Operators Manual DL3100 - Bijur Delimon

Operators Manual

DL3100Dualine® Automatic Spray Systems

Installation, Operation, Parts List

DL3100 r#3

Dualine™ series - AUTOMATIC SPRAY LUBRICATING SYSTEMS

2

TABLE OF CONTENTS

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Typical system (Pump close to valve panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

System - Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Typical System (Pump remote from valve panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Central Pumping Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Valve Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Lance Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SC400 Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Air Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

SC1-2 Spray Control Valves - Dimensions & Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

SC1-2 Spray Control Valves - Operation & Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

SC1-2 Spray Control Valves - Conversion For After Blow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Location For Valve Panels And Spray Lance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Startup And Maintenance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

System Diagnosis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Illustrations and specifications are not binding in detail.Designs are subject to modification and improvement without notice.

INTRODUCTIONThe spray systems described in this bulletin are used to lubricate large gear and pinion sets such as found on ball mills, rod mills, kilns, etc. Each systems includes an air operated pumping station, a measuring valve panel, a spray nozzle, electrical controls and a number of optional features.

Gear face widths of 2" to 42" can be lubricated with nozzles and nozzle spacing designed accordingly. Since Bijur Delimon gear spray systems operate intermittently they can be thought of as film maintaining devices. Theelectrical controls provide broad cycling flexibility as well as fault monitoring and after blow to purge the nozzles.


3

TYPICAL SYSTEM (Pump Close To Valve Panel)

Figure - 1

SEQUENCE OF OPERATION (System Shown in Fig.1)1. SC400 times out, opening the two solenoid air valves. The pump starts. A measured volume of lubricant discharges from each of the measuring valves to its spray nozzle. Air flows thru the air manifold to the spray nozzles, atomizing the lubricant to a penetrating spray.2. When each measuring valve has discharged once to its spray nozzle, system pressure begins to increase until at a predetermined point, it shifts the reversing valve; (Factory set @ 1500 psi)

Reversing valve limit switch is operated closing the pump solenoid air valve, but a time delay device in the SC400 keeps the nozzle solenoid air valve open for a preset time period after lube flow stops. The air thoroughly cleanses the nozzles.

Lube pressure in the system is relieved to reservoir by the reversing valve and alternate supply line is readied for pressurizing during next pumping cycle when the foregoing sequence is repeated.

NOTE: For component part numbers, refer to fig's. 2 and 3.


4

SCHEMATIC - TYPICAL SYSTEM (Pump Remote From Valve Panel)

Figure - 2SYSTEM DETAILS AND PART NUMBERS

ITEM # PART NUMBER QTY. DESCRIPTION1 9120 1 120lb Air Operated Barrel Pump2 DR460A 1 Reversing Valve3 LD7767CA1 1 Air Control Panel*4 U623 1 Air Pressure switch5 200275 1 Lube Supply Hose Kit (72")6 200324 1 Relief Hose Kit (72")7 200325 1 Air hose Kit (72")8 U1929D (OIL ONLY) 2 2-Way Line Checks9 BY USER 1 Supply Line Pipe or Hose to Panel

*10 F1194G 1 Air Regulator11 LD12361V6 1 Valve Panel12 LD9327-XXXXX 1 Spray Lance13 SC400 1 Timer Control

* Note: Items 4 & 10 sold separately

Refer to Fig. 3 for pumping station details and part numbers. (Page 5)

The spray system layout shown in (Fig.2) provides guidelines for installations where the pump, reversing valve and controls cannot be located close to the valve panel. To assure good pressure distribution under various operating temperature conditions, two pipe supply lines are run from the reversing calve to within 30" of the valve panel. Two 36" hose assemblies are used to connect to the valve panel. The size of the piping for the supply lines can be selected from the table in page 13(Fig. 15).


