P992-P993 11 x 17 cvroldsite-rtd-uni.1gb.ru/tech/Kavlico/t_178.pdf14501 Princeton Avenue •...
3
14501 Princeton Avenue • Moorpark, CA 93021 Tel: (805) 523-2000 Fax: (805) 523-7125 • Web: www.kavlico.com • E-Mail: [email protected] DS-P992/P993-1/06 Note: Performance Specifications with ±0.002 Vdc supply at 25°C Pressure Ranges: 0-1, 0-2, 0-5, 0-10, (inches of H20) ±1, ±2, and ±5 Proof Pressure: 1.0 PSI (either port) Burst Pressure: 1.5 PSI (either port) Supply Voltage: 5.0 ± 0.5 Vdc Supply Current: 4mA Max. Output Voltage (Ratiometric): See “How to Order” Calibration Tolerance (at 5.0 Vdc supply and no load) Zero/Null Pressure: 0.25 Vdc ±60 mV Span: 3.75 Vdc ±60 mV Voltage Ratiometricity: ±1.5% of span Max. 4.75 to 5.25 Vdc supply Temperature Effects: ±2% of span Max. (0 to 60°C) Output Impedance: 100 Ohms Max. Operating Temperature: 0 to 60°C Storage Temperature: -40°C to +95°C Humidity: 95% RH, non-condensing Weight: 2.5 oz. Max. Electrical Termination Option A & B: 3 solderable pins, tin plated Option C: Lead wires, 24 AWG, 12” long Preferred Mounting Position: Vertical, pressure ports facing down Pressure Connection: 1/8” diameter tube fitting with barb for 3/16 ID tubing Recommended Interface Impedance: 25K Ohm Min. resistance between transducer output and ground, in parallel with 0.2 uF Max. capacitance. Over-voltage Protection: 16 Vdc Reverse Polarity Protection: -6 Vdc A typical order number has three codes, separated by two hyphens. Standard seal material is silicone. Standard pressure connection is flared tube fitting. OEM options are available. P992 or P993 Pressure Transducer Pressure Range Nominal Output Voltage Range (Ratiometric) 1 1” H20 0.25 to 4.00 Vdc 1B ±1” H20 0.25 to 4.00 Vdc 2 0-2.0” H20 0.25 to 4.00 Vdc 2B ±2” H20 0.25 to 4.00 Vdc 5 0-5.0” H20 0.25 to 4.00 Vdc 5B ±5” H20 0.25 to 4.00 Vdc 10 0-10” H20 0.25 to 4.50 Vdc Electrical Termination A PCB Mount B 3 Foot PCB (P992 only) C 2 Foot PCB with lead wires (P992 only) P992 - 5B – A Example: P992-5B-A for ±5” H20 with PCB mounting option Contact Kavlico for frequency output availability, alternative pressure ranges, pressure connections, or voltage range options. P992/P993 P992/P993 P992/P993 Specifications How To Order: P992 and P993
Transcript of P992-P993 11 x 17 cvroldsite-rtd-uni.1gb.ru/tech/Kavlico/t_178.pdf14501 Princeton Avenue •...
P992/P993 P992/P993 P992/P993DS-P992/P993 - 1/06
• Low Power Requirements• Amplified Linear Output• Frequency Output Option• Temperature Compensated• Multiple Mounting Options - PC Board Mount - P592/P593 & P792/P892 Footprint Compatible
• Pressure Ranges from 1” H20 through 10” H20• Ideal for VAV, Static Pressure Controls, Filter Applications & Medical Equipment• No Position Sensitivity• Superior Output Signal Stability• EMI/RFI & ESD Protection• Made in USA
Kavlico’s sophisticated manufacturing practices have earned the highest quality awards from its customers. As an ISO 9001 Registered company, Kavlico is committed to total customer satisfaction.
Kavlico designs application specific sensors to meet demanding OEM requirements. Using a broad range of sensing technologies, we provide components with EMI and over-voltage protection.
Low Range DifferentialLow Range DifferentialLow Range DifferentialLow Range DifferentialPressure TransducersPressure TransducersPressure TransducersPressure Transducers
NEWNEWNEW
RoHSCompliant
RoHSCompliant
The P992 and P993 are ideal for variable air volume (VAV) systems, filter pressure monitoring, duct air flow, static pressure monitoring, gaseous leak detection, pneumatic controls, and medical equipment applications. Supplied by a regulated 5V DC power supply, the P992 and P993 provide an amplified linear output voltage proportional to differential pressure.
The innovative electronic circuitry utilizes Kavlico’s state-of-the-art, mixed-signal CMOS ASIC, which ensures high accuracy and exceptional EMI, RFI, and ESD protection. Superior stability makes this sensor the best choice for repeatable, low-pressure measurements.
