WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

10’

10’ Plan View

800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052

PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 1 - General Layout

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052

PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 2 - General Information

The Tool

Some sections of your display will beassembled with the supplied Hex Key Tool.

Typical Connection

Sections that require the Hex Key Tool for assembly are simple to join. Place the tool into the lockscrew and turn counter clockwise to loosen the lock. You will see the lock sections come together.Place the part into the adjoining extrusion groove where it should connect and turn the toolclockwise so the lock spreads apart while inside the groove. This completes a strong connection.

Typical Connection (cont’d)

Each extrusion contains a numbered label whichcorresponds with setup instructions. The label islocated within a groove of the extrusion (when possible).

Numbered Label

Horizontal sections will connect using thepre-installed camlock thumbscrew. Donot over tighten screw.

Vertical sections connect using verticalconnection bars with pre-installed twistknobs. Turn clockwise to tighten. Do notover tighten knobs.

Knob

Knob

Attach base place feet to vertical main supportsusing the bolt provided. The bolt is normallypre-installed into the bottom of the verticalsupport leg. Be careful not to strip the threads.

Using Your Setup Instructions

Cleaning and Packing Your Display

The Visionary Designs Setup Instructions are created specifically for yourconfiguration. They are laid out sequentially, including an exploded view ofthe entire display, and then a logical series of detailed steps to assemble themain structure and components. We encourage you to study the instructionsbefore attempting to assemble your exhibit.

Each page reminds you to tighten the setscrews after disassembling yourexhibit to prevent loss of the locks and setscrews (see below in RED).This is VERY IMPORTANT.

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.2) When cleaning laminate inserts or countertops, use mild cleansers and a soft material such as cotton.3) Keep all display components away from extreme heat and long exposure to sunlight to avoid warping and fading.4) Retain all packing material. It will make re-packing much easier and will reduce the likelihood of shipping damage.

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052

PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 3 - Backwall Assembly

Turn Knob Clockwiseto Tighten Lock

STAR indicates location of knobs on BACKSIDE of unit.

**Do not over tighten Knobs.**

Knob

Knob

GREEN STAR indicateslocation of connection

lock with knob.Set upper horizontal bars

[5a/5b] to be flush withindicated line before angled

top cap section

Horizontal Placement

3a

5a

Stopper

Item1232a3a

4a/4b5a/5b

DescriptionBase Plate42”h Lower Square Vertical Extrusion w/ A10 Clamps Attached42”h Upper Square Vertical Extrusion w/ A10 Clamps Attached42”h Lower Square Vertical Extrusion w/ A10 Clamps Attached42”h Upper Square Vertical Extrusion w/ A10 Clamps Attached45”w Horizontal Extrusion45”w Horizontal Extrusion

Qty.21111

1/11/1

Steps:1) Attach vertical extrusions [2] to base plates [1].2) Attach upper vertical extrusions [3 and 3a] to lower extrusions [2 and 2a] using connection bar [b].3) Connect horizontal extrusions [4a to 4b and 5a to 5b] together using connection bars [a].4) Attach horizontal assemblies [4a/4b and 5a/5b] between vertical assemblies as shown.5) Apply graphic via velcro to back of assembled backwall. Pull tight until velcro isn’t visible from front.6) Attach light to top of assembled backwall.

2a

3a

1

4a

1

2

3

5a

4b

5b

ConnectionBar

Slide Connection Barbetween Extrusionsand tighten Knobs

to secure.

ConnectionBar

Graphic AttachmentApply graphic to back

of assembled backwall.

ConnectionBar

a

a

bConnectionBar

b

A10 clam

ps attached to vertical extrusions for Wing A

ttachment

Light ConnectionAttach Lights toBackwall where desired and tighten in place.

A10 clam

ps attached to vertical extrusions for Wing A

ttachment

Stopper

Rear graphics velcro into positionto pre-installed loop velcro strips.

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052

PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 4 - Header Assembly

Item789

Description9.2856”h Vertical extrusion9.2856”h Vertical extrusion43.66”w Curved Horizontal Extrusion

Qty.111

Steps:1) Connect curved horizontal extrusion [9] between vertical extrusions [7 and 8].2) Attach assembled header to top of assebled backwall as shown.

**NOTE: Header must stay assembled when shipping

8

9

Lock header frame totop of assembled backwallusing supplied hex tool

Extrusion LockExtrusion Lock

Graphic AttachmentVelcro graphic to BACK ofassembled header frameafter connecting to main unit.Pull graphic tight until velcrois not visible from front.

