PAC_E100_110_Technical_SpecV2_00(060320)

PAC-E Series Numerical Protection Relays

TECHNICAL SPECIFICATIONS (V2.00)

PAC-E100/E110

(Over Current & Earth Fault Relay)

P&C Technologies Co., Ltd.

VER 1.0

PAC-E100 (Over Current & Earth Fault Relay)

REVISIONS REV Date Description/Reason 1.00 2005-08-11 1.Initial specification

2.00 2006-03-20 1.E110 functions are added. 2.Frequency Tracking function is deleted. 3.THD measurement function are deleted.

2/24


1. General Data 1.1 Power Supply Input Voltage 110~220 VAC±20 %, 50/60 Hz 80~300 VDC 19~28 VDC Power Consumption less then 30 VA

1.2 Current Input Nominal Frequency 50/60 Hz Phase CT Secondary 5 A or 1A Ground CT Secondary 5 A or 1A Input Range 0.1~250 A(5 A rated), 0.01~50 A(1 A rated) Burden less then 0.5 VA per phase Current Withstand 1 sec at 100 times rated , 2 sec at 20 times rated , continuous at 3 times rated

1.3 Contact Input Number 4, configurable Voltage Range 250 VDC maximum On/Off Voltage Level

Control Voltage 24/48 VDC 110~220 VDCOn Level ≥ 19 V ≥ 80 V Off Level ≤ 14 V ≤ 60 V

Recognition Time less then 10 msec

1.4 Contact Output Number 2 NO, 2 NC, configurable Make and Carry 16 A continuous, 250 VAC 30 A, 0.5 sec, 125 VDC, resistive load Breaking Capacity 0.5 A, L/R of 25 msec, 125 VDC

1.5 Communication Interface Front Panel RS-232C, 19200 bps (fixed), Modbus protocol Rear Panel RS-232C, physically identical port to front panel RS-232C Galvanic isolated RS-485, 300~38400 bps Protocol : Modbus, DNP3.0, IEC60870-5-103

1.6 Type Test Insulation IEC 60255-5, ANSI/IEEE C37.90.0 Oscillatory Transient IEC 60255-22-1, ANSI/IEEE C37.90.1 Surge Immunity IEC 60255-22-5 class Ⅳ Fast Transient IEC 60255-22-4 class Ⅳ, ANSI/IEEE C37.90.1 Electrostatic Discharge IEC 60255-22-2 class Ⅲ RFI Susceptibility IEC 60255-22-3 class Ⅲ, ANSI/IEEE C37.90.2 Vibration IEC 60255-21-1 class Ⅱ Shock IEC 60255-21-2 class Ⅱ

3/24


Seismic IEC 60255-21-3 class I, IEC60068-3-3 Humidity(non-condensing) 56days, 95 %, +40 °C, IEC60068-2-78

1.7 Environmental Carrying and Storage -25 °C~+70 °C Operating Temperatures -25 °C~+70 °C Altitude up to 2000 m

2. Protection 2.1 Definite Time Overcurrent(50_1,50_2,50N_1,50N_2) Setting Pickup Current 0.50~100.00 A, 0.05 step*)

Operating Delay 0.00~60.00 sec, 0.01 step Accuracy Pickup Current 2 % of setting value or 70 mA Operating Time 3 % or ±35 msec of setting value, @ 2xpickup current Dropout Level 96~98 % of pickup current Dropout Time less than 40 msec InformationPickup 50_1_PKP_A, 50_1_PKP_B, 50_1_PKP_C, 50_1_PKP_OR 50_2_PKP_A, 50_2_PKP_B, 50_2_PKP_C, 50_2_PKP_OR 50N_1_PKP, 50N_2_PKP Operation 50_1_OP_A, 50_1_OP_B, 50_1_OP_C, 50_1_OP_OR 50_2_OP_A, 50_2_OP_B, 50_2_OP_C, 50_2_OP_OR 50N_1_OP, 50N_2_OP

*) for 1A rated, all value divided by 5

2.2 Inverse Time Overcurrent(51,51N) Setting Pickup Current 0.50~100.00 A, 0.05 step*)

Time Multiplier 0.01~10.00, 0.01 step Trip Characteristic Curve IEC 60255-3, ANSI/IEEE, KEPCO

