PACKAGE LINE-UP FOR RF AND MICROWAVE …...R50ZZ0001EJ0400 Rev.4.00 Page 1 of 74 Dec 11, 2012...

PACKAGES LINE-UP FOR RF AND MICROWAVE DEVICES

Rev.4.00 Dec 2012

Common Information

www.renesas.com

Notice 1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of

semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information.

2. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein.

3. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others.

4. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from such alteration, modification, copy or otherwise misappropriation of Renesas Electronics product.

5. Renesas Electronics products are classified according to the following two quality grades: “Standard” and “High Quality”. The recommended applications for each Renesas Electronics product depends on the product’s quality grade, as indicated below. “Standard”: Computers; office equipment; communications equipment; test and measurement equipment; audio and visual

equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots etc. “High Quality”: Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-

crime systems; and safety equipment etc. Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application for which it is not intended. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas Electronics.

6. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges.

7. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by you.

8. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations.

9. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. When exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations.

10. It is the responsibility of the buyer or distributor of Renesas Electronics products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products.

11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics.

12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries.

(Note 1) “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.

(Note 2) “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.

(2012.4)

R50ZZ0001EJ0400 Rev.4.00 Page 1 of 74 Dec 11, 2012

PACKAGES LINE-UP FOR RF AND MICROWAVE DEVICES Common Information

The mark <R> shows major revised points.

The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field.

CONTENTS

<Surface Mount Type Package Line-up Actual Size Illustrations> (1) Minimold·······················································································································································6 (2) LGA·······························································································································································6 (3) QFN·······························································································································································6 (4) SOP/SON and others ··································································································································6 <List of Surface Mount Type Package Drawings> List of Surface Mount Type Package Drawings ····························································································7 <List of Special Type Package Drawings> List of Special Type Package Drawings·········································································································9 <Package List> Package group general index························································································································10 Surface mount type 3-pin package list·········································································································11 Surface mount type 4-pin package list·········································································································12 Surface mount type 6-pin package list·········································································································13 Surface mount type 8, 10-pin package list···································································································14 Surface mount type 12, 14-pin package list·································································································15 Surface mount type 16-pin package list·······································································································16 Surface mount type 20-pin package list·······································································································17 Surface mount type 24, 28, 30, 32, 36-pin package list ··············································································18 Surface mount type 44, 52-pin package list·································································································19 Special type (Low Noise) 83A/83B, 84/84A/84C, S01, S02/S03 package list ············································20 Special type (Power 1/2) 75, 77, 79A, 95, 96/99 package list ·····································································20 Special type (Power 2/2) T-86M, T-91M (3M), T-92M, T-97M (3P), T-101M (3S), T-142M package list·····21 Special type (MCM, other) TO-92, 7-Pin Special, Chip package list ··························································21 <Package Dimensions> 3L2MM [3-Pin Lead-Less Minimold]··············································································································22 3MM (33 PKG) [3-Pin Minimold (33 PKG)] ····································································································22 3PMM (34 PKG) [3-Pin Power Minimold (34 PKG)]······················································································22 3SLM2 (M33, 0804 PKG) [3-Pin Super Lead-Less Minimold (M33, 0804 PKG)] ········································22

R50ZZ0001EJ0400Rev.4.00

Dec 11, 2012



3TL2MM (M53, T6J) [3-Pin Thin-Type Lead-Less Minimold (M53, T6J)]····················································23 3SMM [3-Pin Super Minimold] ·······················································································································23 3USMM (19, 1608 PKG) [3-Pin Ultra Super Minimold (19, 1608 PKG)] ······················································23 F3TUSMM [Flat-Lead 3-Pin Thin-Type Ultra Super Minimold] ···································································24 4L2MM (M14, 1208 PKG) [4-Pin Lead-Less Minimold (M14, 1208 PKG)]···················································24 4MM (39) [4-Pin Minimold (39)]······················································································································25 4PMM [4-Pin Power Minimold] ······················································································································25 4SMM (18) [4-Pin Super Minimold (18)] ········································································································25 F4TSMM (M04) [Flat-Lead 4-Pin Thin-Type Super Minimold (M04)] ··························································26 F4TSMM (M05, 2012 PKG) [Flat-Lead 4-Pin Thin-Type Super Minimold (M05, 2012 PKG)] ····················26 6LGA [6-Pin LGA (CSP Type)] ·······················································································································27 6L2MM (M16, 1208 PKG) [6-Pin Lead-Less Minimold (M16, 1208 PKG)]···················································28 6L2MM (1511 PKG) [6-Pin Lead-Less Minimold (1511 PKG)]·····································································28 6MM [6-Pin Minimold]·····································································································································28 6SLM2 (1007 PKG) [6-Pin Super Lead-Less Minimold (1007 PKG)] ··························································28 6SMM (M01, TB) [6-Pin Super Minimold (M01, TB)] ····················································································29 6TSMM [6-Pin Thin-Type Super Minimold] ··································································································29 F6TUSMM [Flat-Lead 6-Pin Thin-Type Ultra Super Minimold] ···································································29 6SON [6-Pin Plastic SON] ······························································································································30 6TSON (T5N) [6-Pin Plastic TSON (T5N)] ·····································································································31 6TSON (T6N) [6-Pin Plastic TSON (T6N)] ·····································································································31 6TSON (T6X) [6-Pin Plastic TSON (T6X)]······································································································32 6RTSON (T7C) [6-Pin Plastic RTSON (T7C)] ································································································32 6TSSON (T5K) [6-Pin Plastic TSSON (T5K)] ································································································33 6TSSON (T6R) [6-Pin Plastic TSSON (T6R)] ································································································34 8L2MM [8-Pin Lead-Less Minimold]··············································································································35 8SOP [8-Pin Plastic SOP (5.72 mm (225))] ···································································································35 8SSOP [8-Pin Plastic SSOP (4.45 mm (175))] ······························································································36 8TSON [8-Pin Plastic TSON]··························································································································36 10TSON (TQ) [10-Pin Plastic TSON (TQ)]·····································································································37 10TSSON (T6Q) [10-Pin Plastic TSSON (T6Q)] ····························································································38 10TSSOP [10-Pin Plastic TSSOP] ·················································································································38 12QFN (T5F) [12-Pin Plastic QFN (T5F)]·······································································································39 12QFN (T7K) [12-Pin Plastic QFN (T7K)] ······································································································40 12TQFN [12-Pin Plastic TQFN] ······················································································································41 12TSQFN (T5L) [12-Pin Plastic TSQFN (T5L)]······························································································42 12TSQFN (T6M) [12-Pin Plastic TSQFN (T6M)] ····························································································43 14LGA [14-Pin LGA (CSP Type)] ···················································································································44 14SOP [14-Pin Plastic SOP (5.72 mm (225))] ·······························································································45 14SSOP [14-Pin Plastic SSOP (5.72 mm (225))] ··························································································45 16QFN (T5T) [16-Pin Plastic QFN (T5T)]·······································································································46

<R>



16QFN (T6C) [16-Pin Plastic QFN (T6C)] ······································································································46 16QFN (T6S) [16-Pin Plastic QFN (T6S)] ······································································································47 16SSOP [16-Pin Plastic SSOP (5.72 mm (225))] ··························································································47 16HTSSOP [16-Pin Plastic HTSSOP] ············································································································48 16TSON [16-Pin Plastic TSON]······················································································································48 20QFN (0.4) [20-Pin Plastic QFN (0.4 mm pitch)]·························································································49 20RQFN (T5R) [20-Pin Plastic RQFN (T5R)]·································································································49 20QFN (0.5) (K) [20-Pin Plastic QFN (0.5 mm pitch) (K)] ············································································50 20QFN (0.5) (T7G) [20-Pin Plastic QFN (0.5 mm pitch) (T7G)]····································································51 20TQFN (T6E) [20-Pin Plastic TQFN (T6E)] ··································································································52 20LGA [20-Pin LGA (CSP Type)] ···················································································································53 20SOP [20-Pin Plastic SOP (7.62 mm (300))] ·······························································································54 20SSOP [20-Pin Plastic SSOP (5.72 mm (225))] ··························································································54 24QFN [24-Pin Plastic QFN]···························································································································55 24QFN (T7L) [24-Pin Plastic QFN (T7L)]·······································································································56 28QFN (K) [28-Pin Plastic QFN (K)]···············································································································57 28QFN (T7A) [28-Pin Plastic QFN (T7A)] ······································································································58 30SSOP [30-Pin Plastic SSOP (7.62 mm (300))] ··························································································59 32QFN (T5S) [32-Pin Plastic QFN (T5S)] ······································································································59 36QFN [36-Pin Plastic QFN]···························································································································60 44QFN [44-Pin Plastic QFN]···························································································································60 75 [75] ······························································································································································61 77 [77] ······························································································································································61 79A [79A] ·························································································································································61 83A, 83B [83A, 83B]········································································································································62 84, 84A, 84C [84, 84A, 84C]····························································································································62 95 [95] ······························································································································································62 96/99 [96/99] ····················································································································································62 S01 [S01]··························································································································································63 S02, S03 [S02, S03]·········································································································································64 T-86M [T-86M]··················································································································································65 T-91M (3M) [T-91M (3M)]·································································································································65 T-92M [T-92M]··················································································································································65 T-97M (3P) [T-97M (3P)]··································································································································66 T-101M (3S) [T-101M (3S)]······························································································································66 T-142M [T-142M]··············································································································································66 TO-92 [TO-92] ··················································································································································67 7-Pin Special [7-Pin Special With Heatsink] ································································································68 <Mounting Pad Layout> 3L2MM [3-Pin Lead-Less Minimold]··············································································································69

