Owner's Manual,2000 Pontiac Grand Am - GMC · Steering Wheel Controls (If Equipped) Hazard Warning...

318

Transcript of Owner's Manual,2000 Pontiac Grand Am - GMC · Steering Wheel Controls (If Equipped) Hazard Warning...

Free lockout assistance

Free dead-battery assistance

Free out-of-fuel assistance

Free flat-tire change

Emergency towing

1-800-762-3743(For vehicles purchased in Canada,

call 1-800-268-6800)that provides in an emergency:

1-800-762-3743(For vehicles purchased in Canada,

call 1-800-268-6800)

Bumper-to-Bumper3-years/36,000 miles (60 000 km)

Limited Warranty

Courtesy Transportation

Every 2000

Grand Am under warranty is backed with the

following services:

i

2000 Pontiac Grand Am Owner's Manual

Litho in U.S.A.Part Number 22619480 A First Edition

© Copyright General Motors Corporation 1999All Rights Reserved

ii

Table of Contents

Keys and Door LocksRemote Keyless Entry SystemTrunk ReleaseAutomatic Transmission (If Equipped) Manual TransmissionParking BrakeWindowsTilt WheelTurn Signal/Multifunction Lever

Windshield WipersCruise ControlInterior and Exterior LampsMirrorsStorage CompartmentsConvenience Net (If Equipped)Sunroof (If Equipped)Instrument Panel, Warning Lights and Gages

Seats and Seat ControlsSafety Belts

Air Bag SystemsChild Restraints

Section 1

Section 2

Seats and Restraint Systems

Features and Controls

iii

Section 3

Comfort Controls and Audio Systems

Section 4

Your Driving and the Road

Section 5

Table of Contents (cont'd)

Defensive DrivingDrunken DrivingControl of a VehicleBrakingEnhanced Traction System

SteeringDriving Tips for Various Road ConditionsRecreational Vehicle TowingLoading Your VehicleTowing a Trailer

Heating and Air ConditioningSetting the Radio ClockRadio/Cassette Player/CD Player

Radio Theft-Deterrent FeatureSteering Wheel Controls (If Equipped)

Hazard Warning FlashersJump StartingTowing Your Vehicle

Engine OverheatingChanging a Flat TireIf You're Stuck

Problems on the Road

Table of Contents (cont'd)

Maintenance Schedule

Service and Appearance Care

Section 7

Section 6

Scheduled MaintenanceOwner Checks and ServicesPeriodic Maintenance Inspections

Recommended Fluids and LubricantsMaintenance Records

FuelChecking Fluids and LubricantsGM Oil Life System™Engine Air Cleaner/FilterBrakesBulb Replacement

Windshield Wiper Blade ReplacementTires and WheelsAppearance CareElectrical System/Fuses and Circuit BreakersCapacities and SpecificationsNormal Maintenance Replacement Parts

iv

v

Table of Contents (cont'd)

Customer Assistance Information

In the Index you will find an alphabetical listing of almost every subject in this manual. You can use it to quickly find something you want to read.

Section 8 Customer Satisfaction ProceduresCustomer Assistance OfficesRoadside Assistance and Courtesy Transportation

Warranty Information (See Warranty Manual)Reporting Safety Defects on page 8-10Service Publications

IndexSection 9

Please refer to the last page of this manual for your Service Station Guide

vi

GENERAL MOTORS, GM, the GM Emblem,PONTIAC, the PONTIAC Emblem and the name GRAND AM are registered trademarks of General Motors Corporation.

This manual includes the latest information at the time it was printed. We reserve the right to make changes in the product after that time without further notice. For vehicles first sold in Canada, substitute the name“General Motors of Canada Limited” for PontiacDivision whenever it appears in this manual.

Please keep this manual in your vehicle, so it will bethere if you ever need it when you’re on the road. If yousell the vehicle, please leave this manual in it so the newowner can use it.

We support voluntarytechnician certification.

For Canadian Owners Who Prefer aFrench Language Manual:Aux propriétaires canadiens: Vous pouvez vousprocurer un exemplaire de ce guide en français chezvotre concessionaire ou au:

DGN Marketing Services Ltd.1577 Meyerside Dr.Mississauga, Ontario L5T 1B9

vii

How to Use this ManualMany people read their owner’s manual from beginningto end when they first receive their new vehicle. If youdo this, it will help you learn about the features andcontrols for your vehicle. In this manual, you’ll find that pictures and words work together to explain things quickly.

Safety Warnings and SymbolsYou will find a number of safety cautions in this book.We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignorethe warning.

CAUTION:

These mean there is something that could hurtyou or other people.

In the caution area, we tell you what the hazard is. Then we tell you what to do to help avoid or reduce thehazard. Please read these cautions. If you don’t, you orothers could be hurt.

You will also find a circlewith a slash through it inthis book. This safetysymbol means “Don’t,”“Don’t do this” or “Don’tlet this happen.”

viii

Vehicle Damage WarningsAlso, in this book you will find these notices:

NOTICE:

These mean there is something that coulddamage your vehicle.

In the notice area, we tell you about something that candamage your vehicle. Many times, this damage wouldnot be covered by your warranty, and it could be costly.But the notice will tell you what to do to help avoid the damage.

When you read other manuals, you might see CAUTIONand NOTICE warnings in different colors or in different words.

You’ll also see warning labels on your vehicle. They usethe same words, CAUTION or NOTICE.

ix

For example,these symbolsare used on anoriginal battery:

CAUTIONPOSSIBLE

INJURY

PROTECTEYES BY

SHIELDING

CAUSTICBATTERY

ACID COULDCAUSEBURNS

AVOIDSPARKS OR

FLAMES

SPARK ORFLAMECOULD

EXPLODEBATTERY

These symbolsare importantfor you andyour passengerswhenever yourvehicle isdriven:

DOOR LOCKUNLOCK

FASTENSEAT

BELTS

POWERWINDOW

AIR BAG

These symbolshave to do withyour lamps:

MASTERLIGHTING

SWITCH

TURNSIGNALS

PARKINGLAMPS

HAZARDWARNINGFLASHER

DAYTIMERUNNING

LAMPS

FOG LAMPS

These symbolsare on some ofyour controls:

WINDSHIELDWIPER

WINDSHIELDWASHER

WINDSHIELDDEFROSTER

REARWINDOW

DEFOGGER

VENTILATINGFAN

These symbolsare used onwarning andindicator lights:

ENGINECOOLANT

TEMP

BATTERYCHARGING

SYSTEM

BRAKE

COOLANT

ENGINE OILPRESSURE

ANTI-LOCKBRAKES

Here are someother symbolsyou may see:

FUSE

LIGHTER

HORN

SPEAKER

FUEL

Vehicle SymbolsThese are some of the symbols you may find on your vehicle.

Service Station Guide

Oil ViscosityEngine Oil

See Section 6

Engine Oil DipstickSee Section 6

Use unleaded gas only,87 Octane or higher.

See Section 6

Cooling SystemSee Section 5

Hood ReleaseSee Section 6

Windshield Washer Fluid

See Section 6

Spare Tire PressureSee Section 5

BatterySee Section 6

For

a More Detailed Look at

What's Under the HoodSee Section 6

Tire PressureSee Section 6

1-1-1

Section 1 Seats and Restraint Systems

Here you’ll find information about the seats in your vehicle and how to use your safety belts properly. You can alsolearn about some things you should not do with air bags and safety belt.

1- 2 Seats and Seat Controls1- 9 Safety Belts: They’re for Everyone1- 13 Here Are Questions Many People Ask About

Safety Belts -- and the Answers1- 14 How to Wear Safety Belts Properly1- 14 Driver Position1- 22 Safety Belt Use During Pregnancy1- 23 Right Front Passenger Position1- 23 Supplemental Restraint System (SRS)1- 30 Rear Seat Passengers

1- 33 Rear Safety Belt Comfort Guides for Children and Small Adults

1- 35 Center Passenger Position1- 37 Children1- 39 Child Restraints1- 50 Larger Children1- 53 Safety Belt Extender1- 53 Checking Your Restraint Systems1- 53 Replacing Restraint System Parts After

a Crash

1-2

Seats and Seat ControlsThis section tells you about the seats -- how to adjust them -- and also about reclining seatbacks and head restraints.

Manual Seats

CAUTION:

You can lose control of the vehicle if you try toadjust a manual driver’s seat while the vehicle ismoving. The sudden movement could startle andconfuse you, or make you push a pedal when youdon’t want to. Adjust the driver’s seat only whenthe vehicle is not moving.

2-Way Manual Seat Controls

Lift the bar under the front of the seat to unlock it. Slide the seat to where you want it and release the bar.Try to move the seat with your body to be sure the seatis locked in place.

1-3

Power Lift Seat-Forward/RearwardControls (If Equipped)

Move the control lever under the front of the seat tounlock it. Slide the seat to where you want it. Thenrelease the lever and try to move the seat with your body to make sure the seat is locked into place.

Power Lift Seat-Height Controls (If Equipped)

The power seat switch is located on the lower left sideof the driver’s seat. Raise the seat by holding the switchup. Lower the seat by holding the switch down.

1-4

6-Way Power Seat Controls (If Equipped)

The power seat switch is located on the lower left sideof the driver’s seat. This switch allows you to move theseat up, down, forward, and backward. It also moves thefront of the seat up or down and the rear of the seat upor down.

Move the seat higher by lifting and holding the bottomof the switch. Lower the seat by pushing and holding thetop of the switch.

To move the seat forward, push the rear of the switchforward. To move the seat backward, push the front ofthe switch rearward.

Raise the front of the seat by lifting and holding thebottom front end of the switch. Lower the front of the seat by pushing and holding the top front end of the switch.

Raise the rear of the seat by lifting and holding thebottom rear of the switch. Lower the rear of the seat by pushing and holding the top rear of the switch.

1-5

Manual Lumbar Support (If Equipped)Turn the knob on the right front of the driver’s seatcushion to the clockwise or counterclockwise to adjustsupport of the lower back.

Reclining Front Seatbacks

To adjust the seatback, lift the lever on the outer side ofthe seat and move the seatback to where you want it.Release the lever to lock the seatback. Pull up on thelever and the seat will go to an upright position.

1-6

But don’t have a seatback reclined if your vehicle is moving.

CAUTION:

Sitting in a reclined position when your vehicle isin motion can be dangerous. Even if you buckleup, your safety belts can’t do their job whenyou’re reclined like this.The shoulder belt can’t do its job because itwon’t be against your body. Instead, it will be in front of you. In a crash you could go into it,receiving neck or other injuries.The lap belt can’t do its job either. In a crash thebelt could go up over your abdomen. The beltforces would be there, not at your pelvic bones.This could cause serious internal injuries.For proper protection when the vehicle is inmotion, have the seatback upright. Then sit well back in the seat and wear your safety belt properly.

1-7

Head RestraintsSlide the head restraint up or down so that the top of therestraint is closest to the top of your ears. This positionreduces the chance of a neck injury in a crash.

Seatback Latches (2-Door Models)

CAUTION:

If the seatback isn’t locked, it could moveforward in a sudden stop or crash. That couldcause injury to the person sitting there. Alwayspress rearward on the seatback to be sure it is locked.

The front seatback folds forward to let people get intothe back seat. The seatback latch is designed forone-handed operation.

To fold a front seatback forward, lift the seatback latchfully without pushing forward on the seatback.

Push the seatback to its original position, the seatbackwill lock.

1-8

Easy Entry Seat (2-Door Models)

CAUTION:

If an easy entry right front seat isn’t locked, itcan move. In a sudden stop or crash, the personsitting there could be injured. After you’ve usedit, be sure to push rearward on an easy entry seatto be sure it is locked.

The right front seat of your vehicle makes it easy to getin and out of the rear seat.

1. Fold the right front seatback forward by lifting theseatback latch fully.

2. The seat will slide forward to allow someone to getinto the rear seat area.

3. Push the seatback upright to lock and slide the seatfully rearward to lock.

4. The front passenger should try to move the seat tomake sure the seat is locked into place.

Rear Seats

Folding the Rear Seat

To fold down the rear seat,pull the release strapslocated in the trunk.

Fold the seatback down from inside the vehicle. Theright strap operates the right rear split seat. The left strapoperates the left rear split seat.

Push the seatback up to return it to its original position.

To make sure the seatback is secure, push the seatbackinto a fully upright position. Pull the seatback forwardslightly to make sure that it is latched. The seatbackshould not fold down.

1-9

Safety Belts: They’re for EveryoneThis part of the manual tells you how to use safety beltsproperly. It also tells you some things you should not dowith safety belts.

And it explains the Supplemental Restraint System (SRS),or air bag system.

CAUTION:

Don’t let anyone ride where he or she can’t weara safety belt properly. If you are in a crash andyou’re not wearing a safety belt, your injuriescan be much worse. You can hit things inside thevehicle or be ejected from it. You can be seriouslyinjured or killed. In the same crash, you mightnot be if you are buckled up. Always fasten yoursafety belt, and check that your passengers’ beltsare fastened properly too.

CAUTION:

It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision,people riding in these areas are more likely to beseriously injured or killed. Do not allow people to ride in any area of your vehicle that is notequipped with seats and safety belts. Be sureeveryone in your vehicle is in a seat and using asafety belt properly.

Your vehicle has a light thatcomes on as a reminder tobuckle up. (See “Safety Belt Reminder Light” in the Index.)

1-10

In most states and Canadian provinces, the law says towear safety belts. Here’s why: They work.

You never know if you’ll be in a crash. If you do have a crash, you don’t know if it will be a bad one.

A few crashes are mild, and some crashes can be soserious that even buckled up a person wouldn’t survive.But most crashes are in between. In many of them,people who buckle up can survive and sometimes walkaway. Without belts they could have been badly hurt or killed.

After more than 30 years of safety belts in vehicles, the facts are clear. In most crashes buckling up doesmatter ... a lot!

Why Safety Belts WorkWhen you ride in or on anything, you go as fast as it goes.

Take the simplest vehicle. Suppose it’s just a seat on wheels.

1-11

Put someone on it. Get it up to speed. Then stop the vehicle. The riderdoesn’t stop.

1-12

The person keeps going until stopped by something.

In a real vehicle, it could be the windshield ...

or the instrument panel ...

1-13

or the safety belts!

With safety belts, you slow down as the vehicle does.You get more time to stop. You stop over more distance,and your strongest bones take the forces. That’s whysafety belts make such good sense.

Here Are Questions Many People AskAbout Safety Belts -- and the AnswersQ: Won’t I be trapped in the vehicle after an

accident if I’m wearing a safety belt?

A: You could be -- whether you’re wearing a safetybelt or not. But you can unbuckle a safety belt,even if you’re upside down. And your chance ofbeing conscious during and after an accident, soyou can unbuckle and get out, is much greater ifyou are belted.

Q: If my vehicle has air bags, why should I have towear safety belts?

A: Air bags are in many vehicles today and will be in most of them in the future. But they aresupplemental systems only; so they work withsafety belts -- not instead of them. Every air bagsystem ever offered for sale has required the use ofsafety belts. Even if you’re in a vehicle that has airbags, you still have to buckle up to get the mostprotection. That’s true not only in frontal collisions,but especially in side and other collisions.

1-14

Q: If I’m a good driver, and I never drive far fromhome, why should I wear safety belts?

A: You may be an excellent driver, but if you’re in anaccident -- even one that isn’t your fault -- you and your passengers can be hurt. Being a gooddriver doesn’t protect you from things beyond your control, such as bad drivers.

Most accidents occur within 25 miles (40 km) of home. And the greatest number of seriousinjuries and deaths occur at speeds of less than 40 mph (65 km/h).

Safety belts are for everyone.

How to Wear Safety Belts ProperlyAdultsThis part is only for people of adult size.

Be aware that there are special things to know aboutsafety belts and children. And there are different rulesfor smaller children and babies. If a child will be riding in your vehicle, see the part of this manual called “Children.” Follow those rules for everyone’s protection.

First, you’ll want to know which restraint systems your vehicle has.

We’ll start with the driver position.

Driver PositionThis part describes the driver’s restraint system.

Lap-Shoulder BeltThe driver has a lap-shoulder belt. Here’s how to wear it properly.

1. Close and lock the door.

2. Adjust the seat (to see how, see “Seats” in the Index)so you can sit up straight.

1-15

3. Pick up the latch plate and pull the belt across you.Don’t let it get twisted.

The shoulder belt may lock if you pull the belt acrossyou very quickly. If this happens, let the belt go backslightly to unlock it. Then pull the belt across youmore slowly.

4. Push the latch plate into the buckle until it clicks.

Pull up on the latch plate to make sure it is secure. If the belt isn’t long enough, see “Safety BeltExtender” at the end of this section.

Make sure the release button on the buckle ispositioned so you would be able to unbuckle thesafety belt quickly if you ever had to.

1-16

5. To make the lap part tight, pull down on the buckleend of the belt as you pull up on the shoulder belt.

The lap part of the belt should be worn low and snug onthe hips, just touching the thighs. In a crash, this appliesforce to the strong pelvic bones. And you’d be less likelyto slide under the lap belt. If you slid under it, the beltwould apply force at your abdomen. This could causeserious or even fatal injuries. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.

The safety belt locks if there’s a sudden stop or crash, or if you pull the belt very quickly out of the retractor.

1-17

Shoulder Belt Height Adjuster (4-Door Models)

Before you begin to drive, move the shoulder beltadjuster to the height that is right for you.

To move it down, squeeze the release button and movethe height adjuster to the desired position. You can movethe adjuster up just by pushing on the shoulder beltguide. After you move the adjuster to where you want it,try to move it down without squeezing the release buttonto make sure it has locked into position.

Adjust the height so that the shoulder portion of the belt is centered on your shoulder. The belt should beaway from your face and neck, but not falling off your shoulder.

1-18

Q: What’s wrong with this?

A: The shoulder belt is too loose. It won’t give nearlyas much protection this way.

CAUTION:

You can be seriously hurt if your shoulder belt istoo loose. In a crash, you would move forwardtoo much, which could increase injury. Theshoulder belt should fit against your body.

1-19

Q: What’s wrong with this?

A: The belt is buckled in the wrong place.

CAUTION:

You can be seriously injured if your belt is buckledin the wrong place like this. In a crash, the beltwould go up over your abdomen. The belt forceswould be there, not at the pelvic bones. This couldcause serious internal injuries. Always buckle yourbelt into the buckle nearest you.

1-20

Q: What’s wrong with this?

A: The shoulder belt is worn under the arm. It shouldbe worn over the shoulder at all times.

CAUTION:

You can be seriously injured if you wear theshoulder belt under your arm. In a crash, yourbody would move too far forward, which wouldincrease the chance of head and neck injury.Also, the belt would apply too much force to theribs, which aren’t as strong as shoulder bones.You could also severely injure internal organslike your liver or spleen.

1-21

Q: What’s wrong with this?

A: The belt is twisted across the body.

CAUTION:

You can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt istwisted, make it straight so it can work properly,or ask your dealer to fix it.

1-22

To unlatch the belt, just push the button on the buckle.The belt should go back out of the way.

Before you close the door, be sure the belt is out of theway. If you slam the door on it, you can damage both thebelt and your vehicle.

Safety Belt Use During PregnancySafety belts work for everyone, including pregnantwomen. Like all occupants, they are more likely to beseriously injured if they don’t wear safety belts.

A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible,below the rounding, throughout the pregnancy.

1-23

The best way to protect the fetus is to protect themother. When a safety belt is worn properly, it’s morelikely that the fetus won’t be hurt in a crash. Forpregnant women, as for anyone, the key to makingsafety belts effective is wearing them properly.

Right Front Passenger PositionTo learn how to wear the right front passenger’s safety beltproperly, see “Driver Position” earlier in this section.

The right front passenger’s safety belt works the sameway as the driver’s safety belt -- except for one thing. If you ever pull the shoulder portion of the belt out all the way, you will engage the child restraint lockingfeature. If this happens, just let the belt go back all theway and start again.

Supplemental Restraint System (SRS)This part explains the Supplemental Restraint System(SRS) or air bag system.

Your vehicle has air bags -- one air bag for the driverand another air bag for the right front passenger.

Frontal air bags are designed to help reduce the risk ofinjury from the force of an inflating air bag. But theseair bags must inflate very quickly to do their job andcomply with federal regulations.

Here are the most important things to know about the air bag system:

CAUTION:

You can be severely injured or killed in a crash ifyou aren’t wearing your safety belt -- even if youhave air bags. Wearing your safety belt during acrash helps reduce your chance of hitting thingsinside the vehicle or being ejected from it. Airbags are “supplemental restraints” to the safetybelts. All air bags are designed to work withsafety belts, but don’t replace them. Air bags are designed to work only in moderate to severecrashes where the front of your vehicle hitssomething. They aren’t designed to inflate at all in rollover, rear, side or low-speed frontalcrashes. And, for unrestrained occupants, air bags may provide less protection in frontalcrashes than more forceful air bags haveprovided in the past. Everyone in your vehicleshould wear a safety belt properly -- whether ornot there’s an air bag for that person.

1-24

CAUTION:

Air bags inflate with great force, faster than theblink of an eye. If you’re too close to an inflatingair bag, as you would be if you were leaningforward, it could seriously injure you. Safetybelts help keep you in position before and duringa crash. Always wear your safety belt, even withair bags. The driver should sit as far back aspossible while still maintaining control of the vehicle.

CAUTION:

Anyone who is up against, or very close to, anyair bag when it inflates can be seriously injuredor killed. Air bags plus lap-shoulder belts offerthe best protection for adults, but not for youngchildren and infants. Neither the vehicle’s safetybelt system nor its air bag system is designed forthem. Young children and infants need theprotection that a child restraint system canprovide. Always secure children properly in yourvehicle. To read how, see the part of this manualcalled “Children.”

1-25

There is an air bag readinesslight on the instrumentpanel, which shows AIR BAG.

The system checks the air bag electrical system formalfunctions. The light tells you if there is an electricalproblem. See “Air Bag Readiness Light” in the Indexfor more information.

How the Air Bag System Works

Where are the air bags?

The driver’s air bag is in the middle of the steering wheel.

1-26

The right front passenger’s air bag is in the instrumentpanel on the passenger’s side.

CAUTION:

If something is between an occupant and an air bag, the bag might not inflate properly or it might force the object into that person. Thepath of an inflating air bag must be kept clear.Don’t put anything between an occupant and anair bag, and don’t attach or put anything on thesteering wheel hub or on or near any other airbag covering.

1-27

When should an air bag inflate?

An air bag is designed to inflate in a moderate to severefrontal or near-frontal crash. The air bag will inflateonly if the impact speed is above the system’s designed“threshold level.” If your vehicle goes straight into awall that doesn’t move or deform, the threshold level isabout 9 to 14 mph (14 to 23 km/h). The threshold levelcan vary, however, with specific vehicle design, so thatit can be somewhat above or below this range. If yourvehicle strikes something that will move or deform, such as a parked car, the threshold level will be higher.The air bag is not designed to inflate in rollovers, sideimpacts or rear impacts, because inflation would nothelp the occupant.

In any particular crash, no one can say whether an airbag should have inflated simply because of the damageto a vehicle or because of what the repair costs were.Inflation is determined by the angle of the impact andhow quickly the vehicle slows down in frontal ornear-frontal impacts.

What makes an air bag inflate?

In an impact of sufficient severity, the air bag sensingsystem detects that the vehicle is in a crash. The sensingsystem triggers a release of gas from the inflator, which inflates the air bag. The inflator, air bag andrelated hardware are all part of the air bag modulesinside the steering wheel and in the instrument panel in front of the right front passenger.

How does an air bag restrain?

In moderate to severe frontal or near-frontal collisions,even belted occupants can contact the steering wheel orthe instrument panel. Air bags supplement the protectionprovided by safety belts. Air bags distribute the force ofthe impact more evenly over the occupant’s upper body,stopping the occupant more gradually. But air bagswould not help you in many types of collisions,including rollovers, rear impacts and side impacts,primarily because an occupant’s motion is not towardthose air bags. Air bags should never be regarded asanything more than a supplement to safety belts, and then only in moderate to severe frontal ornear-frontal collisions.

1-28

What will you see after an air bag inflates?

After an air bag inflates, it quickly deflates, so quickly thatsome people may not even realize the air bag inflated. Some components of the air bag module -- the steeringwheel hub for the driver’s air bag, or the instrument panelfor the right front passenger’s bag -- will be hot for a short time. The parts of the bag that come into contact with you may be warm, but not too hot to touch. There will be some smoke and dust coming from vents in thedeflated air bags. Air bag inflation doesn’t prevent thedriver from seeing or from being able to steer the vehicle,nor does it stop people from leaving the vehicle.

CAUTION:

When an air bag inflates, there is dust in the air.This dust could cause breathing problems for people with a history of asthma or otherbreathing trouble. To avoid this, everyone in thevehicle should get out as soon as it is safe to do so.If you have breathing problems but can’t get outof the vehicle after an air bag inflates, then getfresh air by opening a window or door.

In many crashes severe enough to inflate an air bag,windshields are broken by vehicle deformation.Additional windshield breakage may also occur from the right front passenger air bag.

� Air bags are designed to inflate only once. After theyinflate, you’ll need some new parts for your air bagsystem. If you don’t get them, the air bag systemwon’t be there to help protect you in another crash.A new system will include air bag modules andpossibly other parts. The service manual for yourvehicle covers the need to replace other parts.

� Your vehicle is equipped with a crash sensing anddiagnostic module, which records information aboutthe air bag system. The module records informationabout the readiness of the system, when the systemcommands air bag inflation and driver’s safety beltusage at deployment.

� Let only qualified technicians work on your air bagsystem. Improper service can mean that your air bag system won’t work properly. See your dealer for service.

1-29

NOTICE:

If you damage the covering for the driver’s or theright front passenger’s air bag, the bag may notwork properly. You may have to replace the airbag module in the steering wheel or both the airbag module and the instrument panel for theright front passenger’s air bag. Do not open orbreak the air bag coverings.

If your vehicle ever gets into a lot of water -- such aswater up to the carpeting or higher -- or if water entersyour vehicle and soaks the carpet, the air bag controllercan be soaked and ruined. If this ever happens, and thenyou start your vehicle, the damage could make the airbags inflate, even if there’s no crash. You would have toreplace the air bags as well as the sensors and relatedparts. If your vehicle is ever in a flood, or if it’s exposedto water that soaks the carpet, you can avoid needlessrepair costs by turning off the vehicle immediately anddisconnecting the battery cables. Don’t let anyone startthe vehicle under any circumstances. See your dealer for service.

Servicing Your Air Bag-Equipped VehicleAir bags affect how your vehicle should be serviced.There are parts of the air bag system in several placesaround your vehicle. You don’t want the system toinflate while someone is working on your vehicle. Your dealer and the service manual have informationabout servicing your vehicle and the air bag system. To purchase a service manual, see “Service and OwnerPublications” in the Index.

CAUTION:

For up to 10 minutes after the ignition key isturned off and the battery is disconnected, an airbag can still inflate during improper service. Youcan be injured if you are close to an air bag whenit inflates. Avoid wires wrapped with yellow tapeor yellow connectors. They are probably part of the air bag system. Be sure to follow properservice procedures, and make sure the personperforming work for you is qualified to do so.

The air bag system does not need regular maintenance.

1-30

Rear Seat PassengersIt’s very important for rear seat passengers to buckle up!Accident statistics show that unbelted people in the rearseat are hurt more often in crashes than those who arewearing safety belts.

Rear passengers who aren’t safety belted can be thrownout of the vehicle in a crash. And they can strike othersin the vehicle who are wearing safety belts.

Rear Seat Outside Passenger Positions

Lap-Shoulder Belt

The positions next to the windows have lap-shoulderbelts. Here’s how to wear one properly.

1. Pick up the latch plate and pull the belt across you.Don’t let it get twisted.

The shoulder belt may lock if you pull the belt acrossyou very quickly. If this happens, let the belt go backslightly to unlock it. Then pull the belt across youmore slowly.

2. Push the latch plate into the buckle until it clicks.

1-31

If the belt stops before it reaches the buckle, tilt thelatch plate and keep pulling until you can buckle it.

Pull up on the latch plate to make sure it is secure.

If the belt is not long enough, see “Safety BeltExtender” at the end of this section. Make sure therelease button on the buckle is positioned so youwould be able to unbuckle the safety belt quickly if you ever had to.

3. To make the lap part tight, pull down on the buckleend of the belt as you pull up on the shoulder part.

1-32

The lap part of the belt should be worn low and snug onthe hips, just touching the thighs. In a crash, this appliesforce to the strong pelvic bones. And you’d be less likelyto slide under the lap belt. If you slid under it, the beltwould apply force at your abdomen. This could causeserious or even fatal injuries. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.

The safety belt locks if there’s a sudden stop or a crash,or if you pull the belt very quickly out of the retractor.

CAUTION:

You can be seriously hurt if your shoulder belt istoo loose. In a crash, you would move forwardtoo much, which could increase injury. Theshoulder belt should fit against your body.

To unlatch the belt, just push the button on the buckle.

1-33

Rear Safety Belt Comfort Guides forChildren and Small AdultsRear shoulder belt comfort guides will provide addedsafety belt comfort for children who have outgrownchild restraints and for small adults. When installed on a shoulder belt, the comfort guide pulls the belt awayfrom the neck and head.

There is one guide for each outside passenger position inthe rear seat. To provide added safety belt comfort forchildren who have outgrown child restraints and forsmaller adults, the comfort guides may be installed onthe shoulder belts. Here’s how to install a comfort guideand use the safety belt:

1. Pull the elastic cord out from between the edge ofthe seatback and the interior body to remove theguide from its storage clip.

1-34

2. Slide the guide under and past the belt. The elasticcord must be under the belt. Then, place the guideover the belt, and insert the two edges of the belt intothe slots of the guide.

3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top.

1-35

4. Buckle, position and release the safety belt asdescribed in “Rear Seat Outside Passenger Positions”earlier in this section. Make sure that the shoulderbelt crosses the shoulder.

To remove and store the comfort guides, squeeze thebelt edges together so that you can take them out fromthe guides. Pull the guide upward to expose its storageclip, and then slide the guide onto the clip. Rotate theguide and clip inward and in between the seatback and the interior body, leaving only the loop of elasticcord exposed.

Center Passenger Position

1-36

Lap Belt

When you sit in the center seating position, you have alap safety belt, which has no retractor. To make the beltlonger, tilt the latch plate and pull it along the belt.

To make the belt shorter, pull its free end as shown untilthe belt is snug.

Buckle, position and release it the same way as the lappart of a lap-shoulder belt. If the belt isn’t long enough,see “Safety Belt Extender” at the end of this section.

Make sure the release button on the buckle is positionedso you would be able to unbuckle the safety belt quicklyif you ever had to.

1-37

ChildrenEveryone in a vehicle needs protection! That includesinfants and all children smaller than adult size. Neitherthe distance traveled nor the age and size of the travelerchanges the need, for everyone, to use safety restraints.In fact, the law in every state in the United States and inevery Canadian province says children up to some agemust be restrained while in a vehicle.

Smaller Children and Babies

CAUTION:

Children who are up against, or very close to, anyair bag when it inflates can be seriously injuredor killed. Air bags plus lap-shoulder belts offerthe best protection for adults, but not for youngchildren and infants. Neither the vehicle’s safetybelt system nor its air bag system is designed for them. Young children and infants need theprotection that a child restraint system canprovide. Always secure children properly in your vehicle.

CAUTION:

Smaller children and babies should always berestrained in a child or infant restraint. Theinstructions for the restraint will say whether it is the right type and size for your child. A very young child’s hip bones are so small that a regular belt might not stay low on the hips, as it should. Instead, the belt will likely be over thechild’s abdomen. In a crash, the belt would applyforce right on the child’s abdomen, which couldcause serious or fatal injuries. So, be sure thatany child small enough for one is always properlyrestrained in a child or infant restraint.

Infants need complete support, including support for thehead and neck. This is necessary because an infant’s neckis weak and its head weighs so much compared with therest of its body. In a frontal crash, an infant in a rear-facingrestraint settles into the restraint, so the crash forces can be distributed across the strongest part of the infant’s body, the back and shoulders. A baby should be secured in anappropriate infant restraint. This is so important that many hospitals today won’t release a newborn infant to its parents unless there is an infant restraint available forthe baby’s first trip in a motor vehicle.

1-38

CAUTION:

Never hold a baby in your arms while riding in avehicle. A baby doesn’t weigh much -- until acrash. During a crash a baby will become soheavy you can’t hold it. For example, in a crash

CAUTION: (Continued)

CAUTION: (Continued)

at only 25 mph (40 km/h), a 12-lb. (5.5 kg) babywill suddenly become a 240-lb. (110 kg) force onyour arms. The baby would be almost impossibleto hold.Secure the baby in an infant restraint.

1-39

Child RestraintsEvery time infants and young children ride in vehicles, they should have protection provided by appropriate restraints.

Q: What are the different types of add-on child restraints?

A: Add-on child restraints are available in four basictypes. When selecting a child restraint, take intoconsideration not only the child’s weight and size,but also whether or not the restraint will becompatible with the motor vehicle in which it will be used.

An infant car bed (A) is a special bed made for usein a motor vehicle. It’s an infant restraint systemdesigned to restrain or position a child on acontinuous flat surface. With an infant car bed,make sure that the infant’s head rests toward thecenter of the vehicle.

1-40

A rear-facing infant restraint (B) positions an infantto face the rear of the vehicle. Rear-facing infantrestraints are designed for infants of up to about 20 lbs. (9 kg) and about one year of age. This typeof restraint faces the rear so that the infant’s head,neck and body can have the support they need in a frontal crash. Some infant seats come in two parts -- the base stays secured in the vehicleand the seat part is removable.

1-41

A forward-facing child restraint (C-E) positions a child upright to face forward in the vehicle. These forward-facing restraints are designed tohelp protect children who are from 20 to 40 lbs. (9 to 18 kg) and about 26 to 40 inches (66 to 102 cm) in height, or up to around four years of age. One type, a convertible restraint, isdesigned to be used either as a rear-facing infantseat or a forward-facing child seat.

1-42

A booster seat (F) is designed for children who are about 40 to 60 lbs., or even up to 80 lbs. (18 to 27 kg, or even up to 36 kg), and about four to eight years of age. A booster seat isdesigned to improve the fit of the vehicle’s safetybelt system. Booster seats with shields use lap-onlybelts; however, booster seats without shields uselap-shoulder belts. Booster seats can also help achild to see out the window.

When choosing a child restraint, be sure the childrestraint is designed to be used in a vehicle. If it is, it will have a label saying that it meets federal motorvehicle safety standards.

Then follow the instructions for the restraint. You mayfind these instructions on the restraint itself or in abooklet, or both. These restraints use the belt system inyour vehicle, but the child also has to be secured withinthe restraint to help reduce the chance of personal injury.The instructions that come with the infant or childrestraint will show you how to do that. Both the owner’smanual and the child restraint instructions are important,so if either one of these is not available, obtain areplacement copy from the manufacturer.

Where to Put the RestraintAccident statistics show that children are safer if theyare restrained in the rear rather than the front seat. We atGeneral Motors therefore recommend that you put yourchild restraint in the rear seat. Never put a rear-facingchild restraint in the front passenger seat. Here’s why:

1-43

CAUTION:

A child in a rear-facing child restraint can beseriously injured or killed if the right frontpassenger’s air bag inflates. This is because theback of the rear-facing child restraint would bevery close to the inflating air bag. Always securea rear-facing child restraint in a rear seat.You may secure a forward-facing child restraintin the right front seat, but before you do, alwaysmove the front passenger seat as far back as itwill go. It’s better to secure the child restraint ina rear seat.

Wherever you install it, be sure to secure the childrestraint properly.

Keep in mind that an unsecured child restraint can movearound in a collision or sudden stop and injure people in the vehicle. Be sure to properly secure any childrestraint in your vehicle -- even when no child is in it.

Top Strap

In Canada, the law requires that forward-facing childrestraints have a top strap, and that the strap beanchored. In the United States, some child restraints alsohave a top strap. If your child restraint has a top strap, it should be anchored.

Your vehicle has top strap anchors already installed forthe rear seating positions. You’ll find them behind therear seat on the filler panel.

1-44

Anchor the top strap to this bracket. Once you have thetop strap anchored, you’ll be ready to secure the childrestraint itself.

Securing a Child Restraint in a RearOutside Seat Position

You’ll be using the lap-shoulder belt. See the earlier part about the top strap if the child restraint has one. Be sure to follow the instructions that came with thechild restraint. Secure the child in the child restraintwhen and as the instructions say.

1. Put the restraint on the seat.

2. Pick up the latch plate, and run the lap and shoulderportions of the vehicle’s safety belt through oraround the restraint. The child restraint instructionswill show you how.

1-45

Tilt the latch plate to adjust the belt if needed.

If the shoulder belt goes in front of the child’s face orneck, put it behind the child restraint.

3. Buckle the belt. Make sure the release button ispositioned so you would be able to unbuckle thesafety belt quickly if you ever had to.

1-46

4. To tighten the belt, pull up on the shoulder belt whileyou push down on the child restraint. If you’re usinga forward-facing child restraint, you may find ithelpful to use your knee to push down on the childrestraint as you tighten the belt.

5. Push and pull the child restraint in differentdirections to be sure it is secure.

To remove the child restraint, just unbuckle the vehicle’ssafety belt and let it go back all the way. The safety beltwill move freely again and be ready to work for an adultor larger child passenger.

Securing a Child Restraint in the Center Rear Seat Position

You’ll be using the lap belt. Be sure to follow theinstructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say.

See the earlier part about the top strap if the childrestraint has one.

1-47

1. Make the belt as long as possible by tilting the latchplate and pulling it along the belt.

2. Put the restraint on the seat.

3. Run the vehicle’s safety belt through or around therestraint. The child restraint instructions will showyou how.

4. Buckle the belt. Make sure the release button ispositioned so you would be able to unbuckle thesafety belt quickly if you ever had to.

