Sint C40 EN 10088-3Symbol X 10 CrNi 18-8 X 5 CrNiMo 17-12-2 X 2 CrNiMo 17-13-2 X 2 CrNiMo 17-12-2Alloying components %

C ≤ 0,05 … 0,15 Mo ≤ 0,8 Cr 16,0 … 19,0 Ni 6,0 … 9,5

C ≤ 0,07 Cr 16,5 … 18,5 Ni 10,0 … 13,0 Mo 2,0 ... 2,5

C ≤ 0,08 Mo 2,0 … 4,0 Cr 16,0 … 19,0 Ni 10,0 … 14,0

C ≤ 0,03 Cr 16,5 … 18,5 Ni 10,5 … 13,0 Mo 2,0 ... 2,5


500 … 750 500 ... 700 330 500 ... 700

Yield strength Rp0,2 in N/mm2 ≥ 195 ≥ 200 ≥ 250 ≥ 200

Machinability poor medium – mediumForgeability good good – goodWeldability excellent good – excellentSpecial characteristics

antimagnetic, austenitic structure usable as spring steel up to 300 °C


antimagnetic structure


Corrosion resistance good

however, sensitive to intercrystalline corrosion

very good

significantly higher than AISI 304 in natural environmental mediums and moderate chlorine and salt concentra-tions, however not resistant to ocean water

medium

by virtue of its coarser porosity the corrosion resistance is in general reduced as compared with Stainless Steel, reservations espe-cially in acid and salty environment

very good

significantly higher than AISI 304 in natural environmental mediums and moderate chlorine and salt concentra-tions, however not resistant to ocean water


Springs for tempera-tures up to 300 °C Tools (knives) Plates for vehicle construction Chemical and food industry

Chemical industry Food industry Machine construction Building industry

Paint, oil, soap and textile industry Electronics Decorative purposes (Kitchen equipment)

Vehicle construction Chemical industry Food industry Medical / Pharmaceutical industry Building industry

Material characteristics of Stainless Steel continued




AISI Standard 316 630 304 Cu 316 Ti (A4)German Material No. 1.4408 1.4542 1.4567 1.4571 (A4)DIN / EN-Number EN 10213-4 EN 10088-3 EN 10088-3 EN 10088-3Symbol GX 5 CrNiMo 19-11-2 X 5 CrNiCuNb 16-4 X 3 CrNiCu 18-9-4 X 6 CrNiMoTi 17-12-2Alloying components %

C ≤ 0,07 Cr 18,0 … 20,0 Ni 9,0 … 12,0 Mo 2,0 ... 2,5

C ≤ 0,07 Cr 15,0 … 17,0 Ni 3,0 … 5,0 Cu 3,0 ... 5,0 Nb min. 5xC ... 0,45

C ≤ 0,04 Cr 17,0 … 19,0 Ni 8,5 … 10,5 Cu 3,0 ... 4,0

C ≤ 0,08 Mn ≤ 2,0 Cr 16,5 … 18,5 Ni 10,5 … 13,5 Mo 2,0 ... 2,5 Ti ≤ 5xC max. 0,7


440 ... 650 800 ... 1200 450 ... 650 500 ... 700

Yield strength Rp0,2 in N/mm2 ≥ 185 500 ... 1000 ≥ 175 ≥ 175

Machinability medium poor ... medium medium ... good medium ... poorForgeability - good good mediumWeldability good good good goodSpecial characteristics


antimagnetic, austenitic structure hardenable (precipitation harde-ning) suitable for low temperatures, can be used up to 450 °C

antimagnetic, austenitic structure suitable for cold forming

antimagnetic, austenitic structure suitable for low temperatures can be used up to 700 °C, high stability even at high temperatures

Corrosion resistance very good

acid-resistant

good

Corrosion resistance comparable with AISI 304, insensitive to inter-granular corrosion

good

resistant to corrosion in the natural environ-ment: water, rural and urban atmospheres without significant acid concentrations, in food areas and in agricultural food areas.

very good

comparable with 316 L


Food industry Chemical industry Fittings Pumps Machine construction

Shipbuilding Food industry Construction engi-neering Automotive industry Chemical industry Plant construction

Food industry Agriculture Chemical industry Machine construction Shipbuilding Electronics Screw industry

Equipment and pipeline construction Chemical industry Food industry Medical / Pharmaceutical industry Shipbuilding

Material characteristics of Stainless Steel continued

| Surface treatments

Surface treatmentsin alphabetical order

Anodizing Black oxide coating Chrome-plating

Anodizing is one of the most widely used methods for treating the surface of aluminum workpieces. In this sur-face treatment, an anodizing process is used in which the surface of the component is specifically oxidized electrolytically—the top layer con-verts into a stable oxide compound Al2O3. Changing the process param-eters allows the layer thickness to be varied between 5 and 25 μm and allows organic, inorganic, or electro-lytic coloration.

The surface treatment takes place in an electrolytic tank, whereby the workpiece acts as the anode and the sulfur or oxalic acid filing is the cath-ode. Usually direct current is used, which creates a weak flow of current between the two electrodes. The hy-drogen ions created in this process stimulate electrochemical corrosion on the aluminum surface, during which released atomic oxygen reacts with the metallic aluminum to form a hard oxide layer.

Anodizing is mainly used to give alu-minum workpieces better corrosion resistance. Introduction of dyes in the Al2O3 layer also allows anodizing to permanently color code components or visually enhance them – for exam-ple, by means of a red color.

Black-bronzed parts are only mini-mally protected against corrosion. The process is therefore, usually used to improve storage stability or for decorative reasons.

When the workpieces are placed in the hot black oxide solution, a chem-ical reaction creates a mixed oxide layer consisting of FeO and Fe2O3 with a maximum thickness of 1.5 μm. The dimensional accuracy is pre-served. The conversion layer is heat resistant up to about 300°C and is resistant to abrasion and bending, although it is too porous to provide adequate protection against corro-sion. This protection can be achieved through additional coatings for which the black-oxide layer acts as a primer. The process is standardized accord-ing to DIN 50938.

Chromium layers with thicknesses between 8 and 10 μm are used for decorative purposes and are avail-able as glossy or matte chrome-plat-ing from Ganter.

The process is galvanic process. Chromium ions are supplied from an aqueous solution with a chromic acid base.

Usually a combination of layers are necessary, whereby which the chro-mium always forms the top layer. For example, Ganter uses two-layer chrome-plating with nickel as the first layer and chromium as the top layer. The three-layer process is also used. Here the first layer is copper, the sec-ond nickel, and the final layer is chro-mium.

Chrome-plating is a comparably cost-intensive process that places high demands on occupational safe-ty and environmental protection due to the use of chromium(VI)-based electrolytes. Alternative electrolytes based on non-toxic chromium(III) are still in the testing phase.

|Surface treatments Page 1495

Electropolishing Galvanizing Nano-passivation

This electrochemical process reduc-es surface roughness and removes impurities, microfissures, and micro-structural defects in stainless steel parts. The workpiece is placed into an immersion bath containing mate-rial-specific electrolytes and forms the anode from which a thin metallic layer is removed after direct current is applied.

Electropolishing operates on the mi-cro-scale and removes rough peaks, while generating increased abrasion at the edges, which also makes elec-tropolishing ideal for fine deburring. The process is gentle on the structure since there is neither thermal nor me-chanical stress.

In addition to decorative applications, electropolished elements are used, for example, in the chemistry and food industry, in container construc-tion, or in medical technology.

This general term stands for various processes for the application of pure zinc layers to steel. In all cases, the objective is to protect the substrate against corrosion for as long as pos-sible.

The galvanic zinc-coating most com-monly used by Ganter uses a bath in which an electrolyte connects the workpiece which acts as the cathode to an anode made of pure zinc.

Depending on process parameters, the layer thicknesses which are de-posited in this way range from 2.5 to a maximum of 25 μm. The process, which is standardized according to DIN 50979, is mainly suitable for cor-rosion protection of small parts.

The zinc which is present on the sur-face may also be exposed to corro-sion depending on ambient condi-tions and is therefore subsequently protected by additional passivation to prevent zinc corrosion (white rust).

In addition, treatment with suitable chromium(VI)-free solutions creates a chromate layer, which considerably improves the corrosion resistance of the zinc coating. Dyes can also be in-troduced in this process step.

This process provides exceptionally good corrosion protection with min-imal layer thicknesses for die-cast zinc parts. The passivation layer is only 0.3 to 0.5 µm thick and does not affect dimensional accuracy. Ganter, usually uses an anthracite-colored layer.

The passivation consists of a chro-mium(III) layer and an overlying layer consisting of nanoscale SiO2 parti-cles which have self-healing proper-ties. If the surface becomes damaged down to the metallic substrate, the SiO2 particles migrate through the potential differences in a mobilized way to the unprotected area to re-close the layer.

Nano-passivation can be performed quickly and economically as a spray or immersion process—and is also a good primer for subsequent, further coatings, such as powder coating.

Surface treatments continued

| Surface treatments

Nickel-plating Powder coating Steam oxide coating

This term is a collective term for dif-ferent processes that are used to apply nickel to metallic substrates. Nickel-plating is divided mainly into galvanic and chemical nickel-plating.

With galvanic nickel-plating accord-ing to DIN EN ISO 1456, nickel ions are deposited from an electrolyte by the application of an electrical volt-age. The layer created in this way ap-pears silvery with a light yellow shade and is resistant to water and diluted acids and bases, but does not protect against tarnishing. Corrosion protec-tion is also only provided to a limited extent, as the layers, which are less than 25 μm thick, are usually porous and are therefore susceptible to pit-ting. Multi-layer systems with chromi-um as the top layer are more resistant in this respect.

Chemical nickel-plating, on the other hand, is not an electrochemical pro-cess. It is a reduction reaction of the surface of the part in the electrolyte bath, in which a uniform, non-po-rous nickel layer is formed. The end result provides very good protection against corrosive media, good abra-sion resistance, and high hardness – including for parts with complex geometries with interior surfaces. The nickel layer created in this way can be soldered and is non-ferromagnetic.

Powder coating, also known as plas-tic coating, usually refers to the elec-trostatic process variant. The powder, consisting of pigmented thermoplas-tic polymer or reactive binding agents made of epoxy resin, polyester resin, or acrylic resin, is applied to the work-piece.

Inside the spray nozzle, the powder accumulates a negative electrostat-ic charge, flows along the field lines to the grounded workpiece, and also reaches the rear of the workpiece. The electrostatic charge reduces overspray and ensures adhesion of the powder up to its thermal fusion.

The actual closed and homogeneous layer, with a thickness in the range from 100 to 200 µm, is not created until this step in the process. De-pending on powder type, the layers are highly resilient, weatherproof, and corrosion-resistant. They also can be produced in a wide variety of colors. Powder coating is very popular due to the ease of automation of the process and its economic feasibility.

This process is used for the post-treatment of hardened sintered parts for which black oxide coating using a saline solution cannot be used.

With steam oxidation, the sintered part is treated with water vapor at temperatures in excess of 350 °C. The result is a thin, almost black homoge-neous oxide layer of about 1 μm.

Steam oxide coating only increases corrosion resistance to a small extent.

Surface treatments continued

|Thread locking Page 1497

Polyamide patch coating PFB Polyamide complete coating PRBValues acc. to DIN 267 Part 28

Values for spring plungers GN 611 / GN 615.3

d l1 ≈ l2 ≈ Mmax. in Nm 1st Screw in

Mmin. in Nm1st Screw out

M ≈ in Nm1st Screw in / Screw out

d l1 ≈ l2 ≈ Mmax. in Nm 1st Screw in

Mmin. in Nm1st Screw out

M 3 1 … 1,5 4,5 0,43 0,1 0,3 M 12 x 1,5 2,5 5,5 15,5 2,3M 4 1,5 … 2 6 0,9 0,12 0,5 M 16 x 1,5 2,5 5,5 32 4M 5 1,5 … 2,5 7,5 1,6 0,18 0,6 M 20 x 1,5 2,5 7,5 54 7,5M 6 2 … 3 9 3 0,35 1,2 M 24 x 1,5 2,5 7,5 80 11,5M 8 2,5 … 4 12 6 0,85 2 M 27 x 1,5 2,5 7,5 94 13,5M 10 3 … 4,5 15 10,5 1,5 3,5 M 30 x 1,5 2,5 7,5 108 16M 12 3,5 … 5 18 15,5 2,3 5 M 33 x 1,5 2,5 7,5 122 18M 16 4 … 6 24 32 4 7M 20 5 … 7,5 30 60 5,4 10M 24 9 … 9 36 85 6,9 12

The polyamide patch coating PFB is a process where-by an elastic plastic material (Polyamide) is applied to a part of thread which creates a jamming action during the tightening of a nut. The coating can be produced either as a patch or complete coating. The axial play between the bolts and nut thread is taken up by the polyamide thus ensuring maximum surface pressure between the opposite uncoated thread flanks. This process counteracts the loo-sening and unscrewing on their own.

There is no cure time required, the thread contact is in-stantaneous resilient. The typical spray edge zone of the polyamide deposit prevents shear blasting. Polyamide patch coating is offered for GN 615.3

(→ Page 719) spring plungers. A blue coating indicates type K or KN, green indicates type KS or KSN (high spring load).

Polyamide complete coating is available for GN 252 and GN 252.5 blanking plugs (→ Page 791) as a type.

Features

Description

Information

- High thread locking action, shakeproof. Excellent conve-nient for adjusting bolts.

- The locking system is a captive component of the standard part, which eliminates the fitting of additional belay.