<R>



3MM (33 PKG) [3-Pin Minimold (33 PKG)] ····································································································69 3PMM (34 PKG) [3-Pin Power Minimold (34 PKG)]······················································································69 3SLM2 (M33, 0804 PKG) [3-Pin Super Lead-Less Minimold (M33, 0804 PKG)] ········································69 3TL2MM (M53, T6J) [3-Pin Thin-Type Lead-Less Minimold (M53, T6J)]····················································69 3SMM [3-Pin Super Minimold] ·······················································································································69 3USMM (19, 1608 PKG) [3-Pin Ultra Super Minimold (19, 1608 PKG)] ······················································69 F3TUSMM [Flat-Lead 3-Pin Thin-Type Ultra Super Minimold] ···································································69 4L2MM (M14, 1208 PKG) [4-Pin Lead-Less Minimold (M14, 1208 PKG)]···················································69 4MM (39) [4-Pin Minimold (39)]······················································································································70 4PMM [4-Pin Power Minimold] ······················································································································70 4SMM (18) [4-Pin Super Minimold (18)] ········································································································70 F4TSMM (M04) [Flat-Lead 4-Pin Thin-Type Super Minimold (M04)] ··························································70 F4TSMM (M05, 2012 PKG) [Flat-Lead 4-Pin Thin-Type Super Minimold (M05, 2012 PKG)] ····················70 6L2MM (M16, 1208 PKG) [6-Pin Lead-Less Minimold (M16, 1208 PKG)]···················································70 6L2MM (1511 PKG) [6-Pin Lead-Less Minimold (1511 PKG) for Silicon MMIC/GaAs MMIC] ··················70 6MM [6-Pin Minimold]·····································································································································70 6SLM2 (1007 PKG) [6-Pin Super Lead-Less Minimold (1007 PKG)] ··························································70 6SMM (M01, TB) [6-Pin Super Minimold (M01, TB)] ····················································································71 6TSON [6-Pin Plastic TSON]··························································································································71 6TSSON (T5K) [6-Pin Plastic TSSON (T5K)] ································································································71 6TSSON (T6R) [6-Pin Plastic TSSON (T6R)] ································································································71 F6TUSMM [Flat-Lead 6-Pin Thin-Type Ultra Super Minimold] ···································································71 8L2MM [8-Pin Lead-Less Minimold]··············································································································71 8SSOP [8-Pin Plastic SSOP (4.45 mm (175))] ······························································································71 8TSON [8-Pin Plastic TSON]··························································································································71 10TSON [10-Pin Plastic TSON]······················································································································71 10TSSON [10-Pin Plastic TSSON]·················································································································72 12QFN [12-Pin Plastic QFN]···························································································································72 12QFN (T7K) [12-Pin Plastic QFN (T7K)] ······································································································72 12TQFN [12-Pin Plastic TQFN] ······················································································································72 12TSQFN (T5L) [12-Pin Plastic TSQFN (T5L)]······························································································72 12TSQFN (T6M) [12-Pin Plastic TSQFN (T6M)] ····························································································72 14LGA [14-Pin LGA (CSP Type)] ···················································································································72 14SSOP [14-Pin Plastic SSOP (5.72 mm (225))] ··························································································72 16QFN (T5T/T6S) [16-Pin Plastic QFN (T5T/T6S)]························································································72 16QFN (T6C) [16-Pin Plastic QFN (T6C)] ······································································································73 16SSOP [16-Pin Plastic SSOP (5.72 mm (225))] ··························································································73 20SSOP [20-Pin Plastic SSOP (5.72 mm (225))] ··························································································73 20QFN (0.4) [20-Pin Plastic QFN (0.4 mm pitch)]·························································································73 20QFN (0.5) (T7G) [20-Pin Plastic QFN (0.5 mm pitch) (T7G)]····································································73 20RQFN [20-Pin Plastic RQFN] ·····················································································································73

<R>



24QFN [24-Pin Plastic QFN]···························································································································73 24QFN (T7L) [24-Pin Plastic QFN (T7L)]·······································································································73 28QFN (K) [28-Pin Plastic QFN (K)]···············································································································73 28QFN (T7A) [28-Pin Plastic QFN (T7A)] ······································································································74 79A [79A] ·························································································································································74 S01 [S01] ····························································································································· 74

<R>



Surface Mount Type Package Line-up Actual Size Illustrations (Unit : mm, Size not exact)

(1) Minimold

1st Gene.

3pins

SLM2L2MM

TUSMMTSMM2012.5

TSMMUSMM1608

SMM2012.5

MM2915

PMM

4pins

6pins

8pins

2nd 3rd

0804

1005

1408

L2MM1511(IC)

(IC)2020

TUSMM1511

L2MM1208

L2MM1208

SLM21007

(IC )

TUTSMM

TL2MM1210

(2) LGA

LGA6pin 1.5 ×1.5

T5B

14pin 2.5 × 2.5

T5D

20pin 3.0 × 3.0

T5E

10pin 2.0 × 2.1

T5C

(3) QFN

QFN(0.4pitch)

QFN(0.5pitch)

20pin4 ×3

K

36pin6 ×6

K

44pin6 ×6

K

52pin7 ×7

KT5S

32pin5 ×5

T5F

12pin3 ×3

T7K

12pin2 ×2

24pin5 ×4

K

28pin5.1 ×4.7

K

20pin3.8 ×3.8

KT5L/T6M

12pin2 ×2

T5T

16pin3 ×3

T5J

12pin2.5 ×2.5

20pin3.5 ×2.5

T5R

20pin3.5 ×3.5

T6E

28pin5 ×5

T7A

20pin4 ×4

T7G

24pin4 ×4

T7L

(4) SOP/SON and others

HTSSOP

16pin 5.2 ×4.4 20pin 6.7 ×4.4 30pin 9.9 ×6.1

TSON

SON

SSOP8pin 2.9 ×3.2

8pin 5.4 ×4.4SOP

GV

G

GR GR GS

14pin 5.4 ×4.4

TQ

14pin 10.2 ×4.4

G

20pin 12.7 ×5.6

GS

16pin 5.5 ×5.2

GR

6pin 3.0 × 2.0

T5G

TSSON

TSSOP10pin 2.8 × 2.2

TH

10pin 2.6 ×2.4

TQ

16pin 3.3 ×2.3

T5A

6pin 1.5 ×1.5

T5N/T6N6pin 1.0 ×1.0

T5K

10pin 2.0 ×1.4

T6Q

8pin 1.5 ×1.5

T6Z

6pin 2.0 ×1.3

T7C

<R>



List of Surface Mount Type Package Drawings (1/2) (Magnification of Dimensions × 2.5)

Abbreviation 3MM 3SMM 3USMM F3TUSMM 3TL2MM 3L2MM Outline Cliagram and Outline Dimensions L × W × H (mm)

(2.9 × 1.5 × 1.1)

(2.0 × 1.3 × 0.9)

(1.6 × 0.8 × 0.8)

(1.4 × 0.8 × 0.6)

(1.2 × 1.0 × 0.3)

(1.0 × 0.7 × 0.5)

Abbreviation 3SLM2 3PMM (34 PKG) 4MM 4SMM F4TSMM 4L2MM Outline Cliagram and Outline Dimensions L × W × H (mm)

(0.8 × 0.4 × 0.4)

(Bottom View)

(4.5 × 2.5 × 1.5)

(2.9 × 1.5 × 1.1)

(2.0 × 1.3 × 0.9)

(2.0 × 1.3 × 0.6)

(1.2 × 0.8 × 0.5)

Abbreviation 4PMM 6MM 6SMM 6TSMM 6L2MM (1511) F6TUSMM Outline Cliagram and Outline Dimensions L × W × H (mm)

(Bottom View)

(4.5 × 2.5 × 1.5)

(2.9 × 1.5 × 1.1)

(2.0 × 1.3 × 0.9)

(2.0 × 1.3 × 0.6)

(1.5 × 1.1 × 0.6)

(1.5 × 1.1 × 0.6)

Abbreviation 6L2MM (1208) 6SLM2 6LGA 6SON 6RTSON 6TSON Outline Cliagram and Outline Dimensions L × W × H (mm)

(1.2 × 0.8 × 0.5)

(1.0 × 0.7 × 0.4)

(Bottom View)

(1.5 × 1.5 × 0.6)

(Bottom View)

(3.0 × 2.0 × 0.8)

(Bottom View)

(2.0 × 1.3 × 0.4)

(Bottom View)

(1.5 × 1.5 × 0.4)

Abbreviation 6TSSON 8SOP 8SSOP 8L2MM 8TSON Outline Cliagram and Outline Dimensions L × W × H (mm)

(Bottom View)

(1.0 × 1.0 × 0.4)

(5.2 × 4.4 × 1.6)

(2.9 × 3.2 × 1.6)

(Bottom View)

(2.0 × 2.0 × 0.5)

(Bottom View)

(1.5 × 1.5 × 0.4)



List of Surface Mount Type Package Drawings (2/2) (Magnification of Dimensions × 2.5)

Abbreviation 10TSSOP 10TSON 10TSSON 12QFN 12QFN(T7K) 12TQFN Outline Cliagram and Outline Dimensions L × W × H (mm)

(2.8 × 2.2 × 1.1)

(2.6 × 2.4 × 0.6)

(Bottom View)

(2.0 × 1.4 × 0.4)

(Bottom View)

(3.0 × 3.0 × 0.8)

(Bottom View)

(2.0 × 2.0 × 0.6)

(Bottom View)

(2.5 × 2.5 × 0.4)

Abbreviation 12TSQFN 14SOP 14SSOP 14LGA 16HTSSOP Outline Cliagram and Outline Dimensions L × W × H (mm)

(Bottom View)

(2.0 × 2.0 × 0.4) (10.2 × 4.4 × 1.6)

(5.4 × 4.4 × 1.6)

(Bottom View)

(2.5 × 2.5 × 0.6)

(Bottom View)

(5.5 × 5.2 × 0.9)

Abbreviation 16QFN 16SSOP 16TSON 20SOP 20SSOP Outline Cliagram and Outline Dimensions L × W × H (mm)

(Bottom View)

(3.0 × 3.0 × 0.8)

(5.2 × 4.4 × 1.6)

(Bottom View)

(3.3 × 2.3 × 0.6)

(12.7 × 5.6 × 1.7)

(6.7 × 4.4 × 1.6)

Abbreviation 20QFN (0.4) 20QFN (0.5)(K) 20QFN (0.5) (T7G) 20TQFN 20RQFN Outline Cliagram and Outline Dimensions L × W × H (mm)

(4.0 × 3.0 × 0.9)

(3.8 × 3.8 × 0.9)

(4 × 4 × 0.6)

(Bottom View)

(3.5 × 3.5 × 0.6)

(Bottom View)

