Pacific PR32-D5 Plus - Thermaltake · 2020. 11. 6. · Title: CL-W280-PL00SW-A_Pacific PR32-D5...
2
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. 1. Please carefully read the manual before beginning the installation process ! 2. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant. 3. DO NOT USE any kind of alcohol or alcohol derivatives with this reservoir or the acrylic tube may crack and fail ! Do not clean it using alcohol either ! Installation Guide Parts List Pump & Reservoir Bracket G1/4 Stop Plug Wrench Clip Nuts Long Screws Short Screws A x 1 B x 1 C x 1 G x 1 H x 1 L x 1 M x 1 N x 1 I x 1 J x 1 K x 4 F F There are two types of mounting kits, please choose the mounting kit you want to use. Install your fittings and tubes, remember to use the bottom as an outlet and top as an inlet. Connect the reservoir cable to the conversion cable. 1 2 3 A B B D E E Support 16.8 Million Colors Pump+Reservoir L Controller Power Cable Velcro Controller Cable Conversion cable Bridge Cable Pacific PR32-D5 Plus E x 4 F x 4 D x 4 or D
Transcript of Pacific PR32-D5 Plus - Thermaltake · 2020. 11. 6. · Title: CL-W280-PL00SW-A_Pacific PR32-D5...
This product is intended for installation only by expert users. Please consult with a qualified technician for installation.
Improper installation may result in damage to your equipment.
1. Please carefully read the manual before beginning the installation process !
2. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant.
3. DO NOT USE any kind of alcohol or alcohol derivatives with this reservoir or the acrylic tube may crack and fail ! Do not clean it using alcohol either !
Installation Guide
Parts List
Pump & ReservoirBracket G1/4 Stop Plug WrenchClip Nuts Long Screws Short Screws
A x 1B x 1 C x 1 G x 1 H x 1
L x 1 M x 1 N x 1I x 1 J x 1 K x 4
F
F
There are two types of mounting kits, please choose
the mounting kit you want to use.
Install your fittings and
tubes, remember to use
the bottom as an outlet
and top as an inlet.Connect the reservoir
cable to the conversion
cable.
1 2 3
A
B
B
D
E
E
Support
16.8 Million ColorsPump+Reservoir
L
Controller Power Cable VelcroController Cable Conversion cable Bridge Cable
Pacific PR32-D5 Plus
E x 4 F x 4D x 4
or
D
Installation Guide
4
6
5
J
Connect the reservoir cable onto the controller.
Set the DIP switch on the back side of the controller
to assign the number of the controller
7
123 45
J
NO.1
ON
1 2 3 4
NO.3
ON
1 2 3 4
NO.2
ON
1 2 3 4
NO.4
ON
1 2 3 4
NO.9
ON
1 2 3 4
NO.11
ON
1 2 3 4
NO.10
ON
1 2 3 4
NO.12
ON
1 2 3 4
NO.5
ON
1 2 3 4
NO.7
ON
1 2 3 4
NO.6
ON
1 2 3 4
NO.8
ON
1 2 3 4
NO.13
ON
1 2 3 4
NO.15
ON
1 2 3 4
NO.14
ON
1 2 3 4
NO.16
ON
1 2 3 4
Connect the controller cable onto the mainboard
(USB 2.0 9 pin) and controller.
9
10
8
If you want to connect two or more connectors,
you can use the bridge cable to connect the
controllers.
Connect the power cable to the 4pin Molex
connecter and controller.
K K
K
M M
© 2020 Thermaltake Technology Co., Ltd. All Rights Reserved.
www.thermaltake.com
After adding the recommended coolant, remember to
fill the reservoir to only 80% and leave the fill port cap
off. This will help stabilize your internal loop pressure
Keep the reservoir cap dry! Do not allow coolant to access the wire and the LED module
Caution!
ON 1
23
4I
Connect the Pump power cable to the 4pin Molex connecter.
