OPERATION AND PARTS MANUAL - Multiquip Inc

OPERATION AND PARTS MANUAL

SERIESHPLA/HPHA-SERIES 46"

MODELS:HPLA46411HHPHA46411H

WALK-BEHIND TROWEL(Honda GX340K1QAP2 Gasoline Engine)

P/N 20914

Revision #6 (07/06/10)

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

To find the latest revision of thispublication, visit our website at:

www.multiquip.com

Engine exhaust and some ofits constituents, and some dust created

of California to cause cancer, birthdefects and other reproductive harm.

by power sanding, sawing, grinding,drillingandotherconstructionactivitiescontains chemicals known to the State

Some examples of these chemicals are:

Leadfromlead-basedpaints.Crystallinesilicafrombricks.Cementandothermasonryproducts.Arsenicandchromiumfromchemicallytreatedlumber.

Your risk from these exposures varies,dependingonhowoftenyoudothistypeof work. To reduce your exposure tothese chemicals: work in aALWAYSwell ventilated area, and work withapproved safety equipment, such asdust masks that are specially designedto filter out microscopic particles.

HPLA/HPHA-SERIES 46" TROWEL— PROPOSITION 65 WARNING

HPLA/HPHA-SERIES 46" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #6 (07/06/10) — PAGE 3

NOTE PAGE

— HPLA/HPHA-SERIES 46" WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #6 (07/06/10)

HPLA/HPHA-SERIES 46" TROWEL— TABLE OF CONTENTS

Proposition 65 Warning ............................................. 2Table Of Contents ..................................................... 4Parts Ordering Procedures ....................................... 5Training Checklist ...................................................... 6Daily Pre-Operation Checklist ................................... 7Safety Message Alert Symbols .............................. 8-9Rules For Safe Operation .................................. 10-11Operation And Safety Decals .................................. 12Specifications (Trowel) ............................................ 13Specifications (Engines).......................................... 14General Information ................................................ 15

MQ WHITEMAN — HPLA/HPHASERIES 46" TROWELControls and Components ................................. 16-17Basic Engine ........................................................... 18Assembly and Installation .................................. 19-21Pre-Inspection .................................................... 22-23Initial Start-Up (Gasoline Engine) ...................... 24-25Operation ........................................................... 26-27Options ............................................................... 28-29Maintenance (Engine) ........................................ 30-31Maintenance (Trowel) ........................................ 32-36Troubleshooting (Trowel) ................................... 37-38Troubleshooting (Engine) ................................... 38-39Explanation of Codes In Remarks Column ............. 40Suggested Spare Parts ........................................... 41Nameplate and Decals....................................... 42-43Standard Handle Assembly ............................... 44-45Quick Pitch™ Handle Assembly........................ 46-494-Blade Spider Assembly ................................... 50-51Gearbox & Engine Mounts Assembly ................ 52-55Engine Assembly ............................................... 56-57Guard Ring Assembly ........................................ 58-59Stabilizer Ring Assembly ................................... 60-61Blades and Arm Adjustment Fixture Assembly .. 62-63Lifting Bail Assembly (Option) ............................ 64-65

Honda GX340K1QAP2 EngineAir Cleaner Assembly ......................................... 66-67Camshaft Assembly ........................................... 68-69Carburetor Assembly ......................................... 70-71Crankcase Cover Assembly ............................... 72-73Control Assembly ............................................... 74-75Cylinder Barrel Assembly ................................... 76-77Cylinder Head Assembly .................................... 78-79Crankshaft Assembly ......................................... 80-81Fan Cover Assembly .......................................... 82-83Flywheel Assembly ............................................ 84-85Fuel Tank Assembly ........................................... 86-87Ignition Coil Assembly ........................................ 88-89Muffler Assembly ............................................... 90-91Piston Assembly ................................................. 92-93Recoil Starter Assembly..................................... 94-95Labels Assembly ................................................ 96-97

Terms and Conditions of Sale — Parts ................... 98

Specification and part numberare subject to change withoutnotice.

NOTE


ww

w.m

ultiq

uip

.com

Ordering parts has never been easier! Choose from three easy options:

WE ACCEPT ALL MAJOR CREDIT CARDS!

When ordering parts, please supply: Dealer Account Number Dealer Name and Address Shipping Address (if different than billing address) Return Fax Number Applicable Model Number Quantity, Part Number and Description of Each Part

Specify Preferred Method of Shipment:UPS/Fed Ex DHL

Priority One Truck Ground

Next Day Second/Third Day

If you have an MQ Account, to obtain a Username and Password, E-mail us at: [email protected].

To obtain an MQ Account, contact your District Sales Manager for more information.

Order via Internet (Dealers Only):Order parts on-line using Multiquip’s SmartEquip website! View Parts Diagrams Order Parts Print Specification Information

Note: Discounts Are Subject To Change

Goto www.multiquip.com and click on Order Parts to log in and save!

Use the internet and qualify for a 5% Discount on Standard orders for all orders which include complete part numbers.*

Order via Fax (Dealers Only):All customers are welcome to order parts via Fax.Domestic (US) Customers dial: 1-800-6-PARTS-7 (800-672-7877)

Fax your order in and qualify for a 2% Discount on Standard orders for all orders which include complete part numbers.*

Order via Phone: Domestic (US) Dealers Call: 1-800-427-1244

Best Deal!

International Customers should contact their local Multiquip Representatives for Parts Ordering information.

Non-Dealer Customers: Contact your local Multiquip Dealer for parts or call 800-427-1244 for help in locating a dealer near you.

Note: Discounts Are Subject To Change

Effective: January 1st, 2006

NOTICE

All orders are treated as Standard Orders and will ship the same day if received prior to 3PM PST.

PARTS ORDERING PROCEDURES


TRAINING CHECKLIST

This checklist will lists some of the minimum requirements formachine maintenance and operation. Please feel free to detachit and make copies. Use this checklist whenever a new operatoris to be trained or it can be used as a review for more experiencedoperator’s.

Operator _________________________________________ Trainee __________________________________________

COMMENTS:

HPLA/HPHA-SERIES 46" TROWEL— TRAINING CHECKLIST

TSILKCEHCGNINIART

.ON NOITPIRCSED ?KO ETAD

1 .yletelpmoclaunaMs’rotarepOdaeR

2 dnaenignefognikcehc,stnenopmocfonoitacol,tuoyalenihcaM.leveldiulfxobraeg

3 .erudecorpgnileufer,metsysleuF

4 .)gninnurtonenihcam(slortnocfonoitarepO

5 .noitarepohctiwspotsytefas,slortnocytefaS

6 .serudecorppotsycnegremE

7 .enihcamfoputratS

8 .gnirevuenaM

9 .gnihctiP

01 .seuqinhcetgnihsinifetercnoC

11 .enihcamfonwodtuhS

21 .enihcamfognitfiL

31 .egarotsdnatropsnartenihcaM


DAILY PRE-OPERATION CHECKLIST

COMMENTS:

HPLA/HPHA-SERIES 46" TROWEL— DAILY PRE-OPERATION CHECKLIST

TSILKCEHCNOITAREPO-ERPYLIAD

1 .leveLliOenignE

2 .leveLdiulFxobraeG

3 .sedalBfonoitidnoC

4 .noitarepOhctiPedalB

5 .noitarepOhctiwSpotSytefaS

6 .noitarepOhctulCtleB-V


HPLA/HPHA-SERIES 46" TROWEL— SAFETY MESSAGE ALERT Y SYMBOLS

Safety precautions should be followed at all times when operatingthis equipment. Failure to read and understand the SafetyMessages and Operating Instructions could result in injury toyourself and others.