( )sec

1

TMC

GG

KT L

S

×

⎟⎟⎟⎟⎟

⎠

⎞

⎜⎜⎜⎜⎜

⎝

⎛

+

−⎟⎟⎠

⎞⎜⎜⎝

⎛=

T : Trip time in second K,C,L,M : Constants G : Current input GS : Pickup current setting TM : Time multiplier

Curve K L C

4/24


IEC Normal Inverse 0.14 0.02 0.00 IEC Very Inverse 13.50 1.00 0.00 IEC Extremely Inverse 80.00 2.00 0.00 IEC Long Inverse 120.00 1.00 0.00 ANSI Inverse 8.9341 2.0938 0.17966 ANSI Short Inverse 0.2663 1.2969 0.03393 ANSI Long Inverse 5.6143 1 2.18592 ANSI Moderately Inverse 0.0103 0.02 0.0228 ANSI Very Inverse 3.922 2 0.0982 ANSI Extremely Inverse 5.64 2 0.02434 ANSI Definite Inverse 0.4797 1.5625 0.21359 KEPCO Normal Inverse 0.11 0.02 0.42 KEPCO Very Inverse 39.85 1.95 1.08

Trip time for G/Gs ≥ 20 are identical to those for G/Gs = 20. Accuracy Pickup Current 2 % of setting value or 70 mA Operating Time 3 % or ±35 msec of setting value Dropout Level 96~98 % of pickup current Dropout Time less than 40 msec for instantaneously reset setting Information Pickup 51_PKP_A, 51_PKP_B, 51_PKP_C, 51_PKP_OR, 51N_PKP Operation 51_OP_A, 51_OP_B, 51_OP_C, 51_OP_OR, 51N_OP


2.3 Negative Phase Sequence Overcurrent (46) Setting Pickup Current 0.50~100.00 A, 0.05 step*)

Operating Delay 0.00~180.00 sec, 0.01 step Accuracy Pickup Current Accuracy 2 % of setting value or 70 mA Operating Time Accuracy 3 % or ±35 msec of setting value, @ 2xpickup current Dropout Level 96~98 % of pickup current Dropout Time less than 40 msec Information Pickup 46_PKP Operation 46_OP


2.4 Undercurrent (37) Setting Pickup Current 0.10~5.00 A, 0.05 step*)

Operating Delay 0.00~180.00 sec, 0.01step Accuracy Pickup Current Accuracy 2 % of setting value or 70 mA Operating Time Accuracy 3 % or ±35 msec of setting value, @ 0xpickup current Dropout Level 102~104 % of pickup current

5/24


Dropout Time less than 40 msec Information Pickup 37_PKP_A, 37_PKP_B, 37_PKP_C, 37_PKP_OR Operation 37_OP_A, 37_OP_B, 37_OP_C, 37_OP_OR


2.5 Thermal Overload (49) Setting K-Factor for IEC 60255-8 0.10~4.00, 0.01 step Time Constant(τ ) 1.0~999.9 min, 0.1 step Thermal Alarm 50~100 %, 1 step Trip Characteristic Curve(for I/k• IN <= 8) - With pre-load -Without pre-load

[min]

1

ln 2

22

⎟⎟⎟⎟⎟

⎠

⎞

⎜⎜⎜⎜⎜

⎝

⎛

−⎟⎟⎠

⎞⎜⎜⎝

⎛⋅

⎟⎟⎠

⎞⎜⎜⎝

⎛⋅

−⎟⎟⎠

⎞⎜⎜⎝

⎛⋅

⋅=

N

N

P

N

IkI

IkI

IkI

t τ

[min]

1

ln 2

2

⎟⎟⎟⎟⎟

⎠

⎞

⎜⎜⎜⎜⎜

⎝

⎛

−⎟⎟⎠

⎞⎜⎜⎝

⎛⋅

⎟⎟⎠

⎞⎜⎜⎝

⎛⋅

⋅=

N

N

IkI

IkI

t τ

t : Trip time τ : Temperature rise time constant I : Load current IP : Pre-load current k : Setting factor IN : Nominal current