(3.5 × 2.5 × 0.6)

Abbreviation 20LGA 24QFN 24QFN(T7L) 28QFN (K) 28QFN (T7A) Outline Cliagram and Outline Dimensions L × W × H (mm)

(Bottom View)

(3.0 × 3.0 × 0.6)

(5.0 × 4.0 × 1.0)

(Bottom View)

(4 × 4 × 0.6)

(5.1 × 4.7 × 1.0)

(5.0 × 5.0 × 0.7)

Abbreviation 30SSOP 32QFN 36QFN 44QFN Outline Cliagram and Outline Dimensions L × W × H (mm)

(9.9 × 6.1 × 1.8)

(Bottom View)

(5.0 × 5.0 × 0.9)

(6.0 × 6.0 × 1.0)

(6.0 × 6.0 × 1.0)

<R>

<R>



List of Special Type Package Drawings (1/2) (Magnification of Dimensions × 1.5)

Abbreviation 75 77 79A 83A, 83B Outline Cliagram and Outline Dimensions L × W × H (mm)

(9.8 × 2.7 × 2.3)

(17.5 × 6.4 × 3.8)

(4.4 × 4.2 × 0.9)

(1.9 × 1.9 × 1.6)

Abbreviation 84, 84A, 84C 95 96/99 S01 S02, S03 Outline Cliagram and Outline Dimensions L × W × H (mm)

(1.8 × 1.8 × 1.8) (18.5 × 5.9 × 4.5) (15.0 × 4.3 × 5.0)

(2.0 × 2.0 × 1.5)

(2.6 × 2.6 × 1.5)

List of Special Type Package Drawings (2/2) (Magnification of Dimensions × 1.0)

Abbreviation T-86M T-91M (3M) T-92M T-97M (3P) Outline Cliagram and Outline Dimensions L × W × H (mm)

(24.5 × 11.4 × 4.9)

(20.3 × 5.8 × 4.2) (35.2 × 17.4 × 6.0)

(34.0 × 9.9 × 4.4)

Abbreviation T-101M (3S) T-142M TO-92 7-Pin Special Outline Cliagram and Outline Dimensions L × W × H (mm)

(41.2 × 10.2 × 5.0) (24.0 × 17.4 × 5.7)

(5.5 × 5.2 × 4.2)

(45.1 × 14.9 × 21.5)



Package List

Package group general index Type Group Abbreviation

3-pin 3MM, 3SMM, 3USMM, F3TUSMM, 3L2MM, 3TL2MM, 3SLM2, 3PMM 4-pin 4MM, 4SMM, F4TSMM, 4L2MM, 4PMM 6-pin 6MM, 6SMM, 6TSMM, 6SLM2, 6L2MM, F6TUSMM, 6LGA, 6SON,

6TSON, 6RTSON, 6TSSON 8-pin 8SOP, 8SSOP, 8L2MM, 8TSON 10-pin 10TSSOP, 10TSON, 10TSSON, 10LGA 12-pin 12QFN, 12TQFN, 12TSQFN 14-pin 14SOP, 14SSOP, 14LGA 16-pin 16HTSSOP, 16QFN, 16SSOP, 16TSON 20-pin 20SOP, 20SSOP, 20QFN, 20TQFN, 20RQFN, 20LGA 24 to 36-pin 24QFN, 28QFN, 30SSOP, 32QFN, 36QFN

Surface mount type

44, 52-pin 44QFN, 52QFN Low Noise 83A, 83B, 84, 84A, 84C, S01, S02, S03 Power 1/2 75, 77, 79A, 95, 96/99 Power 2/2 T-86M, T-91M (3M), T-92M, T-97M (3P), T-101M (3S), T-142M

Special type

MCM, other TO-92, 7-Pin Special, Chip



Surface mount type 3-pin package list Abbreviation 3MM (33) 3SMM 3USMM F3TUSMM 3L2MM Outline Cliagramand Outline Dimensions L × W × H (mm) Magnification of Dimensions × 3.5

(2.9 × 1.5 × 1.1)

(2.0 × 1.3 × 0.9)

(1.6 × 0.8 × 0.8)

(Top View)

(Bottom View)

(1.4 × 0.8 × 0.6)

(Top View)

(Bottom View)

(1.0 × 0.7 × 0.5)

Abbreviation 3TL2MM 3SLM2 (0804) 3PMM (34) Outline Cliagramand Outline Dimensions L × W × H (mm) Magnification of Dimensions × 3.5

(Top View)

(Bottom View)

(1.2 × 1.0 × 0.3)

(Top View)

(Bottom View)

(0.8 × 0.4 × 0.4)

(Top View) (Bottom View)

(4.5 × 2.5 × 1.5)

Abbreviation Package Code Package Name Drawings

NE IC Package Land Pattern

3MM 3SMM 3USMM F3TUSMM 3L2MM 3TL2MM 3SLM2 3PMM

33 30 19 M03 M13 M53 M33 34

T6J

3-Pin Minimold (33 PKG) 3-Pin Super Minimold 3-Pin Ultra Super Minimold (1608 PKG) Flat-Lead 3-Pin Thin-Type Ultra Super Minimold 3-Pin Lead-Less Minimold 3-Pin Thin-Type Lead-Less Minimold 3-Pin Super Lead-Less Minimold (0804 PKG) 3-Pin Power Minimold (34 PKG)



Surface mount type 4-pin package list Abbreviation 4MM 4SMM F4TSMM (2012)

Outline Cliagram and Outline Dimensions L × W × H (mm) Magnification of Dimensions × 3.5

(2.9 × 1.5 × 1.1)

(2.0 × 1.3 × 0.9)

(Top View)

(Bottom View)

(2.0 × 1.3 × 0.6)

Abbreviation 4L2MM (1208) 4PMM Outline Cliagram and Outline Dimensions L × W × H (mm) Magnification of Dimensions × 3.5

(Top View)

(Bottom View)

(1.2 × 0.8 × 0.5)


(4.5 × 2.5 × 1.5)

Abbreviation Package Code Package Name Drawings NE IC Package Land Pattern4MM 4SMM F4TSMM F4TSMM 4L2MM 4PMM

39 18 M04 M05 M14 M02

4-Pin Minimold (39) 4-Pin Super Minimold (18) Flat-Lead 4-Pin Thin-Type Super Minimold Flat-Lead 4-Pin Thin-Type Super Minimold (2012 PKG) 4-Pin Lead-Less Minimold (1208 PKG) 4-Pin Power Minimold



Surface mount type 6-pin package list Abbreviation 6MM 6SMM 6TSMM 6L2MM (1511) F6TUSMM


(2.9 × 1.5 × 1.1)

(2.0 × 1.3 × 0.9)

(2.0 × 1.3 × 0.6)

(Top View)

(Bottom View)

(1.5 × 1.1 × 0.6)

(Top View)

(Bottom View)

(1.5 × 1.1 × 0.6)

Abbreviation 6L2MM (1208) 6SLM2 (1007) 6LGA Outline Cliagram and Outline Dimensions L × W × H (mm) Magnification of Dimensions × 5.0

(Top View)

(Bottom View)

(1.2 × 0.8 × 0.5)

(Top View)

(Bottom View)

(1.0 × 0.7 × 0.4)


(1.5 × 1.5 × 0.6) Abbreviation 6SON 6TSON 6RTSON 6TSSON



(3.0 × 2.0 × 0.8)


(1.5 × 1.5 × 0.4)

(Top View)

(Bottom View)

(2.0 × 1.3 × 0.4)

(Top View)

(Bottom View)

(1.0 × 1.0 × 0.4)



6MM 6MM 6SMM 6SMM 6TSMM 6SLM2 6L2MM F6TUSMM 6L2MM 6LGA 6SON 6TSON 6TSON 6TSON 6RTSON 6TSSON 6TSSON

M01 M16

T TA T Note TB TF Note TS Note TK TC Note TD Note T5B T5G T5N T6N T6X T7C T5K T6R

6-Pin Minimold 6-Pin Minimold 6-Pin Super Minimold 6-Pin Super Minimold 6-Pin Thin-Type Super Minimold 6-Pin Super Lead-Less Minimold (1007 PKG) 6-Pin Lead-Less Minimold (1511 PKG) Flat-Lead 6-Pin Thin-Type Ultra Super Minimold 6-Pin Lead-Less Minimold (1208 PKG) 6-pin LGA (CSP Type) 6-Pin Plastic SON 6-Pin Plastic TSON (T5N) 6-Pin Plastic TSON (T6N) 6-Pin Plastic TSON (T6X) 6-Pin Plastic RTSON (T7C) 6-Pin Plastic TSSON (T5K) 6-Pin Plastic TSSON (T6R)

−

− −

− −

Note: Twin Transistor



Surface mount type 8, 10-pin package list Abbreviation 8SOP 8SSOP 8L2MM 8TSON


(5.2 × 4.4 × 1.6)

(2.9 × 3.2 × 1.6)

(Top View)

(Bottom View)

(2.0 × 2.0 × 0.5)

(Top View)

(Bottom View)

(1.5 × 1.5 × 0.4)

Abbreviation 10TSSOP 10TSON 10TSSON 10LGA Outline Cliagram and Outline Dimensions L × W × H (mm) Magnification of Dimensions × 3.5

(2.8 × 2.2 × 1.1)

(Top View)

(Bottom View)

(2.6 × 2.4 × 0.6)

(Top View)

(Bottom View)

(2.0 × 1.4 × 0.4)

(Top View)

(Bottom View)

(2.0 × 2.1 × 0.6)



8SOP 8SSOP 8L2MM 8TSON 10TSSOP 10TSON 10TSSON 10LGA

G, GR GV TU T6Z TH TQ T6Q T5C

8-Pin Plastic SOP (5.72 mm (225)) 8-Pin Plastic SSOP (4.45 mm (175)) 8-Pin Lead-Less Minimold 8-Pin Plastic TSON 10-Pin Plastic TSSOP 10-Pin Plastic TSON 10-Pin Plastic TSSON 10-Pin LGA

−

−

−

−



Surface mount type 12, 14-pin package list Abbreviation 12QFN 12QFN(T7K) 12TQFN 12TSQFN


(Top View)

(Bottom View)

(3.0 × 3.0 × 0.8)

(Top View)