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

This Owner's Manual has been developed to providecomplete instructions for the safe and efficient operationof the Multiquip HPLA/HPHA-SERIES 46" WALK-BEHIND TROWEL. For engine maintenanceinformation, please refer to the engine manufacturersinstructions for data relative to its safe operation.Before using this WALK-BEHIND TROWEL, ensurethat the operating individual has read andunderstands all instructions in this manual.

NOTE

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform youabout potential hazards that could injure you or others. TheSafety Messages specifically address the level of exposure tothe operator, and are preceded by one of three words: DANGER,WARNING, or CAUTION.

DANGER: You WILL be KILLED orSERIOUSLY injured if you DO NOT followdirections.

WARNING: You CAN be KILLED orSERIOUSLY injured if you DO NOT followdirections.

CAUTION: You CAN be injured if youDO NOT follow directions.

HAZARD SYMBOLS

Engine exhaust gases contain poisonouscarbon monoxide. This gas is colorless andodorless, and can cause death if inhaled.NEVER operate this equipment in a confinedarea or enclosed structure that does notprovide ample free flow air.

Potential hazards associated with trowel operation will bereferenced with "Hazard Symbols" which appear throughoutthis manual, and will be referenced in conjunction with Safety"Message Alert Symbols".

Gasoline is extremely flammable, and itsvapors can cause an explosion if ignited. DONOT start the engine near spilled fuel orcombustible fluids. DO NOT fill the fuel tankwhile the engine is running or hot. DO NOToverfill tank, since spilled fuel could ignite if itcomes into contact with hot engine parts orsparks from the ignition system. Store fuel inapproved containers, in well-ventilated areasand away from sparks and flames. NEVERuse fuel as a cleaning agent.

Burn Hazards

Engine components can generate extreme heat.To prevent burns, DO NOT touch these areaswhile the engine is running or immediately afteroperations. NEVER operate the engine withheat shields or heat guards removed.

Rotating Parts

NEVER operate equipment with covers, orguards removed. Keep fingers, hands, hairand clothing away from all moving parts toprevent injury.

Explosive Fuel

Lethal Exhaust Gases


Accidental Starting

ALWAYS place the engine ON/OFFswitch in the OFF position, when thetrowel is not in use.

Over Speed Conditions

NEVER tamper with the factory settings of theengine governor or settings. Personal injuryand damage to the engine or equipment canresult if operating in speed ranges abovemaximum allowable.

Respiratory Hazard

ALWAYS wear approved respiratory protection.

ALWAYS wear approved eye and hearingprotection.

Sight and Hearing hazard

Equipment Damage Messages

Other important messages are provided throughout this manualto help prevent damage to your trowel, other property, or thesurrounding environment.

HPLA/HPHA-SERIES 46" TROWEL— SAFETY MESSAGE ALERT SYMBOLS

This walk-behind trowel, otherproper ty, or the surroundingenvironment could be damaged ifyou do not follow instructions.

NOTE


CAUTION:Failure to follow instructions in this manualmay lead to serious injury or even death! Thisequipment is to be operated by trained andqualified personnel only! This equipment isfor industrial use only.

The following safety guidelines should always be used whenoperating the HPLA/HPHA-SERIES 46" walk-behind trowel.

SAFETY

■ DO NOT operate or service this equipmentbefore reading this entire manual.

■ This equipment should not be operated bypersons under 18 years of age.

■ NEVER operate the trowel without proper protective clothing,shatterproof glasses, steel-toed boots and other protectivedevices required by the job.

■ NEVER operate this equipment when notfeeling well due to fatigue, illness or takingmedicine.

■ NEVER operate the trowel under theinfluence or drugs or alcohol.

■ NEVER use accessories or attachments, which are notrecommended by Multiquip for this equipment. Damage tothe equipment and/or injury to user may result.

■ Manufacturer does not assume responsibility for any accidentdue to equipment modifications.

■ Whenever necessary, replace nameplate, operation andsafety decals when they become difficult read.

■ ALWAYS check the trowel for loosened threads or boltsbefore starting.

■ ALWAYS use extreme caution whenworking with flammable liquids. Whenrefueling, stop the engine and allow itto cool.

■ NEVER smoke around or near themachine. Fire or explosion could result fromfuel vapors, or if fuel is spilled on a hot!engine.

■ NEVER operate the trowel in an explosive atmosphere ornear combustible materials. An explosion or fire could resultcausing severe bodily harm or even death.

■ Topping-off to filler port is dangerous, as it tends to spill fuel.

■ NEVER touch the hot exhaustmanifold, muffler or cylinder. Allowthese parts to cool before servicingthe trowel.

■ The engine of this trowel requires an adequate free flow ofcooling air. NEVER operate the trowel (except electric models)

in any enclosed or narrowarea where free flow of theair is restricted. If the air flowis restricted it will causeserious damage to thetrowel's engine and maycause injury to people.Remember the trowel'sengine gives off DEADLYcarbon monoxide gas.

■ High Temperatures – Allow the engine to cool before addingfuel or performing service and maintenance functions. Contactwith hot! components can cause serious burns.

■ ALWAYS refuel in a well-ventilated area, away from sparksand open flames.

HPLA/HPHA-SERIES 46" TROWEL— RULES FOR SAFE OPERATION


HPLA/HPHA-SERIES 46" TROWEL— RULES FOR SAFE OPERATION

■ DO NOT operate this trowel unless all guards and safetydevices are attached and in place. See pages 16 and 17.

■ ALWAYS use proper lifting techniques when moving thetrowel. See page 24.

■ ALWAYS check to make sure that the operating area is clearbefore starting the engine.

■ ALWAYS test the safety stop switch devices beforeoperating the trowel.

■ NEVER place your feet or hands inside the guard ringswhile starting or operating this equipment.

■ AVOID wearing jewelry or loose fitting clothing that may snagon the controls or moving parts, this can cause a seriousinjury.

■ ALWAYS keep clear of rotating or moving parts whileoperating the trowel.

■ NEVER leave the machine unattended while running.

■ Moving Parts – Shut down the engine before performingservice or maintenance functions. Contact with moving partscan cause serious injury.

Maintenance Safety

■ Disconnect the spark plug wires before attempting any typeof service.

■ Securely support any machine components that must beraised.

■ NEVER lubricate components or attempt service on a runningmachine.

■ DO NOT use food or plastic containers to dispose ofhazardous waste.

■ DO NOT pour waste, oil or fuel directly onto the ground,down a drain or into any water source.

CAUTIONCAUTIONCAUTIONCAUTIONCAUTION

■ Keep the trowel in proper running condition.

■ Make sure that there is no buildup of concrete, grease, oil ordebris on the trowel.

■ Fix damage to the trowel immediately and always replacebroken parts.

■ Dispose of hazardous waste properly. Examples of potentiallyhazardous waste are used motor oil, fuel and fuel filters.

■ High Temperatures – Allow the machine and engine tocool before adding fuel or performing service andmaintenance functions. Contact with hot! components cancause serious burns.

EMERGENCIES

■ ALWAYS know the location ofthe nearest fire extinguisher.

■ ALWAYS know the location of thenearest and first aid kit.

■ In emergencies always know the location of thenearest phone or keep a phone on the job site.Also know the phone numbers of the nearestambulance, doctor and fire department. Thisinformation will be invaluable in the case of anemergency.


