(All dimensions are approx and are in mm)

Stand Bannerh t t p s : / / w w w . s t a n d b a n n e r . c o . u k

835mm

306mm

3x1 Curved

1240mm

3x2 Curved

1590mm

1930mm

485mm

2540mm

2275mm

685mm

3x3 Curved

3x4 Curved3070mm

2865mm

960mm

3x4 Straight

306mm

2960mm

3435mm

3x3 Straight

306mm

2230mm

2700mm

3x2 Straight

306mm

1505mm

1970mm

3x1 Straight

306mm

770mm

1240mm

Fully magnetic , with silver anodised aluminium frame and sa ron components , Xpressis stylish and very simple to use.

features & bene ts

• S elf-locating hanging system with magnetichangers make it the simplest pop-up toassemble

• S elf-locating ‘smart’ magnetic locking arms andlow pro le mag bars

• Quality anodised aluminium nish

• Available as frame only, graphic hanging kit orfabric panel kit

• Option for graphics to be displayed on bothsides

• All front curve / D–end panels are the samesize

• D–E nd graphic panels also t the Xpress Tower

• S maller graphic s ize ‘Midi’ vers ion available

• Available in a combination of quads from 1 x 1desktop to 5 x 5 freestanding exhibition display

3 x 3 C urved

Stand Bannerh t t p s : / / w w w . s t a n d b a n n e r . c o . u k

Graphic Panel Sizes

1 Quad 2 Quad 3 Quad 4 Quad 5 Quad

Reg Height 776 1495 2225 2968 3710

Midi Height 647 1245 1850 2455 -

All measurements are in millimeters (mm)

Reg 673 807 673

Midi 550 675 673

NB - Widths are consistent regardless of how many quads high the pop-up is.*Straight systems allow + or - 1mm to allow for var iances in �oor surface.

NB - Straight systems of no more than 4 quads high are r ecommended.

Curved Widths Panel HeightsFront Panel Rear Panel D-End

Reg 733* 733* 673

Midi 605* 605* 673

Straight Widths Front Panel Rear Panel D-End

Kit: Mag B ars (for exact number seetable on back page), frame, D-E ndG raphics x 2 and Front and/or reargraphics

Take the frame, ensuring that the coloured nodes are at the top. S tand the frame on the floor (2) andopen up (3) until the locking arms click the frame securely into place (4)

1 2 3 4

Add the mag bars ontothe system for front, D-ends and if applicable,the rear.

5

E nsure that the mag barslock onto the magneticpip securely.

6

Unwrap each graphiccarefully and attach tothe system.

7

C arefully hook the tophanger onto the top nodeon each side of the quad.

8

S mooth the graphic ontothe mag bars , ensuringthat it s its flatand is aligned to thecentre line of each magbar.

9

R epeat for the D-E nd,ensuring that the fit iscorrect.

10 11 12 13

R epeat steps 8 and 9 for the rest of the graphics on theunit. This applies to front and rear graphics ifapplicable.

F inally, attach the 2nd D-E nd.

Important note:R emove all mag barsbefore collapsing theframe.

R emove the backing paperfrom the graphic hanger.

C urved G raphic panel finishing

C urved Pop-up assembly

Apply the hanger to the topins ide edge of the panelensuring that it is flush to thepanel edge.

R emove the backing paperfrom the kicker and apply itto the bottom edge of thepanel.

R emove the backing paperfrom the mag tape. Apply toboth s ides of the panel,keeping it flush to the edge.

NB D-E nd panelsdo not requirekickers .

Stand Bannerh t t p s : / / w w w . s t a n d b a n n e r . c o . u k

S mooth the graphic ontothe mag bars , ensuringthat it s its flatand is aligned to thecentre line of each magbar.

9

10 11 12

Take the frame, ensuring that the coloured nodes are at the top. S tand the frame on the floor (2) andopen up (3) until the locking arms click the frame securely into place (4)

Apply mag tape to straight panels accordingto the diagram (all dimensions are approx).

NB - If us ing graphic panels with straight hangers followthe C urved graphic panel finishing instructions .

NB - If us ing graphic panels with S traight hangers follow the assembly instructions for C urved pop-ups.

1 2 3 4

Add the mag bars ontothe system, vertically forfront and D-end panels .Then add horizontal magbars across the top andbottom of the system.

5

For Double s idedsystems fit mag bars tothe rear, again runningvertically andhorizontally across thepop-up frame.

6

E nsure that the mag barslock onto the magneticpip securely.

7

Unwrap each graphiccarefully and attach tothe system.

8

S traight G raphic panel finishing

C arefully hook the tophanger of the D-endpanels onto the top nodeof the pop-up frame.

R epeat steps 8 and 9 for the rest of the graphics on theunit. This applies to front and rear graphics ifapplicable.

Important note:R emove all mag bars beforecollapsing the frame.

S traight Pop-up assembly (horizontal mag bars)

Stand Bannerh t t p s : / / w w w . s t a n d b a n n e r . c o . u k

Pop Up® Magnetic

Individual Panel Sizes

End Panel673mm x 2230mm

Inside Curve Panel673mm x 2230mm

Outside Curve Panel808mm x 2230mm

Straight Panel733mm x 2230mm

Graphic Guide

4x3

3x3

A stand is described by the number of frame squares wide (panels) x the number of frame squares high. Standardpanel height of 2230mm increases to 2963mm for a 4-squares high frame, 3696mm for 5-squares high, and4429mm for 6-squares high. Additional stabilising is recommended for increased heights, using either weights or ourunique Frame Support Brace.

When designing for end panels, consider they wrap to the back of the frame. Up to 60% of the width of an end panelmay not be visible from directly in front of the stand and designers should remember that.

V E RY Po r t a b l e G r a p h i c D i s p l a y & E x h i b i t i o n S t a n d S y s t e m s a n d B a n n e r & L i t e r a t u r e S t a n d sp r o m o t i n g B r a n d s & C o r p o r a t i o n s w o r l d w i d e

Inside Curve with ends Straight with ends Outside Curve

2230

mm

3232mm

808mm 808mm 808mm 808mm

673mm 673mm 673mm 673mm 673mm

2230

mm

Visible Area 2565mm

mm376mm376 733mm733mm733mm

2230

mm

Visible Area 2745mm

2230

mm

2424mm

808mm 808mm 808mm

2230

mm

673mm 673mm 673mm 673mm 673mm 673mm

Visible Area 3238mm

2230

mm

673mm 733mm 733mm 733mm 733mm 673mm

Visible Area 3478mm

Stand Bannerh t t p s : / / w w w . s t a n d b a n n e r . c o . u k