(Bottom View)

(2.0 × 2.0 × 0.6)

(Top View)

(Bottom View)

(2.5 × 2.5 × 0.4)

(Top View)

(Bottom View)

(2.0 × 2.0 × 0.4)

Abbreviation 14SOP 14SSOP 14LGA Outline Cliagram and Outline Dimensions L × W × H (mm) Magnification of Dimensions × 4.0

(10.2 × 4.4 × 1.6)

(5.4 × 4.4 × 1.6)

(Top View)

(Bottom View)

(2.5 × 2.5 × 0.6)



12QFN 12QFN 12TQFN 12TSQFN 12TSQFN 14SOP 14SSOP 14LGA

T5F T7K T5J T5L T6M G, GR GR T5D

12-Pin Plastic QFN 12-Pin Plastic QFN (T7K) 12-Pin Plastic TQFN 12-Pin Plastic TSQFN (T5L) 12-Pin Plastic TSQFN (T6M) 14-Pin Plastic SOP (5.72 mm (225)) 14-Pin Plastic SSOP (5.72 mm (225)) 14-Pin LGA (CSP Type)

−

<R>

<R>



Surface mount type 16-pin package list Abbreviation 16HTSSOP 16QFN 16SSOP 16TSON



(5.5 × 5.2 × 0.9)


(3.0 × 3.0 × 0.8)

(5.2 × 4.4 × 1.6)

(Top View)

(Bottom View)

(3.3 × 2.3 × 0.6)



16HTSSOP 16QFN 16QFN 16QFN 16SSOP 16TSON

GR GR T5T T6C T6S GR T5A

16-Pin Plastic HTSSOP 16-Pin Plastic QFN (T5T) 16-Pin Plastic QFN (T6C) 16-Pin Plastic QFN (T6S) 16-Pin Plastic SSOP (5.72 mm (225)) 16-Pin Plastic TSON

−

−



Surface mount type 20-pin package list Abbreviation 20SOP 20SSOP 20QFN (0.4) 20QFN (0.5) (K)


(12.7 × 5.6 × 1.7)

(6.7 × 4.4 × 1.6)

(Top View)

(Bottom View)

(4.0 × 3.0 × 0.9)

(Top View)

(Bottom View)

(3.8 × 3.8 × 0.9)Abbreviation 20QFN (0.5) (T7G) 20TQFN 20RQFN 20LGA


(Top View)

(Bottom View)

(4.0 × 4.0 × 0.6)

(Top View)

(Bottom View)

(3.5 × 3.5 × 0.6)

(Top View)

(Bottom View)

(3.5 × 2.5 × 0.6)

(Top View)

(Bottom View)

(3.0 × 3.0 × 0.6)

Abbreviation Package Code Package Name Drawings NE IC Package Land Pattern

20SOP 20SSOP 20QFN (0.4) 20QFN (0.5) 20QFN (0.5) 20TQFN 20RQFN 20LGA

GS GR K K T7G T6E T5R T5E

20-Pin Plastic SOP (7.62 mm (300)) 20-Pin Plastic SSOP (5.72 mm (225)) 20-Pin Plastic QFN (0.4 mm pitch) 20-Pin Plastic QFN (0.5 mm pitch) 20-Pin Plastic QFN (0.5 mm pitch) 20-Pin Plastic TQFN 20-Pin Plastic RQFN 20-Pin LGA

−

−

−

−



Surface mount type 24, 28, 30, 32, 36-pin package list Abbreviation 24QFN 24QFN(T7L) 28QFN (K) 28QFN (T7A)


(Top View)

(Bottom View)

(5.0 × 4.0 × 1.0)

(Top View)

(Bottom View)

(4.0 × 4.0 × 0.6)

(Top View)

(Bottom View)

(5.1 × 4.7 × 1.0)

(Top View)

(Bottom View)

(5.0 × 5.0 × 0.7)

Abbreviation 30SSOP 32QFN 36QFN Outline Cliagram and Outline Dimensions L × W × H (mm) Magnification of Dimensions × 3.0

(9.9 × 6.1 × 1.8)

(Top View)

(Bottom View)

(5.0 × 5.0 × 0.9)

(Top View)

(Bottom View)

(6.0 × 6.0 × 1.0)



24QFN 24QFN 28QFN 28QFN 30SSOP 32QFN 36QFN

K T7L K T7A GS T5S K

24-Pin Plastic QFN 24-Pin Plastic QFN (T7L) 28-Pin Plastic QFN (K) 28-Pin Plastic QFN (T7A) 30-Pin Plastic SSOP (7.62 mm (300)) 32-Pin Plastic QFN 36-Pin Plastic QFN

− − −

<R>

<R>



Surface mount type 44, 52-pin package list Abbreviation 44QFN 52QFN


(Top View)

(Bottom View)

(6.0 × 6.0 × 1.0)

(Top View)

(Bottom View)

(7.0 × 7.0 × 1.0)



44QFN 52QFN

K K

44-Pin Plastic QFN 52-Pin Plastic QFN

−

− −



Special type (Low Noise) 83A/83B, 84/84A/84C, S01, S02/S03 package list Abbreviation 83A, 83B 84, 84A, 84C S01 S02, S03


(1.9 × 1.9 × 1.6)

(1.8 × 1.8 × 1.8)

(2.0 × 2.0 × 1.5)

(2.6 × 2.6 × 1.5) Abbreviation Package Code Package Name Drawings


83A/83B 84/84A/84C S01 S02/S03

83A/83B 84/84A/84CS01 S02/S03

83A/83B Ceramic Package 84/84A/84C Ceramic Package S01 Hollow Plastic Mold Package S02/S03 Hollow Plastic Mold Package

− −

−

Special type (Power 1/2) 75, 77, 79A, 95, 96/99 package list Abbreviation 75 77 79A


(9.8 × 2.7 × 2.3)

(17.5 × 6.4 × 3.8)

(4.4 × 4.2 × 0.9) Abbreviation 95 96/99


(18.5 × 5.9 × 4.5)

(15.0 × 4.3 × 5.0)


75 77 79A 95 96/99

75 77 79A 95 96/99

75 Ceramic Package 77 Ceramic Package 79A Plastic Mold Package 95 Ceramic Package 96/99 Ceramic Package

− −

− −



Special type (Power 2/2) T-86M, T-91M (3M), T-92M, T-97M (3P), T-101M (3S), T-142M package list Abbreviation T-86M T-91M (3M) T-92M Outline Cliagram and Outline Dimensions L × W × H (mm) Magnification of Dimensions × 1.0

(24.5 × 11.4 × 4.9)

(20.3 × 5.8 × 4.2)

(35.2 × 17.4 × 5.7) Abbreviation T-97M (3P) T-101M (3S) T-142M Outline Cliagram and Outline Dimensions L × W × H (mm) Magnification of Dimensions × 1.0

(34.0 × 9.9 × 4.4)

(41.2 × 10.2 × 5.0)

(24.0 × 17.4 × 5.7)


T-86M T-91M T-92M T-97M T-101M T-142M

3M 3P 3S

T-86M Hollow Plastic Mold Package T-91M Hollow Plastic Mold Package T-92M Hollow Plastic Mold Package T-97M Hollow Plastic Mold Package T-101M Hollow Plastic Mold Package T-142M Hollow Plastic Mold Package

− − − − − −

Special type (MCM, other) TO-92, 7-Pin Special, Chip package list Abbreviation TO-92 7-Pin Special Chip


(5.5 × 5.2 × 4.2) (45.1 × 14.9 × 21.5)

The Chip size drawing is carried to the data sheet.



TO-92 7-Pin Special Chip

32 00

TO-92 Plastic Mold Package 7-Pin Special With Heatsink Chip

−

− − −



Package Dimensions (1/47)

(Unit : mm)

3-Pin Lead-Less Minimold 3-Pin Minimold (33 PKG)

3-Pin Power Minimold (34 PKG) 3-Pin Super Lead-Less Minimold (M33, 0804 PKG)

2.8±0.2

1.5

2

1 32.9±

0.2 0.

950.

95

0.4+

0.1

–0

.05

0.4+

0.1

–0

.05

0.65+0.1 –0.15

0.16

+0.

1

–0.0

5

0.3

0 to

0.1

1.1

to 1

.4

Marking

1.5±0.1

0.41+0.03–0.06

4.5±0.1

0.42±0.060.42±0.06

1.6±0.2

3.0

1.5

21 3 2.

5±0.

1

4.0±

0.25

0.8

MIN

.

0.47±0.06

0.12

5+0.

1

–0.0

5

0.5±

0.05

0.10.1

0.2+

0.1

–0

.05

0.35

0.7

0.35

0.15

+0.

1

–0.0

50.

15+

0.1

–0

.05

1.0+

0.1

–0

.05

0.5+0.1 –0.05

0.7±0.05

1

2 3

0.3

0.2 0.2

(Bottom View)

0.15

0.57 0.

285

0.12

5

0.44±0.05

1

2 3

(Bottom View)

0.15

0.84

±0.

05

0.12

5

0.15

0.64±0.05

0.11

0.4

MA

X.




(Unit : mm)

3-Pin Ultra Super Minimold (19, 1608 PKG)

0.75

±0.

05

0.6

0 to

0.1

0.15

+0.

1

–0.0

5

1.6±

0.1

1.0

0.5

0.5

0.3+

0.1

–0

1.6±0.1

0.8±0.1

0.2+

0.1

–0

1

2

3

3-Pin Super Minimold

0.9±

0.1

0.3

0.15

+0.

1

–0.0

5

0 to

0.1

Marking

2.0±

0.2

0.65

0.65

0.3+

0.1

–0

0.3+

0.1

–0 1

2

3

2.1±0.1

1.25±0.1

3-Pin Thin-Type Lead-Less Minimold (M53, T6J)

0.11

+0.

1

–0.0

5

MA

X. 0

.33

0.30

+0.

1

–0.0

5

(0.8

)0.

15+

0.1

–0

.05

0.15

+0.

1

–0.0

5

1.2±

0.05

1.0±0.1

1.2±0.1

2

1 3

(0.8)

(0.2) (0.2)

(Bottom View)




(Unit : mm)

4-Pin Lead-Less Minimold (M14, 1208 PKG)

Flat-Lead 3-Pin Thin-Type Ultra Super Minimold0.