HPLA/HPHA-SERIES 46" TROWEL— OPERATION AND SAFETY DECALS

Machine Safety Decals

The HPLA/HPHA-SERIES 46" walk-behind trowel is equipped with a number of safety decals. These decals are provided foroperator safety and maintenance information. (Figure 1) below illustrates these decals as they appear on the machine. Should anyof these decals become unreadable, replacements can be obtained from your dealer.

Figure 1. HPLA/HPHA-SERIES 46" Trowel Decals

P/N 20526

BOISE, IDAHO USA

U. S. PATENTXXXXXXX

QUICK - PITCH™ HANDLE

CONCRETE FINISHER

CO

NCRETE FLOOR

FINISHER

BOISE, IDAHOUSA

Q U I C K

P I T C H

P/N 12405 P/N 1492

P/N1499

FINISH J COMBO

PRELOAD TRIM INDICATORFINISH B COMBO

P/N 1735

P/N 1758

Symbol indicates that it is mandatory to wearsafety glasses, safety helmet and ear protection.

Symbol indicates that it is mandatory towear safety shoes, with extra protection(steel toed).

This is the symbol for belt drive.

This is the symbol for gear drive.

Radiating heat symbol. Symbol indicates equipmentis hot.

Symbol for examining or checking of the machine.Mostly used for maintenance. Check lubricationoil in gearbox.

Symbol indicates that it is mandatory to weargloves.

P/N 11247 (Part of decal kit 12620)







CONTACT MULTIQUIPSERVICE DEPT.

NAMEPLATE

DO NOT OPERATE HANDLE UNTIL IT ISSECURELY FASTENED TO POWER TROWEL

& INSTRUCTIONS HAVE BEEN READ

INJURY COULD RESULT IF FINISHER IS LIFTEDWITHOUT PITCH HANDLE FIRMLY ENGAGE

WARNING!

WARNING!

DO NOT LIFT MACHINERY BY GUARDRING. MAY CAUSE DAMAGE TOGUARD RING SHOCK MOUNTS

USE LIFT HANDLES ONLY

CAUTION

P/N 1261

P/N 20527

P/N 1940

GENUINE

TROWELMADE IN USA

METRIC

PO

WER TROW

EL

P/N 1736

P/N 1848

P/N 2938


HPLA/HPHA-SERIES 46" TROWEL— SPECIFICATIONS (TROWEL)

NOTE:

1. Sound pressure is a weighted measure. Measured at theoperators ear position while the walk-behind trowel isoperating at full throttle on concrete in a manner most oftenexperienced in “normal” circumstances. Sound pressuremay vary depending upon the condition of the concrete.Hearing protection is always recommended.

Figure 2. HPLA/HPHA-SERIES 46" Trowel Dimensions

2. The vibration level indicated is the maximum RMS (RootMean Square) value obtained at the handle grip whileoperating the walk-behind trowel on curing concrete in amanner most often experienced in “normal” circumstances.Values were obtained from all three axes of motion. Thevalues shown represent the maximum RMS value fromthese measurements.

Side View

snoitacificepSleworT"64seireS-AHPH/ALPH.1elbaT)kooHgnitfiL(thgieH–A )mm2.678(ni5.43

)reveLtnemegagnEthgieH–B )mm2.440,1(ni1.14htdiW–C )mm4.861,1(0.64htgneL–D )mm1.019,1(2.57

gnitarepO–thgieW .gK501/.sbl032erusserPdnuoS bd79

noitarbiV s/m5.42(g5.2 2)retemaiDgniR )mc711(ni64

sedalBforebmuN 4ro3)s/m(MPF–deepSpiTedalB )s/m5.7(mpf874,1

)enilosaG(MPR–rotoR 521ot06)mc(.ni–htdiWhtaP )332(84


HPLA/HPHA-SERIES 46" TROWEL— SPECIFICATIONS (ENGINES)

)enignE(snoitacificepS.2elbaT

enignE

ledoM 2PAQ1K043XGADNOH

epyT

elgniS,ekorts4delooc-riA,VHO,rednilyC

enilosaGtfahSlatnoziroHenignE

ekortSXeroB.ni5.2X.ni2.3

)mm46xmm28(

tnemecalpsiD cc983.ni.uc7.32

tuptuOxaM .M.P.R0063/.P.H0.11

yticapaCknaTleuFsnollaG.S.U27.1.xorppA

)sretiL5.6(

leuF enilosaGelibomotuAdedaelnU

yticapaCliOebuL .tQSU61.1

dohteMlortnoCdeepS epyTthgiew-ylFlagufirtneC

dohteMgnitratS tratSlioceR

noisnemiD)HxWxL(

.ni4.71X7.71x0.51)mm344X054X083(

thgieWteNyrD ).gK13(sbl4.86


HPLA/HPHA-SERIES 46" TROWEL— GENERAL INFORMATIONHPLA/HPHA-SERIES 46" Walk-Behind TrowelFamiliarization

This walk-behind trowel is designed for the floating andfinishing of concrete slabs.

Take a walk around the trowel. Take notice of all the majorcomponents (see Figure 3, pages 16 and 17) like the engine,blades, quick pitch control, air cleaner, centrifugal stop switchetc. Check that there is always oil in the engine.

Read all the safety instructions carefully. Safety instructions willbe found throughout this manual and on the trowel. Keep allsafety information in good, readable condition. Operators shouldbe well trained on the operation and maintenance of the trowel.

Before using your trowel, test it on a flat watered down section offinished concrete that is free of any debris and other objects.

This trial test run will increase your confidence in using the troweland at the same time it will familiarize you with the trowel’scontrols. In addition you will understand how the trowel handlesunder actual conditions.

Engines

This trowel is available with an 11.0 HP HONDA gasoline engine.Refer to the engine owner’s manual for instructions regardingthe operation and maintenance of your engine. The enginemanual is included with your trowel at the time of shipment fromWhiteman. Please contact your nearest Multiquip Dealer for areplacement should the original manual disappear.

Drive System

Power is transferred from the engine to the gearbox input shaftvia a V-belt or pulley drive system. The pulley engages usingeither a centrifugal or manual clutch. See page 23.

Gearbox

The gearbox is located beneath the engine and transfers powerto the rotor or spider assembly. The gearbox controls therotational speed of the trowel and is equipped with two shafts(input and output).

Spider

The vertical output shaft of the gearbox connects to a cast hubcalled the spider. The spider has 4 arms that extend outwardthat are used for attachment of blades or other accessories.Remember as the gearbox output shaft rotates so does the spiderassembly.

NEVER attempt to lift the trowel by yourself.ALWAYS get the assistance of anotherperson to help lift the trowel or use a crane orlifting device to move the trowel.

Moving the HPLA/HPHA-SERIES 46" Walk-Behind Trowel

This walk-behind trowel is designed to be moved and handledin several ways. The easiest way to lift the trowel is to use theauxiliary lifting tube that is attached to the main handle. Seepage 24, Figure 20. When using the auxiliary tube, always usetwo persons to lift the trowel.

Some models have a lifting bail (option) installed. A strap orchain can be attached to the lifting bail, allowing a forklift orcrane to lift the trowel up onto a slab of concrete. Use a liftingdevice of adequate lifting capacity to lift the trowel.

Training

For proper training, please use the “TRAINING CHECKLIST”located in the front of this manual (Page 6). This checklist willprovide an outline for an experienced operator to provide trainingto a new operator.