Thermal State Calculation

[ ] )/exp()/exp(12

1 ττ ttIkI

mN

m −⋅Θ+−−⋅⎟⎟⎠

⎞⎜⎜⎝

⎛⋅

=Θ +

θ being calculated every 100ms I means True RMS

Accuracy Pickup Current Accuracy 2 % of setting value or 70 mA Operating Time Accuracy 10 % or ±2 sec of setting value Dropout Level 98~100 % of thermal trip setting Information Alarm 49_ARM Trip 49_TRIP

2.6 Auto-Reclosing(79) Setting Shot Number 1~4, 1 step Prepare Condition EasyLogic Operand Cycle Start Condition EasyLogic Operand

6/24


Prepare Time 0.05~200.00 sec, 0.01 step Discriminating Time 0.01~5.00 sec, 0.01 step Reclaim Time 0.01~350.00 sec, 0.01 step 1st ~ 4th Shot Delay 0.01~300.00sec, 0.01 step Command CB Close Command 79_CLS_CMD CB Final Trip Command 79_OPN_CMD Information Auto-Reclosing Ready 79_READY Auto-Reclosing In Progressing 79_IN_PROG Auto-Reclosing Fail(Final Trip) 79_FAIL Reclosing Cycle 1st Delay 79_DELAY_1 Reclosing Cycle 2nd Delay 79_DELAY_2 Reclosing Cycle 3rd Delay 79_DELAY_3 Reclosing Cycle 4th Delay 79_DELAY_4

2.7 Circuit Breaker Failure(50BF) Setting Trip Relay TS1, TS2, TS3, TS4 Pickup Current(CB Closed) 0.50~5.00 A, 0.05 step*)

Operating Delay(Trip Timer) 0.00~60.00 sec, 0.01 step Accuracy Pickup Current 3 % of setting value Operating Time ±20 msec of setting value Dropout Time less than 40 msec, after trip relay reset Information Operation 50BF_OP


2.8 Cold Load Pick-up(COLD_LD) Setting Current Detection Level 0.50~2.50 A, 0.05 step*)

OP Delay 0~1000 sec, 1 step Reset Delay 0~1000 sec, 1 step Accuracy Pickup Current 3 % of setting value Information Pickup COLD_LD_PKP Operation COLD_LD_OP


2.9 Inrush Detection(I2/I1) Setting 2nd Harmonic of I2/I1 10~100 % , 1 step

7/24


Operating Delay 0.00~60.00 sec, 0.01step Minimum Current(at least one phase) 0.50~2.50 A, 0.05 step*)

2nd Harmonic Measuring Time 1/2 cycle Accuracy Pickup Current 3 % of setting value Operating Time ±20 msec of setting value Dropout Time less than 40 msec Information Operation I2/I_OP


3.Control 3.1 Circuit Breaker Control Setting Trip Pulse Time 0.1~5.0 sec, 0.1 step Close Pulse Time 0.1~5.0 sec, 0.1 step

3.2 EasyLogic Contact Output, LED Logic OR8(8 input OR) , HALF-OR8(Non inverting 4 input & inverting 4 input OR) , AND8(8 input AND) , HALF-AND8(Non inverting 4 input & inverting 4 input AND)Input Reference PAC-E100 Logic Input DiagramReset Type Self(latched until delay timer is expired) , Manual(latched until annunciator reset is issued) Self Reset Delay 0.00~60.00sec(0.01sec step) Conditional automatic reset for LED Last fault only is annuciated. Contact Input Function Not Connected , CB Open , CB Close , Remote Annunciator Reset , Protection Block , General Input , TCS Input

8/24


Logic Design (Contact Output & LED)

Input#1Input#2Input#3Input#4Input#5Input#6Input#7Input#8




Logic

0.00 ~ 60.00

Reset Type= Self

R

S Q

Reset Type= Manual

Annunciator

Contact Out#1 ~ #4

LED#1~#4

<PAC-E100 Logic Input> Input Group Input Description

L_OFF Logic ‘0’ Logic

L_ON Logic ‘1’ CB_OPEN_CTL CB Open Control(Local or Remote) CB_CLOSE_CTL CB Close Control(Local or Remote) 79_OPEN_CMD Auro-Reclosing CB open command