7

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052

PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 5 - Wings/Counter

*Note: Curved extrusion[10] and horizontal [11]must stay assembledwhen shipping.

Item1010a1111a

Description30.2” Curved ExtrusionLeg Support12.184”w Horizontal ExtrusionFlange Plate

Qty.1111

Steps:1) attach assembled counter support [10/11] to vertical where indicated.2) Attach support leg [10a] to counter support [10/11].3) Attach flange plate [11a] to top of curved extrusion [10] as shown.4) Attach counter atop support, see counter top attachment detail.5) Attach wings to clamps as shown.

Counter Top AttachmentInsert screws located on undersideof counter into holes on flange plateand secure with wing nuts.

Wing Nut

Screw

10

11

11a

*

Monitor Mount Attachment V

4 Connectors

Attach monitor mount back plateto connectors using screws provided.

*

10a

Wings connect insidepre-installed clips.Each clip has a thumbscrewthat you tighten on the wing.Do not over tighten.

YOUR DISPLAY CURRENTLYDOES NOT INCLUDE A

MONITOR MOUNT

The literature holder connects toits support arm and to the backwallvertical using the supplied hex tool.You can position these items at any

location you wish. Use all 3 or just 1 or 2.

Top wing should alignwith main back wallhorizontal

Leaving about 3/4”gap between thetwo wings is recommended

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052

PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 6 - Forward Counter Part 1

Part NumberABCD

Step 1: A) Connect lower horizontal extrusion [C] between bottom of leg assemblies [A and B] as shown.B) Insert Laminated infill into grooves of leg assemblies [A and B].C) Attach extrusion door between leg assemblies [A and B] and atop laminated infill.D) Attach upper horizontal extrusion w/ door stopper [D] between leg assemblies [A and B], and set flush with top of legs [A and B].

DescriptionLeft Leg AssemblyRight Leg AssemblyHorizontal ExtrusionHoriontal Extrusion w/ Door Stopper

BlackKnob

Turn Knob Clockwiseto Tighten Lock

DOOR

Laminated Infill

A (left)B (right)

C

D (w/ Door Stopper)Knobs face INSIDE

of workstation

Knobs face INSIDEof workstation

Knobs face FORWARD

Pins are located on INSIDEFRONT vertical

of LegAssemblies

NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully engage, gently rock lock and extrusion back and forth while turning knob until lock fully opens.

Align with bottom of leg assemblies [A and B].

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052

PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 7 - Forward Counter Part 2

Part NumberEF

Step 2: A) Attach horizontal extrusion [E] between vertical leg assemblies [A and B] as shown below.B) Insert Laminated infill into grooves of vertical leg assemblies [A and B].C) Attach upper horizontal extrusion [F] between vertical leg assemblies [A and B] atop infill. D) Place internal shelf into assembled pedestal atop pins..E) Set Counter atop assembled pedestal and secure with Velcro straps attached to underside of top.

DescriptionHorizontal ExtrusionHorizontal Extrusion

E

LaminatedInfill

Knobs facing FORWARD

Place internal shelf into workstation then

place counter atopassembled workstation.

InternalShelf

F

Knobs face INSIDEof workstation

Bottom of counter has velcrostrip to fasten to main body fora more secure fit.

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052

PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 8 - Packing Part 1

Setup Hardware

Lights

Graphic

Case #1 Backwall Components

CounterTop

Base Plates

Backwall CounterSupport

Level 1 Level 2 Level 3

Wing PanelsA

ssem

bled

Hea

der a3

&3# snoi surt xE

a2&2# snoi surt x

E

Hor

izon

tal e

xtru

sion

s #4

a&4b

abd

5a&

5b

10a

Con

nect

ion

Bar

s A

Con

nect

ion

Bar

s B

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

800-676-3976 • 425-556-95114054 148th Ave. NE • Redmond, WA 98052

PACLEASE Hybrid Sacagawea VK-1222 Display Instructions / PAGE 9 - Packing Part 2

Level 1Level 2Level 3Level 4Level 5

Top View of each Level

Case #2 - Workstation Components

Counter

InternalShelf

Inserts

Door

Leg AssemblyB

Leg AssemblyA

Horiz. Extrusion E Horiz. Extrusion F

Hor

iz. E

xtru

sion

D

Hor

iz. E

xtru

sion

C

Con

nect

ion

Bar

for V

ertic

als