Overview - Cisco€¦ · 1-4 PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter...
Transcript of Overview - Cisco€¦ · 1-4 PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter...
PA-2FE-TX and PA-2FE-FX Two-Port Fast EOL-3474-07
C H A P T E R1
OverviewThis chapter describes the PA-2FE port adapter and contains the following sections:
• Port Adapter Overview, page 1-1
• Fast Ethernet Overview, page 1-2
• IEEE 802.3u 100BASE-T Specifications, page 1-2
• LEDs, page 1-4
• Receptacles, Cables, and Pinouts, page 1-4
• Network Management, page 1-6
• Port Adapter Slot Locations on the Supported Platforms, page 1-7
• Identifying Interface Addresses, page 1-16
Port Adapter OverviewThe PA-2FE provides two 10/100-Mbps, 10/100BASE-T Fast Ethernet/Inter-Switch Link (ISL) interfaces and supports both full-duplex and half-duplex operation. Refer to the “Fast Ethernet Overview” section on page 1-2 for additional information.
Both models of the PA-2FE (PA-2FE-TX and PA-2FE-FX) are shown in Figure 1-1 and Figure 1-2.
Figure 1-1 PA-2FE-TX—Faceplate View
Figure 1-2 PA-2FE-FX—Faceplate View
4645
3
ENABLED
LINK0TX0
RX0RX1
LINK1TX1
PA-2FE-TX
0 1
4645
4
ENABLED
0LINK0TX0
RX0RX1
LINK1TX1TXRX 1 TX
PA-2FE-FX
RX
CLASS 1
LED P
RODUCT
P
RODUKT
MIT
KLA
SSE 1 L
ED
PRO
DUIT A
VEC VOYA
NT DEL
D
E CLA
SSE 1PRO
DUCTO L
ED DE C
LASE 1
1-1thernet Port Adapter Installation and Configuration
Chapter 1 Overview Fast Ethernet Overview
Fast Ethernet OverviewThe term Ethernet is commonly used for all carrier sense multiple access collision detect (CSMA/CD) LANs that generally conform to Ethernet specifications, including Fast Ethernet under IEEE 802.3u.
Note 100BASE-TX is intended for Environment A, and 100BASE-FX is intended for Environment B. Both are described in the IEEE 802.3u standard.
IEEE 802.3u is well suited to applications where a local communication medium must carry sporadic, occasionally heavy traffic at peak data rates. Stations on a CSMA/CD LAN can access the network at any time. Before sending data, the station listens to the network to see if it is already in use. If it is in use, the station waits until the network is not in use, then transmits. This process is known as half-duplex operation. A collision occurs when two stations listen for network traffic, hear none, and transmit almost simultaneously. When simultaneous transmission occurs, both transmissions are damaged and the stations must retransmit. The stations detect the collision and use backoff algorithms to determine when they should retransmit.
Both Ethernet and IEEE 802.3u are broadcast networks, which means that all stations see all transmissions. Each station must examine received frames to determine whether it is the intended destination and, if it is, pass the frame to a higher protocol layer for processing.
IEEE 802.3u specifies the following different physical layers for 100BASE-T:
• 100BASE-TX—100BASE-T, half- and full-duplex over Category 5 UTP, EIA/TIA–568-compliant cable
• 100BASE-FX—100BASE-T, half- and full-duplex over optical fiber
Each physical layer protocol has a name that summarizes its characteristics in the format speed/signaling method/segment length, where speed is the LAN speed in megabits per second (Mbps), signaling method is the signaling method used (either baseband or broadband), and segment length is the maximum length between stations in hundreds of meters. Therefore, 100BASE-T specifies a 100-Mbps, baseband LAN with maximum network segments.
IEEE 802.3u 100BASE-T SpecificationsThis section provides specifications for IEEE 802.3u 100BASE-T. Table 1-1 provides cabling specifications for 100BASE-TX Fast Ethernet transmission over UTP and foil twisted-pair (FTP), and 100BASE-FX Fast Ethernet over fiber-optic cables. It also summarizes IEEE 802.3u 100BASE-TX and 100BASE-FX physical characteristics. (See Figure 1-3.)