PFB PRB Thread locking with jamming actionPolyamide patch coating / Polyamide complete coating

The torque values are based on a test of a thread without preload with a nut thread 6H at room temperature. For PFB and thread lenghts l0 < l2, l2 is reduced in such a way that one to two thread turns are not coated at the end of the thread.

- Temperature resistant from – 60 °C up to 120 °C

- Approval for food areas

- High chemical stability

- Use is also possible, for instance, in oil-contaminated threaded holes

- Multi use is possible whereby the jamming effect after the 5th removal is around 50 % of its original strength.

| Thread locking

Features

MVK Thread locking gluingMicro encapsulation precote 80 (red)

d l1 l2 ≈ MIN in Nm max. insertion torque

MLB in Nmmin. breakaway torque

MOUT in Nmmax. loosening torque

M 5 1,5 … 2,5 7,5 0,5 1 6,5M 6 2 … 3 9 0,8 1,8 10M 8 2,5 … 4 12 1,5 4 26M 10 3 … 4,5 15 3 10 55M 12 3,5 … 5 18 5 16 95M 16 4 … 6 24 11 35 250M 20 5 … 7,5 30 14 45 500

The principle of micro encapsulation MVK (gluing) consists of a liquid plastic material and hardener encapsulated in a thin polymer film which is embedded in a lacquer like car-rier deposited in patch form an a thread. This patch dries and the component can be stored and handled in a normal manner.

When fitting a bolt with this patch the two capsules will burst under the pressure and friction between the two th-reads. The liquid plastic material and hardener will mix lea-ding to a chemical reaction which will harden the glue, thus giving the required thread locking.

The setting of the mixture will start after 10-15 minutes. Sufficient hardness is achieved after about 30 minutes but complete setting is reached after 24 hours.

Adjustment and setting process must be completed within about 5 minutes.

The thread locking can be cracked by applying the MOUT torque on the thread or alternatively by heating the com-ponent over +170 °C. It is not recommended to re-use the thread.

Description

- Thread locking to the highest order to prevent the self loosening and component loss even under vibration. Not suitable for adjustable bolts or screws.

- This security aspect may be essential for certain applica-tions of standard parts. Stockholding of liquid glue is eli-minated.

- Low insertion torque

- Temperature resistant from – 40 °C up to 170 °C

- Excellent chemical stability

Threads, free from oil and grease give increased strength of locking action.

Components treated with this process can be stored for up to 4 years.

The torque value comply with DIN 267 Part 27. They are based on a test of a thread without preload with a nut thread of 6H at room temperature. For thread lengths l0 < l2, l2 is reduced in such a way that one to two thread turns are not coated at the end of the thread.

|Thread locking Page 1499

Precote 5 is a non-reactive, film-forming emulsion with mineral solids for coating threaded parts.

The coating generates a seal against gases and liquids in threaded parts, both in cylindrical / cylindrical and in cylind-rical / conical pairs. Corrosion in the threaded connection is prevented.

The coating is solvent-free, dry and non-sticky. It is non-ha-zardous for health.

The minimum storage stability in unmounted state is 4 years.

FeaturesDescription

- The sealing coat is a captive element of the locking screw. It saves storing and mounting locking materials.

- The sealing effect sets in after mounting, no curing time is required.

- The friction rating of the thread remains virtually constant, the working-loose torque is low, max. reusable once.

- Sealing effect of thread: cylindrical / cylindrical < 15 bar cylindrical / conical > 50 bar

- Temperature resistance: from – 50 ºC to 180 ºC

- Good chemical resistance, e.g. against oils, water, petrol and solvents

GPC Tightening with thread coatingPrecote 5 (white)

| Alphabetical product index

Alphabetical product index |

Table of contents Alphabetical product indexA-Z


A → PageAdapter, for panel support clamp GN 649, GN 649.1 1275

Adapter bushings, for position indicators GN 952.1 306

Adhesive discs, for retaining magnets, Steel GN 70.1 1415

Adjustable hand levers, Hygienic Design, St. Steel GN 305 326/327

Adjustable hand levers, with push button GN 303 328/329

Adjustable hand levers, with push button GN 303.1 330/331

Adjustable hand levers, with releasing button GN 603 342/343

Adjustable hand levers, with releasing button GN 603.1 344/345

Adjustable knobs, with stepless positioning GN 700 276

Adjustable levers see also:

Adjustable hand levers

Ball handles

Clamping levers

Flat tension levers

Hand levers

Ratchet spanners

Adjustable slide units GN 900 1314

Adjustable tension levers, St. Steel GN 212.5 348/349

Adjustable tension levers, Steel GN 212.3 346/347

Adjustment plates, for bull´s eye levels GN 2277, GN 2277.1 246

Angled ball joints, St. Steel DIN 71802 1167

Angled ball joints, Steel DIN 71802 1166

Angle connector clamps, Aluminum GN 196 1215

Angle pieces, for profile systems, Steel GN 967 1272

Angle pieces, for profile systems 30/40, Aluminum GN 961 1267

Angle pieces, for profile systems 30/40/45, Aluminum GN 960 1268

Arch handles, Aluminum GN 565.4 118

Arch handles, Aluminum GN 665 119

Arch handles, St. Steel GN 424.5 120

Arch handles, St. Steel GN 565.9 118

Arch handles, Steel GN 424.1 120

Assembly pins, St. Steel 2342 760

Assembly sets, for profile systems 30/40 GN 965 1428

Assembly sets, for profile systems 30/40/45 GN 968 1438

Assembly tools, for levelling elements GN 355.1 855

ATEX-Breather caps, with/without dipstick GN 552.6 1126

ATEX-Sight glasses, Aluminum/ESG-glass GN 743.6 1099

Attachment clamp mountings, Aluminum GN 478 1252

Attachment clamp mountings, Aluminum GN 484 1259

B → PageBall buttons, for spring plungers GN 249 728

Ball buttons, for spring plungers GN 250 729

Ball chains, with two key rings GN 111 876

Ball chains, with two key rings, St. Steel GN 111.5 876

Ball handles, with removable cap, Plastic, SOFTLINE GN 675.1 56

Ball handles, with threaded stud, Plastic, SOFTLINE GN 675 57

Ball handles, without removable cap, Plastic, SOFTLINE GN 675 56

Ball joint heads, with female thread GN 648.1 1154

Ball joint heads, with female thread, St. Steel GN 648.5 1156

Ball joint heads, with threaded bolt GN 648.2 1155

Ball joint heads, with threaded bolt, St. Steel GN 648.6 1157

Ball joint thrust pads GN 346 799

Ball jointed levelling feet, Plastic/St. Steel GN 638 1030

Ball jointed levelling feet, Plastic/Steel GN 638 1030

Ball joints GN 648.8 1158

Ball joints, St. Steel GN 648.9 1159

Ball joints, Steel GN 782 1170

Ball knobs, Plastic DIN 319 46

Ball knobs, press on type, Plastic DIN 319 48

Ball knobs, revolving, Plastic GN 319.2 38

Ball knobs, revolving, Plastic, bolt St. Steel GN 319.5 38

Ball knobs, St. Steel DIN 319 47

Ball knobs, Steel, Aluminum DIN 319 47

Ball levers, adjustable, Steel GN 6337.3 359

Ball levers, Steel DIN 6337 366

Ball lock pins, self-locking, St. Steel GN 113.3 748




Ball lock pins, with clamping length compensation GN 113.1 758

Ball lock pins, with T-Handle, St. Steel GN 113.7 750

Ball lock pins, with T-Handle, St. Steel GN 113.8 750

Ball point screws, St. Steel GN 605 783

Ball point screws, St. Steel GN 606 785

Ball point screws, Steel GN 605 783

Ball point screws, Steel GN 606 784

Ball transfer units, housing heavy duty, St. Steel GN 509.1 1370

Ball transfer units, housing heavy duty, Steel GN 509.1 1370

Ball transfer units, housing heavy duty, Steel GN 509.4 1371

Ball transfer units, housing St. Steel GN 509 1368

Ball transfer units, housing Steel GN 509 1368

Base plate clamp mountings, Aluminum GN 473 1246

Base plate connector clamps, Aluminum GN 162 1200

Base plate connector clamps, Aluminum GN 163 1202

Base plate connector clamps, Aluminum/St. Steel GN 162.3 1201

Base plate connector clamps, split assembly, Aluminum GN 165 1204

Base plate connector clamps, split assembly, Aluminum GN 166 1205

Base plate connector clamps, St. Steel GN 162 1200

Base plate connector clamps, St. Steel GN 163.5 1203

Base plates, for knee lever modules GN 910.9 513

Bevel gear wheels, for linear actuators GN 297 1353

Bezel discs, St. Steel GN 185 815

Blanking plugs, St. Steel GN 252.5 791

Blanking plugs, Steel GN 252 791

Bracket / double post bracket accessories GN 868.1 603

Breather caps, with/without dipstick, ATEX GN 552.6 1126

Breather caps, with/without dipstick GN 552 1124

Breather filters, Brass GN 882 1129

Breather filters, Brass GN 884 1130

Breather strainers, Aluminum GN 7403 1131

Breather strainers, St. Steel GN 7403 1131

Breather valves, Brass GN 881 1127

Breather valves, Brass GN 883 1128

Buffers, St. Steel/Rubber GN 254 1085

Alphabetical product index





Buffers, Steel/Rubber GN 253 1084




Buffers see also: Rubber buffers

Silicone buffers

Bull´s eye levels, adjustable GN 2280 249

Bull´s eye levels, for insertion into bore holes GN 2278 247

Bull´s eye levels, for installation GN 2281 250

Bull´s eye levels, for surface mounting GN 2279 248

Bull´s eye levels, with mounting flange GN 2277 244

Bushings, for knee lever modules GN 910.8 513

Button-type magnets, rod-shaped, with bore GN 60 1404

Button-type magnets, with bore GN 60 1404

C → PageC-Clamps, Steel GN 855 570

C-Washers, Steel GN 183 829

Cabinet „U“ handles, Aluminum GN 425 102






Cabinet „U“ handles, Aluminum GN 565.1 81

Cabinet „U“ handles, Aluminum GN 565.3 93


Cabinet „U“ handles, Cast Steel GN 225 97

Cabinet „U“ handles, cranked, Aluminum GN 426.1 114

Cabinet „U“ handles, cranked, Alumimium, St. Steel GN 425.1 107

Cabinet „U“ handles, cranked, St. Steel GN 426.6 115

Cabinet „U“ handles, cranked, Steel GN 425.1 106

Cabinet „U“ handles, Hygienic Design, St. Steel GN 429 110

Cabinet „U“ handles, inclined, Aluminum GN 565.2 86

Cabinet „U“ handles, inclined, St. Steel GN 565.7 87

Cabinet „U“ handles, flat, Aluminum GN 668 95

Cabinet „U“ handles, for welding, Steel GN 426.3 111

Cabinet „U“ handles, Plastic GN 528 90

Cabinet „U“ handles, Plastic GN 528.1 91


Cabinet „U“ handles, Plastic GN 725 84


Cabinet „U“ handles, Plastic with Aluminum/St. Steel tube GN 667 140

Cabinet „U“ handles, Plastic with Aluminum tube GN 667.2 141

Cabinet „U“ handles, Plastic with St. Steel tube GN 667.2 141

Cabinet „U“ handles, Plastic, CLEANLINE GN 625 89

Cabinet „U“ handles, Plastic, ERGOSTYLE® GN 628 96

Cabinet „U“ handles, Plastic, ERGOSTYLE® GN 630.1 88

Cabinet „U“ handles, St. Steel GN 425 103

Cabinet „U“ handles, St. Steel GN 425.3 104





Cabinet „U“ handles, Steel GN 425 102

Cabinet „U“ handles, Steel GN 425.3 104

Cabinet „U“ handles, Steel, Polyurethane foam rubber GN 564 83

Cabinet „U“ handles, Steel with Plastic insulation GN 425.7 105

Cabinet „U“ handles see also:

Arch handles

Finger handles

Folding handles

Gripping trays

Tubular handles

Cables with connector coupling GN 330 1004

Cam action indexing plungers, for welding, Steel GN 612.3 716

Cam action indexing plunger, plunger pin protruded GN 712 706

Cam action indexing plunger, plunger pin retracted GN 712.1 707

Cam action indexing plungers, St. Steel GN 612 704

Cam action indexing plungers, Steel GN 612 704

Cam action indexing plungers, with 180° limit stop, St. Steel GN 721.5 709

Cam action indexing plungers, with 180° limit stop, St. Steel GN 721.6 709

Cam action indexing plungers, with 180° limit stop, Steel GN 721 708

Cam action indexing plungers, with 180° limit stop, Steel GN 721.1 708

Cam action indexing plungers, with screw-on flange, Steel GN 612.2 710

Cam action indexing plungers, Zinc die casting GN 612.9 711

Cam action indexing plungers, Zinc die casting GN 612.10 715

Cam action indexing plungers, Zinc die casting, Steel GN 612.8 705

Cam action indexing plungers see also:

Spring latches

Cam latches GN 218 927

Cam point levers GN 418.1 478

Cam point screws GN 418.2 476

Cam roller carriages, for cam roller linear guide rails GN 2424 1302

Cam roller linear guide rails, C-Profil GN 2422 1301

Cam rollers, for cam roller linear guide rails, GN 2426 1304

Captive C-Washers, Steel DIN 6371 828

Centring bore clamps GN 411.2 488

Centering guide bushing accessories GN 870 610

Clamp mountings, Aluminum GN 477 1247

Clamp mounting bracket accessories GN 873 608

Clamp mounting bracket accessories see also:

Attachment clamp mountings

Base plate clamp mountings

Flanged bolts

Swivel clamp connector bases

T-Clamp mountings

T-Swivel clamp connector bases

Two-way clamp mountings

Clamp mounts, for toggle clamps GN 801 590

Clamp mounts, for toggle clamps GN 809 591

Clamp nuts, Cast Steel GN 206 370



Clamping plates, for position indicators GN 954.6 308

Collar bushings, for scale set GN 268 256

Concial handles, fixed, Plastic GN 203 42

Connecting sets X-Y, for adjustable slide units GN 900, GN 900.2 1317

Connecting sets X-Z, for adjustable slide units GN 900, GN 900.3 1318

Connector clamps see also:

Angle connector clamps

Base plate connector clamps

Flanged connector clamps

Flanged two-way connector clamps

Swivel clamp connector joints

Swivel clamp connector bases

T-angle

T-Base plate connector clamps

Tube connector joints

Tube supports

Two-way clamp mountings

Connector pieces, for oil drain valves GN 880, GN 880.1 1121

Construction tubes, Steel, St. Steel, Aluminum GN 990 1277

Construction tubes see also:

Connector clamps

Control handles, Zinc die casting GN 112.1 226

Control handwheels, Aluminum GN 736 212

Control handwheels, Aluminum GN 736.1 213

Control handwheels, Plastic GN 735 214

Control knobs, for position indicators, Aluminum GN 957 307

Control knobs, Aluminum, anodized, natural color GN 723.4 268

Control knobs, Aluminum, anodized, black GN 726 259

Control knobs, Aluminum, anodized, black GN 726.1 260

Control knobs, Aluminum, anodized, black GN 729 269

Control knobs, Aluminum, anodized, black with scale GN 726.2 261

Control knobs, Plastic GN 526 257

Control knobs, St. Steel GN 436 262

Control knobs, St. Steel GN 436.1 263

Control knobs, with adjustable spindle GN 727 270

Control levers, Steel GN 211 383



Countersunk washers, St. Steel GN 184.5 815

Countersunk washers, Steel GN 184 814

Coupling attachments, for safety handwheels GN 000.4 206

Coupling attachments, for safety handwheels GN 000.5 207

Cover caps, for angle pieces GN 960 / GN 961, GN 963 1269

Cover discs, for knurled handwheels GN 226.1 216

Cranked handles, Aluminum GN 471 220

Cranked handles, Cast iron DIN 468 222

Cranked handles, Cast iron DIN 469 223

Cranked handles, Plastic GN 570.2 221

Cranked handles, St. Steel GN 269 224

Cranked handles, Zinc die casting GN 471.1 220


Clamp nuts, double lever, Cast Steel GN 206.1 371

Clamp nuts, double lever, St. Steel GN 99.8 369

Clamp nuts, double lever, St. Steel precision casting GN 206.1 371

Clamp nuts, double lever, Steel GN 99.7 369

Clamp nuts, St. Steel GN 99.6 368

Clamp nuts, St. Steel precision casting GN 206 370

Clamp nuts, Steel GN 99.5 368

Clamping arm extenders, for knee lever modules GN 910.7 513

Clamping bolts, St. Steel GN 918.6 474

Clamping bolts, St. Steel GN 918.7 475

Clamping bolts, Steel GN 918.1 474

Clamping bolts, Steel GN 918.2 475

Clamping elements, for adjustable spindles GN 826 268

Clamping indexing plungers, with safety function GN 7336.8 693

Clamping kits, for clamp mountings GN 511 1260

Clamping kits, for clamp mountings GN 511.1 1261

Clamping kits, for connector clamps GN 911 1242

Clamping kits, for connector clamps, St. Steel GN 911.3 1242

Clamping knobs, with indexing plungers GN 7336.7 692

Clamping levers, adjustable, increased clamping force GN 300.4 332 ff.

Clamping levers, adjustable, Plastic, ERGOSTYLE® GN 604 338 ff.

Clamping levers, adjustable, Plastic/St. Steel GN 604.1 340 ff.

Clamping levers, adjustable, St. Steel electropolished GN 300.6 324 ff.

Clamping levers, adjustable, St. Steel GN 300.5 324 ff.

Clamping levers, adjustable, Steel GN 99.2 356

Clamping levers, adjustable, Steel GN 6337.3 358

Clamping levers, adjustable, straight, Zinc die casting GN 302 334 ff.

Clamping levers, adjustable, with push-button GN 303 328 ff.

Clamping levers, adjustable, with push-button GN 603.1 344 ff.

Clamping levers, adjustable, with releasing button, Plastic GN 603 342 ff.

Clamping levers, adjustable, with special tipped GN 306 320

Clamping levers, adjustable, Zinc die casting GN 101 336 ff.

Clamping levers, adjustable, Zinc die casting GN 300 318 ff.

Clamping levers, adjustable, Zinc die casting/St. Steel GN 300.1 322 ff.

Clamping levers, fixed, Plastic, ERGOSTYLE® GN 601 367

Clamping levers, lever Steel GN 927.3 468

Clamping levers, lever Zinc die casting GN 927 468

Clamping levers, lever Zinc die casting/St. Steel GN 927.4 470

Clamping levers, short, Steel GN 204 365

Clamping levers, St. Steel DIN 99 364

Clamping levers, St. Steel GN 927.5 470

Clamping levers, St. Steel GN 927.7 471

Clamping levers, Steel, DIN 99 364

Clamping pads, St. Steel, adjustable GN 709.35 846

Clamping pads, St. Steel, with female thread GN 709.25 845

Clamping pads, St. Steel, with threaded stud GN 709.15 844

Clamping pads, Steel, adjustable GN 709.3 846

Clamping pads, Steel, adjustable GN 709.6 847

Clamping pads, Steel, threaded bolt with internal hexagon GN 709.8 849

Clamping pads, Steel, with internal hexagon GN 709.2 845

Clamping pads, Steel, with internal hexagon GN 709.7 848

Clamping pads, Steel, with threaded stud GN 709.1 844

Clamping plates, for position indicators GN 953.6 308


Cranked handles see also: Control handles

Cranks

Indexing cranked handles

Retractable cranked handles

Tri-ball handles

Cranked handles with retractable handle, Aluminum GN 471.3 228



Cranks, Steel GN 369 225

Cylinder head shoulder bolts, Steel GN 732 787

Cylindrical handles, Plastic GN 519 52

Cylindrical handles, Plastic, SOFTLINE GN 519.6 54

Cylindrical handles, press on type, Plastic GN 519.1 32

D → PageDisc handwheels, Aluminum DIN 3670 189

Disc handwheels, Aluminum GN 321 188



Disc handwheels, for linear actuators Ø 18 GN 923.18 1348

Disc handwheels, for linear actuators Ø 30, 30 GN 923.30 1348




Disc handwheels, for linear actuators Ø 60 GN 924.60 1349

Disc handwheels, for position indicators, Aluminum GN 323.8 284

Disc handwheels, for position indicators, Aluminum GN 323.9 292

Disc handwheels, bushing St. Steel, Plastic GN 520.2 193

Disc handwheels, bushing Steel, Plastic GN 520.1 192

Disc handwheels, Plastic GN 521 190

Disc handwheels, Plastic, with St. Steel bushing GN 521.5 191

Discs, Aluminum GN 745.1 1111

Discs, Aluminum, with drain symbol GN 740.1 1111

Discs, Aluminum, with re-fill symbol GN 747.1 1111

Discs, Steel, with cover cap GN 338 817

Distance bushings, for cabinet „U“ handles, GN 628.2 96

Distance bushings, St. Steel GN 609.5 694

Domed gear knobs, press on type, Plastic, CLEANLINE GN 719.2 49

Double cam levers, St. Steel GN 917.1 481

Double cam levers, Steel GN 917 481

Double hinges, for profile systems, Plastic GN 159.1 970

Double ring spanner, GN 607.9 662

Double tube linear actuators, for double slider GN 492 1364

Double tube linear actuators, for single slider GN 491 1360

Drive, for linear actuators GN 391 1352

Dust caps, for angled ball joints GN 710 1169

E → PageEccentric bushings, for side thrust pins GN 715.2 745

Eccentrical cams, St. Steel, downward axial GN 918.7 475

Eccentrical cams, St. Steel, radial GN 918.5 472

Eccentrical cams, St. Steel, upward axial GN 918.6 474


Eccentrical cams, Steel, downward axial GN 918.2 475

Eccentrical cams, Steel, radial GN 918 472

Eccentrical cams, Steel, upward axial GN 918.1 474

Edge handles, Aluminum tube GN 481 154

Edge protection profiles GN 2184 954

Edge protection seal profiles GN 2180 948

Edge protection seal profiles GN 2182 950

Elliptical shaped knobs, Plastic GN 201 51

F → PageFastening units, for the adjustable slide units GN 900, GN 900.1 1316

Fastening sets, for cabinet „U“ handles GN 181 116

Feet DIN 6320 841

Feet see also:

Ball jointed levelling feet

Levelling feet

Finger handles, St. Steel GN 224.5 121

Finger handles, Steel GN 224.1 121

Fixed handles, fix, Steel, St. Steel, Plastic DIN 39 41

Flanged bolts, for clamp mountings, Steel GN 480 1253

Flanged connector clamps, Aluminum GN 145 1195

Flanged connector clamps, Aluminum, GN 146 1196

Flanged connector clamps, Aluminum, GN 146.3 1196

Flanged connector clamps, split assembly, Aluminum GN 147 1198

Flanged connector clamps, split assembly, Aluminum GN 147.3 1199

Flanged connector clamps, St. Steel GN 145 1195

Flanged connector clamps, St. Steel GN 146.6 1197

Flanged connector clamps, St. Steel GN 146.5 1197

Flanged two-way connector clamps, multi part assembly GN 141 1194

Flanges, for swivel ball joints GN 784, GN 784.1 1266

Flat adjustable hand levers, Zinc die casting GN 302 334/335

Flat springs, for scale set GN 374 256

Folding handles, Plastic GN 825.1 128

Folding handles, St. Steel GN 425.2 122

Folding handles, St. Steel GN 425.5 123

Folding handles, Steel GN 425.2 122

Folding handles, Steel GN 425.5 123

Folding handles with recessed tray, Plastic GN 825.2 126

Folding handles with recessed tray, St. Steel GN 425.8 124

Folding handles with recessed tray, Steel GN 425.8 124

Foot plates, Steel, for grub screws DIN 6332, GN 6311.3 796

Fork heads, Aluminum GN 71752 1163

Fork heads, St. Steel DIN 71752 1162

Fork heads, Steel DIN 71752 1160

Fork joints, Aluminum GN 751 1163

Fork joints, St. Steel GN 751 1162

Fork joints, Steel GN 751 1160

Fork joints, with rotating shaft, Steel GN 751.1 1164

G → PageGaiters, for universal joints GN 808.1 1151

Gaskets, for threaded plugs, Aluminum/Copper DIN 7603 1118

Gear levers, Plastic, ERGOSTYLE® GN 623 380


Gear levers, Plastic, ERGOSTYLE®, with St. Steel bushing GN 623.5 380

Gear lever handles, St. Steel GN 310 65

Gear lever handles, Steel GN 310 65

Gripping trays, ERGOSTYLE®, Plastic GN 731 162

Gripping trays, Plastic GN 731.1 164

Grub screws, with ball pin, St. Steel GN 632.5 797

Grub screws, with ball pin, Steel GN 632.1 797

Grub screws, with brass/plastic pivot, St. Steel GN 913.5 779

Grub screws, with brass/plastic pivot, Steel GN 913.3 778

Grub screws, with hardened pivot, Steel GN 913.2 780

Grub screws, with retaining magnet, Steel GN 913.6 1409

Grub screws, with thrust point, Steel DIN 6332 793

Guide bushings, with collar, conical GN 172.1 683

Guide bushings, with collar, cylindrical DIN 172 830

Guide bushings, without collar, conical GN 179.1 683

Guide bushings, without collar, cylindrical DIN 179 830

Guide pins GN 771.1 832

Guide pots, for serrated locking plates GN 187.1 826

Guide rollers GN 753 1373

H → PageHand knobs, Aluminum DIN 6335 420

Hand knobs, Cast iron DIN 6335 420

Hand knobs, Plastic DIN 6335 422

Hand knobs, St. Steel DIN 6335 420

Hand knobs, St. Steel GN 6335.5 421

Hand knobs, St. Steel threaded stud, Aluminum GN 6335.5 421

Hand knobs, St. Steel threaded stud, Plastic GN 6335.5 423

Hand knobs, Steel threaded stud, Cast iron GN 6335.4 421

Hand knobs, Steel threaded stud, Plastic GN 6335.4 423

Hand knobs, with increased clamping force, Plastic GN 6335.9 426

Hand knobs, with protruding St. Steel bushing GN 6335.2 424

Hand knobs, with protruding Steel bushing GN 6335.1 424

Hand knobs, with protruding Steel bushing GN 6335.2 424

Handle shanks, for tubular handles GN 333.8 135

Handle shanks, for tubular handles GN 333.9 135

Handle tubes, with screw channel, Aluminum GN 930 153

Handles, for knee lever modules GN 910.5 513

Handwheels, Cast iron, Aluminum DIN 950 181

Handwheels, for valves, pressed Steel GN 227 219

Handwheels, Plastic GN 527.1 218

Handwheels, pressed Steel GN 227.1 185

Handwheels, St. Steel GN 949 183

Handwheels, St. Steel GN 950.6 182

Handwheels, St. Steel pressed A2 GN 227.2 184

Handwheels, St. Steel pressed A4 GN 227.4 184

Handwheels, with large hub, Cast iron GN 950.1 181

Handwheels see also:

Control handwheels

Disc handwheels

Handwheels with retractable handle

Knurled handwheels

Saftey handwheels

Spoked handwheels

Handwheels with retractable handle, Aluminum GN 322.3 198






Handwheels with retractable handle, Plastic GN 521.3 194

Handwheels with retractable handle, Plastic GN 522.3 200

Handwheels with retractable handle, Plastic/St. Steel GN 521.6 195

Handwheels with retractable handle, Plastic/St. Steel GN 522.6 201

Headed dowels DIN 6321 834

Headed dowels GN 6321.1 840

Hexagon head screws, with brass/plastic pivot, St. Steel DIN 933.5 781

Hexagon nuts, for Indexing plungers, Steel GN 909 695

Hexagon nuts, St. Steel, for Indexing plungers GN 909.5 695

Hexagon nuts, with ball socket GN 347 800

Hexagon nuts, with collar, Steel DIN 6331 808

Hexagon nuts, with spherical seating DIN 6330 807

Hinge, without switch, Plastic GN 239.7 998

Hinge, without switch, St. Steel GN 139.6 996

Hinge, without switch, Zinc die casting GN 139.6 996

Hinges, adjustable by slotted holes, Plastic GN 151.4 981

Hinges, adjustable, with cover, Zinc die casting GN 238 978

Hinges, adjustable, Zinc die casting GN 127 980

Hinges, Aluminum GN 237 959

Hinges, Aluminum, for welding GN 128.2 991

Hinges, detachable, St. Steel GN 337 986

Hinges, detachable, Zinc die casting GN 337 986

Hinges, for profile systems, Plastic GN 159 968

Hinges, for profile systems, Zinc die casting GN 161 972

Hinges, for welding, detachable, Steel GN 128 990

Hinges, Plastic GN 151 967

Hinges, Plastic GN 159.1 970



Hinges, Plastic, with electrical switching function GN 239.4 1002

Hinges, Plastic, without switch GN 239.3 1002

Hinges, St. Steel GN 237 959

Hinges, St. Steel, extended hinge wings GN 237 963

Hinges, St. Steel, for welding GN 128.2 991

Hinges, St. Steel, three parts GN 129.2 976

Hinges, St. Steel, three parts GN 129.5 975

Hinges, St. Steel precision casting GN 139.6 996

Hinges, Steel, three parts GN 129.2 976

Hinges, Steel, three parts GN 129.3 977

Hinges, Steel, two or three parts GN 129 974

Hinges, with adjustable friction, Plastic GN 233 382

Hinges, Zinc die casting GN 138 966

Hinges, Zinc die casting GN 139.2 992

Hinges, Zinc die casting GN 237 959

Hinges, Zinc die casting, detachable GN 161.1 988

Hinges, Zinc die casting, detachable GN 161.2 989



Hinges, Zinc die casting, extended hinge wings GN 237 963

Hinges, Zinc die casting, with with adjustable friction GN 437 982

Hinges with safety switch, Plastic GN 239.6 998

Hinges with safety switch, St. Steel GN 139.5 996

Hinges with safety switch, Zinc die casting GN 139.1 992

Holder, for spring plungers GN 614.1 738

Holding bushings, for lifting pins GN 1130, GN 1132 1079

Holding discs, for retaining magnets, Steel/St. Steel GN 70 1414

Hook-type latches, lockable GN 115.8 933

Hook-type latches, with operating elements GN 115.8 930

Hook-type latches, with key GN 115.8 932

Hook-type toggle clamps, Steel GN 850 540

Hook wrenches with nose end, for slotted nuts GN 1810 801

Horizontal acting toggle clamps, St. Steel GN 820 520

Horizontal acting toggle clamps, St. Steel GN 820.1 522

Horizontal acting toggle clamps, St. Steel GN 820.2 528

Horizontal acting toggle clamps, Steel GN 820 520

Horizontal acting toggle clamps, Steel GN 820.1 522

Horizontal acting toggle clamps, Steel GN 820.2 528

Horizontal acting toggle clamps, Steel/St. Steel GN 820.3 528

Horizontal acting toggle clamps, Steel/St. Steel GN 820.4 526

Horizontal latch type toggle clamps, St. Steel GN 851 542

Horizontal latch type toggle clamps, Steel GN 851.3 544

Hose adapters, barbed fitting, St. Steel GN 480.7 1254

Housings, for angular / T-gears GN 298 1354

Hubs with eccentrical cam GN 919 480

Hygienic latches, St. Steel, with socket GN 115 903

I → PageIndexing cranked handles GN 558 231

Indexing levers GN 215 278

Indexing mechanisms, St. Steel GN 200 274

Indexing mechanisms, Steel GN 200 272

Indexing plungers, for precision locating GN 817.3 680

Indexing plungers, for precision locating GN 817.5 681

Indexing plungers, for thin walled equipment GN 607.2 662

Indexing plungers, for thin walled equipment GN 607.3 663

Indexing plungers, for welding GN 607.4 664

Indexing plungers, removable, with/without rest position GN 817.8 651

Indexing plungers, removable, with/without rest position GN 817.9 655

Indexing plungers, with long knob, St. Steel GN 817.2 652

Indexing plungers, with long knob, Steel GN 817.2 652

Indexing plungers, with rest position, for welding GN 607.5 665

Indexing plungers, with rest position, St. Steel GN 607.1 661



Indexing plungers, with rest position, Steel GN 607.1 661



Indexing plungers, with safety lock, St. Steel GN 414 684

Indexing plungers, with safety lock, Steel GN 414 684

Indexing plungers, with safety lock, with rest position GN 414.1 685

Indexing plungers, with screw-on flange GN 412 674

Indexing plungers, with screw-on flange GN 817.1 854

Indexing plungers, with screw-on flange, St. Steel GN 412 674

Indexing plungers, with screw-on flange, St. Steel GN 417 678 ff.

Indexing plungers, with screw-on flange, St. Steel GN 608.5 666

Indexing plungers, with screw-on flange, Steel GN 608 666

Indexing plungers, with T-Handle, Steel/St. Steel GN 817.4 653

Indexing plungers, with/without rest position, St. Steel GN 413 659

Indexing plungers, with/without rest position, St. Steel GN 717 656 ff.



Indexing plungers, with/without rest position, Steel GN 413 659

Indexing plungers, with/without rest position, Steel GN 717 656 ff.



Indexing plungers, without rest position, St. Steel GN 607 660



Indexing plungers, without rest position, Steel GN 607 660



Indexing plungers, without thread GN 618 649

Indexing plungers see also:

Clamping indexing plungers

Clamping knobs with indexing plunger

Mini indexing plungers

Locking plungers

Spring bolts

Spring latches

Installation brackets GN 970 1270/1271

Indicator arrows for rulers GN 711.1 240

Indicator arrows for rulers GN 711.3 241

Installation kits, for position indicators GN 295 1350

Installation kits, for position indicators GN 296 1351

Installation kits, for position indicators GN 491.1 1367

Insert bushings, for construction tubes GN 992 1059

Insert bushings, for profiled square tubes, Plastic GN 348.1 1058

Insert bushings, St. Steel GN 992.5 1059

Installation kits, for position indicators GN 491.1 1367

J → PageJaw block accessories, for pneumatic fastening clamps GN 872 606

Joint pieces, for fork joints, St. Steel GN 752 1165

Joint pieces, for fork joints, Steel GN 752 1165

Joints see also:

Angled ball joints

Ball joint heads

Ball joints

Ball jointed levelling feet

Fork joints

Swivel clamp connector joints

Universal joint shafts with friction bearing

Universal joints



K → PageKey rings, for ball chains und retaining cables GN 111.3 876

Keys, for latches GN 119.2 940

Keys, St. Steel DIN 6885 843

Keys, Steel DIN 6885 842

Knee lever modules, for mounting GN 910.2 510

Knee lever modules, for welding GN 910.3 512

Knobs, St. Steel GN 676.5 64

Knobs, Steel GN 676.1 64

Knobs see also:

Ball handles

Cylindrical handles

Domed gear knobs

Elliptical shaped knobs

Knurled knobs

Mushroom type knobs

Tapered knobs

Knurled handwheels, Plastic GN 226 216

Knurled knobs, Plastic GN 534 442

Knurled knobs, Plastic GN 676 62/63

Knurled knobs, Plastic GN 7336 444

Knurled knobs, Plastic, ERGOSTYLE® GN 676 62

Knurled nuts, flat type, St. Steel DIN 467 458

Knurled nuts, flat type, Steel DIN 467 458

Knurled nuts, St. Steel DIN 6303 454

Knurled nuts, St. Steel DIN 466 456

Knurled nuts, St. Steel GN 536 452

Knurled nuts, St. Steel bushing, Plastic GN 420 448

Knurled nuts, Steel DIN 466 456

Knurled nuts, Steel DIN 6303 454

Knurled nuts, Steel bushing, Plastic GN 420 448

Knurled nuts see also:

Knurled knobs

Torque limiting knobs

Knurled screws, flate type, St. Steel DIN 653 459

Knurled screws, flate type, Steel DIN 653 459

Knurled screws, Plastic GN 534 443

Knurled screws, Plastic GN 7336 444

Knurled screws, Plastic, ERGOSTYLE® GN 676 63

Knurled screws, Plastic, with Brass/Plastic pivot GN 7336.5 445

Knurled screws, St. Steel DIN 464 457

Knurled screws, St. Steel GN 535 452

Knurled screws, Steel DIN 464 457

Knurled screws, with ball pin, Plastic GN 421.11 451

Knurled screws, with Brass/Plastic pivot, Plastic GN 421.10 450

Knurled screws, with movable thrust pad, Plastic GN 421.12 451

Knurled screws, with movable thrust pad, Plastic GN 421.12 451

Knurled screws, with recessed stud, Steel/St. Steel GN 653.2 461

Knurled screws, with Brass/Plastic pivot, Steel/St. Steel GN 653.10 460

Knurled screws see also:

Knurled knobs

Knurled knob screws

Knurled knobs with threaded stud

Knurled thumb screws, St. Steel stud, Plastic GN 421 449

Knurled thumb screws, Steel stud, Plastic GN 421 449

L → PageLatch-Type toggle clamps, heavy duty, St. Steel GN 852 552

Latch-Type toggle clamps, heavy duty, Steel GN 852 550

Latch-Type toggle clamps, heavy duty, Steel GN 852.3 554/556

Latch-Type toggle clamps, Steel/St. Steel GN 851 542

Latch-Type toggle clamps, Steel/St. Steel GN 851.1 546

Latch-Type toggle clamps, Steel GN 851.2 548

Latch-Type toggle clamps, with locking mechanism, St. Steel GN 853 564

Latch-Type toggle clamps, with locking mechanism, Steel GN 853 562

Latch-Type toggle clamps, with locking mechanism, Steel GN 858 566

Latch-Type toggle clamps, with trigger function, Steel GN 854 568

Latches, lockable GN 115 899

Latches, for snap-in mounting, Plastic GN 115.3 908

Latches, Plastic GN 115.3 906

Latches, St. Steel, lockable GN 115 902

Latches, St. Steel, with key GN 115 901

Latches, St. Steel, with operating elements GN 115 900

Latches, with cabinet „U“ handle GN 115.7 910

Latches, with gripping tray, lockable GN 115.10 914

Latches, with gripping tray, with key GN 115.10 912

Latches, with key GN 115 898

Latches, with operating elements GN 115 896

Latches, with star knob GN 117 922

Latches, with star knob/key GN 119 924

Latches, with star knob/key St. Steel GN 119 926

Latches see also:

Hook-type latches

Hygienic latches

Ledge handles with locking mechanism

Latches with cabinet „U“ handles

Mini latches

Rotary clamping latches

Stop locks

Latches with cabinet „U“ handles, with cam latch GN 119.3 928

Latches with cabinet „U“ handles see also:

Hook-type latches

Hygienic latches

Latches

Ledge handles with locking mechanism

Mini latches

Rotary clamping latches

Snap locks

Stop locks

Ledge handles, Aluminum GN 430 156

Ledge handles, Aluminum GN 730 158

Ledge handles, Plastic, ERGOSTYLE® GN 630 161

Ledge handles, St. Steel GN 730.5 159

Ledge handles, with lettering block, Aluminum GN 430.1 156

Lever arms, for knee lever modules GN 910.6 513

Level markings, for oil dipsticks GN 109 1425



Linear actuator connectors, Aluminum GN 135.1 1343


Linear actuator connectors, base plate, Aluminum GN 162.1 1334



Linear actuator connectors, base plate, St. Steel GN 162.1 1334

Linear actuator connectors, flanged, Aluminum GN 145.1 1332

Linear actuator connectors, flanged, Aluminum GN 146.1 1333

Linear actuator connectors, flanged, St. Steel GN 145.1 1332

Linear actuator connectors, swivel clamp, Aluminum GN 273.1 1338

Linear actuator connectors, swivel clamp, Aluminum GN 274.1 1339

Linear actuator connectors, T-angle, Aluminum GN 191.1 1336

Linear actuator connectors, T-angle, Aluminum GN 192.1 1337

Linear actuator connectors, T-angle, St. Steel GN 191.1 1336

Linear actuator connectors, T-angle, St. Steel GN 192.1 1337

Linear slides, telescopic, dual configuration GN 2410 1295

Linear slides, telescopic, H-shaped rail GN 2408 1294

Linear slides, telescopic, partial extension GN 2404 1292

Linear slides, telescopic, S-shaped GN 2406 1293

Linear slides, with no extension GN 2402 1291

Load rings, for welding, Steel GN 587 1072

Load rings, rotating, Steel GN 586.1 1070

Load rings, Steel GN 5860 1068

Locators, for indexing plungers GN 417, GN 417.1 677

Locators, for spring latches GN 416, GN 416.1 676

Locking pins, with axial lock, St. Steel GN 114.3 753





Locking pins, with axial lock, Steel GN 114.2 752

Locking pins, with axial lock, Steel GN 214.2 754

Locking pins, with axial lock (magnetic) GN 124.1 757

Locking plungers, plunger protruded GN 816 686

Locking plungers, plunger retracted GN 816.1 688

Locking plungers, PUSH-PUSH mechanism GN 514 690

Longitudinal scales, for linear actuators GN 299 1346

Loss protection, for several standard parts GN 111.7 1426

M → PageMagnetic plugs, Aluminum GN 738 1112

Magnetic plugs, Aluminum, with VITON®-Sealing ring GN 738.1 1112

Magnets, disc-shaped, rubber jacket GN 51.7 1407

Magnets, disc-shaped, without bore GN 53.1 1406

Magnets see also:

Button-type magnets

Grub screws with retaining magnet

Setting bolts with retaining magnet

Magnetic plugs

Pot magnets

Raw magnets

Retaining magnets

U-Magnets

Levelling disks, St. Steel GN 6343 811

Levelling elements, Steel/St. Steel GN 355 854

Levelling feet, fixed, Steel/St. Steel GN 339 1032

Levelling feet, Hygienic Design, St. Steel GN 20 1034 ff.