5. To tighten the belt, pull its free end while you push down on the child restraint. If you’re using a forward-facing child restraint, you may find ithelpful to use your knee to push down on the childrestraint as you tighten the belt.

6. Push and pull the child restraint in differentdirections to be sure it is secure.

1-48

To remove the child restraint, just unbuckle the vehicle’ssafety belt. It will be ready to work for an adult or largerchild passenger.

Securing a Child Restraint in the Right Front Seat Position

Your vehicle has a right front passenger air bag. Neverput a rear-facing child restraint in this seat. Here’s why:

CAUTION:

A child in a rear-facing child restraint can beseriously injured or killed if the right frontpassenger’s air bag inflates. This is because theback of the rear-facing child restraint would bevery close to the inflating air bag. Always securea rear-facing child restraint in the rear seat.

Although a rear seat is a safer place, you can secure aforward-facing child restraint in the right front seat.

You’ll be using the lap-shoulder belt. See the earlier part about the top strap if the child restraint has one. Be sure to follow the instructions that came with thechild restraint. Secure the child in the child restraintwhen and as the instructions say.

1. Because your vehicle has a right front passenger airbag, always move the seat as far back as it will gobefore securing a forward-facing child restraint. (See “Seats” in the Index.)

2. Put the restraint on the seat.

3. Pick up the latch plate, and run the lap and shoulderportions of the vehicle’s safety belt through oraround the restraint. The child restraint instructionswill show you how.

If the shoulder belt goes in front of the child’s face or neck, put it behind the child restraint.

1-49

4. Buckle the belt. Make sure the release button ispositioned so you would be able to unbuckle thesafety belt quickly if you ever had to.

5. Pull the rest of the shoulder belt all the way out ofthe retractor to set the lock.

1-50

6. To tighten the belt, feed the shoulder belt back into theretractor while you push down on the child restraint.You may find it helpful to use your knee to push downon the child restraint as you tighten the belt.

7. Push and pull the child restraint in differentdirections to be sure it is secure.

To remove the child restraint, just unbuckle the vehicle’ssafety belt and let it go back all the way. The safety beltwill move freely again and be ready to work for an adultor larger child passenger.

Larger Children

Children who have outgrown child restraints shouldwear the vehicle’s safety belts.

If you have the choice, a child should sit next to awindow so the child can wear a lap-shoulder belt andget the additional restraint a shoulder belt can provide.

1-51

Accident statistics show that children are safer if theyare restrained in the rear seat. But they need to use thesafety belts properly.

� Children who aren’t buckled up can be thrown out in a crash.

� Children who aren’t buckled up can strike otherpeople who are.

CAUTION:

Never do this.Here two children are wearing the same belt. The belt can’t properly spread the impact forces.In a crash, the two children can be crushedtogether and seriously injured. A belt must beused by only one person at a time.

Q: What if a child is wearing a lap-shoulder belt,but the child is so small that the shoulder belt isvery close to the child’s face or neck?

A: Move the child toward the center of the vehicle, butbe sure that the shoulder belt still is on the child’sshoulder, so that in a crash the child’s upper bodywould have the restraint that belts provide. If thechild is sitting in a rear seat outside position, see“Rear Safety Belt Comfort Guides” in the Index. If the child is so small that the shoulder belt is stillvery close to the child’s face or neck, you mightwant to place the child in the center seat position,the one that has only a lap belt.

1-52

CAUTION:

Never do this.Here a child is sitting in a seat that has alap-shoulder belt, but the shoulder part is behindthe child. If the child wears the belt in this way, in a crash the child might slide under the belt.The belt’s force would then be applied right onthe child’s abdomen. That could cause serious orfatal injuries.

Wherever the child sits, the lap portion of the beltshould be worn low and snug on the hips, just touchingthe child’s thighs. This applies belt force to the child’spelvic bones in a crash.

1-53

Safety Belt ExtenderIf the vehicle’s safety belt will fasten around you, you should use it.

But if a safety belt isn’t long enough to fasten, yourdealer will order you an extender. It’s free. When you go in to order it, take the heaviest coat you will wear, sothe extender will be long enough for you. The extenderwill be just for you, and just for the seat in your vehiclethat you choose. Don’t let someone else use it, and use it only for the seat it is made to fit. To wear it, just attach it to the regular safety belt.

Checking Your Restraint SystemsNow and then, make sure the safety belt reminder lightand all your belts, buckles, latch plates, retractors andanchorages are working properly. Look for any otherloose or damaged safety belt system parts. If you seeanything that might keep a safety belt system fromdoing its job, have it repaired.

Torn or frayed safety belts may not protect you in a crash. They can rip apart under impact forces. If a belt is torn or frayed, get a new one right away.

Also look for any opened or broken air bag covers, and have them repaired or replaced. (The air bag systemdoes not need regular maintenance.)

Replacing Restraint System PartsAfter a CrashIf you’ve had a crash, do you need new belts?

After a very minor collision, nothing may be necessary.But if the belts were stretched, as they would be if wornduring a more severe crash, then you need new belts.

If belts are cut or damaged, replace them. Collisiondamage also may mean you will need to have safety beltor seat parts repaired or replaced. New parts and repairsmay be necessary even if the belt wasn’t being used atthe time of the collision.

If your seat adjuster won’t work after a crash, the specialpart of the safety belt that goes through the seat to theadjuster may need to be replaced.

If an air bag inflates, you’ll need to replace air bagsystem parts. See the part on the air bag system earlier in this section.

2-2-1

Section 2 Features and Controls

Here you can learn about the many standard and optional features on your vehicle, and information on starting,shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything isworking properly -- and what to do if you have a problem.

2-2 Keys2-4 Door Locks2-9 Keyless Entry System If Equipped)2-12 Trunk2-14 Theft2-15 Passlock�

2-16 New Vehicle “Break-In”2-16 Ignition Switch2-17 Starting Your Engine2-20 Engine Coolant Heater (If Equipped)2-22 Automatic Transaxle Operation2-25 Manual Transaxle Operation2-27 Parking Brake2-28 Shifting Into PARK (P)

(Automatic Transaxle Only)2-30 Shifting Out of PARK (P)

(Automatic Transaxle Only)2-30 Parking Your Vehicle

(Manual Transaxle Models Only)

2-30 Parking Over Things That Burn2-31 Engine Exhaust2-32 Running Your Engine While You’re Parked

(Automatic Transaxle)2-33 Windows2-34 Tilt Wheel2-34 Turn Signal/Multifunction Lever2-41 Exterior Lamps2-44 Interior Lamps2-46 Mirrors2-48 Storage Compartments2-48 Ashtray and Lighter (If Equipped)2-49 Sun Visors2-49 Sunroof (If Equipped)2-50 The Instrument Panel-Your

Information System2-54 Warning Lights, Gages and Indicators

2-2

Keys

CAUTION:

Leaving children in a vehicle with the ignitionkey is dangerous for many reasons. A child orothers could be badly injured or even killed.

They could operate the power windows or other controls or even make the vehicle move.Don’t leave the keys in a vehicle with children.

2-3

One key is used for theignition and all locks.

When a new vehicle is delivered, the key has abar-coded key tag. This tag may be removed by your dealer before it is delivered.

Each tag has a key code on it that tells your dealer or aqualified locksmith how to make extra keys. Keep thetag in a safe place. If you lose your keys, you’ll be ableto have one made easily using this tag. If you need anew key, go to your dealer for the correct key code.Remember to carry the pre-cut emergency key whichPontiac sends after delivery (for vehicles sold in theUnited States). In an emergency, call the PontiacRoadside Assistance Program at 1-800-ROADSIDE or1-800-762-3743 (in Canada, call 1-800-268-6800).

NOTICE:

Your vehicle has a number of new features thatcan help prevent theft, therefore you can have alot of trouble getting into your vehicle if you everlock your keys inside. You may even have todamage your vehicle to get in. So be sure youhave extra keys.

2-4

Door Locks

CAUTION:

Unlocked doors can be dangerous.

Passengers -- especially children -- can easilyopen the doors and fall out. When a door islocked, the inside handle won’t open it.

Outsiders can easily enter through an unlockeddoor when you slow down or stop your vehicle.This may not be so obvious: You increase thechance of being thrown out of the vehicle in acrash if the doors aren’t locked. Wear safety beltsproperly, lock your doors, and you will be farbetter off whenever you drive your vehicle.

There are several ways to lock and unlock your vehicle.

From the outside, use your key or keyless entry system,if your vehicle has this option.

From the inside, you can lock the door by pushing thelocking lever forward.

To unlock the door, push the locking lever rearward.

2-5

Power Door LocksWith the power door locks, you can unlock or lock all of the doors of your vehicle from the driver or frontpassenger door lock switch.

Push the top of the switch to unlock all of the doors.Push the bottom of the switch to lock all the doors.

Automatic Door LocksJust close your doors and turn on the ignition. All of the doors will lock when you move your shift lever outof PARK (P) to REVERSE (R) for an automatictransaxle. All of the doors will lock when the vehiclespeed is greater than 5 mph (8 km/h) for a manualtransaxle. If someone needs to get out while the vehicleis running, have that person use the door lock. When thedoor is closed again, it will lock automatically when thevehicle reaches about 5 mph (8 km/h). All doors willautomatically unlock when the shift lever is moved toPARK (P) and when the key is turned to OFF.

Programmable Automatic Door LocksProgrammable Automatic Door Locks is a standard featureintended to provide enhanced security and convenience byautomatically locking and unlocking the doors.

One of four operating modes may be selected andprogrammed by the driver for an automatic transaxle:� Mode 1: All doors automatically lock when the

transaxle is shifted out of PARK (P). The doors willremain locked unless manually unlocked or the lockbutton is pressed. All doors will unlock when thetransaxle is shifted into PARK (P) and the key isturned to OFF.

� Mode 2: This mode is only available with the remotekeyless entry transmitter. All doors automaticallylock when the transaxle is shifted out of PARK (P).Automatic driver’s door only unlock when thetransaxle is shifted into PARK(P) and the key isturned to OFF.

� Mode 3: All doors automatically lock when thetransaxle is shifted out of PARK (P). No automaticdoor unlock.

� Mode 4: No automatic door lock or unlock.

2-6

One of the four operating modes may be selected andprogrammed by the driver for a manual transaxle:

� Mode 1: All doors automatically lock when thevehicle speed is greater than 5 mph (8 km/h). Thedoors will remain locked unless manually unlockedor the lock button is pressed. All doors will unlockwhen the transaxle is shifted into REVERSE (R) and the key is turned to OFF.

� Mode 2: This mode is only available with the remotekeyless entry transmitter. All doors automaticallylock when the vehicle speed is greater than 5 mph (8 km/h). Automatic driver’s door only unlock whenthe transaxle is shifted into REVERSE (R) and thekey is turned to OFF.

� Mode 3: All doors automatically lock when thevehicle speed is greater than 5 mph (8 km/h). No automatic door unlock.

� Mode 4: No automatic door lock or unlock.

The Programmable Automatic Door Locks will be inoperating mode 1 when the vehicle is shipped from the factory.

Disconnecting the vehicle battery for up to one year willnot change the programmed mode of the ProgrammableAutomatic Door Locks.

The operating mode of the Programmable AutomaticDoor Locks will be changed when the driver performsthe following sequence with the doors closed and thevehicle’s ignition key to ON.

To change the mode:

1. Press and hold LOCK on the power door lock switch for 10 seconds. Release the switch when youhear the chime.

2. Count the number of chimes you hear. The numberof chimes tells you which mode your vehicle is in.You can change the mode by pressing and holdingLOCK on the power door lock switch (two chimesfor mode 2, three chimes for mode 3 and four chimesfor mode 4).

3. Repeat Step 1 until you hear the number of chimesthat matches the mode you want.

The mode you selected is now set.

2-7

Delayed Locking

The Delayed Locking feature is standard and makes iteasier to use your power door locks at any time eithermanually or with the power door lock switches. Thisfeature will not operate if the key is left in the ignition.See Anti-Lockout Protection later in this section.

When the driver leaves the vehicle and pushes the powerdoor lock switch to LOCK, three chimes will be heard.The doors will not lock. Seven seconds after the driver’sdoor has been closed, all of the doors will lock, thelamps will flash and the horn will chirp.

If the driver opens another door before the seven seconds,the doors will not lock until seven seconds after the lastdoor is closed.

If the power door lock switch is pressed to LOCK twicewhen leaving the vehicle, the doors will immediately lock.

Rear Door Security Locks

Your vehicle is equippedwith rear door securitylocks that help preventpassengers from openingthe rear doors of yourvehicle from the inside.

The switch is located on the inside of the rear door. To use the security locks:

1. Move the switch up.

2. Close the door.

3. Do the same thing on the other rear door.

2-8

The rear doors of your vehicle cannot be opened fromthe inside when this feature is in use. If you want toopen a rear door when the security lock is on:

1. Unlock the door from the inside.

2. Then open the door from the outside.

If you don’t cancel the security lock feature, adults orolder children who ride in the rear won’t be able to openthe rear door from the inside. You should let adults andolder children know how these security locks work, andhow to cancel the locks.

To cancel the rear door lock:

1. Unlock the door from the inside and open it from the outside.

2. Move the switch down.

3. Do the same for the other rear door.

The rear doors will now work normally.

Anti-Lockout ProtectionAnti-Lockout Protection is a standard feature intendedto provide enhanced security and convenience. Thisfeature prevents a driver who has left the keys in theignition from locking the doors, using the power doorlocks while any door is open.

To override this feature, when the key is in the ignitionand a door is open, hold the power door lock switch forthree seconds.

This feature cannot guarantee that you will never belocked out of your vehicle. If you don’t leave the keys in the ignition, or if you use the manual door lock, or if you use the remote keyless entry transmitter (if equipped), you could still lock your keys inside yourvehicle. Always remember to take your keys with you.

Leaving Your VehicleIf you are leaving your vehicle, open your door and set the locks from the inside, then get out and close the door.

2-9

Keyless Entry System (If Equipped)If your vehicle has this feature, you can lock and unlockyour doors or unlock your trunk from about 3 feet (1 m)up to 30 feet (9 m) away using the remote keyless entrytransmitter supplied with your vehicle.

Your keyless entry system operates on a radio frequencysubject to Federal Communications Commission (FCC)Rules and with Industry Canada.

This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation.

This device complies with RSS-210 of Industry Canada.Operation is subject to the following two conditions: (1) this devic e may not cause interference, and (2) thisdevice must accept any interference received, includinginterference that may cause undesired operation of the device.

Changes or modifications to this system by other than anauthorized service facility could void authorization touse this equipment.

At times you may notice a decrease in range. This isnormal for any remote keyless entry system. If thetransmitter does not work or if you have to stand closerto your vehicle for the transmitter to work, try this:

� Check the distance. You may be too far from yourvehicle. You may need to stand closer during rainyor snowy weather.

� Check the location. Other vehicles or objects may beblocking the signal. Take a few steps to the left orright, hold the transmitter higher, and try again.

� Check to determine if battery replacement orresynchronization is necessary. See the instructionsthat follow.

� If you’re still having trouble, see your dealer or aqualified technician for service.

2-10

OperationThe following functions are available with the keylessentry system:

LOCK: All doors will automatically lock when theLOCK button on the transmitter is pressed. The interiorlamps will turn off after all of the doors are closed. If all ofthe doors are closed, the parking lamps will flash twiceand the horn will chirp to indicate locking has occurred.

UNLOCK: The driver’s door will unlock automaticallywhen the UNLOCK button on the transmitter is pressed.If the UNLOCK button is pressed again within fiveseconds, all remaining doors will unlock. The interiorlamps will stay on for 10 seconds or until the ignition isturned on. The parking lamps will flash twice to indicateunlocking has occurred.

: The trunk will unlock anytime the vehiclesymbol on the transmitter is pressed, the trunk lockout isnot engaged and the ignition is to ON along with theshift lever to PARK (P) and the parking brake isengaged or the ignition is to OFF. The interior lampswill come on for 10 seconds or until the ignition switchis turned to ON.

: The horn will chirp and the headlamps and theparking lamps will flash for up to one minute when thehorn symbol on the transmitter is pressed. The interiorlamps will come on for about 10 seconds or until theignition is turned to ON. This can be turned off bypressing the horn symbol button again or by turning the ignition to ON.

Programmable Horn Chirp

When you use the remote keyless entry transmitter tolock the doors or use the delayed locking feature, theparking lamps will flash and the horn will chirp.

The programmable horn chirp can be disabled bypressing and holding either of the door lock switches inthe unlock position for 10 seconds with the ignition toON and all of the doors closed. When you hear the hornchirp, programming is complete. To reactivate the hornchirp feature, repeat the above procedure.

2-11

Matching Transmitter(s) To Your VehicleEach remote keyless entry transmitter is coded toprevent another transmitter from unlocking your vehicle.If a transmitter is lost or stolen, a replacement can bepurchased through your dealer. Remember to bring anyremaining transmitters with you when you go to yourdealer. When the dealer matches the replacementtransmitter to your vehicle, any remaining transmittersmust also be matched. Once your dealer has coded thenew transmitter, the lost transmitter will not unlock yourvehicle. Each vehicle can have only four transmittersmatched to it.

Battery ReplacementUnder normal use, the battery in your remote keylessentry transmitter should last about two years.

You can tell the battery is weak if the transmitter won’twork at the normal range in any location. If you have toget close to your vehicle before the transmitter works,it’s probably time to change the battery.

NOTICE:

When replacing the battery, use care not to touchany of the circuitry. Static from your bodytransferred to these surfaces may damage the transmitter.

2-12

To replace the battery in the keyless entry transmitter:

1. Use a small coin or flathead screwdriver to separatethe bottom half from the top half of the transmitter.

2. Remove the battery and replace it with the new one.Make sure the positive (+) side of the battery facesdown. Use one three-volt, CR2032, or equivalent,type battery.

3. Put the two halves back together. Make sure thecover is on tightly, so water won’t get in.

4. Resynchronize and then test the transmitter.

ResynchronizationYour keyless entry system is equipped with a securitysystem that prevents anyone from recording and playingback your signal. The transmitter does not send the samesignal twice to the receiver. The receiver will not respondto a signal that has been sent to it more that once.

To resynchronize your transmitter and receiver, followthese directions:

1. Stand close to your vehicle.

2. Press and hold the LOCK and UNLOCK buttons onthe transmitter at the same time.

3. Hold the buttons for seven seconds. In this time, thedoors should lock and unlock once. This confirmsthe resynchronization. If the doors do not lock andunlock, see your dealer for service.

TrunkTo unlock the trunk from the outside, insert the key andturn the trunk lock cylinder or use the remote keylessentry transmitter (if equipped).

When closing the trunk, close from the center to ensureit fully latches.

2-13

CAUTION:

It can be dangerous to drive with the trunk lidopen because carbon monoxide (CO) gas cancome into your vehicle. You can’t see or smellCO. It can cause unconsciousness and even death.If you must drive with the trunk lid open or ifelectrical wiring or other cable connections mustpass through the seal between the body and thetrunk lid:� Make sure all other windows are shut.� Turn the fan on your heating or cooling

system to its highest speed with the settingon VENT. That will force outside air intoyour vehicle. See “Comfort Controls” in the Index.

� If you have air outlets on or under theinstrument panel, open them all the way.

See “Engine Exhaust” in the Index.

Remote Trunk Release

The remote trunk release button is located on thedriver’s door. Push the remote release button to releasethe trunk lid. Make sure the remote trunk lockout releasefeature is not activated.

The trunk will unlock when the remote trunk releasebutton is pressed, the remote trunk release lockout is toOFF and the ignition is to ON, while the shifter is toPARK (P) or the parking brake is engaged or theignition is to OFF.

2-14

Remote Trunk Release LockoutYour remote trunk release is equipped with a lockoutfeature to help prevent unauthorized entry into the trunkwhen the vehicle is left unattended. The switch islocated on the inside of the trunk lid, mounted to thetrunk lid latch.

To turn the lockout on, slide the switch all the way to theleft, to ON. To turn the lockout off, slide the switch allthe way to the right, to OFF.

When the lockout is on, the remote trunk release button on the driver’s door will not release the trunk lid.However, the trunk lid can still be opened with the key,but not with the keyless entry transmitter (if equipped).

TheftVehicle theft is big business, especially in some cities.Although your vehicle has a number of theft-deterrentfeatures, we know that nothing we put on it can make itimpossible to steal. However, there are ways you can help.

Key in the IgnitionIf you leave your vehicle with the keys inside, it’s aneasy target for joy riders or professional thieves -- sodon’t do it.

When you park your vehicle and open the driver’s door,you’ll hear a chime reminding you to remove your keyfrom the ignition and take it with you. Always do this.Your ignition and transaxle will be locked. And remember to lock the doors.

2-15

Parking at NightPark in a lighted spot, close all windows and lock yourvehicle. Remember to keep your valuables out of sight.Put them in a storage area, or take them with you.

Parking LotsIf you park in a lot where someone will be watchingyour vehicle, it’s best to lock it up and take your keys.But what if you have to leave your key?

� If possible, park in a busy, well lit area.

� Put your valuables in a storage area, like your trunk or glove box. Be sure to close and lock thestorage area.

� Close all windows.

� Move the trunk release lockout switch to the ON position.

� Lock the glove box.

� Lock all the doors except the driver’s.

� If your vehicle has a remote keyless entry system,take the transmitter with you.

Passlock�

Your vehicle is equipped with the Passlocktheft-deterrent system.

Passlock is a passive theft-deterrent system. Passlockenables fuel if the ignition lock cylinder has not beentampered with.

During normal operation, the SECURITY light will gooff approximately five seconds after the ignition key isturned to ON and the engine is started.

If the SECURITY light flashes with the key to ON, wait10 minutes until the light goes off. Then turn theignition to OFF before attempting to start the engine.

In an emergency, call the Pontiac Roadside AssistanceCenter at 1-800-ROADSIDE or 1-800-762-3743. (In Canada, call 1-800-268-6800.)

2-16

New Vehicle “Break-In”

NOTICE:

Your vehicle doesn’t need an elaborate“break -in.” But it will perform better in the longrun if you follow these guidelines:

� Don’t drive at any one speed -- fast or slow -- for the first 500 miles (805 km). Don’t make full -throttle starts.

� Avoid making hard stops for the first 200 miles (322 km) or so. During this timeyour new brake linings aren’t yet brokenin. Hard stops with new linings can meanpremature wear and earlier replacement.Follow this breaking-in guideline everytime you get new brake linings.

� Don’t tow a trailer during break -in. See “Towing a Trailer” in the Index formore information.

Ignition Switch

With the ignition key in the ignition switch, you can turnthe switch to four positions.

OFF (A): Before you put the key into the ignition switch,the switch is off. It is the only position from which youcan remove the key. With an automatic transaxle, the shiftlever must be to PARK (P) with the ignition to OFF toremove the key. With a manual transaxle, the shifter mustbe to REVERSE (R) with the ignition to OFF to removethe key. This position locks your ignition and transaxle. A warning chime will sound if you open the driver’s doorwhen the ignition is off and the key is in the ignition.

2-17

ACC (Accessory) (B): This position unlocks thetransaxle. It also lets you use things like the radio andwindshield wipers when the engine is not running. Touse ACC, turn the key clockwise to the first position.Use this position if your vehicle must be pushed ortowed, but never try to push-start your vehicle.

ON (C): This position is where the key returns after you start your engine and release the switch. The switchstays in ON when the engine is running. But even whenthe engine is not running, you can use ON to operateyour electrical power accessories and to display someinstrument panel warning lights.

START (D): This position starts the engine. When theengine starts, release the key. The ignition switch willreturn to ON for normal driving.

NOTICE:

If your key seems stuck in OFF and you can’tturn it, be sure you are using the correct key; ifso, is it all the way in? Turn the key only withyour hand. Using a tool to force it could breakthe key or the ignition switch. If none of thisworks, then your vehicle needs service.

Starting Your EngineAutomatic TransaxleMove your shift lever to PARK (P) or NEUTRAL (N).Your engine won’t start in any other position -- that’s asafety feature. To restart when you’re already moving,use NEUTRAL (N) only.

NOTICE:

Don’t try to shift to PARK (P) if your vehicle is moving. If you do, you could damage thetransaxle. Shift to PARK (P) only when yourvehicle is stopped.

Manual TransaxleThe gear selector should be in NEUTRAL and theparking brake engaged. Hold the clutch pedal to thefloor and start the engine. Your vehicle won’t start if the clutch pedal is not all the way down -- that’s asafety feature.

2-18

Starting Your 2.4 Liter L4 Engine1. With your foot off the accelerator pedal, turn your

ignition key to START. When the engine starts, letgo of the key. The idle speed will go down as yourengine warms up.

NOTICE:

Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessiveheat can damage your starter motor. Wait about15 seconds between each try to help avoiddraining your battery or damaging your starter.

2. If the engine doesn’t start right away, and if theweather is very cold (below -20� F or -29� C), pushthe accelerator pedal about one-quarter of the waydown while you turn the key to START. Do this untilthe engine starts. As soon as it does, let go of the key.

3. If your engine still won’t start (or starts but thenstops), it could be flooded with too much gasoline.Try pushing your accelerator pedal all the way to thefloor and holding it there as you hold the key inSTART for a maximum of 15 seconds. This clearsthe extra gasoline from the engine. If the engine stillwon’t start or starts briefly but then stops again,repeat step 1 or 2, depending on temperature. When the engine starts, release the key and theaccelerator pedal.

NOTICE:

Your engine is designed to work with theelectronics in your vehicle. If you add electricalparts or accessories, you could change the waythe engine operates. Before adding electricalequipment, check with your dealer. If you don’t,your engine might not perform properly.If you ever have to have your vehicle towed, seethe part of this manual that tells how to do itwithout damaging your vehicle. See “TowingYour Vehicle” in the Index.

2-19

Starting Your 3400 V6 Engine1. Without pushing the accelerator pedal, turn your

ignition key to START. When the engine starts, letgo of the key. The idle speed will go down as yourengine gets warm.

NOTICE:

Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessiveheat can damage your starter motor. Wait about15 seconds between each try to help avoiddraining your battery or damaging your starter.

2. If it doesn’t start right away, hold your key in START.If it doesn’t start in three seconds (or starts but thenstops), push the accelerator pedal about one-quarter ofthe way down for 12 more seconds, or until it starts.

3. If your engine still won’t start (or starts but thenstops), it could be flooded with too much gasoline.Try this:

Wait 15 seconds to let the starter motor cool down.Then push your accelerator pedal all the way to thefloor. Hold it there. Then hold the key in START.This clears the extra gasoline from the engine. Whenthe engine starts, let go of the key and the acceleratorpedal. If the engine still doesn’t start, wait another 15 seconds and repeat this step.

NOTICE:

Your engine is designed to work with theelectronics in your vehicle. If you add electricalparts or accessories, you could change the waythe engine operates. Before adding electricalequipment, check with your dealer. If you don’t, your engine might not perform properly.If you ever have to have your vehicle towed, see the part of this manual that tells how to do it without damaging your vehicle. See “TowingYour Vehicle” in the Index.

2-20

Engine Coolant Heater (If Equipped)

2.4L L4 Engine

3400 V6 Engine

In very cold weather, 0�F (-18�C) or colder, the enginecoolant heater can help. You’ll get easier starting andbetter fuel economy during engine warm-up. Usually,the coolant heater should be plugged in a minimum offour hours prior to starting your vehicle.

2-21

To Use the Engine Coolant Heater1. Turn off the engine.

2. Open the hood and unwrap the electrical cord. Onthe 2.4L L4 engine the engine coolant heater cord islocated in front of the engine coolant surge tank. Onthe 3400 V6 engine the engine coolant heater cord islocated near the air cleaner/filter.

3. Plug it into a normal, grounded 110-volt AC outlet.

CAUTION:

Plugging the cord into an ungrounded outletcould cause an electrical shock. Also, the wrongkind of extension cord could overheat and causea fire. You could be seriously injured. Plug thecord into a properly grounded three-prong110-volt AC outlet. If the cord won’t reach, use aheavy-duty three-prong extension cord rated forat least 15 amps.

4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it awayfrom moving engine parts. If you don’t, it could be damaged.

How long should you keep the coolant heater pluggedin? The answer depends on the outside temperature, thekind of oil you have, and some other things. Instead oftrying to list everything here, we ask that you contactyour dealer in the area where you’ll be parking yourvehicle. The dealer can give you the best advice for thatparticular area.

2-22

Automatic Transaxle OperationYour automatic transaxlehas a shift lever located on the console between the seats.

PARK (P): This locks your front wheels. It’s the bestposition to use when you start your engine because yourvehicle can’t move easily.

CAUTION:

It is dangerous to get out of your vehicle if theshift lever is not fully in PARK (P) with theparking brake firmly set. Your vehicle can roll.

Don’t leave your vehicle when the engine isrunning unless you have to. If you have left theengine running, the vehicle can move suddenly.You or others could be injured. To be sure yourvehicle won’t move, even when you’re on fairlylevel ground, always set your parking brake andmove the shift lever to PARK (P).

See “Shifting Into PARK (P)” in the Index. If you’re pulling a trailer, see “Towing a Trailer”in the Index.

2-23

Ensure the shift lever is fully in PARK (P) beforestarting the engine. Your vehicle has an automatictransaxle shift lock control. You have to apply yourregular brake before you can shift from PARK (P) whenthe ignition key is in ON. If you cannot shift out ofPARK (P), ease pressure on the shift lever and push theshift lever all the way into PARK (P) and as youmaintain brake application. Then move the shift leverinto the gear you wish. (Press the shift lever buttonbefore moving the shift lever.) See “Shifting Out ofPARK (P)” later in this section.

REVERSE (R): Use this gear to back up.

NOTICE:

Shifting to REVERSE (R) while your vehicle ismoving forward could damage your transaxle.Shift to REVERSE (R) only after your vehicle is stopped.

To rock your vehicle back and forth to get out of snow,ice or sand without damaging your transaxle, see “StuckIn Sand, Mud, Ice or Snow” in the Index.

NEUTRAL (N): In this position, your engine doesn’t connect with the wheels. To restart when you’realready moving, use NEUTRAL (N) only. Also, useNEUTRAL (N) when your vehicle is being towed.

CAUTION:

Shifting out of PARK (P) or NEUTRAL (N) whileyour engine is “racing” (running at high speed) isdangerous. Unless your foot is firmly on thebrake pedal, your vehicle could move veryrapidly. You could lose control and hit people orobjects. Don’t shift out of PARK (P) orNEUTRAL (N) while your engine is racing.

NOTICE:

Damage to your transaxle caused by shifting outof PARK (P) or NEUTRAL (N) with the engineracing isn’t covered by your warranty.

2-24

AUTOMATIC OVERDRIVE (D): This position is for normal driving. If you need more power for passing,and you’re:

� Going less than 35 mph (55 km/h), push youraccelerator pedal about halfway down.

� Going about 35 mph (55 km/h) or more, push theaccelerator all the way down. You’ll shift down tothe next gear and have more power.

NOTICE:

If your vehicle seems to start up rather slowly, orif it seems not to shift gears as you go faster,something may be wrong with a transaxle systemsensor. If you drive very far that way, yourvehicle can be damaged. So, if this happens, haveyour vehicle serviced right away. Until then, youcan use SECOND (2) when you are driving lessthan 35 mph (55 km/h) and AUTOMATICOVERDRIVE (D) for higher speeds.

THIRD (3): This position is also used for normaldriving, however, it offers more power and lower fueleconomy than AUTOMATIC OVERDRIVE (D).

Here are some times you might choose THIRD (3)instead of AUTOMATIC OVERDRIVE (D):

� When driving on hilly, winding roads.

� When towing a trailer, so there is less shiftingbetween gears.

� When going down a steep hill.

SECOND (2): This position gives you more power butlower fuel economy. You can use SECOND (2) on hills.It can help control your speed as you go down steepmountain roads, but then you would also want to useyour brakes off and on.

NOTICE:

Don’t drive in SECOND (2) for more than 25 miles (41 km), or at speeds over 55 mph (88 km/h), or you can damage your transaxle. UseAUTOMATIC OVERDRIVE (D) or THIRD (3) asmuch as possible. Don’t shift into SECOND (2)unless you are going slower than 65 mph (105 km/h) or you can damage your engine.

2-25

FIRST (1): This position gives you even more power(but lower fuel economy) than SECOND (2). You canuse it on very steep hills, or in deep snow or mud. If the selector lever is put in FIRST (1), the transaxlewon’t shift into first gear until the vehicle is goingslowly enough.

NOTICE:

If your front wheels can’t rotate, don’t try todrive. This might happen if you were stuck invery deep sand or mud or were up against a solidobject. You can damage your transaxle.Also, if you stop when going uphill, don’t holdyour vehicle there with only the acceleratorpedal. This could overheat and damage thetransaxle. Use your brakes or shift into PARK (P)to hold your vehicle in position on a hill.

Manual Transaxle OperationThis is your shift pattern.

Here’s how to operate you transaxle:

FIRST (1): Press the clutch pedal and shift into FIRST (1). Then, slowly let up on the clutch pedal asyou press the accelerator pedal.

You can shift into FIRST (1) when you are going lessthat 20 mph (32 km/h). If you have come to a completestop and it is hard to shift into FIRST (1), put the shiftlever into NEUTRAL and let up on the clutch. Press theclutch pedal back down. Then shift into FIRST (1).

SECOND (2): Press the clutch pedal as you let up onthe accelerator pedal and shift into SECOND (2). Then,slowly let up on the clutch pedal as you press theaccelerator pedal.

2-26

THIRD (3), FOURTH (4) and FIFTH (5): Shift intoTHIRD (3), FOURTH (4) and FIFTH (5) the same wayyou do for SECOND (2). Slowly let up on the clutchpedal as you press the accelerator pedal.

To stop, let up on the accelerator pedal and press the brakepedal. Just before the vehicle stops, press the clutch pedaland the brake pedal, and shift to NEUTRAL.

NEUTRAL: Use this position when you start or idleyour engine.

REVERSE (R): To back up, press down the clutchpedal and lift up on the ring on the shift lever to shiftinto REVERSE (R). Let up on the clutch pedal slowlywhile pressing the accelerator pedal.

NOTICE:

Shift into REVERSE (R) only after your vehicle isstopped. Shifting into REVERSE (R) while yourvehicle is moving could damage your transaxle.

Also, use REVERSE (R), along with the parking brakes,for parking your vehicle.

Once the transaxle is in REVERSE (R) the ignition canbe turned to OFF and the key removed.

Shift Speeds

CAUTION:

If you skip a gear when you downshift, you couldlose control of your vehicle. You could injureyourself or others. Don’t shift down more thanone gear at a time when you downshift.

Up-Shift Light (Manual Transaxle)

If you have a manualtransaxle, you may have aSHIFT light. This light willshow you when to shift tothe next higher gear for thebest fuel economy.

When this light comes on, you can shift to the nexthigher gear if the weather, road and traffic conditions letyou. For the best fuel economy, accelerate slowly andshift when the light comes on.

2-27

Parking Brake

To set the parking brake, hold the regular brake pedaldown with your right foot. Pull up on the parking brakehandle. If the ignition is on, the brake system warninglight will come on.

To release the parking brake, hold the regular brakepedal down. Pull the parking brake handle up until youcan press the release button. Hold the release button inas you move the brake handle all the way down.

NOTICE:

Driving with the parking brake on can causeyour rear brakes to overheat. You may have toreplace them, and you could also damage otherparts of your vehicle.

If you are towing a trailer and are parking on a hill, see“Towing a Trailer” in the Index. That section showswhat to do first to keep the trailer from moving.

2-28

Shifting Into PARK (P) (Automatic Transaxle Only)

CAUTION:

It can be dangerous to get out of your vehicle ifthe shift lever is not fully in PARK (P) with theparking brake firmly set. Your vehicle can roll. If you have left the engine running, the vehiclecan move suddenly. You or others could beinjured. To be sure your vehicle won’t move, evenwhen you’re on fairly level ground, use the stepsthat follow. If you’re pulling a trailer, see“Towing a Trailer” in the Index.

1. Hold the brake pedal down with your right foot andset the parking brake.

2. Move the shift lever into PARK (P) like this:

� Hold in the button on the handle.

� Push the handle all the way toward the front ofthe vehicle.

3. Move the ignition key to OFF.

4. Remove the key and take it with you. If you canleave your vehicle with the ignition key in yourhand, your vehicle is in PARK (P).

2-29

Leaving Your Vehicle With the EngineRunning (Automatic Transaxle Only)

CAUTION:

It can be dangerous to leave your vehicle with the engine running. Your vehicle could movesuddenly if the shift lever is not fully in PARK (P)with the parking brake firmly set. And, if youleave the vehicle with the engine running, it couldoverheat and even catch fire. You or others couldbe injured. Don’t leave your vehicle with theengine running unless you have to.

If you have to leave your vehicle with the enginerunning, be sure your vehicle is in PARK (P) and yourparking brake is firmly set before you leave it. Afteryou’ve moved the shift lever into PARK (P), hold theregular brake pedal down. Then, see if you can move theshift lever away from PARK (P) without first pushingthe button.

If you can, it means that the shift lever wasn’t fullylocked into PARK (P).

Torque Lock (Automatic Transaxle)If you are parking on a hill and you don’t shift yourtransaxle into PARK (P) properly, the weight of thevehicle may put too much force on the parking pawl inthe transaxle. You may find it difficult to pull the shiftlever out of PARK (P). This is called “torque lock.” To prevent torque lock, set the parking brake and thenshift into PARK (P) properly before you leave thedriver’s seat. To find out how, see “Shifting Into PARK (P)” in the Index.

When you are ready to drive, move the shift lever out ofPARK (P) before you release the parking brake.

If torque lock does occur, you may need to have anothervehicle push yours a little uphill to take some of thepressure from the parking pawl in the transaxle, so youcan pull the shift lever out of PARK (P).

2-30

Shifting Out of PARK (P) (Automatic Transaxle Only)Your vehicle has an automatic transaxle shift lockcontrol system. You have to apply your regular brakebefore you can shift from PARK (P) when the ignition isin ON. See “Automatic Transaxle” in the Index.

