Operator’s Maintenance Manual - Boat Service HaarlemOperator’s Maintenance Manual CALIFORNIA –...
Transcript of Operator’s Maintenance Manual - Boat Service HaarlemOperator’s Maintenance Manual CALIFORNIA –...
Operator’s Maintenance
Manual
CALIFORNIA – Proposition 65 Warning: Diesel engine exhaust and some of its constituents are known tothe state of California to cause cancer, birth defects and other reproductive harm.
Heat
Exchanger
and Keel CooledSmall Diesel Engine Range: Beta 10,
BZ482, Beta 16, BD722 & Beta 25
Engine Details
Engine Type: Power: bhp Speed: rpm
BETA WOC NO: K Engine Serial No:
Gearbox Type: Serial No: Ratio :1
Purchased from:
Invoice No: Date:
Date Commissioned:
Specification / Special Details
IMPORTANT – Please fill in details at moment of purchase – it really will help you! (and it will really help us specify the correct spare parts for you).
1
INTRODUCTION 2Engine Identification 2
Initial Receipt of the engine 2
Engine Storage 2
SAFETY PRECAUTIONS 3
TECHNICAL SPECIFICATIONS 4
SECTION 1: GUIDELINES FOR OPERATION OF ENGINE
Important checks prior to initial use 5
Initial Start-up and Bleeding The Fuel System 5
Starting/Stopping 6
SECTION 2: MAINTENANCE AND SERVICE GUIDELINES
Maintenance Schedule: 7
Lubrication – Checking and changing oil 8
Fuel System - Pumps, Filter, fuel/water separator 9
Cooling - Fresh water system, Keel Cooling, Heat Exchanger 10
Sea Water Pump, Heat Exchanger 12
Belt Tensioning 13
Air Filter 13
Electrical 14
Laying up - Winterising 14
Troubleshooting 15
Torque Settings 26
SECTION 3: INSTALLATION GUIDELINES
Engine Mounting 27
Alignment - Drives, Flanges, Flexible Drives 27
Exhausts & Bends 28
Mounting Exhausts 28
Fuel Supply 29
Cooling 30
Calorifier System 31
Electrical installations 32
Appendices –wiring diagrams and general arrangements 32
Component identification at rear of manual. 63
Maintenance Record 65
Contents
ENGINE IDENTIFICATION
NOTE: In all communications withthe distributor or Beta Marine, theengine number, type, and W.O.C.number must be quoted.
BETA 10, BZ482, BETA 16,BD722 & BETA 25
The engine serial number is stampedabove the fuel lift pump on thestarboard side of the engine, and isshown on the rocker cover label.
INITIAL RECEIPT OF THE ENGINEA full inspection of the engine mustbe made immediately on delivery toconfirm that there is no damage. Ifthere is any damage then write thisclearly on the delivery note andinform your dealer or Beta Marinewithin 24 hours.
ENGINE STORAGEThe engine must be stored in a dry,frost free area and this is best done inits packing case. If storage is to bemore than six months then theengine must be inhibited (contactyour dealer or Beta Marine). Failureto inhibit the engine may result in theformation of rust in the injectionsystem and the engine bores, thiscould invalidate the warranty.
OPERATION AND MAINTENANCE MANUAL FOR THE FOLLOWING BETA MARINE ENGINES BASED ON KUBOTA MINI SERIES
Beta 10, BZ482, Beta 16 (BZ602),BD722 & Beta 25 (BD902)
2
This manual has been compiled toprovide the user with importantinformation and recommendationsto ensure a trouble free andeconomical operation of theengine.
For further advice or technicalassistance, application should bemade to BETA MARINE LIMITEDor its distributors.
All information andrecommendations given in thispublication are based on the latestinformation available at the time ofpublication, and are subject toalteration at any time. Theinformation given is subject to thecompany’s current conditions ofTender and Sale, is for theassistance of users, and is basedupon results obtained from tests
carried out at the place ofmanufacture and in vessels usedfor development purposes. We donot guarantee the same results willbe obtained elsewhere underdifferent conditions.
SAMPLE
3
A Keep the engine, gearboxand surrounding area clean,including the area immediatelybelow the engine
B DRIVES - Power Take OffAreas
i) Gearbox Output Flange
The purpose of a marine dieselpropulsion engine is to providemotive power to propel a vessel.Accordingly the gearbox outputshaft rotates at between 300 and2400 rev/min. This flange isdesigned to be coupled to apropeller shaft by the installer andsteps must be taken to ensureadequate guarding.
ii) Forward End Drive
Engines are supplied withunguarded vee belt drives topower the fresh water pump andbattery charging alternator. Theinstaller must ensure that it is notpossible for injury to occur byallowing accessibility to this areaof the engine. The three pulleysrun at high speed and can causeinjury if personnel or clothingcome in contact with the belts orpulleys, when the engine isrunning.
iii) Power Take Off Shaft (Engine Mounted Option)
Shaft extensions are available asan option and rotate at between850 and 3600 rev/min. Ifcontact is made with this shaftwhen the engine is running, injurycan occur.
C EXHAUST OUTLET
Diesel marine propulsion enginesemit exhaust gases at very hightemperatures - around 400-500°C. Engines are supplied witheither wet exhaust outlet (waterinjection bend) or dry outlet (dryexhaust stub) - see option list. At
the outlet next to the heatexchanger/header tank, theexhaust outlet can become veryhot and if touched, can injure.This must be lagged or avoided byensuring adequate guarding. It isthe responsibility of the installer tolag the exhaust system if a drysystem is used. Exhaust gasesare harmful if ingested, theinstaller must therefore ensure thatexhaust lines are lead overboardand that leakage in the vesseldoes not occur.
D FUEL
i) Fuel Lines
Diesel engines are equipped withhigh pressure fuel injectionpumps, if leakages occur, or ifpipes fracture, fuel at a highpressure can harm personnel.Skin must be thoroughly cleanedin the event of contact with dieselfuel.
ii) Fuel Supply Connections
Engines are supplied with 8 mmcompression fittings. The installermust ensure that whenconnections are made, they areclean and free of leaks.
E OIL
The Beta propulsion is suppliedwith 2 dipsticks, one for theengine and one for the gearbox.Ensure dipsticks are returned andsecure after checking, if not oilleaks can cause infection whentouched. All oil must be removedfrom the skin to prevent infection.
F SCALDING
An engine running under load willhave a closed circuit fresh watertemperature of 85° to 95°C. Thepressure cap on the top of theheat exchanger must not beremoved when the engine isrunning. It can only be removedwhen the engine is stopped andhas cooled down.
G TRANSPORTATION/LIFTING
Engines are supplied ontransportable pallets. Lifting eyeson engines are used for liftingengine and gearbox assemblyonly, not the pallet andassociated kit.
GENERAL DECLARATION
This machinery is not intended tobe put into service until it has beenincorporated into or with othermachinery. It is the responsibility ofthe purchaser/installer/owner, toensure that the machinery isproperly guarded and that allnecessary health and safetyrequirements, in accordance withthe laws of the relevant country, aremet before it is put into service.
Signed:
J A Growcoot, C.E.O, Beta Marine Limited
NOTE: Recreational Craft
Where applicable, thepurchaser/installer/owner and operatormust be responsible for making surethat the Recreational Craft Directive94/25/EC is complied with.
SAFETY PRECAUTIONS!
TEC
HN
ICA
L SP
EC
IFIC
ATIO
NS
MIN
I SE
RIE
S –
STA
ND
AR
D
EN
GIN
ES
Max
imum
Ang
le o
f Ins
talla
tion:
Trim
15°
, Rol
l 30°
(inte
rmitt
ent)
Rot
atio
n:AN
TI C
LOCK
ON
FLY
WH
EEL,
CLO
CKW
ISE
ON
OU
TPU
T G
EARB
OX
FLAN
GE
FOR
USE
WIT
H R
IGH
T H
AND
PR
OP
IN A
HEA
DD
iese
l fue
l mus
t con
form
to B
S286
9-19
70 c
lass
A1
or A
2.
The
fuel
mus
t be
a di
still
ate,
and
not
a r
esid
ual o
il or
ble
nd.
Lubr
ican
t:En
gine
- En
gine
oil
mus
t mee
t MIL
-L-2
104C
(see
sec
tion
2 fo
r det
ails
)G
earb
ox -
see
oper
ator
’s m
anua
l for
the
gear
box
oil t
ype
and
capa
city
Oil
pres
sure
– m
inim
um (t
icko
ver)
0.5
bar
Pow
er o
utpu
ts: T
hese
com
ply
with
BS
EN IS
O 8
665:
1996
cra
nksh
aft p
ower
Not
e: D
ecla
red
Pow
ers
to IS
O86
65:1
995
1. T
he d
ecla
red
pow
ers
are
at th
e sa
me
engi
ne s
peed
as
the
ISO
304
6 fig
ures
. Thi
s sp
eed
is th
e sp
eed
rela
ted
to th
e ou
tput
s / p
ower
s sh
own.
2. D
ecla
red
pow
ers
are
at th
e ge
arbo
x co
uplin
g (c
oupl
ing
to th
e pr
opel
ler s
haft)
as
per c
laus
e 3.
2.1
with
sta
ndar
d sp
ecifi
catio
ns a
s pe
r our
cur
rent
pric
e lis
ts.
Addi
tiona
l acc
esso
ries
or a
ltern
ativ
e ge
arbo
xes
may
affe
ct th
e de
clar
ed p
ower
s.3.
Ope
ratio
n at
par
amet
ers
outs
ide
the
test
par
amet
ers
may
affe
ct th
e ou
tput
s / p
ower
s w
hich
in a
ny c
ase
are
subj
ect t
o th
e IS
O to
lera
nce
band
s.
4
BET
A 10
B
Z482
B
eta
16
BD
722
Bet
a 25
Cylin
der
2 2
23
3B
ore
(mm
) 67
6772
67
72
Stro
ke (m
m)
68
6873
.6
68
73.6
Dis
plac
emen
t (cc
)47
947
959
971
989
8Co
mbu
stio
n 3
Vorte
x E-
TVCS
Cool
ing
Wat
erSt
arte
r vo
ltage
(V)
12St
arte
r ou
tput
(kW
)0.
8St
arte
r al
tern
ator
out
put (
Amps
) 40
(sta
ndar
d)G
low
plu
g re
sist
ance
(eac
h)
1ΩEn
gine
spe
ed (R
PM)
3,00
0 3,
600
Pow
er o
utpu
t to
ISO
3046
(BH
P)
10.0
13.3
16.7
20.0
24.8
Dec
lare
d po
wer
ISO
8665
(kW
) 7.
48.
711
.013
.116
.3Fu
el ti
min
g B
TDC
21°
Capa
city
of s
tand
ard
sum
p ap
prox
(litr
es)
2.0
- 2.5
2.4
- 2.9
3.1
- 3.8
3.7
– 4.
5Ca
paci
ty o
f sha
llow
sum
p ap
prox
(litr
es)
2.2
2.6
3.4
3.8
Net
t dry
wei
ght w
ith g
earb
ox (k
g)
87.2
94
.1
101.
7 11
0.6
Fuel
D
iese
l oil
clas
s A1
/ A2
Cool
ant
33%
-50%
max
imum
ant
ifree
ze /
wat
erCo
olan
t cap
acity
app
rox
(H/E
litr
es)
2.25
3.
00
3.25
Min
. rec
omm
ende
d ba
ttery
cap
acity
12V,
40A
h 12
V, 7
5Ah
INITIAL STARTUP ANDBLEEDING THE SYSTEM(a) Open fuel bleed screw on
injection pump by 11/2 turns. Seediagram 1a.
(b) Move hand priming lever on fuellift pump up and down until fuelwith no bubbles comes out of thebleed screw.
(c) Shut/tighten the bleed screw.Clean area thoroughly with tissuepaper.
(d) Continue to hand prime for 30seconds to push fuel through thefuel pump.
(e) Start engine (see normal starting).
Note the engine may have to beturned over with the starter for afew seconds before it fires. Donot run the starter for more than20 seconds. If the engine has notstarted after 20 seconds thendisengage the starter andcontinue to hand prime for afurther 30 seconds, then repeat.
(f) If engine does not start after 3attempts then allow 5 minutes forthe starter to cool down beforerepeating (a) to (e).
Note: The starter windings canbe burnt out with continuouscranking
CAUTION
To avoid personal injury:• Do not bleed a hot engine as this
could cause fuel to spill onto a hotexhaust manifold creating a dangerof fire.
• Do not mix gasoline or alcoholwith diesel fuel. This mixture cancause an explosion.
• Do not get diesel on the flexiblemounts – they will deterioraterapidly if soaked in diesel.
• All fuel must be removed from skinto prevent infection.
5
Diagram 1a
SECTION 1GUIDELINES FOR OPERATION OF ENGINE
IMPORTANT CHECKS PRIORTO INITIAL USE1. Generally, a new engine has the
oil and anti-freeze removed afterthe works test. Fill the enginewith the correct oil and anti-freeze (see sections on ENGINEOIL and COOLING). Checkgearbox oil level - see separateoperator’s hand book.