Levelling feet, Plastic/St. Steel GN 344.6 1026

Levelling feet, Plastic/Steel GN 344.1 1026

Levelling feet, St. Steel GN 21 1038

Levelling feet, St. Steel GN 41 1042

Levelling feet, St. Steel, with mounting holes GN 23 1038

Levelling feet, St. Steel, with mounting lug GN 43 1042

Levelling feet, St. Steel, with rubber underlay GN 31 1046

Levelling feet, St. Steel, with rubber underlay, with lug GN 33 1050

Levelling feet, Steel sheet GN 40 1040

Levelling feet, Steel sheet, with mounting lug GN 42 1040

Levelling feet, Steel sheet, with rubber underlay GN 30 1044

Levelling feet, Steel sheet, with rubber underlay, with lug GN 32 1048

Levelling feet, with mounting holes, Plastic/St. Steel GN 345.6 1028

Levelling feet, with mounting holes, Plastic/Steel GN 345.1 1028

Levelling feet, with threaded bushing, Plastic/St. Steel GN 343.7 1020

Levelling feet, with threaded bushing, Plastic/Steel GN 343.3 1016

Levelling feet, with threaded bushing, St. Steel GN 343.5 1018

Levelling feet, with threaded bushing, Steel GN 343.1 1014

Levelling feet, with threaded stud, Plastic/Steel GN 343.4 1016

Levelling feet, with threaded stud, Plastic/St. Steel GN 343.8 1020

Levelling feet, with threaded stud, St. Steel GN 343.6 1018

Levelling feet, with threaded stud, Steel GN 343.2 1014

Levelling feet, with threaded stud, Steel GN 6311.4 1024

Levelling feet, with vibration damping GN 342.1 1022

Levelling feet, with vibration damping GN 342.2 1022

Levelling feet, with vibration damping element GN 148 1052

Levelling sets, long version, St. Steel GN 350 850

Levelling sets, long version, Steel GN 350 850

Levelling sets, short version, St. Steel GN 350.1 851

Levelling sets, short version, Steel GN 350.1 851

Levelling sets, with spherical washer, St. Steel GN 350.2 852

Levelling sets, with spherical washer, St. Steel GN 350.5 853

Levelling sets, with spherical washer, Steel GN 350.2 852

Levelling sets, with spherical washer, Steel GN 350.5 853

Lifting eye bolts, rotating, St. Steel GN 581.5 1064

Lifting eye bolts, rotating, Steel GN 581 1062

Lifting eye bolts, Steel/St. Steel DIN 580 1060

Lifting eye nuts, rotating, Steel GN 583 1066

Lifting eye nuts, Steel, St. Steel DIN 582 1061

Lifting pins, Steel/St. Steel GN 1130 1078

Lifting points, for welding, Steel GN 589 1074

Linear actuators, GN 291 1226










Plugs, with/without dipstick, Plastic GN 548.1 1120

Pneumatic fastening clamps GN 864 594



Pneumatic push-pull toggle clamps GN 890 582

Pneumatic toggle clamps GN 860 572

Pneumatic toggle clamps, heavy-duty GN 861 574

Pneumatic toggle clamps, heavy-duty GN 863 563

Pneumatic toggle clamps, with additional manual operation GN 862.1 578

Pneumatic toggle clamps, with vertical mounting base GN 862 576

Position indicators, digital GN 953 296



Position indicators, digital, electronic GN 9053 302

Position indicators, digital, electronic GN 9054 304

Position indicators, pendulum system, analog GN 000.8 283

Position indicators, retaining system, analog GN 000.9 288

Position indicators, retaining system, digital/analog GN 000.13 291

Positioning bushing, for indexing plungers GN 412.2 696

Positioning bushing, with ramping cone GN 412.3 697

Positioning elements, with female thread GN 409.2 837

Positioning elements, with male thread GN 409.1 836

Pot magnets, with bore GN 58 1391

Protective caps, for latches GN 120 942

Protective caps, Rubber GN 806 1089

Protective guide plates, for latches GN 120.2 944

Proximity switch GN 896.1 584



Pull-down plates, for wedge clamps GN 920.2 484

Push-pull type toggle clamps, for push-on clamping GN 841 534

Push-pull type toggle clamps, for push-pull clamping GN 840 530


Push-pull type toggle clamps, for push-pull clamping GN 843.1 538


Q → PageQuick-fit couplings, with off-set compensation GN 240.2 1173

Quick-fit couplings, with radial off-set compensation GN 240 1171

Quick-fit couplings, with radial off-set compensation GN 240.1 1172

Quick release knurled nuts, Steel GN 6303.1 462

Quick release set collars, Aluminum GN 704 863

Quick release star knobs, Plastic GN 6336.3 404

Quick release toggle nuts, Steel GN 6305.1 376

R → PageRatchet spanners GN 316 362

Raw magnets, block-shaped, without bore GN 55.4 1413

Raw magnets, disc-shaped, with bore GN 55.1 1410

Raw magnets, disc-shaped, without bore GN 55.2 1411

Raw magnets, rod-shaped, without bore GN 55.3 1412

Reference flanges, for control knobs GN 723.3 266

Retaining cables GN 111.2 877

Mini-Latches GN 115.1 904

Mini-Latches, St. Steel GN 115.6 904

Mini indexing plungers, with/without rest position GN 822 668

Mini indexing plungers, with/without rest position GN 822.1 668





Mounting blocks, for indexing plungers, St. Steel GN 612.1 699

Mounting blocks, for indexing plungers, Steel GN 612.1 699

Mounting blocks, for indexing plungers, Zinc die casting GN 412.1 698

Mounting nuts, for oil level sight glasses, Brass GN 543.1 1134

Mounting plate, for switch GN 139.3 994

Mounting plate, for switch GN 139.4 994

Mounting plates, for adjustable slide units GN 900, GN 900.4 1320

Mounting plates, for hinges GN 239.8 1000

Mounting tools, for shaft clamping units GN 928.1 486

Mounting tools, for side thrust pins GN 713.1 742

Mounting tools, for side thrust pins GN 715.1 740

Mounts for leveling feet, for levelling feet, Steel GN 349 1056

Mushroom type knobs, Plastic GN 76 58

N → PageNuts, Hygienic Design, St. Steel GN 1580 809

O → PageOil drain valves, Steel/Brass GN 880 1120

Oil level indicators, narrow shape, Plastic GN 650.4 1108

Oil level indicators, Plastic GN 650 1106

Oil level indicators, with protective housing, Plastic GN 650.2 1110

Oil level indicators, with VITON®-Sealing ring, Plastic GN 650.1 1106

Oil level sight glasses, Aluminum/ESG-Glass GN 743.1 1096

Oil level sight glasses, Aluminum/natural Glass GN 743 1096

Oil level sight glasses, Brass/ESG-Glass GN 743.3 1097

Oil level sight glasses, Brass/natural Glass GN 743.2 1097

Oil level sight glasses, crystal-clear Plastic GN 541.1 1102

Oil level sight glasses, crystal-clear Plastic GN 744 1101

Oil level sight glasses, St. Steel/ESG-Glass GN 743.5 1098

Oil level sight glasses, St. Steel/natural Glass GN 743.4 1098

Oil level sight glasses, with conical thread GN 743.7 1100

Oil level sight glasses, with conical thread GN 743.8 1100

Oil level sight glasses, without thread, Aluminum GN 537 1103

Open-end wrenches, for cam roller carriages GN 2424.1 1303

Opening handles, for latches GN 120.1 943

Oval tubular handles, Aluminum GN 366 152

Oval tubular handles, Aluminum/Zinc die casting GN 334 142

Oval tubular handles, Aluminum/Zinc die casting GN 334.1 143

P → PagePanel support clamp, Plastic GN 649 1274

Parallel clamp mountings, Aluminum GN 474.1 1249

Pin keys, for oil level sight glasses GN 537.1 1103

Plates with tapped holes, for hinges, GN 2372 960



Retaining magnets, disc-shaped, rubber jacket GN 51.2 1394



Retaining magnets, disc-shaped, St. Steel GN 50.25 1386

Retaining magnets, disc-shaped, with bore GN 50.4 1388

Retaining magnets, disc-shaped, with bore, St. Steel GN 50.45 1389

Retaining magnets, disc-shaped, with threaded stud GN 50.3 1383

Retaining magnets, disc-shaped, with hook/eyelet GN 50.6 1385

Retaining magnets, disc-shaped, with female thread GN 50.2 1384

Retaining magnets, disc-shaped, with female thread GN 50.5 1390

Retaining magnets, for profile systems, Plastic GN 56 1416

Retaining magnets, rod-shaped, gummed, St. Steel GN 52.5 1403

Retaining magnets, rod-shaped, with female thread GN 52.2 1399

Retaining magnets, rod-shaped, with female thread GN 52.3 1400

Retaining magnets, rod-shaped, with stud/smooth stud GN 52.4 1402

Retaining magnets, with bore, rubber jacket GN 51.4 1393

Retaining magnets, with threaded stud, rubber jacket GN 51.3 1393

Retaining plates, for clamp mountings, St. Steel GN 479.1 1263

Retaining rings GN 111.6 879

Retaining rods, for clamp mountings GN 480.1 1256

Retaining tubes, for clamp mountings GN 480.1 1256

Retaining washers, St. Steel GN 2344 762

Retractable handles, automatic return GN 798.7 45

Retractable handles, Plastic/St. Steel GN 598.5 43

Retractable handles, Plastic/St. Steel GN 798.5 44

Retractable handles, Plastic/Steel GN 598.3 43

Retractable handles, Plastic/Steel GN 798.3 44

Revolving cylindrical handles, Plastic, St. Steel shaft GN 599.5 37

Revolving handles, Plastic, Aluminum GN 798 32

Revolving handles, Plastic, St. Steel shaft GN 598.1 36

Revolving handles, Plastic, St. Steel shaft GN 798.1 33

Revolving handles, Plastic, Steel GN 598 35

Revolving handles, Steel, Aluminum, Plastic DIN 98 40

Revolving handles, Steel spindle with female thread GN 798.2 34

Rhombus T-Nuts, Steel GN 508.1 867

Rotary clamping latches, with knurled knob/socket GN 116.1 916

Rotary clamping latches, with control elements/socket GN 516 918

Rotary clamping latches, with control elements/socket GN 516.1 921

Rotary clamping latches, with control elements/socket GN 516.5 920

Rotary plates, for adjustable slide units GN 900, GN 900.5 1321

Rotary tables GN 900.6 1322

Rubber buffers, St. Steel GN 451 1080

Rubber buffers, St. Steel GN 452 1081

Rubber buffers, Steel GN 351 1080

Rubber buffers, Steel GN 352 1081

Rubber pads, for levelling feet GN 148, GN 148.2 1055

Rubber bumper stops, for hinges GN 2374 962

Rulers GN 711 240

Rulers GN 711.2 241

S → PageSafety handwheels, Aluminum GN 321.4 204/205

Safety handwheels, Aluminum GN 321.5 204/205


Safety handwheels, Aluminum GN 321.6 208





Safety handwheels, Aluminum GN 327 210

Safety retractable handles GN 798.7 45

Safety retractable handles GN 798.8 45

Safety star knobs, Plastic GN 5337.3 410

Safety star knobs, Plastic, lockable GN 5337.9 409

Safety star knobs with threaded stud, Plastic GN 5337.3 410

Safety star knobs with threaded stud, Plastic GN 5337.9 409

Safety tension levers, Steel GN 312 360/361

Scale rings GN 164 253

Scale rings GN 264 255

Scale rings, control knobs GN 526.1 258

Scaling sets 254

Screws, Hygienic Design, St. Steel GN 1580 790

Screw drivers, for indexing plungers GN 613.1 648

Screw drivers, for spring plungers GN 611.5 735

Screw drivers, for spring plungers GN 616.5 732/733

Screw-on levels, for mounting with screws GN 2282 251

Sealing rings, Hygienic Design GN 7600 881

Sensor accessories, for pneumatic fastening clamps GN 893.1 611




Sensor holders, Aluminum GN 271.4 1239



Sensor holders, for attachment clamp mountings, St. Steel GN 479 1262

Serrated locking plates, Steel/St. Steel GN 187.4 824

Set collars, semi-split, Aluminum GN 706.2 858

Set collars, semi-split, Aluminum, with hand levers GN 706.4 862

Set collars, semi-split, St. Steel GN 706.2 858

Set collars, semi-split, St. Steel, with hand levers GN 706.4 804

Set collars, semi-split, Steel GN 706.2 858

Set collars, semi-split, Steel, with hand levers GN 706.4 858

Set collars, split, Aluminum GN 707.2 859

Set collars, split, Plastic GN 707.5 850

Set collars, split, St. Steel GN 707.2 859

Set collars, split, Steel GN 707.2 859

Set collars, St. Steel GN 705 856

Set collars, Steel GN 705 856

Set collars see also:

Quick release set collars

Threaded set collars

Setting bolts, Steel GN 251 838

Setting bolts, Steel, with limit switch GN 251.2 839

Setting bolts, with retaining magnet GN 251.6 1408

Shackles, for profile systems, Steel GN 967 1272

Shackles, Steel, cranked GN 585 1077

Shackles, Steel, straight GN 584 1076



Shaft clamping units, „trueround“ GN 928 486

Sheet metal hinges, St. Steel GN 136 965

Sheet metal hinges, Steel GN 136 965

Sheet metal punches, for mounting latches GN 123 941

Shim kit accessories GN 871 607

Shoulder screws, St. Steel ISO 7379 789

Shoulder screws, Steel ISO 7379 788

Side thrust pins, spring loaded, press on type GN 714 741



Side thrust pins, spring loaded, with thread GN 713 742

Sight glasses, ATEX, Aluminum/ESG-Glass GN 743.6 1099

Silicone buffers, with female thread GN 256 1086

Silicone buffers, with threaded stud GN 256 1086

Single post bracket / bracket accessories GN 867.1 601

Single post bracket / Y-bracket accessories GN 869.1 604

Single post coupling / Y-coupling accessories, GN 867 600

Sling see also:

Lifting eye bolts

Lifting eye nuts

Load rings

Slotted locknuts, self-locking GN 1804.1 802

Slotted locknuts, Steel/St. Steel DIN 1804 801

Slotted locknuts, with threaded locking GN 1804.2 803

Snap locks GN 315.1 936

Snap locks, locking distance adjustable GN 315 934

Spacer plate, for position indicators GN 953.1 297

Spacer plate, for position indicators GN 954.1 299

Spacer plates, for Hinges GN 2370 961

Spherical levelling washers, St. Steel GN 350.3 821

Spherical levelling washers, Steel GN 350.3 821

Spherical washers, combined, St. Steel GN 6319.1 820

Spherical washers, combined, Steel GN 6319.1 820

Spherical washers, St. Steel DIN 6319 819

Spherical washers, Steel DIN 6319 818

Spiral retaining cables, with 2 key rings GN 111.4 878

Split hubs, St. Steel GN 150.5 385

Split hubs, Steel GN 150 385

Spoked handwheels, Aluminum GN 322 176



Spoked handwheels, for linear actuators Ø 40, 40 GN 924.40 1349

Spoked handwheels, for linear actuators Ø 50, 50 GN 924.50 1349

Spoked handwheels, for linear actuators Ø 60 GN 924.60 1349

Spoked handwheels, Plastic GN 522 178

Spoked handwheels, Plastic GN 555 180

Spoked handwheels, Plastic, St. Steel bushing GN 522.5 179

Spring bolts, Steel/St. Steel GN 313 691

Spring cotter pins, St. Steel GN 1024 880

Spring cotter pins, Steel GN 1024 880

Spring elements, Steel GN 513 736

Spring loaded shells, Steel/St. Steel GN 610 726

Spring latches, for welding, Steel/St. Steel GN 722.1 717

Spring latches, with flange for surface mounting GN 722.2 714

Spring latches, with flange for surface mounting GN 722.3 712

Spring latches, with/without locking GN 416 675

Spring plungers, double ended, press on type GN 614.2 724

Spring plungers, glatt, without collar, St. Steel GN 614.3 725

Spring plungers, press on type GN 614 722

Spring plungers, press on type GN 614.5 723

Spring plungers, press on type, St. Steel GN 614.4 734

Spring plungers, with long bolt, Steel GN 611 735

Spring plungers, with bolt, Steel/St. Steel GN 615.4 731

Spring plungers, with bolt, St. Steel GN 616 733

Spring plungers, with bolt, St. Steel GN 615.1 730

Spring plungers, with bolt, Steel GN 615.1 730

Spring plungers, with bolt, Steel GN 616 732

Spring plungers, with collar, St. Steel GN 815 721

Spring plungers, with collar, Steel GN 815 721

Spring plungers, with limit switch GN 615.7 737

Spring plungers, with internal hexagon, St. Steel GN 615.3 719

Spring plungers, with internal hexagon, Steel GN 615.3 719

Spring plungers, with slot, Plastic GN 615.2 720

Spring plungers, with slot, St. Steel GN 615 718

Spring plungers, with slot, Steel GN 615 718

Spring plungers see also:

Cam action indexing plungers

Indexing plungers

Locking plungers

Mini indexing plungers

Side thrust pins

Spring elements

Spring latches

Spring rings, for ball transfer units GN 509.3 1372

Square linear actuators, for 1 linear actuator connectors GN 291.1 1340



Square U-Bolts, for latch type toggle clamps GN 951.1 560

Square U-Bolts, for latch type toggle clamps GN 951.2 561

Star knobs, Plastic, SOFTLINE GN 5337.6 408

Stop locks, with 4 indexing positions GN 702 938

Stop locks, with 4 indexing positions GN 720 939

Strainer fittings, St. Steel GN 7405 1133

Strainers, St. Steel GN 7403.1 1132

Swing bolts, Steel/St. Steel DIN 444 776

Swing bolts, with long threaded bolt, Steel/St. Steel GN 1524 777

Swing nuts, Steel GN 444.2 806

Swivel ball joints, Aluminum GN 784 1264

Swivel clamp connector, Aluminum GN 273 1222






Swivel clamp connector, split assembly, Aluminum GN 279 1228

Swivel clamp connector bases, Aluminum GN 271 1220





Swivel clamp connector joints, Aluminum GN 281 1230








Swivel clamp connector joints, two-part, Aluminum GN 289 1238

Swivel clamp mountings, Aluminum GN 482 1257

System handles, Aluminum GN 669 144

ST → PageStar knobs, Aluminum GN 5336 411

Star knobs, Aluminum DIN 6336 396

Star knobs, Cast iron DIN 6336 396

Star knobs, Hygienic Design, St. Steel GN 5435 419

Star knobs, Plastic DIN 6336 398

Star knobs, Plastic GN 5337.2 406

Star knobs, Plastic, protruding St. Steel bushing GN 6336.1 400

Star knobs, Plastic, protruding St. Steel bushing GN 6336.2 400

Star knobs, Plastic, protruding Steel bushing GN 6336.1 400

Star knobs, Plastic, protruding Steel bushing GN 6336.2 400

Star knobs, Plastic, SOFTLINE GN 5337.6 408

Star knobs, St. Steel DIN 6336 396

Star knobs, St. Steel A2, GN 5334 414

Star knobs, St. Steel A2, GN 5335 416

Star knobs, St. Steel A4, GN 5334.4 414

Star knobs, St. Steel A4, GN 5335.4 418

Star knobs see also:

Hand knobs

Safety starknobs

Triangular knobs

Tristar knobs

Star knobs with threaded stud, loss protection GN 6336.13 405

Star knobs with threaded stud, Plastic GN 5337.2 407

Star knobs with threaded stud, Plastic, SOFTLINE GN 5337.6 408

Star knobs with threaded stud, St. Steel GN 6336.5 397

Star knobs with threaded stud, St. Steel A2 GN 5334 415

Star knobs with threaded stud, St. Steel A2 GN 5335 417

Star knobs with threaded stud, St. Steel A4 GN 5334.4 415

Star knobs with threaded stud, St. Steel, Aluminum GN 6336.5 397

Star knobs with threaded stud, St. Steel, Plastic GN 6336.5 399

Star knobs with threaded stud, Steel, Cast iron GN 6336.4 397

Star knobs with threaded stud, Steel, Plastic GN 6336.4 399

Star knobs with threaded stud, with ball pin GN 6336.11 403

Star knobs with threaded stud, with brass/plastic pivot GN 6336.10 402

Star knobs with threaded stud, with movable thrust pad GN 6336.12 403

Studs, for T-Nuts DIN 6379 868

T → PageT-angle connector clamps, Aluminum GN 191 1208

T-angle connector clamps, Aluminum GN 192 1210

T-angle connector clamps, multi, Aluminum GN 194 1213

T-angle connector clamps, multi, Aluminum GN 195 1214

T-angle connector clamps, St. Steel GN 191 1208

T-angle connector clamps, St. Steel GN 192.5 1211

T-angle connector clamps, split assembly, Aluminum GN 193 1212

T-bracket / double post bracket accessories GN 869.2 605

T-Clamp mountings, Aluminum GN 476 1251

T-coupling / double post coupling accessories GN 868 602

T-Handles, Aluminum GN 563.2 66

T-Handles, Plastic GN 563 68

T-Handles screws, Plastic GN 563.1 69

T-Nuts, for profile systems GN 506.1 873

T-Nuts, for profile systems, Steel GN 506 872

T-Nuts, for profile systems, Steel GN 506.2 874

T-Nuts, for profile systems, Steel GN 507 875

T-Nuts, shallow GN 230 833

T-Nuts, St. Steel DIN 508 865

T-Nuts, Steel DIN 508 864

T-Nuts, Steel, for profile systems GN 505 871

T-Nuts, with slip proof GN 508.2 866

T-nuts / T-screws see also:

Rhombus T-nuts

T-Slot bolts

T-Slot nuts

T-Slot bolts, St. Steel, for Profile systems GN 505.5 870

T-Slot bolts, Steel DIN 787 869

T-Slot bolts, Steel, for Profile systems GN 505.4 870

T-Swivel clamp mountings, Aluminum GN 483 1258

Tapered knobs, Plastic GN 419 50

Telescopic linear slides, with one side extension GN 2406 1293

Tension levers, adjustable, St. Steel GN 212.5 348/349

Tension levers, adjustable, Steel GN 212.3 346/347

Tension levers, fixed, St. Steel GN 212 377

Tension levers, fixed, Steel GN 212 377

Tension levers, flat, adjustable, St. Steel GN 125.5 354

Tension levers, flat, adjustable, Steel GN 125 352

Three lobe knobs, Hygienic Design, St. Steel GN 5445 429

Three lobe knobs, St. Steel A2, GN 5345 428

Three lobe knobs, St. Steel A4, GN 5345.4 428

Thread adapters, St. Steel GN 480.8 1254

Threaded flanges, for profile systems, Steel GN 3490 1273

Threaded plugs, Aluminum GN 441 1119

Threaded plugs, Aluminum GN 442 1119

Threaded plugs, Plastic GN 745 1111

Threaded plugs, Plastic GN 745.2 1111

Threaded plugs, with conical thread, St. Steel DIN 906 1116

Threaded plugs, with conical thread, Steel DIN 906 1116

Threaded plugs, with internal hexagon, Steel GN 749 1115

Threaded plugs, with internal hexagon, Steel GN 908 1117

Threaded plugs, with/without re-fill/drain symbol GN 741 1114



Threaded plugs, with/without re-fill/drain symbol GN 742 1114

Threaded plugs see also:

ATEX-Threaded plugs

Magnetic plugs

Threaded set collars, Steel/St. Steel GN 706.3 804

Thrust pads, Plastic, for grub screw GN 631 798

Thrust pads, St. Steel, for grub screw GN 631.5 798

Thrust pads, Steel, for grub screw DIN 6311 794

Thrust pads, Steel, for grub screw GN 6311.1 795

Thrust springs, for serrated locking plates GN 187.2 827

Toggle clamp spindle assemblies, GN 802 588

Toggle clamp spindle assemblies, GN 804 585

Toggle clamp spindle assemblies, St. Steel GN 708.1 587

Toggle clamp spindle assemblies, St. Steel GN 807 586

Toggle clamp spindle assemblies, St. Steel GN 903 589

Toggle clamp spindle assemblies, Steel GN 708.1 587

Toggle clamp spindle assemblies, Steel GN 807 586

Toggle clamp spindle assemblies, Steel GN 903 589

Toggle clamps see also:

C-Clamps

Hook type toggle clamps

Horizontal acting toggle clamps

Knee lever modules

Pneumatic fastening clamps

Pneumatic toggle clamps

Push-pull type toggle clamps

Toggle Latches

Vertical acting toggle clamps

Toggle latches, Steel/St. Steel GN 821 614


Toggle latches, Steel/St. Steel GN 831.1 618









Tommy nuts, fixed bar DIN 6305 372

Tommy nuts, movable bar DIN 6307 373

Tommy screws, fixed bar DIN 6304 374

Tommy screws, movable bar DIN 6306 375

Torque limiting knobs, Aluminum GN 3663 447

Torque limiting knob screws, Aluminum GN 3663 447

Tri-ball handles, Steel GN 10 227

Triangular knobs, St. Steel GN 5339.5 427

Tristar knobs, St. Steel bushing, Plastic GN 5330.5 430

Tristar knobs, Steel bushing, Plastic GN 5330 430

Tristar knobs with threaded stud, Plastic GN 5330 431

Tube connector joints, Aluminum GN 242 1218

Tube connector joints, split assembly, Aluminum GN 241 1217

Tube supports, split assembly , Aluminum GN 231 1216

Tubular arch handles, Aluminum-/St. Steel-Tube GN 666.4 148

Tubular handles, Aluminum GN 333.1 130

Tubular handles, Aluminum GN 333.3 131

Tubular handles, Aluminum-/St. Steel-Tube GN 666 146

Tubular handles, Aluminum-/St. Steel-Tube GN 666.1 147

Tubular handles, cranked, Aluminum GN 333.2 137

Tubular handles, cranked, Aluminum GN 333 136

Tubular handles, St. Steel GN 333.5 134



Tubular handles, with power switching function GN 331 132

Tubular handles, with power switching function GN 332 138

Tubular handles see also:

Edge handles

Handle tubes

Oval tubular handles

System handles

Turret levers, Steel GN 213 384

Twistable two-way clamp mountings, Aluminum GN 490 1255 Two-way clamp mountings, Aluminum GN 131 1188

Two-way clamp mountings, Aluminum GN 133 1191

Two-way clamp mountings, Aluminum GN 474 1248

Two-way clamp mountings, multi part assembly, Al GN 134 1192

Two-way clamp mountings, multi part assembly, Al GN 135 1193

Two-way clamp mountings, St. Steel GN 131 1188

Two-way clamp mountings, St. Steel GN 132.5 1189

Two-way clamp mountings, twistable, Aluminum GN 475 1250

Two-way connector clamps, Aluminum GN 132 1190

U → Page„U“ handles GN 423 98

U-Magnets, with bore GN 62 1405

Universal joints, for ordinary applications GN 9080 1150

Universal joints, with friction bearing, single/double DIN 808 1144

Universal joints, with friction bearing, single/double, DIN 808 1145

Universal joints, with needle bearing, single/double DIN 808 114

Universal joint shafts, with friction bearing GN 808.2 1146

Universal joint shafts, with needle bearing GN 808.3 1149

V → PageVertical acting toggle clamps, „Longlife“ GN 910 506

Vertical acting toggle clamps, „Longlife“ GN 910.1 508

Vertical acting toggle clamps, St. Steel GN 810 502

Vertical acting toggle clamps, St. Steel GN 810.1 504

Vertical acting toggle clamps, Steel GN 810 502

Vertical acting toggle clamps, Steel GN 810.1 504

Vertical acting toggle clamps, Steel GN 812 514

Vertical acting toggle clamps, Steel GN 812.1 516

Vertical acting toggle clamps, heavy duty GN 813 518

Vertical hook type toggle clamps, heavy duty, Steel GN 852.1 558

Vertical hook type toggle clamps, St. Steel GN 851.1 546


W → PageWaist shaped knobs, flat, St. Steel GN 75.5 59

Waist shaped knobs, flat, Steel GN 75 59

Waist shaped knobs, Hygienic Design, St. Steel GN 76 60

Washer rings, Steel/ St. Steel, axial ball bearing GN 6344 823

Washers, heavy duty, Steel GN 6339 812

Washers, St. Steel GN 6343 811

Washers, Steel DIN 6340 816

Washers, Steel/St. Steel GN 6341 810

Washers, Steel/St. Steel with axial friction bearing GN 6342 822

Washers see also:

Bezel discs

C-Washers

Captive C-Washers

Countersunk washers

Serrated locking plates

Spherical levelling washers

Spherical washers

Wedge clamps GN 920.1 482

Welding sockets, Steel GN 7490 1135

Wide base plate connector clamps, split assembly GN 167 1207

Wing nuts, Plastic GN 532 432

Wing nuts, St. Steel GN 432 441



Wing nuts, with protruding hub, Plastic GN 532.1 434

Wing screws, St. Steel GN 431 441



Wing screws, St. Steel threaded stud GN 531 433

Wing screws, Steel threaded stud GN 531 433

Wing screws, with protruding hub, Plastic GN 531.1 435

Wipers, for cam roller linear guide rails GN 2422, GN 2428 1305

Workholding bolts DIN 6321 834

Workholding bolts, with ball-type shoulder GN 6322 835


| Numerical product index

Numerical product index |

Table of contents Numerical product index0-9


000 → PageGN 000.4 206

GN 000.5 207

GN 000.8 283

GN 000.9 288

GN 000.13 291

GN 10 227

DIN 13 1477

GN 20 1034/1035

GN 21 1038

GN 23 1038

GN 30 1044

GN 31 1046

GN 32 1048

GN 33 1050

DIN 39 41

GN 40 1040

GN 41 1042

GN 42 1040

GN 43 1042

GN 50.1 1382

GN 50.2 1384

GN 50.25 1386

GN 50.3 1383

GN 50.4 1388

GN 50.45 1389

GN 50.5 1390

GN 50.6 1385

GN 51.2 1394

GN 51.3 1396

GN 51.4 1393

GN 51.5 1392

GN 51.6 1395

GN 51.7 1407

GN 52.1 1398

GN 52.2 1399

GN 52.3 1400

GN 52.4 1402

GN 52.5 1403

GN 53.1 1406

GN 54.1 1397

GN 55.1 1410

GN 55.2 1411

GN 55.3 1412

GN 55.4 1413

GN 56 1416

GN 58 1391

GN 60 1404

GN 62 1405

GN 70 1414

GN 70.1 1415

GN 75 59

GN 75.5 59

GN 75.6 60

GN 76 58

DIN 79 1424

DIN 98 40

DIN 99 364

GN 99.2 356/357

GN 99.5 368

GN 99.6 368

GN 99.7 369

GN 99.8 369

100 → PageGN 101 336/337

GN 109 1425

GN 110 1422

GN 110.1 1423

GN 111 876

GN 111.2 877

GN 111.3 876

GN 111.4 878

GN 111.5 876

GN 111.6 879

GN 111.7 1426

GN 112.1 226

GN 113.1 758

GN 113.3 748

GN 113.4 748

GN 113.5 749

GN 113.6 749

GN 113.7 750

GN 113.8 750

GN 114.2 752

GN 114.3 753

GN 114.6 753

GN 115 896 ff.

GN 115.1 904

GN 115.3 906

GN 115.5 908

GN 115.6 904

GN 115.7 910

GN 115.8 930 ff.

GN 115.10 912 ff.