Blades

The blades of the trowel finish the concrete as they are rotatedaround the surface. Blades are classified as combination (8inches wide), float (10 or 8 inches wide), and finish (6 incheswide). This trowel comes equipped with either three or fourblades per rotor equally spaced in a radial pattern andattached to vertical rotating shaft by means of a spiderassembly.

Centrifugal Stop Switch

In the event of a trowel runaway condition (operator releasesthe handle), a centrifugal stop switch or manual clutchdepending on which trowel you have, will stop the engineand bring the trowel to a halt.


HPLA/HPHA-SERIES 46" TROWEL— CONTROLS AND COMPONENTS

Figure 3. HPLA/HPHA-SERIES 46" Walk-Behind Trowels


(Figures 3) shows the location of the basic controls orcomponents, for the HPLA/HPHA-SERIES 46" trowel. Listedbelow is a brief explanation of each control or component

1. Quick Pitch™ Control Handle – To adjust the pitch ofthe blades, grasp the handle then squeeze and either movethe handle forward or backward to achieve the desiredblade pitch.

2. Handlebar Adjuster – Change the angle/height of thehandle bars by loosening star wheel, adjust handlebars todesired location, tighten starwheel firmly to hold handlebarsin that position.

3. Hand Grip/Handle Bar – When operating the trowel, placeboth hands on each grip to maneuver the trowel. Replacehand grips when they become worn or damaged.

4. Throttle Control Lever – Controls the speed of the engine.Pull the hand grip toward the operator to increase enginespeed (high), away from the operator to decrease enginespeed (low or idle).

5. Throttle (Engine) – Controls engine speed when throttlecontrol lever is pulled toward the operator.

6. V-Belt Cover – Remove this cover to gain access to the V-belt. NEVER operate the trowel with this cover removed.

7. Centrifugal Safety Stop Switch – In the event the operatorloses control of the trowel, this switch will shut-down theengine.

8. Auxiliary Lifting Tube - Use this tube to lift the trowel ontoa slab. Tube is to be inserted into socket located in front ofthe gearbox.

9. Stabilizer Ring – Reduces trowel arm vibration. Helpsstabilize trowel arm.

10. Trowel Lifting Point – Insert the auxiliary lifting tube here.See Figure 20.

11. Pitch Control (standard models) - Turn this "Star Wheel"clockwise for increase blade pitch, and counter-clockwisefor decrease blade pitch.

12. Blades – This trowel is equipped with combination blades.These blades are versatile and should take care of mosttroweling needs. In addition float discs can be attached tothe trowel arms that will allow the trowel to float on "wet"concrete.

13. Main Tube - When disassembling components inside thetube exercise extreme CAUTION! Tube is spring-loaded,severe injury could result if not disassembled correctly.

14. Guard Ring- NEVER! put hands or feet inside guard ring.

15. Engine – This trowel uses an 11HP Honda gasolineengine.

16. Trowel Arm – NEVER operate the trowel with a bent, brokenor out of adjustment trowel arm. If the blades show unevenwear patterns or some blades wear out faster than others,the trowel arm may need to be adjusted. Use the trowelarm adjustment tool P/N 1817 to adjust the trowel arms.

HPLA/HPHA-SERIES 46" TROWEL— CONTROLS AND COMPONENTS


Figure 4. Engine Controls and Components

INITIAL SERVICING

The engine (Figure 4) must be checked for proper lubrication andfilled with fuel prior to operation. Refer to the manufacturers enginemanual for instructions & details of operation and servicing.

1. Fuel Filler Cap – Remove this cap to add unleadedgasoline to the fuel tank. Make sure cap is tightenedsecurely. DO NOT over fill.

6. Choke Lever – Used in the starting of a cold engine, or incold weather conditions. The choke enriches the fuelmixture.

7. Air Cleaner – Prevents dirt and other debris from enteringthe fuel system. Remove wing-nut on top of air filtercannister to gain access to filter element.

8. Spark Plug – Provides spark to the ignition system. Setspark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Cleanspark plug once a week.

9. Muffler – Used to reduce noise and emissions.

Engine components can generate extreme heat.To prevent burns, DO NOT touch these areas

while the engine is running or immediately after operating. NEVERoperate the engine with the muffler removed.

10. Fuel Tank – Holds unleaded gasoline. For additionalinformation refer to engine owner's manual.

DANGER

WARNING

HPLA/HPHA-SERIES 46" TROWEL— BASIC ENGINE

Adding fuel to the tank should be done only whenthe engine is stopped and has had an opportunity to

cool down. In the event of a fuel spill, DO NOT attempt to start theengine until the fuel residue has been completely wiped up, and thearea surrounding the engine is dry.

2. Throttle Lever – Used to adjust engine RPM speed (leveradvanced forward SLOW, lever back toward operatorFAST).

3. Engine ON/OFF Switch – ON position permits enginestarting, OFF position stops engine operations.

4. Recoil Starter (pull rope) – Manual-starting method. Pullthe starter grip until resistance is felt, then pull briskly andsmoothly.

5. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stopthe flow of fuel.

Operating the engine without an airfilter, with a damaged air filter, or afilter in need of replacement willallow dirt to enter the engine, causingrapid engine wear.

NOTE


HPLA/HPHA-SERIES 46" TROWEL — ASSEMBLY AND INSTALLATION

Assembly and Installation

Before the trowel can be put into operation there are somecomponents that must be installed before the trowel can be used.This section provided general instructions on how to install thosecomponents. Instruction sheet P/N 20485 provides further detailsfor the handle assembly.

Handle Tube Installation (All Models)

1. Install the handle tube to the gearbox as shown in (Figure 5).The mounting hardware should be contained in the shippingcontainer.

Figure 5. Handle Tube Installation

CAUTIONCAUTIONCAUTIONCAUTIONCAUTIONThe Quick-Pitch™ handle is spring loaded,personal injury or damage could result fromimproper handling or installation. Be carefulwhen installing this component.

2. On Quick-Pitch™ models, pivot the T-handle back(full pitch) (Figure 6). This will relax the spring inside thehandle tube. On either model, spread the handle bar endsjust enough to engage the teeth on the handle tube. Attachthe hand wheel assembly, position handlebar to desiredlocation, and tighten hand wheel firmly.

Figure 6. Handlebar Installation

2. Feed the throttle cable through the cable housing.

3. Connect the throttle cable to the engine. (Figure 8). Thereshould be a piece of wire installed on the trowel to showwhere to route the throttle cable. When connecting the cablehousing, make sure that no more than 1/4" (6.4mm) of thecable housing protrudes past the housing clamp on theengine.

Figure 8. Throttle Cable Connection

CABLE HOUSING

ENGINETHROTTLE

LEVER

SWIVEL STOPSCREW

THROTTLECABLE END

CABLEHOUSING

CLAMP

Figure 7. Throttle

Throttle Cable Installation

1. Place the throttle lever (Figure 7) to the idle position.

Considerable force may berequired when moving the Quick-Pitch™ T-handle forward orbackward.

NOTE


Handle Height Adjustment

If handle height adjustment is desired, a handle wedge kit can bepurchased for your trowel by ordering P/N 2576 from your Multiquipdealer. These wedges are placed between the handle and thegearbox to adjust the operating height of the handle. This kitcomes complete with wedges, new bolts and installationinstructions. This will move your operating handle position up ordown approximately 3” (76mm).