59 ±

0.0

5

0.15

+0.

1

–0.0

5

1.2 ± 0.05

0.8 ± 0.1

1.4

± 0

.1

(0.9

) 0.45

0.45

0.3+

0.1

–0

1

3

2

0.2+

0.1

–0

0.5±

0.05

0.11

+0.

1

–0.0

5

0.6

0.2

1.2+

0.07

–0.0

5

0.8

0.8+0.07–0.05

1.0±0.05

0.15

±0.

05

43

12

0.1

(Bottom View)(Top View)




(Unit : mm)

4-Pin Super Minimold (18)

0.9±

0.1

0.15

+0.

1

–0.0

5

0.3

0 to

0.1

3

1.30

2.0±

0.2

1.25

0.65

0.60

4

21

2.1±0.2

1.25±0.1

0.65

0.65

0.4+

0.1

–0

.05

0.3+

0.1

–0

.05

0.3+

0.1

–0

.05

0.3+

0.1

–0

.05

1.5±0.1

0.25±0.02

4.5±0.1

2.1

1.6

0.8

0.42±0.060.42±0.06

0.3

2.45

±0.

1

0.1

0.8

MIN

.

3.95

±0.

25

0.46±0.06

3.0

1.5

0.851.

55

E B

C

E

4-Pin Power Minimold4-Pin Minimold (39)

2.9±

0.2

(1.8

)

(1.9

)0.95

21

34

0.85

0.6+

0.1

–0

.06

0.4+

0.1

–0

.05

0.4+

0.1

–0

.05

0.4+

0.1

–0

.05

2.8+0.2–0.3

1.5+0.2–0.1

5˚ 5˚

0.8

0.16

+0.

1

–0.0

6

0 to

0.1

1.1+

0.2

–0.1

5˚ 5˚




(Unit : mm)

Flat-Lead 4-Pin Thin-Type Super Minimold (M04)

0.59

±0.

05

0.11

+0.

1

–0.0

5

(Bottom View)

43

12

1.25

2.0±

0.1

1.30

(1.05)

0.60

0.65

0.65

0.65

1.30

1.25

2.0±

0.1

12

43

1.25±0.1

2.05±0.10.

30+

0.1

–0

.05

0.40

+0.

1

–0.0

5

0.30

+0.

1

–0.0

50.

30+

0.1

–0

.05

Flat-Lead 4-Pin Thin-Type Super Minimold (M05, 2012 PKG)

0.59

±0.

05

0.11

+0.

1

–0.0

5

(Bottom View)

(0.6

5)0.

65

1.30

2.0±

0.1

43

12

1.25±0.1

2.05±0.1

0.30

+0.

1

–0.0

5

(Top View)

Remark ( ) : Reference value

0.5

(1.05)




(Unit : mm)

6-Pin LGA (CSP Type)

1.5±0.1

1.5±

0.1

(Top View)

0+0.03 –0

0.6

MA

X.

(Bottom View)

0.5±0.05

(0.75)

(0.3

)(0

.3)

(0.4

5)(0

.45)

(0.4

)

(0.275) 0+0.1 –0

(0.1

)

0.3±0.05

Through hole

Solder resist




(Unit : mm)

6-Pin Lead-Less Minimold (M16, 1208 PKG)0.

5±0.

05

0.12

5+0.

1

–0.0

5

0.4

0.4

0.8

0.15

±0.

05

1.2+

0.07

–0.0

5

0.8+0.07–0.05

1.0±0.05

12

3

65

4

6-Pin Minimold

2.9±

0.2 0.95

0.95

1.9

4 3

5 2

6 1

0.3+

0.1

–0

.05

2.8+0.2–0.3

1.5+0.2–0.1

0.8

0.13

±0.

11.1+

0.2

–0.1

0 to

0.1

0.2 MIN.

6-Pin Super Lead-Less Minimold (1007 PKG)

0.4

MA

X.

0.11

+0.

1

–0.0

5

0.35

0.35

0.7

0.12

5±0.

05

1.0±

0.05

0.7±0.05

0.9±0.05

12

3

65

4

6-Pin Lead-Less Minimold (1511 PKG)

0.48

±0.0

50.

48±0

.05

1.5±

0.1

1.3±0.05*1

1.1±0.1

0.55

±0.

03

0.11

+0.

1

–0.0

50.

16±

0.05

0.9±0.10.2±0.1a b c


Remark Dimension*1

is bigger than dimension*2

(dimension*2

= a + b + c).

*2




(Unit : mm)

6-Pin Super Minimold (M01, TB)

0.9±

0.1

0.7

0 to

0.1 0.

15+

0.1

–0

.05

0.2+

0.1

–0

.05

2.0+

0.15

–0

.20

1.3 0.

650.

65

1.25±0.1

2.1±0.1

0.1 MIN.

0.60

±0.

1

0.13

±0.

05

0.45

0 to

0.1

2.10±0.1

1.25±0.1

2.00

±0.

2

1.30

0.22

+0.

1

–0.0

5

0.65

0.65

12

3

65

4

6-Pin Thin-Type Super Minimold

Flat-Lead 6-Pin Thin-Type Ultra Super Minimold

0.55

±0.

05

0.11

+0.

1

–0.0

5

0.48

0.48

0.96

0.20

+0.

1

–0.0

5

1.50

±0.

1

32

1

45

6

1.10±0.1

1.50±0.1




(Unit : mm)

6-Pin Plastic SON

2.0

3.0

0.75±0.1

(Bottom View)

0.95

0.95

0.35

+0.

07–0

.05

0.7±

0.1

0.19

0.7±0.1

0.29±0.1 0.29±0.1

0.25+0.07–0.05




0.5±

0.06

0.2±0.1 0.7±0.1


1.5±

0.1

1.5±0.1

0.37+0.03–0.05

0.2+

0.07

–0.0

5

0.3±0.07

(Side View)

1.2±

0.1

(Unit : mm)

6-Pin Plastic TSON (T5N)

6-Pin Plastic TSON (T6N)

0.5±

0.06

AA

0.2±0.1 0.7±0.1


1.5±

0.1

1.5±0.1

0.37+0.03–0.05

0.08

MIN

.

0.2+

0.07

–0.0

5

0.3±0.07

(0.24)

(Side View)

1.2±

0.1

Remark A>0

( ) : Reference value




(Unit : mm)

6-Pin Plastic TSON (T6X)

Remark A>0


AA

0.2±0.1 0.7±0.1


1.5±

0.1

1.5±0.1

0.37+0.03–0.05

0.08

MIN

.

0.2+

0.07

–0.0

5

0.3±0.07

(0.24)

(Side View)

0.5±

0.06

1.2±

0.1

(Bottom View)

(Top View)

2.0±0.1

1.3±

0.1

(Side View)

0.5±

0.06

(C0.15)

0.15

+0.

07–0

.05

0.08

MIN

.

1.1±0.1

0.2±0.1

AA

1.14

±0.

1

0.37+0.03–0.05

Remark A>0


6-Pin Plastic RTSON (T7C)




(Unit : mm)

6-Pin Plastic TSSON (T5K)

1.0±

0.1 0.

35±

0.06

0.35

±0.

06 0.45

±0.

1

0.13±0.07

0.15

+0.

07–0

.05

0.23±0.07

0.175±0.075

(Bottom View)

(Top View)1.

0±0.

1

1.0±0.1

1.0±0.1

0.37+0.03–0.05

0.15+0.07–0.05




1.0±

0.1 0.

35±

0.06

0.35

±0.

06 0.45

±0.

1

0.13±0.07

0.15

+0.

07–0

.05

0.08

MIN

.

0.23±0.07

0.175±0.075

(Bottom View)

(Top View)1.

0±0.

1

1.0±0.1

1.0±0.1

0.37+0.03–0.05

0.15+0.07–0.05

0.08 MIN.A

AA

A

Remark A>0

(Unit : mm)

6-Pin Plastic TSSON (T6R)




(Unit : mm)

8-Pin Lead-Less Minimold

1.49

0.85 MAX.

0.12 M

1.57±0.2

0.1±0.1

0.42+0.08–0.07

detail of lead end

3˚+7˚–3˚

1.27

8 5

1 45.2±0.2

6.5±0.3

0.6±0.2

1.1±0.24.4±0.15

0.17+0.08–0.07

0.10

8-Pin Plastic SOP (5.72 mm (225))

1 2 3 4

8 7 6 5

2.2±

0.05

2.0±

0.1

(Top View)

0.5±

0.03

4 3 2 1

5 6 7 8

0.4±

0.1

0.4±

0.1

(1.4

)

(0.75)(0.75)

(0.25) (0.25)

0.16±0.05

(Bottom View)

2.0±0.1

(0.3

5)(0

.35)

(0.3

5)(0

.35)

(0.5

)(0

.5)

(0.6

)(0

.6)

(0.65)(0.65)

(0.6)

(0.3)

0.12

5+0.

1

–0.0

5




(Unit : mm)

8-Pin Plastic SSOP (4.45 mm (175))

1.5±0.1

0.575 MAX.

0.10 M

1.8 MAX.

0.1±0.1

0.3+0.10–0.05

detail of lead end

3˚+7˚–3˚

0.65

8 5

1 42.9±0.1

4.94±0.2

0.5±0.2

0.87±0.23.2±0.1

0.15+0.10–0.05

0.15

8-Pin Plastic TSON

AA

0.7±0.1


1.5±

0.1

1.5±0.1

0.37+0.03–0.05

0.08

MIN

.

0.15

+0.

07–0

.05

0.3±0.07

(0.24)

(Side View)

0.4±

0.06

0.2±0.1

1.2±

0.1

(C0.15)

Remark A>0





(Unit : mm)

10-Pin Plastic TSON (TQ)

(Bottom View)(0.15)

(1.70) (0.30)(0

.95)

(0.0

5)

(1.9

5)(0

.30)

0.40±0.05

2.25

±0.

1

2.55

±0.

15

0.18±0.05

2.20±0.1

2.30±0.15

(0.1

25)

(0.6

0 M

AX

.)




(Unit : mm)

10-Pin Plastic TSSOP

detail of lead end

–10˚

to 2

0˚

(10 - 0.2)

(0.5)

2.75±0.15

(2.2

)

3.2±

0.2

1.05±0.15

(0.9)

0.35

±0.