CB control

79_CLOSE_CMD Auto-Reclosing CB close command CONT_IN #1 Contact input#1 status

… … Contact inputs CONT_IN #4 Contact input#4 status

System SYS_ERR Self-diagnosis error is occurred PROT_PKP_OR Any protection element is picked up PROT_OP_OR Any protection element is operated 50_1_PKP_OR At least 1 phase of 50_1 is picked up 50_1_PKP_A Phase A of 50_1 is picked up 50_1_PKP_B Phase B of 50_1 is picked up 50_1_PKP_C Phase C of 50_1 is picked up 50_1_OP_OR At least phase of 50_1 is operated 50_1_OP_A Phase A of 50_1 is operated 50_1_OP_B Phase B of 50_1 is operated 50_1_OP_C Phase C of 50_1 is operated 50_2_PKP_OR At least 1 phase of 50_2 is picked up

Protection elements

50_2_PKP_A Phase A of 50_2 is picked up

9/24


50_2_PKP_B Phase B of 50_2 is picked up 50_2_PKP_C Phase C of 50_2 is picked up 50_2_OP_OR At least phase of 50_2 is operated 50_2_OP_A Phase A of 50_2 is operated 50_2_OP_B Phase B of 50_2 is operated 50_2_OP_C Phase C of 50_2 is operated 51_PKP_OR At least 1 phase of 51 is picked up 51_PKP_A Phase A of 51 is picked up 51_PKP_B Phase B of 51 is picked up 51_PKP_C Phase C of 51 is picked up 51_OP_OR At least phase of 51 is operated 51_OP_A Phase A of 51 is operated 51_OP_B Phase B of 51 is operated 51_OP_C Phase C of 51 is operated 50N_1_PKP 50N_1 is picked up 50N_1_OP 50N_1 is operated 50N_2_PKP 50N_2 is picked up 50N_2_OP 50N_2 is operated 51N_PKP 51N is picked up 51N_OP 51N is operated 37_PKP_OR At least 1 phase of 37 is picked up 37_PKP_A Phase A of 37 is picked up 37_PKP_B Phase B of 37 is picked up 37_PKP_C Phase C of 37 is picked up 37_OP_OR At least phase of 37 is operated 37_OP_A Phase A of 37 is operated 37_OP_B Phase B of 37 is operated 37_OP_C Phase C of 37 is operated 49_ALARM 49 is alarmed 49_OP 49 is operated 46_PKP 46 is picked up 46_OP 46 is operated 79_READY 79 ready 79_IN_PROG 79 is in progressing 79_FAIL 79 is failed 50BF_OP 50BF is operated COLD_LD_PKP Cold load pickup is picked up COLD_LD_OP Cold load pickup is operated

I2/I_OP 2nd harmonic Inrush condition is operated

10/24


4. Monitoring 4.1 Self-Diagnosis Memory After power-on reset, RAM pattern test error Setting When power-on reset or setting is changed, Non-volatile memory setting is checked. Setting value is out of boundary Total check-sum Error A/D Converter A/D running counter stop , A/D reference input is out of boundary Auto-Calibration Each analog input calibration factor is out of boundary , Ttotal check-sum error Trip Circuit Supervision Only One DI is used for TSC. If contact input function setting set to ‘TCS input, then trip circuit supervision function is enabled. TCS DI Input is checked every 600 msec. If consecutive 100 is failed, TCS fail annunciation is reported. After TSC fail is cleared, the failure annunciation is reset automatically.

5. Measurement Current Phase, Ground Current RMS Input Range 0.5~250 A*)

Accuracy ±2 %(0.5~1 A), ±0.5 %(1~6 A) *)

Sequence Current Positive/Negative/Zero Sequence Current RMS

Frequency Range 40 Hz~70 Hz, Phase A Current Accuracy ±0.03 Hz at Nominal current input


6. Record 6.1 Events(Include Fault Information) Storage Capacity Max. 128 events with 1 msec time resolution Data System reset , Annuciator reset , Setting changed , Clear event record , Clear waveform recording , Protection pickup/operate/release etc. Analog input information(current rms) are recorded when a protection element triggered.