Table 1-1 Cabling Specifications
Parameter 100BASE-TX 100BASE-FX (Multimode)
Cable specification Category 51 UTP2, 22 to 24 AWG
62.5/125 multimode optical fiber
Maximum segment length (half-duplex)3
100 m 412 m
Maximum segment length (full-duplex)3
100 m 2000 m
1-2PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview IEEE 802.3u 100BASE-T Specifications
Figure 1-3 Maximum Segment and Network Lengths—100BASE--FX and 100BASE-TX
Maximum network length (half-duplex, one repeater)4
200 m 272 m
Data rate 100 Mbps 100 Mbps
Signaling method 4B/5B5 block coded, scrambled, with MLT-3 line coding
4B/5B block coded, with NRZI line coding
Connector RJ-45 (ISO/IEC 60603-7:-1990 SC-type: dual simplex or single duplex for RX and TX
Topology Star/hub Star/hub
1. EIA/TIA-568 or EIA-TIA-568 TSB-36 compliant.
2. Cisco does not supply Category 5 UTP RJ-45 cables. However, they are available commercially.
3. Data Terminal Equipment (DTE to DTE), see Figure 1-3.
4. DTE to Repeater to DTE, see Figure 1-3.
5. 4B/5B encoding or block coding, encodes four data bits into a 5-bit transmission sequence.
Table 1-1 Cabling Specifications (continued)
Parameter 100BASE-TX 100BASE-FX (Multimode)
Maximum segment length, full duplex
100 m TXDTEDTE*
*DTE = Data Terminal Equipment
**Because repeaters have more delay, total network length is shorter.
2000 m FX–multimode
Maximum segment length, half duplex
100 m TXDTEDTE
412 m FX
Maximum segment length, full duplex
10,000 m FX–single modeDTEDTE
Maximum network length, half duplex
200 m TXDTEDTE R
(Repeater)
272 m FX**
3170
3
1-3PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview LEDs
Note PA-2FE-FX uses 62.5/125-micron multimode fiber with an SC connector.
LEDsThe PA-2FE has seven LEDS; an ENABLED LED, and LINK, TRANSMIT, and RECEIVE LEDs for each port. The LEDs are shown in Figure 1-4.
Figure 1-4 PA-2FE LEDs—Faceplate View of PA-2FE-TX
After system initialization, the ENABLED LED goes on to indicate that the PA-2FE is ready for operation. The following conditions must be met before the ENABLED LED goes on:
• The PA-2FE is correctly connected and receiving power.
• A PA-2FE–equipped card or chassis contains a valid microcode version that has been successfully downloaded.
• The bus recognizes the PA-2FE.
If any of these conditions are not met, or if the initialization fails for other reasons, the ENABLED LED does not go on. Table 1-2 lists LED colors and indicator functions.
Receptacles, Cables, and PinoutsThe two interface receptacles on the PA-2FE are a single RJ-45 connection (on the PA-2FE-TX) or an SC-type optical-fiber connection (on the PA-2FE-FX). Each connection supports IEEE 802.3u interfaces compliant with the 100BASE-X and 10/100BASE-T standards. The RJ-45 connection does not require an external transceiver.
4645
3
ENABLED
LINK0TX0
RX0RX1
LINK1TX1
PA-2FE-TX
0 1
Table 1-2 PA-2FE LEDs
LED Label Color State Function
ENABLED Green On Port adapter is enabled for operation.
LINK0 Green On Port 0 is receiving a carrier signal from the network.1
1. When an RJ-45 or SC port is active.
TX0 Green On Port 0 is transmitting data.
RX0 Green On Port 0 is receiving data.
RX1 Green On Port 1 is receiving data.
TX1 Green On Port 1 is transmitting data.
LINK1 Green On Port 1 is receiving a carrier signal from the network.1
1-4PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Receptacles, Cables, and Pinouts
Figure 1-5 shows the RJ-45 cable connectors. Cisco does not supply Category 5 UTP RJ-45 cables; they are available from a commercial supplier. Table 1-3 lists the pinouts and signals for the PA-2FE-TX RJ-45 connectors.