The P992 replaces existing Kavlico models P582, P592, P593, P792 and P892. For many years those Kavlico products have set the industry standard for low range differential pressure measurements for a wide variety of HVAC applications. Additionally, the P992 and P993 can be specified for PCB mounting with a small footprint. The P993 is specifically configured for control systems that are integrated into damper actuators. Sensor orientation is not critical as the sensors will not exhibit mounting position effects. Precautions should be taken to prevent moisture build-up in the sensors. Key to the superior operation of the P992 and P993 pressure sensors is Kavlico’s highly stable variable capacitance-on-silicon sensing technology combined with our digitally programmable Application Specific Integrated Circuit (ASIC).
Features
Applications
Operation
Quality
OEM Designs
14501 Princeton Avenue • Moorpark, CA 93021Tel: (805) 523-2000 Fax: (805) 523-7125 • Web: www.kavlico.com • E-Mail: [email protected]
14501 Princeton Avenue • Moorpark, CA 93021Tel: (805) 523-2000 Fax: (805) 523-7125 • Web: www.kavlico.com • E-Mail: [email protected]
DS-P992/P993-1/06
Note: Performance Specifications with ±0.002 Vdc supply at 25°C
Pressure Ranges: 0-1, 0-2, 0-5, 0-10, (inches of H20) ±1, ±2, and ±5Proof Pressure: 1.0 PSI (either port)Burst Pressure: 1.5 PSI (either port)Supply Voltage: 5.0 ± 0.5 VdcSupply Current: 4mA Max.Output Voltage (Ratiometric): See “How to Order”Calibration Tolerance (at 5.0 Vdc supply and no load) Zero/Null Pressure: 0.25 Vdc ±60 mV Span: 3.75 Vdc ±60 mVVoltage Ratiometricity: ±1.5% of span Max. 4.75 to 5.25 Vdc supplyTemperature Effects: ±2% of span Max. (0 to 60°C)Output Impedance: 100 Ohms Max.
Operating Temperature: 0 to 60°CStorage Temperature: -40°C to +95°CHumidity: 95% RH, non-condensingWeight: 2.5 oz. Max.Electrical Termination Option A & B: 3 solderable pins, tin plated Option C: Lead wires, 24 AWG, 12” longPreferred Mounting Position: Vertical, pressure ports facing downPressure Connection: 1/8” diameter tube fitting with barb for 3/16 ID tubingRecommended Interface Impedance: 25K Ohm Min. resistance between transducer output and ground, in parallel with 0.2 uF Max. capacitance.Over-voltage Protection: 16 VdcReverse Polarity Protection: -6 Vdc
A typical order number has three codes, separated by two hyphens. Standard seal material is silicone. Standard pressure connection is flared tube fitting. OEM options are available.
P992 or P993 Pressure Transducer
Pressure Range Nominal Output Voltage Range (Ratiometric)
1 1” H20 0.25 to 4.00 Vdc 1B ±1” H20 0.25 to 4.00 Vdc 2 0-2.0” H20 0.25 to 4.00 Vdc 2B ±2” H20 0.25 to 4.00 Vdc 5 0-5.0” H20 0.25 to 4.00 Vdc 5B ±5” H20 0.25 to 4.00 Vdc 10 0-10” H20 0.25 to 4.50 Vdc
Electrical Termination A PCB Mount B 3 Foot PCB (P992 only) C 2 Foot PCB with lead wires (P992 only)
P992 - 5B – A
Example: P992-5B-A for ±5” H20 with PCB mounting option Contact Kavlico for frequency output availability, alternative pressure ranges, pressure connections, or voltage range options.
P992/P993 P992/P993 P992/P993Specifications
How To Order: P992 and P993
14501 Princeton Avenue • Moorpark, CA 93021 Tel: (805) 523-2000 Fax: (805) 523-7125 • Web: www.kavlico.com • E-Mail: [email protected]
P992/P993 P992/P993 P992/P993
P992 Electrical Termination Option A : P992 Electrical Termination Option C :
P992 Electrical Termination Option B :
P993 Electrical Termination:
Outline Drawings
OPTION A
OPTION A
P992/P993 P992/P993 P992/P993DS-P992/P993 - 1/06
• Low Power Requirements• Amplified Linear Output• Frequency Output Option• Temperature Compensated• Multiple Mounting Options - PC Board Mount - P592/P593 & P792/P892 Footprint Compatible
• Pressure Ranges from 1” H20 through 10” H20• Ideal for VAV, Static Pressure Controls, Filter Applications & Medical Equipment• No Position Sensitivity• Superior Output Signal Stability• EMI/RFI & ESD Protection• Made in USA
Kavlico’s sophisticated manufacturing practices have earned the highest quality awards from its customers. As an ISO 9001 Registered company, Kavlico is committed to total customer satisfaction.