If you cannot shift out of PARK (P), ease pressure onthe shift lever and push the shift lever all the way intoPARK (P) as you maintain brake application. Thenmove the shift into the gear you wish. Press the shiftlever button before moving the shift lever.

If you ever hold the brake pedal down but still can’tshift out of PARK (P), try this:

1. Turn the ignition key to ACC.

2. Apply and hold the regular brake until the end of Step 5.

3. Shift to NEUTRAL (N).

4. Turn the ignition key to START, to start the vehicle.

5. Shift to the drive gear you want.

6. Have the vehicle fixed as soon as you can.

Parking Your Vehicle (Manual Transaxle Models Only)Before you get out of your vehicle, put your manualtransaxle in REVERSE (R) and firmly apply the parkingbrake. Once the transaxle is in REVERSE (R) the ignitioncan be turned to OFF and the key can be removed.

Parking Over Things That Burn

2-31

CAUTION:

Things that can burn could touch hot exhaustparts under your vehicle and ignite. Don’t parkover papers, leaves, dry grass or other things thatcan burn.

Engine Exhaust

CAUTION:

Engine exhaust can kill. It contains the gascarbon monoxide (CO), which you can’t see orsmell. It can cause unconsciousness and death.

You might have exhaust coming in if:� Your exhaust system sounds strange

or different.CAUTION: (Continued)

CAUTION: (Continued)

� Your vehicle gets rusty underneath.� Your vehicle was damaged in a collision.� Your vehicle was damaged when driving

over high points on the road or over road debris.

� Repairs weren’t done correctly.� Your vehicle or exhaust system had been

modified improperly.If you ever suspect exhaust is coming into your vehicle:� Drive it only with all the windows down to

blow out any CO; and� Have your vehicle fixed immediately.

2-32

Running Your Engine While You’reParked (Automatic Transaxle)It’s better not to park with the engine running. But if youever have to, here are some things to know.

CAUTION:

Idling the engine with the climate control systemoff could allow dangerous exhaust into yourvehicle (see the earlier Caution under “Engine Exhaust”).Also, idling in a closed-in place can let deadlycarbon monoxide (CO) into your vehicle even ifthe fan switch is at the highest setting. One placethis can happen is a garage. Exhaust -- with CO -- can come in easily. NEVER park in agarage with the engine running.Another closed-in place can be a blizzard. (See “Blizzard” in the Index.)

CAUTION:

It can be dangerous to get out of your vehicle ifthe shift lever is not fully in PARK (P) with theparking brake firmly set. Your vehicle can roll.Don’t leave your vehicle when the engine isrunning unless you have to. If you’ve left theengine running, the vehicle can move suddenly.You or others could be injured. To be sure yourvehicle won’t move, even when you’re on fairlylevel ground, always set your parking brake andmove the shift lever to PARK (P).

Follow the proper steps to be sure your vehicle won’tmove. See “Shifting Into PARK (P)” in the Index.

If you are parking on a hill and if you’re pulling atrailer, also see “Towing a Trailer” in the Index.

2-33

WindowsManual WindowsOn a vehicle with manual windows, use the windowcrank to open and close each window.

Power Windows (If Equipped)

The power window switches are located on the armrestof the driver’s door. In addition, each passenger door hasa switch for its own window.

Auto-Down Switch

The driver’s window switch has an auto-down feature.This switch is black. Push the top of the switch partway,and the driver’s window will open a small amount. If theswitch is pushed all the way, the window will go all theway down.

To stop the window while it is lowering, push the switch forward. To raise the window, push and hold the switch forward.

Lock-Out Switch

On four-door models, the driver’s power windowcontrols also include a lock-out switch. When thelock-out switch is moved to the left (with the redshowing), the driver and passengers will be able to usetheir window switches. Move the lock-out switch to theright to stop the passengers from using their windowswitches. The driver can still control all the windowswith the lock on.

HornYou can sound the horn by pressing the horn symbol onyour steering wheel.

2-34

Tilt Wheel

A tilt steering wheel allows you to adjust the steeringwheel before you drive.

You can also raise it to the highest level to give yourlegs more room when you exit and enter the vehicle.

To tilt the wheel, hold the steering wheel and pull thelever toward you.

Move the steering wheel to a comfortable level, thenrelease the lever to lock the wheel in place.

Turn Signal/Multifunction Lever

The lever on the left side of the steering columnincludes your:

� Turn Signal and Lane Change Indicator

� Headlamp High/Low Beam Changer

� Park Lamps and Headlamps Control Switch

2-35

Turn and Lane Change SignalsThe turn signal has two upward (for right) and twodownward (for left) positions. These positions allow youto signal a turn or a lane change.

To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will return automatically.

An arrow on the instrumentpanel cluster will flash inthe direction of the turn orlane change.

To signal a lane change, just raise or lower the leveruntil the arrow starts to flash. Hold it there until youcomplete your lane change. The lever will return byitself when you release it.

As you signal a turn or a lane change, if the arrows flashrapidly, a signal bulb may be burned out and otherdrivers won’t see your turn signal.

If a bulb is burned out, replace it to help avoid anaccident. If the arrows don’t go on at all when yousignal a turn, check for burned-out bulbs and then checkthe fuse (see “Fuses and Circuit Breakers” in the Index).

Headlamp High/Low Beam Changer

To change the headlampsfrom low beam to highbeam, push forward on the turn signal/multifunction lever.

To change the headlamps from high beam to low beam,pull the turn signal lever backward. If the ignition is onand the high beams are on, a light on the instrumentpanel cluster also will be on.

Flash-to-PassThis feature lets you use your high-beam headlamps tosignal a driver in front of you that you want to pass.

To use it, pull the turn signal/multifunction lever towardyou until the high-beam headlamps come on, thenrelease the lever to turn them off.

2-36

Windshield Wipers

You control the windshield wipers by moving the stalkwith the wiper symbol on it up or down.

For a single wiper cycle, push the stalk down to MIST, then release it. For more cycles, hold the stalkdown longer.

For steady wiping at low speed, move the stalk up to theLO position. For high-speed wiping, move the stalk upfurther, to HI. To stop the wipers, move the stalk to OFF.

You can set the wiper speed for a long or short delay between wipes. This can be very useful in light rain or snow.

Move the stalk to INT, then turn the inner band, labeledINT ADJ, and choose the delay you want. Turn the innerband up for shorter delay times between wiper cycles.Turn the band down for a longer delay time betweenwiper cycles.

Remember that damaged wiper blades may prevent youfrom seeing well enough to drive safely. To avoid damage,be sure to clear ice and snow from the wiper blades beforeusing them. If they’re frozen to the windshield, carefullyloosen or thaw them. If your blades do become damaged,get new blades or blade inserts.

Heavy snow or ice can overload your wiper motor. Acircuit breaker will stop the motor until it cools. Clearaway snow or ice to prevent an overload.

2-37

Windshield Washer

To wash your windshield, push in the button at the endof the stalk until the washers begin.

CAUTION:

In freezing weather, don’t use your washer untilthe windshield is warmed. Otherwise the washerfluid can form ice on the windshield, blockingyour vision.

When you release the button, the washers will stop, butthe wipers will continue to wipe for about three times orwill resume the speed you were using before.

2-38

Cruise Control (If Equipped)

The cruise control buttons are located on the bottom ofthe steering wheel.

With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot onthe accelerator. This can really help on long trips. Cruisecontrol does not work at speeds below 25 mph (40 km/h).

When you apply your brakes, the clutch pedal if youhave a manual transaxle or the parking brake, or theBRAKE light is on the cruise control will turn off.

CAUTION:

� Cruise control can be dangerous where youcan’t drive safely at a steady speed. So,don’t use your cruise control on windingroads or in heavy traffic.

� Cruise control can be dangerous onslippery roads. On such roads, fast changesin tire traction can cause needless wheelspinning, and you could lose control. Don’t use cruise control on slippery roads.

If your vehicle is in cruise control when the enhancedtraction control system begins to limit wheel spin, thecruise control will automatically disengage. (See “TractionControl System” or “Enhanced Traction System” in theIndex.) When road conditions allow you to safely use itagain, you may turn the cruise control back on.

2-39

Setting Cruise Control

CAUTION:

If you leave your cruise control switch on whenyou’re not using cruise, you might hit a buttonand go into cruise when you don’t want to. Youcould be startled and even lose control. Keep thecruise control switch off until you want to usecruise control.

1. Press the cruise control ON OFF button. The indicator on the button will turn on.

2. Get up to the speed you want.

3. Press the SET COAST button and release it. TheCRUISE light on the instrument panel will come on.

4. Take your foot off the accelerator pedal.

Resuming a Set Speed

Suppose you set your cruise control at a desired speedand then you apply the brake. This, of course, shuts offthe cruise control. But you don’t need to reset it. Onceyou’re going about 25 mph (40 km/h) or more, you canpress the cruise control RES ACCEL button for abouthalf a second.

You’ll go right back up to your chosen speed and stay there.

If you press the RES ACCEL button longer than half asecond, the vehicle will keep going faster until you releasethe button or apply the brake. So unless you want to gofaster, don’t hold down the RES ACCEL button.

Increasing Speed While Using Cruise Control

There are two ways to go to a higher speed.

� Use the accelerator pedal to get to the higher speed.Push the SET COAST button, then release the buttonand the accelerator pedal. You’ll now cruise at thehigher speed.

2-40

� Press the RES ACCEL button. Hold it there until youget up to the speed you want, and then release thebutton. To increase your speed in very small amounts,press the RES ACCEL button for less than half asecond and then release it. Each time you do this, yourvehicle will go about 1 mph (1.6 km/h) faster.

The accelerate feature will only work after you turn onthe cruise control by pushing the SET COAST button.

Reducing Speed While Using Cruise Control

There are two ways to reduce your speed while usingcruise control:

� Push the SET COAST button until you reach thelower speed you want, then release it.

� To slow down in very small amounts, push SETCOAST button for less than half a second. Each timeyou do this, you’ll go 1 mph (1.6 km/h) slower.

Passing Another Vehicle While Using Cruise Control

Use the accelerator pedal to increase your speed. Whenyou take your foot off the pedal, your vehicle will slowdown to the cruise control speed you set earlier.

Using Cruise Control on Hills

How well your cruise control will work on hills dependsupon your speed, load and the steepness of the hills. When going up steep hills, you may have to step on theaccelerator pedal to maintain your speed. When goingdownhill, you may have to brake or shift to a lower gear tokeep your speed down. Of course, applying the brake takesyou out of cruise control. Many drivers find this to be toomuch trouble and don’t use cruise control on steep hills.

Ending Out of Cruise Control

There are four ways to turn off the cruise control:

� Step lightly on the brake pedal.

� Press the cruise control RES ACCEL button and theSET COAST buttons at the same time.

� Press the cruise control ON OFF button.

� Push the clutch pedal if you have a manual transaxle.

Erasing the Cruise Speed Memory

When you turn off the cruise control or the ignition,your cruise control set speed memory is erased.

2-41

Exterior Lamps

Turn the turn signal lever end cap up one position toturn on your:

� Parking Lamps

� Side Marker Lamps

� Taillamps

� License Plate Lamps

� Instrument Panel Lights

Turn the turn signal lever end cap up two positions toturn on your:

� Headlamps

� Parking Lamps

� Sidemarker Lamps

� Taillamps

� License Plate Lamps

� Instrument Panel Lights

Turn the switch to OFF to turn all of the lamps off.

Lamps On ReminderIf you turn off the ignition and open the driver’s door while leaving the lamps on, you will hear a warning chime.

2-42

Daytime Running LampsDaytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different drivingconditions, but they can be especially helpful in theshort periods after dawn and before sunset.

The DRL system will make your high-beam headlampscome on at a reduced brightness when:

� The ignition is on,

� the headlamp switch is in OFF or you have turned onyour parking lamps,

� the light sensor detects daytime light,

� the parking brake is released and

� the shift lever is not in PARK (P) on vehicles with anautomatic transaxle.

When the DRL system is on, the taillamps, sidemarkerlamps, park lamps and instrument panel lights will notbe illuminated.

As with any vehicle, you should turn on the regularheadlamp system when you need it.

Automatic Light Control (ALC)When it is dark enough outside, your Automatic LightControl (ALC) will turn on your headlamps along withother lamps such as the taillamps, sidemarker lamps,park lamps and the instrument panel lights. The radiolights will also be dim.

Your vehicle is equipped with a light sensor on the topof the instrument panel under the defroster grill, so besure it is not covered. This will cause the ALC system tobe on whenever the ignition is on.

The ALC system may also come on when drivingthrough a parking garage, heavy overcast weather or atunnel. This is normal.

2-43

There is a delay in the transition between the daytimeand nighttime operation of the DRL and the ALCsystems so that driving under bridges or bright overheadstreet lights does not affect the system. The DRL andALC systems will only be affected when the light sensorsees a change in lighting lasting longer than this delay.

To idle your vehicle with the ALC system off, set theparking brake while the ignition is off. Then start thevehicle. The ALC system will stay off until you releasethe parking brake.

As with any vehicle, you should turn on the regularheadlamp system when you need it.

Delayed HeadlampsThe delayed headlamps feature will continue toilluminate the headlamps for 20 seconds after the key isturned to OFF then the headlamps will automaticallyturn off.

To override the 20 second delayed headlamp feature,while it is active turn the turn signal/multifunction leverend cap up one position and back to OFF.

Fog Lamps

The button for your foglamps is located on theinstrument panel, to the leftof the steering wheel, besidethe instrument panelintensity control.

When using the fog lamps, the ignition must be on aswell as the parking lamps or the low-beam headlamps.

Push the button to turn the fog lamps on. An indicatorlight on the button will glow when the fog lamps are on.Push the button again to turn the fog lamps off.

The fog lamps will turn off whenever the high-beamheadlamps are turned on. When the high beams areturned off, the fog lamps will come on again.

2-44

Interior LampsInstrument Panel Intensity Control

You can brighten or dim the instrument panel clusterlights by moving the thumbwheel to the right to increaseintensity and to the left to decrease intensity. Thethumbwheel is located on the instrument panel to the leftof the steering wheel.

Courtesy Lamp ControlWhen the thumbwheel for the instrument panel intensitycontrol is moved to the right, the dome lamp, the mirrorreading lamps (if equipped) and the footwell lamps willturn on. Move the thumbwheel to the left, to turn thelamps off.

Illuminated Entry/Exit SystemWhen you lift the driver’s door handle or open any door,the lamps inside your vehicle will go on. These lampswill fade out after about 10 seconds after all of the doorshave been closed or when the ignition is turned to ON.These lamps will also go on when you press the trunkrelease, UNLOCK or the horn symbol button on theoptional keyless entry system transmitter.

The lamps inside your vehicle will stay on for about 10 seconds after your key is removed from the ignitionto provide an illuminated exit.

2-45

Mirror Reading Lamps (If Equipped)

Press the switch on the lower front portion of the mirrorto turn on the lamps. Press the other side of the switch toturn the lamps off.

Three-Position Dome Lamp (If Equipped)

The switch on this lamp has three positions. The ONposition will turn on the light. The DOOR position willturn on the light whenever a door is opened or when theinstrument panel intensity control thumbwheel is movedto the right. The OFF position will shut off the lampcompletely, even when a door is opened.

2-46

Trunk LampThe trunk lamp comes on when you open your trunk.

Battery SaverYour vehicle is equipped with a battery saver featuredesigned to protect your vehicle’s battery.

When any interior lamp (trunk, mirror reading lamps,footwell, dome lamp or glove box) is left on when theignition is turned off, the battery saver system willautomatically shut the lamp off after 20 minutes. This will avoid draining the battery.

To reactivate the interior lamps, either:

� Lift the driver’s door handle, or

� open any door, or

� press any keyless entry transmitter button (if equipped), or

� press the power door lock switch, or

� press the remote trunk release, or

� turn the lamp that was left on to off then to on again.

MirrorsInside Day/Night Rearview Mirror

This mirror can be adjusted two ways. First, to adjustthe height of the mirror, adjust the arm that connects themirror to the windshield. Then adjust the angle of themirror, by moving the mirror to a position that allowsyou to see out of the back window.

To reduce glare from lights behind you, move the levertoward you to the night position. To return the mirror tothe daytime position, move the lever away from you.

2-47

Manual Remote Control MirrorThe outside rearview mirror should be adjusted so youcan just see the side of your vehicle when you are sittingin a comfortable driving position.

Adjust the driver’s side outside mirror with the controllever on the driver’s door.

To adjust your passenger’s side mirror, sit in the driver’sseat and have a passenger adjust the mirror for you.

Power Remote Control Mirror (If Equipped)

This selector knob controls both outsiderearview mirrors.

Select the mirror you want to adjust by turning the knobto the left or right. Adjust each mirror so that you cansee the side of your vehicle when you are sitting in acomfortable driving position.

Turn the knob to the center to turn the remote controlmirror off.

Convex Outside MirrorYour passenger’s side mirror is convex. A convexmirror’s surface is curved so you can see more from thedriver’s seat.

CAUTION:

A convex mirror can make things (like othervehicles) look farther away than they really are.If you cut too sharply into the right lane, youcould hit a vehicle on your right. Check yourinside mirror or glance over your shoulder beforechanging lanes.

2-48

Storage CompartmentsGlove BoxUse the key to lock and unlock the glove box. To open, pull the glove box handle up.

Center Console Storage AreaThe center console has two separate storage areas. Theupper compartment, which is also the armrest, can beused to store maps, gloves, etc. To open, pull up on thedriver’s side of the lid.

Rear Seat CupholderPull down the door on the rear of the center console touse the rear seat cupholder.

Convenience Net (If Equipped)Your vehicle may have a convenience net. You’ll see itjust inside the back wall of the trunk.

Put small loads, like grocery bags, behind the net. It canhelp keep them from falling over during sharp turns orquick starts and stops.

The net isn’t for larger, heavier loads. Store them in thetrunk as far forward as you can.

You can unhook the net so that it will lie flat whenyou’re not using it.

Ashtray and Lighter (If Equipped)To use the lighter, just push it in all the way and let go.

NOTICE:

Don’t put papers and other things that burn intoyour ashtrays. If you do, cigarettes or othersmoking materials could set them on fire, causing damage.

NOTICE:

Don’t hold a cigarette lighter in with your handwhile it is heating. If you do, it won’t be able toback away from the heating element when it’sready. That can make it overheat, damaging thelighter and the heating element.

You can also remove the cigarette lighter to plug inadditional accessories. Be sure to follow the properinstallation instructions that are included with anyelectrical accessory you install.

2-49

Sun VisorsTo block out glare, you can swing down the visors. You can also swing them to the side.

Visor Vanity MirrorLift the cover to expose the vanity mirror.

Sunroof (If Equipped)Open the sunshade by hand when using the vent position.

To use the vent position of the sunroof, push the switchback and release it. This is the express vent mode of the sunroof.

To fully open the sunroof, push the switch back againand release. This is the express open mode of thesunroof and sunshade.

To close the sunroof, push the switch forward and holdit until the sunroof is closed. The sunroof will stop if theswitch is released during operation. If desired, you mayclose the sunshade by hand.

The sunroof glass panel cannot be opened or closed ifyour vehicle has an electrical failure.

NOTICE:

Do not attempt to force the sunshade forward ofthe sliding glass panel. Damage will occur and thesunroof may not open or close properly.

2-50

The Instrument Panel -Your Information System

2-51

The main components of your instrument panel are:

A. Fog Lamp Switch

B. Instrument Panel Intensity Control

C. Turn Signal/Multifunction Lever

D. Horn

E. Instrument Cluster

F. Windshield Wiper/Washer Lever

G. Ignition Switch

H. Enhanced Traction System

I. Hazard Switch

J. Audio System

K. Climate Control System

L. Cigarette Lighter

M. Gear Shift Lever

N. Cruise Control Switches (If Equipped)

O. Steering Wheel Audio System (If Equipped)

P. Tilt Wheel Lever

Q. Hood Release Handle

R. Fuse Panel

2-52

Instrument Panel ClusterYour vehicle is equipped with this cluster or one very similar to it. It includes indicator warning lights and gages thatare explained on the following pages. Be sure to read about them.

Automatic Transaxle Cluster Shown, Manual Transaxle Cluster and Canada Cluster Similar

2-53

Speedometer and OdometerYour speedometer lets you see your speed in both milesper hour (mph) and kilometers per hour (km/h).

Your odometer shows how far your vehicle has beendriven, in either miles (used in the United States) orkilometers (used in Canada).

Your vehicle has a tamper resistant odometer. Thedigital odometer will read 999,999 if someone tries toturn it back.

You may wonder what happens if your vehicle needs anew odometer installed. If the new one can be set to themileage total of the old odometer, then it must be. But ifit can’t, then it’s set at zero and a label must be put onthe driver’s door to show the old mileage reading whenthe new odometer was installed.

Trip Odometer

The trip odometer can tell you how far you have drivensince you last reset it.

The reset button is located next to the trip odometer. Toreset the trip odometer to zero, press and hold the resetbutton for one to two seconds while the trip odometer isdisplayed. Also by pressing this button, for less than onesecond you can toggle between the odometer and thetrip odometer.

Tachometer

The tachometer shows your engine speed in revolutionsper minute (rpm).

NOTICE:

Do not run your engine at speeds in the red area,or engine damage may occur.

2-54

Warning Lights, Gages and IndicatorsThis part describes the warning lights and gages thatmay be on your vehicle. The pictures will help youlocate them.

Warning lights and gages can signal that something iswrong before it becomes serious enough to cause anexpensive repair or replacement. Paying attention toyour warning lights and gages could also save you orothers from injury.

Warning lights come on when there may be or is aproblem with one of your vehicle’s functions. As youwill see in the details on the next few pages, somewarning lights come on briefly when you start theengine just to let you know they’re working. If you arefamiliar with this section, you should not be alarmedwhen this happens.

Gages can indicate when there may be or is a problemwith one of your vehicle’s functions. Often gages andwarning lights work together to let you know whenthere’s a problem with your vehicle.

When one of the warning lights comes on and stays onwhen you are driving, or when one of the gages showsthere may be a problem, check the section that tells youwhat to do about it. Please follow this manual’s advice.Waiting to do repairs can be costly -- and evendangerous. So please get to know your warning lightsand gages. They’re a big help.

Safety Belt Reminder LightWhen the key is turned to ON or START a chime willcome on for about eight seconds to remind people tofasten their safety belts, unless the driver’s safety belt isalready buckled.

The safety belt light willalso come on and stay onfor about 20 seconds, then it will flash for about 55 seconds.

If the driver’s belt is already buckled, neither the chimenor the light will come on.

2-55

Air Bag Readiness LightThere is an air bag readiness light on the instrumentpanel, which shows AIR BAG. The system checks theair bag’s electrical system for malfunctions. The lighttells you if there is an electrical problem. The systemcheck includes the air bag modules, the wiring and thecrash sensing and diagnostic module. For moreinformation on the air bag system, see “Air Bag” in the Index.

This light will come onwhen you start your vehicle,and it will flash for a fewseconds. Then the lightshould go out. This meansthe system is ready.

If the air bag readiness light stays on after you start thevehicle or comes on when you are driving, your air bagsystem may not work properly. Have your vehicleserviced right away.

CAUTION:

If the air bag readiness light stays on after youstart your vehicle, it means the air bag systemmay not be working properly. The air bags inyour vehicle may not inflate in a crash, or theycould even inflate without a crash. To help avoidinjury to yourself or others, have your vehicleserviced right away if the air bag readiness lightstays on after you start your vehicle.

The air bag readiness light should flash for a fewseconds when you turn the ignition key to ON. If thelight doesn’t come on then, have it fixed so it will beready to warn you if there is a problem.

2-56

Charging System Indicator Light

The charging systemindicator light will come on when you turn on theignition, but the engine isnot running, as a check toshow you it is working.

When the engine is running, the light should go out.

If it stays on, or comes on while you are driving and you hear a chime, you may have a problem with theelectrical charging system. It could indicate that youhave a loose generator drive belt or another electricalproblem. Have it checked right away. Driving while thislight is on could drain your battery.

If you must drive a short distance with the light on, becertain to turn off all your accessories, such as the radioand air conditioner.

Up-Shift Light (Manual Transaxle)

This light comes on whenyou need to shift to the nexthigher gear. See “ManualTransaxle” in the Index.

Brake System Warning LightYour vehicle’s hydraulic brake system is divided intotwo parts. If one part isn’t working, the other part canstill work and stop you. For good braking, though, youneed both parts working well.

If the warning light comes on, there is a brake problem.Have your brake system inspected right away.

United States Canada

2-57

This light should come on briefly when you turn theignition key to ON. If it doesn’t come on then, have itfixed so it will be ready to warn you if there’s a problem.

If the light comes on while you are driving, pull off theroad and stop carefully. You may notice that the pedal isharder to push. Or, the pedal may go closer to the floor.It may take longer to stop. If the light is still on, have thevehicle towed for service. (See “Towing Your Vehicle”in the Index.)

CAUTION:

Your brake system may not be working properlyif the brake system warning light is on. Drivingwith the brake system warning light on can leadto an accident. If the light is still on after you’vepulled off the road and stopped carefully, havethe vehicle towed for service.

When the ignition is on, the brake system warning lightwill also come on when you set your parking brake. Thelight will stay on if your parking brake doesn’t releasefully. If it stays on after your parking brake is fullyreleased, it means you have a brake problem.

Anti-Lock Brake System Warning Light

With the anti-lock brakesystem, this light will comeon when you start yourengine and it will stay on for three seconds. That’s normal.

If the light stays on, turn the ignition to OFF. Or, if thelight comes on when you’re driving, stop as soon aspossible and turn the ignition off. Then start the engineagain to reset the system. If the light still stays on, orcomes on again while you’re driving, your vehicle needsservice. If the regular brake system warning light isn’ton, you still have brakes, but you don’t have anti-lockbrakes. If the regular brake system warning light is alsoon, you don’t have anti-lock brakes and there’s aproblem with your regular brakes. See “Brake SystemWarning Light” earlier in this section.

The anti-lock brake system warning light should comeon briefly when you turn the ignition key to ON. If thelight doesn’t come on then, have it fixed so it will beready to warn you if there is a problem.

2-58

Enhanced Traction System Warning Light

With the Enhanced TractionSystem (ETS), this warninglight should come on brieflyas you start the engine. Ifthe warning light doesn’tcome on then, have it fixedso it will be ready to warnyou if there’s a problem.

If the warning light stays on, or comes on when you’redriving, there may be a problem with your EnhancedTraction System and your vehicle may need service.When this warning light is on, the system will not limitwheel spin. Adjust your driving accordingly.

The Enhanced Traction System warning light may comeon for the following reasons:

� If you turn the system off by pressing the ETS buttonlocated on the instrument panel above the audiosystem, the warning light will come on and stay on.To turn the system back on, press the button again.The warning light should go off. (See “EnhancedTraction System” in the Index for more information.)

� The warning light will come on when you set yourparking brake with the engine running, and it willstay on if your parking brake doesn’t release fully. If the system is turned on and the warning light stayson after your parking brake is fully released, itmeans there’s a problem with the system.

� If the traction control system is affected by anengine-related problem, the system will turn off andthe warning light will come on.

If the Enhanced Traction System warning light comeson and stays on for an extended period of time when thesystem is turned on and the parking brake is fullyreleased, your vehicle needs service.

2-59

Enhanced Traction System Active Light

When your EnhancedTraction System is limiting wheel spin, this light will come on.Slippery road conditionsmay exist if the EnhancedTraction System active lightcomes on, so adjust yourdriving accordingly.

The light will stay on for a few seconds after theEnhanced Traction System stops limiting wheel spin.

This light will also come on when the anti-lock brakesystem is active.

The Enhanced Traction System active light also comeson briefly when you turn the ignition key to ON. If thelight doesn’t come on then, have it fixed so it will bethere to tell you when the system is active.

Engine Coolant Temperature Gage

United States Canada

This gage shows the engine coolant temperature. If thegage pointer moves into the red area, the light comes onand you hear a chime, your engine is too hot! It meansthat your engine coolant has overheated.

The “Problems on the Road” section of this manualshows what to do. See “Engine Overheating” in the Index.

2-60

Low Coolant Warning Light

This light comes on briefly when you turn yourignition on.

If this light comes on and stays on and you hear a chime,the vehicle should promptly be pulled off the road andthe coolant level checked.

See “Engine Coolant” in the Index. If there are visiblesigns of steam, see “Engine Overheating” in the Indexbefore opening the hood. Have your vehicle serviced assoon as you can.

Malfunction Indicator Lamp (Service Engine Soon Light)

Your vehicle is equippedwith a computer whichmonitors operation of thefuel, ignition and emissioncontrol systems.

This system is called OBD II (On-BoardDiagnostics-Second Generation) and is intended toassure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleanerenvironment. The SERVICE ENGINE SOON lightcomes on to indicate that there is a problem and serviceis required. Malfunctions often will be indicated by thesystem before any problem is apparent. This mayprevent more serious damage to your vehicle. Thissystem is also designed to assist your service technicianin correctly diagnosing any malfunction.

2-61

NOTICE:

If you keep driving your vehicle with this lighton, after a while, your emission controls may notwork as well, your fuel economy may not be asgood and your engine may not run as smoothly.This could lead to costly repairs that may not becovered by your warranty.

NOTICE:

Modifications made to the engine, transaxle,exhaust or fuel system of your vehicle or thereplacement of the original tires with other thanthose of the same Tire Performance Criteria(TPC) can affect your vehicle’s emission controlsand may cause the SERVICE ENGINE SOONlight to come on. Modifications to these systemscould lead to costly repairs not covered by yourwarranty. This may also result in a failure to passa required Emission Inspection/Maintenance test.

This light should come on, as a check to show you it isworking, when the ignition is on and the engine is notrunning. If the light doesn’t come on, have it repaired.This light will also come on during a malfunction in oneof two ways:

� Light Flashing -- A misfire condition has beendetected. A misfire increases vehicle emissions andmay damage the emission control system on yourvehicle. Dealer or qualified service center diagnosisand service may be required.

� Light On Steady -- An emission control systemmalfunction has been detected on your vehicle.Dealer or qualified service center diagnosis andservice may be required.

If the Light Is Flashing

The following may prevent more serious damage toyour vehicle:

� Reducing vehicle speed.

� Avoiding hard accelerations.

� Avoiding steep uphill grades.

� If you are towing a trailer, reduce the amount ofcargo being hauled as soon as it is possible.

2-62

If the light stops flashing and remains on steady, see “If the Light Is On Steady” following.

If the light continues to flash, when it is safe to do so,stop the vehicle. Find a safe place to park your vehicle.Turn the key off, wait at least 10 seconds and restart theengine. If the light remains on steady, see “If the LightIs On Steady” following. If the light is still flashing,follow the previous steps, and drive the vehicle to yourdealer or qualified service center for service.

If the Light Is On Steady

You may be able to correct the emission systemmalfunction by considering the following:

Did you recently put fuel into your vehicle?

If so, reinstall the fuel cap, making sure to fully installthe cap. See “Filling Your Tank” in the Index. Thediagnostic system can determine if the fuel cap has beenleft off or improperly installed. A loose or missing fuelcap will allow fuel to evaporate into the atmosphere. A few driving trips with the cap properly installedshould turn the light off.

Did you just drive through a deep puddle of water?

If so, your electrical system may be wet. The conditionwill usually be corrected when the electrical systemdries out. A few driving trips should turn the light off.

Have you recently changed brands of fuel?

If so, be sure to fuel your vehicle with quality fuel (see “Fuel” in the Index). Poor fuel quality will causeyour engine not to run as efficiently as designed. Youmay notice this as stalling after start-up, stalling whenyou put the vehicle into gear, misfiring, hesitation on acceleration or stumbling on acceleration. (These conditions may go away once the engine iswarmed up.) This will be detected by the system andcause the light to turn on.

If you experience one or more of these conditions,change the fuel brand you use. It will require at least onefull tank of the proper fuel to turn the light off.

If none of the above steps have made the light turn off,have your dealer or qualified service center check thevehicle. Your dealer has the proper test equipment anddiagnostic tools to fix any mechanical or electricalproblems that may have developed.

Emissions Inspection and Maintenance Programs

Some state/provincial and local governments have ormay begin programs to inspect the emission controlequipment on your vehicle. Failure to pass thisinspection could prevent you from getting a vehicle registration.

2-63

Here are some things you need to know in order to helpyour vehicle pass an inspection:

Your vehicle will not pass this inspection if theSERVICE ENGINE SOON light is on or not working properly.

Your vehicle will not pass this inspection if the OBD(on-board diagnostic) system determines that criticalemission control systems have not been completelydiagnosed by the system. The vehicle would beconsidered not ready for inspection. This can happen if you have recently replaced your battery or if yourbattery has run down. The diagnostic system is designed to evaluate critical emission control systemsduring normal driving. This may take several days ofroutine driving. If you have done this and your vehiclestill does not pass the inspection for lack of OBD systemreadiness, see your dealer or qualified service center toprepare the vehicle for inspection.

Oil Pressure Light

If you have a low engine oilpressure problem, this lightwill stay on after you startyour engine, or come onand you will hear a chimewhen you are driving.

This indicates that your engine is not receiving enoughoil. The engine could be low on oil, or could have someother oil problem. Have it fixed immediately.

When the ignition is on but the engine is not running,the light will come on as a test to show you it isworking, but the light will go out when the engine isrunning. If it doesn’t come on with the ignition on, you may have a problem with the fuse or bulb. Have itfixed right away.

2-64

CAUTION:

Don’t keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches fire. You or others could be burned.Check your oil as soon as possible and have yourvehicle serviced.

NOTICE:

Damage to your engine from neglected oilproblems can be costly and is not covered by your warranty.

Low Oil Light (If Equipped)If your vehicle is equippedwith a 3400 V6 engine, thenyou will have a LOW OILlight on your instrumentpanel cluster.

This light will come on briefly when you start your vehicle.

If the light stays on after starting your vehicle, or comeson and chimes while you are driving, your engine oillevel should be checked.

Prior to checking the oil level, be sure your vehicle hasbeen shut off for several minutes and is on a levelsurface. Check the oil level on your dipstick and bring itto the proper level. See “Engine Oil” in the Index.

A false LOW OIL light may be generated when parkingon steep grades.

The oil level monitoring system only checks oil levelduring the brief period between when the key is on andthe engine is cranking. It does not monitor engine oillevel when the engine is running. Additionally, an oillevel check is only performed if the engine has beenturned off for a considerable period of time allowing theoil normally in circulation to drain back into the oil pan.

2-65

Change Oil Light

The CHANGE OIL lightshould come on briefly as abulb check when you startthe engine. If the lightdoesn’t come on, have it serviced.

If the CHANGE OIL light comes on and stays on afteryou start the engine, have the oil changed.

For additional information, see “Engine Oil, When toChange” in the Index. To reset the Oil Life Monitor, see“Engine Oil Life Monitor” in the Index.

Security Light

This light will come onwhen you turn the key toON and will stay on untilthe vehicle starts.

If you’re driving and the security light comes on andremains on, your Passlock� system is not workingproperly. Your vehicle is not protected by Passlock andyou should see your dealer.

2-66

Cruise Light (If Equipped)

The CRUISE light comeson whenever you set yourcruise control.

Low Washer Light

This light will come onbriefly when you turn on the ignition.

It will also stay on, or come on and a chime will sound,if the windshield washer fluid reservoir is less thanone-third full.

Service Vehicle Soon Light

This light will come onbriefly when you turn on the ignition.

It will stay on, or come on and a chime will sound if itdetects a problem on the vehicle, such as a DRL or anALC malfunction. If this happens, see your dealer assoon as possible.

2-67

Fuel Gage

United States Canada

Your fuel gage tells you about how much fuel you haveleft, when the ignition is on. When the indicator nearsempty, the light will come on and you will hear a chime.You still have a little fuel left, but you should get more soon.

Here are four things that some owners ask about. None of these show a problem with your fuel gage:

� At the service station, the gas pump shuts off beforethe gage reads full.

� It takes a little more or less fuel to fill up than thegage indicated. For example, the gage may haveindicated the tank was half full, but it actually took alittle more or less than half the tank’s capacity to fillthe tank.

� The gage moves a little when you turn a corner orspeed up.

� The gage goes back to empty when you turn off the ignition.

3-3-1

Section 3 Comfort Controls and Audio Systems

In this section, you’ll find out how to operate the comfort control and audio systems offered with your vehicle. Be sure to read about the particular systems supplied with your vehicle.

3-2 Comfort Controls3-2 Climate Control System with Air Conditioning3-3 Air Conditioning3-4 Heating3-4 Defogging and Defrosting Windows3-5 Rear Window Defogger3-5 Ventilation System3-6 Audio Systems3-6 Setting the Clock for All Systems Except

AM-FM Stereo3-7 AM-FM Stereo with Cassette Tape Player

3-10 AM-FM Stereo with Compact Disc Player and Equalizer (If Equipped)

3-13 Remote Cassette Tape Player (If Equipped)3-14 Theft-Deterrent Feature (If Equipped)3-17 Audio Steering Wheel Controls (If Equipped)3-18 Understanding Radio Reception3-18 Tips About Your Audio System3-19 Care of Your Cassette Tape Player3-20 Care of Your Compact Discs3-20 Care of Your Compact Disc Player3-20 Fixed Mast Antenna

3-2

Comfort ControlsWith this system, you can control the ventilation andheating in your vehicle.

Your vehicle also has the flow-through ventilationsystem described later in this section.

Climate Control System with Air Conditioning

Fan KnobThe left control knob sets the fan speed. To select theforce of air you want, turn the knob. The fan is alwaysrunning unless the fan knob is moved to OFF.

Temperature KnobThe center control knob regulates the temperature of the air coming through the system.

Mode Knob

The right control knob changes the functions of your system.

MAX: Use for maximum cooling. This settingrecirculates much of the air inside your vehicle. Itmaximizes your air conditioner’s performance and yourvehicle’s fuel economy. The air conditioning compressorwill run automatically in this position when it is neededto help dry the air in the vehicle.