Figure 1-5 RJ-45 Port and Connector
Note Referring to the RJ-45 pinout in Table 1-3, proper common-mode line terminations should be used for the unused Category 5, UTP cable pairs 4/5 and 7/8. Common-mode line termination reduces the contributions to electromagnetic interference (EMI) and susceptibility to common-mode sources. Wire pairs 4/5 and 7/8 are passively terminated in the RJ-45 100BASE-TX port circuitry in the PA-2FE-TX.
Depending on your RJ-45 interface cabling requirements, use the pinouts in Figure 1-6 and Figure 1-7.
Figure 1-6 Straight-Through Cable Pinout—PA-2FE-TX RJ-45 Connection to a Hub or Repeater
1 RJ-45 connector and port
Table 1-3 IRJ-45 Port Pinout Information
Pin Description
1 TxD+1
1. TxD = Transmit data
2 TxD–
3 RxD+2
2. RxD = Receive data
6 RxD–
8452
9
12345678
1
Ethernet port Hub
1 TxD+2 TxD–
3 RxD+6 RxD–
1 RxD+2 RxD–
3 TxD+6 TxD– 38
582
1-5PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Network Management
Figure 1-7 Crossover Cable Pinout—PA-2FE-TX RJ-45 Connections Between Hubs and Repeaters
Figure 1-8 shows the duplex SC connector (one required for both transmit and receive), and Figure 1-9 shows the simplex SC connector (two required, one each for transmit and receive) used for PA-2FE-FX optical-fiber connections. Cisco does not supply these multimode optical-fiber cables; they are available from a commercial supplier.
Figure 1-8 PA-2FE-FX Duplex SC Connector
Figure 1-9 PA-2FE-FX Simplex SC Connector
Network ManagementThe PA-2FE supports the following:
• SNMP agent v1 (RFC 1155–1157)
• Ethernet MIB (RFC 1398)
• IEEE 802.3 LAN specification for CSMA/CD
• MIB for Network Management of TCP/IP-Based Internets: MIB-II (RFC 1213)
• Definition of Managed Objects for Bridges (RFC 1493)
• Evolution of Interfaces Group of MIB-II (RFC 1573)
Ethernet port
1 TxD+
2 TxD–
3 RxD+
6 RxD–
1 TxD+
2 TxD–
3 RxD+
6 RxD– 3858
3
DTE
H2
21
4
H23
99
1-6PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms
Port Adapter Slot Locations on the Supported PlatformsThis section discusses port adapter slot locations on the supported platforms. The illustrations that follow summarize slot location conventions on each platform:
• Cisco 7100 Series Routers Slot Numbering, page 1-7
• Cisco 7200 Series Routers and Cisco 7200 VXR Routers Slot Numbering, page 1-8
• Cisco uBR7200 Series Router Slot Numbering, page 1-9
• Cisco 7201 Router Slot Numbering, page 1-10
• Cisco 7301 Router Slot Numbering, page 1-10
• Cisco 7304 PCI Port Adapter Carrier Card Slot Numbering, page 1-11
• Cisco 7401ASR Router Slot Numbering, page 1-12
• Cisco 7500 Series Routers with VIP Slot Numbering, page 1-12
Note The port adapters shown in the slot identification illustrations may not be the same port adapter that is documented in this guide.
Cisco 7100 Series Routers Slot Numbering The PA-2FE can be installed in port adapter slot 3 in Cisco 7120 series routers, and in port adapter slot 4 in Cisco 7140 series routers. Figure 1-10 shows the slot numbering on a Cisco 7120 series router. Figure 1-11 shows the slot numbering on a Cisco 7140 series router.
Figure 1-10 Port Adapter Slots in the Cisco 7120 Series Router
SLOT 0 SLOT 1
0
2
FE 0 / 0 FE AUX
7120 - AE3
RXTXE3RXEN
CEL CAR ALM
5
ICONS
ACT
0 / 1
ACT
LNK0
LNK1
PWR
SYSRDY
Slot 1 Slot 0
Slot 3 Slot 4Slot 5
1849
8
Slot 2
1-7PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms
Figure 1-11 Port Adapter Slots in the Cisco 7140 Series Router
Cisco 7200 Series Routers and Cisco 7200 VXR Routers Slot NumberingCisco 7202 routers have two port adapter slots. The slots are numbered from left to right. You can place the port adapters in either of the slots (slot 1 or slot 2). The Cisco 7202 router is not shown.