5

CENTRAL PUMPING STATION

ITEM PART NO. DESCRIPTION

1 9120 120 LB Air Operated Barrel Pump

2 DR460A Reversing Valve

3 LD7767CA1 Air Control Panel

4 U623 Air Pressure Switch

5 200275 Lube Supply Hose Kit (72")

6 200324 Relief Hose Kit (72")

7 200325 Air Hose Kit (72")

8 U1929D (OIL ONLY) 2-Way Line Checks

NOTE: A. The 9120 pump for 120 pound drums is recommended where solvent cut-back lubricants are used. This is to necessitate frequent drum changes to prevent drying and hardening of the lubricant. The 9400 pump for 400 pound drums is available if drying and hardening of the lubricant is not a problem.B. A U623 pressure switch (Item 4) is used to give warning of low pressure and is an optional feature.C. All Central Pumping Stations are for 120 Volts, 60 Cycle, but other voltages and frequencies are available. Electrical timing devices are described on page 8.D. The U1929D two way checks are needed only if the lubricants have fluid characteristics.

Figure - 3


6

VALVE PANELS

START

1/2" NPT AIR SUPPLY

3/4" DIAMETER THRU 8 HOLES

10

15.0

1.5

6.00

34.0

.62

32.75

17.88

.25

3.94

3.94

1.81

3.94

1.81

2.5 APPROX.

14 12

12.881.81

3.94

1.81

7.63

15

PANELNUMBER

NUMBERSPRAY NOZZLES

AVAILABLE PANELS

LD12361V1LD12361V2

LD12361V3LD12361V4LD12361V5

LD12361V6LD12361V7

12

345

67

TABLE 1.

LD12361V8 8

FIGURE - 4

1918

23

7

24

9

22

17

13

1/2" NPT CONDUIT CONNECTION

212016

3

2

5

6

11

3/8" NPSF

LUBE INLET

24

24 6

6

24

4

VALVE PANEL LD12361V8 PARTS LISTITEM # QTY. PART NO. DESCRIPTION

1 4 201222 Hose Assembly with Adapter - 30" long2 1 201502 Kit - Air Supply Hose - 36" long3 1 201595 Valve Solenoid 2-way NC 3/4"NPT 50/60Hz4 8 U1732F Cover Indicator Stem5 4 DM62100A Dualine Valve6 4 201223 Hose Assembly with Adapter - 36" long7 1 F6024MD Filter Air Line 1/2"NPT Auto Drain8 1 LD9340V8P Plate - Mounting9 12 U81D3 Sleeve and Nut 3/8" tube x 3/8"NPT

10 1 U101D2 Nipple 1/2"NPT x 1-1/8" long11 1 U101E1 Nipple 3/4"NPT x 1-3/8" long12 1 U101E19 Nipple 3/4"NPT x 7" long13 1 U11354 Elbow Reducing Pipe 3/4" x 1/2"14 1 U11654 Reducing Coupling15 4 U119CC Plug 3/8"NPT16 4 U204C15 Screw Hex Head Cap 3/8"-16 x 5/8" long17 8 U206K6 Screw Fillet Head Machine 5/16"-18 x 2-1/2" long18 4 U207G3 Screw Round Head Machine #10-24 x 1/2" long19 4 U213C Washer Lock #1020 4 U213G Washer Lock 3/8"21 2 U2685 Bracket Mounting 3/4"NPT22 .75' U424E6 Tubing Steel 3/8" O.D.23 1 LE9629B Pushbutton 'start'24 8 U1104B Ell Street 1/4"NPT

Shown in Fig. 4 is a typical measuring valve panel(Panel assembly#LD12361V8). This panel has measuring valves to serve 8 nozzles. Panels having from 1 to 8 measuring valves are available as shown in Table 1. All panels have outside dimen-sions of 34" X 15". The only variable on each panel is the number of measuring valves(one to eight). DM60 size measuring valves are standard on the panels, however, smaller capacity measuring valves can be supplied if required.


7

SPRAY LANCE - MODEL LD-9327

U10781-1/2"PIPE CAP

1.5" FORGED STEEL SLIP ON FLANGE(NOT FURNISHED BY BDI)

GEAR GUARD

1/2”NPTAIR INLET

1/4”NPTLUBE INLET

LUBE HOSE - REF.