VENT: In this position most of the airflow comesthrough the instrument panel outlets. A small amount ofair comes through the floor vents. Set the center controlknob to the temperature desired.

BI-LEVEL: In this position the airflow comesthrough the instrument panel outlets and through thefloor outlets. Set the center control knob to thetemperature desired.

3-3

FLOOR: In this position most of the airflowcomes through the floor outlet. The rest of the air comesthrough the windshield and side window vents. Set thecenter control knob to the temperature desired.

DEFOG: This position divides the airflowbetween the floor outlets and the windshield defrostervent. The air conditioning compressor will runautomatically in this position when it is needed to help dry the air in the vehicle.

FRONT DEFROSTER: This position directsmost of the airflow through the window defroster vent.Some of the air goes to the floor outlets. The airconditioning compressor will run automatically in this position when it is needed to help dry the air in the vehicle.

Air Conditioning Compressor Button

Press A/C to operate the air conditioner compressor. The indicator light will glow when the button is pressedto indicate that the air conditioning system has beenturned on. The fan knob must be set to a speed for the air conditioning to operate.

Air ConditioningThe air conditioner and heater work best if you keepyour windows closed while using them. Your vehiclealso has the flow-through ventilation system describedlater in this section.

On very hot days, open the windows long enough to let hot inside air escape. This reduces the time it takesfor your vehicle to cool down, which should help fuel economy.

On cool, but sunny days, the sun may warm your upper body, but your lower body may not be warmenough. You can use BI-LEVEL with the temperatureknob in the middle and the A/C indicator light glowing. The system will bring in outside air and direct slightlywarmer air to your lower body.

For normal cooling on hot days, use VENT with thetemperature knob in the blue area and the A/C indicatorlight glowing. The system will bring in outside air andcool it.

3-4

HeatingOn cold days, use FLOOR with the temperature knob all the way in the red area. The system will bring inoutside air, heat it and send it to the floor outlets.

Your vehicle has heat ducts that are directed toward therear seat. Keep the area under the front seats clear ofobstructions so that the heated air can reach the rear seat passengers.

If your vehicle has an engine coolant heater, you can use it to help your system provide warm air faster whenit’s cold outside (0�F (-18�C) or lower). An enginecoolant heater warms the coolant your engine andheating system use to provide heat. See “Engine Coolant Heater” in the Index.

Defogging and Defrosting WindowsYour system has two settings for clearing the front andside windows. For each setting, adjust the temperaturecontrol as desired.

To defrost the front window quickly, turn the temperaturecontrol knob all the way in the red area. Use FRONTDEFROST and adjust the fan to the highest speed. To warm passengers while keeping the front windowclean, use DEFOG.

Your vehicle is equipped with side window defoggervents. The side window defogger vents are located on theoutside of the side instrument panel vents. To defrost theside windows, turn the temperature control knob all theway in the red area. Use FLOOR and adjust the fan to the highest speed. To control fogging of the windows,turn the temperature control knob all the way in the redarea. Use DEFOG and adjust the fan to the highest speed.

To defog the side windows while using air conditioning,use BI-LEVEL and adjust the fan to the highest speedand press the A/C button so that the indicator light isglowing. For added airflow to the side windows aim theside vents toward the windows and close the center vents.

3-5

Rear Window Defogger

The rear window defoggeruses a warming grid toremove fog from the rear window.

Press the defogger button. The indicator light will glow.The rear window defogger will turn itself off after aboutten minutes after the first time the button is pressed, and after five minutes each additional time the button ispressed. You can turn the defogger off by pressing thebutton again or turning off the ignition.

Do not attach a temporary vehicle license across thedefogger grid on the rear window.

NOTICE:

Don’t use a razor blade or anything else sharp on the inside of the rear window. If you do, youcould cut or damage the warming grid, and therepairs wouldn’t be covered by your warranty.

Ventilation SystemFor mild outside temperatures when little heating orcooling is needed, use VENT to direct outside airthrough your vehicle. Your vehicle also has theflow-through ventilation system.

Your vehicle’s flow-through ventilation system suppliesoutside air into the vehicle when it is moving. Outsideair will also enter the vehicle when the air conditioningfan is running.

3-6

Ventilation Tips

� Keep the hood and front air inlet free of ice, snow orany other obstruction, such as leaves. The heater anddefroster will work far better, reducing the chance offogging the inside of your windows.

� When you enter a vehicle in cold weather, adjust themode knob to FLOOR and the fan to the highestspeed for a few moments before driving off. Thishelps clear the intake ducts of snow and moistureand reduces the chance of fogging the inside of your windows.

� Keep the air path under the front seats clear of objects. This helps air circulate throughout your vehicle.

Audio SystemsYour audio system has been designed to operate easilyand give years of listening pleasure. You will get themost enjoyment out of it if you acquaint yourself with itfirst. Find out what your audio system can do and howto operate all its controls, to be sure you’re getting themost out of the advanced engineering that went into it.

Setting the Clock for All Systems Except AM-FM StereoPress and hold HR until the correct hour appears. Press and hold MIN until the correct minute appears.There will be a two-second delay before the clock goesinto time-set mode, and the colon on the display willblink while in this mode.

3-7

AM-FM Stereo with Cassette Tape Player

Playing the Radio

POWER-VOL: Push this knob to turn the system on and off. To increase volume, turn the knob clockwise.Turn it counterclockwise to decrease volume.

RECALL: Display the time with the ignition off bypressing this button. When the radio is playing, pressthis knob to recall the station frequency.

Finding a Station

AM -FM: Press this button to switch between AM, FM1 and FM2. The display shows your selection.

TUNE: Press this knob lightly so it extends. Turn it tochoose radio stations. Push the knob back into its storedposition when you’re not using it.

SEEK: Press the up or down arrow to go to the nexthigher or lower station and stay there.

PUSHBUTTONS: The six numbered pushbuttons letyou return to your favorite stations. You can set up to 18 stations (six AM, six FM1 and six FM2). Just:

1. Turn the radio on.

2. Press AM-FM to select the band.

3. Tune in the desired station.

4. Press and hold one of the six numbered buttons untilSET appears on the display. Whenever you press thatnumbered button, the station you set will return.

5. Repeat the steps for each pushbutton.

3-8

Setting the Tone

BASS: Slide the lever to the right or left to increase ordecrease bass.

TREBLE: Slide the lever to the right or left to increaseor decrease treble. If a station is weak or noisy, you maywant to decrease the treble.

Adjusting the Speakers

BAL: Press this knob lightly so it extends. Turn thisknob to move the sound to the left or right speakers. The middle position balances the sound between the speakers.

FADE: Press this knob lightly so it extends. Turn thisknob to move the sound to the front or rear speakers.The middle position balances the sound between the speakers.

Push these knobs back into their stored positions whenyou’re not using them.

Playing a Cassette Tape

Your tape player is built to work best with tapes that are up to 30 to 45 minutes long on each side. Tapeslonger than that are so thin they may not work well in this player.

While the tape is playing, use the VOL, FADE, BAL,BASS and TREB controls just as you do for the radio.The display will show an arrow to show which side ofthe tape is playing. When the down indicator arrow islit, selections listed on the bottom side of the cassette are playing. When the up arrow is lit, selections listed onthe top side of the cassette are playing. The tape playerautomatically begins playing the other side when itreaches the end of the tape.

If E and a number appear on the radio display, the tapewon’t play because of an error.

� E10: The tape is tight and the player can’t turn the tape hubs. Remove the tape. Hold the tape withthe open end down and try to turn the right hubcounterclockwise with a pencil. Turn the tape overand repeat. If the hubs do not turn easily, your tapemay be damaged and should not be used in theplayer. Try a new tape to make sure your player is working properly.

� E11: The tape is broken. Try a new tape.

If any error occurs repeatedly or if an error can’t becorrected, please contact your dealer. If your radiodisplays an error number, write it down and provide it to your dealer when reporting the problem.

3-9

PREV (1): Press this button or the SEEK down arrow to search for the previous selection on the tape. Yourtape must have at least three seconds of silence betweeneach selection for PREV or SEEK to work. The tapedirection arrow blinks during PREV or SEEK operation.Press PREV or the SEEK down arrow to stop searching.The sound will mute during PREV or SEEK operation.

NEXT (2): Press this button or the SEEK up arrow tosearch for the next selection on the tape. If you hold thebutton, the player will continue moving forward throughthe tape. Your tape must have at least three seconds ofsilence between each selection for NEXT or SEEK towork. The tape direction arrow blinks during NEXT orSEEK operation. Press NEXT or the SEEK up arrow to stop searching. The sound will mute during NEXT or SEEK operation.

PROG (3): Press this button to play the other side of the tape.

� (4): Press this button to reduce background noise. Note that the double-D symbol will appear on the display.

Dolby Noise Reduction is manufactured under a licensefrom Dolby Laboratories Licensing Corporation. Dolbyand the double-D symbol are trademarks of DolbyLaboratories Licensing Corporation.

REV (5): Press this button to reverse the tape rapidly.Press it again to return to playing speed. The radio willplay the last selected station while the tape reverses. You may select stations during REV operation by using SEEK or TUNE.

FWD (6): Press this button to advance quickly toanother part of the tape. Press the button again to returnto playing speed. The radio will play the last selectedstation while the tape advances. You may select stationsduring FWD operation by using SEEK or TUNE.

AM -FM: Press this button to play the radio when a tape is in the player.

TAPE/PLAY: Press this button to change to the tape function when the radio is on. The tape symbolwith an arrow will appear on the display when the tapeis active. To return to playing the radio, press theAM-FM button.

EJECT: Press this button to remove the tape. The radio will play. EJECT may be activated with either theignition or radio off. Cassettes may be loaded with the radio and ignition off if this button is pressed first.

3-10

CLN: If this message appears on the display, the cassettetape player needs to be cleaned. It will still play tapes, butyou should clean it as soon as possible to prevent damageto the tapes and player. See “Care of Your Cassette TapePlayer” in the Index. After you clean the player, press andhold EJECT for five seconds to reset the CLN indicator.The radio will display --- to show the indicator was reset.

CD Adapter Kits

It is possible to use a portable CD player adapter kitwith your cassette tape player after activating the bypassfeature on your tape player.

To activate the bypass feature, use the following steps:

1. Turn the ignition to ON or ACC.

2. Turn the radio off.

3. Press and hold the TAPE/PLAY button for threeseconds. The tape symbol on the display will flashfor two seconds, indicating the feature is active.

4. Insert the adapter into the cassette slot. It will power up the radio and begin playing.

This override routine will remain active until EJECT is pressed.

AM-FM Stereo with Compact Disc Playerand Equalizer (If Equipped)

Playing the Radio

POWER-VOL: Push this knob to turn the system on and off. To increase volume, turn the knob clockwise.Turn it counterclockwise to decrease volume.

RECALL: Press this button briefly to recall the stationbeing played or to display the clock. If you press theknob when the ignition is off, the clock will show for a few seconds.

3-11

Finding a Station

AM/FM: Press this button to switch between AM, FM1 and FM2. The display shows your selection.

TUNE: Press this knob lightly so it extends. Turn it tochoose radio stations. Push the knob back into its storedposition when you’re not using it.

SEEK: Press the up or down arrow to go to the nexthigher or lower station and stay there.

PUSHBUTTONS: The six numbered pushbuttons letyou return to your favorite stations. You can set up to 18 stations (six AM, six FM1 and six FM2). Just:

1. Turn the radio on.

2. Press AM-FM to select the band.

3. Tune in the desired station.

4. Press and hold one of the six numbered buttons untilSET appears on the display. Whenever you press thatnumbered button, the station you set will return.

5. Repeat the steps for each pushbutton.

Setting the Tone

EQUALIZER: A seven-band equalizer is part of youraudio system. Slide the levers up to boost or down toreduce frequency range.

Adjusting the Speakers

BAL: Press this knob lightly so it extends. Turn it tomove the sound to the left or right speakers. The middleposition balances the sound between the speakers.

FADE: Press this knob lightly so it extends. Turn it tomove the sound to the front or rear speakers. The middleposition balances the sound between the speakers.

Push these knobs back into their stored positions whenyou’re not using them.

Playing a Compact Disc

Insert a disc partway into the slot, label side up. Theplayer will pull it in. If the ignition and the radio are on,the disc will begin playing. If you want to insert a discwhen the ignition is off, first press EJECT.

3-12

If you’re driving on a very rough road or if it’s very hot,the disc may not play and E (error) and a number mayappear on the radio display. If the disc comes out, it could be that:

� The disc is upside down.

� It is dirty, scratched or wet.

� The air is very humid. (If so, wait about an hour and try again.)

If any error occurs repeatedly or if an error can’t becorrected, please contact your dealer. If your radiodisplays an error number, write it down and provide it to your dealer when reporting the problem.

PREV (1): Press this button or the SEEK down arrow to go to the start of the current track if more than eightseconds have played. If you hold the button or press itmore than once, the player will continue moving backthrough the disc.

NEXT (2): Press this button or the SEEK up arrow togo to the start of the next track. If you hold the button or press it more than once, the player will continuemoving forward through the disc.

RDM (3): Press this button to hear the tracks in random,rather than sequential, order. The display will showRDM. Press RDM again to turn off random play.

REV (5): Press and hold this button to quickly reversewithin a track. Release it to play the passage. You willhear sound at a reduced volume. The display will showelapsed time.

FWD (6): Press and hold this button to quickly advancewithin a track. You will hear sound at a reduced volume.The display will show elapsed time.

RECALL: Press this button to see what track iscurrently playing. Press RECALL again within fiveseconds to see how long the track has been playing.When a new track starts to play, the track number willalso appear. Press RECALL a third time and the time of day will be displayed.

AM/FM: Press this button to play the radio when a discis playing. The disc will stop but remain in the player.

CD/PLAY: Press this button to change to the discfunction when the radio is on.

EJECT: Press this button to remove the disc or stop the disc and switch to the radio. EJECT will work withthe radio off.

3-13

Remote Cassette Tape Player (If Equipped)

Playing a Cassette Tape

With this option, the remote single cassette player ismounted to the console.

Your tape player is built to work best with tapes that are up to 30 to 45 minutes long on each side. Tapeslonger than that are so thin they may not work well in this player.

With the radio on, insert a cassette tape. Once the tape is playing, use the control knobs for VOL, BAL, FADE,BASS and TREB just as you do for the radio. A lightedcassette symbol shows when a cassette tape is in theplayer. A lighted arrow will also appear and show thedirection of play when a tape is active.

PREV (1): Press PREV or the SEEK down arrow to search for the previous selection. A minimumthree-second blank gap is needed for the player to stop at the beginning of the selection. The tape direction arrow will blink during the SEEK operationand the sound will mute in this mode.

NEXT (2): Press NEXT or the SEEK up arrow tosearch for the next selection. The tape direction arrowwill blink during the SEEK operation and the sound will mute in this mode.

(4): Press this button to reduce background tape noise(noise reduction is only available in the cassette mode).The double-D symbol will appear on the display.

REV (5): Press this button to rapidly reverse the tape.The tape will rapidly reverse to the beginning of thecassette reel or until you press REV again. Use theSEEK button or the TUNE knob to play the radio during REV. The radio plays the last selected station.

FWD (6): Press this button to rapidly advance the tape.The tape will rapidly advance to the end of the cassettereel or until you press FWD again. Use the SEEK button or the TUNE knob to play the radio during FWD.The radio plays the last selected station.

3-14

PROG: Press this button on the remote cassette playerto go from one side of the tape to the other.

CD/PLAY: After a cassette tape and a CD have beeninserted, press the CD/PLAY button to switch betweenthe CD player and the cassette tape player. Both featurescannot be played at the same time.

EJECT: Press this button on the remote cassette playerto remove the tape. EJECT can be used with either theignition or radio off. Also, you must press EJECT beforeloading a cassette with the radio off to allow loading.

CLN: If this message appears on the display, thecassette tape player needs to be cleaned. It will still playtapes, but you should clean it as soon as possible toprevent damage to the tapes and player. See “Care ofYour Cassette Tape Player” in the Index. After you cleanthe player, press and hold RECALL on the radio and theEJECT button on the remote cassette at the same timefor five seconds to reset the CLN indicator. The radiowill display --- to show the indicator was reset.

Theft-Deterrent Feature (If Equipped)THEFTLOCK� is designed to discourage theft of yourradio. It works by using a secret code to disable all radiofunctions whenever battery power is removed.

The THEFTLOCK feature for the radio may be used orignored. If ignored, the system plays normally and theradio is not protected by the feature. If THEFTLOCK is activated, your radio will not operate if stolen.

When THEFTLOCK is activated, the radio will displayLOC to indicate a locked condition anytime batterypower is removed. If your battery loses power for anyreason, you must unlock the radio with the secret codebefore it will operate.

3-15

Activating the Theft-Deterrent Feature

The instructions which follow explain how to enter your secret code to activate the THEFTLOCK system. It is recommended that you read through all nine stepsbefore starting the procedure.

If you allow more than 15 seconds to elapse betweenany steps, the radio automatically reverts to time andyou must start the procedure over at Step 4.

1. Write down any three or four-digit number from 000 to 1999 and keep it in a safe place separate fromthe vehicle.

2. Turn the ignition to ACC or ON.

3. Turn the radio off.

4. Press the 1 and 4 buttons together. Hold them downuntil --- shows on the display. Next you will use thesecret code number which you have written down.

5. Press MIN and 000 will appear on the display.

6. Press MIN again to make the last two digits agreewith your code.

7. Press HR to make the first one or two digits agreewith your code.

8. Press AM-FM after you have confirmed that thecode matches the secret code you have written down.The display will show REP to let you know that youneed to repeat Steps 5 through 7 to confirm yoursecret code.

9. Press AM-FM and this time the display will showSEC to let you know that your radio is secure.

Note that with the ignition off, the THEFTLOCK LEDindicator will flash, indicating a secured radio.

3-16

Unlocking the Theft-Deterrent Feature After a Power Loss

Enter your secret code as follows; pause no more than15 seconds between steps:

1. Turn the ignition on. LOC will appear on the display.

2. Press MIN and 000 will appear on the display.3. Press MIN again to make the last two digits agree

with your code.

4. Press HR to make the first one or two digits agreewith your code.

5. Press AM-FM after you have confirmed that thecode matches the secret code you have written down.The display will show SEC, indicating the radio isnow operable and secure.

If you enter the wrong code eight times, INOP willappear on the display. You will have to wait an hourwith the ignition on before you can try again. When you try again, you will only have three more chances(eight tries per chance) to enter the correct code beforeINOP appears.

If you lose or forget your code, contact your dealer.

Disabling the Theft-Deterrent Feature

Enter your secret code as follows; pause no more than15 seconds between steps:

1. Turn the ignition to ACC or ON.2. Turn the radio off.3. Press the 1 and 4 buttons together. Hold them down

until SEC shows on the display.4. Press MIN and 000 will appear on the display.5. Press MIN again to make the last two digits agree

with your code.6. Press HR to make the first one or two digits agree

with your code.7. Press AM-FM after you have confirmed that the

code matches the secret code you have written down.The display will show ---, indicating that the radio is no longer secured.

If the code entered is incorrect, SEC will appear on thedisplay. The radio will remain secured until the correctcode is entered.When battery power is removed and later applied to asecured radio, the radio won’t turn on and LOC willappear on the display.

To unlock a secured radio, see “Unlocking theTheft-Deterrent Feature After a Power Loss” earlier in this section.

3-17

Audio Steering Wheel Controls (If Equipped)

If your vehicle has this feature, you can control certainradio functions using the buttons on your steering wheel.

SEEK: Press the up arrow to tune to the next radiostation and the down arrow to tune to the previous radiostation. If a cassette tape or compact disc is playing, theplayer will advance with the up arrow and reverse withthe down arrow.

AM -FM: Press this button to choose AM, FM1 or FM2. If a cassette tape or compact disc is playing, it will stop and the radio will play.

PRESET: Press this button to play a station you haveprogrammed on the radio preset buttons. If a cassettetape is playing, press this button to play the other side of the tape. If a compact disc is playing, press thisbutton to hear the tracks in random, rather thansequential, order. Press this button again to turn offrandom play.

PLAY: Press this button to play a cassette tape orcompact disc when the radio is playing.

MUTE: Press this button to silence the system. Press it again, or any other radio button, to turn on the sound.

VOLUME: Press the up or down arrow to increase or decrease volume.

3-18

Understanding Radio Reception

AM

The range for most AM stations is greater than for FM,especially at night. The longer range, however, cancause stations to interfere with each other. AM can pickup noise from things like storms and power lines. Tryreducing the treble to reduce this noise if you ever get it.

FM Stereo

FM stereo will give you the best sound, but FM signalswill reach only about 10 to 40 miles (16 to 65 km). Tall buildings or hills can interfere with FM signals,causing the sound to come and go.

Tips About Your Audio SystemHearing damage from loud noise is almost undetectableuntil it is too late. Your hearing can adapt to highervolumes of sound. Sound that seems normal can be loud and harmful to your hearing. Take precautions byadjusting the volume control on your radio to a safesound level before your hearing adapts to it.

To help avoid hearing loss or damage:

� Adjust the volume control to the lowest setting.

� Increase volume slowly until you hear comfortablyand clearly.

NOTICE:

Before you add any sound equipment to yourvehicle -- like a tape player, CB radio, mobiletelephone or two-way radio -- be sure you can add what you want. If you can, it’s veryimportant to do it properly. Added soundequipment may interfere with the operation ofyour vehicle’s engine, Delphi Delco Electronicsradio or other systems, and even damage them.Your vehicle’s systems may interfere with theoperation of sound equipment that has beenadded improperly.So, before adding sound equipment, check withyour dealer and be sure to check Federal rulescovering mobile radio and telephone units.

3-19

Care of Your Cassette Tape PlayerA tape player that is not cleaned regularly can causereduced sound quality, ruined cassettes or a damagedmechanism. Cassette tapes should be stored in theircases away from contaminants, direct sunlight andextreme heat. If they aren’t, they may not operateproperly or may cause failure of the tape player.

Your tape player should be cleaned regularly after every50 hours of use. Your radio may display CLN to indicatethat you have used your tape player for 50 hours withoutresetting the tape clean timer. If this message appears on the display, your cassette tape player needs to becleaned. It will still play tapes, but you should clean it assoon as possible to prevent damage to your tapes andplayer. If you notice a reduction in sound quality, try aknown good cassette to see if it is the tape or the tapeplayer at fault. If this other cassette has no improvementin sound quality, clean the tape player.

The recommended cleaning method for your cassette tape player is the use of a scrubbing action,non-abrasive cleaning cassette with pads which scrubthe tape head as the hubs of the cleaner cassette turn.The recommended cleaning cassette is available throughyour dealership (GM Part No. 12344789).

When using a scrubbing action, non-abrasive cleaningcassette, it is normal for the cassette to eject becauseyour unit is equipped with a cut tape detection featureand a cleaning cassette may appear as a broken tape. To prevent the cleaning cassette from being ejected, use the following steps.

1. Turn the ignition to ON or ACC.

2. Turn the radio off.

3. Press and hold the TAPE/PLAY button for threeseconds. The tape symbol on the display will flashfor two seconds.

4. Insert the scrubbing action cleaning cassette.

5. Eject the cleaning cassette after the manufacturer’srecommended cleaning time.

When the cleaning cassette has been ejected, the cut tapedetection feature is active again.

You may also choose a non-scrubbing action, wet-typecleaner which uses a cassette with a fabric belt to cleanthe tape head. This type of cleaning cassette will noteject on its own. A non-scrubbing action cleaner maynot clean as thoroughly as the scrubbing type cleaner.The use of a non-scrubbing action, dry-type cleaningcassette is not recommended.

3-20

After you clean the player, press and hold EJECT forfive seconds to reset the CLN indicator. The radio willdisplay --- to show the indicator was reset.

Cassettes are subject to wear and the sound quality may degrade over time. Always make sure the cassettetape is in good condition before you have your tapeplayer serviced.

Care of Your Compact DiscsHandle discs carefully. Store them in their original casesor other protective cases and away from direct sunlightand dust. If the surface of a disc is soiled, dampen aclean, soft cloth in a mild, neutral detergent solution andclean it, wiping from the center to the edge.

Be sure never to touch the signal surface when handlingdiscs. Pick up discs by grasping the outer edges or theedge of the hole and the outer edge.

Care of Your Compact Disc PlayerThe use of CD lens cleaner discs is not advised, due tothe risk of contaminating the lens of the CD optics withlubricants internal to the CD mechanism.

Fixed Mast AntennaThe fixed mast antenna can withstand most car washeswithout being damaged. If the mast should ever becomeslightly bent, you can straighten it out by hand. If themast is badly bent, as it might be by vandals, you shouldreplace it.

Check every once in a while to be sure the mast is stilltightened to the fender.

4-4-1

Section 4 Your Driving and the Road

Here you’ll find information about driving on different kinds of roads and in varying weather conditions. We’ve alsoincluded many other useful tips on driving.

4-2 Defensive Driving4-3 Drunken Driving4-6 Control of a Vehicle4-6 Braking4-9 Enhanced Traction System4-11 Steering4-13 Off-Road Recovery4-13 Passing4-15 Loss of Control4-16 Driving at Night4-17 Driving in Rain and on Wet Roads

4-20 City Driving4-21 Freeway Driving4-22 Before Leaving on a Long Trip4-23 Highway Hypnosis4-24 Hill and Mountain Roads4-25 Winter Driving4-29 Recreational Vehicle Towing4-32 Loading Your Vehicle4-34 Towing a Trailer4-40 Towing a Trailer (2.4L L4 Engine)

4-2

Defensive DrivingThe best advice anyone can give about driving is: Drive defensively.

Please start with a very important safety device in yourvehicle: Buckle up. (See “Safety Belts” in the Index.)

Defensive driving really means “be ready for anything.”On city streets, rural roads or freeways, it means“always expect the unexpected.”

Assume that pedestrians or other drivers are going to be careless and make mistakes. Anticipate what theymight do. Be ready for their mistakes.

Rear-end collisions are about the most preventable of accidents. Yet they are common. Allow enoughfollowing distance. It’s the best defensive drivingmaneuver, in both city and rural driving. You neverknow when the vehicle in front of you is going to brakeor turn suddenly.

Defensive driving requires that a driver concentrate onthe driving task. Anything that distracts from the drivingtask -- such as concentrating on a cellular telephone call,reading, or reaching for something on the floor -- makesproper defensive driving more difficult and can evencause a collision, with resulting injury. Ask a passenger tohelp do things like this, or pull off the road in a safe placeto do them yourself. These simple defensive drivingtechniques could save your life.

4-3

Drunken DrivingDeath and injury associated with drinking and driving isa national tragedy. It’s the number one contributor to the highway death toll, claiming thousands of victimsevery year.

Alcohol affects four things that anyone needs to drive a vehicle:

� Judgment

� Muscular Coordination

� Vision

� Attentiveness.

Police records show that almost half of all motorvehicle-related deaths involve alcohol. In most cases,these deaths are the result of someone who was drinkingand driving. In recent years, over 17,000 annual motorvehicle-related deaths have been associated with the useof alcohol, with more than 300,000 people injured.

Many adults -- by some estimates, nearly half the adultpopulation -- choose never to drink alcohol, so theynever drive after drinking. For persons under 21, it’sagainst the law in every U.S. state to drink alcohol.There are good medical, psychological anddevelopmental reasons for these laws.

The obvious way to solve the leading highway safetyproblem is for people never to drink alcohol and thendrive. But what if people do? How much is “too much” ifthe driver plans to drive? It’s a lot less than many mightthink. Although it depends on each person and situation,here is some general information on the problem.

The Blood Alcohol Concentration (BAC) of someonewho is drinking depends upon four things:

� The amount of alcohol consumed

� The drinker’s body weight

� The amount of food that is consumed before andduring drinking

� The length of time it has taken the drinker toconsume the alcohol.

According to the American Medical Association, a 180-lb.(82 kg) person who drinks three 12-ounce (355 ml) bottlesof beer in an hour will end up with a BAC of about 0.06 percent. The person would reach the same BAC bydrinking three 4-ounce (120 ml) glasses of wine or three mixed drinks if each had 1-1/2 ounces (45 ml) of aliquor like whiskey, gin or vodka.

4-4

It’s the amount of alcohol that counts. For example, ifthe same person drank three double martinis (3 ouncesor 90 ml of liquor each) within an hour, the person’sBAC would be close to 0.12 percent. A person whoconsumes food just before or during drinking will have asomewhat lower BAC level.

There is a gender difference, too. Women generally havea lower relative percentage of body water than men.

Since alcohol is carried in body water, this means that awoman generally will reach a higher BAC level than aman of her same body weight when each has the samenumber of drinks.

The law in many U.S. states sets the legal limit at a BACof 0.10 percent. In a growing number of U.S. states, andthroughout Canada, the limit is 0.08 percent. In someother countries, it’s even lower. The BAC limit for allcommercial drivers in the United States is 0.04 percent.

The BAC will be over 0.10 percent after three to sixdrinks (in one hour). Of course, as we’ve seen, itdepends on how much alcohol is in the drinks, and howquickly the person drinks them.

But the ability to drive is affected well below a BAC of0.10 percent. Research shows that the driving skills ofmany people are impaired at a BAC approaching 0.05 percent, and that the effects are worse at night. Alldrivers are impaired at BAC levels above 0.05 percent.Statistics show that the chance of being in a collisionincreases sharply for drivers who have a BAC of 0.05 percent or above. A driver with a BAC level of 0.06 percent has doubled his or her chance of having acollision. At a BAC level of 0.10 percent, the chance ofthis driver having a collision is 12 times greater; at a levelof 0.15 percent, the chance is 25 times greater!

4-5

The body takes about an hour to rid itself of the alcoholin one drink. No amount of coffee or number of coldshowers will speed that up. “I’ll be careful” isn’t theright answer. What if there’s an emergency, a need totake sudden action, as when a child darts into the street?A person with even a moderate BAC might not be ableto react quickly enough to avoid the collision.

There’s something else about drinking and driving thatmany people don’t know. Medical research shows thatalcohol in a person’s system can make crash injuriesworse, especially injuries to the brain, spinal cord orheart. This means that when anyone who has beendrinking -- driver or passenger -- is in a crash, thatperson’s chance of being killed or permanently disabledis higher than if the person had not been drinking.

CAUTION:

Drinking and then driving is very dangerous.Your reflexes, perceptions, attentiveness andjudgment can be affected by even a small amount of alcohol. You can have a serious -- oreven fatal -- collision if you drive after drinking.Please don’t drink and drive or ride with a driverwho has been drinking. Ride home in a cab; or ifyou’re with a group, designate a driver who willnot drink.

4-6

Control of a VehicleYou have three systems that make your vehicle go whereyou want it to go. They are the brakes, the steering andthe accelerator. All three systems have to do their workat the places where the tires meet the road.

Sometimes, as when you’re driving on snow or ice, it’s easy to ask more of those control systems than the tires and road can provide. That means you can lose control of your vehicle.(Also see “Enhanced Traction System” in the Index.)

BrakingBraking action involves perception time and reaction time.

First, you have to decide to push on the brake pedal.That’s perception time. Then you have to bring up your foot and do it. That’s reaction time.

Average reaction time is about 3/4 of a second. But that’s only an average. It might be less with onedriver and as long as two or three seconds or more withanother. Age, physical condition, alertness, coordinationand eyesight all play a part. So do alcohol, drugs andfrustration. But even in 3/4 of a second, a vehiclemoving at 60 mph (100 km/h) travels 66 feet (20 m).That could be a lot of distance in an emergency, sokeeping enough space between your vehicle and othersis important.

And, of course, actual stopping distances vary greatlywith the surface of the road (whether it’s pavement orgravel); the condition of the road (wet, dry, icy); tiretread; the condition of your brakes; the weight of thevehicle and the amount of brake force applied.

4-7

Avoid needless heavy braking. Some people drive in spurts -- heavy acceleration followed by heavy braking -- rather than keeping pace with traffic. This is a mistake. Your brakes may not have time to cool between hard stops. Your brakes will wear outmuch faster if you do a lot of heavy braking. If you keep pace with the traffic and allow realistic followingdistances, you will eliminate a lot of unnecessarybraking. That means better braking and longer brake life.

If your engine ever stops while you’re driving, brakenormally but don’t pump your brakes. If you do, thepedal may get harder to push down. If your enginestops, you will still have some power brake assist. Butyou will use it when you brake. Once the power assist isused up, it may take longer to stop and the brake pedalwill be harder to push.

Anti-Lock Brakes (ABS)Your vehicle has anti-lock brakes (ABS). ABS is anadvanced electronic braking system that will helpprevent a braking skid.

When you start your engine, or when you begin to driveaway, your anti-lock brake system will check itself. Youmay hear a momentary motor or clicking noise whilethis test is going on, and you may even notice that yourbrake pedal moves or pulses a little. This is normal.

If there’s a problem with theanti-lock brake system, thiswarning light will stay on.See “Anti-Lock BrakeSystem Warning Light” inthe Index.

4-8

Here’s how anti-lock works. Let’s say the road is wet.You’re driving safely. Suddenly an animal jumps out infront of you.

You slam on the brakes. Here’s what happens with ABS.

A computer senses that wheels are slowing down. If oneof the wheels is about to stop rolling, the computer willseparately work the brakes at each front wheel and atboth rear wheels.

The anti-lock system can change the brake pressure fasterthan any driver could. The computer is programmed tomake the most of available tire and road conditions.

You can steer around the obstacle while braking hard.

As you brake, your computer keeps receiving updates onwheel speed and controls braking pressure accordingly.

4-9

Remember: Anti-lock doesn’t change the time you needto get your foot up to the brake pedal or always decreasestopping distance. If you get too close to the vehicle infront of you, you won’t have time to apply your brakesif that vehicle suddenly slows or stops. Always leaveenough room up ahead to stop, even though you haveanti-lock brakes.

Using Anti-Lock

Don’t pump the brakes. Just hold the brake pedal downfirmly and let anti-lock work for you. You may feel aslight brake pedal pulsation or notice some noise, butthis is normal.

Braking in EmergenciesWith anti-lock, you can steer and brake at the sametime. In many emergencies, steering can help you morethan even the very best braking.

Enhanced Traction SystemYour vehicle is equipped with an Enhanced TractionSystem (ETS) that limits wheel spin. This is especiallyuseful in slippery road conditions. The system operatesonly if it senses that one or both of the front wheels are spinning or beginning to lose traction. When thishappens, the system reduces engine power and may alsoupshift the transaxle to limit wheel spin.

This light will come onwhen your EnhancedTraction System is limitingwheel spin. See “EnhancedTraction System ActiveLight” in the Index. Youmay feel or hear the systemworking, but this is normal.

This light will also come on when the anti-lock brakesystem is working.

If your vehicle is in cruise control when the enhancedtraction system begins to limit wheel spin, the cruisecontrol will automatically disengage. When roadconditions allow you to safely use it again, you mayreengage the cruise control. (See “Cruise Control” in the Index.)

The Enhanced Traction System operates in all transaxleshift lever positions. But the system can upshift thetransaxle only as high as the shift lever position you’vechosen, so you should use the lower gears only whennecessary. See “Automatic Transaxle” in the Index.

4-10

When the system is on andthe parking brake is fullyreleased, this warning lightwill come on to let youknow if there’s a problem.

See “Enhanced Traction System Warning Light” in theIndex. When this warning light is on, the system will not limit wheel spin. Adjust your driving accordingly.

To limit wheel spin, especially in slippery roadconditions, you should always leave the EnhancedTraction System on. But you can turn the system off if you prefer.

To turn the system on or off, press the ETS button on the the instrument panel.

When you turn the system off, the Enhanced TractionSystem warning light will come on and stay on. If theEnhanced Traction System is limiting wheel spin whenyou press the button to turn the system off, the warninglight will come on -- but the system won’t turn off rightaway. It will wait until there’s no longer a current needto limit wheel spin.

You can turn the system back on at any time by pressingthe button again. The Enhanced Traction Systemwarning light should go off.

4-11

SteeringPower SteeringIf you lose power steering assist because the enginestops or the system is not functioning, you can steer butit will take much more effort.

Variable Effort Steering (If Equipped)

This steering system provides lighter steering effort forparking and at low vehicle speeds. Steering effort willincrease at higher speeds for improved road feel.

Steering Tips

Driving on Curves

It’s important to take curves at a reasonable speed.

A lot of the “driver lost control” accidents mentioned onthe news happen on curves. Here’s why:

Experienced driver or beginner, each of us is subject tothe same laws of physics when driving on curves. Thetraction of the tires against the road surface makes itpossible for the vehicle to change its path when you turnthe front wheels. If there’s no traction, inertia will keepthe vehicle going in the same direction. If you’ve evertried to steer a vehicle on wet ice, you’ll understand this.

The traction you can get in a curve depends on thecondition of your tires and the road surface, the angle atwhich the curve is banked, and your speed. While you’rein a curve, speed is the one factor you can control.

Suppose you’re steering through a sharp curve. Then yousuddenly accelerate. Both control systems -- steering andacceleration -- have to do their work where the tires meetthe road. Adding the sudden acceleration can demand toomuch of those places. You can lose control. Refer to“Enhanced Traction System” in the Index.

What should you do if this ever happens? Ease up on theaccelerator pedal, steer the vehicle the way you want itto go, and slow down.

Speed limit signs near curves warn that you shouldadjust your speed. Of course, the posted speeds arebased on good weather and road conditions. Under lessfavorable conditions you’ll want to go slower.

If you need to reduce your speed as you approach acurve, do it before you enter the curve, while your frontwheels are straight ahead.

Try to adjust your speed so you can “drive” through the curve. Maintain a reasonable, steady speed. Wait toaccelerate until you are out of the curve, and thenaccelerate gently into the straightaway.

4-12

Steering in EmergenciesThere are times when steering can be more effectivethan braking. For example, you come over a hill andfind a truck stopped in your lane, or a car suddenly pullsout from nowhere, or a child darts out from betweenparked cars and stops right in front of you. You canavoid these problems by braking -- if you can stop intime. But sometimes you can’t; there isn’t room. That’s the time for evasive action -- steering around the problem.