2. Ensure the engine is free to turnwithout obstructions.
3. Ensure battery is fully chargedand connected (the isolator is in
the ‘ON’ position).
4. Ensure Morse speed and gearboxcables are fitted correctly and thatcable travel lengths are correct.Gear selection lever –allmechanical gearboxes: care mustbe taken to ensure that theremote control cable is adjustedso that the selector lever on thegearbox moves FULL travel andbrought “hard up” against its endstop in both directions. Failure toachieve the correct adjustmentwill reduce efficiency of theclutch and may cause slippage at
low revs. Warranty will not beaccepted on gearboxes returnedin the warranty period for failuredue to incorrect adjustment.
5. Ensure engine is out of gear with1/3 throttle - see single levercontrol instruction manual.
6. Open the fuel stopcock and bleedthe fuel water separator of air asshown in manufacturersliterature.
7. Fuel should now be at the fuel liftpump, see diagram 1a.
8. Open the sea cock.
6
STOPPINGEvery propulsion engine is fitted with astop solenoid which is energised tostop. To stop engine simply press stoppush button, hold in until enginestops, then turn key from ‘RUN’ to‘OFF’ position.
When leaving the boat for an extendedperiod,• Turn off sea-cock (heat exchanger
cooled engines).• Turn off battery isolator.Do not turn the key to the offposition when the engine is running.This will not allow the alternator tocharge.*WARNINGDo not leave the key in ‘HEAT’ positionfor more than 15 seconds - this willdamage the heater plugs and eventuallylead to poor starting.
Do not depress stop button for morethan 10 seconds as this will lead tooverheating and failure of the solenoid.
NOTES FOR ALL PANEL TYPES:
Do not depress the stop button formore than ten seconds as this willlead to overheating and failure of thesolenoid.
The Mini range of engines areequipped with a mechanical stop leverin the event of electrical system failure.This lever is located on the starboardside of the engine above the speedcontrol lever. See illustration below:
Stop leverStop lever
Speed leverSpeed lever
NORMAL STARTING (ALL BETAPANELS WITH SILVER KEYSWITCH)
With the engine out of gear, set speedcontrol lever to 1/3 throttle. Turn keyanti-clockwise to HEAT* (A) positionand hold for ten seconds, turn keyclockwise to RUN (C) position. At thisstage the instrument panel shouldilluminate, an alarm buzzer will soundand two (or three*) red warning lightswill illuminate:
STARTER BATTERY CHARGE
DOMESTIC BATTERY CHARGE* (Din battery symbol - AB & C PANELSONLY)
*(Note: this will only illuminate if 2ndalternator is fitted)
OIL PRESSURE and green POWERON / RUN LIGHT (this will stay on)
Turn to START(D) position andengine willmotor, hold inposition untilengine fires (seeinitial start-upsection for maximum time starter canbe used).
Release key (when engine has started)to RUN position. Ensure alarm buzzeris not sounding and that warninglights are extinguished. If one or bothof the alternator warning lights are stillon, then increase engine speed toexcite the alternator - then return toidle. The battery charge lights shouldthen go out. The run light will remainon (green LED).
Note: for panels without keyswitchessee seperate instruction sheet (page 24).
RUNC
STARTD
OFFB
HEATA
7
SECTION 2MAINTENANCE SCHEDULE
DAILY OR EVERY 8 HOURSRUNNING
• Check engine oil level.• Check gearbox oil level.• Check coolant level.• Check battery fluid.• Check drive belt tension• Ensure raw water inlet strainer is
clear.• Check stern gland lubrication.• Drain off any water in fuel water
separator.
AFTER THE FIRST 25 HOURSRUNNING
• Change gearbox lubricant (Seeseparate gearbox manual).
• Check that all external nuts, boltsand fastenings are tight. See tablefor torque values. Special attentionshould be paid to the flexiblemount lock nuts, these should bechecked for tightness, startingwith lower nut first in each case.If the lower nuts are found to bevery loose, then the alignment ofthe shaft to the gearbox halfcoupling should be re-checked.Poor alignment due to looseflexible mount nuts will causeexcessive vibration and knocking.
• Check the belt tension on anysecond alternators fitted andadjust –see page 11
• Check ball joint nyloc nuts fortightness on both gearbox andspeed control levers. Grease bothfittings all over.
AFTER FIRST 50 HOURS
• Change engine lubricating oil.
• Change oil filter.
• Check for leaks on header tanktubestack. Tighten end cap bolt ifrequired.
• Drain off any water in fuel/waterseparator.
EVERY 150 HOURS
• If shallow sump (option) is fitted,change engine lubricating oil andfilter.
EVERY YEAR -OR EVERY 250HOURS IF SOONER
• Change engine lubricating oil(standard sump)
• Change lubricating oil filter • Check air cleaner element• Check sea water pump impeller
and change if worn.• Check wasting anode condition,
replace when necessary. In someenvironments this may be 6montly or less.
• Remove heat exchanger tubestack, by undoing the bolt eachend of the tube stack. Removeend cover, pull out tube stack andclean. Replace rubber ‘O’ ringsand re-assemble. Immediatelyengine is started check for leaks.
• Spray the key switch with WD40or equivalent to lubricate thebarrel.
• Check that all external nuts, boltsand fastenings are tight. See tablefor torque values.
• Check ball joint nyloc nuts fortightness on both gearbox andspeed control levers. Grease bothfittings all over.
EVERY 750 HOURS
• As every 250 hours plus thefollowing:-
• Change air cleaner element.• Change fuel filter.• Change antifreeze.• Change gearbox oil.• Check electrical equipment,
condition of hoses and belts,replace as necessary.
8
Engine oil: Engine oil should be MIL-L-2104C or have properties of APIclassification CC/CD/CE grades. Thefollowing table gives grades of oilrequired for various ambienttemperatures.
Note: A good quality 15W/40mineral or multigrade oil as used inmost diesel car engines will meetthese requirements. Do not use‘Turbo Diesel Oil’ or additives.
CHECKING ENGINE OILLEVEL
For quantities of oil required seesection marked ‘TechnicalSpecification’, Page 4When checking the engine oil level,do so before starting, or more thanfive minutes after stopping.
1. To check the oil level, draw outthe dipstick, wipe it clean, re-insert it, and draw it out again.Check to see that the oil level liesbetween the two notches.
2. If the level is too low, add new oilto the specified level - Do notoverfill,
IMPORTANT
When using an oil of different makeor viscosity from the previous one,drain old oil. Never mix two differenttypes of oil. Engine oil should bechanged after first 50 hours runningtime and then every year or every250 hours if sooner. Oil filter is acartridge type mounted on the portside of the engine.
(1) Run the engine for 10 minutes towarm up the oil.
(2) Your engine is provided with asump drain pump (option onBeta Ten, see note below).Unscrew the end cap on theend of the pump (if fitted),turn the tap to ‘on’. Use thehand pump as shown topump out the oil into abucket. Turn the tap to offposition and replace endcap. See diagram 2c.
(3) Unscrew the oil filter andreplace with a new one. Seediagram 2d.
Note: It is best to have aplastic bag wrapped roundthe filter to catch any oil leftin the system. (Always keepyour bilges clean!) Beforescrewing in the new filterspread a thin film of oilround the rubber gasket toensure a good seal andscrew in – hand tight.
Note: On the Beta Ten not fitted witha sump drain pump the engine oilmust be drained off by unscrewingthe sump drain plug (see diagram100-00030 at rear of book). This is
best done with the oil filler capremoved. Replace the plug andtighten firmly.
(4) Fill the engine with new oil asdescribed above.
LUBRICATION
AMBIENT TEMP SINGLE GRADE MULTI GRADE
-30°C TO 00°°CC SAE 10W S AE 10W/30
-15°C TO +15°C SAE 20W SAE 15W/40
0°C TO +30°C SAE 30 SAE 15W/40
25°C AND ABOVE SAE 30 SAE 15W/40
CHANGING ENGINE OIL
Fig. 2b. Dip stick
Fig. 2a
Oil goes in here Sump pump
Tap
Oil filter
End CapFig. 2c
Fig. 2d
9
Gearbox Lubricant Capacity (approx)
TMC40 Use ATF Oil 0.2 litres
PRM 80/ 120 Use Engine Oil 15W40 0.6 / 0.8 litres
ZF5M / ZF10M Use ATF Oil 0.3 / 0.35 litres
TTMC 35A-2 Use Engine Oil SAE 30 (HD) 0.65 litres
Note: ATF is Automatic Transmission Fluid
Fig 2e
Dipstick
Oil drainplug
Oilfillerplug
CHECKING GEARBOX OIL LEVEL
(1) The gearbox is fitted with adipstick and oil filler plug, see fig2e.
(2) Each engine is supplied with agearbox operators manual whichspecifies the type of lubricatingoil to be used, the capacity andfrequency of changing of the oil.
(3) New engines are normallysupplied with the gearbox topped up with lubricant butCheck the level before starting the engine for the firsttime.
(4) The oil can be changed via thedrain plug at the bottom of the
box or sucked out with a handpump via the filler plug.
(5) A guide to the type of oil to beused is as follows:
IMPORTANT
• Always fit a fuel/water separatorin the fuel supply system. Waterin the fuel can seriously damagethe injection system.
• If a fuel supply shutoff valve isfitted do not use a taper tap, onlyuse a ball valve tap. The ballvalve type are more reliable andless likely to let air into the fuelsystem.
• Be sure to use a strainer whenfilling the fuel tank. Dirt or sandin the fuel may cause trouble inthe fuel injection pump.
• Always use diesel fuel.
• Do not use kerosene which isvery low in cetane rating, andadversely affects the engine.
• Be careful not to let the fuel tankbecome empty, or air can enterthe fuel system, necessitatingbleeding before next engine start.
• The fuel lift pump will only liftfuel through 0.25 metres. If thisis insufficient then an electric fuellift pump must be fitted.
FUEL FILTER REPLACEMENT
1. The fuel filter is a spin on type.Remove by turning anti-clockwisewhen viewed from below.
2. Replace the fuel filter cartridgeevery 750 hours. See fig. 2g.
3. Apply fuel oil thinly over thegasket and tighten into position -hand tight.
4. Bleed as detailed - see initial start up.5. Check for leaks.6. Do not get fuel on the flexible
mounts.
FUEL SYSTEM (see page 29 for a typical installation)
Fuel filter
Filter bleed screw
Fig. 2g
10
Keel Cooled -Note efficient cooling tanks are sidemounted, see page 31
COOLING
The Mini Series range of engines arenormally fresh water cooled. Thiswater circulates through the engineand on to a heat exchanger where itis cooled by sea water which ispumped through the cooling tubes.The sea water is then injected intothe exhaust system (see diagram‘heat exchanger cooled’ below).
KEEL COOLING is an option. In thissystem the freshwater is pumpedthrough the engine and then througha cooler built into the side of the boatwhere it is cooled by heat transferbefore returning to the engine .
The ideal keel cooling tank shouldhave:
a. Baffle continuously welded toouter skin and close fitting oninner skin
b. Be thin in section to allow goodmixing of the water over the coolouter surface.
c. Air bleed valves should be fittedon both ends. (See page 30).
FILLING THE FRESHWATER SYSTEM
New engines are supplied with thefreshwater drained off. The followinginstructions must be followed to fillthe system.
(a) Mix up in a clean bucket a 30 to50% antifreeze to freshwatersolution. For the volume requiredsee technical specification page 4.
(b) Check that the drain tap or plugis turned off. (see fig 2l) (NoteBZ482 and B10 engines withsump drain pump are fitted witha plug).
(c) Fill engine with freshwater/antifreeze solution through the top ofthe heat exchanger or headertank with the filler cap removed.(see fig 2m).
(d) Fill header tank to the top of thefiller neck and replace cap. Press
down firmly on filler cap andhand tighten in a clockwisedirection.
Note: For keel cooled engines amuch larger quantity offreshwater/anti-freeze solution isrequired depending on the size of thekeel cooling tank – refer to thebuilder.
(e) Run the engine for 5 minutes onno load (out of gear) and checkcoolant level. Top up asnecessary.
(f) Check system for leaks.
Note: For keel cooled engines itis very important to bleed all theair out of the system before theengine is run on load (check withbuilder’s instructions).
(g) If a calorifier is fitted care mustbe taken to see that this is alsofull of coolant and all the air isexpelled. (See calorifier fittingnotes under Section 3).
(h) Run the engine on one third loadfor 15 minutes, preferably withthe boat tied up. As the systemwarms up coolant may beexpelled from the overflow pipeinto the bilge. Stop the engineand allow the engine to cooldown before removing thepressure cap and top up thecoolant to 1” below the fillerneck.
Heat Exchanger Cooled
11
Fig. 2m
YACHTS AND LAUNCHESWITH HEAT EXCHANGERCOOLING
It is essential that a 33% to 50%anti-freeze/water mixture is used.This not only stops freezing up inwinter, but it prevents overheatingand corrosion.