HPLA/HPHA-SERIES 46" TROWEL — ASSEMBLY AND INSTALLATION

Safety Stop Switch Wire

Locate the safety stop switch wire protruding from the handletube (Figure10) and connect it to the tail wire on the engine.Test the safety stop switch to insure proper operation.

Figure 10. Engine Safety Stop Wire Connection

Figure 11. "No Pitch" Position (Standard)

Figure 12. "No Pitch" Position (Quick-Pitch™)

1. Expose the pitch cable to maximum by adjusting the handlepitch to the "no pitch" position. On the standard model turnthe pitch control counter-clockwise, (Figure 11). On theQuick-Pitch™ model, pivot the pitch handle forward or nopitch, (Figure 12).

7. These are general instructions. Installation of the throttlecable may vary for different engine configurations. Pleaselook for more detailed instructions inside the box containingthe handle. These more detailed instructions should provideadequate guidance for installing.

4. Tighten cable clamp screw and swivel stop screw.

5. After the cable has been installed on the engine, adjustand tighten operator position of the handle to lock thethrottle cable at the proper length.

6. Adjust cable tension loosening the lock nut on the throttlecable receiver (Figure 9), loosening or tightening theadjuster nut below it, then retightening the lock nut.

Pitch Cable Installation

Figure 9. Throttle Adjust


HPLA/HPHA-SERIES 46" TROWEL — ASSEMBLY AND INSTALLATIONPre-load Adjustment (Quick-Pitch™ Models Only)

1. After the Quick-Pitch™ handle has been installed on thetrowel, spring pre-load adjustment will be required.

2. Locate the adjustment screw on the underside of the handletube (Figure 15).

Figure 15. Pre-load Adjustment

Figure 14. Cable Yoke Attachment

3. A decal has been placed on the side of the handle tube toassist the user in the adjustment of the spring.

4. Align the arrow on the adjustment screw with the letter "B"COMBO on the decal.

5. Test the pitch control operation and adjust if necessary.

5. Insert the cable end through the yoke eyelet (Figure 14)Tighten the first brass set nut by hand to remove all theslack from the cable.

6 Using a wrench, tighten the second brass set nut up againstthe yoke boss. This will lock the cable in place.

7. Use a wrench and finish tightening the first brass set nut upagainst the yoke boss.

2. Lock the spring in the compressed position, by releasingthe blade pitch adjustment trigger, (Quick-Pitch™ model).

3. Remove one brass set nut from the blade pitch cable endas shown in (Figure 13).

4. Thread the second brass set nut towards the cable as faras possible.

Figure 13. Blade Pitch Cable

YOKE

THREAD CABLE ENDTHROUGH YOKE EYELET

TIGHTEN SECONDBRASS SET NUTAGAINST YOKE BOSS

USE A WRENCH TOTIGHTEN FIRST BRASSSET NUT AGAINST YOKE BOSS


CAUTIONCAUTIONCAUTIONCAUTIONCAUTIONNEVER operate the trowelin a confined area orenclosed area structure thatdoes not provide ample freeflow of air.

ALWAYS wear approved eye and hearingprotection before operating the trowel.

NEVER place hands or feet inside the guardrings while the engine is running. ALWAYS shutthe engine down before performing any kind ofmaintenance service on the trowel.

HPLA/HPHA-SERIES 46" TROWEL— PRE-INSPECTION

It is recommended that the trowel's safety stop switch be usedto stop the engine after every use. Doing this will verify that theswitch is working properly and presents no danger to the operator.

Before Starting

1. Read safety instructions at the beginning of manual.

2. Clean the trowel, removing dirt and dust, particularly theengine cooling air inlet, carburetor and air cleaner.

3. Check the air filter for dirt and dust. If air filter is dirty, replaceair filter with a new one as required.

4. Check carburetor for external dirt and dust. Clean with drycompressed air.

5. Check fastening nuts and bolts for tightness.

Engine Oil Check

1. To check the engine oil level, place the trowel on secure levelground with the engine stopped.

2. Remove the filler dipstick from the engine oil filler hole(Figure 16) and wipe it clean.

Figure 16. Engine Oil Dipstick (Removal)

3. Insert and remove the dipstick without screwing it into the fillerneck. Check the oil level shown on the dipstick.

4. If the oil level is low (Figure 17), fill to the edge of the oil fillerhole with the recommended oil type (Table 3). Maximum oilcapacity is 1.16 US Qt. (1.1 liters).

Figure 17. Engine Oil Dipstick (Oil Level)

Reference manufacturer enginemanual for specific servicinginstructions. NOTE

epyTliO.3elbaT

nosaeS erutarepmeT epyTliO

remmuS rehgiHroC°52 03-W01EAS

llaF/gnirpS C°01~C°52 02/03-W01EAS

retniW rewoLroC°0 01-W01EAS


HPLA/HPHA-SERIES 46" TROWEL— PRE-INSPECTION

Motor fuels are highly flammable and can bedangerous if mishandled. DO NOT smokewhile refueling. DO NOT attempt to refuel thetrowel if the engine is hot! or running.

Blade Check

Check for worn or damaged blades. Check to see if one blade isworn out while the others look new. If this is the case there couldbe a blade pitch problem. Refer to the maintenance section ofthis manual for blade pitch adjustment procedure. Replace anyworn blades.

CONTROLS

Safety Stop Switch

This trowel has been equipped with a centrifugal safety stopswitch. (Figure 19)

Gearbox Oil

1. Determine if the gearbox oil is low by removing the oilplug located on the side of the gearbox. This plug will bemarked by the "check" decal. See (Figure 18). The correctlevel of the lubrication oil should be to the bottom of the fillplug.

Figure 18. Gearbox

2. If lubrication oil begins to seep out as the drain plug isbeing removed, then it can be assumed that the gearboxhas a sufficient amount of oil.

3. If lubrication oil does not seep out as the drain plug isbeing removed, fill with type ISO 680 (Whiteman P/N 10139)gearbox lubricant oil until the oil filler hole overflows.

Figure 19. Centrifugal Safety Stop Switch

GEARBOX

DRAINPLUG

OIL SIGHT/FILL PLUG

NEVER! disable or disconnect thesafety stop switch. It is provided foroperator safety. Injury may result if itis disable, disconnected orimproperly maintained.

NOTE

The switching mechanism of this switch should operate freelyand should always be kept in this condition. With the switch inthe OFF position, the engine should not start or run. The purposeof this switch is to stop the engine in a runaway situation, (i.e. theoperator releasing the handle during operation). Safety stopswitches should be tested every time the engine is started. Seepage 25 for procedures to check the operation of the Safety StopSwitch.

1. Remove the gasoline cap located on top of fuel tank.

2. Visually inspect to see if fuel level is low. If fuel is low, replenishwith unleaded fuel.

3. When refueling, be sure to use a strainer for filtration. DONOT top-off fuel. Wipe up any spilled fuel.

V-belt Check

A worn or damaged V-belt can adversely affect the performanceof the trowel. If a V-belt is defective or worn simply replace the V-belt as outlined in the maintenance section of this manual.

Explosive Fuel

DANGERDANGERDANGERDANGERDANGER

Fuel Check


HPLA/HPHA-SERIES 46" TROWEL — INITIAL START-UP

This section is intended to assist the operator with the initialstart-up of the walk-behind trowel. It is extremely important thatthis section be read carefully before attempting to use the trowelin the field.

DO NOT use your trowel until this section is thoroughlyunderstood.