Your vehicle can perform very well in emergencies likethese. First apply your brakes. (See “Braking inEmergencies” earlier in this section.) It is better toremove as much speed as you can from a possiblecollision. Then steer around the problem, to the left or right depending on the space available.

An emergency like this requires close attention and aquick decision. If you are holding the steering wheel atthe recommended 9 and 3 o’clock positions, you canturn it a full 180 degrees very quickly without removingeither hand. But you have to act fast, steer quickly, andjust as quickly straighten the wheel once you haveavoided the object.

The fact that such emergency situations are alwayspossible is a good reason to practice defensive driving at all times and wear safety belts properly.

4-13

Off -Road RecoveryYou may find that your right wheels have dropped off theedge of a road onto the shoulder while you’re driving.

If the level of the shoulder is only slightly below thepavement, recovery should be fairly easy. Ease off theaccelerator and then, if there is nothing in the way, steer sothat your vehicle straddles the edge of the pavement. Youcan turn the steering wheel up to one-quarter turn until theright front tire contacts the pavement edge. Then turn yoursteering wheel to go straight down the roadway.

PassingThe driver of a vehicle about to pass another on atwo-lane highway waits for just the right moment,accelerates, moves around the vehicle ahead, then goesback into the right lane again. A simple maneuver?

Not necessarily! Passing another vehicle on a two-lanehighway is a potentially dangerous move, since thepassing vehicle occupies the same lane as oncomingtraffic for several seconds. A miscalculation, an error injudgment, or a brief surrender to frustration or anger can suddenly put the passing driver face to face with theworst of all traffic accidents -- the head-on collision.

So here are some tips for passing:

� “Drive ahead.” Look down the road, to the sides and tocrossroads for situations that might affect your passingpatterns. If you have any doubt whatsoever aboutmaking a successful pass, wait for a better time.

� Watch for traffic signs, pavement markings and lines.If you can see a sign up ahead that might indicate aturn or an intersection, delay your pass. A brokencenter line usually indicates it’s all right to pass(providing the road ahead is clear). Never cross a solidline on your side of the lane or a double solid line,even if the road seems empty of approaching traffic.

4-14

� Do not get too close to the vehicle you want to passwhile you’re awaiting an opportunity. For one thing,following too closely reduces your area of vision,especially if you’re following a larger vehicle. Also, you won’t have adequate space if the vehicleahead suddenly slows or stops. Keep back areasonable distance.

� When it looks like a chance to pass is coming up,start to accelerate but stay in the right lane and don’t get too close. Time your move so you will beincreasing speed as the time comes to move into theother lane. If the way is clear to pass, you will have a“running start” that more than makes up for thedistance you would lose by dropping back. And ifsomething happens to cause you to cancel your pass,you need only slow down and drop back again andwait for another opportunity.

� If other cars are lined up to pass a slow vehicle, waityour turn. But take care that someone isn’t trying topass you as you pull out to pass the slow vehicle.Remember to glance over your shoulder and checkthe blind spot.

� Check your mirrors, glance over your shoulder, andstart your left lane change signal before moving outof the right lane to pass. When you are far enoughahead of the passed vehicle to see its front in yourinside mirror, activate your right lane change signaland move back into the right lane. (Remember thatyour right outside mirror is convex. The vehicle youjust passed may seem to be farther away from youthan it really is.)

� Try not to pass more than one vehicle at a time on two-lane roads. Reconsider before passing thenext vehicle.

� Don’t overtake a slowly moving vehicle too rapidly.Even though the brake lamps are not flashing, it maybe slowing down or starting to turn.

� If you’re being passed, make it easy for thefollowing driver to get ahead of you. Perhaps you can ease a little to the right.

4-15

Loss of ControlLet’s review what driving experts say about whathappens when the three control systems (brakes, steeringand acceleration) don’t have enough friction where thetires meet the road to do what the driver has asked.

In any emergency, don’t give up. Keep trying to steer andconstantly seek an escape route or area of less danger.

SkiddingIn a skid, a driver can lose control of the vehicle.Defensive drivers avoid most skids by taking reasonablecare suited to existing conditions, and by not “overdriving”those conditions. But skids are always possible.

The three types of skids correspond to your vehicle’sthree control systems. In the braking skid, your wheelsaren’t rolling. In the steering or cornering skid, toomuch speed or steering in a curve causes tires to slip andlose cornering force. And in the acceleration skid, toomuch throttle causes the driving wheels to spin.

A cornering skid is best handled by easing your foot offthe accelerator pedal.

If you have the Enhanced Traction System, remember: It helps avoid only the acceleration skid.

If you do not have the Enhanced Traction System, or ifthe system is off, then an acceleration skid is also besthandled by easing your foot off the accelerator pedal.

If your vehicle starts to slide, ease your foot off theaccelerator pedal and quickly steer the way you want thevehicle to go. If you start steering quickly enough, yourvehicle may straighten out. Always be ready for asecond skid if it occurs.

Of course, traction is reduced when water, snow, ice,gravel or other material is on the road. For safety, you’llwant to slow down and adjust your driving to theseconditions. It is important to slow down on slipperysurfaces because stopping distance will be longer andvehicle control more limited.

While driving on a surface with reduced traction, tryyour best to avoid sudden steering, acceleration orbraking (including engine braking by shifting to a lowergear). Any sudden changes could cause the tires to slide.You may not realize the surface is slippery until yourvehicle is skidding. Learn to recognize warning clues -- such as enough water, ice or packed snow onthe road to make a “mirrored surface” -- and slow down when you have any doubt.

Remember: Any anti-lock brake system (ABS) helpsavoid only the braking skid.

4-16

Driving at Night

Night driving is more dangerous than day driving. Onereason is that some drivers are likely to be impaired -- byalcohol or drugs, with night vision problems, or by fatigue.

Here are some tips on night driving.

� Drive defensively.

� Don’t drink and drive.

� Adjust your inside rearview mirror to reduce theglare from headlamps behind you.

� Since you can’t see as well, you may need to slowdown and keep more space between you and other vehicles.

� Slow down, especially on higher speed roads. Yourheadlamps can light up only so much road ahead.

� In remote areas, watch for animals.

� If you’re tired, pull off the road in a safe place and rest.

No one can see as well at night as in the daytime. But aswe get older these differences increase. A 50-year-olddriver may require at least twice as much light to see thesame thing at night as a 20-year-old.

What you do in the daytime can also affect your nightvision. For example, if you spend the day in brightsunshine you are wise to wear sunglasses. Your eyes will have less trouble adjusting to night. But if you’redriving, don’t wear sunglasses at night. They may cutdown on glare from headlamps, but they also make a lotof things invisible.

4-17

You can be temporarily blinded by approachingheadlamps. It can take a second or two, or even several seconds, for your eyes to readjust to the dark.When you are faced with severe glare (as from a driverwho doesn’t lower the high beams, or a vehicle withmisaimed headlamps), slow down a little. Avoid staringdirectly into the approaching headlamps.

Keep your windshield and all the glass on your vehicleclean -- inside and out. Glare at night is made muchworse by dirt on the glass. Even the inside of the glasscan build up a film caused by dust. Dirty glass makeslights dazzle and flash more than clean glass would,making the pupils of your eyes contract repeatedly.

Remember that your headlamps light up far less of aroadway when you are in a turn or curve. Keep youreyes moving; that way, it’s easier to pick out dimlylighted objects. Just as your headlamps should bechecked regularly for proper aim, so should your eyesbe examined regularly. Some drivers suffer from nightblindness -- the inability to see in dim light -- and aren’t even aware of it.

Driving in Rain and on Wet Roads

Rain and wet roads can mean driving trouble. On a wetroad, you can’t stop, accelerate or turn as well becauseyour tire-to-road traction isn’t as good as on dry roads.And, if your tires don’t have much tread left, you’ll geteven less traction. It’s always wise to go slower and becautious if rain starts to fall while you are driving. Thesurface may get wet suddenly when your reflexes aretuned for driving on dry pavement.

4-18

The heavier the rain, the harder it is to see. Even if yourwindshield wiper blades are in good shape, a heavy raincan make it harder to see road signs and traffic signals,pavement markings, the edge of the road and evenpeople walking.

It’s wise to keep your windshield wiping equipment ingood shape and keep your windshield washer tank filled with washer fluid. Replace your windshield wiperinserts when they show signs of streaking or missingareas on the windshield, or when strips of rubber start toseparate from the inserts.

Driving too fast through large water puddles or evengoing through some car washes can cause problems, too.The water may affect your brakes. Try to avoid puddles.But if you can’t, try to slow down before you hit them.

4-19

CAUTION:

Wet brakes can cause accidents. They won’t workas well in a quick stop and may cause pulling toone side. You could lose control of the vehicle.

After driving through a large puddle of water ora car wash, apply your brake pedal lightly untilyour brakes work normally.

HydroplaningHydroplaning is dangerous. So much water can build upunder your tires that they can actually ride on the water.This can happen if the road is wet enough and you’regoing fast enough. When your vehicle is hydroplaning,it has little or no contact with the road.

Hydroplaning doesn’t happen often. But it can if yourtires do not have much tread or if the pressure in one ormore is low. It can happen if a lot of water is standing onthe road. If you can see reflections from trees, telephonepoles or other vehicles, and raindrops “dimple” thewater’s surface, there could be hydroplaning.

Hydroplaning usually happens at higher speeds. Therejust isn’t a hard and fast rule about hydroplaning. Thebest advice is to slow down when it is raining.

Driving Through Deep Standing Water

NOTICE:

If you drive too quickly through deep puddles or standing water, water can come in throughyour engine’s air intake and badly damage yourengine. Never drive through water that is slightlylower than the underbody of your vehicle. If youcan’t avoid deep puddles or standing water, drivethrough them very slowly.

4-20

Driving Through Flowing Water

CAUTION:

Flowing or rushing water creates strong forces. If you try to drive through flowing water, as youmight at a low water crossing, your vehicle can becarried away. As little as six inches of flowingwater can carry away a smaller vehicle. If thishappens, you and other vehicle occupants coulddrown. Don’t ignore police warning signs, andotherwise be very cautious about trying to drivethrough flowing water.

Some Other Rainy Weather Tips� Besides slowing down, allow some extra following

distance. And be especially careful when you passanother vehicle. Allow yourself more clear roomahead, and be prepared to have your view restrictedby road spray.

� Have good tires with proper tread depth. (See “Tires” in the Index.)

City Driving

One of the biggest problems with city streets is theamount of traffic on them. You’ll want to watch out forwhat the other drivers are doing and pay attention totraffic signals.

4-21

Here are ways to increase your safety in city driving:

� Know the best way to get to where you are going. Get a city map and plan your trip into anunknown part of the city just as you would for across-country trip.

� Try to use the freeways that rim and crisscross most large cities. You’ll save time and energy. (See the next part, “Freeway Driving.”)

� Treat a green light as a warning signal. A traffic lightis there because the corner is busy enough to need it.When a light turns green, and just before you start tomove, check both ways for vehicles that have notcleared the intersection or may be running the red light.

Freeway Driving

Mile for mile, freeways (also called thruways, parkways,expressways, turnpikes or superhighways) are the safestof all roads. But they have their own special rules.

4-22

The most important advice on freeway driving is: Keepup with traffic and keep to the right. Drive at the samespeed most of the other drivers are driving. Too-fast ortoo-slow driving breaks a smooth traffic flow. Treat theleft lane on a freeway as a passing lane.

At the entrance, there is usually a ramp that leads to thefreeway. If you have a clear view of the freeway as youdrive along the entrance ramp, you should begin tocheck traffic. Try to determine where you expect toblend with the flow. Try to merge into the gap at close tothe prevailing speed. Switch on your turn signal, checkyour mirrors and glance over your shoulder as often asnecessary. Try to blend smoothly with the traffic flow.

Once you are on the freeway, adjust your speed to theposted limit or to the prevailing rate if it’s slower. Stayin the right lane unless you want to pass.

Before changing lanes, check your mirrors. Then useyour turn signal.

Just before you leave the lane, glance quickly over yourshoulder to make sure there isn’t another vehicle in your“blind” spot.

Once you are moving on the freeway, make certain youallow a reasonable following distance. Expect to moveslightly slower at night.

When you want to leave the freeway, move to the properlane well in advance. If you miss your exit, do not,under any circumstances, stop and back up. Drive on tothe next exit.

The exit ramp can be curved, sometimes quite sharply.

The exit speed is usually posted.

Reduce your speed according to your speedometer, notto your sense of motion. After driving for any distanceat higher speeds, you may tend to think you are goingslower than you actually are.

Before Leaving on a Long TripMake sure you’re ready. Try to be well rested. If youmust start when you’re not fresh -- such as after a day’swork -- don’t plan to make too many miles that first partof the journey. Wear comfortable clothing and shoes youcan easily drive in.

4-23

Is your vehicle ready for a long trip? If you keep itserviced and maintained, it’s ready to go. If it needsservice, have it done before starting out. Of course,you’ll find experienced and able service experts inPontiac dealerships all across North America. They’ll be ready and willing to help if you need it.

Here are some things you can check before a trip:

� Windshield Washer Fluid: Is the reservoir full? Are all windows clean inside and outside?

� Wiper Blades: Are they in good shape?

� Fuel, Engine Oil, Other Fluids: Have you checkedall levels?

� Lamps: Are they all working? Are the lenses clean?

� Tires: They are vitally important to a safe,trouble-free trip. Is the tread good enough forlong-distance driving? Are the tires all inflated to therecommended pressure?

� Weather Forecasts: What’s the weather outlookalong your route? Should you delay your trip a shorttime to avoid a major storm system?

� Maps: Do you have up-to-date maps?

Highway HypnosisIs there actually such a condition as “highway hypnosis”?Or is it just plain falling asleep at the wheel? Call ithighway hypnosis, lack of awareness, or whatever.

There is something about an easy stretch of road with thesame scenery, along with the hum of the tires on the road,the drone of the engine, and the rush of the wind againstthe vehicle that can make you sleepy. Don’t let it happento you! If it does, your vehicle can leave the road in lessthan a second, and you could crash and be injured.

What can you do about highway hypnosis? First, be aware that it can happen.

Then here are some tips:

� Make sure your vehicle is well ventilated, with acomfortably cool interior.

� Keep your eyes moving. Scan the road ahead and tothe sides. Check your rearview mirrors and yourinstruments frequently.

� If you get sleepy, pull off the road into a rest, serviceor parking area and take a nap, get some exercise, orboth. For safety, treat drowsiness on the highway asan emergency.

4-24

Hill and Mountain Roads

Driving on steep hills or mountains is different fromdriving in flat or rolling terrain.

If you drive regularly in steep country, or if you’replanning to visit there, here are some tips that can makeyour trips safer and more enjoyable.

� Keep your vehicle in good shape. Check all fluidlevels and also the brakes, tires, cooling system and transaxle. These parts can work hard onmountain roads.

� Know how to go down hills. The most importantthing to know is this: let your engine do some of theslowing down. Shift to a lower gear when you godown a steep or long hill.

CAUTION:

If you don’t shift down, your brakes could get sohot that they wouldn’t work well. You would thenhave poor braking or even none going down a hill.You could crash. Shift down to let your engineassist your brakes on a steep downhill slope.

4-25

CAUTION:

Coasting downhill in NEUTRAL (N) or with theignition off is dangerous. Your brakes will have todo all the work of slowing down. They could getso hot that they wouldn’t work well. You wouldthen have poor braking or even none going down a hill. You could crash. Always have yourengine running and your vehicle in gear whenyou go downhill.

� Know how to go uphill. Drive in the highest gear possible.

� Stay in your own lane when driving on two-laneroads in hills or mountains. Don’t swing wide or cutacross the center of the road. Drive at speeds that letyou stay in your own lane.

� As you go over the top of a hill, be alert. There could besomething in your lane, like a stalled car or an accident.

� You may see highway signs on mountains that warn ofspecial problems. Examples are long grades, passing orno-passing zones, a falling rocks area or windingroads. Be alert to these and take appropriate action.

Winter Driving

Here are some tips for winter driving:

� Have your vehicle in good shape for winter.

� You may want to put winter emergency supplies inyour trunk.

4-26

Include an ice scraper, a small brush or broom, a supplyof windshield washer fluid, a rag, some winter outerclothing, a small shovel, a flashlight, a red cloth and acouple of reflective warning triangles. And, if you willbe driving under severe conditions, include a small bagof sand, a piece of old carpet or a couple of burlap bagsto help provide traction. Be sure you properly securethese items in your vehicle.

Driving on Snow or IceMost of the time, those places where your tires meet theroad probably have good traction.

However, if there is snow or ice between your tires andthe road, you can have a very slippery situation. You’llhave a lot less traction or “grip” and will need to be very careful.

4-27

What’s the worst time for this? “Wet ice.” Very coldsnow or ice can be slick and hard to drive on. But wetice can be even more trouble because it may offer theleast traction of all. You can get wet ice when it’s aboutfreezing (32�F; 0�C) and freezing rain begins to fall.Try to avoid driving on wet ice until salt and sand crewscan get there.

Whatever the condition -- smooth ice, packed, blowingor loose snow -- drive with caution.

Keep your Enhanced Traction System on. It will improveyour ability to accelerate when driving on a slippery road.Even though your vehicle has this system, you’ll want toslow down and adjust your driving to the road conditions.See “Enhanced Traction System” in the Index.

Your anti-lock brakes improve your vehicle’s stabilitywhen you make a hard stop on a slippery road. Eventhough you have the anti-lock braking system, you’llwant to begin stopping sooner than you would on drypavement. See “Anti-Lock” in the Index.

� Allow greater following distance on any slippery road.

� Watch for slippery spots. The road might be fineuntil you hit a spot that’s covered with ice. On anotherwise clear road, ice patches may appear inshaded areas where the sun can’t reach: aroundclumps of trees, behind buildings or under bridges.Sometimes the surface of a curve or an overpass mayremain icy when the surrounding roads are clear. Ifyou see a patch of ice ahead of you, brake before youare on it. Try not to brake while you’re actually onthe ice, and avoid sudden steering maneuvers.

4-28

If You’re Caught in a Blizzard

If you are stopped by heavy snow, you could be in aserious situation. You should probably stay with yourvehicle unless you know for sure that you are near helpand you can hike through the snow. Here are somethings to do to summon help and keep yourself and yourpassengers safe:

� Turn on your hazard flashers.

� Tie a red cloth to your vehicle to alert police thatyou’ve been stopped by the snow.

� Put on extra clothing or wrap a blanket around you.If you have no blankets or extra clothing, make bodyinsulators from newspapers, burlap bags, rags, floormats -- anything you can wrap around yourself ortuck under your clothing to keep warm.

You can run the engine to keep warm, but be careful.

4-29

CAUTION:

Snow can trap exhaust gases under your vehicle.This can cause deadly CO (carbon monoxide) gasto get inside. CO could overcome you and killyou. You can’t see it or smell it, so you might notknow it is in your vehicle. Clear away snow fromaround the base of your vehicle, especially anythat is blocking your exhaust pipe. And checkaround again from time to time to be sure snowdoesn’t collect there.Open a window just a little on the side of thevehicle that’s away from the wind. This will helpkeep CO out.

Run your engine only as long as you must. This savesfuel. When you run the engine, make it go a little fasterthan just idle. That is, push the accelerator slightly. Thisuses less fuel for the heat that you get and it keeps thebattery charged.

You will need a well-charged battery to restart thevehicle, and possibly for signaling later on with yourheadlamps. Let the heater run for a while.

Then, shut the engine off and close the window almostall the way to preserve the heat. Start the engine againand repeat this only when you feel really uncomfortablefrom the cold. But do it as little as possible. Preserve thefuel as long as you can. To help keep warm, you can getout of the vehicle and do some fairly vigorous exercisesevery half hour or so until help comes.

Recreational Vehicle TowingYou can tow your vehicle behind another vehicle for useat your destination. Be sure to use the proper towingequipment designed for recreational towing. Follow theinstructions for the towing equipment.

Towing Your Vehicle from the FrontThere are two ways to tow your vehicle from the front.

4-30

To tow your vehicle with a dolly, follow these steps:

� Put the front wheels on a dolly.

� Put the vehicle in PARK (P) for automatic transaxleand NEUTRAL for a manual transaxle.

� Set the parking brake and then remove the key.

� Clamp the steering wheel in a straight-ahead positionwith a clamping device designed for towing.

� Release the parking brake.

To tow your vehicle with all four wheels on the ground,follow these steps:

1. Position the vehicle to tow and then secure it.

2. Turn the ignition switch to OFF.

3. Set the parking brake.

4-31

4. Remove the following fuses from the left side of theinstrument panel fuse block: A) RADIO SW, B) RADIO ACC, C) WIPER, H) BFC BATT, I) PCM BATT, K) IPC/BFC ACC. This will prevent your battery from draining while towing. See “Instrument Panel Fuse Block - Left” in Section 6 for the location of these fuses.

5. Turn the ignition switch to ACC.

6. Shift your transaxle to NEUTRAL (N).

7. Release the parking brake.

Remember to replace the fuses once you reach yourdestination. To replace a fuse:

1. Set the parking brake.

2. Remove the key from the ignition switch.

3. Replace the fuse.

NOTICE:

Make sure that the towing speed does not exceed65 mph (110 km/h), or your vehicle could bebadly damaged.

Towing Your Vehicle from the Rear

NOTICE:

Do not tow your vehicle from the rear. Yourvehicle could be badly damaged and the repairswould not be covered by your warranty.

4-32

Loading Your Vehicle

Two labels on your vehicle show how much weight itmay properly carry. The Tire-Loading Information labelfound on the rear edge of the driver’s door tells you theproper size, speed rating and recommended inflationpressures for the tires on your vehicle. It also gives youimportant information about the number of people thatcan be in your vehicle and the total weight that you cancarry. This weight is called the Vehicle Capacity Weight,and includes the weight of all occupants, cargo and allnonfactory-installed options.

The other label is the Certification label, found on the rearedge of the driver’s door. It tells you the gross weightcapacity of your vehicle, called the Gross Vehicle WeightRating (GVWR). The GVWR includes the weight of thevehicle, all occupants, fuel and cargo. Never exceed theGVWR for your vehicle, or the Gross Axle Weight Rating(GAWR) for either the front or rear axle.

And, if you do have a heavy load, you should spread it out. Don’t carry more than 132 lbs. (60 kg) in your trunk.

4-33

CAUTION:

Do not load your vehicle any heavier than theGVWR, or either the maximum front or rearGAWR. If you do, parts on your vehicle canbreak, and it can change the way your vehiclehandles. These could cause you to lose controland crash. Also, overloading can shorten the lifeof your vehicle.

CAUTION:

Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash.� Put things in the trunk of your vehicle. In a

trunk, put them as far forward as you can.Try to spread the weight evenly.

� Never stack heavier things, like suitcases,inside the vehicle so that some of them areabove the tops of the seats.

� Don’t leave an unsecured child restraint inyour vehicle.

� When you carry something inside thevehicle, secure it whenever you can.

� Don’t leave a seat folded down unless you need to.

4-34

Towing a Trailer

CAUTION:

If you don’t use the correct equipment and driveproperly, you can lose control when you pull atrailer. For example, if the trailer is too heavy, thebrakes may not work well -- or even at all. Youand your passengers could be seriously injured.You may also damage your vehicle; the resultingrepairs would not be covered by your warranty.Pull a trailer only if you have followed all thesteps in this section. Ask your dealer for adviceand information about towing a trailer with your vehicle.

Do not tow a trailer if your vehicle is equipped with a2.4L L4 (Code T) engine.

Your vehicle can tow a trailer if it is equipped with theproper trailer towing equipment. To identify what thevehicle trailering capacity is for your vehicle, youshould read the information in “Weight of the Trailer”that appears later in this section. But trailering isdifferent than just driving your vehicle by itself.Trailering means changes in handling, durability andfuel economy. Successful, safe trailering takes correctequipment, and it has to be used properly.

That’s the reason for this part. In it are manytime-tested, important trailering tips and safety rules.Many of these are important for your safety and that ofyour passengers. So please read this section carefullybefore you pull a trailer.

Load-pulling components such as the engine, transaxle,wheel assemblies and tires are forced to work harderagainst the drag of the added weight. The engine isrequired to operate at relatively higher speeds and undergreater loads, generating extra heat. What’s more, thetrailer adds considerably to wind resistance, increasingthe pulling requirements.

4-35

If You Do Decide To Pull A TrailerIf you do, here are some important points:

� There are many different laws, including speed limitrestrictions, having to do with trailering. Make sureyour rig will be legal, not only where you live butalso where you’ll be driving. A good source for thisinformation can be state or provincial police.

� Consider using a sway control. You can ask a hitchdealer about sway controls.

� Don’t tow a trailer at all during the first 1,000 miles(1 600 km) your new vehicle is driven. Your engine,axle or other parts could be damaged.

� Then, during the first 500 miles (800 km) that youtow a trailer, don’t drive over 50 mph (80 km/h) anddon’t make starts at full throttle. This helps yourengine and other parts of your vehicle wear in at theheavier loads.

� Obey speed limit restrictions when towing a trailer.Don’t drive faster than the maximum posted speedfor trailers (or no more than 55 mph (90 km/h)) tosave wear on your vehicle’s parts.

Three important considerations have to do with weight:

� the weight of the trailer,

� the weight of the trailer tongue

� and the total weight on your vehicle’s tires.

Weight of the TrailerHow heavy can a trailer safely be?

It should never weigh more than 1,000 lbs. (450 kg). But even that can be too heavy.

It depends on how you plan to use your rig. For example,speed, altitude, road grades, outside temperature and how much your vehicle is used to pull a trailer are allimportant. And, it can also depend on any specialequipment that you have on your vehicle.

You can ask your dealer for our trailering information oradvice, or you can write us at:

Pontiac Customer Assistance Center31 E. Judson St.Pontiac, MI 48342

In Canada, write to:General Motors of Canada LimitedCustomer Communication Centre1908 Colonel Sam DriveOshawa, Ontario L1H 8P7

4-36

Weight of the Trailer TongueThe tongue load (A) of any trailer is an importantweight to measure because it affects the total or grossweight of your vehicle. The Gross Vehicle Weight(GVW) includes the curb weight of the vehicle, anycargo you may carry in it, and the people who will beriding in the vehicle. And if you tow a trailer, you mustadd the tongue load to the GVW because your vehiclewill be carrying that weight, too. See “Loading YourVehicle” in the Index for more information about yourvehicle’s maximum load capacity.

If you’re using a weight-carrying hitch, the trailertongue (A) should weigh 10 percent of the total loadedtrailer weight (B). If you have a weight-distributinghitch, the trailer tongue (A) should weigh 12 percent ofthe total loaded trailer weight (B).

After you’ve loaded your trailer, weigh the trailer andthen the tongue, separately, to see if the weights areproper. If they aren’t, you may be able to get them right simply by moving some items around in the trailer.

Total Weight on Your Vehicle’s TiresBe sure your vehicle’s tires are inflated to the upperlimit for cold tires. You’ll find these numbers on theCertification label at the rear edge of the driver’s door orsee “Loading Your Vehicle” in the Index. Then be sure you don’t go over the GVW limit for your vehicle,including the weight of the trailer tongue.

4-37

HitchesIt’s important to have the correct hitch equipment.Crosswinds, large trucks going by and rough roads are afew reasons why you’ll need the right hitch. Here aresome rules to follow:

� The rear bumper on your vehicle is not intended for hitches. Do not attach rental hitches or otherbumper-type hitches to it. Use only a frame-mountedhitch that does not attach to the bumper.

� Will you have to make any holes in the body of your vehicle when you install a trailer hitch? If you do, then be sure to seal the holes later when you remove the hitch. If you don’t seal them, deadly carbon monoxide (CO) from your exhaust can get into your vehicle (see “Carbon Monoxide” in the Index). Dirt and water can, too.

Safety ChainsYou should always attach chains between your vehicleand your trailer. Cross the safety chains under the tongueof the trailer so that the tongue will not drop to the roadif it becomes separated from the hitch. Instructionsabout safety chains may be provided by the hitchmanufacturer or by the trailer manufacturer. Follow themanufacturer’s recommendation for attaching safetychains and do not attach them to the bumper. Alwaysleave just enough slack so you can turn with your rig.And, never allow safety chains to drag on the ground.

Trailer BrakesDoes your trailer have its own brakes?

Be sure to read and follow the instructions for the trailerbrakes so you’ll be able to install, adjust and maintainthem properly. And because you have anti-lock brakes,do not try to tap into your vehicle’s brake system. If youdo, both systems won’t work well, or at all.

Driving with a TrailerTowing a trailer requires a certain amount of experience.Before setting out for the open road, you’ll want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of thetrailer. And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly asresponsive as your vehicle is by itself.

Before you start, check the trailer hitch and platform(and attachments), safety chains, electrical connector,lamps, tires and mirror adjustment. If the trailer haselectric brakes, start your vehicle and trailer moving andthen apply the trailer brake controller by hand to be surethe brakes are working. This lets you check yourelectrical connection at the same time.

4-38

During your trip, check occasionally to be sure that theload is secure, and that the lamps and any trailer brakesare still working.

Following DistanceStay at least twice as far behind the vehicle ahead as youwould when driving your vehicle without a trailer. Thiscan help you avoid situations that require heavy brakingand sudden turns.

PassingYou’ll need more passing distance up ahead whenyou’re towing a trailer. And, because you’re a good deallonger, you’ll need to go much farther beyond thepassed vehicle before you can return to your lane.

Backing UpHold the bottom of the steering wheel with one hand.Then, to move the trailer to the left, just move that handto the left. To move the trailer to the right, move yourhand to the right. Always back up slowly and, ifpossible, have someone guide you.

Making Turns

NOTICE:

Making very sharp turns while trailering couldcause the trailer to come in contact with thevehicle. Your vehicle could be damaged. Avoidmaking very sharp turns while trailering.

When you’re turning with a trailer, make wider turns thannormal. Do this so your trailer won’t strike soft shoulders,curbs, road signs, trees or other objects. Avoid jerky orsudden maneuvers. Signal well in advance.

Turn Signals When Towing a TrailerWhen you tow a trailer, your vehicle may need adifferent turn signal flasher and/or extra wiring. Checkwith your dealer. The arrows on your instrument panelwill flash whenever you signal a turn or lane change.Properly hooked up, the trailer lamps will also flash,telling other drivers you’re about to turn, change lanes or stop.

4-39

When towing a trailer, the arrows on your instrument panel will flash for turns even if the bulbs on the trailer are burned out. Thus, you may think drivers behind you are seeing your signal when they are not. It’s important to check occasionally to be sure the trailer bulbs are still working.

Driving On GradesReduce speed and shift to a lower gear before you startdown a long or steep downgrade. If you don’t shiftdown, you might have to use your brakes so much thatthey would get hot and no longer work well.

On a long uphill grade, shift down and reduce yourspeed to around 45 mph (70 km/h) to reduce thepossibility of engine and transaxle overheating.

Parking on Hills

CAUTION:

You really should not park your vehicle, with atrailer attached, on a hill. If something goeswrong, your rig could start to move. People canbe injured, and both your vehicle and the trailercan be damaged.

But if you ever have to park your rig on a hill, here’show to do it:

1. Apply your regular brakes, but don’t shift into PARK (P) for an automatic transaxle yet, or into gearfor a manual transaxle. When parking uphill, turnyour wheels away from the curb. When parkingdownhill, turn your wheels into the curb.

2. Have someone place chocks under the trailer wheels.

3. When the chocks are in place, release the regularbrakes until the chocks absorb the load.

4. Reapply the regular brakes. Then apply your parkingbrake and shift into PARK (P) (for an automatictransaxle), or REVERSE (R) for a manual transaxle.

5. Release the regular brakes.

4-40

When You Are Ready to Leave AfterParking on a Hill1. Apply your regular brakes and hold the pedal down

while you:

� Start your engine;

� Shift into a gear; and

� Release the parking brake.

2. Let up on the brake pedal.

3. Drive slowly until the trailer is clear of the chocks.

4. Stop and have someone pick up and store the chocks.

Maintenance When Trailer TowingYour vehicle will need service more often when you’repulling a trailer. See the Maintenance Schedule for moreon this. Things that are especially important in traileroperation are automatic transaxle fluid (don’t overfill),engine oil, drive belt, cooling system and brake system.Each of these is covered in this manual, and the Indexwill help you find them quickly. If you’re trailering, it’sa good idea to review this information before you startyour trip.

Check periodically to see that all hitch nuts and bolts are tight.

Engine Cooling When Trailer TowingYour cooling system may temporarily overheat duringsevere operating conditions. See “Engine Overheating”in the Index.

Towing a Trailer (2.4L L4 Engine)Your vehicle is neither designed nor intended to tow atrailer if it is equipped with a 2.4L L4 engine.

5-5-1

Section 5 Problems on the Road

Here you’ll find what to do about some problems that can occur on the road.

5-2 Hazard Warning Flashers5-3 Other Warning Devices5-3 Jump Starting5-8 Towing Your Vehicle5-9 Engine Overheating5-11 Cooling System

5-18 If a Tire Goes Flat5-19 Changing a Flat Tire5-28 Compact Spare Tire5-29 If You’re Stuck: In Sand, Mud, Ice or Snow

5-2

Hazard Warning Flashers

Your hazard warning flashers let you warn others. Theyalso let police know you have a problem. Your front andrear turn signal lamps will flash on and off.

Press the button on the instrument panel to make yourfront and rear turn signal lamps flash on and off.

Your hazard warning flashers work no matter whatposition your key is in, and even if the key isn’t in.

To turn off the flashers, press the button.

When the hazard warning flashers are on, your turnsignals won’t work.

5-3

Other Warning DevicesIf you carry reflective triangles, you can set one up atthe side of the road about 300 feet (100 m) behind your vehicle.

Jump StartingIf your battery has run down, you may want to useanother vehicle and some jumper cables to start yourvehicle. But please follow the steps here to do it safely.

CAUTION:

Batteries can hurt you. They can be dangerous because:� They contain acid that can burn you.� They contain gas that can explode or ignite.� They contain enough electricity to

burn you.If you don’t follow these steps exactly, some or allof these things can hurt you.

NOTICE:

Ignoring these steps could result in costly damageto your vehicle that wouldn’t be covered by your warranty.

The ACDelco� battery in your vehicle has abuilt -in hydrometer. Do not charge, test or jumpstart the battery if the hydrometer looks clear orlight yellow. Replace the battery when there is a clear or light yellow hydrometer and acranking complaint.Trying to start your vehicle by pushing or pullingit won’t work, and it could damage your vehicle.

5-4

1. Check the other vehicle. It must have a 12-voltbattery with a negative ground system.

NOTICE:

If the other system isn’t a 12-volt system with anegative ground, both vehicles can be damaged.

2. Get the vehicles close enough so the jumper cablescan reach, but be sure the vehicles aren’t touchingeach other. If they are, it could cause a groundconnection you don’t want. You wouldn’t be able tostart your vehicle, and the bad grounding coulddamage the electrical systems. To avoid thepossibility of the vehicles rolling, set the parkingbrake firmly on both vehicles involved in the jumpstart procedure. Put an automatic transaxle in PARK (P) or a manual transaxle in NEUTRALbefore setting the parking brake.

3. Turn off the ignition on both vehicles. Unplugunnecessary accessories plugged into the cigarettelighter. Turn off all lamps that aren’t needed as wellas radios. This will avoid sparks and help save bothbatteries. In addition, it could save your radio!

NOTICE:

If you leave your radio on, it could be badlydamaged. The repairs wouldn’t be covered byyour warranty.

4. Open the hoods and locate the batteries.

CAUTION:

An electric fan can start up even when the engineis not running and can injure you. Keep hands,clothing and tools away from any underhoodelectric fan.

5-5

5. Find the positive (+) and negative (-) terminals oneach battery.

CAUTION:

Using a match near a battery can cause batterygas to explode. People have been hurt doing this,and some have been blinded. Use a flashlight ifyou need more light.Be sure the battery has enough water. You don’tneed to add water to the ACDelco� batteryinstalled in every new GM vehicle. But if abattery has filler caps, be sure the right amountof fluid is there. If it is low, add water to take careof that first. If you don’t, explosive gas could be present.

Battery fluid contains acid that can burn you.Don’t get it on you. If you accidentally get it inyour eyes or on your skin, flush the place withwater and get medical help immediately.

6. Check that the jumper cables don’t have loose ormissing insulation. If they do, you could get a shock.The vehicles could be damaged, too.

Before you connect the cables, here are some basicthings you should know. Positive (+) will go topositive (+) and negative (-) will go to a heavyunpainted metal engine part.

Don’t connect positive (+) to negative (-) or you’llget a short that would damage the battery and maybeother parts, too.

CAUTION:

Fans or other moving engine parts can injure youbadly. Keep your hands away from moving partsonce the engine is running.

5-6

7. Connect the red positive (+) cable to the positive (+)terminal of the vehicle with the dead battery.

8. Don’t let the other endtouch metal. Connect itto the positive (+)terminal of the goodbattery. Use a remotepositive (+) terminal ifthe vehicle has one.

9. Now connect the black negative (-) cable to the goodbattery’s negative (-) terminal.

5-7

Don’t let the other end touch anything until the nextstep. The other end of the negative cable doesn’t go tothe dead battery. It goes to a heavy unpainted metalpart on the engine of the vehicle with the dead battery.

10. Attach the cable at least 18 inches (45 cm) awayfrom the dead battery, but not near engine parts thatmove. The electrical connection is just as goodthere, but the chance of sparks getting back to thebattery is much less.

11. If the SECURITY light flashes, leave the ignition to ONand wait until the light stops flashing. Turn the ignition to OFF for three seconds then start the vehicle with the good battery and run the engine for a while.

12. Try to start the vehicle with the dead battery.

If it won’t start after a few tries, it probably needs service.

13. Remove the cables in reverse order to preventelectrical shorting. Take care that they don’t toucheach other or any other metal.

