MF

Made in Germany

Operator's Manual

1622Stand

2 2

Family TypeStand 1622

Edition: 10/2015 - Part.-No. 9009813

CopyrightThis documentation as well as translation hereof are property of cab Produkttechnik GmbH & Co. KG. The replication, conversion, duplication or divulgement of the whole manual or parts of it for other intentions than its original intended purpose demand the previous written authorization by cab.

EditorRegarding questions or comments please contact cab Produkttechnik GmbH & Co. KG.

TopicalityDue to the constant further development of our products discrepancies between documentation and product can occur.Please check www.cab.de for the latest update. Terms and conditionsDeliveries and performances are effected under the General conditions of sale of cab.

Operator's Manual for the following products

Germanycab Produkttechnik GmbH & Co KGPostfach 1904 D-76007 Karlsruhe Wilhelm-Schickard-Str. 14 D-76131 KarlsruheTelefon +49 721 6626-0 Telefax +49 721 6626-249www.cab.de info@cab.de

Francecab technologies s.a.r.l. F-67350 Niedermodern Téléphone +33 388 722 501www.cab.de/fr info.fr@cab.de

USAcab Technology Inc. Tyngsboro MA, 01879 Phone +1 978 649 0293www.cab.de/us info.us@cab.de

Asia cab Technology Co., Ltd.

Junghe, Taipei, Taiwan Phone +886 2 8227 3966www.cab.de/tw info.asia@cab.de

China cab (Shanghai)Trading Co., Ltd.

Phone +86 21 6236-3161www.cab.de/cn info.cn@cab.de

Representatives in other countries on request

2 3Contents

1 Introduction ............................................................................................................................................ 41.1 Instructions ............................................................................................................................................... 41.2 Intended Use ............................................................................................................................................ 41.3 Safety Instruction ..................................................................................................................................... 41.4 Safety Marking ......................................................................................................................................... 51.5 Environment ............................................................................................................................................. 5

2 Product Description ............................................................................................................................... 62.1 Important Features ................................................................................................................................... 62.2 Technical Data .......................................................................................................................................... 62.3 Overview .................................................................................................................................................. 72.4 Contents of Delivery ................................................................................................................................. 8

3 Mounting ................................................................................................................................................. 93.1 Mounting of the Bracket .......................................................................................................................... 93.2 Mounting of the printer ............................................................................................................................. 93.3 Cable Guide ........................................................................................................................................... 103.4 Positional Variants ...................................................................................................................................113.5 Adjusting in Z- and Y- direction .............................................................................................................. 12

4 41.1 Instructions

Important information and instructions in this documentation are designated as follows:

Danger!Draws your attention to an exceptionally grave, impending danger to your health or life.

!Warning!Indicates a hazardous situation that could lead to injuries or material damage.

!Attention!Draws attention to possible dangers, material damage or loss of quality.

iNotice! Gives you tips. They make a working sequence easier or draw attention to important working processes.

Environment!Gives you tips on protecting the environment.

Handling instruction

Reference to section, position, illustration number or document.

Option (accessories, peripheral equipment, special fittings).

Time Information in the display.

1.2 Intended Use• The device is manufactured in accordance with the current technological status and the recognized safety rules.

However, danger to the life and limb of the user or third parties and/or damage to the device and other tangible assets can arise during use.

• The device may only be used for its intended purpose and if it is in perfect working order, and it must be used with regard to safety and dangers as stated in the operating manual.

• The device is designed for mounting and positioning of cab label printer of the Hermes+ Series. The manufac-turer/supplier shall not be liable for damage resulting from unauthorized use; the user shall bear the risk alone.

• Usage for the intended purpose also includes complying with the operating manual, including the manufacturer‘s maintenance recommendations and specifications

iNotice! The complete documentation can currently be found in the Internet.

1.3 Safety Instruction

!Attention!Initiation, adjustments and changing of parts is only for qualified service personal only. Initiation/ Service Manual Applicators

• Do not use the device close to high-voltage power lines.• Perform only those actions described in this operating manual.

Work going beyond this may only be performed by trained personnel or service technicians.• Mind to a standing place with a flat and hard ground.• Do not load over the maximum load of 50 kg.• Always have service work done in a qualified workshop, where the personnel have the technical knowledge and

tools required to do the necessary work.• In case of loosening the Flanged joint, secure the printer with help of a second person.

1 Introduction

4 51.4 Safety Marking

1

2

1:

75kg max.

Maximum load 75kg

2: Signal cover yellow/blackTrip hazard!