The warranty is invalid unless thecorrect ratio is used.
CANAL BOATS WITH KEELCOOLER A 33% anti-freeze to water mixture isrecommended to give protectionagainst very cold winter temperature ofminus 15°C. This anti-freeze will alsogive the engine internal protectionagainst corrosion. For keel cooledengines the total system capacity mustbe taken into consideration, ie enginevolume plus skin tank/keel coolervolume.
Concentration of ethylene should notexceed 50%.
The anti-freeze in the fresh watersystem enables the boiling point ofwater to rise to 124°C with a 13 psipressure cap fitted. The watertemperature alarm switch will howeverbe activated at 95° to 100°C. If noanti-freeze or a very weak solution isused, then the water temperatureswitch may not be activated beforecoolant is lost.
IMPORTANT
Removal of the pressure cap whenthe engine is hot can cause severeinjury from scalding hot water underpressure. Always allow the engine tocool and then use a large cloth whenturning the cap anti-clockwise to thestop. This allows the pressure to bereleased. Press firmly down on thecap and continue to turnanticlockwise to release the cap.
(i) Repeat (h) ifcoolant level is more than 1 inchbelow the base of the filler neckwhen the engine has cooleddown.
(j) Run engine on 2/3 full load for20 minutes, check for leaks andrepeat (i).
(k) Anti-freeze solutions should bedrained off every 2 years andreplaced with a new solution.
Note: When draining fresh watersystem, ensure the engine has cooledsufficiently to prevent scalding fromhot pressurised water. Prior todraining a cold engine, remove thefiller cap from the header tank andthen open the water drain tap. Thisallows the water to drain freely fromthe system.
Fig. 2l
Fig. 2k
12
SEA WATER PUMP AND COOLING SYSTEM - (Heat exchanger-cooled engines)
CAUTION
Before working on the sea watersystem ensure that the sea cock isin the off position.
(1) It is very important that thecorrect sea water flow ismaintained to cool the closedcircuit system of the engine. Thekey component in this system isthe sea water pump impeller.This should be checked everyyear by removing the circularplate (see fig. 2h)
(2) Withdraw the rubber impellerfrom its drive shaft as shown.See diagram 2i.
(3) Check impeller for cracks in therubber, excessive wear or lostvanes. Replace with a newimpeller as necessary.
Note: If any pieces of rubberimpeller are missing then they mustbe found as they are most likely to betrapped in the entrance to the heatexchanger cooling stack. See‘Cleaning Tube Stack’.
Fig. 2h
CLEANING THE HEAT EXCHANGER TUBE STACK AND REPLACING WASTING ZINC ANODE
(1) The wasting zinc anode shouldbe checked every six months andreplaced every year or asnecessary. The anode is attachedto the bolt inserted in the aft endcap of the heat exchanger. Seefig. 2j.
(2) Unscrew the bolt and replace thecomplete unit with a new one.
(3) Check for leaks.
(4) It is possible for fine sea weedand other debris to get past theinlet filter and into the tube stack.This should be removed andcleaned. See fig. 2k.
(5) Drain off coolant into a bucket.
(6) Unscrew the 2 end cap retainingbolts (one each end of the tubestack). Remove the ‘O’ rings andpull out tube stack. Clean tubestack and end caps.
(7) Re-assemble using new ‘O’ rings.Do not overtighten end cap boltsand make sure the tube stack isthe right way round.
(8) Re-fill engine with water/anti-freeze solution and run engine upto temperature to check for leaks.
Fig. 2jZincAnode
Fig. 2i
13
AIR INTAKE FILTERThese engines are fitted with an air intake filter which should be checked every season and changed every 2 years orsooner if badly clogged.
1 32
WARNING
Belt tension must only be checkedwith the engine switched off.
(1) The Mini Series range of enginesare normally fitted with a singlebelt to drive the 40 amp batterycharging alternator and the freshwater circulating pump.
(2) The belt tension is adjusted byswinging the alternator outboardas it pivots on its power supportbolt.
(3) With the engine stopped, loosenthe support bolts and the linkadjusting bolt.
(4) Push alternator outboard totension and tighten link bolt.
Check that the depression of thebelt at position shown isapproximately 1/2” or 12 mmwhen pushed down firmly bythumb. Tighten support bolts.
(5) Belt tension should be regularlychecked especially during the first20 hours of running in a newbelt, as stretching occurs.
Support bolt
Link adjust bolt
The same method, as outlined aboveapplies, but final tensioning must beby hand only. Over tensioning willcause premature failure ofcomponents
BELT TENSION
40 AMP ALTERNATOR
65 AMP ALTERNATOR (OPTION)
MAINTENANCE - ELECTRICAL
14
WARNING
Under NO circumstances should thebattery be disconnected or switchedoff when the engine is running. Thiswill seriously damage the alternator
PANELS AND WIRING
See installation notes, page 32.
GENERAL MAINTENANCE
(1) The panel must be protectedfrom rain and sea water, seeinstallation. Sea water enteringthe key switch will eventuallycause corrosion and could resultin the starter motor beingpermanently energised andburning out. Spray key switchevery month with WD 40 orequivalent.
(2) Check batteries for acid level and
top up if required. For lowmaintenance and ‘gel’ batteriessee manufacturers instructions.
(3) Loose spade terminalconnections are the mostcommon cause for electricalfaults - check on a regular bases(see maintenance instructions).
WINTERISING AND LAYING UP
HEAT EXCHANGER COOLEDENGINES LEFT AFLOAT ANDASHORE
(a) The engine oil and oil filtershould be changed at the end ofthe season rather than in thespring. See section 2.
(b) The closed circuit system shouldcontain a 50/50 solution of anti-freeze (this also applies to warmand tropical climates). Antifreezeshould be Ethylene Glycl basedconforming to BS6580:1992.
(c) For cold climates where the airor water temperatures can fallbelow 3°C, the sea water circuitmust be protected in addition tothe fresh water system. This isbest achieved as follows:
(i) Close the inlet seacock to theengine (engine stopped).
(ii) Disconnect the sea waterinlet pipe and dip it into a smallbucket containing 50/50 anti-freeze solution.
(iii) Start the engine (out of gear)and run for 5 to 10 seconds untilthe anti-freeze is used up andcan be seen coming out of theexhaust outlet.
(iv) Shut engine off andreconnect the inlet pipe to theseacock.
The sea water or raw watercircuit is now protected by anti-freeze.
(d) Ensure instrument panel is wellprotected and give the key switcha spray of WD 40 or equivalent.
(e) With the engine stopped,disconnect the battery (alwaysdisconnect the negative cable firstand re-connect the negativecable last) and take it ashore fortrickle charging and top up asnecessary. If AC power isavailable then this can be doneon the boat.
(f) Fuel tanks should be kept fullduring the lay up period toeliminate water condensation inthe tank. Water entering the fuelinjection system can causeconsiderable damage.
LAYING UP ASHORE
LAYING UP CANAL BOATS WITH KEEL COOLING
Follow items a, b, d, e and f. Item(c) does not apply. Special caremust be taken to ensure that thewhole cooling system has a 30%anti-freeze solution and this includesthe calorifier circuit.
If the system has been topped up orrefilled then run the engine for 10 to15 minutes on load (if possible) toget the solution circulated throughoutthe cooler and calorifier.
(a) Change the engine oil before theboat is taken out of the water.
Warm engine oil is much easierto pump than cold!
(b) to (f) should be followed asabove.
15
TROUBLE SHOOTINGBeta diesels are very reliable if installed and serviced correctly, but problems can occur and the following list gives themost common ones and their solution.
PROBLEM ENGINE DOES NOT START BUT STARTER MOTOR TURNS OVER OK
Possible Cause
No fuel:
Air in fuel system:
Water in fuel:
Blocked fuel pipe:
Fuel filter clogged:
Fuel lift pump blocked:
Blocked injector:
Fuel return not fed back to the tank:
Heater plugs not working:
Stop solenoid stuck in off position.
Solution
Turn fuel cock on and fill tank.
Vent air (see initial start-up)
Change fuel filter and bleed system.
Clean out and bleed system.
Change filter and bleed system.
Remove and replace.
Remove and clean.
Re-route fuel return pipe.
Check wiring to the plugs, and replace plugs if they are burnt out.
Check solenoid is free to return to run position.
PROBLEM: STARTER MOTOR WILL NOT TURN OR TURNS OVER VERY SLOWLY
Possible Cause
Battery discharged:
Starter motor flooded with sea water:
Wiring disconnected or loose:
Water in cylinders:
Engine harness fuse blown:
Solution
Charge battery or replace. Check alternator belt tension.
Remove and clean or replace.
Check circuit for loose connections.
Incorrect installation. This is serious - check engine oil for signs of water(creamy-coloured oil). Ring your dealer.
Replace fuse (located by starter motor or above flywheel housing) and check forwiring faults
FUSE
Note: For convenience, some engines are supplied with a sparefuse and holder attached onto the main engine fuse holder.
PROBLEM: WHITE OR BLUE EXHAUST GAS
PROBLEM: BLACK EXHAUST GAS
Solution
Inspect and replace
Check that the engine will reach full rpm in neutral; if it does get the propeller checked / re-pitched if necessary.
Inspect and clean if required
Possible Cause
Blocked air filter element
Over pitched propeller - engine willnot reach its full rpm:
Accumulated debris on hull
16
Possible Cause
Engine oil level too high:
Blocked injector:
Piston ring and bore worn, giving alow compression:
Check that the breather pipe is clearand not obstructed:
Solution
Reduce the level.
Service injectors.
Get compression checked by your dealer or Kubota service agent. He willadvise action to be taken.
Remove and clean out.
PROBLEM: ERRATIC RUNNING
Possible Cause
Air in fuel supply:
Fuel lift pump faulty:
Clogged fuel filter:
Fuel return not fed back to the fueltank, or blocked pipe:
Air filter blocked:
Worn or blocked injector:
Engine rpm in gear is too low, thismust be 850 min:
Faulty stop solenoid:
Broken fuel injection pump spring:
Solution
Check supply system for leaks and fix.
Replace.
Replace.
Re-route pipe or clean.
Replace.
Service injectors.
Increase engine tick over speed.
Disconnect wiring to solenoid. If running improves check for a wiring fault.
Replace.
PROBLEM: LOW POWER OUTPUT
Possible Cause
Propeller is too big:
Check gearbox reduction ratio relativeto propeller size:
Solution
Change or depitch.
Change.
17
PROBLEM: LOW POWER OUTPUT
Possible Cause
Blocked fuel filter:
Blocked air filter:
Air in fuel system:
Governor spring incorrectly mounted:
Single lever control not operatingcorrectly:
The electrical load is too large on startup.
Solution
Replace.
Replace.
Check system.
Dealer to adjust.
Disconnect speed control cable and move the lever by hand. Adjust cable.
Disconnect or reduce the load.
PROBLEM: HIGH OIL CONSUMPTION
Oil leaks:
Piston rings worn:
Valve stem and guide worn:
Piston rings gap facing the samedirection:
Check for leaks.
Overhaul required.
Overhaul required.
Shift ring gap position.
Possible Cause Solution
Core plug pushed out due to frozenblock:
Water pump seal damaged
Service Agent to check and replace.
Service Agent to check and replace.
Possible Cause Solution
PROBLEM: WATER IN LUBRICATING OIL - (Heat exchanger cooled)
Oil goes “milky” due to sea waterentering exhaust manifold and theninto the sump:
Check installation - has anti-siphon valve been fitted? Change engine oil and runengine for 10 minutes each time to eliminate any water. Get fuel injection pumpand compression checked by Service Agent.
Possible Cause Solution
PROBLEM: WATER IN LUBRICATING OIL - (Keel cooled)
Oil goes “milky” due to water enteringexhaust manifold and then into thesump:
Check installation – has dry exhaust system been fitted correctly, ensuring rainwater cannot enter the exhaust port and run back? (See DRY EXHAUST SYSTEM)Change engine oil and run engine for 10 minutes each time to eliminate anywater. Get fuel injection pump checked by Service Agent.
Possible Cause Solution
PROBLEM: WATER IN LUBRICATING OIL - (General)
18
PROBLEM: LOW OIL PRESSURE WARNING LIGHT comes on when engine speed reduced to tick over:
Faulty switch sender:
Engine running too hot:
Oil relief valve stuck partially openwith dirt:
Blocked oil filter:
Wiring fault:
Insufficient oil:
Replace.
Check cooling water flow (see section 2 Cooling).
Remove and clean.
Change.
Check circuit.
Top up and check for leaks.
Possible Cause Solution
PROBLEM: ENGINE OVERHEATS
Check coolant level:
Insufficient sea water flow:
Damaged or worn pump impeller:
Blocked tube stack in heatexchanger:
Zinc anode flakes blocking tube stack:
Pressure cap loose:
Switch sender faulty:
Inlet sea cock is too small:
High exhaust back pressure:
Air locks in cooling pipe work to keelcooler:
Keel cooler of insufficient size:
Possible Cause Solution
No W connection to alternator.