A. Heavy Unpainted Metal Engine Part

B. Good Battery

C. Dead Battery

5-8

Towing Your Vehicle

CAUTION:

To help avoid serious personal injury to you or others:� Never let passengers ride in a vehicle that is

being towed.� Never tow faster than safe or posted speeds.� Never tow with damaged parts not

fully secured.� Never get under your vehicle after it has

been lifted by the tow truck.� Always secure the vehicle on each side with

separate safety chains when towing it.� Use only the correct hooks.

NOTICE:

Use the proper towing equipment to avoiddamage to the bumper, fascia or fog lamp areasof the vehicle.

With current trends in automotive styles and design, it is essential that the correct towing equipment is used totow a vehicle. Your vehicle can be towed with wheel-liftequipment or car-carrier equipment.

Consult your dealer or a professional towing service ifyou need to have your vehicle towed. See “RoadsideAssistance” in the Index.

5-9

Engine OverheatingYou will find a coolant temperature gage and a lowcoolant warning light on your vehicle’s instrumentpanel. See “Engine Coolant Temperature Gage” and“Low Coolant Warning Light” in the Index.

If Steam Is Coming From Your Engine

CAUTION:

Steam from an overheated engine can burn youbadly, even if you just open the hood. Stay awayfrom the engine if you see or hear steam comingfrom it. Just turn it off and get everyone awayfrom the vehicle until it cools down. Wait untilthere is no sign of steam or coolant before youopen the hood.

If you keep driving when your engine isoverheated, the liquids in it can catch fire. You or others could be badly burned. Stop yourengine if it overheats, and get out of the vehicleuntil the engine is cool.

NOTICE:

If your engine catches fire because you keepdriving with no coolant, your vehicle can bebadly damaged. The costly repairs would not be covered by your warranty.

5-10

If No Steam Is Coming From Your EngineIf you get an engine overheat warning but see or hear nosteam, the problem may not be too serious. Sometimesthe engine can get a little too hot when you:

� Climb a long hill on a hot day.

� Stop after high-speed driving.

� Idle for long periods in traffic.

� Tow a trailer.

If you get the overheat warning with no sign of steam,try this for a minute or so:

1. If your air conditioner is on, turn it off.

2. Turn on your heater to full hot at the highest fanspeed and open the window as necessary.

3. If you’re in a traffic jam, shift to NEUTRAL (N);otherwise, shift to the highest gear while driving --AUTOMATIC OVERDRIVE (D) orTHIRD (3) for an automatic transaxle, or shift toNEUTRAL or otherwise to the highest gear whiledriving -- FIFTH (5) or FORTH (4) for a manual transaxle.

If you no longer have the overheat warning, you can drive. Just to be safe, drive slower for about 10 minutes. If the warning doesn’t come back on, youcan drive normally.

If the warning continues, pull over, stop, and park yourvehicle right away.

If there’s still no sign of steam, idle the engine for three minutes while you’re parked. If you still have thewarning, turn off the engine and get everyone out of thevehicle until it cools down.

You may decide not to lift the hood but to get servicehelp right away.

5-11

Cooling SystemWhen you decide it’s safe to lift the hood, here’s whatyou’ll see:

A. Coolant Surge Tank with Pressure Cap

B. Electric Engine Cooling Fan

CAUTION:

An electric engine cooling fan under the hood canstart up even when the engine is not running andcan injure you. Keep hands, clothing and toolsaway from any underhood electric fan.

If the coolant inside the coolant surge tank is boiling,don’t do anything else until it cools down.

5-12

When the engine is cold, the coolant level should be ator above FULL COLD. If it isn’t, you may have a leakin the radiator hoses, heater hoses, radiator, water pumpor somewhere else in the cooling system.

CAUTION:

Heater and radiator hoses, and other engineparts, can be very hot. Don’t touch them. If youdo, you can be burned.

Don’t run the engine if there is a leak. If you runthe engine, it could lose all coolant. That couldcause an engine fire, and you could be burned.Get any leak fixed before you drive the vehicle.

5-13

NOTICE:

Engine damage from running your enginewithout coolant isn’t covered by your warranty.

NOTICE:

When adding coolant, it is important that you use only DEX-COOL� (silicate-free) coolant.If coolant other than DEX-COOL is added to the system, premature engine, heater core orradiator corrosion may result. In addition, theengine coolant will require change sooner -- at30,000 miles (50 000 km) or 24 months,whichever occurs first. Damage caused by the use of coolant other than DEX-COOL� is notcovered by your new vehicle warranty.

If there seems to be no leak, with the engine on, check tosee if the electric engine cooling fans are running. If theengine is overheating, both fans should be running. Ifthey aren’t, your vehicle needs service.

5-14

How to Add Coolant to the Coolant Surge TankIf you haven’t found a problem yet, but the coolant levelisn’t at or above FULL COLD, add a 50/50 mixture ofclean, drinkable water and DEX-COOL� coolant at thecoolant surge tank, but be sure the cooling system,including the coolant surge tank pressure cap, is coolbefore you do it. (See “Engine Coolant” in the Index formore information.)

CAUTION:

Steam and scalding liquids from a hot coolingsystem can blow out and burn you badly. They areunder pressure, and if you turn the coolant surgetank pressure cap -- even a little -- they can comeout at high speed. Never turn the cap when thecooling system, including the coolant surge tankpressure cap, is hot. Wait for the cooling systemand coolant surge tank pressure cap to cool if youever have to turn the pressure cap.

5-15

CAUTION:

Adding only plain water to your cooling systemcan be dangerous. Plain water, or some otherliquid like alcohol, can boil before the propercoolant mixture will. Your vehicle’s coolantwarning system is set for the proper coolantmixture. With plain water or the wrong mixture,your engine could get too hot but you wouldn’tget the overheat warning. Your engine couldcatch fire and you or others could be burned. Use a 50/50 mixture of clean, drinkable waterand DEX-COOL� coolant.

NOTICE:

In cold weather, water can freeze and crack theengine, radiator, heater core and other parts. So use the recommended coolant.

CAUTION:

You can be burned if you spill coolant on hotengine parts. Coolant contains ethylene glycoland it will burn if the engine parts are hotenough. Don’t spill coolant on a hot engine.

5-16

1. You can remove the coolant surge tank pressure cap when the cooling system, including the coolantsurge tank pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowlycounterclockwise (left) about two or two andone-half turns. If you hear a hiss, wait for that tostop. This will allow any pressure still left to bevented out the discharge hose.

2. Then keep turning the pressure cap slowly, andremove it.

5-17

3. Then fill the coolant surge tank with the propermixture, to FULL COLD mark.

4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upperradiator hose getting hot. Watch out for the enginecooling fans.

By this time, the coolant level inside the coolantsurge tank may be lower. If the level is lower, addmore of the proper mixture to the coolant surge tankuntil the level reaches the FULL COLD mark.

5-18

5. Then replace the pressure cap. Be sure the pressurecap is hand-tight.

Check the level in the surge tank when the coolingsystem has cooled down. If the coolant isn’t at theproper level, repeat Steps 1 to 3 and reinstall thepressure cap or see your dealer.

If a Tire Goes FlatIt’s unusual for a tire to “blow out” while you’re driving,especially if you maintain your tires properly. If air goesout of a tire, it’s much more likely to leak out slowly.But if you should ever have a “blowout,” here are a few tips about what to expect and what to do:

If a front tire fails, the flat tire will create a drag thatpulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly.Steer to maintain lane position, and then gently brake toa stop well out of the traffic lane.

A rear blowout, particularly on a curve, acts much like askid and may require the same correction you’d use in a skid. In any rear blowout, remove your foot fromthe accelerator pedal. Get the vehicle under control bysteering the way you want the vehicle to go. It may bevery bumpy and noisy, but you can still steer. Gentlybrake to a stop -- well off the road if possible.

If a tire goes flat, the next part shows how to use yourjacking equipment to change a flat tire safely.

5-19

Changing a Flat TireIf a tire goes flat, avoid further tire and wheel damageby driving slowly to a level place. Turn on your hazardwarning flashers.

CAUTION:

Changing a tire can cause an injury. The vehiclecan slip off the jack and roll over you or otherpeople. You and they could be badly injured.Find a level place to change your tire. To helpprevent the vehicle from moving:

1. Set the parking brake firmly.2. Put an automatic transaxle shift lever in

PARK (P), or shift a manual transaxle toFIRST (1) or REVERSE (R).

3. Turn off the engine.

To be even more certain the vehicle won’t move,you can put blocks at the front and rear of thetire farthest away from the one being changed.That would be the tire on the other side of thevehicle, at the opposite end.

The following steps will tell you how to use the jack andchange a tire.

5-20

Removing the Spare Tire and Tools

The equipment you’ll needis in the trunk.

Pull the carpeting from the floor of the trunk. Turn the center retainer nut on the compact spare covercounterclockwise to remove it.

Lift and remove the cover. See “Compact Spare Tire”later in this section for more information about thecompact spare.

Turn the wing nutcounterclockwise andremove it. Then lift off the spacer and remove thespare tire.

Remove the jack and wheel wrench from the trunk. Your vehicle’s jack and wheel wrench are stored in afoam tray. Remove the band around the jack.

5-21

The tools you’ll be using include the jack (A) and wheelwrench (B).

Removing the Flat Tire and Installing theSpare Tire1. Remove the wheel nut caps (you may need to use the

wheel wrench to loosen and remove them, if yourfingers do not fit into this small area).

2. Then use the wheel wrench to loosen all the wheel nuts.Don’t remove them yet.

5-22

3. Position the jack and raise the jack head until it fitsfirmly into the notch in the vehicle’s frame nearestthe flat tire. Put the compact spare tire near you.

CAUTION:

Getting under a vehicle when it is jacked up isdangerous. If the vehicle slips off the jack, youcould be badly injured or killed. Never get undera vehicle when it is supported only by a jack.

CAUTION:

Raising your vehicle with the jack improperlypositioned can damage the vehicle and even makethe vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lifthead into the proper location before raising the vehicle.

5-23

4. Raise the vehicle by turning the wheel wrenchclockwise. Raise the vehicle far enough off the groundso there is enough room for the spare tire to fit.

5. Remove all of the wheel nuts.

6. Remove the flat tire.

7. Remove any rust or dirtfrom the wheel bolts,mounting surfaces andspare wheel.

CAUTION:

Rust or dirt on the wheel, or on the parts towhich it is fastened, can make the wheel nutsbecome loose after a time. The wheel could comeoff and cause an accident. When you change awheel, remove any rust or dirt from the placeswhere the wheel attaches to the vehicle. In anemergency, you can use a cloth or a paper towelto do this; but be sure to use a scraper or wirebrush later, if you need to, to get all the rust or dirt off.

5-24

CAUTION:

Never use oil or grease on studs or nuts. If youdo, the nuts might come loose. Your wheel couldfall off, causing a serious accident.

8. Install the compact spare tire. Replace the wheel andnuts with the rounded end of the nuts toward thewheel. Tighten each nut by hand until the wheel isheld against the hub.

9. Lower the vehicle by turning the wheel wrenchcounterclockwise. Lower the jack completely.

5-25

10. Tighten the wheel nuts firmly in a crisscrosssequence, as shown.

CAUTION:

Incorrect wheel nuts or improperly tightenedwheel nuts can cause the wheel to become looseand even come off. This could lead to an accident.Be sure to use the correct wheel nuts. If you haveto replace them, be sure to get new GM originalequipment wheel nuts.Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to 100 lb-ft (140 N·m).

NOTICE:

Improperly tightened wheel nuts can lead tobrake pulsation and rotor damage. To avoidexpensive brake repairs, evenly tighten the wheelnuts in the proper sequence and to the propertorque specification.

NOTICE:

Wheel covers won’t fit on your compact spare. If you try to put a wheel cover on your compactspare, you could damage the cover or the spare.

5-26

Storing the Flat Tire and Tools

CAUTION:

Storing a jack, a tire or other equipment in thepassenger compartment of the vehicle couldcause injury. In a sudden stop or collision, looseequipment could strike someone. Store all thesein the proper place.

Storing the flat tire in the compact spare tirecompartment. Place the tire in the compartment, thensecure the adapter and the wing nut. Place the cover andthe nut on top of the flat tire. Store the jack and thewrench in the foam tray.

A. Nut

B. Wing Nut

C. Extension (If Equipped)

D. Adapter

E. Wrench

F. Jack

G. Tool Tray

H. Flat Road Tire

5-27

Storing the Spare Tire and Tools

CAUTION:

Storing a jack, a tire or other equipment in thepassenger compartment of the vehicle couldcause injury. In a sudden stop or collision, looseequipment could strike someone. Store all thesein the proper place.

The compact spare is for temporary use only. Replacethe compact spare tire with a full-size tire as soon as youcan. See “Compact Spare Tire” in the Index. See thestorage instructions label to replace your compact spareinto your trunk properly.

A. Nut

B. Cover

C. Wing Nut

D. Adapter

E. Wrench

F. Jack

G. Spare Tire

5-28

Compact Spare TireAlthough the compact spare tire was fully inflated when your vehicle was new, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 kPa).

After installing the compact spare on your vehicle, youshould stop as soon as possible and make sure your sparetire is correctly inflated. The compact spare is made toperform well at speeds up to 65 mph (105 km/h) fordistances up to 3,000 miles (5 000 km), so you can finishyour trip and have your full-size tire repaired or replacedwhere you want. Of course, it’s best to replace your sparewith a full-size tire as soon as you can. Your spare will lastlonger and be in good shape in case you need it again.

NOTICE:

When the compact spare is installed, don’t takeyour vehicle through an automatic car wash withguide rails. The compact spare can get caught onthe rails. That can damage the tire and wheel,and maybe other parts of your vehicle.

Don’t use your compact spare on other vehicles.

And don’t mix your compact spare tire or wheel withother wheels or tires. They won’t fit. Keep your sparetire and its wheel together.

NOTICE:

Tire chains won’t fit your compact spare. Usingthem can damage your vehicle and can damagethe chains too. Don’t use tire chains on yourcompact spare.

5-29

If You’re Stuck: In Sand, Mud, Ice or SnowIn order to free your vehicle when it is stuck, you willneed to spin the wheels, but you don’t want to spin yourwheels too fast. The method known as “rocking” canhelp you get out when you’re stuck, but you must use caution.

CAUTION:

If you let your tires spin at high speed, they canexplode, and you or others could be injured. And,the transaxle or other parts of the vehicle canoverheat. That could cause an enginecompartment fire or other damage. When you’restuck, spin the wheels as little as possible. Don’tspin the wheels above 35 mph (55 km/h) as shownon the speedometer.

NOTICE:

Spinning your wheels can destroy parts of yourvehicle as well as the tires. If you spin the wheelstoo fast while shifting your transaxle back andforth, you can destroy your transaxle.

For information about using tire chains on your vehicle,see “Tire Chains” in the Index.

Rocking Your Vehicle To Get It OutFirst, turn your steering wheel left and right. That willclear the area around your front wheels. Then shift backand forth between REVERSE (R) and a forward gear (or with a manual transaxle, between FIRST (1) orSECOND (2) and REVERSE (R)), spinning the wheelsas little as possible. Release the accelerator pedal whileyou shift, and press lightly on the accelerator pedalwhen the transaxle is in gear. By slowly spinning yourwheels in the forward and reverse directions, you willcause a rocking motion that may free your vehicle. If that doesn’t get you out after a few tries, you mayneed to be towed out. If you do need to be towed out,see “Towing Your Vehicle” in the Index.

6-6-1

Section 6 Service and Appearance Care

Here you will find information about the care of your vehicle. This section begins with service and fuel information,and then it shows how to check important fluid and lubricant levels. There is also technical information about yourvehicle, and a part devoted to its appearance care.

6-2 Service6-3 Fuel6-5 Fuels in Foreign Countries6-5 Filling Your Tank6-7 Filling a Portable Fuel Container6-8 Checking Things Under the Hood6-12 Engine Oil6-18 Engine Air Cleaner/Filter6-19 Automatic Transaxle Fluid6-19 Manual Transaxle Fluid6-20 Engine Coolant6-24 Power Steering Fluid6-25 Windshield Washer Fluid6-26 Brakes

6-29 Battery6-30 Bulb Replacement6-34 Tires6-42 Appearance Care6-42 Cleaning the Inside of Your Vehicle6-44 Care of Safety Belts6-45 Cleaning the Outside of Your Vehicle6-48 Finish Damage6-49 GM Vehicle Care/Appearance Materials6-50 Vehicle Identification Number (VIN)6-51 Electrical System6-56 Replacement Bulbs6-57 Capacities and Specifications6-58 Normal Maintenance Replacement Parts

6-2

ServiceYour dealer knows your vehicle best and wants you tobe happy with it. We hope you’ll go to your dealer forall your service needs. You’ll get genuine GM parts andGM-trained and supported service people.

We hope you’ll want to keep your GM vehicle all GM.Genuine GM parts have one of these marks:

Doing Your Own Service WorkIf you want to do some of your own service work, you’llwant to use the proper service manual. It tells you muchmore about how to service your vehicle than this manualcan. To order the proper service manual, see “Serviceand Owner Publications” in the Index.

Your vehicle has an air bag system. Before attempting to do your own service work, see “Servicing Your Air Bag-Equipped Vehicle” in the Index.

You should keep a record with all parts receipts and list the mileage and the date of any service work youperform. See “Maintenance Record” in the Index.

6-3

CAUTION:

You can be injured and your vehicle could bedamaged if you try to do service work on avehicle without knowing enough about it.

� Be sure you have sufficient knowledge,experience, the proper replacement partsand tools before you attempt any vehiclemaintenance task.

� Be sure to use the proper nuts, bolts andother fasteners. “English” and “metric”fasteners can be easily confused. If you usethe wrong fasteners, parts can later breakor fall off. You could be hurt.

Adding Equipment to the Outside of Your VehicleThings you might add to the outside of your vehicle canaffect the airflow around it. This may cause wind noiseand affect windshield washer performance. Check withyour dealer before adding equipment to the outside ofyour vehicle.

FuelUse regular unleaded gasoline rated at 87 octane orhigher. It is recommended that the gasoline meetspecifications which have been developed by theAmerican Automobile Manufacturers Association(AAMA) and endorsed by the Canadian Motor Vehicle Manufacturers Association for better vehicleperformance and engine protection. Gasolines meetingthe AAMA specification could provide improveddriveability and emission control system performancecompared to other gasolines.

Be sure the posted octane is at least 87. If the octane isless than 87, you may get a heavy knocking noise whenyou drive. If it’s bad enough, it can damage your engine.

If you’re using fuel rated at 87 octane or higher and you hear heavy knocking, your engine needs service.But don’t worry if you hear a little pinging noise whenyou’re accelerating or driving up a hill. That’s normal,and you don’t have to buy a higher octane fuel to get rid of pinging. It’s the heavy, constant knock that meansyou have a problem.

6-4

If your vehicle is certified to meet California EmissionStandards (indicated on the underhood emission controllabel), it is designed to operate on fuels that meetCalifornia specifications. If such fuels are not availablein states adopting California emissions standards, yourvehicle will operate satisfactorily on fuels meetingfederal specifications, but emission control systemperformance may be affected. The malfunction indicatorlamp on your instrument panel may turn on and/or yourvehicle may fail a smog-check test. (See “MalfunctionIndicator Lamp” in the Index.) If this occurs, return to your authorized Pontiac dealer for diagnosis todetermine the cause of failure. In the event it isdetermined that the cause of the condition is the type offuels used, repairs may not be covered by your warranty.

Some gasolines that are not reformulated for lowemissions may contain an octane-enhancing additivecalled methylcyclopentadienyl manganese tricarbonyl(MMT); ask your service station operator whether or not the fuel contains MMT. General Motors does notrecommend the use of such gasolines. If fuels containingMMT are used, spark plug life may be reduced and youremission control system performance may be affected.The malfunction indicator lamp on your instrumentpanel may turn on. If this occurs, return to yourauthorized Pontiac dealer for service.

To provide cleaner air, all gasolines in the United Statesare now required to contain additives that will helpprevent deposits from forming in your engine and fuelsystem, allowing your emission control system tofunction properly. Therefore, you should not have to addanything to the fuel. In addition, gasolines containingoxygenates, such as ethers and ethanol, andreformulated gasolines may be available in your area tocontribute to clean air. General Motors recommends thatyou use these gasolines, particularly if they comply withthe specifications described earlier.

NOTICE:

Your vehicle was not designed for fuel thatcontains methanol. Don’t use it. It can corrodemetal parts in your fuel system and also damageplastic and rubber parts. That damage wouldn’tbe covered under your warranty.

6-5

Fuels in Foreign CountriesIf you plan on driving in another country outside theUnited States or Canada, the proper fuel may be hard tofind. Never use leaded gasoline or any other fuel notrecommended in the previous text on fuel. Costly repairscaused by use of improper fuel wouldn’t be covered byyour warranty.

To check on fuel availability, ask an auto club, orcontact a major oil company that does business in thecountry where you’ll be driving.

You can also write us at the following address foradvice. Just tell us where you’re going and give yourVehicle Identification Number (VIN).

General Motors Overseas Distribution Corporation1908 Colonel Sam DriveOshawa, Ontario L1H 8P7

Filling Your Tank

CAUTION:

Gasoline vapor is highly flammable. It burnsviolently, and that can cause very bad injuries.Don’t smoke if you’re near gasoline or refuelingyour vehicle. Keep sparks, flames and smokingmaterials away from gasoline.

6-6

While refueling, hang the cap inside the fuel door.

To remove the cap, turn it slowly to the left(counterclockwise). The cap has a spring in it; if you letgo of the cap too soon, it will spring back to the right.

CAUTION:

If you get gasoline on yourself and thensomething ignites it, you could be badly burned.Gasoline can spray out on you if you open thefuel filler cap too quickly. This spray can happenif your tank is nearly full, and is more likely inhot weather. Open the fuel filler cap slowly andwait for any “hiss” noise to stop. Then unscrewthe cap all the way.

Be careful not to spill gasoline. Clean gasoline frompainted surfaces as soon as possible. See “Cleaning theOutside of Your Vehicle” in the Index.

6-7

When you put the cap back on, turn it to the right(clockwise) until you hear a clicking sound. Make sureyou fully install the cap. The diagnostic system candetermine if the fuel cap has been left off or improperlyinstalled. This would allow fuel to evaporate into theatmosphere. See “Malfunction Indicator Lamp” in the Index.

NOTICE:

If you need a new cap, be sure to get the righttype. Your dealer can get one for you. If you getthe wrong type, it may not fit properly. This maycause your malfunction indicator lamp to lightand your fuel tank and emissions system may bedamaged. See “Malfunction Indicator Lamp” inthe Index.

Filling a Portable Fuel Container

CAUTION:

Never fill a portable fuel container while it is inyour vehicle. Static electricity discharge from thecontainer can ignite the gasoline vapor. You canbe badly burned and your vehicle damaged if thisoccurs. To help avoid injury to you and others:

� Dispense gasoline only into approved containers.

� Do not fill a container while it is inside avehicle, in a vehicle’s trunk, pickup bed oron any surface other than the ground.

� Bring the fill nozzle in contact with theinside of the fill opening before operatingthe nozzle. Contact should be maintaineduntil the filling is complete.

� Don’t smoke while pumping gasoline.

6-8

Checking Things Under the Hood

CAUTION:

An electric fan under the hood can start up andinjure you even when the engine is not running.Keep hands, clothing and tools away from anyunderhood electric fan.

CAUTION:

Things that burn can get on hot engine parts andstart a fire. These include liquids like gasoline,oil, coolant, brake fluid, windshield washer andother fluids, and plastic or rubber. You or otherscould be burned. Be careful not to drop or spillthings that will burn onto a hot engine.

Hood ReleaseThe following sections tell you how to check fluids,lubricants and important parts under the hood.

To open the hood, first pull the handle inside the vehicle.

6-9

Then go to the front of the vehicle and move thesecondary hood release handle to the right.

Lift the hood, release the hood prop rod from its retainerand put the hood prop into the slot in the hood.

Before closing the hood, be sure all the filler caps are onproperly. Then lift the hood to relieve pressure on thehood prop. Remove the hood prop from the slot in thehood and return the prop to its retainer. Then just let thehood down and close it firmly.

6-10

2.4L L4 (CODE T) EngineWhen you open the hood, you’ll see:

A. Engine Coolant Surge TankB. Engine Oil Fill CapC. Engine Oil Dipstick

D. Power Steering Fluid ReservoirE. Brake Fluid ReservoirF. Engine Air Cleaner/Filter

G. BatteryH. Windshield Washer

Fluid Reservoir

6-11

3400 V6 (CODE E) EngineWhen you open the hood, you’ll see:

A. Engine Coolant Surge TankB. Power Steering Fluid ReservoirC. Engine Oil Fill Cap

D. Engine Oil DipstickE. Brake Fluid ReservoirF. Engine Air Cleaner/Filter

G. BatteryH. Windshield Washer

Fluid Reservoir

6-12

Engine Oil

3400 V6 Engine Only

If the LOW OIL light appears on the instrument panel, itmeans you need to check your engine oil level rightaway. For more information, see LOW OIL light in the Index.

You should check your engine oil level regularly; this isan added reminder.

Checking Engine OilIt’s a good idea to check your engine oil every time youget fuel. In order to get an accurate reading, the oil mustbe warm and the vehicle must be on level ground.

2.4L L4 Engine

6-13

3400 V6 Engine

The engine oil dipstick handle is yellow. The dipstick onthe 2.4L L4 engine is located at the rear of the engine.The dipstick on the 3400 V6 engine is located on thefront of the engine, behind the fan.

Turn off the engine and give the oil several minutes todrain back into the oil pan. If you don’t, the oil dipstickmight not show the actual level.

Pull out the dipstick and clean it with a paper towel orcloth, then push it back in all the way. Remove it again,keeping the tip down, and check the level.

3400 V6 Engine Shown2.4L L4 Engine Similar

6-14

When to Add Engine OilIf the oil is at or below the ADD line, then you’ll needto add at least one quart of oil. But you must use theright kind. This part explains what kind of oil to use. Forcrankcase capacity, see “Capacities and Specifications”in the Index.

NOTICE:

Don’t add too much oil. If your engine has somuch oil that the oil level gets above the uppermark that shows the proper operating range,your engine could be damaged. 2.4L L4 Engine

The 2.4L L4 engine oil fill cap is located on thepassenger’s side of the engine compartment on the engine.

6-15

3400 V6 Engine

The 3400 V6 engine oil fill cap is on the front of theengine, behind the radiator.

Be sure to fill it enough to put the level somewhere inthe proper operating range. Push the dipstick all the wayback in when you’re through.

What Kind of Engine Oil to UseOils recommended for your vehicle can be identified bylooking for the starburst symbol.

This symbol indicates that the oil has been certified bythe American Petroleum Institute (API). Do not use anyoil which does not carry this starburst symbol.

If you change your own oil,be sure you use oil that hasthe starburst symbol on thefront of the oil container. If you have your oilchanged for you, be sure the oil put into your engineis American PetroleumInstitute certified forgasoline engines.

You should also use the proper viscosity oil for yourvehicle, as shown in the following chart:

6-16

As shown in the chart, SAE 5W-30 is best for yourvehicle. However, you can use SAE 10W-30 if it’s goingto be 0�F (-18�C) or above. These numbers on an oilcontainer show its viscosity, or thickness. Do not useother viscosity oils, such as SAE 20W-50.

NOTICE:

Use only engine oil with the American PetroleumInstitute Certified For Gasoline Enginesstarburst symbol. Failure to use therecommended oil can result in engine damage notcovered by your warranty.

GM Goodwrench� oil meets all the requirements foryour vehicle.

If you are in an area where the temperature falls below-20�F (-29�C), consider using either an SAE 5W-30synthetic oil or an SAE 0W-30 oil. Both will provideeasier cold starting and better protection for your engineat extremely low temperatures.

6-17

Engine Oil AdditivesDon’t add anything to your oil. The recommended oilswith the starburst symbol are all you will need for goodperformance and engine protection.

When to Change Engine OilYour vehicle has a computer that lets you know when tochange your engine oil. This is not based on mileage, buton engine revolutions and engine operating temperature.When the computer has calculated that the oil needschanging, the GM Oil Life System� will indicate that achange is necessary. The mileage between oil and filterchanges will vary depending on how you drive yourvehicle -- usually between 3,000 miles (5 000 km) and7,500 miles (12 500 km) since your last oil and filterchange. Under severe conditions, the system may come onbefore 3,000 miles (5 000 km). Never drive your vehiclemore than 7,500 miles (12 500 km) or 12 months(whichever occurs first) without an oil change.

The system won’t detect dust in the oil. So, if you drive ina dusty area, be sure to change your oil and filter every3,000 miles (5 000 km) or sooner. Remember to reset theCHANGE OIL light whenever the oil is changed.

How to Reset the Change Oil Light

After changing the engine oil, the system must be reset.With the ignition key to ON (engine not running), pushthe RESET button located in the driver’s side instrumentpanel fuse block. The CHANGE OIL light will start toflash, press and hold the RESET button again. The resetis complete when you hear the chimes and theCHANGE OIL light goes out.

What to Do with Used OilDid you know that used engine oil contains certainelements that may be unhealthy for your skin and couldeven cause cancer? Don’t let used oil stay on your skinfor very long. Clean your skin and nails with soap andwater, or a good hand cleaner. Wash or properly throwaway clothing or rags containing used engine oil. (See the manufacturer’s warnings about the use anddisposal of oil products.)

Used oil can be a real threat to the environment. If youchange your own oil, be sure to drain all free-flowing oilfrom the filter before disposal. Don’t ever dispose of oil by putting it in the trash, pouring it on the ground, intosewers, or into streams or bodies of water. Instead, recycleit by taking it to a place that collects used oil. If you havea problem properly disposing of your used oil, ask yourdealer, a service station or a local recycling center for help.

6-18

Engine Air Cleaner/Filter

The air cleaner is located on the driver’s side of theengine compartment.

To check or replace the air filter:

1. Remove the screws that hold the cover on.

2. Lift off the cover.

3. Reinstall the air cleaner filter and replace the cover tightly.

Refer to the Maintenance Schedule to determine when toreplace the air filter.

See “Scheduled Maintenance Services” in the Index.

CAUTION:

Operating the engine with the air cleaner/filteroff can cause you or others to be burned. The aircleaner not only cleans the air, it stops flame ifthe engine backfires. If it isn’t there, and theengine backfires, you could be burned. Don’tdrive with it off, and be careful working on theengine with the air cleaner/filter off.

NOTICE:

If the air cleaner/filter is off, a backfire can causea damaging engine fire. And, dirt can easily get into your engine, which will damage it. Always have the air cleaner/filter in place when you’re driving.

6-19

Automatic Transaxle FluidIt is not necessary to check the transaxle fluid level. A transaxle fluid leak is the only reason for fluid loss. If a leak occurs, take the vehicle to the dealershipservice department and have it repaired as soon aspossible. You may also have your fluid level checked by your dealer or service center when you have your oil changed.

Change both the fluid and filter every 50,000 miles (83 000 km) if the vehicle is mainly driven under one ormore of these conditions:

� In heavy city traffic where the outside temperatureregularly reaches 90�F (32�C) or higher.

� In hilly or mountainous terrain.

� When doing frequent trailer towing.

� Uses such as found in taxi, police or delivery service.

If you do not use your vehicle under any of theseconditions, the fluid and filter do not require changing.

NOTICE:

We recommend you use only fluid labeledDEXRON�-III, because fluid with that label ismade especially for your automatic transaxle.Damage caused by fluid other thanDEXRON�-III is not covered by your newvehicle warranty.

Manual Transaxle FluidIt is not necessary to check the transaxle fluid level. A transaxle fluid leak is the only reason for fluid loss. If a leak occurs, take the vehicle to the dealershipservice department and have it repaired as soon aspossible. You may also have your fluid level checked by your dealer or service center when you have your oil changed.

6-20

Hydraulic ClutchThe hydraulic clutch linkage in your vehicle isself-adjusting. The clutch master cylinder reservoir isfilled with hydraulic clutch fluid.

It is not necessary to regularly check clutch fluid unlessyou suspect there is a leak in the system. Adding fluidwon’t correct a leak.

A fluid loss in this system could indicate a problem.Have the system inspected and repaired.

When to Check and What to Use

Refer to the MaintenanceSchedule to determine howoften you should check thefluid level in your clutchmaster cylinder reservoirand for the proper fluid. See “Owner Checks and Services” and“Recommended Fluids andLubricants” in the Index.

How to Check and Add FluidYou do not need to check the fluid level unless yoususpect a clutch problem. To check the fluid level, takethe cap off. If the fluid reaches the top of the reservoir,the fluid level is correct. It isn’t a good idea to top offyour clutch fluid. Adding fluid won’t correct a leak. A fluid loss in this system could indicate a problem.Have the system inspected and repaired.

Engine CoolantThe cooling system in your vehicle is filled withDEX-COOL� engine coolant. This coolant is designedto remain in your vehicle for 5 years or 150,000 miles(240 000 km), whichever occurs first, if you add onlyDEX-COOL� extended life coolant.

The following explains your cooling system and how toadd coolant when it is low. If you have a problem withengine overheating, see “Engine Overheating” in the Index.

6-21

A 50/50 mixture of clean, drinkable water andDEX-COOL� coolant will:

� Give freezing protection down to -34�F (-37�C).

� Give boiling protection up to 265�F (129�C).

� Protect against rust and corrosion.

� Help keep the proper engine temperature.

� Let the warning lights and gages work as they should.

NOTICE:

When adding coolant, it is important that you use only DEX-COOL� (silicate-free) coolant.If coolant other than DEX-COOL is added to the system, premature engine, heater core orradiator corrosion may result. In addition, theengine coolant will require change sooner -- at30,000 miles (50 000 km) or 24 months,whichever occurs first. Damage caused by the use of coolant other than DEX-COOL� is notcovered by your new vehicle warranty.

What to UseUse a mixture of one-half clean, drinkable water andone-half DEX-COOL� coolant which won’t damagealuminum parts. If you use this coolant mixture, youdon’t need to add anything else.

CAUTION:

Adding only plain water to your cooling systemcan be dangerous. Plain water, or some otherliquid like alcohol, can boil before the propercoolant mixture will. Your vehicle’s coolantwarning system is set for the proper coolantmixture. With plain water or the wrong mixture,your engine could get too hot but you wouldn’tget the overheat warning. Your engine couldcatch fire and you or others could be burned. Use a 50/50 mixture of clean, drinkable waterand DEX-COOL� coolant.

6-22

NOTICE:

If you use an improper coolant mixture, yourengine could overheat and be badly damaged.The repair cost wouldn’t be covered by yourwarranty. Too much water in the mixture canfreeze and crack the engine, radiator, heater coreand other parts.

If you have to add coolant more than four times a year,have your dealer check your cooling system.

NOTICE:

If you use the proper coolant, you don’t have toadd extra inhibitors or additives which claim toimprove the system. These can be harmful.

Checking Coolant

The coolant surge tank is located on the passenger’s sideof the engine compartment.

6-23

CAUTION:

Turning the surge tank pressure cap when theengine and radiator are hot can allow steam andscalding liquids to blow out and burn you badly.Never turn the surge tank pressure cap -- even alittle -- when the engine and radiator are hot.

The vehicle must be on a level surface. When yourengine is cold, the coolant level should be at the FULL COLD mark, or a little higher.

If the LOW COOLANTlight comes on and stays on,it means you’re low onengine coolant.

See “Low Coolant Warning Light” in the Index.

Adding Coolant

If you need more coolant, add the proper DEX-COOL�

coolant mixture at the surge tank, but only when theengine is cool.

CAUTION:

You can be burned if you spill coolant on hotengine parts. Coolant contains ethylene glycol,and it will burn if the engine parts are hotenough. Don’t spill coolant on a hot engine.

When replacing the pressure cap, make sure it is hand-tight.

6-24

Power Steering Fluid

When to Check Power Steering FluidIt is not necessary to regularly check power steeringfluid unless you suspect there is a leak in the system oryou hear an unusual noise. A fluid loss in this systemcould indicate a problem. Have the system inspected and repaired.

How to Check Power Steering FluidTurn the key off, let the engine compartment cool down,wipe the cap and the top of the reservoir clean, thenunscrew the cap and wipe the dipstick with a clean rag.Replace the cap and completely tighten it. Then removethe cap again and look at the fluid level on the dipstick.

The level should be at the FULL COLD mark. Ifnecessary, add only enough fluid to bring the level up tothe mark.

What to UseTo determine what kind of fluid to use, see“Recommended Fluids and Lubricants” in the Index.Always use the proper fluid. Failure to use the properfluid can cause leaks and damage hoses and seals.

6-25

Windshield Washer FluidWhat to UseWhen you need windshield washer fluid, be sure to readthe manufacturer’s instructions before use. If you will beoperating your vehicle in an area where the temperaturemay fall below freezing, use a fluid that has sufficientprotection against freezing.

Adding Washer Fluid

Open the cap labeledWASHER FLUID ONLY.Add washer fluid until thetank is full.

NOTICE:

� When using concentrated washer fluid,follow the manufacturer’s instructions foradding water.

� Don’t mix water with ready-to-use washerfluid. Water can cause the solution to freezeand damage your washer fluid tank andother parts of the washer system. Also,water doesn’t clean as well as washer fluid.

� Fill your washer fluid tank onlythree-quarters full when it’s very cold. This allows for expansion if freezing occurs,which could damage the tank if it iscompletely full.

� Don’t use engine coolant (antifreeze) inyour windshield washer. It can damageyour washer system and paint.

6-26

BrakesBrake Fluid

Your brake master cylinder reservoir is on the driver’sside of the engine compartment. It is filled with DOT-3brake fluid.

There are only two reasons why the brake fluid level in thereservoir might go down. The first is that the brake fluidgoes down to an acceptable level during normal brakelining wear. When new linings are put in, the fluid levelgoes back up. The other reason is that fluid is leaking outof the brake system. If it is, you should have your brakesystem fixed, since a leak means that sooner or later yourbrakes won’t work well, or won’t work at all.