Cisco 7204 routers and Cisco 7204VXR routers have four slots for port adapters, and one slot for an input/output (I/O) controller. The slots are numbered from the lower left to the upper right, beginning with slot 1 and continuing through slot 4.You can place the port adapters in any of the slots (slot 1 through slot 4). Slot 0 is always reserved for the I/O controller. The Cisco 7204 router and Cisco 7204VXR are not shown
Cisco 7206 routers and Cisco 7206VXR routers have six slots for port adapters, and one slot for an input/output (I/O) controller. The slots are numbered from the lower left to the upper right, beginning with slot 1 and continuing through slot 6. You can place the port adapters in any of the six slots (slot 1 through slot 6). Slot 0 is always reserved for the I/O controller. Figure 1-12 shows the slot numbering on a Cisco 7206 router. The Cisco 7206VXR router is not shown.
Figure 1-12 Port Adapter Slots in the Cisco 7206 Router
SLOT 0 SLOT 1
AC OK
DC OK
OTF
AC OK
DC OK
OTF
5
155 - MMRXRXEN
CEL CAR ALM
TXI155 - MM CONSFE 0 / 0 FE
ACT
0 / 1 AUX
0
2RX
7140 - 2MM3
RXEN
CEL CAR ALM
TX
ACT
LNK0
LNK1
PWR
SYSRDY
ENERROR
BOOTRESETSM-ISM
1849
9
Slot 1 Slot 0 Slot 2
Slot 4Slot 5 Slot 3
2832
9
2ETHERNET-10BFL
EN
RX
0 1 2 3 4TX RX TX RX TX RX TX RX TX
0
4
1
3
56
TOKEN RING
0 1 2 3
Cisco 7200Series
FAST ETHERNET INPUT/OUTPUT CONTROLLER
ENABLED
PCMCIA
EJECT
SLOT 0
SLOT 1
FE MII
EN
0 71 2 3 4 5 6SERIAL-V.35
ETHERNET 10BT
ENABLE
D
0 2
1 3
LINK
0 1 2 3
MII
EN RJ-45
EN
RJ-45
RJ-45
LINK
1O P
WR
OK
ENABLE
D
MII
LIN
K
RJ4
5
FAST ETHERNET
0
Port adapter slot 5
Port adapter slot 3
Port adapter slot 1
Port adapter slot 6
Port adapter slot 4
Port adapter slot 2
Port adapter slot 0
1-8PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms
Cisco uBR7200 Series Router Slot NumberingThe Cisco uBR7223 router has one port adapter slot (slot 1). Slot 0 is always reserved for the I/O controller—if present. The Cisco uBR7223 router is not shown.
The Cisco uBR7246 router and Cisco uBR7246VXR router have two port adapter slots (slot1 and slot 2). Slot 0 is always reserved for the I/O controller—if present. Figure 1-13 shows the slot numbering of port adapters on a Cisco uBR7246VXR router. The Cisco uBR7246 router is not shown.
Figure 1-13 Port Adapter Slots in the Cisco uBR7246VXR Router
ENABLED
DSuBR - MCI6
US USUS US0 1 2
5
ENABLED
DSuBR - MCI6
US USUS US0 1 2
5
ENABLED
DSuBR - MCI6
US USUS US
US US0 1 2 3 4 5
ENABLED
DSuBR - MCI6
US USUS US0 1 2
5
H11
323
Cable modem card slot 3Cable modem card slot 4
Cable modem card slot 5Cable modem card slot 6
Port adapter slot 0(I/O controller)
Port adapter slot 1 (blank)
Port adapter slot 2
1-9PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms
Cisco 7201 Router Slot NumberingFigure 1-14 shows the front view of a Cisco 7201 router with a port adapter installed. There is only one port adapter slot (slot 1) in a Cisco 7201 router.
Figure 1-14 Port Adapter Slot in the Cisco 7201 Router
Cisco 7301 Router Slot NumberingFigure 1-15 shows the front view of a Cisco 7301 router with a port adapter installed. There is only one port adapter slot (slot 1) in a Cisco 7301 router.