Starting the Engine

1. Place the engine fuel valve lever (Figure 21) to the "ON"position.

DO NOT attempt to operate the trowel untilthe Safety, General Information andInspection sections of this manual havebeen read and thoroughly understood.Depending on engine manufacturer,operating steps may vary. See enginemanufactures operating manual. Thefollowing start-up procedure makesreference to a HONDA 11 HP Engine(Manual Start).

2. Move the throttle lever (Figure 22) to the "idle" position.

Figure 21. Engine Fuel Valve Lever

Figure 22. Throttle (Idle Position)

Lifting the Trowel Onto a Slab.

Auxiliary Lifting Tube

Remove the auxiliary lifting tube located on top of the main handle.Insert the tube into the socket located on the opposite side of thegearbox (Figure 20) from the handle.

Make sure that the hole in the tube engages with the pin in thesocket. With one person lifting from the main handle, and anotherlifting from the auxiliary lifting tube pick up the machine to moveonto a slab.

Figure 20. Lifting the Trowel

Lifting Bail (Option)

The lift bail is optional on new trowels. It provides an optimal liftpoint for moving the trowel. Lift bales or forklift can be used tolift a trowel up onto a building with a crane. See “OptionalEquipment” section in this manual for ordering information.

Using a crane to move a machine with a lift bail is highlyrecommended, and is perfectly safe for the machine. Extra careshould be taken when lifting the machine off the ground, though.Serious damage to the machine or personal injury could becaused by dropping a trowel.

CAUTIONCAUTIONCAUTIONCAUTIONCAUTIONThe trowel is heavy and awkward to movearound. Use proper heavy lifting proceduresand DO NOT lift the trowel by the guardrings.

CAUTIONCAUTIONCAUTIONCAUTIONCAUTIONThe trowel must be stabilized by the personcarrying the operator’s handle (Figure 20). Ifit is not stabilized properly the handle mayswing around and flip the trowel, thus causingdamage to the trowel and bodily injury.


3. Place the centrifugal safety stop switch (Figure 23) in the"ON" position.

Figure 23. Centrifugal Safety Stop Switch

4. Place the Choke Lever (Figure 24) in the "CLOSED "position

Figure 24. Engine Choke Lever

5. Grasp the starter grip (Figure 25) and slowly pull it out. Theresistance becomes the hardest at a certain position, corre-sponding to the compression point. Pull the starter grip brisklyand smoothly for starting.

Figure 25. Starter Grip

6. If the engine has started, slowly return the choke lever(Figure 24) to the OPEN position. If the engine has not startedrepeat steps 1 through 5.

7. Before the trowel is placed into operation, run the engine forseveral minutes. Check for fuel leaks, and noises that wouldassociate with a loose guard ring and/or covers.

8. Test the Safety Stop Switch.

a. With the engine at idle, move the safety stop switch leverto "OFF" (Figure 23). The engine should shut off.

b. CLEAR THE AREA AROUND THE TROWEL. Movethe safety stop switch lever back to the "ON" position,restart the engine and let idle. Stand behind the handleand spin the handle to the right, simulating a runawaysituation. (See Figure 26). Centrifugal force shouldthrow the safety switch outward to the "OFF" positionthus shutting off the engine

Figure 27. Throttle (Run Position)

HPLA/HPHA-SERIES 46" TROWEL — INITIAL START-UP

9. To begin troweling, pull the throttle lever (Figure 27) towardthe "RUN" position.

Figure 26. Testing the Centrifugal Safety Stop Switch.


HPLA/HPHA-SERIES 46" TROWEL — OPERATION

PITCHING THE BLADES

Quick Pitch Handle

1. To pitch the blades upwards using the "Quick-Pitch™"T-handle, (Figure 28) simply squeeze the trigger lockand pull the T-handle towards the operator. Pushingthe T-handle towards the engine will cause the bladesto lay flat.

Standard Handle

1. To pitch the blades upwards using the "Standard" handle,(Figure 29) simply turn the star-wheel clockwise. Turning thestar wheel counter clockwise will cause the blades to lay flat.

Figure 28. Quick-Pitch™ T- Handle

Figure 29. Standard Handle

Maneuvering the Trowel

1. Get into the operator’s position behind the handle. With asecure foothold and a firm grasp on the handles slowlyincrease the engine speed until the desired blade speed isobtained.

2. To maneuver the trowel, gently lift up on or press down on themain trowel handle. To move the machine to the operator’sleft, lift up on the handle, to move machine to the right, pushdown on the handle.

3. The best method for finishing concrete is to slowly walkbackwards (Figure 30) with the trowel, guiding the trowelfrom side to side. This will cover all footprints on wet concrete.

4. Remember that if you let go of the trowel, just step away andlet the trowel come to a complete stop before trying to recoverthe trowel. See (Figure 26) to see the area around the trowelto keep clear of.

The following steps are intended as a basic guide to machineoperation, and are not to be considered a complete guide toconcrete finishing. We suggest that all operators (experiencedand novice) read “Slabs on Grade” published by the AmericanConcrete Institute, Detroit, Michigan. Read the “Training”section of this manual for more information.


HPLA/HPHA-SERIES 46" TROWEL — OPERATION

Figure 30. Maneuvering The Trowel

(Figure 30) below illustrates a typical walk-behind trowelapplication. Practice maneuvering the trowel. The trick is to letthe trowel do the work.

Continue to practice maneuvering the trowel. Try to practice as ifyou were finishing a slab of concrete. Practice edging andcovering a large area. Remember a good finishing technique isto work backwards. Be careful when moving backwards so thathazards can be avoided. The best way to get accustomed to thetrowel is repeated use.

WARNINGWARNINGWARNINGWARNINGWARNING WARNINGWARNINGWARNINGWARNINGWARNINGNEVER place your feet or hands inside the guardrings while starting or operating this equipment.

ALWAYS keep clear of rotating or moving partswhile operating this equipment.


Blades

Blades are a vital part of finishing concrete. This trowel, orfinisher, has been designed to finish concrete and the blades arebuilt to stringent quality standards out of the finest trowel steel. Ifyou need replacement blades, consult your parts list in thismanual for part numbers and order them from your Multiquip partsdealer or importer.

Combo Blades

This trowel was equipped with combination float/finish (Figure31) blades as original equipment. These blades have beendesigned for optimum performance in both the floating andfinishing operations. These blades are versatile and should takecare of most troweling needs.

HPLA/HPHA-SERIES 46" TROWEL — OPTIONS

Float Discs (Optional)

These round discs (Figure 34) attach to the spiders and allow themachine to “float” on “wet” concrete. The disc design allows earlyfloating and easy movement from wet to dry areas. They are alsovery effective in embedding large aggregates and surfacehardeners.

Clip-On Float Blades (Optional)

These blades will clip (Figure 33) on to an existing installed blade,allowing your finisher to float on “wet” concrete so that thetroweling operation can begin as early as possible. They areeasily removable, so that after the floating operation, when theconcrete is sufficiently cured, they can be removed to expose thefinish blades for continued troweling.

Figure 32. Finish Blade

Figure 33. Clip-On Float Blade

Figure 34. Float Disk

Finish Blades (Optional)

These blades (Figure 32) have been specifically designed forfinish operations with this trowel. They will provide a premiumsurface finishing capability from your trowel. They should only beused after the concrete has set to the point where the trowel doesnot sink into the concrete when placed on it.

Figure 31. Combination Blade

Blades should be changed whenthey fail to finish concrete in asatisfactory manner.