6.2 Waveform Storage Capacity Max. 20 Record Type(block*cycle) 10 * 6(300 msec, 50Hz) or 20 * 3 , for 16 sample per cycle 10 * 12, 20 *6, for 8 sample per cycle Trigger Position 0 ~ 99%

11/24


Trigger Source Protection trip , Change of contact input status Data Current sample(IA, IB, IC, IN) , Contact input/Output status , Enabled protection status

6.3 CB Trip Counter Trip counter is accumulated in non-volatile memory after only protection trip is issued. Trip Counter range are 0 to 65535, free running(roll-over). This counter can be edit by local front key operation.

7.Communication 7.1 RS-232 Front Panel 19200 bps (fixed), Modbus protocol Rear Panel Physically identical port to front panel RS-232C

7.2 RS-485 Galvanic isolated BPS 300~38400 bps Protocol Modbus, DNP3.0, IEC60870-5-103

8.PC Software Relay setting upload and download. Event upload from relay and save to file. Waveform upload from relay and analysis in PC supported.

12/24


9. Mounting and Dimensions

Panel Mounting, Draw-out type

E

29

28

15

14

13

27

26

25

24

23

22

21

20

12

11

10

9

8

7

6

5

19

18

17

16

4

3

2

1

RS-485 RS-232

13/24


Rear Terminal Block

PAC-E110 No Description No Description 16 IA+ 1 IA- 17 IB+ 2 IB- 18 IC+ 3 IC- 19 IN+ 4 IN- 20 - 5 - 21 TS1_COM 6 TS1_NO 22 TS2_COM 7 TS2_NO 23 TS3_COM 8 TS3_NO 24 TS4_COM 9 TS3_NC 25 TS4_NC 10 TS4_NO 26 DI1_COM 11 DI1_P 27 DI2_COM 12 DI2_P 28 PWR+ 13 DI3_P 29 PWR- 14 DI4_P 30 FG 15 DI3_4_COM

14/24


10. External Connection Diagram

C B A

25

PAC-E110

RS485 (Rear)

RS232 (front)

DB-9DB-9

TS4_NC

TS4_COM TS4_NO

28 29

PWR-

11 DI1_P DI1_COM

DI2-P DI2_COM

12

TS1_NO TS1_COM

6 21

10 24

TS2_NO

TS3_NO

7

9

22

8

26

27

TS2_COM

TS3_NC TS3_COM

13 DI3 P

DI4 P DI3_4_COM

14 15

23

IN

IC

IB

IA

194

18 3

172

116

30

PWR+

Aux Power

AC/DC 110~220V

<External Connection Diagram of PAC-E110>

15/24


11.Ordering Information Power Supply 125 VDC/110 VAC or 250 VDC/220 VAC 24/48 VDC CT Rated Secondary 1 A or 5 A Language English, Turkish

16/24


12. LCD Menu Configuration

- DISPLAY

DISPLAY (ENT)

↓ CONTAC INPUT ↔ ↕ CONT IN#1~#4 OFF / ON

↕ CONTACT OUTPUT ↔ ↕ CONT OUT#1~#4 DEENERGIZED / ENERGIZED

↓ MEMORY FAIL / OK

↕ SETTING FAIL / OK

↕ AD CONVERTER FAIL / OK

↕ CALIBRATION FAIL / OK

↕ SELF DIAGNOSIS ↔

↑ TRIP CIRCUIT FAIL / OK

↓ IOC1(50_1) Pickup, Operation

↕ IOC2(50_2) Pickup, Operation

↕ TOC(51) Pickup, Operation

↕ IOCG1(50N_1) Pickup, Operation

↕ IOCG2(50N_2) Pickup, Operation

↕ TOCG(51N) Pickup, Operation

↕ THERMAL(49) Alarm, Operation

↕ UC(37) Pickup, Operation

↕ NSOC(46) Pickup, Operation

↕ AREL(79) Ready, In Progress, Fail

↕ CBFAIL(50BF) Operation

↓ STATUS ↔

↑ PROTECTION ↔

↕ COLD LD(COLD_LD) Pickup, Operation

17/24


↑ INRUSH(I2/I) Operation

↓ CURR(IA)