Wiring fault:
Check power output from ‘W’ connection. Should be about 9V AC.
Check circuit.
Possible Cause Solution
PROBLEM: PANEL REV COUNTER NOT WORKING (WHEN FITTED
Top up.
Clear blocked intake or filter.
Replace.
Remove tube stack and clean - replace ‘O’ rings.
Remove and clean tube stack as above.
Replace.
Replace.
Replace (see heat exchanger cooled seawater inlet system in section 3).
Must not exceed 3.1” of Hg.
Vent the system and top up coolant.
Contact boat builder.
19
The most common cause ofoverheating is insufficient seawaterflow due to a blocked intake (weedor a plastic bag!). If this happensthen clear the blockage. If theproblem is not cured then check thesystem for sea water flow whichshould be 6.5 litres / minuteminimum at 1,000 rpm as follows:
(a) With the boat tied up and out ofgear run the engine up to 1000 rpm.*Hold a plastic bucket over the
exhaust outlet for 10 seconds andmeasure the amount of watercollected. Multiply this value by 6 togive the flow in litres/min. Repeattwice and take an average. If the flowrate is noticably less than the 6.5litre per minute minimum, then:
(b) Check impeller in sea waterpump - if worn replace.
(c) If impeller has a vane missingthen this will be lodged either in the
pipe to the heat exchanger or in theend of the exchanger. This must beremoved.
(d) Check flow again as in (a).
*Note: This operation must only bedone in safe conditions, in port andwith two assistants.
Working from a rubber dinghy isbest. The person holding the bucketshould take precautions againstbreathing in the exhaust gasses.
PROBLEM: KNOCKING NOISE
Propshaft touching gearbox outputcoupling through split boss or Type16 coupling:
Flexible mount stud touching enginebed:
Drive plate broken:
Engine touching engine bed:
Adjust, giving correct clearance (10mm) between gearbox and propeller shaft.
Adjust stud to clear.
Replace / repair.
Re-align engine / modify bed.
Possible Cause Solution
PROBLEM: BATTERY QUICKLY DISCHARGES
High load and insufficient running:
Low electrolyte level:
Fan belt slipping - black dust inengine compartment: Enginecompartment temperature too high.
Alternator defective:
Battery defective:
Poor wiring connection:
Reduce load or increase charging time. Large domestic battery banks subjectto high electrical loads will take a considerable time to recharge from a singlealternator.
Top up.
Adjust tension / replace belt with a high temperature and/or improve enginebox ventilation.
Check with Agent.
Replace.
Check wiring system.
Possible Cause Solution
GENERAL -HEAT EXCHANGE ONLY:
20
PROBLEM: MORSE CONTROL CABLE WILL NOT FIT
Fitting incorrectly Cables are being fitted the wrong way around, switch over and fit the opposite way.
Possible Cause Solution
PROBLEM: VIBRATION
Poor alignment to shaft:
Flexible mounts not adjustedcorrectly to take even weight:
Flexible mount rubber perished:
Loose securing nut on flexiblemount:
Insufficient clearance between thepropeller tip and the bottom of theboat:
Loose zinc anode on the shaft:
Worn cutless bearing or shaft:
Weak engine support/bearers:
The alignment must be accurate even if a flexible coupling is used (see section3 ALIGNMENT).
Check relative compression of each mount.
Replace. (Diesel or oil will eventually perish most rubbers.)
Check alignment and then tighten the nuts.
There must be at least 10% tip clearance between propeller and bottom of theboat (ie 10% of the propeller diameter as clearance). Refer to boatbuilder.
Tighten or replace.
Replace.
Check for cracked or broken feet.
Possible Cause Solution
PROBLEM: TRANSMISSION NOISE
Check gearbox oil level:
“Singing” propeller:
Drive plate rattle at tickover:
Worn drive plate:
Propellor shaft hitting the gearboxhalf coupling
Top up.
Check with supplier.
Check engine rpm (must be 850 rpm minimum in gear).
Change.
Move shaft back to give at least 5mm clearance (type 12/16 couplings only)
Possible Cause Solution
The following chart is compiled to aiddiagnosis of electrical faults, based onthe Beta 10-90hp range of engines. Ifyour engine was built before July2005, contact Beta Marine for therelevant electrical trouble shootingguide.
Standard sea specification engines(heat exchanger cooled) are suppliedwith a single alternator, mounted portside, supplying power to starter batteryand control panel.
Standard canal specification engines(keel cooled) are supplied with twinalternators:
• 1st alternator, mounted port side,supplying power to starter batteryand control panel
• 2nd alternator, the standardmounting position for this is abovethe engine on the starboard side(or below 1st alternator on 75 &90hp), supplying power to thedomestic battery system.
Both of these alternators workindependently, if the domestic batterysystem is disconnected, the enginewill still run correctly but:
• Domestic charge warning lampwill not function
• Warning buzzer will remain on atall times
Standard control panels are suppliedwith four or five lamps:
Four lamp panels:A, ABV, ABVW, B these panels utilisebulbs inside sealed lamp holders
Five lamp panels:AB and C, these panels also utilisebulbs inside sealed lamp holders,having an additional lamp fordomestic battery charge
With keyswitch* in run position &engine off:
• Red lamp for no starter batterycharge should function
• Red lamp for no domestic batterycharge should function (Note: thiswill only function if a secondalternator is fitted to the engineand connected to a chargedbattery)
• Red lamp for high enginetemperature should not function(when engine is cold / cool /warm). This lamp will only everfunction if the engine is overtemperature.
• Red lamp for low oil pressureshould function
• Green lamp for panel power onshould function
• Buzzer should sound
* For operation of engines controlledwith keyless panels refer to ‘correctoperation of keyless panels’ later inthis section
When the engine is started, all the redwarning lamps should switch offleaving just the green power onindication lamp illuminated. The oilpressure lamp may take a fewseconds to switch off and the chargefail lamp may remain on until enginerpm is increased to approximately1,000rpm if the engine was started attickover).
Before investigating any specificelectrical problem, always check:
• Connection between panelharness and panel loom. It mustbe clean, dry and secured with acable tie.
• Check the start battery isconnected to the correct terminalon the starter motor.
• Check the domestic battery isswitched on and connected to thecorrect terminals for the 2ndalternator.
• Battery connections, inspectingcondition of cables from battery toengine. If in doubt measure thevoltage at the engine.
• If alternator charge problem,measure battery voltage withengine off and again with enginerunning, if there is an increasealternator is functioning correctly, ifnot refer to check list.
Note: The two way plug on panelloom will only have a correspondingsocket to connect into from the engineif a 2nd alternator is fitted whichrequires this connection. Engines withonly one alternator do not utilise thisconnection.
21
ELECTRICAL FAULT FINDING & TROUBLE SHOOTING –ENGINES BUILT AFTER JULY 2005 ONLY
Typical start battery negative
Typical start battery positive
All Beta panels have the following warning lamps: (A, AB, ABV, ABVW, B and C Deluxe)
Starter battery charge warning lamp Red
• High engine temperature warning lamp Red
• Low engine oil pressure warning lamp Red
All panels also have:
• Panel power on (this is not a warning lamp) Green
In addition to above the domestic AB, C Deluxe panels also have a:
• Domestic battery charge warning lamp Red
22
PROBLEM POSSIBLE CAUSE & SOLUTION
No warning lamps or buzzer functioning, engine will not start or stop
• Battery isolation switch in off position –switch on• Starter battery discharged – charge• Engine fuse blown –check fuse (above starter motor or flywheel housing) & replace
if necessary. • Check for wiring faults.
Non function of warning lamp
THE WATER TEMPERATURE LAMPWILL NOT FUNCTION UNLESS ENGINEIS OVERHEATING OR THERE IS AWIRING FAULT
• Disconnect switch wire to non-functioning lamp: green/blue –water temperature,white/brown –oil pressure, brown/yellow –alternator charge. Reconnect wiretemporarily to another warning lamp that is functioning; if wire switches lamp onreplace faulty lamp.
• Disconnect positive feed to non-functioning lamp. Reconnect temporarily with wirefrom another warning lamp that is functioning, if wire switches lamp on rewire withnew connection.
• If none of the above, check continuity of connections from panel to engine.
Water temperature warning Lamp on whenengine is not over temperature
(Not B or C deluxe panel see table onfollowing page)
If engine is cold:
• Faulty wiring, check connection & continuity (small green / blue) from switch topanel lamp. Ensure this connection is not shorting to earth (ground).
• Faulty temperature switch –if lamp switches off on removal of connection to switchunit, replace.
If engine is warm:
• Switch wire connected to large sender terminal of switch / sender unit. Removeand refit to smaller (switch) terminal
Buzzer not functioning
THE BUZZER WILL NOT SOUND FORGREEN POWER ON LAMP
• - If lamp is functioning but buzzer not sounding, check connection & continuity fromilluminated warning lamp (red not green) to buzzer board.
• - Faulty warning panel buzzer board –replace.
Starter battery charge lamp not functioning
• If tacho not functioning:• Alternator not connected properly, check continuity of small brown wire from rear of
alternator to ‘AC’ position on keyswitch.• alternator connected properly, faulty alternator –replace• If tacho functioning correctly:• Check continuity of small brown/yellow wire from rear of alternator to no charge
warning lamp on rear of panel.• If alternator connected properly, faulty panel warning lamp –replace
Tacho not functioning
• -Check connections on rear of tacho, especially black/blue wire, terminal ‘4’• -Check connection of black/blue wire on rear of 1st alternator (W connection,
usually a bullet on flying lead, or lowest connection on alternators with 3 pincoupler)
• -Check continuity of black/blue wire from alternator to tacho• -Measure voltage from alternator W connection to earth (ground), should be
approx. 7.5 – 9.0 volts AC
Domestic charge lamp not functioning,buzzer remains on with engine running
• Domestic battery not connected• Domestic battery not connected correctly:B+ to domestic isolation block on starboard rail (port on 75 & 95hp)B- to engine earth (ground)• Domestic battery flat• Panel relay faulty / incorrectly wired:Check voltage at relay terminal 86, white wire is positive feed for warning lamp fromAC position of keyswitch.
Domestic charge lamp not functioning,buzzer switching off with engine runningTHIS LAMP WILL NOT FUNCTION IF A SINGLEALTERNATOR IS FITTED TO THE ENGINE
• No second alternator fitted to engine, domestic lamp not used• D+ (charge indication) lamp connection at rear of alternator not connected• Two way plug & socket disconnected between engine harness & panel loom
ELECTRICAL FAULT FINDING –LED PANELS
23
PROBLEM POSSIBLE CAUSE & SOLUTION
Oil pressure warning lamp not functioning, oilpressure gauge showing maximum deflection.Engine off and keyswitch in run position
• Faulty wiring –check wire connection & continuity (small white/brown) from senderto panel lamp. Ensure this connection is not shorting to earth (ground).
Oil pressure gauge showing no movement -even when engine is started. Warning lampfunctioning correctly
• Faulty wiring –check oil pressure sender wire (small white / brown) is connected.
Oil pressure showing no movement, Warninglamp not functioning correctly
• Check connection to oil pressure gauge, if plug is not connected to socket on rear ofgauge reconnect.
• If all connections are correctly made, possible faulty sender unit –check resistance toearth (ground) approx. 50W. Replace if no reading or short-circuited.
• If adjusted correctly & buzzer still sounding, possible faulty switch gauge unit – replace.
Oil pressure showing normal operatingpressure (0.75–5 bar). Buzzer sounding &lamp illuminated.
Engine warm:
• Incorrectly calibrated switching point for warning lamp, adjust on rear of gauge to0.5 bar (minimum adjustment on gauge).
• If adjusted correctly & buzzer still sounding, faulty switch gauge unit – replace.
Water temperature gauge showing 120°C / 250°F
THIS ALSO APPLIES TO THE B PANELWITH MURPHY GAUGE
Engine cold / cool:
• Faulty wiring, check water temperature sender wire is not shorting to earth• Faulty sender unit, –check resistance to earth, approx. 3.5kΩ (cold) – 0.5kΩ
(warm). Replace if notably less.
Water temperature gauge showing normaloperating temperature (85°C). Buzzersounding & lamp illuminated.
THIS ALSO APPLIES TO THE B PANELWITH MURPHY GAUGE
Engine warm:
• Incorrectly calibrated switching point for warning lamp, adjust on rear of gauge to100°C.
• If adjusted correctly & buzzer still sounding, faulty switch gauge unit – replace.
Water temperature gauge showing nomovement, LED not illuminated, enginewarm.
• Check connection to sender, if disconnected gauge will not function.• Check connection to temperature gauge, if plug is not connected to socket on rear
of gauge reconnect. • If all connections are correctly made, faulty sender unit –check resistance to earth,
approx. 3.5kΩ (cold) – 0.5kΩ (warm). Replace if no reading.