NOTE


Trowel Arm Adjustment Tool

If blades show uneven wear patterns or some tend to wear outfaster than others, the trowel arms may need to be adjusted.Whiteman makes a special tool (Figure 37) that will adjust all ofthe trowel arms consistently. The Trowel Arm Fixture P/N is 1817.

Grinding Attachments

Available grinding attachments are used for grinding surfaceimperfections or joints. These attachments allow greater utilizationof your trowel. (Figure 35) illustrates a typical grinding diskassembly, complete with hub and stone mounting plate.

Figure 37. Trowel Arm Adjustment Fixture

HPLA/HPHA-SERIES 46" TROWEL — OPTIONS

Lifting Bail

There is a heavy duty, center balance type lifting bail (Figure 36)made specifically for your trowel. These bales are ideal for liftingand transporting your trowel. They are designed to lift the finisherand balance it on it’s center of gravity, providing great stabilitywhile lifting. This option is not available on electric trowel models.

Figure 36. Lifting Bail

Figure 35. Grinding Disk


HPLA/HPHA-SERIES 46" TROWEL — MAINTENANCE (ENGINE)

QP40TH — MAINTENANCE (ENGINE)

Reference manufacturer enginemanual for specific servicinginstructions.

NOTE

Engine Maintenance

Perform engine maintenance procedures as referenced byTable 4 below:

eludehcSecnanetniaMenignE.4elbaT

)3(NOITPIRCSED NOITAREPO EROFEB

TSRIFHTNOM

RO.SRH01

YREVESHTNOM3

RO.SRH52

YREVESHTNOM6

RO.SRH05

YREVERAEY

RO.SRH001

YREVESRAEY2

RO.SRH002

liOenignEKCEHC X

EGNAHC X

renaelCriAKCEHC X

EGNAHC )1(X

stloB&stuNllAfInethgit-eR

yrasseceNX

gulPkrapSNAELC-KCEHC X

ECALPER X

sniFgnilooC KCEHC X

retserrAkrapS NAELC X

knaTleuF NAELC X

retliFleuF KCEHC X

deepSeldI TSUJDA-KCEHC )2(X

ecnaraelCevlaV TSUJDA-KCEHC )2(X

senilleuF KCEHC )2()yrassecenfiecalper(sraey2yrevE

nidesunehwyltneuqerferomecivreS)1( YTSUD .saera

yllacinahcemeradnaslootreporpehtevahuoysselnu,relaedcivresruoyybdecivresebdluohssmetiesehT)2(serudecorpecivresroflaunaMpohsADNOHehtotrefeR.tneiciforp

.slavretniecnanetniamreporpenimretedotnoitarepofosruohgol,esulaicremmocroF)3(


HPLA/HPHA-SERIES 46" TROWEL — MAINTENANCE (ENGINE)Maintenance

Perform the engine maintenance procedures as indicated below:

DAILY■ Thoroughly remove dirt and oil from the engine and control

area. Clean or replace the air cleaner elements as necessary.Check and retighten all fasteners as necessary. Check thespring box and bellows for oil leaks. Repair or replace asneeded.

WEEKLY

■ Remove the fuel filter cap and clean the inside of the fueltank.

■ Remove or clean the filter at the bottom of the tank.

■ Remove and clean the spark plug (Figure 38), then adjustthe spark gap to 0.028 ~0.031 inch (0.6~0.7 mm). This unithas electronic ignition, which requires no adjustments.

Figure 40. Engine Air Cleaner

DO NOT use gasoline as a cleaning solvent,because that would create a risk of fire orexplosion.

DANGER :

ENGINE AIR CLEANER

1. Remove the air cleaner cover and foam filter element asshown in Figure 40.

2. Tap the paper filter element (Figure 40) several times on ahard surface to remove dirt, or blow compressed air [notexceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filterelement from the air cleaner case side. NEVER brush off dirt.Brushing will force dirt into the fibers. Replace the paper filterelement if it is excessively dirty.

3. Clean foam element in warm, soapy water or nonflammablesolvent. Rinse and dry thoroughly. Dip the element in cleanengine oil and completely squeeze out the excess oil from theelement before installing.

ENGINE OIL

1. Drain the engine oil when the oil is warm as shown inFigure 39.

2. Remove the oil drain bolt and sealing washer and allowthe oil to drain into a suitable container.

3. Replace engine oil with recommended type oil as listedin Table 3. Engine oil capacity is 1.16 quarts (1.1 liters).DO NOT overfill.

4. Install drain bolt with sealing washer and tighten se-curely.

Figure 39. Engine Oil (Draining)

Figure 38. Spark Plug Gap


Figure 41. Worn Spider Plate

Trowel Arm Adjustment Procedure

A level, clean area to test the trowel prior to and after is essential.Any unlevel spots in the floor or debris under the trowel bladeswill give an incorrect perception of adjustment. Ideally, a 5 x 5"three-quarter inch thick flat steel plate should be used for testing.

1. To determine which blades need adjustment, place thetrowel in the test area (three-quarter inch thick plate) and lookfor the following conditions:

■ Pitch the blades as flat as possible and look at theadjustment bolts. They should all barely make contactwith the lower wear plate on the spider. If you can seethat one of them is not making contact, some adjustmentwill be necessary.

■ Is the machine wearing out blades unevenly (i.e. oneblade is completely worn out while the others look new)?

(Figure 41) below illustrates a "worn spider bushings or benttrowel arms". Check to see that adjustment bolt is barelytouching (0.10" max. clearance) lower wear plate. All alignmentbolts should be spaced the same distance from the lower wearplate.

(Figure 42) below illustrates the "correct alignment " for a spiderplate (as shipped from the factory).

Figure 42. Correct Spider Plate Alignment

At the front of the book (Page 7) there is a “Daily Pre-OperationChecklist ”. Make copies of this checklist and use it on a dailybasis.

MAINTENANCE SCHEDULE

Daily (8-10 Hours)

1. Check the oil level in the engine crankcase and gear box,fill as necessary.

2. Check V-belt.

Weekly (50-60 Hours)

1. Relube arms, thrust collar and clutch.

2. Replace blades if necessary.

3. Check and clean or replace the engine air filter asnecessary.

4. Replace engine oil and filter as necessary, see enginemanual.

Monthly (200-300 Hours)

1. Remove, clean, reinstall and relube the arms and thrustcollar. Adjust the blade arms.

2. Remove, clean, reinstall clutch.

Yearly (2000-2500 Hours)

1. Check and replace if necessary the arm bushings, thrustcollar bushings and shaft seals.

2. Check pitch control cables for wear.

3. Adjust blade speed.

HPLA/HPHA-SERIES 46" TROWEL — MAINTENANCE (TROWEL)

NOTE

NOTE

See the engine manual supplied withyour machine for appropriate enginemaintenance schedule andtroubleshooting guide for problems.

The following procedure should befollowed to adjust trowel arms whenit becomes apparent that the trowelis finishing poorly or in need ofroutine maintenance.

ALWAYS allow the engine tocool before servicing. NEVERattempt any maintenancework on a hot! engine.

CAUTION!CAUTION!CAUTION!CAUTION!CAUTION!



■ Does the trowel have a perceived rolling or bouncingmotion when in use?

■ Look at the trowel while it is running, does the guardring “rock up and down” relative to the ground?

2. Start engine, and bring trowel blades up to full speed and lookfor the following conditions:

a. Locate the cone point square head set screw (Figure 43)and attached jam nut found on the side of the spiderassembly.