Figure 1-15 Port Adapter Slot in the Cisco 7301 Router
230308
ENAB
LED
RX CE
LLS
RX CA
RRIER
RX AL
ARM
ATM
GE 0/0
GE 0/1GE 0/2
GE 0/3AUX
CONSOLE
MNGMNT USE ONLY
FELINK
0FE 0/0
RJ45SFP
SFPSFP
SFP
LINK/ACTV
ALARM
PWR OK
STATUS
CFACTV
COMPACT FLASH
LINK/ACTV
RXTX
LINK/ACTV
LINK/ACTV
RXTX
EN
RJ45 EN
PASLOT 1
Cisco 7201
Port adapter slot
ALARM
RJ45 ENLINK
TXRX
GBIC
GIGABIT ETHERNET 0/2
CISCO 7400SERIESCISCO 7411
SLOT 1
CONSOLEAUX
COMPACTFLASH STATUS
100-240V, 2A, 50/60 Hz24V=9A, 48 - 60V=5A
RJ45 ENLINK
TXRX
GBIC
GIGABIT ETHERNET 0/1
RJ45 ENLINK
TXRX
GBIC
GIGABIT ETHERNET 0/0
ENAB
LED
RX CE
LLS
RX CA
RRIER
RX AL
ARM
ATM
8498
8
Port adapter slot
1-10PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms
Cisco 7304 PCI Port Adapter Carrier Card Slot Numbering The Cisco 7304 PCI port adapter carrier card installs into Cisco 7304 router module slots 2 through 5. Figure 1-16 shows the module slot numbering on a Cisco 7304 router. The port adapter slot number is the same as the module slot number. Slot 0 and slot 1 are reserved for the NPE module or NSE module.
Figure 1-16 Module Slots on the Cisco 7304 Router
The Cisco 7304 PCI port adapter carrier card accepts one single-width port adapter. Figure 1-17 shows a Cisco 7304 PCI port adapter carrier card with a port adapter installed.
Figure 1-17 Cisco 7304 PCI Port Adapter Carrier Card—Port Adapter Installed
TX
9K-10C48
1-PORT OC48 POS w/ SMSR
OIR
STATUS
RX
OIR
STATUS
9K-40C3/POS-MM
4-PORT OC3 POS w/ MM
OIR
STATUS
CARRIER/ALARM
0
ACTIVE/LOOPBACK
12
3
CARRIER/ALARM ACTIVE/LOOPBACK CARRIER/ALARM ACTIVE/LOOPBACK
7300-2OC3ATM-MM
2-PORT OC3 ATM MM
OIR
STATUS
0 RXTX
1 RXTX
7055
0
Slot 1
Slot 0
Slot 2
Slot 3
Slot 4
Slot 5
8465
3
7300-CC-PA
OIRSTATUS
7300 PA CARRIER
ENAB
LED
RX CE
LLS
RX CA
RRIER
RX AL
ARM
ATM
1-11PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms
Cisco 7401ASR Router Slot NumberingFigure 1-18 shows the front view of a Cisco 7401ASR router with a port adapter installed. There is only one port adapter slot (slot 1) in a Cisco 7401ASR router.
Figure 1-18 Port Adapter Slot in the Cisco 7401ASR Router
Cisco 7500 Series Routers with VIP Slot NumberingThe PA-2FE is supported on theVIP2, VIP4, VIP6-80 versatile interface processors used in Cisco 7500 series routers. In the Cisco 7505 router, the VIP motherboard is installed horizontally in the VIP slot. In the Cisco 7507 router and Cisco 7513 router, the VIP motherboard is installed vertically in the VIP slot. The port adapter can be installed in either bay (port adapter slot 0 or 1) on the VIP. The bays are numbered from left to right on the VIP. Figure 1-19 shows the slot numbering on a VIP.
Figure 1-19 VIP Slot Locations
5768
0
ENAB
LED
RX CE
LLS
RX CA
RRIER
RX AL
ARM
TX
RX ENHANCED ATM
1 VIP port adapter slot 0 2 VIP port adapter slot 1
1297
20
21
1-12PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms
Cisco 7505 routers have four slots for port adapters, and one slot for a Route Switch Processor (RSP). The slots are numbered from bottom to top. You can place the port adapters in any of the VIP interface slots (slot 0 through 3). One slot is always reserved for the RSP. Figure 1-20 shows the slot numbering on a Cisco 7505 router.