ELECTRICAL FAULT FINDING – C DELUXE & WATER TEMPERATURE FUNCTION ON B PANELSIn addition to the fault finding detailed on the previous table, the following is specific for the C Deluxe type deluxe panel (Alsoapplicable for the B panel with Murphy water temperature gauge)
24
ELECTRICAL FAULT FINDING –NON BETA PANELS
Engines can be supplied wired up tosuit VDO switch senders, usuallyfitted to a non-Beta control panel.
If so refer to our wiring diagram 200-60971/01 (also part number forreplacement harness)
• Loom is configured differently inthe 11-way plug toaccommodate the extra wiring.
• Small brown wire (battery sensedalternator feed) fitted with bulletconnection beside harness plug.
• Oil pressure & water temperatureswitch / senders fitted to engine,requiring individual connectionsfor driving gauges & warninglamps.
Note: Water temperature switch / sender (Part number 200-01133)
• large spade is sender connection (green / blue)
• small spade is switch connection (blue / yellow)
Oil pressure switch / sender (Part number 200-62680)
• G Gauge wire (white / brown)
• M Earth (black)
• WK Warning lamp (green / yellow)
ELECTRICAL FAULT FINDING –EXTENSION HARNESSESSome installations require one of thepanel extensions 11 way connectorsto be removed to allow the cable tobe passed through bulkheads etc. Ifany panel problems are experiencedafter this may have been carried out,visually check all 11 wayconnections on engine harness to
panel extension (and panel extensionto panel on C deluxe) to ensure wirecolours to each terminal match up tothe correct colour in its correspondingterminal. Extra attention must begiven to black (ground) andblack/blue (tacho), also brown(switched positive to alternator) and
brown/yellow (charge fail) as theseconnections are harder to distinguishbetween in poorly lit areas. Whilstdoing this check integrity of eachconnection to ensure terminals havenot become damaged. Oncechecked, re-fit cable tie around eachconnection to keep them secure.
ELECTRICAL – CORRECT OPERATION OF KEYLESS PANELS
These panels control the engine withthree water resistant push buttonsinstead of a keyswitch, which are lessprone to damage and corrosion fromsea water spray than a keyswitch.To operate the engine:1. Press and hold ‘HEAT’ button for
ten seconds maximum• Red lamp for no starter battery
charge should function• Red lamp for high engine
temperature should not function(when engine is cold / cool /warm). This lamp will only everfunction if the engine is overtemperature.
• Red lamp for low oil pressureshould function
• Green lamp for panel power onshould function
• Buzzer should sound2. Press ‘START’ button and hold in
position until engine fires (seeinitial start-up section formaximum time starter can beoperated). Release button (whenengine has started)
• All red warning lamps shouldextinguish and buzzer should stopsounding. The oil pressure lampmay take a few seconds to switchoff and the charge fail lamp mayremain on until engine rpm isincreased to approximately1,000rpm if the engine wasstarted at tickover.
• Green lamp for panel power onshould still function
3. To stop the engine press the‘STOP’ push button, hold in untilengine stops. This button alsoswitches the power off to thegauges, engine and power onlamp.
4. To re-start the engine, simplyrepeat steps from ‘1’ above, thereis not need to switch batteryisolators off whilst remaining onboard.
5. If leaving the boat, isolate startbattery from engine and panel, toprevent accidental start up ofengine.
25
BETA PART NUMBERS FOR REPLACEMENT ITEMS:
Description Part number
40 amp blade fuse (all panels) 200-00959
Alarm board –all panels from June 05 200-04655
Oil pressure switch 1/8”BSP (not C panels) 600-62670
Oil pressure sender (C panels only) 200-94350
Oil pressure switch gauge (C panels only) 200-96190
Temperature switch with single terminal (on some Beta 16 & Beta 25) 600-62820
Temperature switch / sender 1/8”BSP (not B or C panels) 200-01133
Temperature sender (B & C panels only) 200-94360
Water temperature switch gauge (B & C panels only) 200-96200
Voltmeter (C panels only) 200-96210
28Ra relay 12V 40A (fitted to rear of domestic panels) 200-87020
Keyswitch, silver bezel 600-00057
Panel stop button (all panels) –Also heat and start on ABVW 200-00072
Tacho, 0-4000rpm with digital hour counter (all panels but A) 200-02373
Standard engine harness Mini Series 200-98380/01
Standard engine harness S5 Series 200-60973/05
Standard engine harness S3 series 200-05267
Iskra 65 amp sub loom 200-01196
1m panel extension loom 200-04588/01
2m panel extension loom 200-04588/02
3m panel extension loom 200-04588/03
4m panel extension loom 200-04588/04
Domestic charge engine sub loom (top mounted alternators) 200-01197
Green power on indicator lamp & retaining clip 200-04656
Red warning indicator lamp & retaining clip 200-04657
Note: the above part numbers aresuitable for earth return installationsonly (where battery negative cable isconnected directly to engine ground).For insulated earth (where batterynegative cable is isolated from engineground) different harnesses,
alternators, switches for oil pressureand engine temperature will berequired. If your application is wiredas insulated earth return and theengine will not operate correctly,always check starter battery negativeis connected to the correct terminal on
the isolating solenoid. It should beconnected to the terminal which isalso used for all the small black wires,NOT the terminal with the singleblack wire connected directly toengine ground.
26
Spanner torque settingsTightening Torques for general use bolts and nuts
ITEM Size x Pitch kgf .m ft .lbs N.m
M6 (7T) : 6mm (0.24in) – 1.0~1.15 7.2~8.3 9.8~11.3
M8 (7T) : 8mm (0.31) – 2.4~2.8 17.4~20.3 23.5~27.5
M10 (7T) : 10mm (0.39in) _ 5.0~5.7 36.2~41.2 49.0~55.9
M12 (7T) : 12mm (0.47in) _ 7.9~9.2 57.1~66.5 77.5~90.5
Tightening Torques for special use bolts and nuts
Head Bolts M8 x 1.25 3.8 ~4.3 27.5~31.1 37.3~42.2
Bolts, Connecting Bolts M7 x 0.75 2.7~3.1 19.5~22.4 26.5~30.4
Bolts, Flywheel M10 x 1.25 5.5~6.0 39.8~43.4 53.9~58.8
Bolts 1, Bearing Case M6 x 1.0 1.3~1.6 9.4~11.6 12.7~15.7
Bolts 2, Bearing Case M7 x 1.0 2.7~3.1 19.5~22.4 26.5~30.4
Nozzle Holder Assembly M20 x 1.5 5.0~7.0 36.2~50.6 49.0~68.6
Caps Nuts, Head Cover M6 x 1.0 0.4~0.6 2.9~4.3 3.9~5.9
Glow Plugs M8~1.0 0.8~1.5 5.8~10.8 7.8~14.7
Oil Switch PT 1/8 1.5~2.0 10.8~14.5 14.7~19.6
Nuts, Rocker Arm Bracket M6 x 1.0 1.0~1.15 7.2~8.3 9.8~11.3
Bolts, Idle Gear Shaft M6 x 1.0 1.0~1.15 7.2~8.3 9.8~11.3
• All engines shall be placed withinan enclosure separated from livingquarters and installed so as tominimise the risk of fires or spreadof fires as well as hazards fromtoxic fumes, heat, noise orvibrations in the living quarters.
• Unless the engine is protected by acover or its own enclosure, exposedmoving or hot parts of the enginethat could cause personal injuryshall be effectively shielded.
• Engine parts and accessories thatrequire frequent inspection and / orservicing must be readilyaccessible.
• The insulating materials insideengine spaces shall be notcombustible.
27
Section 3INSTALLATION RECOMMENDATIONSThe installation details contained herewith are basic guidelines to assist installation, due to great diversity of marine craft it isimpossible to give definitive instructions. Therefore Beta Marine can accept no responsibility for any damage or injury incurredduring the installation of a Beta Marine Engine whilst following these guidelines.
To ensure vibration free operation, theengine must be installed on substantialbeds, extending as far forward and aftas possible and well braced to form anintegral part of the hull.
The engine must be installed as low aspossible on the flexible mount pillarstud. This will limit vibration andextend the life of the flexible mount. Ifnecessary, fit spacer blocks below themounts.
A flexible coupling should be fitted.Flexible couplings do not accommodatebad alignment. The mating faces of thegearbox and tailshaft must be checkedfor alignment, they must be paralleland concentric to within 0.005”(0.127mm).
ALIGNMENT Alignment must be checked forparallel (A) and concentric (B)misalignment using a set of feelergauges. To obtain accurate alignmentthe flexible mountings must beadjusted until alignment is attained,and the mountings must be locked inposition. Once mounts are tightened,alignment must be re-checked.Coupling can now be fitted inaccordance with instructions suppliedwith coupling.
WARNING1. Do not set the engine feet high up
the flexible mount pillar stud. Thiswill cause excessive enginemovement and vibration. Packunder the flexible mount with steelshims securely bolted into theengine bearer.
2. The pillar stud on the flexiblemount is secured into position bythe lower locknut, do not forget totighten this. Also ensure that thestud is not screwed too far throughthe mounting body so that it cantouch the bearer. This will causevibration and knocking noiseswhich are very hard to find!!
Flexible Mount
ENGINE MOUNTING
A
B
C
28
TYPICAL YACHT INSTALLATION
Anti syphon valveor T piece fitted here
300mmminimum
WaterlockSilencer
X
aNormal seawater level
Maximum sea water level when heeled(on the centre line of the boat)
Exhausts Beta 10 BZ482 / Beta 16 BD722 / Beta 25
Standard 50mm 50mm 50mm
Option 15/8” is available in SS 15/8” 15/8” 15/8”
High rise water injection bend SS 50mm 50mm 50mm
Cross over injection bend SS 50mm 50mm 50mmto suit Volvo replacement engines.
EXHAUSTS
Allow at least10% of propellerdiameter for tipclearance to hull
If a rope cutter is fitted, allow approximately 1/2”Û for movement of engine, seemanufacturer’s literature
WARNING:
(1) One of the most commonproblems with engine installation iswater entering the exhaust manifoldfrom the exhaust system bysyphoning. This can occur when thepoint of water injection (X) on theengine is close to or below the waterline. Water entering the pistons cancause bent con rods, emulsified
engine oil and a wrecked fuel pump!Its best avoided!
(2) The diagram shows a typicalinstallation. It is essential that thesmall black rubber hose connectingthe heat exchanger with the injectionbend is removed and replaced by ahose marked ‘a’. This must be ofsufficient length to
supply either a T piece or an antisyphon valve sited at least 300mm(12 inches) above the water line andon the centre line of the boat. Thepipe then returns to the injection bendand the sea water is pumped downthe exhaust pipe.
(3) The exhaust back pressure shouldnot exceed 3.1 inches of Hg.
(a) A correctly installed engine asdescribed in this handbook will meetthe exhaust emission requirements ofDirective 2003/44/EC amending theRecreational Craft Directive 94/25/EC.
(b) For compliance with exhaustemissions requirements, engines musthave correctly installed exhaustsystems. To ensure exhaust emissionsare kept within permissible limits it ismost important to reduce exhaustback pressure to a minimum, whilstensuring exhaust is adequatelymuffled. Back pressure increases asexhaust length increases and from
bends in the exhaust system. Theexhaust back pressure, measured withthe exhaust system connected and theengine running at full speed, must notexceed 80mmHg (3.1 inches Hg / 42inches WG). The correct measuringpoint is at the
position where the exhaust connectsto the exhaust manifold. That is beforethe water injection elbow or dryexhaust bellows.
Wet Exhaust hose should be matchedto the injection bend sizes detailedabove.
1
9
11
7
5
102
3
8 4
126
FUEL SUPPLY & LEAK OFF - A typical system is shown below
(1) Fuel tank
(2) Injection pump
(3) Injection nozzle
(4) Injection pipe
(5) Mechanical fuel feedpump with priming lever
(6) Fuel filter
(7) Fuel water separator
(8) Overflow/leak off
(9) Drain plug
(10) Air vent
(11) Stop cock
(12) Fuel pipe loop
29
Ensure exhaust raises then falls to outlet
The exhaust system installed in acanal boat or work boat with a dryexhaust should be 11/2” minimum ID.The engine is fitted with a 11/2” BSP maleconnector when a dry exhaust system isspecified. A flexible exhaust bellows anddry exhaust silencer should be used. It isup to the installer to work out his ownpipe run but care should be taken asfollows:
(1) Ensure that rain water cannotenter the exhaust port and runback down the system, floodingthe silencer and eventually theengine.
(2) The system should be lagged ifthere is any danger of the crewgetting near it.
(3) A dry exhaust system will give offconsiderable heat and suitableventilation must be provided.
(4) The exhaust back pressure shouldnot exceed 3.1 inches of Hg.
DRY EXHAUST SYSTEM
3 7
30
SEAWATER INLET SYSTEM (HEAT EXCHANGER COOLED ENGINES)
Notes:
1. The mechanical fuel lift pump isfitted to all engines as standard,but if a suction head of 0.25m isrequired then an electric fuel liftpump must be fitted (ask yourdealer or Beta Marine).
2. It is very important that theexcess fuel from the injectors isfed back to the fuel tank and notback to any point on the supply
line. This will help prevent airgetting into the system.