"A"

"C""B""B""B""B""B""B"

U424C63/8"OD TUBING

1-1/2" STEEL PIPE

GEAR GUARD

B6519

U922C U1104B U101B1

B6514

A

A

U1103B

Group 1 - Assembly Numbers and Dimensions

ASSEMBLYPART #

GEAR FACE

WIDTH

GUARD WIDTH

NO. OF SPRAY

NOZZLES

DIMENSIONS

AB

+/- 1/16"

C+/-

1/16"LD93271020S 2" 4.5" 1 8" - 2.25LD93271030S 3" 5.5" 1 10" - 2.75LD93271040S 4" 6.5" 1 11" - 3.25LD93271050S 5" 7.5" 1 12" - 3.75LD93271060S 6" 8.5" 1 13" - 4.50LD93272070S 7" 9.5" 2 14" 4.00 2.25LD93272080S 8" 10.5" 2 15" 4.50 3.00LD93272090S 9" 11.5" 2 16" 4.50 3.50LD93272100S 10" 12.5" 2 17" 5.00 3.75LD93272110S 11" 13.5" 2 18" 5.25 4.13LD93273120S 12" 14.5" 3 19" 4.38 2.87LD93273130S 13" 15.5" 3 20" 4.38 3.37LD93273140S 14" 16.5" 3 21" 4.68 3.57LD93273150S 15" 17.5" 3 22" 5.00 3.75LD93273160S 16" 18.5" 3 23" 5.25 4.00LD93274170S 17" 19.5" 4 24" 4.50 3.00LD93274180S 18" 20.5" 4 25" 4.50 3.50LD93274190S 19" 21.5" 4 26" 4.75 3.75LD93274200S 20" 22.5" 4 27" 5.00 4.00LD93274210S 21" 23.5" 4 28" 5.25 3.88LD93275220S 22" 24.5" 5 29" 4.50 3.25LD93275230S 23" 25.5" 5 30" 4.75 3.50LD93275240S 24" 26.6" 5 31" 5.00 3.75LD93275250S 25" 27.5" 5 32" 5.25 4.00LD93276260S 26" 28.5" 6 33" 4.38 3.30LD93276270S 27" 29.5" 6 34" 4.38 3.80LD93276280S 28" 30.5" 6 35" 4.68 3.55LD93276290S 29" 31.5" 6 36" 4.68 4.05LD93276300S 30" 32.5" 6 37" 5.00 3.75LD93276310S 31" 33.5" 6 38" 5.25 3.63LD93277320S 32" 34.5" 7 39" 4.38 4.11LD93277330S 33" 35.5" 7 40" 4.68 3.71LD93277340S 34" 36.5" 7 41" 5.00 3.25LD93277350S 35" 37.5" 7 42" 5.00 3.75LD93277360S 36" 38.5" 7 43" 5.25 3.50LD93277370S 37" 39.5" 7 44" 5.25 4.00LD93278380S 38" 40.5" 8 45" 4.68 3.87LD93278390S 39" 41.5" 8 46" 4.80 3.95LD93278400S 40" 42.5" 8 47" 5.00 3.75LD93278410S 41" 43.5" 8 48" 5.10 3.90LD93278420S 42" 44.5" 8 49" 5.25 3.88

Model LD-9327 spray lances described below include spray nozzles in which air under pressure atomizes lubricant from the valve panels and sprays it onto the gear face. Note that guard width must be exactly 3" wider than gear face width. Contact factory for special applications.

VIEW A-A

1.67"1.22"

6.7"8.0"

9.0"

7.75"

60°6.75"

4.25"

3.0"1.75"

4.75"

1.0"

5.75"

.625"

Ø.75"(X4)

NOTE: "S" series spray lances are shipped with round spray nozzles installed. Flat spray nozzle set is also included with each spray lance.


8

SC400 MULTI-FUNCTION CONTROLLER/MONITOR

GeneralThe SC400 Controller is a full featured lubrication control, offering “two plus one” functionality. The controller has the ability to operate a single pump and two zone valves (e.g. frequent/infrequent lubrication cycles) or two separate pumps (e.g. one oil pump & one grease pump). For single zone systems, the SC400 Controller also offers two intervals (e.g. weekday /weekend). The controller can activate a fi ll pump as needed to maintain proper fl uid levels in the oil or grease reservoir.