15

0.15±0.1

(0.1)

0.4±

0.06

AA

0.2±0.1


2.0±

0.1

1.35±0.1

0.37+0.03–0.05 10

-0.0

8 M

IN.

10-0

.18+

0.07

–0.0

5

0.45±0.1

(Side View)

Remark A>0


1.49

±0.

1

(C 0.15)

10-Pin Plastic TSSON (T6Q)




3.0±0.1

3.0±

0.1

0.75±0.1

(Bottom View)

0.5±0.06

1.0

1.55

±0.

10.

4±0.

1

0.9 0.4

0.9

0.4

Dimensions of pin No.1 indication

0.5±

0.06

1.0

0.4±0.1

0.24+0.07–0.05

1.55±0.1 0.4±0.1

0.4±

0.1

(Unit : mm)

12-Pin Plastic QFN (T5F)



Package Dimensions (19/47) (Unit : mm)


2±0.

1

2±0.1

0.57+0.03–0.05

AA0.08 MIN.

0.2+0.07–0.05

1.2±0.1

(Side View)

0.5±

0.1

0.2±

0.07

5

1.2±

0.1

(C0.2)

(0.3

2)

12-Pin Plastic QFN (T7K)

<R>




2.5±0.05

2.5±

0.05

(Bottom View)

0.50

1.44

0.15

0.4 MAX.

0.15

0.23

±0.

05

0.23±0.05 1.44

(Unit : mm)

12-Pin Plastic TQFN




2.0±0.1

2.0±

0.1

(Bottom View)

0.23±0.1

0.94

±0.

1

0.94±0.1

0.23

+0.

07–0

.05

(C 0.17±0.07) 0.50±0.06

0.37+0.03–0.05

(Unit : mm)

12-Pin Plastic TSQFN (T5L)




2.0±0.1

2.0±

0.1

(Bottom View)

0.23±0.1

0.94

±0.

1

0.94±0.1

0.23

+0.

07–0

.05

0.11

MIN

.

AA

(C 0.17) 0.50±0.06

0.37+0.03–0.05

Remark A>0


(Unit : mm)

12-Pin Plastic TSQFN (T6M)




(Unit : mm)


2.5±0.1

2.5±

0.1

0.6 MAX.

(Bottom View)

0.5±0.05

(1.15)

(0.3) (0.3)(0.95) (0.95)

(0.3

)(0

.3)

(0.9

5)

0.3±

0.05

(0.9

5)

0.3±0.05

0.675±0.07

0.85±0.07

0.67

5±0.

07

0.85

±0.0

7

0.5±

0.07 (1

.15)

0.5±

0.05

0+0.03–0

0+0.1 –0

Through hole

Solder resist




(Unit : mm)



detail of lead end

3˚+7˚–3˚

6.55±0.2

4.38±0.1

0.6±0.2

1.1±0.16

0.15+0.10–0.05

0.10

1.49

1.42 MAX.

0.1±0.1

1.59+0.21–0.20

0.4+0.10–0.05 0.10 M

1.27

10.2±0.261 7

14 8

detail of lead end

5˚± 5˚

14 8

1 7

5.40 MAX.

0.10

6.2±0.3

4.4

0.5±0.2

0.9

0.15+0.10–0.05

0.30+0.10–0.05

1.8 MAX.

1.44

0.75 MAX.

0.125±0.075

0.10 M

0.65




(Unit : mm)

16-Pin Plastic QFN (T5T)

C0.2

0.2±0.07

(1.6)


3.0±

0.1

3.0±0.1

0.75±0.1

0.5±

0.06

(Side View)

(1.6

)

3.0±

0.1

3.0±0.1

0.4±0.1

16-Pin Plastic QFN (T6C)

16-0.23±0.05

1.7±0.05


3.0±

0.1

3.0±0.1

0.75±0.1

0.5±

0.05

(Side View)

1.7±

0.05

16-0.32±0.1




(Unit : mm)


detail of lead end

5˚± 5˚

16 9

1 8

5.2±0.3

6.4±0.2

4.4±0.2

0.5±0.2

1.0±0.2

0.17+0.08–0.07

0.10 S

1.8 MAX.

1.5±0.1

0.475 MAX.

S

0.22+0.10–0.05

0.125±0.075

0.10 M

0.65

C0.2

0.2±0.07

(1.6)


3.0±

0.1

3.0±0.1

0.75±0.1

0.5±

0.06

(Side View)

(1.6

)

3.0±

0.1

3.0±0.1

0.4±0.1

Remark A>0


AA0.08 MIN.

16-Pin Plastic QFN (T6S)




(Unit : mm)

16-Pin Plastic TSON

3.3±0.1

2.3±

0.1

2.5±

0.15

0.4±0.050.16±0.05

3.5±0.15

0.6

MA

X.

(Bottom View)

(1.1

)

(1.6

)(0

.45)

(2.2)(0.55)

16-Pin Plastic HTSSOP

(1.5)

0.9±0.2

0.20±0.10

(0.4

)(2

.7)

(0.5

)

(1.8)

(0.1)

(2.5)5.2±0.2

5.5±

0.3

6.4±0.3

0.65

±0.

10.

20±

0.10

16

9

1

8




(Unit : mm)

20-Pin Plastic QFN (0.4 mm pitch)

3.2±

0.2

3.0±

0.2

3.2±

0.2

4.2±0.2

4.0±0.2

3.0±

0.2

Pin 1

Pin 20

0.18±0.05

0.4

0.30±0.15

(Bottom View)

Caution The island pins located on the corners are needed to fabricate products in our plant, but do not serve any other function. Consequently the island pins should not be soldered and should remain non-connection pins.

4.2±0.2

4.0±0.2

0.9

MA

X.

0.14

+0.

10–0

.05

20-Pin Plastic RQFN (T5R)

2.45±0.1

1.45

±0.

10.

3±0.

1

0.23+0.07–0.05 0.50±0.06

3.5+0.075–0.1

2.5+

0.07

5–0

.1

(Bottom View)(Top View) (Side View)

0.55±0.05




(Unit : mm)

20-Pin Plastic QFN (0.5 mm pitch) (K)

(Bottom View)

4.15±0.15

3.80±0.1

4.15

±0.

15

3.80

±0.

1

Pin 1

0.6 MAX.

0.6

MA

X.

0.50

1.9

1.9

0.20

Pin 1

0.45

0.9±0.1

Pin 1 Identifier

Pin 1 Identifier

(Top View) (Side View)

0.45

+0.

2–0

.1

0.23+0.07–0.05

0.01+0.04–0.01




(Unit : mm)

20-Pin Plastic QFN (0.5 mm pitch) (T7G)

(Bottom View)

2.7±

0.1

0.5±0.1

2.7±0.1

4±0.1

4±0.

1

0.35±0.075

Pin 1

1.720.15

0.08

MIN

.

AA

1.72 0.

15


Remark A>0

0.57+0.03–0.05

0.2+

0.07

–0.0

5




(Unit : mm)

20-Pin Plastic TQFN (T6E)

3.5±0.1

3.5±

0.1

(Bottom View)

0.57+0.03–0.05

0.5±0.06

0.18

0.18

2.2±

0.1

2.2±0.1

1.48

5

1.485

20-0

.25+

0.07

–0.0

5

20-0

.35±

0.1




(Unit : mm)


3±0.1

3±0.

1

0.6 MAX.

0+0.1 –0

(Bottom View)

(2.4)

0.3±0.05(0.5)

(0.5

)0.

3±0.

05

0.3±

0.05

0.3±

0.05

(2.4

)

1.0

1.0

1.1

1.1

0.3±0.05 0.3±0.05

Pin 1

Pin 20

Remark ( ) : Reference value : Hollow hole

: Solder resist

0+0.

03–0

Detail




(Unit : mm)


detail of lead end

3˚+7˚–3˚

7.7±0.3

5.6±0.2

0.6±0.2

1.1

0.20+0.10–0.05

1.55±0.1

0.78 MAX.

0.1±0.1

1.8 MAX.

0.4±0.1 0.12 M

1.270.10

12.7±0.3

1 10

20 11


detail of lead end

3˚+7˚–3˚

0.5±0.2

0.15+0.10–0.05

6.4±0.2

4.4±0.11.0±0.2

1.8 MAX.

1.5±0.1

0.1±0.1

0.22+0.10–0.05

0.575 MAX.0.10 M

0.65 0.15

20 11

1 10

6.7±0.3




(Unit : mm)

24-Pin Plastic QFN


4.2±

0.2

4.0±

0.2

5.2±0.2

Pin 24

5.0±0.2

0.22±0.05 0.45±0.15

0.5

(Bottom View)

1.0

MA

X.

Pin 1

0.14

+0.

10–0

.05

5.2±0.2

5.0±0.2

4.0±

0.2

4.2±

0.2




(Unit : mm)

24-Pin Plastic QFN (T7L)

4.0±0.1

4.0±

0.1

(Bottom View)

0.57+0.03

−0.05

0.2+0

.07

−0.0

5

0.5±0.10.35±0.075

(C0.2)


(Dimensions of Each Pin Part)A

A0.

08 M

IN.

Pin1

Remark A > 0

2.7±0.1

2.7±

0.1

<R>




(Unit : mm)

28-Pin Plastic QFN (K)

5.1±

0.2

Pin 28

Pin 1

5.1±

0.2

4.7±

0.2

5.5±0.2

5.1±0.2

4.7±

0.2

1.0

MA

X.5.5±0.2

5.1±0.2

0.14

+0.

10–0

.05

0.55±0.200.24±0.05

(Bottom View)

0.5

0.6

0.5

0.5

0.6

Caution The extra-wide pins (shaded portion) located between pins 11 and 12 and pins 25 and 26 in this package are needed to fabricate products in our plant, but do not serve any other function. Consequently the pins should not be soldered and should remain non-connection pins.




(Unit : mm)

28-Pin Plastic QFN (T7A)

5.0±0.1

5.0±

0.1

(Bottom View)

0.72±0.05

3.02±0.1

0.4±

0.05

0.5

3.02

±0.

1

0.5

0.2±0.050.08 MIN.