So, it isn’t a good idea to “top off” your brake fluid.Adding brake fluid won’t correct a leak. If you add fluidwhen your linings are worn, then you’ll have too muchfluid when you get new brake linings. You should add(or remove) brake fluid, as necessary, only when work isdone on the brake hydraulic system.

CAUTION:

If you have too much brake fluid, it can spill on theengine. The fluid will burn if the engine is hotenough. You or others could be burned, and yourvehicle could be damaged. Add brake fluid onlywhen work is done on the brake hydraulic system.

6-27

United States Canada

When your brake fluid falls to a low level, your brakewarning light will come on. See “Brake System WarningLight” in the Index.

What to Add

When you do need brake fluid, use only DOT-3 brakefluid. Use new brake fluid from a sealed container only.Refer to “Recommended Fluids and Lubricants” in theMaintenance Schedule.

Always clean the brake fluid reservoir cap and the areaaround the cap before removing it. This will help keepdirt from entering the reservoir.

CAUTION:

With the wrong kind of fluid in your brakesystem, your brakes may not work well, or theymay not even work at all. This could cause acrash. Always use the proper brake fluid.

NOTICE:

� Using the wrong fluid can badly damagebrake system parts. For example, just a fewdrops of mineral-based oil, such as engineoil, in your brake system can damage brakesystem parts so badly that they’ll have to bereplaced. Don’t let someone put in thewrong kind of fluid.

� If you spill brake fluid on your vehicle’s painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on your vehicle. If you do, wash it off immediately.See “Appearance Care” in the Index.

6-28

Brake WearThe GT Series has four-wheel disc brakes and the SESeries has front disc brakes and rear drum brakes.

Disc brake pads have built-in wear indicators that make ahigh-pitched warning sound when the brake pads are wornand new pads are needed. The sound may come and go orbe heard all the time your vehicle is moving (except whenyou are pushing on the brake pedal firmly).

CAUTION:

The brake wear warning sound means that soonyour brakes won’t work well. That could lead toan accident. When you hear the brake wearwarning sound, have your vehicle serviced.

NOTICE:

Continuing to drive with worn -out brake padscould result in costly brake repair.

Some driving conditions or climates may cause a brakesqueal when the brakes are first applied or lightlyapplied. This does not mean something is wrong withyour brakes.

Properly torqued wheel nuts are necessary to helpprevent brake pulsation. When tires are rotated, inspectbrake pads for wear and evenly torque wheel nuts in theproper sequence to GM specifications.

If you have rear drum brakes, they don’t have wearindicators, but if you ever hear a rear brake rubbingnoise, have the rear brake linings inspected immediately.Also, the rear brake drums should be removed andinspected each time the tires are removed for rotation orchanging. When you have the front brake pads replaced,have the rear brakes inspected, too.

Brake linings should always be replaced as completeaxle sets.

See “Brake System Inspection” in Section 7 of this manualunder Part C “Periodic Maintenance Inspections.”

Brake Pedal TravelSee your dealer if the brake pedal does not return tonormal height, or if there is a rapid increase in pedaltravel. This could be a sign of brake trouble.

6-29

Brake AdjustmentEvery time you make a moderate brake stop, your discbrakes adjust for wear. If you rarely make a moderate orheavier stop, then your brakes might not adjust correctly.If you drive in that way, then -- very carefully -- make a few moderate brake stops about every 1,000 miles (1 600 km), so your brakes will adjust properly.

Replacing Brake System PartsThe braking system on a vehicle is complex. Its manyparts have to be of top quality and work well together ifthe vehicle is to have really good braking. Your vehiclewas designed and tested with top-quality GM brakeparts. When you replace parts of your braking system -- for example, when your brake linings weardown and you have to have new ones put in -- be sureyou get new approved GM replacement parts. If youdon’t, your brakes may no longer work properly. Forexample, if someone puts in brake linings that are wrongfor your vehicle, the balance between your front andrear brakes can change -- for the worse. The brakingperformance you’ve come to expect can change in manyother ways if someone puts in the wrong replacementbrake parts.

BatteryYour new vehicle comes with a maintenance freeACDelco� battery. When it’s time for a new battery, getone that has the replacement number shown on the originalbattery’s label. We recommend an ACDelco battery.

Vehicle StorageIf you’re not going to drive your vehicle for 25 days or more,remove the black, negative (-) cable from the battery. This will help keep your battery from running down.

CAUTION:

Batteries have acid that can burn you and gasthat can explode. You can be badly hurt if youaren’t careful. See “Jump Starting” in the Indexfor tips on working around a battery withoutgetting hurt.

Contact your dealer to learn how to prepare your vehiclefor longer storage periods.

Also, for your audio system, see “Theft-DeterrentFeature” in the Index.

6-30

Bulb ReplacementThis section describes bulb changing procedures forsome of your interior and exterior lamps. For bulb sizes,see “Replacement Bulbs” in the Index. For any bulbs notlisted in this section, contact your service department.

Halogen Bulbs

CAUTION:

Halogen bulbs have pressurized gas inside andcan burst if you drop or scratch the bulb. You orothers could be injured. Be sure to read andfollow the instructions on the bulb package.

Headlamps

For the type of bulb, see “Replacement Bulbs” in the Index.

6-31

1. Remove the fasteners and the splash shield. 2. Lift the two speed clips.

6-32

3. Lift the headlamp assembly forward, out of themounting bracket.

4. Twist the bulb assembly retainer counterclockwiseone-sixth of a turn and pull out the bulb assembly.

5. Unclip the bulb assembly from the wiring harness.

6. Reverse Steps 1 through 4 to replace the bulbassembly and headlamp housing.

Front Turn Signal and Parking Lamp Bulb Replacement1. Remove the headlamp assembly. Refer to the

removal procedure earlier in this section.

2. Twist the bulb assembly retainer and pull out the bulb.

3. Unclip the bulb assembly from the wiring harness.

4. Reverse Steps 1 through 2 to replace the bulbassembly. Be sure to properly align the bulb with thelocating feature in the assembly.

Center High-Mounted Stoplamp1. Open the trunk lid and locate the center

high-mounted stoplamp on the inside of the lid.

2. Using a flat screwdriver, remove the screws holdingthe bulb assembly.

3. Use a Phillips screwdriver to remove the three screws.

4. Gently remove and replace the bulbs.

5. Reverse this procedure to reassemble the lamp.

6-33

Rear Turn Signal and Stop/Taillamp Bulb ReplacementFor the type of bulb, see “Replacement Bulbs” in the Index.

1. Disconnect the cargo net in the trunk.

2. Pull back the trunk trim.

3. Remove the four wing nut bolts which fasten thetaillamp lens to the vehicle.

4. Carefully remove the taillamp lens from the bodyand avoid scratching the paint or dropping it.

5. Press the five tabs to release the plate from the lamp.

6. To remove a bulb, gently pull the bulb out from the socket.

7. Reverse Steps 3 through 6 to reassemble the taillamp.

Windshield Wiper Blade Replacement

Windshield wiper blades should be inspected at leasttwice a year for wear or cracking. See “Wiper BladeCheck” in Section 7 of this manual under Part B “Owner Checks and Services” for more information.

6-34

Replacement blades come in different types and areremoved in different ways. Here’s how to remove thetype with a Shepherd’s Hook:

1. Pull the windshield wiper arm away from the windshield.

2. Push the release lever and slide the wiper assemblytoward the driver’s side of the vehicle.

3. Install a new blade by reversing Steps 1 and 2.

For the proper type and size, see “Capacities andSpecifications” in the Index.

TiresYour new vehicle comes with high-quality tires made bya leading tire manufacturer. If you ever have questionsabout your tire warranty and where to obtain service, seeyour Pontiac Warranty booklet for details.

CAUTION:

Poorly maintained and improperly used tires are dangerous.� Overloading your tires can cause

overheating as a result of too much friction.You could have an air-out and a seriousaccident. See “Loading Your Vehicle” in the Index.

� Underinflated tires pose the same danger asoverloaded tires. The resulting accidentcould cause serious injury. Check all tiresfrequently to maintain the recommendedpressure. Tire pressure should be checkedwhen your tires are cold.

� Overinflated tires are more likely to be cut, punctured or broken by a suddenimpact -- such as when you hit a pothole.Keep tires at the recommended pressure.

� Worn, old tires can cause accidents. If yourtread is badly worn, or if your tires havebeen damaged, replace them.

6-35

Inflation -- Tire PressureThe Tire-Loading Information label, which is on therear edge of the driver’s door, shows the correctinflation pressures for your tires when they’re cold.“Cold” means your vehicle has been sitting for at leastthree hours or driven no more than 1 mile (1.6 km).

NOTICE:

Don’t let anyone tell you that underinflation oroverinflation is all right. It’s not. If your tiresdon’t have enough air (underinflation), you canget the following:� Too much flexing� Too much heat� Tire overloading� Bad wear� Bad handling� Bad fuel economy.

NOTICE: (Continued)

NOTICE: (Continued)

If your tires have too much air (overinflation),you can get the following:� Unusual wear� Bad handling� Rough ride� Needless damage from road hazards.

When to Check

Check your tires once a month or more.

Don’t forget your compact spare tire. It should be at 60 psi (420 kPa).

How to Check

Use a good quality pocket-type gage to check tirepressure. You can’t tell if your tires are properly inflatedsimply by looking at them. Radial tires may lookproperly inflated even when they’re underinflated.

Be sure to put the valve caps back on the valve stems.They help prevent leaks by keeping out dirt and moisture.

6-36

Tire Inspection and RotationTires should be rotated every 6,000 to 8,000 miles (10 000 to 13 000 km). Any time you notice unusualwear, rotate your tires as soon as possible and checkwheel alignment. Also check for damaged tires orwheels. See “When It’s Time for New Tires” and“Wheel Replacement” later in this section for more information.

The purpose of regular rotation is to achieve more uniformwear for all tires on the vehicle. The first rotation is themost important. See “Scheduled Maintenance Services” inthe Index for scheduled rotation intervals.

When rotating your tires, always use the correct rotationpattern shown here.

Don’t include the compact spare tire in your tire rotation.

After the tires have been rotated, adjust the front andrear inflation pressures as shown on the Tire-LoadingInformation label. Make certain that all wheel nuts areproperly tightened. See “Wheel Nut Torque” in the Index.

CAUTION:

Rust or dirt on a wheel, or on the parts to whichit is fastened, can make wheel nuts become looseafter a time. The wheel could come off and causean accident. When you change a wheel, removeany rust or dirt from places where the wheelattaches to the vehicle. In an emergency, you canuse a cloth or a paper towel to do this; but besure to use a scraper or wire brush later, if you need to, to get all the rust or dirt off. (See “Changing a Flat Tire” in the Index.)

6-37

When It’s Time for New Tires

One way to tell when it’stime for new tires is tocheck the treadwearindicators, which willappear when your tires haveonly 1/16 inch (1.6 mm) orless of tread remaining.

You need a new tire if any of the following statementsare true:

� You can see the indicators at three or more placesaround the tire.

� You can see cord or fabric showing through the tire’s rubber.

� The tread or sidewall is cracked, cut or snagged deepenough to show cord or fabric.

� The tire has a bump, bulge or split.

� The tire has a puncture, cut or other damage thatcan’t be repaired well because of the size or locationof the damage.

Buying New TiresTo find out what kind and size of tires you need, look atthe Tire-Loading Information label.

The tires installed on your vehicle when it was new hada Tire Performance Criteria Specification (TPC Spec)number on each tire’s sidewall. When you get new tires,get ones with that same TPC Spec number. That wayyour vehicle will continue to have tires that are designedto give proper endurance, handling, speed rating,traction, ride and other things during normal service onyour vehicle. If your tires have an all-season treaddesign, the TPC number will be followed by an “MS”(for mud and snow).

If you ever replace your tires with those not having aTPC Spec number, make sure they are the same size,load range, speed rating and construction type (bias,bias-belted or radial) as your original tires.

6-38

CAUTION:

Mixing tires could cause you to lose control whiledriving. If you mix tires of different sizes or types(radial and bias-belted tires), the vehicle may nothandle properly, and you could have a crash.Using tires of different sizes may also causedamage to your vehicle. Be sure to use the samesize and type tires on all wheels.

It’s all right to drive with your compact spare,though. It was developed for use on your vehicle.

CAUTION:

If you use bias-ply tires on your vehicle, thewheel rim flanges could develop cracks aftermany miles of driving. A tire and/or wheel couldfail suddenly, causing a crash. Use only radial-plytires with the wheels on your vehicle.

Uniform Tire Quality GradingThe following information relates to the systemdeveloped by the United States National HighwayTraffic Safety Administration, which grades tires bytreadwear, traction and temperature performance. (This applies only to vehicles sold in the United States.)The grades are molded on the sidewalls of mostpassenger car tires. The Uniform Tire Quality Gradingsystem does not apply to deep tread, winter-type snowtires, space-saver or temporary use spare tires, tires withnominal rim diameters of 10 to 12 inches (25 to 30 cm),or to some limited-production tires.

While the tires available on General Motors passengercars and light trucks may vary with respect to thesegrades, they must also conform to Federal safetyrequirements and additional General Motors TirePerformance Criteria (TPC) standards.

6-39

Treadwear

The treadwear grade is a comparative rating based onthe wear rate of the tire when tested under controlledconditions on a specified government test course. Forexample, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tiregraded 100. The relative performance of tires dependsupon the actual conditions of their use, however, andmay depart significantly from the norm due to variationsin driving habits, service practices and differences inroad characteristics and climate.

Traction -- AA, A, B, C

The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability tostop on wet pavement as measured under controlledconditions on specified government test surfaces ofasphalt and concrete. A tire marked C may have poortraction performance. Warning: The traction gradeassigned to this tire is based on straight-ahead brakingtraction tests, and does not include acceleration,cornering, hydroplaning, or peak traction characteristics.

Temperature -- A, B, C

The temperature grades are A (the highest), B, and C,representing the tire’s resistance to the generation ofheat and its ability to dissipate heat when tested undercontrolled conditions on a specified indoor laboratorytest wheel. Sustained high temperature can cause thematerial of the tire to degenerate and reduce tire life, andexcessive temperature can lead to sudden tire failure.The grade C corresponds to a level of performancewhich all passenger car tires must meet under theFederal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performanceon the laboratory test wheel than the minimum requiredby law.

Warning: The temperature grade for this tire isestablished for a tire that is properly inflated and notoverloaded. Excessive speed, underinflation, orexcessive loading, either separately or in combination,can cause heat buildup and possible tire failure.

6-40

Wheel Alignment and Tire BalanceThe wheels on your vehicle were aligned and balancedcarefully at the factory to give you the longest tire lifeand best overall performance.

Scheduled wheel alignment and wheel balancing are not needed. However, if you notice unusual tire wear or your vehicle pulling one way or the other, the alignment may need to be reset. If you notice your vehicle vibrating when driving on a smooth road, your wheels may need to be rebalanced.

Wheel ReplacementReplace any wheel that is bent, cracked, or badly rustedor corroded. If wheel nuts keep coming loose, the wheel,wheel bolts and wheel nuts should be replaced. If thewheel leaks air, replace it (except some aluminumwheels, which can sometimes be repaired). See yourdealer if any of these conditions exist.

Your dealer will know the kind of wheel you need.

Each new wheel should have the same load-carryingcapacity, diameter, width, offset and be mounted thesame way as the one it replaces.

If you need to replace any of your wheels, wheel boltsor wheel nuts, replace them only with new GM originalequipment parts. This way, you will be sure to have theright wheel, wheel bolts and wheel nuts for your vehicle.

CAUTION:

Using the wrong replacement wheels, wheel boltsor wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of yourvehicle, make your tires lose air and make you losecontrol. You could have a collision in which you orothers could be injured. Always use the correctwheel, wheel bolts and wheel nuts for replacement.

NOTICE:

The wrong wheel can also cause problems withbearing life, brake cooling, speedometer orodometer calibration, headlamp aim, bumperheight, vehicle ground clearance and tire or tirechain clearance to the body and chassis.

See “Changing a Flat Tire” in the Index for more information.

6-41

Used Replacement Wheels

CAUTION:

Putting a used wheel on your vehicle isdangerous. You can’t know how it’s been used orhow far it’s been driven. It could fail suddenlyand cause an accident. If you have to replace awheel, use a new GM original equipment wheel.

Tire Chains

NOTICE:

If your vehicle has P225/50R16 size tires, don’tuse tire chains. They can damage your vehiclebecause there’s not enough clearance.

Use another type of traction device only if itsmanufacturer recommends it for use on yourvehicle and tire size combination and road

NOTICE: (Continued)

NOTICE: (Continued)

conditions. Follow that manufacturer’sinstructions. To help avoid damage to yourvehicle, drive slowly, readjust or remove thedevice if it’s contacting your vehicle, and don’tspin your wheels.

If you do find traction devices that will fit, installthem on the front tires.If you have other tires, use tire chains only wherelegal and only when you must. Use only SAEClass “S” type chains that are the proper size for your tires. Install them on the front tires andtighten them as tightly as possible with the endssecurely fastened. Drive slowly and follow thechain manufacturer’s instructions. If you canhear the chains contacting your vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast orspinning the wheels with chains on will damage your vehicle.

6-42

Appearance CareRemember, cleaning products can be hazardous. Someare toxic. Others can burst into flame if you strike amatch or get them on a hot part of the vehicle. Some aredangerous if you breathe their fumes in a closed space.When you use anything from a container to clean yourvehicle, be sure to follow the manufacturer’s warningsand instructions. And always open your doors orwindows when you’re cleaning the inside.

Never use these to clean your vehicle:

� Gasoline

� Benzene

� Naphtha

� Carbon Tetrachloride

� Acetone

� Paint Thinner

� Turpentine

� Lacquer Thinner

� Nail Polish Remover

They can all be hazardous -- some more than others -- and they can all damage your vehicle, too.

Don’t use any of these unless this manual says you can.In many uses, these will damage your vehicle:

� Alcohol

� Laundry Soap

� Bleach

� Reducing Agents

Cleaning the Inside of Your VehicleUse a vacuum cleaner often to get rid of dust and loosedirt. Wipe vinyl, leather, plastic and painted surfaceswith a clean, damp cloth.

Cleaning of Fabric/CarpetYour dealer has two cleaners, Multi-Purpose InteriorCleaner and Capture Non-Solvent Dry Spot and SoilRemover for cleaning fabric and carpet. They will cleannormal spots and stains very well. You can getGM-approved cleaning products from your dealer. (See “Appearance Care and Materials” in the Index.)

Here are some cleaning tips:

� Always read the instructions on the cleaner label.

� Clean up stains as soon as you can -- before they set.

� Carefully scrape off any excess stain.

6-43

� Use a clean cloth or sponge, and change to a cleanarea often. A soft brush may be used if stains are stubborn.

� If a ring forms on fabric after spot cleaning, clean theentire area immediately or it will set.

Using Multi-Purpose Interior Cleaner on Fabric1. Vacuum and brush the area to remove any loose dirt.

2. Always clean a whole trim panel or section. Mask surrounding trim along stitch or welt lines.

3. Mix powdered cleaner following the directions onthe container label to form thick suds.

4. Use suds only and apply with a clean sponge. Don’t saturate the material and don’t rub it roughly.

5. As soon as you’ve cleaned the section, use a spongeto remove the suds.

6. Wipe cleaned area with a clean, damp towel or cloth.

7. Wipe with a clean cloth and let dry.

Special Fabric Cleaning ProblemsStains caused by such things as catsup, coffee (black),egg, fruit, fruit juice, milk, soft drinks, vomit, urine andblood can be removed as follows:

1. Carefully scrape off excess stain, then sponge thesoiled area with cool water.

2. If a stain remains, follow the multi-purpose interiorcleaner instructions described earlier.

3. If an odor lingers after cleaning vomit or urine, treat the area with a water/baking soda solution: 1 teaspoon (5 ml) of baking soda to 1 cup (250 ml)of lukewarm water.

4. Let dry.

Stains caused by candy, ice cream, mayonnaise, chilisauce and unknown stains can be removed as follows:

1. Carefully scrape off excess stain.

2. First, clean with cool water and allow to dry completely.

3. If a stain remains, follow instructions forMulti -Purpose Interior Cleaner.

6-44

Cleaning VinylUse warm water and a clean cloth.

� Rub with a clean, damp cloth to remove dirt. You may have to do it more than once.

� Things like tar, asphalt and shoe polish will stain if youdon’t get them off quickly. Use a clean cloth and avinyl/leather cleaner. See your dealer for this product.

Cleaning LeatherUse a soft cloth with lukewarm water and a mild soap orsaddle soap and wipe dry with a soft cloth. Then, let theleather dry naturally. Do not use heat to dry.

� For stubborn stains, use a leather cleaner. See yourdealer for this product.

� Never use oils, varnishes, solvent-based or abrasivecleaners, furniture polish or shoe polish on leather.

� Soiled or stained leather should be cleanedimmediately. If dirt is allowed to work into thefinish, it can harm the leather.

Cleaning the Top of the Instrument PanelUse only mild soap and water to clean the top surfacesof the instrument panel. Sprays containing silicones orwaxes may cause annoying reflections in the windshieldand even make it difficult to see through the windshieldunder certain conditions.

Cleaning Interior Plastic ComponentsUse only a mild soap and water solution on a soft clothor sponge. Commercial cleaners may affect the surface finish.

Care of Safety BeltsKeep belts clean and dry.

CAUTION:

Do not bleach or dye safety belts. If you do, itmay severely weaken them. In a crash, theymight not be able to provide adequate protection.Clean safety belts only with mild soap andlukewarm water.

6-45

Cleaning Glass SurfacesGlass should be cleaned often. GM Glass Cleaner or aliquid household glass cleaner will remove normaltobacco smoke and dust films on interior glass. (See “Appearance Care and Materials” in the Index.)

Don’t use abrasive cleaners on glass, because they maycause scratches. Avoid placing decals on the inside rearwindow, since they may have to be scraped off later. If abrasive cleaners are used on the inside of the rearwindow, an electric defogger element may be damaged.Any temporary license should not be attached across thedefogger grid.

Cleaning the Outside of theWindshield and Wiper BladesIf the windshield is not clear after using the windshieldwasher, or if the wiper blade chatters when running,wax, sap or other material may be on the blade or windshield.

Clean the outside of the windshield with GM WindshieldCleaner, Bon Ami� Powder (non-scratching glass cleaningpowder), GM Part No. 1050011. The windshield is clean ifbeads do not form when you rinse it with water.

Grime from the windshield will stick to the wiper bladesand affect their performance. Clean the blade by wipingvigorously with a cloth soaked in full-strength windshieldwasher solvent. Then rinse the blade with water.

Check the wiper blades and clean them as necessary;replace blades that look worn.

WeatherstripsSilicone grease on weatherstrips will make them lastlonger, seal better, and not stick or squeak. Apply siliconegrease with a clean cloth at least every six months. Duringvery cold, damp weather more frequent application may berequired. (See “Recommended Fluids and Lubricants” in the Index.)

Cleaning the Outside of Your VehicleThe paint finish on your vehicle provides beauty, depthof color, gloss retention and durability.

6-46

Washing Your VehicleThe best way to preserve your vehicle’s finish is to keep itclean by washing it often with lukewarm or cold water.

Don’t wash your vehicle in the direct rays of the sun.Use a car washing soap. Don’t use strong soaps orchemical detergents. Be sure to rinse the vehicle well,removing all soap residue completely. You can getGM-approved cleaning products from your dealer. (See“Appearance Care and Materials” in the Index.) Don’tuse cleaning agents that are petroleum based, or thatcontain acid or abrasives. All cleaning agents should beflushed promptly and not allowed to dry on the surface,or they could stain. Dry the finish with a soft, cleanchamois or an all-cotton towel to avoid surfacescratches and water spotting.

High pressure car washes may cause water to enter your vehicle.

Cleaning Exterior Lamps/LensesUse lukewarm or cold water, a soft cloth and a carwashing soap to clean exterior lamps and lenses. Follow instructions under “Washing Your Vehicle.”

Finish CareOccasional waxing or mild polishing of your vehicle byhand may be necessary to remove residue from the paintfinish. You can get GM-approved cleaning productsfrom your dealer. (See “Appearance Care and Materials”in the Index.)

Your vehicle has a “basecoat/clearcoat” paint finish. The clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish.

NOTICE:

Machine compounding or aggressive polishing ona basecoat/clearcoat paint finish may dull thefinish or leave swirl marks.

Foreign materials such as calcium chloride and othersalts, ice melting agents, road oil and tar, tree sap, birddroppings, chemicals from industrial chimneys, etc., candamage your vehicle’s finish if they remain on paintedsurfaces. Wash the vehicle as soon as possible. Ifnecessary, use non-abrasive cleaners that are markedsafe for painted surfaces to remove foreign matter.

6-47

Exterior painted surfaces are subject to aging, weatherand chemical fallout that can take their toll over a periodof years. You can help to keep the paint finish lookingnew by keeping your vehicle garaged or coveredwhenever possible.

Cleaning Aluminum Wheels (If Equipped)Keep your wheels clean using a soft clean cloth withmild soap and water. Rinse with clean water. Afterrinsing thoroughly, dry with a soft clean towel. A waxmay then be applied.

The surface of these wheels is similar to the paintedsurface of your vehicle. Don’t use strong soaps,chemicals, abrasive polishes, abrasive cleaners, cleanerswith acid or abrasive cleaning brushes on them becauseyou could damage the surface. Do not use chrome polishon aluminum wheels.

Don’t take your vehicle through an automatic car washthat has silicon carbide tire cleaning brushes. Thesebrushes can also damage the surface of these wheels.

Cleaning TiresTo clean your tires, use a stiff brush with a tire cleaner.

NOTICE:

When applying a tire dressing always take care towipe off any overspray or splash from all paintedsurfaces on the body or wheels of the vehicle.Petroleum-based products may damage the paintfinish and tires.

Sheet Metal DamageIf your vehicle is damaged and requires sheet metalrepair or replacement, make sure the body repair shopapplies anti-corrosion material to the parts repaired orreplaced to restore corrosion protection.

Original manufacturer replacement parts will providethe corrosion protection while maintaining the warranty.

6-48

Finish DamageAny stone chips, fractures or deep scratches in the finishshould be repaired right away. Bare metal will corrodequickly and may develop into a major repair expense.

Minor chips and scratches can be repaired with touch-upmaterials available from your dealer or other serviceoutlets. Larger areas of finish damage can be correctedin your dealer’s body and paint shop.

Underbody MaintenanceChemicals used for ice and snow removal and dust controlcan collect on the underbody. If these are not removed,accelerated corrosion (rust) can occur on the underbodyparts such as fuel lines, frame, floor pan and exhaustsystem even though they have corrosion protection.

At least every spring, flush these materials from theunderbody with plain water. Clean any areas where mudand other debris can collect. Dirt packed in closed areasof the frame should be loosened before being flushed.Your dealer or an underbody car washing system can dothis for you.

Chemical Paint SpottingSome weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on your vehicle. Thisdamage can take two forms: blotchy, ringlet-shapeddiscolorations, and small irregular dark spots etched intothe paint surface.

Although no defect in the paint job causes this, Pontiacwill repair, at no charge to the owner, the surfaces ofnew vehicles damaged by this fallout condition within12 months or 12,000 miles (20 000 km) of purchase,whichever occurs first.

6-49

GM Vehicle Care/Appearance Materials

PART NUMBER SIZE DESCRIPTION USAGE

994954 23 in. x 25 in. Polishing Cloth – Wax Treated Exterior polishing cloth

1050172 16 oz. (0.473 L) Tar and Road Oil Remover Removes tar, road oil and asphalt

1050173 16 oz. (0.473 L) Chrome Cleaner and Polish Use on chrome, stainless steel, nickel, copper and brass

1050174 16 oz. (0.473 L) White Sidewall Tire Cleaner Removes soil and black marks from whitewalls

1050214 32 oz. (0.946 L) Vinyl Cleaner Cleans vinyl tops, upholstery and convertible tops

1050427 23 oz. (0.680 L) Glass Cleaner Removes dirt, grime, smoke and fingerprints

1052918** 8 oz. (0.237 L) Armor All� Protectant Protects leather, wood, acrylics, Plexiglas�, plastic,rubber and vinyl

1052925 16 oz. (0.473 L) Multi-Purpose InteriorCleaner

Cleans carpets, seats, interior trim, door panels and floor mats

1052929 16 oz. (0.473 L) Wheel Cleaner Spray on and rinse with water

1052930 8 oz. (0.237 L) Capture Dry Spot Remover Attracts, absorbs and removes soils on fabric

12345721 2.5 sq. ft. Synthetic Chamois Shines vehicle without scratching

12345725 12 oz. (0.354 L) Silicone Tire Shine Spray on tire shine

12377964* 16 oz. (0.473 L) Finish Enhancer Removes dust, fingerprints and surface contaminants

12377966* 16 oz. (0.473 L) Cleaner Wax Removes light scratches and oxidation and protects finish

12377984* 16 oz. (0.473 L) Surface Cleaner Removes contaminants, blemishes and swirl marks

See your General Motors Parts Department for these products. * For exterior use only.See “Recommended Fluids and Lubricants” in the Index. **Not recommended for use on instrument panels.

6-50

Vehicle Identification Number (VIN)

This is the legal identifier for your vehicle. It appears ona plate in the front corner of the instrument panel, on thedriver’s side. You can see it if you look through thewindshield from outside your vehicle. The VIN alsoappears on the Vehicle Certification and Service Partslabels and the certificates of title and registration.

Engine IdentificationThe 8th character in your VIN is the engine code. Thiscode will help you identify your engine, specificationsand replacement parts.

Service Parts Identification LabelYou’ll find this label on the bottom of your spare tirecover. It’s very helpful if you ever need to order parts.On this label is:

� your VIN,

� the model designation,

� paint information and

� a list of all production options and special equipment.

Be sure that this label is not removed from the vehicle.

6-51

Electrical SystemAdd-On Electrical Equipment

NOTICE:

Don’t add anything electrical to your vehicle unlessyou check with your dealer first. Some electricalequipment can damage your vehicle and thedamage wouldn’t be covered by your warranty.Some add-on electrical equipment can keep othercomponents from working as they should.

Your vehicle has an air bag system. Before attempting toadd anything electrical to your vehicle, see “ServicingYour Air Bag-Equipped Vehicle” in the Index.

Windshield WipersThe windshield wiper motor is protected by a circuitbreaker and a fuse. If the motor overheats due to heavysnow, etc., the wiper will stop until the motor cools. Ifthe overload is caused by some electrical problem, haveit fixed.

Power WindowsA circuit breaker in the fuse panel protects the powerwindows. When the current load is too heavy, the circuitbreaker opens and closes, protecting the circuit until theproblem is fixed.

Fuses and Circuit BreakersThe wiring circuits in your vehicle are protected fromshort circuits by a combination of fuses, circuit breakersand fusible links. This greatly reduces the chance ofdamage caused by electrical problems.

Look at the silver-colored band inside the fuse. If theband is broken or melted, replace the fuse. Be sure toreplace a bad fuse with a new one of the identical size and rating.

There are three fuse blocks in your vehicle: twoinstrument panel fuse blocks and the enginecompartment fuse block.

There are four spare fuses located in the left instrumentpanel end cap for your use.

6-52

Instrument Panel Fuse Blocks

There are two fuse panels for your vehicle. One islocated on the driver’s side of the instrument panel andthe other is located on the passenger’s side.

Driver’s Side

Fuse UsageRADIO SW Steering Wheel Radio SwitchesRADIO ACC RadioWIPER Windshield Wiper Motor,

Washer PumpTRUNKREL/RFA/RADIO AMP

Trunk Release Relay/Motor, RKE, Audio Amplifier

TURN LPS Turn Signal LampsPWR MIRROR Power MirrorsAIR BAG Air BagsBFC BATT Body Computer (BFC)PCM ACC PCMDR LOCK Door Lock MotorsIPC/BFC ACC Cluster, Body Computer (BFC)STOP LPS StoplampsHAZARD LPS Hazard LampsIPC/HVACBATT

HVAC Head, Cluster, Data Link Connector

Circuit Breaker UsagePWR SEAT Power Seats

6-53

Passenger’s Side

Fuse Usage

INST LPS Interior Lamp Dimming

CRUISE SW LPS

Steering Wheel Cruise ControlSwitch Lamps

CRUISE SW Steering Wheel Cruise Control Switches

HVACBLOWER

HVAC Blower Motor

CRUISE Cruise Control

FOG LPS Fog Lamps

INT LPS Interior Courtesy Lamps

RADIO BATT Radio

SUNROOF Power Sunroof

Circuit Breaker Usage

PWR WNDW Power Windows

6-54

Engine Compartment Fuse Block

The engine compartment fuse block is located on thedriver’s side of the engine compartment, near the battery.

Fuse UsageMaxi-Fuses

1 Ignition Switch2 Left Electrical Center-Power Seats,

Power Mirrors, Door Locks, TrunkRelease, Audio Amplifier, RemoteLock Control

3 Left Electrical Center-Stoplamps,Hazard Lamps, Body FunctionControl Module, Cluster, ClimateControl System

6-55

Fuse Usage4 Right Electrical Center-Fog Lamps,

Radio, Body Function ControlModule, Interior Lamps

5 Ignition Switch6 A.I.R.7 Anti-Lock Brakes8 Cooling Fan # 1

Mini-Relays9 Rear Defog10 A.I.R.11 Anti-Lock Brakes12 Cooling Fan # 113 HVAC Blower (Climate Control)14 Cooling Fan # 215 Cooling Fan

Micro-Relays16 Air Conditioning Compressor17 Not Used18 Fuel Pump19 Automatic Light Control20 Automatic Light Control21 Horn22 Daytime Running Lamps

Fuse UsageMini-Fuses

23 - 32 Spare Fuse Holder33 Rear Defog34 Accessory Power Outlets,

Cigar Lighter35 Anti-Lock Brakes36 Anti-Lock Brakes, Variable

Effort Steering37 Air Conditioning Compressor,

Body Function Control Module38 Automatic Transaxle39 Powertrain Control Module40 Anti-Lock Brakes41 Ignition System42 Back-Up Lamps, Brake Transaxle

Shift Interlock43 Horn44 Powertrain Control Module45 Parking Lamps46 Climate Control System,

Air Conditioning

(Continued)

6-56

Fuse UsageMini-Fuses

47 Canister Vent Valve, ExhaustOxygen Sensors

48 Fuel Pump Injectors49 Generator50 Right Headlamp51 Left Headlamp52 Cooling Fan # 253 HVAC Blower (Climate Control )54 Not Used55 Cooling Fan #2 Ground56 Fuse Puller for Mini Fuses57 Not Used

Replacement BulbsExterior Lamps (Rear) Bulb

Back-Up Lamps 3156. . . . . . . . . . . . . . . . . . . . . . . Center High-Mounted Stoplamp 912. . . . . . . . . . . . Fascia Rear Cornering Lamps 912. . . . . . . . . . . . . . Turn Signal lamps 3156. . . . . . . . . . . . . . . . . . . . . . Stop/Taillamps 3157. . . . . . . . . . . . . . . . . . . . . . . .

Exterior Lamps (Front) BulbHalogen Headlamps 9007. . . . . . . . . . . . . . . . . . . . Parking/Turn Signal Lamps 3157NA. . . . . . . . . . . . Side Marker Lamps 194NA. . . . . . . . . . . . . . . . . . . . Fog Lamps 880X *. . . . . . . . . . . . . . . . . . . . . . . . .

Interior Lamps BulbDome (Base) 561 *. . . . . . . . . . . . . . . . . . . . . . . . . . Dome (Uplevel) 212-2 *. . . . . . . . . . . . . . . . . . . . . Glovebox 194 *. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

* For information on these bulbs, contact your Pontiacdealer service department.

6-57

Capacities and SpecificationsEngine Crankcase

2.4L L4 Engine 4.0 quarts (3.8 L). . . . . . . . . . . . . . 3400 V6 Engine 4.5 quarts (4.3 L). . . . . . . . . . . . .

Cooling System2.4L L4 Engine 11.3 quarts (10.7 L). . . . . . . . . . . . . 3400 V6 Engine 13.6 quarts (12.9 L). . . . . . . . . . .

Refrigerant, Air Conditioning See refrigerant. . . . . charge label under the hood.

Fuel Tank 14.3 gallons (54.1 L). . . . . . . . . . . . . . . . . Tire Pressures, Sizes See Tire-Loading. . . . . . . . . . .

Information label on the rear driver’sside passenger door.

Wheel Nut Torque 100 lb-ft (140 N·m). . . . . . . . . .

All capacities are approximate. When adding, be sure tofill to the appropriate level or as recommended in this manual.

See “Recommended Fluids and Lubricants” in the Index.

2.4L L4 Engine Specifications VIN Engine Code T. . . . . . . . . . . . . . . . . . . . . . . . . . . Type L4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Displacement 2.4 Liters. . . . . . . . . . . . . . . . . . . . . . . . Firing Order 1-3-4-2. . . . . . . . . . . . . . . . . . . . . . . . . . Horsepower 150. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3400 V6 Engine Specifications VIN Engine Code E. . . . . . . . . . . . . . . . . . . . . . . . . . . Type V6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Displacement 3.4 Liters. . . . . . . . . . . . . . . . . . . . . . . . Firing Order 1-2-3-4-5-6. . . . . . . . . . . . . . . . . . . . . . Horsepower-SE model 170. . . . . . . . . . . . . . . . . . . . . Horsepower-GT model 175. . . . . . . . . . . . . . . . . . . .

6-58

Normal Maintenance Replacement PartsAir Cleaner Element

2.4L L4 AC Type A-1279C. . . . . . . . . . . . . . . . . . . 3400 V6 AC Type A-1279C. . . . . . . . . . . . . . . . . . .

Engine Oil Filter2.4L L4 AC Type PF-44. . . . . . . . . . . . . . . . . . . . . . 3400 V6 AC Type PF-47. . . . . . . . . . . . . . . . . . . . . .

Spark Plugs2.4L L4 AC Type �41-963 . . . . . . . . . . . . . . . . . . . .

(Platinum Plug) Gap: 0.050 inch (1.27 mm)3400 V6 AC Type �41-940 . . . . . . . . . . . . . . . . . . . .