Figure 1-20 VIP Slots in the Cisco 7505 Router
1 RSP 4 VIP interface—slot 1
2 VIP interface—slot 3 5 VIP interface—slot 0
3 VIP interface—slot 2
1221
93
EJECT
SLOT 0SLO
T 1
NORMAL CPU HALT
RESET
AUX.
CONSOLE
ROUTE SWITCH PROCESSOR
ENABLE
ENABLE
1
2
3
4
5
1-13PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms
Cisco 7507 routers have five slots for port adapters, and two slots for RSPs. The slots are numbered from left to right. You can place the port adapters in any of the VIP interface slots (slot 0, 1, 4, 5, or 6). Slots 2 and 3 are always reserved for RSPs. Figure 1-21 shows the slot numbering on a Cisco 7507 router.
Figure 1-21 VIP Slots in the Cisco 7507 Router
1 VIP interface—slot 0 5 VIP interface—slot 4
2 VIP interface—slot 1 6 VIP interface—slot 5
3 RSP—slot 2 7 VIP interface—slot 6
4 RSP—slot 3
ENABLE
ENABLE
EJECT
SLOT 0
SLOT 1
NORMAL
CPU HALTRESET
AUX.
CONSOLE
RO
UT
E SW
ITC
H PR
OC
ESSO
R 2
SLAVE
MASTER
SLAVE/MASTER
1221
94
I
O
DC FAILAC POWER
I
O
DC FAILAC POWER
1 2 3 4 5 6 7
1-14PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Port Adapter Slot Locations on the Supported Platforms
Cisco 7513 routers have eleven slots for port adapters, and two slots for RSPs. The slots are numbered from left to right. You can place the port adapters in any of the VIP interface slots (slots 0 through 5, or slots 9 through 12). Slots 6 and 7 are always reserved for RSPs. Figure 1-22 shows the slot numbering on a Cisco 7513 router.
Figure 1-22 VIP Slots in the Cisco 7513 Router
1 VIP interface—slot 0 8 RSP—slot 7
2 VIP interface—slot 1 9 VIP interface—slot 8
3 VIP interface—slot 2 10 VIP interface—slot 9
4 VIP interface—slot 3 11 VIP interface—slot 10
5 VIP interface—slot 4 12 VIP interface—slot 11
6 VIP interface—slot 5 13 VIP interface—slot 12
7 RSP—slot 6
EJECT
SLOT 0
SLOT 1
NORMAL
CPU HALTRESET
AUX.
CONSOLE
RO
UT
E SW
ITC
H PR
OC
ESSO
R 2
SLAVE
MASTER
SLAVE/MASTER
ENABLE
ENABLE
1221
95
EJECT
SLOT 0
SLOT 1
NORMAL
CPU HALTRESET
AUX.
CONSOLE
RO
UT
E SW
ITC
H PR
OC
ESSO
R 2
SLAVE
MASTER
SLAVE/MASTER
0
I
ACOK
FANOK
OUTPUTFAIL
0
I
ACOK
FANOK
OUTPUTFAIL
POWER
APOWER
B
12
34
56
78
910
1112
13
1-15PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Identifying Interface Addresses
Identifying Interface Addresses The following sections describe the interface address formats for the PA-2FE in supported platforms. Interface addresses specify the actual physical location of each interface on a router or switch.
Interfaces on a PA-2FE installed in a router maintain the same address regardless of whether other port adapters are installed or removed. However, when you move a port adapter to a different slot, the first number in the interface address changes to reflect the new port adapter slot number.
Interfaces on a PA-2FE installed in a VIP maintain the same address regardless of whether other interface processors are installed or removed. However, when you move a VIP to a different slot, the interface processor slot number changes to reflect the new interface processor slot.
Note Interface ports are numbered from left to right starting with 0.
The following subsections describe the interface address formats for the supported platforms:
• Cisco 7120 Router and Cisco 7140 Router Interface Addresses, page 1-17
• Cisco 7200 Series Routers and Cisco 7200 VXR Routers Interface Addresses, page 1-17
• Cisco uBR7200 Series Routers Interface Addresses, page 1-18
• Cisco 7201 Router Interface Addresses, page 1-18
• Cisco 7301 Router Interface Addresses, page 1-18
• Cisco 7304 PCI Port Adapter Carrier Card Interface Addresses, page 1-18
• Cisco 7401ASR Router Interface Addresses, page 1-18
• Cisco 7500 Series Routers VIP Interface Addresses, page 1-19
Table 1-4 summarizes the interface address formats for the supported platforms.