Technical Data

Input Voltage 85 to 265 VAC, 50/60 Hz

Output Rating (Line A & B) 8 amp (90 to 250 VAC)

Enclosure Rating IP-56

Idle Time Range 1 second to 100 days

Machine Cycle Counts 1 to 999,999 Counts (30 counts/second at 50% duty cycle)

Watchdog Timer 1 second to 60 minutes

Monitor Time 1 second to 24 hours

Cycle Counts On 1 to 999 counts

Over Counts 0 to 9

Net Weight 5 lb

Length x Width x Height 12.3” x 9.2” x 5”

Fault Relay Contacts 5 amp

Features + 2 zone operation (for Progressive, Injector and Dualine Hydraulic systems). + IP56 enclosure, constructed of molded polyester fi berglass. + CE approved. + Four supported languages (English, French, Spanish, German). + Pump output may be powered externally or via control power. + Valve A, Valve B and Fill pump may be powered exrternally or via controller. + Critical Inputs accept PNP, NPN or mechanical switches. + 500 mA of 24 VDC is available to power customer's accessories. + Primary alarm inputs may be programmed for N.O. or N.C. functionality. + Machine watchdog and cycle monitoring. + Pause (standby), jog (manual operation). + Accepts all BDI electric reversing valves and cycle/pressure/"end-of-line" switches. Refer to the following documents for more info:

+ Datasheet #35980: SC400 Controller


9

SYSTEM AIR REQUIREMENTS

A free air volume of Va cubic feet, calculated by the equation below, should be provided for each lube cycle. This is twice the theoretical air volume needed to operate both pump and nozzle. A lube cycle is defined on page 3.

0 50 100 150 2000

.10

.20

.30

.40

.50

.60

.70

.80

LENGTH OF DISTRIBUTION LINES IN FEET

LUBE

COM

PRES

SION

TIM

E “T

2” I

N M

INUT

ES

Fig. 10 - Lube compession time “T1”(based on 1% compressibility of lubricant).

1/2” PIPE3/4” PIPE

1” PIPE

1-1/4

” PIP

E

1-1/

2” P

IPE

*The pump is assumed to be operating with air pressure regulator set between 80 and 100 psi and a line back pressure of 1000 psi (the line back pressure is usually much lower). Lube volume discharged by the pump is assumed to be 40 cubic inches per minute.

Va = 2V1(T1+T2)+2V2(T1+T2+T3)

Where: V1 = Free air volume used by the pump*. assume = 5.0 cfm.

V2 = Free air volume used by the nozzles in cu.ft. per minute see Fig. 9.

T1 = Time in minutes to compress lube in distribution lines. see Fig. 10.

T2 = Time in minutes required by a pump to discharge lube from the nozzles during one count. See Fig. 9.

T3 = Time in minutes for air to clean lube from nozzles after discharge. Allow 0.50 minutes.

Example: Find the free air volume needed by the spray system shown in Fig.2. (Page 4) The lance has six U922C nozzles. The valve panel has six valves - DM62 valve blocks. Distribution lines consist of 100' of 1" pipe. The system is to be operated four times an hour.

Va = 2 x 5 (.18 + 0.09) + 2 x 81 (.18 + 0.09 + .5) = 127cu.ft. per lube cycle

Volume of free air required for one hour is: 4 x 127 = 508 cu.ft.

NO. OF NOZZLES

T2V2 (cfm)

FOR DD5X FOR DM6X1 .005 .015 13.52 .010 .030 27.03 .015 .045 40.54 .020 .060 54.05 .025 .075 67.56 .030 .090 81.07 .035 .105 94.58 .040 .120 108.0

Fig. 9 - Values for T2 and V2.


10

BDI SPRAY CONTROL VALVE & NOZZLE ASSEMBLIES

1

2”

1” 1”

3/8”11/16” TO CENTERLINEOF 1/4”NPTF LUBE UNIT

1/2”

1-3/

4”

2-3/

4”

3-27

/32”

1/2”

21/64”(X2)

1-3/8”

1-3/8”

1-3/32”

1”

1/2”

2

SC1-2 SPRAY CONTROL VALVE WITH U943 SPRAY NOZZLE SET-UP

ITEM # PART NO. DESCRIPTION*1 N/A Valve Body*2 N/A Piston3 SC110061 Spring-Piston Stop4 SC110072 Air Check Valve Assy.

**5N/A

Check Valve Body**6 Lock Nut**7 Spring**8 Quad Ring9 U204B6 5/16-18 x 1-3/4 Cap Scr.