(Platinum Plug) Gap: 0.060 inch (1.52 mm)Windshield Wiper Blades (Shepherd’s Hook Type)

Passenger’s Side 17 inches (43 cm). . . . . . . . . . . . . Driver’s Side 22 inches (56 cm). . . . . . . . . . . . . . . .

Vehicle DimensionsLength 186.5 inches (474.2 cm). . . . . . . . . . . . . . . . .

Width 70.4 inches (178.7 cm). . . . . . . . . . . . . . . . . . .

Height 54.5 inches (138.4 cm). . . . . . . . . . . . . . . . . . .

Wheelbase 107.1 inches (271.9 cm). . . . . . . . . . . . . .

Front Tread 59.1 inches (150.0 cm). . . . . . . . . . . . . . .

Rear Tread 59.4 inches (150.7 cm). . . . . . . . . . . . . . .

7-7-1

Section 7 Maintenance Schedule

This section covers the maintenance required for your vehicle. Your vehicle needs these services to retain its safety,dependability and emission control performance.

7-2 Introduction7-3 How This Section is Organized7-4 Part A: Scheduled Maintenance Services7-14 Part B: Owner Checks and Services

7-19 Part C: Periodic Maintenance Inspections7-21 Part D: Recommended Fluids and Lubricants7-23 Part E: Maintenance Record

7-2

Have you purchased the GM Protection Plan? The Plansupplements your new vehicle warranties. See yourWarranty and Owner Assistance booklet, or your dealerfor details.

IntroductionYour Vehicle and the EnvironmentProper vehicle maintenance not only helps to keep yourvehicle in good working condition, but also helps theenvironment. All recommended maintenance proceduresare important. Improper vehicle maintenance can evenaffect the quality of the air we breathe. Improper fluidlevels or the wrong tire inflation can increase the levelof emissions from your vehicle. To help protect ourenvironment, and to keep your vehicle in goodcondition, please maintain your vehicle properly.

Maintenance RequirementsMaintenance intervals, checks, inspections andrecommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in goodworking condition. Any damage caused by failure tofollow recommended maintenance may not be coveredby warranty.

7-3

How This Section is OrganizedThis maintenance schedule is divided into five parts:

“Part A: Scheduled Maintenance Services” showswhat to have done and how often. Some of theseservices can be complex, so unless you are technicallyqualified and have the necessary equipment, you shouldlet your dealer’s service department or another qualifiedservice center do these jobs.

CAUTION:

Performing maintenance work on a vehicle canbe dangerous. In trying to do some jobs, you canbe seriously injured. Do your own maintenancework only if you have the required know-howand the proper tools and equipment for the job.If you have any doubt, have a qualifiedtechnician do the work.

If you want to get the service information, see “Service and Owner Publications” in the Index.

“Part B: Owner Checks and Services” tells you whatshould be checked and when. It also explains what youcan easily do to help keep your vehicle in good condition.

“Part C: Periodic Maintenance Inspections” explainsimportant inspections that your dealer’s service departmentor another qualified service center should perform.

“Part D: Recommended Fluids and Lubricants” listssome recommended products necessary to help keepyour vehicle properly maintained. These products, ortheir equivalents, should be used whether you do thework yourself or have it done.

“Part E: Maintenance Record” is a place for you torecord and keep track of the maintenance performed onyour vehicle. Keep your maintenance receipts. They maybe needed to qualify your vehicle for warranty repairs.

7-4

Part A: Scheduled Maintenance ServicesUsing Your Maintenance ScheduleWe at General Motors want to help you keep yourvehicle in good working condition. But we don’t knowexactly how you’ll drive it. You may drive very shortdistances only a few times a week. Or you may drivelong distances all the time in very hot, dusty weather.You may use your vehicle in making deliveries. Or you may drive it to work, to do errands or in many other ways.

Because of all the different ways people use theirvehicles, maintenance needs vary. You may need morefrequent checks and replacements. So please read thefollowing and note how you drive. If you have anyquestions on how to keep your vehicle in goodcondition, see your dealer.

This part tells you the maintenance services you shouldhave done and when you should schedule them. If yougo to your dealer for your service needs, you’ll knowthat GM-trained and supported service people willperform the work using genuine GM parts.

The proper fluids and lubricants to use are listed in Part D. Make sure whoever services your vehicle usesthese. All parts should be replaced and all necessaryrepairs done before you or anyone else drives the vehicle.

This schedule is for vehicles that:

� carry passengers and cargo within recommendedlimits. You will find these limits on your vehicle’sTire-Loading Information label. See “Loading Your Vehicle” in the Index.

� are driven on reasonable road surfaces within legaldriving limits.

� use the recommended fuel. See “Fuel” in the Index.

Scheduled Maintenance

7-5

The services shown in this schedule up to 100,000 miles(166 000 km) should be performed after 100,000 miles(166 000 km) at the same intervals. The services shownat 150,000 miles (240 000 km) should be performed atthe same interval after 150,000 miles (240 000 km).

See “Owner Checks and Services” and “PeriodicMaintenance Inspections” following.

Footnotes� The U.S. Environmental Protection Agency or theCalifornia Air Resources Board has determined that thefailure to perform this maintenance item will not nullifythe emission warranty or limit recall liability prior tothe completion of the vehicle’s useful life. We, however,urge that all recommended maintenance services beperformed at the indicated intervals and themaintenance be recorded.

+ A good time to check your brakes is during tirerotation. See “Brake System Inspection” under“Periodic Maintenance Inspections” in Part C of this schedule.

Scheduled Maintenance

7-6

Engine Oil Scheduled MaintenanceChange engine oil and filter as indicated by the GM Oil Life System� (or every 12 months,whichever occurs first). Reset the system. The systemwill show you when to change the oil -- usually between3,000 miles (5 000 km) and 7,500 miles (12 500 km) sinceyour last oil change. Under severe conditions, the indicatormay come on before 3,000 miles (5 000 km). Never driveyour vehicle more than 7,500 miles (12 500 km) or 12 months without an oil and filter change.

The system won’t detect dust in the oil. So if you drive ina dusty area, be sure to change your oil and filter every3,000 miles (5 000 km) or sooner if the CHANGE OILlight appears. Remember to reset the Oil Life Systemwhen the oil and filter have been changed. See “Oil LifeSystem” in the Index for information on resetting.

An Emission Control Service.

Scheduled Maintenance

7-7

Scheduled Maintenance

7-8

Scheduled Maintenance

7-9

7,500 Miles (12 500 km)� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

15,000 Miles (25 000 km)� Inspect engine air cleaner filter if you are driving in dusty conditions.

Replace filter if necessary. An Emission Control Service. (See footnote �.)

� Rotate tires. See “Tire Inspection and Rotation” in the Index for properrotation pattern and additional information. (See footnote +.)

22,500 Miles (37 500 km)� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

30,000 Miles (50 000 km)� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.) � Replace engine air cleaner filter.

An Emission Control Service.

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

Scheduled Maintenance

7-10

37,500 Miles (62 500 km)� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

45,000 Miles (75 000 km)� Inspect engine air cleaner filter if you are driving in dusty conditions.

Replace filter if necessary. An Emission Control Service. (See footnote �.)

� Rotate tires. See “Tire Inspection and Rotation” in the Index for properrotation pattern and additional information. (See footnote +.)

50,000 Miles (83 000 km)� Change automatic transaxle fluid and filter if the vehicle is mainly driven

under one or more of these conditions:– In heavy city traffic where the outside temperature regularly reaches

90�F (32�C) or higher.– In hilly or mountainous terrain.– When doing frequent trailer towing.– Uses such as found in taxi, police or delivery service.If you do not use your vehicle under any of these conditions, the fluid andfilter do not require changing.

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

Scheduled Maintenance

7-11

52,500 Miles (87 500 km)� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

60,000 Miles (100 000 km)� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.) � Inspect engine accessory drive belt.

An Emission Control Service. � Replace engine air cleaner filter.

An Emission Control Service.

67,500 Miles (112 500 km)� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

Scheduled Maintenance

7-12

75,000 Miles (125 000 km)� Inspect engine air cleaner filter if you are driving in dusty conditions.

Replace filter if necessary. An Emission Control Service. (See footnote �.)

� Rotate tires. See “Tire Inspection and Rotation” in the Index for properrotation pattern and additional information. (See footnote +.)

82,500 Miles (137 500 km)� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

90,000 Miles (150 000 km)� Replace engine air cleaner filter.

An Emission Control Service. � Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

97,500 Miles (162 500 km)� Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. (See footnote +.)

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

Scheduled Maintenance

7-13

100,000 Miles (166 000 km)� Inspect spark plug wires (except 2.4L Code T L4 engine).

An Emission Control Service. � Replace spark plugs.

An Emission Control Service.� Change automatic transaxle fluid and filter if the vehicle is mainly driven

under one or more of these conditions:– In heavy city traffic where the outside temperature regularly reaches

90�F (32�C) or higher.– In hilly or mountainous terrain.– When doing frequent trailer towing.– Uses such as found in taxi, police or delivery service.If you do not use your vehicle under any of these conditions, the fluid andfilter do not require changing.

150,000 Miles (240 000 km)� Drain, flush and refill cooling system (or every 60 months since last service,

whichever occurs first). See “Engine Coolant” in the Index for what to use.Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure testthe cooling system and pressure cap. An Emission Control Service.

ACTUAL SERVICED BY:MILEAGE

DATE

ACTUAL SERVICED BY:MILEAGE

DATE

7-14

Part B: Owner Checks and ServicesListed in this part are owner checks and services whichshould be performed at the intervals specified to helpensure the safety, dependability and emission controlperformance of your vehicle.

Be sure any necessary repairs are completed at once.Whenever any fluids or lubricants are added to yourvehicle, make sure they are the proper ones, as shown in Part D.

At Each Fuel FillIt is important for you or a service station attendant toperform these underhood checks at each fuel fill.

Engine Oil Level Check

Check the engine oil level and add the proper oil ifnecessary. See “Engine Oil” in the Index for further details.

Engine Coolant Level Check

Check the engine coolant level and add DEX-COOL�

coolant mixture if necessary. See “Engine Coolant” inthe Index for further details.

Windshield Washer Fluid Level Check

Check the windshield washer fluid level in thewindshield washer tank and add the proper fluid ifnecessary. See “Windshield Washer Fluid” in the Index for further details.

At Least Once a Month

Tire Inflation Check

Make sure tires are inflated to the correct pressures.Don’t forget to check your spare tire. See “Tires” in the Index for further details.

Cassette Deck Service

Clean cassette deck. Cleaning should be done every 50 hours of tape play. See “Audio Systems” in the Index for further details.

7-15

At Least Twice a Year

Restraint System Check

Make sure the safety belt reminder light and all yourbelts, buckles, latch plates, retractors and anchorages areworking properly. Look for any other loose or damagedsafety belt system parts. If you see anything that mightkeep a safety belt system from doing its job, have itrepaired. Have any torn or frayed safety belts replaced.

Also look for any opened or broken air bag coverings,and have them repaired or replaced. (The air bag systemdoes not need regular maintenance.)

Wiper Blade Check

Inspect wiper blades for wear or cracking. Replace bladeinserts that appear worn or damaged or that streak ormiss areas of the windshield. Also see “Wiper Blades,Cleaning” in the Index.

Weatherstrip Lubrication

Silicone grease on weatherstrips will make them lastlonger, seal better, and not stick or squeak. Applysilicone grease with a clean cloth. During very cold,damp weather more frequent application may berequired. (See “Recommended Fluids and Lubricants” in the Index.)

Manual Transaxle Check

It is not necessary to check the transaxle fluid level.Check for leaks. A fluid leak is the only reason for fluidloss. Have the system inspected and repaired if needed.

Automatic Transaxle Inspection

It is not necessary to check the transaxle fluid level. A transaxle fluid leak is the only reason for fluid loss.Check for leaks. If a leak occurs, take the vehicle toyour Pontiac dealership service department and have itrepaired as soon as possible.

Hydraulic Clutch System Check

Check the fluid level in the clutch reservoir. See“Hydraulic Clutch Fluid” in the Index. A fluid loss inthis system could indicate a problem. Have the systeminspected and repaired at once.

7-16

At Least Once a Year

Key Lock Cylinders Service

Lubricate the key lock cylinders with the lubricantspecified in Part D.

Body Lubrication Service

Lubricate all the door hinges and latches, includingthose for the hood and the trunk lid. Part D tells youwhat to use. More frequent lubrication may be requiredwhen exposed to a corrosive environment.

Starter Switch Check

CAUTION:

When you are doing this check, the vehicle couldmove suddenly. If it does, you or others could beinjured. Follow the steps below.

1. Before you start, be sure you have enough roomaround the vehicle.

2. Firmly apply both the parking brake (see “ParkingBrake” in the Index if necessary) and the regular brake.

NOTE: Do not use the accelerator pedal, and beready to turn off the engine immediately if it starts.

3. Try to start the engine in each gear. The startershould work only in PARK (P) or NEUTRAL (N). If the starter works in any other position, yourvehicle needs service.

7-17

Automatic Transaxle Shift Lock Control System Check

CAUTION:

When you are doing this check, the vehicle couldmove suddenly. If it does, you or others could beinjured. Follow the steps below.

1. Before you start, be sure you have enough roomaround the vehicle. It should be parked on a level surface.

2. Firmly apply the parking brake (see “Parking Brake”in the Index if necessary).

NOTE: Be ready to apply the regular brakeimmediately if the vehicle begins to move.

3. With the engine off, turn the key to the ON position,but don’t start the engine. Without applying theregular brake, try to move the shift lever out ofPARK (P) with normal effort. If the shift levermoves out of PARK (P), your vehicle needs service.

Ignition Transaxle Lock Check

While parked, and with the parking brake set, try to turnthe ignition key to OFF in each shift lever position.

With a manual transaxle, the key should turn to OFFonly when the shift lever is in reverse.

On all vehicles, the key should come out only in OFF.

7-18

Parking Brake and Automatic Transaxle PARK (P)Mechanism Check

CAUTION:

When you are doing this check, your vehiclecould begin to move. You or others could beinjured and property could be damaged. Makesure there is room in front of your vehicle in caseit begins to roll. Be ready to apply the regularbrake at once should the vehicle begin to move.

Park on a fairly steep hill, with the vehicle facingdownhill. Keeping your foot on the regular brake, set the parking brake.

� To check the parking brake’s holding ability: Withthe engine running and transaxle in NEUTRAL (N),slowly remove foot pressure from the regular brakepedal. Do this until the vehicle is held by the parkingbrake only.

� To check the PARK (P) mechanism’s holding ability:With the engine running, shift to PARK (P). Then releasethe parking brake followed by the regular brake.

Underbody Flushing Service

At least every spring, use plain water to flush anycorrosive materials from the underbody. Take care toclean thoroughly any areas where mud and other debriscan collect.

7-19

Part C: Periodic Maintenance InspectionsListed in this part are inspections and services whichshould be performed at least twice a year (for instance,each spring and fall). You should let your dealer’sservice department or other qualified service center do these jobs. Make sure any necessary repairs arecompleted at once.

Proper procedures to perform these services may befound in a service manual. See “Service and OwnerPublications” in the Index.

Steering, Suspension and Front Drive Axle Boot and Seal InspectionInspect the front and rear suspension and steeringsystem for damaged, loose or missing parts, signs ofwear or lack of lubrication. Inspect the power steeringlines and hoses for proper hook-up, binding, leaks,cracks, chafing, etc. Clean and then inspect the driveaxle boot seals for damage, tears or leakage. Replaceseals if necessary.

Exhaust System InspectionInspect the complete exhaust system. Inspect the bodynear the exhaust system. Look for broken, damaged,missing or out-of-position parts as well as open seams,holes, loose connections or other conditions which couldcause a heat build-up in the floor pan or could letexhaust fumes into the vehicle. See “Engine Exhaust” in the Index.

Engine Cooling System InspectionInspect the hoses and have them replaced if they arecracked, swollen or deteriorated. Inspect all pipes, fittingsand clamps; replace as needed. Clean the outside of theradiator and air conditioning condenser. To help ensureproper operation, a pressure test of the cooling system and pressure cap is recommended at least once a year.

7-20

Throttle System InspectionInspect the throttle system for interference or binding,and for damaged or missing parts. Replace parts asneeded. Replace any components that have high effortor excessive wear. Do not lubricate accelerator andcruise control cables.

Brake System Inspection (Except GT Series)Inspect the complete system. Inspect brake lines andhoses for proper hook-up, binding, leaks, cracks,chafing, etc. Inspect disc brake pads for wear and rotorsfor surface condition. Also inspect drum brake liningsfor wear and cracks. Inspect other brake parts, includingdrums, wheel cylinders, calipers, parking brake, etc. The parking brake is self-adjusting and no manualadjustment is required. You may need to have yourbrakes inspected more often if your driving habits orconditions result in frequent braking.

Brake System Inspection (GT Series Only)Inspect the complete system. Inspect brake lines andhoses for proper hook-up, binding, leaks, cracks,chafing, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect other brake parts,including calipers, parking brake, etc. You may need tohave your brakes inspected more often if your drivinghabits or conditions result in frequent braking.

7-21

Part D: Recommended Fluids and LubricantsNOTE: Fluids and lubricants identified below by name,part number or specification may be obtained from your dealer.

USAGE FLUID/LUBRICANT

Engine Oil Engine Oil with the AmericanPetroleum Institute Certified ForGasoline Engines starburst symbolof the proper viscosity. Todetermine the preferred viscosityfor your vehicle’s engine, see“Engine Oil” in the Index.

Engine Coolant 50/50 mixture of clean, drinkablewater and use only GMGoodwrench� DEX-COOL� orHavoline� DEX-COOL� Coolant.See “Engine Coolant” in the Index.

USAGE FLUID/LUBRICANT

Hydraulic Brake System

Delco Supreme 11� Brake Fluid(GM Part No. 12377967 orequivalent DOT-3 Brake Fluid).

WindshieldWasher Solvent

GM Optikleen� Washer Solvent(GM Part No. 1051515) or equivalent.

Hydraulic Clutch System

Hydraulic Clutch Fluid (GM Part No. 12345347 orequivalent DOT-3 Brake Fluid).

Power Steering System

GM Power Steering Fluid (GM Part No. 1052884 - 1 pint,1050017 - 1 quart, or equivalent).

ManualTransaxle

DEXRON�-III AutomaticTransmission Fluid.

7-22

USAGE FLUID/LUBRICANT

AutomaticTransaxle

DEXRON�-III AutomaticTransmission Fluid.

Key LockCylinders

Multi -Purpose Lubricant,Superlube� (GM Part No. 12346241 or equivalent).

Hood LatchAssembly,Secondary Latch,Pivots, SpringAnchor andRelease Pawl

Lubriplate� Lubricant Aerosol(GM Part No. 12346293 orequivalent) or lubricant meetingrequirements of NLGI # 2,Category LB or GC-LB.

USAGE FLUID/LUBRICANT

Hood and Door Hinges

Multi -Purpose Lubricant,Superlube� (GM Part No. 12346241 or equivalent).

WeatherstripConditioning

Dielectric Silicone Grease (GMPart No. 12345579 or equivalent).

7-23

Part E: Maintenance RecordAfter the scheduled services are performed, record thedate, odometer reading and who performed the servicein the boxes provided after the maintenance interval.

Any additional information from “Owner Checks andServices” or “Periodic Maintenance” can be added onthe following record pages. Also, you should retain allmaintenance receipts. Your owner information portfoliois a convenient place to store them.

Maintenance Record

DATEODOMETER

READING SERVICED BY MAINTENANCE PERFORMED

7-24

Maintenance Record

DATEODOMETER

READING SERVICED BY MAINTENANCE PERFORMED

8-8-1

Section 8 Customer Assistance Information

Here you will find out how to contact Pontiac if you need assistance. This section also tells you how to obtain servicepublications and how to report any safety defects.

8-2 Pontiac Cares8-3 What Makes Up Pontiac Cares?8-3 Customer Satisfaction Procedure8-5 Customer Assistance for Text Telephone

(TTY) Users8-5 Customer Assistance Offices8-7 GM Mobility Program for Persons

with Disabilities8-8 Pontiac Roadside Assistance Program8-9 Canadian Roadside Assistance

8-10 Courtesy Transportation8-11 Warranty Information8-12 Reporting Safety Defects to the United

States Government8-12 Reporting Safety Defects to the

Canadian Government8-13 Reporting Safety Defects to General Motors8-13 Ordering Owner Publications in Canada

8-2

Pontiac Cares

With PONTIAC CARES, you are never more than a phone call away from having your concern taken care of.

The PONTIAC CARES philosophy and elements aredesigned to make you realize that Pontiac recognizesyou as a valuable customer, appreciates your purchasedecision, and is dedicated to taking care of the mostimportant person ... YOU! PONTIAC CARES is: Avaluable feature that comes with every Pontiac, a featurethat offers a multitude of benefits that can give yousafety, security, comfort and convenience.

8-3

What Makes Up Pontiac Cares?� A 3 year/36,000 mile (60 000 km)

Bumper-to-Bumper Warranty

� Customer Assistance

� Roadside Assistance

� Courtesy Transportation

All of these elements combine to make your drivingexperience an enjoyable one and are discussed in greaterdetail in your owner’s manual. Pontiac is focusing onthe changing needs of our customers and is committedto giving you an exceptional level of customer carethroughout your ownership experience. Our goal is to create total customer enthusiasm in our product andour services and make you the most satisfied customerin the world.

Customer Satisfaction Procedure

8-4

Your satisfaction and goodwill are important to yourdealer and to Pontiac. Normally, any concerns with thesales transaction or the operation of your vehicle will beresolved by your dealer’s sales or service departments.Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur. If yourconcern has not been resolved to your satisfaction, thefollowing steps should be taken:

STEP ONE -- Discuss your concern with a member ofdealership management. Normally, concerns can bequickly resolved at that level. If the matter has alreadybeen reviewed with the sales, service or parts manager,contact the owner of the dealership or the general manager.

STEP TWO -- If after contacting a member of dealership management, it appears your concern cannot beresolved by the dealership without further help, contact the Pontiac Customer Assistance Center by calling1-800-762-2737. In Canada, contact GM of CanadaCustomer Communication Centre in Oshawa by calling1-800-263-3777 (English) or 1-800-263-7854 (French).

We encourage you to call the toll-free number in orderto give your inquiry prompt attention. Please have thefollowing information available to give the CustomerAssistance Representative:

� Vehicle Identification Number (This is availablefrom the vehicle registration or title, or the plate at the top left of the instrument panel and visiblethrough the windshield.)

� Dealership name and location

� Vehicle delivery date and present mileage

When contacting Pontiac, please remember that yourconcern will likely be resolved at a dealer’s facility. Thatis why we suggest you follow Step One first if you havea concern.

STEP THREE -- Both General Motors and your dealerare committed to making sure you are completelysatisfied with your new vehicle. However, if youcontinue to remain unsatisfied after following theprocedure outlined in Steps One and Two, file with theGM/BBB Auto Line Program to enforce any additionalrights you may have. Canadian owners refer to yourWarranty and Owner Assistance Information booklet for information on the Canadian Motor VehicleArbitration Plan (CAMVAP).

8-5

The BBB Auto Line Program is an out of court programadministered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs orthe interpretation of the New Vehicle Limited Warranty.Although you are required to resort to this informal disputeresolution program prior to filing any court action, use ofthe program is free of charge and your case will generallybe heard within 40 days. If you do not agree with thedecision given in your case, you may reject it and proceedwith any other venue for relief available to you.

You may contact the BBB using the toll-free telephonenumber or write them at the following address:

BBB Auto LineCouncil of Better Business Bureaus, Inc.4200 Wilson BoulevardSuite 800Arlington, VA 22203-1804

Telephone: 1-800-955-5100

This program is available in all 50 states and the Districtof Columbia. Eligibility is limited by vehicle age,mileage and other factors. General Motors reserves theright to change eligibility limitations and/or discontinueits participation in this program.

Customer Assistance for TextTelephone (TTY) UsersTo assist customers who are deaf, hard of hearing, orspeech-impaired and who use Text Telephones (TTYs),Pontiac has TTY equipment available at its CustomerAssistance Center. Any TTY user can communicate with Pontiac by dialing: 1-800-833-PONT (7668). (TTY users in Canada can dial 1-800-263-3830.)

Customer Assistance OfficesPontiac encourages customers to call the toll-free numberfor assistance. If a U.S. customer wishes to write toPontiac, the letter should be addressed to Pontiac’sCustomer Assistance Center.

United StatesPontiac-GMC Customer Assistance CenterP.O. Box 436008Pontiac, MI 48343-6008

1-800-762-2737 or 1-800-833-7668 (For Text Telephone devices (TTYs))Roadside Assistance: 1-800-ROADSIDE (762-3743)

8-6

CanadaGeneral Motors of Canada LimitedCustomer Communication Centre, 163-0051908 Colonel Sam DriveOshawa, Ontario L1H 8P7

1-800-263-3777 (English)1-800-263-7854 (French)1-800-263-3830 (For Text Telephone devices (TTYs))Roadside Assistance: 1-800-268-6800

All Overseas LocationsGMODC - Customer Communication Centre169-0071908 Colonel Sam DriveOshawa, Ontario L1H 8P7

Telephone: 905-644-4112Fax: 905-644-4866

Caribbean Numbers1-800-496-9992 (English) Puerto Rico1-800-496-9993 (Spanish) Puerto Rico1-800-751-4135 (English) Dominican Republic1-800-751-4136 (Spanish) Dominican Republic1-800-496-9994 U.S. Virgin Islands1-800-389-0009 Bahamas1-800-534-0122 Bermuda, Barbados, Antigua & B.V.I.

If toll free service is not available in the Caribbean, call Puerto Rico 1-787-763-1315.

8-7

GM Mobility Program for Personswith Disabilities

This program, available toqualified applicants, canreimburse you up to $1,000toward aftermarket driver or passenger adaptiveequipment you may requirefor your vehicle (handcontrols, wheelchair/scooterlifts, etc.).

This program can also provide you with free resourceinformation, such as area driver assessment centers andmobility equipment installers. The program is availablefor a limited period of time from the date of vehiclepurchase/lease. See your dealer for more details or callthe GM Mobility Assistance Center at 1-800-323-9935.Text telephone (TTY) users, call 1-800-833-9935.

GM of Canada also has a Mobility Program. Call1-800-GM-DRIVE (463-7483) for details. When calling from outside Canada, please dial 1-905-644-3063.All TTY users call 1-800-263-3830.

8-8

Pontiac Roadside Assistance Program

Security While You Travel1-800-ROADSIDE (1-800-762-3743)

As the proud owner of a new Pontiac vehicle, you areautomatically enrolled in the Pontiac Roadside

Assistance program. This value-added service isintended to provide you with peace of mind as you drive in the city or travel the open road.

Pontiac’s Roadside Assistance toll-free number isstaffed by a team of technically trained advisors, whoare available 24 hours a day, 365 days a year.

We take anxiety out of uncertain situations by providingminor repair information over the phone or makingarrangements to tow your vehicle to the nearest Pontiac dealer.

We will provide the following services for 3 years/36,000 miles (60 000 km), at no expense to you:

� Fuel delivery

� Keys locked in vehicle

� Tow to nearest dealership for warranty service

� Change a flat tire

� Jump starts

� Courtesy Transportation -- See CourtesyTransportation section for details

8-9

We have quick, easy access to telephone numbers of thefollowing additional services depending on your needs:

� Hotels

� Glass replacement

� Tire repair facilities

� Rental vehicle or taxis

� Airports or train stations

� Police, fire department or hospitals

In many instances, mechanical failures are coveredunder Pontiac’s comprehensive warranty. However,when other services are utilized, our advisors willexplain any payment obligations you might incur.

For prompt and efficient assistance when calling, pleaseprovide the following information to give the advisor:

� Location of vehicle

� Telephone number of your location

� Vehicle model, year and color

� Mileage of vehicle

� Vehicle Identification Number (VIN)

� Vehicle license plate number

Pontiac reserves the right to limit services orreimbursement to an owner or driver when, in Pontiac’sjudgement, the claims become excessive in frequency ortype of occurrence.

While we hope you never have the occasion to use ourservice, it is added security while traveling for you andyour family. Remember, we’re only a phone call away.Pontiac Roadside Assistance -- 1-800-ROADSIDE or 1-800-762-3743.

Canadian Roadside AssistanceVehicles purchased in Canada have an extensiveRoadside Assistance program accessible from anywherein Canada or the United States. Please refer to theseparate brochure provided by the dealer or call1-800-268-6800 for emergency services.

8-10

Courtesy TransportationPontiac has always exemplified quality and value in itsoffering of motor vehicles. To enhance your ownershipexperience, we and our participating dealers are proud tooffer Courtesy Transportation, a customer supportprogram for new vehicles.

The Courtesy Transportation program is offered to retail purchase/lease customers in conjunction with theBumper-to-Bumper coverage provided by the NewVehicle Limited Warranty. Several transportation optionsare available when warranty repairs are required. This willreduce your inconvenience during warranty repairs.

Plan Ahead When PossibleWhen your vehicle requires warranty service, youshould contact your dealer and request an appointment.By scheduling a service appointment and advising yourservice consultant of your transportation needs, yourdealer can help minimize your inconvenience. If yourvehicle cannot be scheduled into the service departmentimmediately, keep driving it until it can be scheduled forservice, unless, of course, the problem is safety-related.If it is, please call your dealership, let them know this,and ask for instructions.

If the dealer requests that you simply drop the vehicleoff for service, you are urged to do so as early in thework day as possible to allow for same day repair.

Transportation OptionsWarranty service can generally be completed while youwait. However, if you are unable to wait Pontiac helpsminimize your inconvenience by providing severaltransportation options. Depending on the circumstances,your dealer can offer you one of the following:

Shuttle Service

Participating dealers can provide you with shuttle serviceto get you to your destination with minimal interruption ofyour daily schedule. This includes a one way shuttle rideto a destination up to 10 miles from the dealership.

Public Transportation or Fuel Reimbursement

If your vehicle requires overnight warranty repairs,reimbursement up to $30 per day (five days maximum)may be available for the use of public transportationsuch as taxi or bus. In addition, should you arrangetransportation through a friend or relative,reimbursement for reasonable fuel expenses up to $10 per day (five day maximum) may be available.Claim amounts should reflect actual costs and besupported by original receipts.

8-11

Courtesy Rental Vehicle

When your vehicle is unavailable due to overnightwarranty repairs, your dealer may arrange to provide youwith a courtesy rental vehicle or reimburse you for a rentalvehicle you obtained, at actual cost, up to a maximum of$30.00 per day supported by receipts. This requires thatyou sign and complete a rental agreement and meet state,local and rental vehicle provider requirements.Requirements vary and may include minimum agerequirements, insurance coverage, credit card, etc. You areresponsible for fuel usage charges and may also beresponsible for taxes, levies, usage fees, excessive mileageor rental usage beyond the completion of the repair.

Generally it is not possible to provide a like-vehicle as acourtesy rental.

Additional Program InformationCourtesy Transportation is available during theBumper-to-Bumper warranty coverage period, but it is notpart of the New Vehicle Limited Warranty. A separatebooklet entitled “Warranty and Owner AssistanceInformation” furnished with each new vehicle providesdetailed warranty coverage information.

Courtesy Transportation is available only atparticipating dealers and all program options, such asshuttle service, may not be available at every dealer.Please contact your dealer for specific information aboutavailability. All Courtesy Transportation arrangementswill be administered by appropriate dealer personnel.

Canadian Vehicles: For warranty repairs during theComplete Vehicle Coverage period of the GeneralMotors of Canada New Vehicle Limited Warranty,alternative transportation may be available under theCourtesy Transportation Program. Please consult yourdealer for details.

General Motors reserves the right to unilaterally modify,change or discontinue Courtesy Transportation at anytime and to resolve all questions of claim eligibilitypursuant to the terms and conditions described herein at its sole discretion.

Warranty InformationYour vehicle comes with a separate warranty bookletthat contains detailed warranty information.

8-12

REPORTING SAFETY DEFECTSTO THE UNITED STATESGOVERNMENTIf you believe that your vehicle has a defect which couldcause a crash or could cause injury or death, you shouldimmediately inform the National Highway TrafficSafety Administration (NHTSA), in addition tonotifying General Motors.

If NHTSA receives similar complaints, it may open aninvestigation, and if it finds that a safety defect exists ina group of vehicles, it may order a recall and remedycampaign. However, NHTSA cannot become involvedin individual problems between you, your dealer orGeneral Motors.

To contact NHTSA, you may either call the Auto SafetyHotline toll-free at 1-800-424-9393 (or 366-0123 in the Washington, D.C. area) or write to:

NHTSA, U.S. Department of TransportationWashington, D.C. 20590

You can also obtain other information about motorvehicle safety from the hotline.

REPORTING SAFETY DEFECTSTO THE CANADIANGOVERNMENTIf you live in Canada, and you believe that your vehiclehas a safety defect, you should immediately notifyTransport Canada, in addition to notifying GeneralMotors of Canada Limited. You may write to:

Transport Canada330 Sparks StreetTower COttawa, Ontario K1A 0N5

8-13

REPORTING SAFETY DEFECTSTO GENERAL MOTORSIn addition to notifying NHTSA (or Transport Canada)in a situation like this, we certainly hope you’ll notifyus. Please call us at 1–800–762-2737, or write:

Pontiac-GMC Customer Assistance CenterP.O. Box 436008Pontiac, MI 48343-6008

In Canada, please call us at 1-800-263-3777 (English)or 1-800-263-7854 (French). Or, write:

General Motors of Canada LimitedCustomer Communication Centre, 163-0051908 Colonel Sam DriveOshawa, Ontario L1H 8P7

Ordering Owner Publications in CanadaOwner’s manuals are available for purchase for allcurrent and most past model General Motors vehicles.

The toll-free telephone number for ordering informationin Canada is 1-800-668-5539.

8-14

CURRENT PUBLICATIONS FOR 2000 PONTIAC

SERVICE MANUALSService Manuals have the diagnosis and repair informationon engines, transmission, axle, suspension, brakes,electrical, steering, body, etc.RETAIL SELL PRICE: $120.00

TRANSMISSION, TRANSAXLE, TRANSFER CASEUNIT REPAIR MANUALThis manual provides information on unit repair serviceprocedures, adjustments and specifications for the 2000 GM transmissions, transaxles and transfer cases.RETAIL SELL PRICE: $50.00

SERVICE BULLETINSService Bulletins give technical service information neededto knowledgeably service General Motors cars and trucks.Each bulletin contains instructions to assist in thediagnosis and service of your vehicle.

OWNER’S INFORMATIONOwner publications are written directly for Owners andintended to provide basic operational information about thevehicle. The owner’s manual will include the MaintenanceSchedule for all models.

In-Portfolio: Includes a Portfolio, Owner’s Manual andWarranty Booklet.RETAIL SELL PRICE: $20.00

Without Portfolio: Owner’s Manual only.RETAIL SELL PRICE: $15.00

CURRENT & PAST MODEL ORDER FORMSService Publications are available for current and pastmodel GM vehicles. To request an order form, pleasespecify year and model name of the vehicle.

PLEASE COMPLETE THE ORDER FORM SHOWN ONTHE FOLLOWING PAGE AND MAIL TO:

Helm, Incorporated � P.O. Box 07130 � Detroit, MI 48207

OR ORDER TOLL FREE: 1-800-551-4123Monday-Friday 8:00 AM – 6:00 PM Eastern Time

For Credit Card Orders Only (VISA–MasterCard–Discover)

2000 PONTIAC SERVICE PUBLICATIONS ORDERING INFORMATION

The following publications covering the operation and servicing of your vehicle can be purchased by filling outthe Service Publication Order Form in this book and mailing it in with your check, money order,

or credit card information to Helm, Incorporated (address below.)

8-15

PUBLICATION FORMNUMBER

Orders will be mailed within 10 days of receipt. Please allow adequate time for postalservice. If further information is needed, write to the address shown below or call1-800-551-4123. Material cannot be returned for credit without packing slip with returninformation within 30 days of delivery. On returns, a re-stocking fee may be appliedagainst the original order.

ORDER TOLL FREE(NOTE: For Credit Card Holders Only)

1-800-551-4123(Monday-Friday 8:00 AM – 6:00 PM EST)

FAX Orders Only 1-313-865-5927

Service Manual

NOTE: Dealers and Companies please provide dealer or company name, and also thename of the person to whose attention the shipment should be sent. Mail completed order form to:

HELM, INCORPORATED � P.O. Box 07130 � Detroit, MI 48207For purchases outside U.S.A. please write to the above address for quotation.

2000 $120.00

2000 $50.00

2000 $20.00

2000 $15.00

TOTAL MATERIAL

Michigan Purchasers

U.S. Order Processing $6.00Canadian Postage

GRAND TOTAL

add 6% sales tax

(See Note Below)

GM-PON-ORD99 *(Prices are subject to change without notice and without incurringobligation. Allow ample time for delivery.)

Note to Canadian Customers: All listed prices are quoted in U.S. funds. Canadian residentsare to make checks payable in U.S. funds. To cover Canadian postage, add $11.50 plus theU.S. order processing.

(CUSTOMER’S NAME) (ATTENTION)

(STREET ADDRESS—NO P.O. BOX NUMBERS)

(CITY) (ZIP CODE)

DAYTIME TELEPHONE NO.

(STATE)

AREA CODE

( )

PCheck or Money Order payable to

Helm, Inc. (USA fundsonly — do not send cash.)

VISA

Discover

AccountNumber:

ExpirationDate mo/yr:

CUSTOMER SIGNATURE

S

ITEM DESCRIPTIONNAME YEAR

VEHICLE MODELQTY. PRICE

EACH*TOTALPRICE2

000

GM

HIP TO

AYMENT

Owner’s Manual Without Portfolio

Owner’s Manual In Portfolio

Car & Light TruckTransmission Unit Repair

MasterCard

Check here if your billing address is different from your shipping address shown.

PUBLICATION FORMNUMBER