!Attention!Never remove or cover safety markings! Replace it in case of damage!

Fig.1 Safety marking

1.5 Environment

Obsolete devices contain valuable recyclable materials that should be sent for recycling. Send to suitable collection points, separately from residual waste.

The modular construction of the print module enables it to be easily disassembled into its component parts. Send the parts for recycling.

1 Introduction

6 62 Product Description2.1 Important Features

• The floor stand is able for right and left printing and labeling systems.• Frequent adjustment of the labelling position in height and depth. Due to the rack regulation system the Hermes+ can

be positioned in X-and Y-axis to the labelling product via hand wheels.• Adjusting via setting feet.

2.2 Technical DataStand 1622

Adjusable feet +/- 15Load max. 75 kgLowere Edge of printer to ground 150 - 1100 mmDepth crosswise to the conveyor belt 120 mmWeight approx. 40 kg

Table 1 Technical Data

6 72.3 Overview

1

2

6

4

5

3

8

7

Fig.2 Overview

1 Axle Z-direction2 Crank handle to change in Z-direction3 Axle Y-direction4 Joint to change the printer position

5 Hand wheel to change in Y-direction6 Flanged joint for printer mounting7 Mounting bracket8 Setting feet (variable)

2 Product Description

z

y

x

8 82 Product Description2.4 Contents of Delivery

1

2

1

23

3 2

3

1 Stand2 Mounting bracket3 Screws M6x14 (4x)

Fig.3 Contents of Delivery

i Notice! Please keep the original packaging in case the applicator must be returned.

8 93 Mounting3.1 Mounting of the Bracket

The Bracket is a mounting element to install a label printer on a floor stand, to integrate it in a production line.

1

2

3

4

5

Fig.4 Mounting the bracket

1. Schrauben (4) auf einer Seite des Bügels lösen und die Schiene (3) abnehmen.2. Schrauben (5) am Knoten (2) lockern.3. Profil (1) des Bügels wie abgebildet durch den knoten (2) führen und mittig positionieren.4. Schrauben (5) festziehen. 5. Schiene (3) ansetzen und mit den Schrauben (4) am Profil befestigen.

3.2 Mounting of the printer

2

3

21

1

Fig.5 Mounting the printer

!Warning!Before you mount the printer, check the hard fitting of the flanged joint. Mounting only with a second Person.

1. Schrauben (2/4x) locker eindrehen, dass zwischen Schraubenkopf und Druckergehäuse ca. 7 mm Abstand besteht.

2. Drucker in die Aussparungen der Schienen (3) des Bügels einhängen.3. Schrauben (1/4x) durch die Löcher in den Schienen (3) des Bügels und dem Drucker einschrauben.4. Schrauben (1) festziehen.5. Kabelverbindungen herstellen und Kabel verlegen, wie im nächsten Kapitel beschrieben.6. Applikator montieren.

10 103 Mounting3.3 Cable Guide

To mount the cabe and tubes in a defined rout is mounted a hinged cable guide.

1

2

4

3

Fig.6 Mounting the cable guide

1. Loosen hinged top nut (2) .2. Pull out the hinged basic nut (4) out of the mounting bracketl (3).3. Put in the cable and tubes (1) into the aperture of the bracket (3) .4. Open the top nut (2) and the basic nut (4) on the arrester..5. Put both over the cable and tubes and close.6. Put in the basic nut (4) in the hole of the bracketl (3) and tighten top nut (2) .

10 113.4 Positional Variants

!Warning!In case of loosening the Flanged joint, secure the printer with help of a second person.

Fig.7 Positional variants of printer direction

To print and apply the labels in the perfect direction to the product line is it possible to mount the printer and appli-cator in a lot of positional variants. So it's possible to realize every apply degree and position. in the pictures i are the basic positional variants to see.

3

1 2

3

1 2

Fig.8 Change the angle of the bracket

1. For changing loosen screws (1) .2. Rotate the bracket (2) in the new position.3. Tighten screws (1) .

!Warning!In case, the printer is mounted, a second person must secure the printer if the screws will be loosen.

3 Mounting

12 123.5 Adjusting in Z- and Y- direction

1

2

z

y

x

Fig.9 Adjusting in Z- and Y- direction

z

y

x

Anschlag

Fig.10 Maximal movement in Y- direction

!Warning!Turn the joint on the Y-Axle only softly to the stopper. A to fast or to strong movement can damage the axle or the joint.

Changing the height via crank handle (1). Changing in Y- direction via hand wheel (2).

3 Mounting