(C0.2)


(Dimensions of Each Pin Part)

0.2±

0.05

AA

0.08

MIN

.

0.4±0.05

(0.325)

Pin1

Remark A>0





(Unit : mm)


30 16

9.85±0.26

1 15

6.1±0.2

8.1±0.2

0.5±0.2

1.0±0.2

0.15+0.10–0.05

0.51 MAX.

2.0 MAX.

1.7±0.1

0.125±0.075

0.3±0.1

0.65

0.10 M

0.10

detail of lead end

3˚+7˚–3˚

32-Pin Plastic QFN (T5S)

Laser Marked Index

5.0±0.1

5.0±

0.1

(Bottom View)(Side View)(Top View)

(Side View)

(0.21)

0.85

MA

X.

(0.7

5)

(0.20)

0.16

±0.

050.

76±

0.1 (0.865) (1.1)0.4

(1.75)

(1.7

5)

1221




(Unit : mm)

44-Pin Plastic QFN

6.2±

0.2

6.0±

0.2

6.2±0.2

6.0±0.2

44 Pin

1 Pin

6.2±

0.2

6.0±

0.2

6.2±0.26.0±0.2

1.0M

AX

.

0.14

+0.

10–0

.05

0.18±0.05 0.55±0.2(Bottom View)

0.4


36-Pin Plastic QFN

6.2±

0.2

6.0±

0.2

0.22±0.05 0.55±0.2

0.5

(Bottom View)

6.2±0.26.0±0.2

1.0M

AX

.

0.14

+0.

10–0

.05

6.2±

0.2

6.0±

0.2

6.2±0.2

6.0±0.2

36 Pin

1 Pin





(Unit : mm)

79A

0.9±

0.2

0.2±

0.1

0.4±0.15

5.7 MAX.

5.7

MA

X.

0.6±

0.15

0.8±

0.15

4.4

MA

X.

4.2 MAX.

Source

Gate Drain

(Bottom View)

3.6±0.2

1.5±0.21.

2 M

AX

.

0.8 MAX.

1.0

MA

X.

Source

Gate Drain

75

2.3

1.13

0.9

MA

X.

GATE

DRAIN

0.5

SOURCE

2.7

3.0

MIN

.

2.3

9.8 MAX.

2.7

7.0

1.8φ

77

17.5±0.514.3

SOURCEGATE

1.0±0.1

6.35

±0.

4

4.0 MIN. BOTHLEADSDRAIN

R1.25, 2 PLACES

2.5

8.9±0.4

3.8

MA

X.

1.0

0.2 MAX.

2.26

±0.

4 0.1+

0.06

–0.0

2




(Unit : mm)

95

7.2±0.2

4.5

MA

X.

0.1

0.2

MA

X.2.

1±0.

15

1.0

14.0±0.3

5.9±

0.2

4.0

MIN

.

0.7±0.1

GATE

2.5±0.3 DIA

SOURCE

18.5 MAX.

DRAIN

96/99

6.0±0.2

0.1

1.20.2

MA

X.

1.7±

0.15

5.0

MA

X.

4.0 MIN. BOTH LEADSSOURCE

GATE

DRAIN

0.6±0.1

5.2±0.3

11.0±0.3

15.0±0.3

1.0±0.1

4.3±

0.2

4.0

2.2±0.32 PLACESφ

84, 84A, 84C

(−SL) 1.7MIN.

(−T1) 1.0±0.2L

1.7

MA

X.

0.1

L

1.78±0.2

1.78

±0.

2

0.5 TYP.

L

42

3

1

0.5

TY

P.

83A, 83B

1.88±0.3

0.5±

0.1

1.88

±0.

3

4.0

MIN

.

4.0

MIN

.

4

2

3

4.0 MIN.4.0 MIN.

1

1.0±0.1

1.45

MA

X.

0.1+

0.07

–0.0

3




(Unit : mm)

S01

0.5

TY

P.

2.0±

0.2

4

0.65 TYP.

3

2

1

2.0±0.2

2.0±0.2

1.9±0.21.6

4.0±0.2

0.12

5±0.

05

1.5

MA

X.




(Unit : mm)

S02, S03

(Top View)

(Side View)

(Bottom View)

0.5

TY

P.

2.6±

0.1

0.65 TYP.

3.2±0.2

1

2

3

4

2.2±0.2

3.2±0.2

1.7

1.5

MA

X.

0.15

±0.

05

3

4

1

2

2.2±0.2

2.2±

0.2




(Unit : mm)

T-92MT-91M (3M)

T-86M

5.7±

0.2

11.4

±0.

2

4.6±0.2

14.5±0.3

24.5±0.25

4-C1.0

4-R1.2

3.2±0.3 0.9±0.3

2.4±

0.3

S S

2.4±

0.2

4.9

MA

X.

20.9±0.3

3.7

MIN

.3.

7 M

IN.

D2D1

G2G1

45˚

0.6±

0.3

2.1±

0.3

4.0±0.3 1.4±0.3

30.4±0.25

S

8.0±

0.2

0.6±

0.3

17.4

±0.

15

9.7±0.2

35.2±0.25

23.9±0.3

2.6±

0.3

S

4–R1.3

4–C1.5

D1 D2

G1 G2

45˚

2.4±

0.2

5.7

MA

X.

2.1±

0.3

2.7

MIN

.2.

7 M

IN.

3.3±0.15φ

5.84

±0.

25

13.8

±0.

35

3.5±0.2

14.27±0.15

(2.865)

20.22±0.15

8.54±0.2 4.2±

0.4

0.15

±0.

05

2.04

±0.

15

1.8±

0.3

1

2

3




(Unit : mm)

9.85

19.8

27.9

34.0

20.7

12.7

Drain

Source

Gate4–C1.5

3.25

4.4

1.3

1.69

0.15

T-97M (3P)

T-101M (3S)

8.48±0.2

35.56±0.15

41.15±0.15

31.2±0.2

S

2–R1.6±0.3

4–C1.5±0.3

G1 G2

D1 D2

2.13

±0.

15

5.0±

0.4

1.8±

0.3

16.5

1±0.

35

0.15

±0.

0510

.16±

0.25

S : SourceD1, D2 : DrainG1, G2 : Gate

PIN CONNECTION

2.4±

0.2 5.7

MA

X.

2.1±

0.3

20.4±0.25

24.0±0.25

16.0±0.3

1.4±0.3

4.0±0.3

2.6±

0.3 2.

7 M

IN.

2.7

MIN

.

4–R1.3

4–C1.5

S S

D

G

8.0±

0.2

17.4

±0.

15

0.6±

0.3

T-142M




(Unit : mm)

TO-92

5.2 MAX.

1.27

1 2 3

5.5

MA

X.

4.2

MA

X.

1.77

MA

X.

12.7

MIN

.0.5

2.54




(Unit : mm)

7-Pin Special With Heatsink

27.5 MAX.

38.1±0.25

45.08 MAX.

4.0±

0.25

8.1

MA

X.

3.2

MA

X.

14.8

5 M

AX

.

0.51±0.05

12.9

MA

X.

21.5

MA

X.

4.19

±0.

13

6-32UNC2B

1 2 3 7 8 95

19.05±0.38

2.54±0.38

0.51±0.05

2.62

±0.

35 10.7

5±0.

25

4.25+0.25–0.35

±0.050.38.. A

2.56.3

2.54±0.25

25.4±0.25

A

φ



Mounting Pad Layout (1/6)


1.9

0.8

1.0

2.4

0.95

12

3

3-Pin Minimold (33 PKG)

0.6

1.0

0.6

1.3

0.5

12

3

3-Pin Ultra Super Minimold(19, 1608 PKG)

3-Pin Power Minimold (34 PKG)

1.3

0.6

1.7

0.65

12

3

0.8

3-Pin Super Minimold3-Pin Super Lead-Less

Minimold (M33, 0804 PKG)

(Unit : mm)

Remark : Mold package : Lead

0.15

0.940.05 0.35

0.22

5

0.24

0.05

0.57

0.28

5


0.100.10

0.20 0.

05

0.05

0.35

0.35

0.15 0.50

0.90

0.200.050.05

0.20

0.05

0.05

12

3

0.95

0.4

0.5

0.4

0.9

0.45

Flat-Lead 3-Pin Thin-Type Ultra Super Minimold

0.4

4-Pin Lead-Less Minimold(M14, 1208 PKG)

0.8

0.8

0.45

0.25

2.2

1.0

2.0 2.0

1.0 1.0

1.4

0.4

0.9

2.8

45°

45°

3-Pin Thin-Type Lead-LessMinimold (M53, T6J)

0.45

0.55

1.25

0.5

21

3

0.55

0.45

0.45




0.95 0.95

2.4

0.6

1.0

6-Pin Minimold

(Unit : mm)

0.6

1.25

1.7

43

12

0.8

4-Pin Super Minimold (18)

6-Pin Super Lead-Less Minimold (1007 PKG)

0.151.2

0.05

0.35

0.22

5

0.50.05

0.12

50.

35


6-Pin Lead-Less Minimold(M16, 1208 PKG)

0.40.4

0.8

0.45

0.25

1.5

0.8

2.2

1.0

1.5 1.5

1.0 1.0

2.7

4-Pin Power Minimold

Flat-Lead 4-Pin Thin-TypeSuper Minimold (M05, 2012 PKG)

1.3

1.55

0.5

0.6

12

3 4

6-Pin Lead-Less Minimold (1511 PKG)for Silicon MMIC/GaAs MMIC

0.480.48

1.10

0.45

0.26

Flat-Lead 4-Pin Thin-TypeSuper Minimold (M04)

12

43

1.25 1.3

1.6

0.6

0.5

0.6

1.0

1.9

2.4

1

4

2

31.

0

4-Pin Minimold (39)




(Unit : mm)

0.35 0.65

4.45

1.27

8-Pin Plastic SSOP(4.45 mm (175))

0.480.48

0.30

1.20

0.40

Flat-Lead 6-Pin Thin-Type UltraSuper Minimold

10-Pin Plastic TSON

0.5750.575

0.8750.8750.6 0.6

0.2

0.4

0.40.

80.

80.

950.

95

0.3 0.5 0.3

0.2

0.3

0.5

0.3

1.0

0.5

6-Pin Plastic TSON


0.5

0.5

0.5

0.8

1.8

0.26

0.65

1.6 0.