4. Any fuel leaks in the system arelikely to cause poor starting anderratic running and must becorrected immediately.
5. A fuel/water separator must beinstalled.
6. The fuel return (leak off) pipemust loop down to be level with
the bottom of the tank before itenters the top of the tank - see12. This prevents fuel ‘draindown’.
7. Fuel lines and hoses must besecured and separated orprotected from any source ofsignificant heat. The filling,storage, venting and fuel supplyarrangements and installationsmust be designed and installed soas to minimise the risk of fire andexplosion. Flexible fuel hosesconnecting the engine to fuel tanksupply and return lines must meetthe requirements set in standardISO 7840:1995/A1:2000 and asrequired by your surveyor /authority.
3. Fuel pipe sizes are: Supply (mm) Leak off (mm)
Beta 10 8 8
BZ482 / Beta 16 8 8
BD722 / Beta 25 8 8
Your engine is fitted with a geardriven sea water pump which sucksin seawater or raw water to cool theclosed circuit system via the heatexchanger.
1. It is very important that theseawater inlet should have astrainer system either built intothe sea cock or a high levelsystem with visual inspectionglass, as shown, mounted justabove the water line.
Water Level
2. The inlet sea cock and pipe workto the sea water pump should be22mm ID or 3/4” minimum.
3. Good access to the inlet seacockis essential so that plastic bags orsea weed trapped in the intakecan be poked out!
4. All pipe work should haveapproved marine grade stainlesssteel hose clips. Any looseclamps or bad connections can
cause flooding and sinking of thevessel.
5. If water is required for stern tubelubrication then this should betaken from a ‘T’ piece in the pipegoing from the heat exchangeroutlet to the water injection bend.
6. Scoop type water pickups shouldnever be used, as water will beforced through the pump andinto the exhaust system whilst
the vessel is in motion. This isvery dangerous as the exhaustwill eventually fill and raw waterwill back up into the enginethrough the exhaust valve.Catastrophic failure will result assoon as the engine is restarted.
Note: The maximum lift of the seawater pump is 2m
31
Also check to see if the pipegoing to the calorifier is gettingwarm after 15 minutes.Top upthe water level as required andrun for another 10 minutes thenrepeat.
4. If the water level is steady but nowarm water is getting to the
calorifier then very carefully openthe calorifier bleed valve (seemanufacturers instructions) or ifnone is provided then verycarefully loosen the jubilee clipsecuring the supply pipe to thecalorifier . Air should escape.Refasten securely when nofurther bubbles are seen.
CAUTION
Do not do this when the engine ishot as scalding hot water may beforced out of the pipe under pressure.
KEEL COOLED
1. The supply pipe to the keelcooler should be 22mm boreand the return 22mm bore.
2. The tank size should have asurface area (x) exposed to thesea water or canal water of (0.25x the bhp of the engine) = sq ftof cooling area required. Forcanal boats this should beadequately baffled and a ventprovided to expel any air. Thesupply (hot water) goes in at thetop of the tank and the returncomes out of the bottom. Alsorefer to cooling tank notes onpage 10.
(1)
Baffle continuously welded toouter skin and close fitting oninner skin.
(2) The tank should be thin insection to allow good mixing of
the water over the cool outer surface.
(3) Air bleed valves should be fittedboth ends.
IDEAL KEEL COOLING TANK
CALORIFIER SYSTEMAll Beta engines can be fitted withthe engine tappings to allow the hotwater from the closed freshwater/antifreeze system to circulatethrough a calorifier tank which inturn heats up domestic water.
Calorifier tappings on this range ofengine are shown below.
1. The big problem with a calorifieris to remove all the air from thesystem. If this is not achievedthen they don’t work!
2. Try and keep the supply andreturn pipes a and b eitherhorizontal or sloping down in acontinuous fall. This avoids airpockets being created.
3. Extra care must be taken whenfirst filling the calorifier circuitsystem with 50% antifreeze towater solution as the engine mayappear to be full but it soondisappears into the calorifier pipework. Run the engine off load for10 minutes then check the levelas described in ‘Filling The FreshWater System’.
b
aa
b
Heat Exchanger Version Keel Cooled Version
Air bleed valves
APPENDICES –WIRING DIAGRAMS & GENERAL ARRANGEMENTS1. Keyswitch terminations Page 332. Standard harness 200-05444 Page 343. 65 amp harness 200-05495 Page 354. Diagram of A panel & cut-out 200-06516 Page 36 & 375. Diagram of AB panel & cut-out 200-06517 Page 38 & 396. Diagram of ABV panel & cut-out 200-06519 Page 40 & 417. Diagram of ABVW panel & cut-out 100-06333 Page 42 & 438. Diagram of C panel & cut-out 200-06520 Page 44 & 459. Diagram of C Deluxe panel & cut-out 200-06518 Page 46 & 4710. Blocking diode diagram –40A alt 300-62220 Page 4811. Split charge diagram –65A alt 300-62210 Page 4912. Starter booster relay 300-58520 Page 5013. GA of B10 H/E -TMC40 100-00030 Page 5114. GA of BZ482 H/E -TMC40 100-06019 Page 5215. GA of Beta 16 (BZ602) H/E -TMC40 100-06496 Page 5316. GA of BD722 H/E -TMC40 100-99610 Page 5417. GA of BD722 H/E -PRM80 100-01048 Page 5518. GA of BD722 K/C -PRM80 100-05749 Page 5619. GA of Beta 25 (BD902) H/E –TMC40 100-06495 Page 5720. GA of Beta 25 (BD902) H/E –PRM120 100-06509 Page 5821. GA of Beta 25 (BD902) H/E –TTMC35 100-06494 Page 5922. Declaration of Conformity for Recreational Craft Page 6023. Maintenance record and service items Page 64 & 65
NOTE: for dual battery charging on Beta 16 and Beta 25 models fitted with the optional 60 Amp alternator, a blocking diodearrangement be utilised, refer to 300-62220. This is a battery sensed machine, incompatible with our standard split chargerelay.
32
ELECTRICAL INSTALLATIONS
Beta has 4 panels: A -standard
AB or ABV or ABVW
B
C
The engine harness is common toall.
1. These panels must not beinstalled where sea water spraycan get at them. A suitable flapor cover must be fitted.
2. Panels must be fitted in alocation where the helmsmancan either see or hear the alarmsystem.
3. For standard wiring diagrams seefollowing pages.
4. Extension looms longer than 3m(10 feet): As an option, Beta can
provide various lengths ofextension looms for runs of over3m, but this kit includes a startrelay to overcome the voltagedrop. (See drawing 300-58520)
5. All electrical equipment must beprotected from sea water. Seawater or rust in the starter willinvalidate the warranty.Care must be taken whenpushing the two halves of theplug together to ensure thatindividual pins do not fall out. Toprevent corrosion and assist inassembly we recommend thatthe plug is packed withpetroleum jelly (Vaseline) andthen carefully pushed together.The plastic boots should coverboth halves and overlap. A cabletie is then put around to hold thetwo halves in position and helpprevent any ingression of water.
6. All cables must be adequatelyclipped and protected fromabrasion.
7. Electrical systems shall bedesigned and installed so as toensure proper operation of thecraft under normal conditions ofuse and shall be such as tominimise risk of fire and electricshock.
8. Attention shall be paid to theprovision of overload and short-circuit protection of all circuits,except engine starting circuits,supplied from batteries.
9. Ventilation shall be provided toprevent the accumulation ofgases, which might be emittedfrom batteries. Batteries shall befirmly secured and protected fromingress of water
33
Engine Starter capacity (kW)
Less than 700cc 0.8 to 1.0
700 to 1500cc 1.0 to 1.4
Engine (cc) Typical Battery Capacity Typical C.C.A. (A)(AH) at a 20hr Rate Cold Cranking Amperage
Beta 10/BZ482/Beta 16 35~ 40 350~ 405
BD722/Beta 25 65~ 75 450~ 540
KEYSWITCH TERMINATIONS
The standard panel keyswitch can beused to tap off a switched positiveignition feed to power additionalgauges. In this way these gauges willonly be live whilst the engine isrunning, the engine is starting or theheaters are being used.
For silver keyswitches, the terminal toachieve this ignition switched positiveis marked ‘AC’.
For black keyswitches, the terminal toachieve this ignition switched positiveis marked ‘15/54’.For panels without any keyswitch,gauges can be driven from the 1mm2
brown wire which teriminates at 11way connector terminal 4. This is alower power switched positive, anyadditional power required from thisconnection must be feed through arelay, as noted below.
Note: these keyswitch terminals arerated at 10 amps maximum, sincethey are already utilised for panel andalternator feeds Beta Marinerecommend any additionalrequirements from these terminalsmust be fed through a relay. Thisrelay should then be connected to it’sown fused positive supply directly fromthe engine battery.
Beta drawing 202-06421 illustratingthe wiring of a typical electric fuel liftpump with ignition switched relay canbe supplied upon request.
SUGGESTED MINIMUM ENGINE STARTER BATTERY SIZE:
TYPICAL STARTER MOTOR RATINGS:-
Starters used in Kubota engines have the following standard capacities
34
35
36
37
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
TH W
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
NTS
A4
2 of
2
200-
0630
515
/11/
2004
2A P
AN
EL
TW LT
MA
TL:
00
10.0
010
.00
150.
00
10.0
0
10.0
0
90.0
0
5.00
140.
00
5.00
80.0
0
50.3
2AD
D 30
mm
FOR
WIR
ES
20.12 36
.68
38
39
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
TH W
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
NTS
A4
2 of
2
200-
0630
415
/11/
2004
2AB
PA
NE
L
TW LT
MA
TL:
01
10.0
010
.00
195.
00
10.0
0
10.0
0 180.
00
50.3
2AD
D 30
mm
FOR
WIR
ES
22.6
2
36.6
8
5.00
185.
00
5.00
170.
00
O 5
.00
THRU
40
41
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
TH W
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
NTS
A4
2 of
2
200-
0632
0/01
23/1
1/20
04
AB
V P
AN
EL
TW LT
MA
TL:
00
140.
0
10.0
180.
0
10.0
10.0
O 5
.0 T
HRU
5.0
5.0
170.
0
130.
0
20.0
20.0
22.6
50.3
ALLO
W30
mm
FOR
WIR
ES36
.7
42
43
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
TH W
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
NTS
A4
2 of
2
200-
0633
101
/12/
2004
AB
VW
WA
TER
PR
OO
FP
AN
EL
TW LT
MA
TL:
AS U
SED
ON K
1474
4
00
180.
00
10.0
016
0.00
5.00
20.0
0
5.00
10.0
0
120.
0014
0.00
5.00
20.0
0
5.00
50.5
0AL
LOW
30m
m F
OR W
IRES
22.6
2
O 5
.00
THRU
44
45
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
TH W
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
NTS
A4
2 of
2
200-
0630
315
/11/
2004
2B P
AN
EL
TW LT
MA
TL:
00
210.
00
10.0
010
.00
10.0
0165.
00
5.00
200.
00
5.00
155.
00
50.3
2AL
LOW
30m
m F
OR W
IRES
22.6
236
.68
47
47
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
TH W
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
NTS
A4
2 of
2
200-
0630
615
/11/
2004
2CP
AN
EL
TW LT
MA
TL:
DE
LUXE
00
10.0
010
.00
298.
00
10.0
0166.
00
10.0
0
5.00
288.
00
5.00
156.