Table 1-4 Identifying Interface Addresses
Platform Interface Address Format Numbers Syntax
Cisco 7120 series router Port-adapter-slot-number/interface-port-number Port adapter slot—always 3
Interface port—0 or 1
3/0
Cisco 7140 series routers Port-adapter-slot-number/interface-port-number Port adapter slot—always 4
Interface port—0 or 1
4/0
Cisco 7200 series routers and Cisco 7200 VXR routers (Cisco 7202, Cisco 7204, Cisco 7204VXR, Cisco 7206, Cisco 7206VXR)
Port-adapter-slot-number/interface-port-number Port adapter slot—1 through 6 (depends on the number of slots in the router)
Interface port—0 or 1
1/0
Cisco uBR7200 series routers (Cisco uBR7223)
Port-adapter-slot-number/interface-port-number Port adapter slot—1
Interface port—0 or 1
1/0
Cisco uBR7200 series routers (Cisco uBR7246, Cisco uBR7246VXR)
Port-adapter-slot-number/interface-port-number Port adapter slot—1 and 2
Interface port—0 or 1
1/0
1-16PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Identifying Interface Addresses
Note In Cisco 7200 series routers, Cisco 7200 VXR routers, and Cisco uBR7200 series routers, port adapter slot 0 is reserved for the Fast Ethernet port on the I/O controller, if present.
Cisco 7120 Router and Cisco 7140 Router Interface AddressesIn the Cisco 7120 series router, port adapters are installed in port adapter slot 3. See Figure 1-10. In the Cisco 7140 series router, port adapters are installed in port adapter slot 4. See Figure 1-11.
The interface address is composed of a two-part number in the format port-adapter-slot-number/interface-port-number. See Table 1-4. For example, if a dual-port PA-2FE is installed on a Cisco 7120 router, the interface addresses would be 3/0 and 3/1. If a dual-port PA-2FE is installed on a Cisco 7140 router, the interface addresses would be 4/0 and 4/1.
Cisco 7200 Series Routers and Cisco 7200 VXR Routers Interface Addresses In Cisco 7200 series routers and Cisco 7200 VXR routers, port adapter slots are numbered from the lower left to the upper right, beginning with slot 1 and continuing through slot 2 for the Cisco 7202, slot 4 for the Cisco 7204 and Cisco 7204VXR, and slot 6 for the Cisco 7206 and Cisco 7206VXR. Port adapters can be installed in any available port adapter slot from 1 through 6 (depending on the number of slots in the router). (Slot 0 is reserved for the I/O controller.) See Figure 1-12.
The interface address is composed of a two-part number in the format port-adapter-slot-number/interface-port-number. See Table 1-4. For example, if a dual-port PA-2FE is installed in slot 1of a Cisco 7200 series router, the interface addresses would be 1/0 and 1/1 (slot 1 and ports 0 and 1). If the dual-port PA-2FE were installed in slot 4, the interface addresses would be 4/0 and 4/1 (slot 4 and ports 0 and 1)
Cisco 7201 router Port-adapter-slot-number/interface-port-number Port adapter slot—always 1
Interface port—0 or 1
1/0
Cisco 7301 router Port-adapter-slot-number/interface-port-number Port adapter slot—always 1
Interface port—0 or 1
1/0
Cisco 7304 PCI port adapter carrier card in Cisco 7304 router
Module-slot-number/interface-port-number Module slot— slot 2 through 5
Interface port—0 or 1
3/0
Cisco 7401ASR router Port-adapter-slot-number/interface-port-number Port adapter slot—always 1
Interface port—0 or 1
1/0
VIP in Cisco 7500 series routers
Interface-processor-slot-number/port-adapter-slot- number/interface-port-number
Interface processor slot—0 through 12 (depends on the number of slots in the router)
Port adapter slot— 0 or 1
Interface port—0 or 1
3/1/0
Table 1-4 Identifying Interface Addresses (continued)
Platform Interface Address Format Numbers Syntax
1-17PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Identifying Interface Addresses
Cisco uBR7200 Series Routers Interface Addresses In the Cisco uBR7223 router, only one slot accepts port adapters and it is numbered slot 1.