10 U213F 5/16 Lockwasher11 U219B 5/16-18 Hex Nut12 U230D 5/16" Check Ball13 U943 Spray Nozzle Set Up14 U1204D 7/16-20 Dr. Ret. Scr.15 U1305G 7/16" Copper Washer16 U1522D Closure Plug17 U1526 Ball Retainer

*Items 1 & 2 shown for reference only - not for resale.**Items must be purchased in item#4.

1

12

13

8

17

14

6 4

7

5

3

2

15

16

19

20

18

21

APPLICATION: SC1-2 spray control valves are used on manually operated spray systems, automatic gear spray systems on shovels and drag lines, and on older gear spray panels.

COMPONENT ASSEMBLIES1. SC1 Series spray control valve (identical for all assemblies)

2. U943 spray nozzle setup (model selected depends on lubricant and application)

NOTE:SC1-2 spray control valve and U943 spray

nozzles are sold separately. Must purchase individually.

U-943 SPRAY NOZZLE SET-UP

ITEM PART NO. NAMEU943A U943C U943F

18 UX943A1 UX943C1 UX943C1 Fluid Nozzle19 UX943A2 UX943C2 UX943F2 Air Nozzle20 UX943A3 UX943A3 UX943A3 Hex Retainer21 UX943A4 UX943A4 UX943A4 Gasket

HOW TO ORDER EXAMPLES:A. Spray nozzle setup if known: One SC1-2 spray control valve with spray nozzle setup. (Specify correct spray nozzle setup, whether U943A, C or F.)B. SC1-2 w/After Blow: Order P.N. SPR13241B (Order U943 separately)C. Spray nozzle setup: 1. U943A - for light oil. 2. U943C - for oil or grease - recommended for most spray applications. 3. U943F - used when flat spray pattern is desired such as spraying wire rope.


11

BDI SPRAY CONTROL VALVE & NOZZLE ASSEMBLY

HOW TO ADJUST MODEL SC1 SPRAY CONTROL VALVES

SC1 valves are factory adjusted to function properly with NLGI #0 consistency lubricant. If other lubricants are used, the following adjustment may be needed to improve atomization or to eliminate nozzle burping at the start and end of the lube cycle.

1. Pump to 1000 psi on the pressure gauge. Relieve system with the pump solenoid valve and then loosen locknut (item 6, page 10) at the air inlet and turn check valve body (5) clockwise until air slows thru spray nozzle (13). Finally turn check valve body counterclockwise until no air escapes.

2. Repeat "1" several times if needed for good atomization. Then tighten locknut. Caution: To prevent a change in setting, hold check body firmly while tightening locknut.

HOW SPRAY CONTROL VALVE & NOZZLE ASSEMBLIES OPERATE

1. Lube under pressure fl ows thru port A into chamber B causing piston D to move toward ball E. this both unseats the ball and opens a port from chamber B to passage G.

2. Air fl ows past ball E thru passage F and lube fl ows thru passage G. They meet in air nozzle H and produce a spray. Removal of the air nozzle will only produce a more concentrated spray.

A

E

C

D

B

H

G

F

1/8” DIA. STEMTHIS END

ASSEMBLY NOTES

When assembling an SC1 valve, install large (1/8" dia.) end of piston D toward ball as shown in figure.

SCI PERFORMANCE DIAGNOSIS - (Valve fails to operate properly)

Cause Repair

1. Insuffi cient air supply. 1. Check pressure - should be 80psi minimum(not less than 60 psi during spray cycle)

2. Incorrect setting of air control valve. 2. Re-adjust - see above for details.

3. Clogged spray nozzle. 3. Wash with solvent and reassemble.

4. Clogged spray control. 4. Remove pilot piston and clean it and the piston bore with solvent. Reassemble.


12

SCI CONVERSION - TO PROVIDE AFTER BLOW

(FOR EXISTING SPRAY PANELS EQUIPPED WITH SC1 VALVES)

FIGURE - 14

AIR RELEASEVALVE BODY

JAMBNUT

AIR ENTRY PORTTO NOZZLE

AIR NOZZLE(MUST ORDERSEPARATELY)