Kavlico designs application specific sensors to meet demanding OEM requirements. Using a broad range of sensing technologies, we provide components with EMI and over-voltage protection.
Low Range DifferentialLow Range DifferentialLow Range DifferentialLow Range DifferentialPressure TransducersPressure TransducersPressure TransducersPressure Transducers
NEWNEWNEW
RoHSCompliant
RoHSCompliant
The P992 and P993 are ideal for variable air volume (VAV) systems, filter pressure monitoring, duct air flow, static pressure monitoring, gaseous leak detection, pneumatic controls, and medical equipment applications. Supplied by a regulated 5V DC power supply, the P992 and P993 provide an amplified linear output voltage proportional to differential pressure.
The innovative electronic circuitry utilizes Kavlico’s state-of-the-art, mixed-signal CMOS ASIC, which ensures high accuracy and exceptional EMI, RFI, and ESD protection. Superior stability makes this sensor the best choice for repeatable, low-pressure measurements.
The P992 replaces existing Kavlico models P582, P592, P593, P792 and P892. For many years those Kavlico products have set the industry standard for low range differential pressure measurements for a wide variety of HVAC applications. Additionally, the P992 and P993 can be specified for PCB mounting with a small footprint. The P993 is specifically configured for control systems that are integrated into damper actuators. Sensor orientation is not critical as the sensors will not exhibit mounting position effects. Precautions should be taken to prevent moisture build-up in the sensors. Key to the superior operation of the P992 and P993 pressure sensors is Kavlico’s highly stable variable capacitance-on-silicon sensing technology combined with our digitally programmable Application Specific Integrated Circuit (ASIC).
Features
Applications
Operation
Quality
OEM Designs
14501 Princeton Avenue • Moorpark, CA 93021Tel: (805) 523-2000 Fax: (805) 523-7125 • Web: www.kavlico.com • E-Mail: [email protected]
14501 Princeton Avenue • Moorpark, CA 93021Tel: (805) 523-2000 Fax: (805) 523-7125 • Web: www.kavlico.com • E-Mail: [email protected]
DS-P992/P993-1/06
Note: Performance Specifications with ±0.002 Vdc supply at 25°C
Pressure Ranges: 0-1, 0-2, 0-5, 0-10, (inches of H20) ±1, ±2, and ±5Proof Pressure: 1.0 PSI (either port)Burst Pressure: 1.5 PSI (either port)Supply Voltage: 5.0 ± 0.5 VdcSupply Current: 4mA Max.Output Voltage (Ratiometric): See “How to Order”Calibration Tolerance (at 5.0 Vdc supply and no load) Zero/Null Pressure: 0.25 Vdc ±60 mV Span: 3.75 Vdc ±60 mVVoltage Ratiometricity: ±1.5% of span Max. 4.75 to 5.25 Vdc supplyTemperature Effects: ±2% of span Max. (0 to 60°C)Output Impedance: 100 Ohms Max.
Operating Temperature: 0 to 60°CStorage Temperature: -40°C to +95°CHumidity: 95% RH, non-condensingWeight: 2.5 oz. Max.Electrical Termination Option A & B: 3 solderable pins, tin plated Option C: Lead wires, 24 AWG, 12” longPreferred Mounting Position: Vertical, pressure ports facing downPressure Connection: 1/8” diameter tube fitting with barb for 3/16 ID tubingRecommended Interface Impedance: 25K Ohm Min. resistance between transducer output and ground, in parallel with 0.2 uF Max. capacitance.Over-voltage Protection: 16 VdcReverse Polarity Protection: -6 Vdc
A typical order number has three codes, separated by two hyphens. Standard seal material is silicone. Standard pressure connection is flared tube fitting. OEM options are available.
P992 or P993 Pressure Transducer
Pressure Range Nominal Output Voltage Range (Ratiometric)
1 1” H20 0.25 to 4.00 Vdc 1B ±1” H20 0.25 to 4.00 Vdc 2 0-2.0” H20 0.25 to 4.00 Vdc 2B ±2” H20 0.25 to 4.00 Vdc 5 0-5.0” H20 0.25 to 4.00 Vdc 5B ±5” H20 0.25 to 4.00 Vdc 10 0-10” H20 0.25 to 4.50 Vdc
Electrical Termination A PCB Mount B 3 Foot PCB (P992 only) C 2 Foot PCB with lead wires (P992 only)
P992 - 5B – A
Example: P992-5B-A for ±5” H20 with PCB mounting option Contact Kavlico for frequency output availability, alternative pressure ranges, pressure connections, or voltage range options.
P992/P993 P992/P993 P992/P993Specifications
How To Order: P992 and P993