In the Cisco uBR7246 router and Cisco uBR7246VXR router, port adapters can be installed in two port adapter slots (slot1 and slot 2). Slot 0 is always reserved for the I/O controller—if present. See Figure 1-13.
The interface address is composed of a two-part number in the format port-adapter-slot-number/interface-port-number. See Table 1-4. For example, if a dual-port PA-2FE is installed in slot 1of a Cisco uBR7223 series router, the interface addresses would be 1/0 and 1/1 (slot 1 and ports 0 and 1). If the dual-port port adapter were installed in slot 2 of a Cisco uBR7246 or Cisco uBR7248VXR router, the interface addresses would be 2/0 and 2/1 (slot 2 and ports 0 and 1).
Cisco 7201 Router Interface AddressesIn the Cisco 7201 router, only one slot accepts port adapters and it is numbered slot 1. See Figure 1-14.
The interface address is composed of a two-part number in the format port-adapter-slot-number/interface-port-number. See Table 1-4. For example, if a dual-port PA-2FE is installed on a Cisco 7201 router, the interface addresses would be 1/0 and 1/1.
Cisco 7301 Router Interface AddressesIn the Cisco 7301 router, only one slot accepts port adapters and it is numbered slot 1. See Figure 1-15.
The interface address is composed of a two-part number in the format port-adapter-slot-number/interface-port-number. See Table 1-4. For example, if a dual-port PA-2FE is installed on a Cisco 7301 router, the interface addresses would be 1/0 and 1/1.
Cisco 7304 PCI Port Adapter Carrier Card Interface AddressesIn the Cisco 7304 router, port adapters are installed in a Cisco 7304 PCI port adapter carrier card, which installs in Cisco 7304 router module slots 2 through 5. The port adapter slot number is the same as the module slot number. See Figure 1-16.
The interface address is composed of a two-part number in the format module-slot-number/interface-port-number. See Table 1-4. For example, if a dual-port PA-2FE is installed in the Cisco 7304 PCI port adapter carrier card in Cisco 7304 router module slot 3, the interface addresses would be 3/0 and 3/2.
Cisco 7401ASR Router Interface AddressesIn the Cisco 7401ASR router, only one slot accepts port adapters and it is numbered slot 1. See Figure 1-18.
The interface address is composed of a two-part number in the format port-adapter-slot-number/interface-port-number. See Table 1-4. For example, if a dual-port PA-2FE is installed on a Cisco 7401ASR router, the interface addresses would be 1/0 and 1/1.
1-18PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Identifying Interface Addresses
Cisco 7500 Series Routers VIP Interface AddressesIn Cisco 7500 series routers, port adapters are installed on a versatile interface processor (VIP), which installs in interface processor slots 0 through 12 (depending on the number of slots in the router). The port adapter can be installed in either bay (port adapter slot 0 or 1) on the VIP. See Figure 1-19, Figure 1-20, Figure 1-21, and Figure 1-22.
The interface address for the VIP is composed of a three-part number in the format interface-processor-slot-number/port-adapter-slot-number/interface-port-number. See Table 1-4.
The first number identifies the slot in which the VIP is installed (slot 0 through 12, depending on the number of slots in the router).
The second number identifies the bay (port adapter slot) on the VIP in which the port adapter is installed (0 or 1). The bays are numbered from left to right on the VIP.
The third number identifies the physical port number (interface port number) on the port adapter. The port numbers always begin at 0 and are numbered from left to right. The PA-2FE is a dual-port port adapter, therefore the port can be 0 or 1.
For example, if a dual-port PA-2FE is installed in a VIP in interface processor slot 3, port adapter slot 1, the interface addresses would be 3/1/0 and 3/1/1.
Note Although the processor slots in the seven-slot Cisco 7507 and the thirteen-slot Cisco 7513 chassis are vertically oriented and those in the five-slot Cisco 7505 are horizontally oriented, all Cisco 7500 series routers use the same method for slot and port numbering.
1-19PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
Chapter 1 Overview Identifying Interface Addresses
1-20PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07