00
50.3
2AD
D 30
mm
FOR
WIR
ES
22.6
2
36.6
8
48
49
50
51
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
THW
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
A4
1 of
1
100-
0003
020
/12/
2005
BE
TA10
HE
AT
EXC
HA
NG
E
TW
TMC
40 G
EA
RB
OX
02
67.5
340
185185
159
244
582
185
18522
2
50O
137
294
F.W
FIL
LER
CAP
O IL
FILT
ER
SEA
WAT
ER P
UM
PIN
LET O
22m
m M
ALE
STU
B
LUBE
OIL
DIPS
TICK
FUEL
FIL
TER
TO C
ALO
RIFI
ER5/
8" B
SP B
ORE
HOSE
OIL
FIL
LER
CAP
FUEL
BLE
ED S
CREW
GEAR
BOX
OIL
FIL
LERGE
ARBO
XO
IL D
IPST
ICK
AIR
FILT
ER
FROM
CAL
ORIF
IER
5/8"
BSP
BO
RE H
OSE
SACR
IFIC
IAL
ANOD
E
FUEL
INTA
KE8m
m H
OSE
TAIL
FUEL
RET
URN
8mm
HOS
E TA
IL
GEAR
BOX
OUTP
UT O
82.5
O63
.5H8
4 HO
LES
O10
.5 T
HRU
FLEX
IBLE
MOU
NTDE
TAILS
100
120
63
65M
IN90
.0M
AX
182
WIT
H SH
ALLO
W S
UM
P
45Am
p12
VAL
TERN
ATOR
NEW
TIT
LE B
LOCK
15-0
1-04
LTTW
02UP
DATE
D TO
MAT
CH T
IER2
AND
FUE
L FI
LTER
SYS
TEM
20-1
2-05
TW
NTS
BATT
ERY
POSI
TIVE
BATT
ERY
NEGA
TIVE
3
12
63
212
222
SUM
P DR
AIN
PLU
G
52
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
THW
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
A4
1 of
1
100-
0601
920
/12/
2005
BZ4
82H
EA
TE
XCH
AN
GE
TW
TMC
40 G
EA
RB
OX
04
67.5
251±3340
185185
159
244
582
185
185
218
222
50O
137
294
F.W
FIL
LER
CAP
O IL
FILT
ER
SEA
WAT
ER P
UM
PIN
LET O
22m
m M
ALE
STU
B
LUBE
OIL
DIPS
TICK
FUEL
FIL
TER
TO C
ALO
RIFI
ER5/
8" B
SP B
ORE
HOSE
OIL
FIL
LER
CAP
FUEL
BLE
ED S
CREW
GEAR
BOX
OIL
FIL
LERGE
ARBO
XO
IL D
IPST
ICK
AIR
FILT
ERSU
MP
PUM
P
FROM
CAL
ORIF
IER
5/8"
BSP
BO
RE H
OSE
SACR
IFIC
IAL
ANOD
E
FUEL
INTA
KE8m
m H
OSE
TAIL
FUEL
RET
URN
8mm
HOS
E TA
IL
GEAR
BOX
OUTP
UT O
82.5
O63
.5H8
4 HO
LES
O10
.5 T
HRU
32
O82.5
8 M
10 X
50
BOLT
SEQ
UI-
SPAC
ED O
NAN
82.
5mm
PCD
FLEX
IBLE
COU
LPIN
G DE
TAILS
FLEX
IBLE
MOU
NTDE
TAILS
100
120
63
65M
IN90
.0M
AX
182
WIT
H SH
ALLO
W S
UM
P
SUM
P PI
CK U
P ON
SHAL
LOW
SU
MP
ONLY
45Am
p12
VAL
TERN
ATOR
NEW
TIT
LE B
LOCK
15-0
1-04
LTTW
02BA
TTER
Y CO
NNEC
TION
S AN
S W
ASTI
NG A
NODE
11-1
0-04
03FU
EL F
ILTER
, H/E
TAN
K AN
D AI
R FI
LTER
25-0
7-05
04CA
LORI
FIER
S AN
D TI
ER2
CLOS
ED B
REAT
HER
20/12
/05
LTTW
LTTW TW
NTS
BATT
ERY
POSI
TIVE
BATT
ERY
NEGA
TIVE
3
12
63
53
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
THW
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
A4
1 of
1
100-
0649
618
/01/
2006
BE
TA16
(BZ6
02)H
EA
TE
XCH
AN
GE
TW
TMC
40 G
EA
RB
OX
00
32
8 M
10 X
50
BOLT
SEQ
UI-
SPAC
ED O
NAN
82.
5mm
PCD
FLEX
IBLE
COU
LPIN
G DE
TAILS
FLEX
IBLE
MOU
NTDE
TAILS
100
120
63
65M
IN90
.0M
AX
F.W
FIL
LER
CAP
OIL
FIL
TER
SEA
WAT
ER P
UM
PIN
LET O
22m
m M
ALE
STU
B
LUBE
OIL
DIPS
TICK
FUEL
FIL
TER
TO C
ALOR
IFIE
R5/
8" B
SP B
ORE
HOS
E
FUEL
INTA
KE8m
m H
OSE
TAIL
45Am
p12
VAL
TERN
ATOR
GEAR
BOX
OUTP
UT O
63.5
H8
4 HO
LES
O10
.5 T
HRU
SACR
IFIC
IAL
ANOD
E
SUM
P PI
CK U
P ON
SHAL
LOW
SU
MP
ONLY
BATT
ERY
POSI
TIVE
BATT
ERY
NEGA
TIVE
OIL
FIL
LER
CAP
FUEL
BLE
ED S
CREW
GEAR
BOX
OIL
FIL
LERGE
ARBO
XO
IL D
IPST
ICK
AIR
FILT
ER
SUM
P PU
MP
FROM
CAL
ORIF
IER
5/8"
BSP
BOR
E HO
SE
FUEL
RET
URN
8mm
HOS
E TA
IL
67.5 63
12
294
182
WIT
H SH
ALLO
W S
UM
P
223±3
340
185
185
137
3
223
185185
159
258
597
212
O82.5
O82
.5
50O
54
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
THW
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
A4
1 of
1
100-
9961
020
/12/
2005
BD
722
HE
AT
EXC
HA
NG
E
TW
TMC
40 G
EA
RB
OX
03
32
8 M
10 X
50
BOLT
SEQ
UI-
SPAC
ED O
NAN
82.
5mm
PCD
FLEX
IBLE
COU
LPIN
G DE
TAILS
FLEX
IBLE
MOU
NTDE
TAILS
100
120
63
65M
IN90
.0M
AX
GEAR
BOX
OUTP
UT O
63.5
H8
4 HO
LES
O10
.5 T
HRU
F.W
FIL
LER
CAP
OIL
FIL
TER
SEA
WAT
ER P
UM
PIN
LET O
22m
m M
ALE
STU
B
LUBE
OIL
DIPS
TICK
FUEL
FIL
TER
TO C
ALOR
IFIE
R5/
8" B
SP B
ORE
HOS
E
FUEL
INTA
KE8m
m H
OSE
TAIL
45Am
p12
VAL
TERN
ATOR
SACR
IFIC
IAL
ANOD
E
SUM
P PI
CK U
P ON
SHAL
LOW
SU
MP
ONLY
BATT
ERY
POSI
TIVE
BATT
ERY
NEGA
TIVE
OIL
FIL
LER
CAP
FUEL
BLE
ED S
CREW
GEAR
BOX
OIL
FIL
LERGE
ARBO
XO
IL D
IPST
ICK
AIR
FILT
ERSU
MP
PUM
P
FROM
CAL
ORIF
IER
5/8"
BSP
BOR
E HO
SE
FUEL
RET
URN
8mm
HOS
E TA
IL
67.5 63
294
12
182
WIT
H SH
ALLO
W S
UM
P
250±3340
50O
137
185
185
3
218
223
185 185
159
316
655
NEW
TIT
LE B
LOCK
18-0
5-04
02FU
EL F
ILTER
, H/E
TAN
K AN
D AI
R FI
LTER
25-0
7-05
03CA
LORI
FIER
S AN
D TI
ER2
CLOS
ED B
REAT
HER
20/12
/05
LTTW
LTTW TW
O82
.5
O82
.5
55
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
THW
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
A4
1 of
1
100-
0104
820
/12/
2005
BD
722
HE
AT
EXC
HA
NG
E
TW
PR
M80
GE
AR
BO
X
03
32
8 M
10 X
50
BOLT
SEQ
UI-
SPAC
ED O
NAN
82.
5mm
PCD
FLEX
IBLE
COU
LPIN
G DE
TAILS
FLEX
IBLE
MOU
NTDE
TAILS
100
120
63
65M
IN90
.0M
AX
F.W
FIL
LER
CAP
OIL
FILT
ER
SEA
WAT
ER P
UM
PIN
LET O
22m
m M
ALE
STU
B
LUBE
OIL
DIPS
TICK
FUEL
FIL
TER
TO C
ALOR
IFIE
R5/
8" B
SP B
ORE
HOS
E
FUEL
INTA
KE8m
m H
OSE
TAIL
45Am
p12
VAL
TERN
ATOR
185
185
3
223
218
SACR
IFIC
IAL
ANOD
E
SUM
P PI
CK U
P ON
SHAL
LOW
SU
MP
ONLY
BATT
ERY
POSI
TIVE
BATT
ERY
NEGA
TIVE
329
9272
50O
250±334018
2W
ITH
SHAL
LOW
SU
MP
OIL
FIL
LER
CAP
FUEL
BLE
ED S
CREW
GEAR
BOX
OIL
FIL
LER
& DI
PSTI
CK
AIR
FILT
ER
SUM
P PU
MP
FROM
CAL
ORIF
IER
5/8"
BSP
BO
RE H
OSE
FUEL
RET
URN
8mm
HOS
E TA
IL
195
316
691
GEAR
BOX
OUTP
UT
O82
.5
O63
.5563
.504
HOLE
SO
10.5
THR
U
137
02BA
TTER
Y CO
NNEC
TION
S AN
D W
ASTI
NG A
NODE
08-1
2-05
03
FUEL
FILT
ER, T
ANK
AND
AIR
FILT
ER25
/07/
05
LTTW TW
LT
CALO
RIFI
ERS
AND
TIER
2 CL
OSED
BRE
ATHE
R20
/12/0
5TW
O82
.5
56
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
THW
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
A4
1 of
1
100-
0574
920
/12/
2005
BD
722
KE
EL
CO
OLE
D
TW
PR
M80
GE
AR
BO
X
03
32
8 M
10 X
50
BOLT
SEQ
UI-
SPAC
ED O
NAN
82.
5mm
PCD
FLEX
IBLE
COU
LPIN
G DE
TAILS
FLEX
IBLE
MOU
NTDE
TAILS
100
120
63
65M
IN90
.0M
AX
GEAR
BOX
OUTP
UT
O63
.5563
.504
HOLE
SO
10.5
THR
U
O82
.5
F.W
FIL
LER
CAP
O IL
FILT
ER
LUBE
OIL
DIPS
TICK
FUEL
FIL
TER
TO C
ALO
RIFI
ER5/
8" B
SP B
ORE
HOS
E
FUEL
INTA
KE8m
m H
OSE
TAIL
45Am
p12
VAL
TERN
ATOR
FROM
KEE
L CO
OLER
(WAT
ER R
ETU
RN)
22 ID
HOS
E RE
QUIR
ED
TO K
EEL
COOL
ER(W
ATER
FLO
W)
22 ID
HOS
E RE
QUIR
ED
OIL
FIL
LER
CAP
FUEL
BLE
ED S
REW
GEAR
BOX
OIL
FILL
ER&
DIPS
TICK
AIR
FILT
ER
SUM
P PU
MP
FUEL
RET
URN
8mm
HOS
E TA
IL
FROM
CAL
ORIF
IER
5/8"
BSP
BO
RE H
OSE
SUM
P PI
CK U
P ON
SHAL
LOW
SU
MP
ONLY
BATT
ERY
POSI
TIVE
BATT
ERY
NEGA
TIVE
250±334018
2W
ITH
SHAL
LOW
SU
MP
330
9272
195
316
691
185
185
137
O82
.5
02AD
DED
NOTE
S08
-12-
05
03
FUEL
FILT
ER, T
ANK
AND
AIR
FILT
ER25
/10/0
5
DMTW TW
LT
CALO
RIFI
ERS
AND
TIER
2 CL
OSED
BRE
ATHE
R21
/12/0
5TW
1 1/
2 BS
P EX
HAU
ST
216
235
57
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
THW
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
A4
1 of
1
100-
0649
519
/01/
2006
BE
TA25
(BD
902)
HE
AT
EXC
HN
AG
E
TW
TMC
40 G
EA
RB
OX
01
32
8 M
10 X
50
BOLT
SEQ
UI-
SPAC
ED O
NAN
82.
5mm
PCD
FLEX
IBLE
COU
LPIN
G DE
TAILS
FLEX
IBLE
MOU
NTDE
TAILS
100
120
63
65M
IN90
.0M
AX
GEAR
BOX
OUTP
UT O
63.5
H8
4 HO
LES
O10
.5 T
HRU
F.W
FIL
LER
CAP
OIL
FIL
TER
SEA
WAT
ER P
UM
PIN
LET O
22m
m M
ALE
STU
B
LUBE
OIL
DIPS
TICK
FUEL
FIL
TER
TO C
ALO
RIFI
ER5/
8" B
SP B
ORE
HOS
E
FUEL
INTA
KE8m
m H
OSE
TAIL
45Am
p12
VAL
TERN
ATOR
185
185
137
3
216
223
SACR
IFIC
IAL
ANOD
E
SUM
P PI
CKU
P ON
SHAL
LOW
SU
MP
ONLY
BATT
ERY
POSI
TIVE
BATT
ERY
NEGA
TIVE
68 63
294
182
WIT
H SH
ALLO
W S
UM
P
223±3
340
50O
OIL
FIL
LER
CAP
FUEL
BLE
E D S
CREW
GEAR
BOX
OIL
FILL
ER
GEAR
BOX
OIL
DIP
STIC
K
AIR
FILT
ER
SUM
P PU
MP
FROM
CAL
ORIF
IER
5/8"
BSP
BO
RE H
OSE
FUEL
RET
URN
8mm
HOS
E TA
IL
159
338
677
O82
.5
O82
.5
CALO
RIFI
ERS
AND
SHAL
LOW
SUM
P19
/01/0
6TW
58
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
THW
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
A4
1 of
1
100-
0650
923
/01/
2006
BE
TA25
(BD
902)
HE
AT
EXC
HA
NG
E
TW
PR
M12
0G
EA
RB
OX
01
32
8 M
10 X
50
BOLT
SEQ
UI-
SPAC
ED O
NAN
82.