GN 116.1 916

GN 117 922

GN 119 924/926

GN 119.2 940

GN 119.3 928

GN 120 942

GN 120.1 943

GN 120.2 944

GN 123 941

GN 124.1 757

GN 124.2 756

GN 125 352/353

GN 125.5 354/355

GN 127 980

GN 128 990

GN 128.2 991

GN 129 974

GN 129.2 976

GN 129.3 977

GN 129.5 975

GN 131 1188

GN 131.1 1330

GN 131.2 1330

GN 132 1190

GN 132.1 1331

GN 132.2 1331

GN 132.5 1189

GN 133 1191

GN 134 1192

GN 134.1 1342

GN 135 1193

GN 135.1 1343

GN 136 965

GN 138 966

GN 139.1 992

GN 139.2 992

GN 139.3 994

GN 139.4 994

GN 139.5 996

GN 139.6 996

GN 141 1194

GN 145 1195

GN 145.1 1332

GN 146 1196

GN 146.1 1333

GN 146.3 1196

GN 146.5 1197

GN 146.6 1197

GN 147 1198

GN 147.1 1344

GN 147.3 1199

GN 148 1052

GN 148.2 1055

GN 150 385

GN 150.5 385

GN 151 967

GN 151.4 981

GN 159 968

GN 159.1 970

GN 161 972

GN 161.1 988

GN 161.2 989

GN 162 1200

GN 162.1 1334

GN 162.3 1201

GN 163 1202

GN 163.1 1335

GN 163.5 1203

GN 164 253

GN 165 1204

GN 165.1 1345

GN 166 1205

GN 167 1207

DIN 172 830

GN 172.1 683

DIN 179 830 GN 179.1 683

GN 181 116

GN 183 829

GN 184 814

GN 184.5 815

GN 185 815

GN 187.1 826

GN 187.2 827

GN 187.4 824

GN 191 1208

GN 191.1 1336

GN 192 1210

GN 192.1 1337

GN 192.5 1211

GN 193 1212

GN 194 1213

GN 195 1214

GN 196 1215

Numerical product index


200 → PageGN 200 272/274

GN 201 51 GN 203 42

GN 204 365

GN 206 370

GN 206.1 371

GN 211 383

GN 212 377

GN 212.3 346/347

GN 212.5 348/349

GN 213 384

GN 214.2 754

GN 214.3 755

GN 214.6 755

GN 215 278

GN 218 927

GN 223 382

GN 224.1 121

GN 224.5 121

GN 225 97

GN 226 216

GN 226.1 216

GN 227 219

GN 227.1 185

GN 227.2 184

GN 227.4 184

DIN 228 1476

GN 230 833

GN 231 1216

GN 233 984

GN 237 959/963

GN 237.1 964

GN 238 978

GN 239.3 1002

GN 239.4 1002

GN 239.6 998

GN 239.7 998

GN 239.8 1000

GN 240 1171

GN 240.1 1172

GN 240.2 1173

GN 241 1217

GN 242 1218

GN 249 728

GN 250 729

GN 251 838

GN 251.2 839

GN 251.6 1408

GN 252 791

GN 252.5 791

GN 253 1084

GN 254 1085

GN 256 1086

GN 264 255

GN 268 256

GN 269 224

GN 271 1220

GN 271.4 1239

GN 272 1221

GN 272.4 1240

GN 273 1222

GN 273.1 1338

GN 273.4 1241

GN 274 1223

GN 274.1 1339

GN 275 1224

GN 276 1225

GN 277 1226

GN 278 1227

GN 279 1228

GN 281 1230

GN 282 1231

GN 283 1232

GN 284 1233

GN 285 1234

GN 286 1235

DIN ISO 286 1479

GN 287 1236

GN 288 1237

GN 289 1238

GN 291 1326

GN 291.1 1340

GN 292 1328

GN 292.1 1325

GN 293 1329

GN 293.1 1325

GN 295 1350

GN 296 1351

GN 297 1353

GN 298 1354

GN 299 1346

300 → PageGN 300 318/319

GN 300.1 322/323

GN 300.4 332/333

GN 300.5 324/325

GN 300.6 324/325

GN 302 334/335

GN 303 328/329

GN 303.1 330/331

GN 305 326/327

GN 306 320

GN 310 65

GN 312 360/361

GN 313 691

GN 315 934

GN 315.1 936

GN 316 362

DIN 319 46/47/48

GN 319.2 38

GN 319.5 38

GN 321 188

GN 321.4 204

GN 321.5 204

GN 321.6 208

GN 322 176

GN 322.3 198

GN 322.4 204

GN 322.5 204

GN 322.7 198

GN 323 188

GN 323.4 204

GN 323.5 204

GN 323.8 284

GN 323.9 292

GN 324 176

GN 327 210

GN 330 1004

GN 331 132

GN 332 138

GN 333 136

GN 333.1 130

GN 333.2 137

GN 333.3 131

GN 333.5 134

GN 333.8 135

GN 333.9 135

GN 334 142

GN 334.1 143

GN 337 986

GN 338 817

GN 339 1032

GN 342.1 1022

GN 342.2 1022

GN 343.1 1014

GN 343.2 1014

GN 343.3 1016

GN 343.4 1016

GN 343.5 1018

GN 343.6 1018

GN 343.7 1020

GN 343.8 1020

GN 344.1 1026

GN 344.6 1026

GN 345.1 1028

GN 345.6 1028

GN 346 799

GN 347 800

GN 348.1 1058

GN 349 1056

GN 350 850

GN 350.1 851

GN 350.2 852

GN 350.3 821

GN 350.5 853

GN 351 1080

GN 352 1081

GN 353 1082

GN 355 854

GN 355.1 855

GN 366 152

GN 369 225

GN 374 256

GN 391 1352

400 → PageGN 409.1 836

GN 409.2 837

GN 411.2 488

GN 412 674

GN 412.1 698

GN 412.2 696

GN 412.3 697

GN 413 659

GN 414 684

GN 414.1 685

GN 416 675

GN 416.1 676

GN 417 678/679

GN 417.1 677

GN 418.1 478

GN 418.2 476

GN 419 50

GN 420 448

GN 421 449

GN 421.10 450

GN 421.11 451

GN 421.12 451

GN 423 98

GN 424.1 120

GN 424.5 120

GN 425 102/103

GN 425.1 106/107

GN 425.2 122

GN 425.3 104

GN 425.5 123

GN 425.7 105

GN 425.8 124

GN 426 108

GN 426.1 114

GN 426.3 111

GN 426.5 109

GN 426.6 115

GN 427 100

GN 427.5 100

GN 428 117

GN 429 110

GN 430 156

GN 430.1 156

GN 431 441

GN 432 441

GN 433 440

GN 434 440

GN 436 262

GN 436.1 263

GN 437 982

GN 441 1119

GN 442 1119



GN 552 1124

GN 552.6 1126

GN 555 180

GN 558 231

GN 559 94

GN 563 68

GN 563.1 69

GN 563.2 66

GN 564 83

GN 565 80

GN 565.1 81

GN 565.2 86

GN 565.3 93

GN 565.4 118

GN 565.5 82

GN 565.7 87

GN 565.9 118

GN 570.2 221

DIN 580 1060

GN 581 1062

GN 581.5 1064

DIN 582 1061

GN 583 1066

GN 584 1076

GN 585 1077

GN 586.1 1070

GN 587 1072

GN 589 1074

GN 598 35

GN 598.1 36

GN 598.3 43

GN 598.5 43

GN 599.5 37

600 → PageGN 601 367

GN 603 342/343

GN 603.1 344/345

GN 604 338/339

GN 604.1 340/341

GN 605 783

GN 606 784/785

GN 607 660

GN 607.1 661

GN 607.2 662

GN 607.3 663

GN 607.4 664

GN 607.5 665

GN 607.9 662

GN 608 666

GN 608.1 667

GN 608.5 666

GN 608.6 667

GN 609.5 694

GN 610 726

GN 611 735

GN 611.5 735

GN 612 704

GN 612.1 699

GN 612.2 710

GN 612.3 716

GN 612.8 705

GN 612.9 711

GN 612.10 715

GN 613 648

GN 613.1 648

GN 614 722

GN 614.1 738

GN 614.2 724

GN 614.3 725

GN 614.4 734

GN 614.5 723

GN 615 718

GN 615.1 730

GN 615.2 720

GN 615.3 719

GN 615.4 731

GN 615.7 737

GN 616 732/733

GN 616.5 732/733

GN 617 646

GN 617.1 647

GN 618 649

GN 623 380

GN 623.5 380

GN 625 89

GN 628 96

GN 628.2 96

GN 630 161

GN 630.1 88

GN 631 798

GN 631.5 798

GN 632.1 797

GN 632.5 797

GN 638 1030

GN 648.1 1154

GN 648.2 1155

GN 648.5 1156

GN 648.6 1157

GN 648.8 1158

GN 648.9 1159

GN 649 1274

GN 649.1 1275

GN 650 1106

GN 650.1 1106

GN 650.2 1110

GN 650.4 1108

DIN 653 459

GN 653.2 461

GN 653.10 460

GN 665 119

GN 666 146

GN 666.1 147

GN 666.4 148

GN 666.5 150

GN 666.7 150

GN 667 140

GN 667.2 141

GN 668 95

GN 669 144

GN 675 56/57

GN 675.1 56

GN 676 62/63

GN 676.1 64

GN 676.5 64

DIN 444 776

GN 444.2 806

GN 451 1080

GN 452 1081

GN 453 1083

GN 454 1088

DIN 464 457

DIN 466 456

DIN 467 458

DIN 468 222

DIN 469 223

GN 471 220

GN 471.1 220

GN 471.3 228

GN 472.3 229

GN 472.5 229

GN 473 1246

GN 474 1248

GN 474.1 1249

GN 475 1250

GN 476 1251

GN 477 1247

GN 478 1252

GN 479 1262

GN 479.1 1263

GN 480 1253

GN 480.1 1276

GN 480.7 1254

GN 480.8 1254

GN 481 154

GN 482 1257

GN 483 1258

GN 484 1259

GN 485 1256

GN 490 1255

GN 491 1360

GN 491.1 1367

GN 492 1364

500 → PageGN 505 871

GN 505.4 870

GN 505.5 870

GN 506 872

GN 506.1 873

GN 506.2 874

GN 507 875

DIN 508 864/865

GN 508.1 867

GN 508.2 866

GN 509 1368

GN 509.1 1370

GN 509.3 1372

GN 509.4 1371

GN 511 1260

GN 511.1 1261

GN 513 736

GN 514 690

GN 516 918

GN 516.1 921

GN 516.5 920

GN 519 52

GN 519.1 53

GN 519.6 54

GN 520.1 192

GN 520.2 193

GN 521 190

GN 521.3 194

GN 521.5 191

GN 521.6 195

GN 522 178

GN 522.3 200

GN 522.5 179

GN 522.6 201

GN 526 257

GN 526.1 258

GN 527.1 218

GN 528 90

GN 528.1 91

GN 528.4 91

GN 531 433

GN 531.1 435

GN 532 432

GN 532.1 434

GN 534 442/443

GN 535 452

GN 536 452

GN 537 1103

GN 537.1 1103

GN 541.1 1102

GN 543.1 1134

GN 548.1 1120



700 → PageGN 700 276

GN 702 938

GN 704 863

GN 705 856

GN 706.2 858

GN 706.3 804

GN 706.4 862

GN 707.2 859

GN 707.5 860

GN 708.1 587

GN 709.1 844

GN 709.2 845

GN 709.3 846

GN 709.6 847

GN 709.7 848

GN 709.8 849

GN 709.15 844

GN 709.25 845

GN 709.35 846

GN 710 1169

GN 711 240

GN 711.1 240

GN 711.2 241

GN 711.3 241

GN 712 706

GN 712.1 707

GN 713 742

GN 713.1 742

GN 714 741

GN 715 740

GN 715.1 740

GN 715.2 745

GN 716 739

GN 717 656/657

GN 719.2 49

GN 720 939

GN 721 708

GN 721.1 708

GN 721.5 709

GN 721.6 709

GN 722.1 717

GN 722.2 714

GN 722.3 712

GN 723.3 266

GN 723.4 264

GN 725 84

GN 725.1 85

GN 726 259

GN 726.1 260

GN 726.2 261

GN 727 270

GN 728 92

GN 728.5 92

GN 729 269

GN 730 158

GN 730.5 159

GN 731 162

GN 731.1 164

GN 732 787

GN 735 214

GN 736 212

GN 736.1 213

GN 738 1112

GN 738.1 1112

GN 740.1 1111

GN 741 1114

GN 742 1114

GN 743 1096

GN 743.1 1096

GN 743.2 1097

GN 743.3 1097

GN 743.4 1098

GN 743.5 1098

GN 743.6 1099

GN 743.7 1100

GN 743.8 1100

GN 744 1101

GN 745 1111

GN 745.1 1111

GN 745.2 1111

GN 747.1 1111

GN 749 1115

GN 750 378

GN 751 1160 ff.

GN 751.1 1164

GN 752 1165

GN 753 1373

GN 771.1 832

GN 782 1170

GN 784 1264

GN 784.1 1266

DIN 787 869

GN 798 32 GN 798.1 33

GN 798.2 34

GN 798.3 44

GN 798.5 44

GN 798.7 45

GN 798.8 45

800 → PageGN 801 590

GN 802 588

GN 804 585

GN 806 1089

GN 807 586

DIN 808 1144 ff.

GN 808.1 1151

GN 808.2 1146

GN 808.3 1149

GN 809 591

GN 810 502

GN 810.1 504

GN 812 514

GN 812.1 516

GN 813 518

GN 815 721

GN 816 686

GN 816.1 688

GN 817 650

GN 817.1 654

GN 817.2 652

GN 817.3 680

GN 817.4 653

GN 817.5 681

GN 817.8 651

GN 817.9 655

GN 820 520

GN 820.1 522

GN 820.2 528

GN 820.3 524

GN 820.4 526

GN 821 614

GN 822 668

GN 822.1 668

GN 822.6 670

GN 822.7 671

GN 822.8 672

GN 822.9 673

GN 825.1 128

GN 825.2 126

GN 826 268

GN 831 616

GN 831.1 618

GN 831.2 618

GN 832 620

GN 832.1 621

GN 832.2 622

GN 832.3 623

GN 832.4 624

GN 833 625

GN 834 436

GN 835 437

GN 840 530

GN 841 534

GN 842 536

GN 843.1 538

GN 844 532

GN 850 540

GN 851 542

GN 851.1 546

GN 851.2 548

GN 851.3 544

GN 852 550/552

GN 852.1 558

GN 852.3 554/556

GN 853 562/564

GN 854 568

GN 855 570

GN 858 566

GN 860 572

GN 861 574

GN 862 576

GN 862.1 578

GN 863 563

GN 864 594

GN 865 596

GN 866 598

GN 867 600

GN 867.1 601

GN 868 602

GN 868.1 603

GN 869.1 604

GN 869.2 605

GN 870 610

GN 871 607

GN 872 606

GN 873 608

GN 880 1122

GN 880.1 1121

GN 881 1127

GN 882 1129

GN 883 1128

GN 884 1130

GN 890 582

GN 893.1 611

GN 893.2 611

GN 893.3 611

GN 893.4 611

GN 896.1 584

GN 896.2 584

GN 896.3 584

900 → PageGN 900 1314

GN 900.1 1316

GN 900.2 1317

GN 900.3 1318

GN 900.4 1320

GN 900.5 1321

GN 900.6 1322

GN 903 589

DIN 906 1116

DIN 908 1117

GN 909 695

GN 909.5 695

GN 910 506

GN 910.1 508

GN 910.2 510

GN 910.3 512

GN 910.5 513

GN 910.6 513

GN 910.7 513

GN 910.8 513

GN 910.9 513

GN 911 1242

GN 911.3 1242

GN 913.2 780

GN 913.3 778

GN 913.5 779

GN 913.6 1409

GN 917 481

GN 917.1 481

GN 918 472

GN 918.1 474

GN 918.2 475

GN 918.5 472

GN 918.6 474

GN 918.7 475

GN 919 480

GN 920.1 482

GN 920.2 484

GN 923 186

GN 923.18 1348

GN 923.3 196

GN 923.30 1348

GN 923.40 1348

GN 923.7 196

GN 924 174

GN 924.3 197

GN 924.40 1349

GN 924.50 1349

GN 924.60 1349

GN 924.7 197

GN 927 468

GN 927.3 468



5000 → PageGN 5330 430/431

GN 5330.5 430

GN 5334 414/415

GN 5334.4 414/415

GN 5335 416/417

GN 5335.4 418

GN 5336 411

GN 5337.2 406/407

GN 5337.3 410

GN 5337.6 408

GN 5337.9 409

GN 5339.5 427

GN 5345 428

GN 5345.4 428

GN 5435 419

GN 5445 429

GN 5860 1068

6000 → PageDIN 6303 454/455

GN 6303.1 462

DIN 6304 374

DIN 6305 372

GN 6305.1 376

DIN 6306 375

DIN 6307 373

DIN 6311 794

GN 6311.1 795

GN 6311.3 796

GN 6311.4 1024

DIN 6319 818/819

GN 6319.1 820

DIN 6320 841

DIN 6321 834

GN 6321.1 840

GN 6322 835

DIN 6330 807

DIN 6331 808

DIN 6332 793

DIN 6335 420/422

GN 6335.1 424

GN 6335.2 424

GN 6335.4 421 ff.

GN 6335.5 421 ff.

GN 6335.9 426

DIN 6336 396/398

GN 6336.1 400

GN 6336.2 400

GN 6336.3 404

GN 6336.4 397 ff.

GN 6336.5 397 ff.

GN 6336.10 402

GN 6336.11 403

GN 6336.12 403

GN 6336.13 405

DIN 6337 366

GN 6337.3 358/359

GN 6339 812

DIN 6340 816 GN 6341 810

GN 6342 822

GN 6343 811

GN 6344 823

DIN 6371 828

DIN 6379 868

DIN 6885 842/843

7000 → PageGN 7017 658

GN 7336 444

GN 7336.5 445

GN 7336.7 692

GN 7336.8 693

ISO 7379 788/789

GN 7403 1131

GN 7403.1 1132

GN 7405 1133

GN 7490 1135

GN 7600 881

GN 7603 1118

8000 → PageGN 8330 612

9000 → PageGN 9053 302

GN 9054 304

GN 9080 1150

70000 → PageDIN 71752 1160 ff.

DIN 71802 1166 ff.

GN 927.4 470

GN 927.5 470

GN 927.7 471

GN 928 486

GN 928.1 486

GN 930 153

GN 933.5 781

GN 949 183

DIN 950 181

GN 950.1 181

GN 950.6 182

GN 951.1 560

GN 951.2 561

GN 952.1 306

GN 953 296

GN 953.1 297

GN 953.6 308

GN 954 298

GN 954.1 299

GN 954.6 308

GN 955 300

GN 957 307

GN 960 1268

GN 961 1267

GN 963 1269

GN 965 1428

GN 967 1272

GN 968 1438

GN 970 1270/1271

GN 990 1277

GN 991 1278

GN 992 1059

GN 992.5 1059

1000 → PageGN 1024 880

GN 1130 1078

GN 1132 1079

GN 1524 777

GN 1580 790/809

DIN 1804 801

GN 1804.1 802

GN 1804.2 803

DIN 1810 801

2000 → PageGN 2180 948

GN 2182 950

GN 2184 954

GN 2277 244

GN 2277.1 246

GN 2278 247

GN 2279 248

GN 2280 249

GN 2281 250

GN 2282 251

GN 2342 760

GN 2344 762

GN 2370 961

GN 2372 960

GN 2374 962

GN 2402 1291

GN 2404 1292

GN 2406 1293

GN 2408 1294

GN 2410 1295

GN 2422 1301

GN 2424 1302

GN 2424.1 1303

GN 2426 1304

GN 2428 1305

3000 → PageGN 3490 1273

GN 3663 447

DIN 3670 189


Page 1418 Annexe - Otto Ganter GmbH & Co. KGPage 1424 | Modification standards s H11 / h11 d max. e...

Documents

Transcript of Page 1418 Annexe - Otto Ganter GmbH & Co. KGPage 1424 | Modification standards s H11 / h11 d max. e...