↕ CURR(IB)

↕ CURR(IC)

↕ CURR(IN)

↕ SEQ(I0)

↕ SEQ(I1)

↕ SEQ(I2)

↕ FREQUENCY

↕ MEASURE ↔

↑ TRIP COUNTER

↑ SYSTEM INFO.↔ Version Display

- SETTING/SYSTEM

SETTING (ENT) Function Range (Step)

↓ FREQUENCY 50/60 Hz

↕ PHS CT RATIO 1A : 1 ~ 6000 : 1 (1)

5A : 1 ~ 6000 : 5 (1)

↓ POWER SYSTEM ↔

↕ GND CT RATIO 1A : 1 ~ 6000 : 1 (1) 5A : 1 ~ 6000 : 5 (1)

↓ TRIP PULSE 0.1 ~ 5.0s (0.1) ↕ CB CONTROL ↔

↑ CLOSE PULSE 0.1 ~ 5.0s (0.1)

↓ SYSTEM ↔

↕ COM ↔ ↓ FUNCTION DISALBE / ENABLE

18/24


↕ SLAVE ADDR 1 ~ 65534 (1)

↕ BPS 300 / 1200 / 2400 / 4800 / 9600 / 19200 / 38400

↑ PROTOCOL DNP3.0 / MODBUS / IEC870

↓ TX DELAY 0 ~ 65000 (1)

↕ LINK CONFIRM NEVER / ALWAYS / SOMETIMES

↕ LINK RETRY 0 ~ 5 (1)

↕ LINK TIMEOUT 1 ~ 65000 (1)

↕ SBO TIMEOUT 1 ~ 65000 (1)

↕ WR TIME INT 0 ~ 65000 (1)

↕ DNP3.0 ↔

↑ COLD RESTART DISABLE / ENABLE

↕ CONTACT INPUT ↔ ↕ CONT IN#1~#4 NOT_CONNECTED / CB_OPENED / CB_CLOSED / ANNUN_RESET / PROT_BLOCK / GENERAL_INPUT

↓ LOGIC OR8 / HALF_OR8 / AND8 / HALF_AND8

↕ INPUT#1 Reference







↕ CONTACT OUTPUT

/ CONT OUT#1~#4 ↔


19/24


↕ RESET TYPE SELF / MANUAL

↑ RESET DELAY 0.00 ~ 60.00s (0.01)

↓ LOGIC OR8 / HALF_OR8 / AND8 / HALF_AND8









↕ RESET TYPE SELF / MANUAL

↕ LED

/ LED#1~#4 ↔

↑ RESET DELAY 0.00 ~ 60.00s (0.01)

↑ PASSWORD ↔ NEW PASSWORD : ****

0~9, 0~9, 0~9, 0~9

- SETTING/PROTECTION

SETTING (ENT) Function Range/Step

↓ FUNCTION DISABLE / ENABLE

↕ PICKUP 1A : 0.10~20.00A (0.01) 5A : 0.50~100.00A (0.05)

↕ DELAY 0.00 ~ 60.00s (0.01)

↓ IOC1(50_1) ↔

↑ BLOCK NO / YES

↓ PROTECTION ↔

↕ IOC2(50_2) ↔ ↓ FUNCTION DISABLE / ENABLE

20/24


↕ PICKUP 1A : 0.10~20.00A (0.01) 5A : 0.50~100.00A (0.05)

↕ DELAY 0.00 ~ 60.00s (0.01)

↑ BLOCK NO / YES


↕ CURVE IEC_NI / IEC_VI / IEC_EI / IEC_LI / ANSI_I / ANSI_SI / ANSI_LI / ANSI_MI / ANSI_VI / ANSI_EI / ANSI_DI / KNI / KVI

↕ PICKUP 1A : 0.10~20.00A (0.01) 5A : 0.50~100.00A (0.05)

↕ MULTIPLIER 0.01 ~ 10.00 (0.01)