05

0.1645˚

Pin1

0.524

6-Pin Plastic TSSON (T5K)

0.31 0.310.29 0.29

6–0.

22

0.35

0.35

0.65 0.65

1.9

0.8

0.4

6-Pin Super Minimold (M01, TB)

1.2

0.12

50.

225

1.2

0.15

0.15 0.15 0.15

0.45

0.65

0.35 0.35

6-Pin Plastic TSSON (T6R)

0.7

1.2

8-0.15

1.1

1.7

0.4

8-Pin Plastic TSON

Note

Note: This layout can also be adopted to some of the products in T6R package. Please refer to the data sheet of each product.

<R>

<R>




(Unit : mm)

1.1 1.1

0.5

0.2

0.5

1.6

1.6

16-Pin Plastic QFN (T5T/T6S)

0.35 0.65

5.72

1.27


0.8

0.8

0.6

0.5

1.15

0.3

0.51.15

0.3

0.80.8 0.6

14-pin LGA (CSP Type)

12-Pin Plastic TSQFN (T5L)

0.94

0.50.77

0.50.770.33

0.5 0.77

0.5

0.77

0.33

0.330.9412

–0.2

3

0.33

12-Pin Plastic TQFN

0.5

0.720.97

12–0.25

0.720.97

1.41.4

0.720.

970.

720.

971.

41.

4

0.5

12-Pin Plastic TSQFN (T6M)

0.94

0.5

1.15

0.5

1.15

0.5 1.

15

0.5

1.15

0.9412–0

.23

0.770.77

0.77

0.77

1.55

0.5

1.0

12–0.3

12-Pin Plastic QFN

0.5

1.0 0.650.65

0.51.

0

0.5

1.0

0.65

0.65

1.55

0.4

0.8

0.4

0.8

10-0

.18

1.49

0.475

0.825

0.475

0.825

0.45

10-Pin Plastic TSSON

0.50.8

1.15 1.150.8

0.5C0.2

0.5

0.8

1.15

1.15

1.2

12−0

.15

1.2

0.8

0.5

12-Pin Plastic QFN (T7K)

<R>




(Unit : mm)

0.30.5

0.3

1.2

0.5 0.

50.

50.5 0.4 3.

900.

70

4.300.70

R0.15

R0.2

R0.15

28-Pin Plastic QFN (K)24-Pin Plastic QFN

0.30.5

0.3

0.5 3.

10.

7 to

0.8

4.1

2– 0.3φ

2– 0.3φ

0.7 to 0.8

20-Pin Plastic RQFN

0.4 1.45 1.45

0.5

1.45

2.45

0.5

20−0

.23

0.4

0.4

0.95

0.95

0.4

C0.2

8−C0.06

20-Pin Plastic QFN (0.4 mm pitch)

0.4

0.2

0.4 2.

40.

6

3.40.6 0.6

0.6

0.2

0.35

5.72

0.65

1.27


0.35

5.72

0.65

1.27


20-Pin Plastic QFN (0.5 mm pitch) (T7G)

2.15

2.15

1.65

1.65

1.35

1.35

0.5

20-0.2

2.15 2.151.65 1.65

1.351.35

16-Pin Plastic QFN (T6C)

3.3

0.33

0.23

1.7

1.7

3.3

0.47

0.23

24-Pin Plastic QFN (T7L)

2.15

2.15

1.6

51

.65

1.35

1.35

0.5

pitc

h0.

25

0.25 24-0.2

2.15 2.151.65 1.65

1.351.35

<R>




(Unit : mm)

S01

2.4

2.4

79A

1.74.0

1.0 1.

0

5.9

1.2

Gate Drain

0.5 0.5

6.1

Through Hole: 0.2 × 33φ

Stop up the hole with a rosin or something to avoid solder flow.

Source

28-Pin Plastic QFN (T7A)

3.02

0.5

3.02

28–0.2

0.5

2.65 2.652.1 2.1

2.65

2.65

2.1

2.1

C - 1

REVISION HISTORY PACKAGES LINE-UP FOR RF AND MICROWAVE DEVICES Common Information

Description Rev. Date

Page Summary 1.00 Jul 22, 2010 ⎯ Previous Number:PX10051EJ35V0TN p.5 <Surface Mount Type Package Line-up Actual Size Illustrations>

Addition of 20-Pin Plastic TQFN (T6E) p.6 <List of Surface Mount Type Package Drawings (1/2)>

Addition of 6-Pin Plastic RTSON (T7C) Addition of 8-Pin Plastic TSON

pp.9, 10,12, 13, 16

<Package List> Addition of package code for 3-Pin Thin-Type Lead-Less Minimold (M53, T6J)Addition of 6-Pin Plastic RTSON (T7C) Addition of 8-Pin Plastic TSON Addition of 20-Pin Plastic TQFN

pp.21, 30, 34

<Package Dimensions> Addition of package code for 3-Pin Thin-Type Lead-Less Minimold (M53, T6J)Addition of 6-Pin Plastic RTSON (T7C) Addition of 8-Pin Plastic TSON

pp.62, 64

<Mounting Pad Layout> Addition of package code for 3-Pin Thin-Type Lead-Less Minimold (M53, T6J)Addition of 8-Pin Plastic TSON

2.00 Oct 13, 2010 p.5 <Surface Mount Type Package Line-up Actual Size Illustrations> Addition of 6-Pin Plastic RTSON (T7C) Addition of 8-Pin Plastic TSON

p.7 <List of Surface Mount Type Package Drawings (2/2)> Addition of 28-Pin Plastic QFN (T7A)

pp.12, 13, 17

<Package List> Addition of the illustration of 6-Pin Plastic RTSON (T7C) Addition of the illustration of 8-Pin Plastic TSON Addition of 28-Pin Plastic QFN (T7A)

p.53 <Package Dimensions> Addition of 28-Pin Plastic QFN (T7A)

p.68 <Mounting Pad Layout> Addition of 28-Pin Plastic QFN (T7A)

3.00 Apr 27, 2011 p.6 <Surface Mount Type Package Line-up Actual Size Illustrations> Addition of 20-Pin Plastic QFN (0.5) (T7G) Addition of 28-Pin Plastic QFN (T7A)

p.8 <List of Surface Mount Type Package Drawings (2/2)> Addition of 20-Pin Plastic QFN (0.5) (T7G)

pp.17, 18

<Package List> Addition of the illustration of 20-Pin Plastic QFN (0.5) (T7G) Addition of the illustration of 28-Pin Plastic QFN (T7A) Addition of 20-Pin Plastic QFN (0.5) (T7G)

p.50 <Package Dimensions> Addition of 20-Pin Plastic QFN (0.5) (T7G)

p.70 <Mounting Pad Layout> Addition of 20-Pin Plastic QFN (0.5) (T7G)

C - 2

Description Rev. Date Page Summary

4.00 Dec 11, 2012 p.6 <Surface Mount Type Package Line-up Actual Size Illustrations> Addition of 12-Pin Plastic QFN (T7K) Addition of 24-Pin Plastic QFN (T7L)

p8 <List of Surface Mount Type Package Drawings> Addition of 12-Pin Plastic QFN (T7K) Addition of 24-Pin Plastic QFN (T7L)

p15 <Surface mount type 12, 14-pin package list> Addition of 12-Pin Plastic QFN (T7K)

p18 < Surface mount type 24, 28, 30, 32, 36-pin package list> Addition of 24-Pin Plastic QFN (T7L)

pp.40, 56

<Package List> Addition of 12-Pin Plastic QFN (T7K) Addition of 24-Pin Plastic QFN (T7L)

P71 < Mounting Pad Layout > The note is added in Mounting Pad Layout of 6-Pin Plastic TSSON (T5K).

pp.72, 73

< Mounting Pad Layout > Addition of 12-Pin Plastic QFN (T7K) Addition of 24-Pin Plastic QFN (T7L)

PACKAGES LINE-UP FOR RF AND MICROWAVE DEVICES Common Information Publication Date: Rev.1.00 Jul 22, 2010 Rev.4.00 Dec 11, 2012 Published by: Renesas Electronics Corporation

http://www.renesas.comRefer to "http://www.renesas.com/" for the latest and detailed information.

California Eastern Laboratories, Inc.4590 Patrick Henry Drive, Santa Clara, California 95054, U.S.A.Tel: +1-408-919-2500, Fax: +1-408-988-0279

Renesas Electronics Europe LimitedDukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.KTel: +44-1628-651-700, Fax: +44-1628-651-804Renesas Electronics Europe GmbHArcadiastrasse 10, 40472 Düsseldorf, Germany Tel: +49-211-65030, Fax: +49-211-6503-1327 Renesas Electronics (China) Co., Ltd.7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China Tel: +86-10-8235-1155, Fax: +86-10-8235-7679Renesas Electronics (Shanghai) Co., Ltd.Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898 Renesas Electronics Hong Kong LimitedUnit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong KongTel: +852-2886-9318, Fax: +852 2886-9022/9044Renesas Electronics Taiwan Co., Ltd.13F, No. 363, Fu Shing North Road, Taipei, TaiwanTel: +886-2-8175-9600, Fax: +886 2-8175-9670Renesas Electronics Singapore Pte. Ltd. 80 Bendemeer Road, Unit #06-02 Hyflux Innovation Centre Singapore 339949Tel: +65-6213-0200, Fax: +65-6213-0300Renesas Electronics Malaysia Sdn.Bhd. Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, MalaysiaTel: +60-3-7955-9390, Fax: +60-3-7955-9510Renesas Electronics Korea Co., Ltd.11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, KoreaTel: +82-2-558-3737, Fax: +82-2-558-5141

SALES OFFICES

© 2012 Renesas Electronics Corporation. All rights reserved.[Colophon 1.3]


R50ZZ0001EJ0400

PACKAGE LINE-UP FOR RF AND MICROWAVE …...R50ZZ0001EJ0400 Rev.4.00 Page 1 of 74 Dec 11, 2012...

Documents

Transcript of PACKAGE LINE-UP FOR RF AND MICROWAVE …...R50ZZ0001EJ0400 Rev.4.00 Page 1 of 74 Dec 11, 2012...