5mm
PCD
FLEX
IBLE
COU
LPIN
G DE
TAILS
FLEX
IBLE
MOU
NTDE
TAILS
100
120
63
65M
IN90
.0M
AX
O82
.5
GEAR
BOX
OUTP
UT
O82
.5
4 HO
LES
O10
.5 T
HRU
O63
.5H8
F.W
FIL
LER
CAP
OIL
FILT
ER
SEA
WAT
ER P
UM
PIN
LET O
22m
m M
ALE
STU
B
LUBE
OIL
DIPS
TICK
FUEL
FIL
TER
TO C
ALO
RIFI
ER5/
8" B
SP B
ORE
HOS
E
FUEL
INTA
KE8m
m H
OSE
TAIL
45 A
mp
12V
ALTE
RNAT
OR
185
18513
7
216
223
72
223±3
340
182
WIT
H SH
ALLO
W S
UM
P
92
350
SUM
P PI
CK U
P ON
SHAL
LOW
SU
MP
ONLY
BATT
ERY
POSI
TIVE
BATT
ERY
NEGA
TIVE
50O
216
33873
4
OIL
FIL
LER
CAP
FUEL
BLE
ED S
CREW
GEAR
BOX
OIL
FIL
LER
AND
DIPS
TICK
AIR
FILT
ER
SUM
P PU
MP
FROM
CAL
ORIF
IER
5/8"
BSP
BO
RE H
OSE
FUEL
RET
URN
8mm
HOS
E TA
IL
CALO
RIFI
ERS,
SHAL
LOW
SUM
P AN
D CO
UPLIN
G DE
TAILS
23/0
1/06
TW
59
01
BE
TA M
ARIN
E L
TD,
ME
RR
ETT
S M
ILLS
,B
ATH
RO
AD
,S
OU
THW
OO
DC
HE
STE
R,
STR
OU
D, G
LOS
. GL5
5E
U
DO
NO
T S
CA
LED
IME
NS
ION
S IN
MM
(IN
CH
)
BE
TAM
AR
INE
TEL:
(014
53)8
3528
2FA
X:(
0145
3)83
5284
RE
VD
ES
CR
IPTI
ON
NO
TES
AP
P'D
DA
TED
RA
WN
DR
AW
N B
Y:-
CH
EC
KED
BY
:-S
CA
LEP
AG
E
SIZ
E
TITL
E
DW
G N
O.
DA
TE
RE
V
A4
1 of
1
100-
0649
423
/01/
2006
BE
TA25
(BD
902)
HE
AT
EXC
HA
NG
E
TW
KA
NZA
KIT
TMC
35A
GE
AR
BO
X
01
8 M
10 X
50
BOLT
SEQ
UI-
SPAC
ED O
NAN
78
PCD
FLEX
IBLE
COU
LPIN
G DE
TAILS
FLEX
IBLE
MOU
NTDE
TAILS
100
120
63
65M
IN90
.0M
AX
F.W
FIL
LER
CAP
OIL
FILT
ER
SEA
WAT
ER P
UM
PIN
LET O
22m
m M
ALE
STU
B
LUBE
OIL
DIPS
TICK
FUEL
FIL
TER
TO C
ALOR
IFIE
R5/
8" B
SP B
ORE
HOS
E
FUEL
INTA
KE8m
m H
OSE
TAIL
45 A
mp
12V
ALTE
RNAT
OR
SACR
IFIC
IAL
ANO
DE
SUM
P PI
CK U
P ON
SHAL
LOW
SU
MP
ONLY
BATT
ERY
POSI
TIVE
BATT
ERY
NEGA
TIVE
OIL
FIL
LER
CAP
FUEL
BLE
ED S
CREW
GEAR
BOX
OIL
FILL
ERAN
D DI
PSTI
CK
AIR
FILT
ER
SUM
P PU
MP
FROM
CAL
ORIF
IER
5/8"
BSP
BOR
E HO
SE
FUEL
RET
URN
8mm
HOS
E TA
IL
CALO
RIFI
ERS,
SHAL
LOW
SUM
P AN
D CO
UPLIN
G DE
TAILS
23/0
1/06
TW
GEAR
BOX
OU
TPU
T
O50
O78.0
4 HO
LES
O10
.5 T
HRU
O78
.0
32
185
185
137
216
223
79.5
223±3
182
WIT
H SH
ALLO
W S
UM
P
340
7°
50O
352
65
217
33873
5
60
61
Emission durability. IN RESPECT TO THE RECREATIONAL CRAFT DIRECTIVE 94/25/EC AND AMENDMENT2003/44/EC ANNEX 1, B3.
The engine must be installed, maintained and operated within the parameters detailed in theOperator’s Maintenance Manual. Maintenance must use approved materials, parts andconsumables. Should the engine lie unused for a period in excess of 6 months it must beinhibited otherwise it will deteriorate with resulting decrease in performance. See also theWinterising and Laying Up procedures in the Operator’s Maintenance Manual.
The fuel settings of the diesel injection system must not be tampered with otherwise theguarantee will be invalid and the performance may fall outside prescribed limit. Suchadjustment cannot be allowed under the terms of the emission certification.
Performance of the engine depends upon the use of correct fuels, lubricants and inhibitors.These are fully detailed in the Operator’s Maintenance Manual.
Particular attention must be paid to the installation with respect to the exhaust system. Thesystem must be designed so that water cannot back feed into the engine. The run must besuch that the back pressure at the engine manifold does not exceed the level detailed in theOperator’s Maintenance Manual. Wet, water injected, exhaust systems must be at least thebore mentioned in the Operator’s Maintenance Manual and should the run be excessive thisbore must be increased accordingly. Back pressure is measured at the outlet of the enginemanifold before the water injection bend or dry bellows.
Our experience over 14 years has shown that properly installed and maintained engines holdtheir performance without major mishap even when running hours exceed those mentioned inthe Recreational Craft Directive. It is the owners / users responsibility to ensure that the enginecontinues to function properly and any malfunction must be immediately investigated. TheTrouble Shooting section as detailed in the Operator’s Maintenance Manual is particularlyhelpful in this respect. Engine performance, especially with respect to erratic running, exhaustcondition, low power output and high oil consumption are indications of engine conditionsthat may result in emissions outside the prescribed limits and must therefore be investigatedand rectified immediately.
62
63
QUICK REFERENCE PARTS LISTINGHeat Exchanger & Keel Cooled Beta 10, BZ482, Beta 16, BD722, & Beta 25
In all cases please quote Beta Marine WOC “K” number and Engine Type
Description Part Number Qty per EngineAlarm board 200-04655 1
Relay 12 Volt 40A (28Ra) fitted to rear of panels 200-87020 1
Stop Solenoid (energised to stop fuel) 600-81950 1
Fuse (Blade) 40 Amp 200-00959 1
Standard Engine Harness 200-98380/01 1
65 Amp Alternator Sub Loom (external fan) 200-01196
1
1m Panel Extension Loom 200-04588/01
2m Panel Extension Loom 200-04588/02
3m Panel Extension Loom 200-04588/03
4m Panel Extension Loom 200-04588/04
Water Temperature Switch (Panel A, ABV & ABVW) NOT Beta 16 or 25 200-01133
1Water Temperature Switch with single terminal Beta 16 & Beta 25) 600-62820
Water Temperature Sender (Panel C & B) 200-94360
Oil Pressure Switch (Panel A, ABV, ABVW, & B) 600-626701
Oil Pressure Sender (Panel C) 200-94350
Standard 50mm Water Injection Exhaust Bend 202-024581
5” High Rise 50mm Water Injection Exhaust Bend 202-92400/22
Exhaust Bend Gasket 600-62620 1
Drive Plate 22-B-60 - PRM / ZF 206-919501
Drive Plate 22-B-4 - TMC / ZF 206-97041
Flexible Mountings (Trelleborg RA60) 213-93440 4
Rocker Cover Gasket BZ482 600-01055
1Rocker Cover Gasket Beta 16 600-05467
Rocker Cover Gasket BD722 600-00607
Rocker Cover Gasket Beta 25 600-05468
Head Gasket Beta 10, BZ482 600-00409
1Head Gasket Beta 16 600-05469
Head Gasket BD722 600-01562
Head Gasket Beta 25 600-05470
Top Gasket Set BZ482 600-00383
1Top Gasket Set Beta 16 600-05471
Top Gasket Set BD722 600-00395
Top Gasket Set Beta 25 600-05472
Lower Gasket Set BZ482 600-01056
1Lower Gasket Set Beta 16 600-05473
Lower Gasket Set BD722 600-00394
Lower Gasket Set Beta 25 600-05474
Manuals
Operators Maintenance Manual 221-02887 1
Kubota Workshop Manual, Beta 10 / BZ482, BD722 600-007561
Kubota Workshop Manual, Beta 16 & Beta 25 600-05475
Kubota Spare Parts Manual - Beta 10 & BZ482 600-02437
1Kubota Spare Parts Manual – Beta 16 600-05476
Kubota Spare Parts Manual – BD722 600-02438
Kubota Spare Parts Manual - Beta 25 600-05477
64
QUICK REFERENCE PARTS LISTINGHeat Exchanger & Keel Cooled Beta 10, BZ482, Beta 16, BD722, & Beta 25
In all cases please quote Beta Marine WOC “K” number and Engine Type
Description Part Number Qty per EngineWasting Zinc Anode 209-61840 1
Heat Exchanger “O” Ring 209-80110 2
Pressure Cap 95kPa 209-80130 1
Thermostat 600-59290 1
Thermostat (Beta 16 & 25 only) 600-72450
Thermostat Gasket 600-62590 1
Thermostat Gasket (Beta 16 & 25 only) 600-80490
Fuel Filter 211-60210 1
Air Filter Element 211-62950 1
Lubricating Oil Filter 211-63760 1
Sump Pump 201-80061 1
Sump Pump Clamp 212-00793 2
Dip Stick (only) - Extended 600-96280 1
Sea Water Pump Johnson (6 Screw) 207-61500/01
Sea Water Pump Impeller Kit Johnson 6 Screw (includes gasket etc.) 207-05355 1
Sea Water Pump Cover plate Johnson 6 Screw 207-05478 1
Sea Water Pump cover plate Bolt Johnson 6 Screw 207-05479 6
Fuel Lift Pump 600-65470 1
Fuel Lift Pump – Beta 16 & 25 AK/MINI/9&6/F0I
Fuel Lift Pump Gasket 600-00065 1
Belt – Standard “Vee” – 40 Amp 600-63080
Correctly
Select
a
Belt
Belt – PolyVee 40 Amp 4PK900 (NOT Beta 25) 214-04360
Belt – PolyVee 40 Amp 4PK913 Beta 25 214-05074
Belt – 65 Amp Alternator BZ482/BD722 - 4PK950 – External fan 214-03235
Belt – 65 Amp Alternator Beta 16 - 4PK900 – Internal fan 212-04360
Belt – 65 Amp Alternator Beta 25 4PK913 Internal fan 214-05074
Alternator 40 Amp 600-80010
1Alternator 55 Amp - (A127) 200-69190
Alternator 65 Amp – External Fan 200-01155
Alternator 65 Amp – Internal Fan 200-04989
Panel A - standard AK/2AS/KS01
1
Panel ABV with tachometer AK/2ABV/KS01
Panel ABVW with tachometer AK/2ABVW/KS01
Panel B – with tachometer and gauge AK/2BT/KS01
Panel C – with tachometer and three gauges AK/2CD/KS01
Control Panel standard Key 600-00058 1
Control Panel Key Switch 600-00057 1
Control Panel Stop Button (and heat & start on ABVW) 200-00072 1
Tachometer 0-4000rpm with digital hour counter 200-02373 1
Water temperature switch Gauge (B & C panels) 200-96200 1
Oil pressure switch Gauge (C panels only) 200-96190 1
Voltmeter (C panels only) 200-96210 1
Green power on indicator lamp & retaining clip 200-04656 1
Red warning indicator lamp & retaining clip 200-04657 3 or 4
65
Service Record
Service Date Responsible
1 Commissioned
2 First 25 hours
3 First 50 hours
4 Every 150 hours with Shallow sump
5 Every Year / Every 250 hours if sooner
6
7
8
9 Every 750 hours
10
11
12
13
14
15
Beta Marine LimitedDavy Way, Waterwells, Quedgeley, Gloucester GL2 2AD, U.K.
Tel: 01452 723492Fax: 01452 883742
www.betamarine.co.ukTechnical Spares email: [email protected] Warranty email: [email protected]
Keel Cooled 10 to 90bhp Beta Marine Generating Sets 3.7 to 40kVA
Beta Marine Generating Sets 30 to 900kVA
Sail Drives 13.5 to 50bhp
Heat Exchanger Cooled 10 to 90bhp
Ref: 1590
ww
w.m
ono-
stud
io.c
o.uk