HEXRETAINER

FLUID NOZZLE

LUBE CROSSPORTTO NOZZLE

STAINLESSSTEEL BODY

LUBRICANT

SOCKET SET SCREW5/16”-18 X 5/16” LG.(LOCTITE THREADS).257” DRILL5/16”-18 TAP

AIR

NOTESExisting spray panels equipped with SC1-2 spray control valves can be upgraded to incorporate after blow by employing the following procedure:

1. Remove items (shown on page 10) numbers 2, 3, 8, 12, 17, 7 and 14.

2. Drill piston bore .257" then tap 5/16"-18.

3. Insert 5/16"-18 x 5/16" long set screw coated with Loctite thread locker.

4. Insert solenoid air shut-off valve in air line to nozzles and wire in parallel with air operated barrel pump.

5. Install time delay relay in control circuit to provide approximately 60 seconds after blow.

CAN ORDER SC1-2 WITH AFTER BLOW FROM BDI. PART # SPR13241B. MUST ORDER AIR NOZZLE SEPARATELY(SEE PG 10)


13

INSTALLATION INSTRUCTIONS

INSTALLATION

1. Pump Close To Valve Panel (See Page 3): In most installations of this type, hoses are used to make all air and lubricant connections. Hose lengths must be adequate to allow movement of the pump during lubricant drum changes. Clean inside of hoses thoroughly before installing to remove foreign material. Tighten all hose connections securely using a thread lubricant and sealant.

2. Pump Remote From Valve Panel (See Page 4): Hoses are used to connect the air line to the pump and the pump to the reversing valve. Pipe is run from the reversing valve to within 30" of the valve panel with the final connection to the valve panel made with hose assemblies.

Pipe size selection is important, as it will affect the operating pressure of the system. For guidance in selecting proper pipe size, see pipe sizing table in Figure 15.

Pipe Sizing Table - Fig. 15(Pump Remote From Valve Panel)

PIPE SIZEOPERATING TEMPERATURE (°F)

50° - 90° 32° - 50° 0° - 32°

1/2 60 FT. 40 FT. 20 FT.

3/4 - 60 FT. 30 FT.

1 - - 40 FT.

NOTE: Longer lengths and larger diameter pipe is not recommended due to the fact that the compressed volume of lubricant, within a pipe, causes the valve manifold to cycle after the pump shuts down. This can result in excessive consumption of lubricant and/or cause the SC400 control to fault.

Clean pip thorougly before installation to remove all scale, chips, dirt and burrs. Install pipe in protected locations and firmly clamp in place. Pipe threads should be cut clean and free of burrs. Use a good thread lubricant and sealant. Use 3000 pound forged steel fittings and schedule 80 pipe. Pull all connections tight.

3. For valve panel and spray lance locations - see page 14.

4. The Lubricant: High quality open gear lubricants are readily available that can be pumped and sprayed at low temperatures without requiring heat. Be sure that the lubricant selected will remain pumpable at the minimum operating temperature that will be encountered.


14

INSTALLATION & LAYOUT

INSTALLATIONLOCATION FOR VALVE PANEL LD12361 AND SPRAY LANCES LD9327 AS SHOWN IN FIGS. 16 & 17.

FIGURE - 17

FIGURE - 16

ANGLE OFSPRAY

GEAR

30° +/- 10°

8” +/- 1/2”

GEAR GUARD

GEAR PITCH CIRCLE

GEAR GUARDSPRAY LANCE LD9327

SPRAY LANCE LD9327

PITCH CIRCLE - GEAR

GEAR TOOTHCENTERLINE

PITCH CIRCLE - PINION

GEAR GUARD

SPRAYPATTERNCENTERLINE

SPRAY LANCE LD9327GEAR GUARD

8” +/- 1/2”

CENTERLINESPRAYPATTERN

30° +/- 10°30° +/- 10°

1-7/32”

1-7/32”8” +/- 1/2”


15

START UP AND MAINTENANCE

START UP PROCEDURE

1. Program the SC400 controller in accordance with instructions given.

2. Fill air line lubricator with light oil (SAE #10).

3. Adjust pump air regulator to obtain 1800 psi pump line pressure.

4. The DR4 reversing valve is set to reverse at 1500 psi at the factory.

5. Set the air regulator for the spray nozzles to 60 - 80 psi. Re-adjust for best spray.

6. To fi ll the two main supply lines to the measuring valves:a) Remove the pipe plugs from the last measuring valve.b) Start pump by pressing SC400 manual/reset button.c) Bleed (1) pint of lubrication from line 1 at the last measuring valve.d) Stop pump by pressing SC400 manual/reset button again.e) Insert pipe plug in last measuring valve (line that was purged).f) Start the pump again. Pressure will build up to operate the reversing valve.g) Follow steps c, d, and e for purging supply line 2.