↕ RESET TYPE INST / TIMED

↕ TOC(51) ↔

↑ BLOCK NO / YES


↕ PICKUP 1A : 0.10~20.00A (0.01) 5A : 0.50~100.00A (0.05)

↕ DELAY 0.00 ~ 60.00s (0.01)

↕ IOCG1(50N_1) ↔

↑ BLOCK NO / YES


↕ PICKUP 1A : 0.10~20.00A (0.01) 5A : 0.50~100.00A (0.05)

↕ DELAY 0.00 ~ 60.00s (0.01)

↕ IOCG2(50N_2) ↔

↑ BLOCK NO / YES

↓ FUNCTION DISABLE / ENABLE ↕ TOCG(51N) ↔

↕ CURVE IEC_NI / IEC_VI / IEC_EI / IEC_LI / ANSI_I / ANSI_SI / ANSI_LI / ANSI_MI / ANSI_VI / ANSI_EI / ANSI_DI / KNI / KVI

21/24


↕ PICKUP 1A : 0.10~20.00A (0.01) 5A : 0.50~100.00A (0.05)

↕ MULTIPLIER 0.01 ~ 10.00 (0.01)

↕ RESET TYPE INST / TIMED

↑ BLOCK NO / YES


↕ K-FACTOR 0.10 ~ 4.00 (0.01)

↕ TIME CONST 1.0 ~ 999.9min (0.1)

↕ ALARM 50 ~ 100% (1)

↕ THERMAL(49) ↔

↑ BLOCK NO / YES


↕ PICKUP 1A : 0.02~1.00A (0.01) 5A : 0.10~5.00A (0.05)

↕ DELAY 0.00 ~ 180.00s (0.01)

↕ UC(37) ↔

↑ BLOCK NO / YES


↕ PICKUP 1A : 0.10~20.00A (0.01) 5A : 0.50~100.00A (0.05)

↕ DELAY 0.00 ~ 180.00s (0.01)

↑ BLOCK NO / YES

↕ MULTIPLIER 0.01 ~ 10.00 (0.01)

↕ NSOC(46) ↔

↑ BLOCK NO / YES


↕ SHOT NUM 1~4 (1)

↕ PRE CON Reference

↕ AREL(79) ↔

↕ START CON Reference

22/24


↕ PREPARE TIME 0.05~200.00s (0.01)

↕ DISCRIM TIME 0.01~5.00s (0.01)

↕ RECLAIM TIME 0.01~350.00s (0.01)

↕ 1st DLY TIME 0.01~300.00s (0.01)

↕ 2nd DLY TIME 0.01~300.00s (0.01)

↕ 3rd DLY TIME 0.01~300.00s (0.01)

↕ 4th DLY TIME 0.01~300.00s (0.01)

↑ BLOCK NO / YES


↕ TRIP RELAY TS1, TS2, TS3, TS4

↕ PICKUP 1A : 0.10~1.00A (0.01) 5A : 0.50~5.00A (0.05)

↕ DELAY 0.00 ~ 60.00s (0.01)

↕ CB FAIL(50BF)

↑ BLOCK NO / YES


↕ PICKUP 1A : 0.10~0.50A (0.01) 5A : 0.50~2.50A (0.05)

↕ OP DELAY 0~1000 s (1)

↕ RST DELAY 0~1000 s (1)

↕ COLD LD(COLD_LD)

↑ BLOCK NO / YES


↕ I2/I1 10~100% (1)

↕ MIN I1 1A : 0.10~0.50A (0.01) 5A : 0.50~2.50A (0.05)

↕ OP DELAY 0.00~60.00s (1)

↑ INRUSH(I2/I1)

↑ BLOCK NO / YES

23/24


- COMMAND

COMMAND (ENT)

↓ CONT OUT TEST ↔ ↕CONT OUT#1~#4 ↔ ↕ DEENERGIZED / ENERGIZED

↕ EVENT CLEAR →

↕ WAVE CLEAR →

↕ TRIP CNT EDIT →

↑ PANEL TEST →

24/24

PAC_E100_110_Technical_SpecV2_00(060320)

Documents

Transcript of PAC_E100_110_Technical_SpecV2_00(060320)