7. After purging both suply lines, the system is ready to operate. Cycle the system manually until the spray nozzles are operating properly and the gear face is being completly covered with lubricant.

8. Coat the entire gear face (all teeth) with lubricant before starting up the mill.

MAINTENANCE

A. Too much water in the air fi lter drain bowl on the air control panel will make the fi lter ineffective and water will enter the pump. Empty it regularly, a drain cock is provided. If moisture in the air supply line requires fre-quent draining of the air fi lter we suggest installing automatic drain assembly.

B. Be sure lube container has plenty of lubricant. Pumping from an empty drum may force air into system, caus-ing diffi culty in building pressure.

C. Use clean lubricant. Foreign matter might clog valve manifold.

D. Keep line stainers clean. These are usually installed in the line leading to the valve manifold. Establish regular intervals for this service.

E. Inspect entire system regularly including hose (replace if damaged), connections (they should be tight), and the gear (see that the teeth are being properly lubricated). Check spray pattern frequently by inserting a piece of cardboard in front of the spray nozzles while the system is operating. Complete coverage of the gear face is important.

F. Completely clean the system with a fl ushing solvent every year or two to extend its life.


16

TROUBLE SHOOTING

SYSTEM DIAGNOSIS

CONDITION CAUSE REMEDY

A. Pump doesn't operate*

1. Insuffi cient air supply. 1. Adjust air pressure to 40/50 psi.

2. Timer control failing to operate solenoid shut-off.

2. Check wiring of system timer ac-cording to instructions and SC400 controller. Also check timer for proper programming.

3. Lubricant has hardened in drum.3. Use smaller sized drums - diluent in some lubricants tends to evaporate causing lubricant to harden.

B. Pump operates but doesn't build pressure.

1. Reservoir empty.1. Check and renew lubricant supply. Purge air from lines.

2. Broken line. 2. Repair or replace as necessary.

3. Air in system.3. Bleed lines and valves as described on page 15.

C. Manifold valve indicator doesn't operate.

1. Lack of pressure. 1. Repair - see condition B.

2. Incorrect operation of reversing valve..

2. Check valve condition by "short-circuiting" it with two 3/8" pipe plugs installed in reversing valve discharge ports. Start air-operated barrel pump, and reversing valve will oscil-late if properly adjusted for type of system. Clean any strainer in lines every six months.

3. Dirt in Dualine measuring valve. 3. Remove inlet bore plugs and piston. Clean bore by pouring solvent through it. Clean piston and re-assemble.

4. Plugged discharge line.4. Locate obstruction, remove line and blow clean, or replace faulty sec-tion.

*For more information on the air operated barrel pump, see Data Sheet # 35993.


17

Notes


18

Notes


19

Notes

Whatever your automatic lube requirement…

We have the solution!

BDI has been a manufacturer of automatic lubricating systems for over 80 years. We offer a complete line of pumps, valves, controllers, and accessories. Our pump line includes manual, air, electric, and hydraulic actuated models. Our valve offering is the most comprehensive in the industry. We manufacture oil and grease Dualine valves, series progressive modular valves, and injectors. We also offer air/oil mixing modules, oil flow meters, and single point lubricators.

DL3100-R3 (05/16)

Series Progressive

Dualine

Injectors

Flowmeters

RefillableSingle Point

SureFire-PDIOil Recovery Unit

BIJUR DELIMON INTERNATIONAL2685 Airport Road • Kinston, NC 28504Tel. 800-227-1063 • Fax: 252-527-9232

Website: www.bijurdelimon.com

BIJUR® DELIMON®-DENCO FARVAL® LUBESITE®

ReSin

Your local distributor:

Let 80+ Years Of Experience Design Your Next Lube System

Operators Manual DL3100 - Bijur Delimon

Documents

Transcript of Operators Manual DL3100 - Bijur Delimon