Spider Removal

1. Once it is determined that an adjustment is required, removethe spider assembly from the gearbox shaft as follows:

Figure 43. Spider/Gearbox Removal

b. Loosen the jam nut and cone point square head setscrew, and carefully lift the upper trowel assembly offof the spider assembly. A slight tap with a rubber malletmay be necessary to dislodge the spider from the mainshaft of the gearbox.

c. If the trowel is equipped with an outer stabilizer ring(Figure 44), remove the four bolts at the end of eachspider arm.

Figure 44. Stabilizer Ring

d. Examine stabilizer ring for out of round or bends. If ringis damaged, replace ring. If ring is found to be correct withno damage, set aside.

Trowel Arm Removal

1. Each trowel arm is held in place at the spider plate by a hexhead bolt (zerk grease fitting) and a roll pin. Remove both thehex head bolt and the roll pin (Figure 45) from the spiderplate.

2. Remove the trowel arm from the spider plate.

Figure 45. Removing Roll Pinand Zerk Grease Fitting


Trowel Arm Flatness Test

1. Using a piece of 3/4 inch thick steel plate or any surface whichis true and flat, check all six sides of each trowel arm forflatness.

2. Check each of the six sides of the trowel arm (hex sectiononly) using a ten thousands of an inch (max.) feeler gauge(Figure 48) between the flat of the trowel arm and an ex-tremely flat test surface.

3. If the trowel arm is found to be uneven or bent, replace thetrowel arm. A bent trowel will not allow the trowel to operatein a smooth fluid rotation.

4. Next, check each of the six sides of the round machined shaftsection of the trowel arm. Each section should have the sameclearance between the round of the trowel arm shaft and thetest surface.

Figure 48. Trowel Arm Flatness Test

HPLA/HPHA-SERIES 46" TROWEL — MAINTENANCE (TROWEL)3. Should the trowel arm inserts (bronze bushing ) come out

with the trowel arm, remove the bushing from the trowel armand set aside in a safe place. If the bushing is retained insidethe spider plate, carefully remove the bushing.

4. Examine the bronze trowel arm bushing insert (Figure 46),clean if necessary. Replace bushing if out of round or worn.

Figure 46. Bronze Bushings

Trowel Blade Removal

1. Remove the trowel blades from the trowel arm by removingthe three hex head bolts (Figure 47) from the trowel arm. Setblades aside.

Figure 47. Trowel Blades

2. Wire brush any build-up of concrete from all six sides of thetrowel arm. Repeat this for the remaining three arms.

NOTE

Trowel arms can be damaged byrough handling or by strikingexposed plumbing or forms while inoperation. ALWAYS look-out forobjects which might cause damageto the trowel arms.


Trowel Arm Adjustment

Shown in (Figure 49) is the adjustment fixture with a trowel arminserted. As each trowel arm is locked into the fixture, the arm boltis adjusted to where it contacts a stop on the fixture. This willconsistently adjust all of the trowel arms, keeping the finisher asflat and evenly pitched as possible.

1. Locate the trowel arm adjustment tool P/N 1817. Set theadjustment tool for a clock-wise blade rotation, meaning thefixture arm is in the "UP" position.

Figure 49. Trowel Arm Adjustment Tool


2. Trowels manufactured prior to June of 1982 require that thedistance from the end of the adjusting bolt and the fixture armmust be 7/8" (Figure 49). Conversely, trowels manufacturedafter June of 1982 require that the distance from the end ofthe adjusting bolt and the fixture arm must be 1/2".

3. Un-screw the locking bolts on the adjustment tool, and placethe trowel arm into the adjustment fixture channel as shownin (Figure 49). A thin shim may be required to cover theblade holes on the trowel arm. Make sure to align the troweladjustment bolt with the fixture adjustment bolt.

4. Using an allen wrench, tighten the locking bolts on theadjustment tool and securely lock the trowel arm in place.

5. Loosen the locking nut on the trowel arm lever, then turn thetrowel arm adjusting bolt until it barely touches (.010") theadjusting bolt on the fixture.

6. After the correct adjustment has been made, tighten lock nuton trowel arm lever to lock in place.

7. Loosen locking bolts on adjustment fixture, and removetrowel arm from fixture.

8. Repeat steps 2-7 for the remaining trowel arms.

Re-Assembly

1. Clean and examine the upper/lower wear plates and thrustcollar. Examine the entire spider assembly. Wire brush anyconcrete or rust build-up. If any of the spider components arefound to be damaged or out of round, replace them.

2. Make sure that the bronze trowel arm bushing is not damageor out of round. Clean the bushing if necessary. If the bronzebushing is damage or worn, replace it.

3. Reinstall bronze bushing onto trowel arm.

4. Repeat steps 2 -3 for each trowel arm.

5. Make sure that the spring tensioner is in the correct positionto exert tension on the trowel arm.

6. Insert all trowel arms with levers into spider plate (with bronzebushing already installed) using care to align grease hole onbronze bushing with grease hole fitting on spider plate.

7. Lock trowel arms in place by tightening the hex head zerkgrease fitting and jam nut.

8. Re-install the blades back onto the trowel arms.

9. Install stabilizer ring onto spider assembly.

10. Reinstall lower wear plate, thrust collar and upper wearring in the reverse order that they were dis-assembled ontothe spider shaft. Make sure that there is little or no lateralmovement between the thrust collar and the spider shaft.


11. Carefully lift the upper trowel assembly, line up the key-way on gear box main shaft and insert into spider assembly.

12. Reinstall square head cone point into spider plate andtighten in place. Tighten jam nut. Use care in making surepoint of set screw engages groove in gear box main shaft.

13. Lubricate all grease points (zerk fittings) with premium"Lithum 12" based grease, conforming to NLG1 Grade #2consistency.

Testing

1. Place trowel in test area, start engine and test trowel forsmoothness.

2. If trowel bounces has excessive vibration or does not runsmoothly repeat alignment procedure.

Changing a Blade

Whiteman recommends that all the blades be changed at thesame time. The machine may wobble or bounce if only some ofthe blades are changed at one time.

1. Place the machine on a flat, level surface. Adjust the bladepitch control to make the blades as flat as possible. Note theblade orientation on the trowel arm.

2. Remove the three bolts and lock washers that secure theblade to the trowel arm. Remove the blade.

3. Using a wire brush, scrape all concrete particles and foreigndebris from the trowel arm.

4. Install the new trowel blade onto the trowel arm. Make sureblade is installed correctly, maintaining the proper orienta-tion for direction of rotation.

5. Reinstall the three bolts and lock washers that secure theblade to the trowel arm. Tighten all three bolts securely.

6. Repeat steps 1- 5 for all remaining blades.


NOTEBefore removing the blades,please note the orientation of theblade on the trowel arm.

V-Belt Removal and Replacement

1. Remove the two T-Bolts and lockwashers hold on the beltguard.

2. Remove the belt guard.

3. Work the belt up and over the bottom pulley and remove thebelt.

4. Replace with the appropriate belt:

HPLA46411H: p/n 0261, A31 Gates HPII

HPHA46411H: p/n 152 3, A28 Gates HPII

5. Place the belt in the upper pulley groove then work the beltover the bottom pulley into place.

NOTE

The V-Belt will tension itselfautomatcally during operation.NO FURTHER ADJUSTMENTOR TENSIONING IS NECES-SARY.

6. Replace the belt guard, lockwashers, and secure with the T-Bolts.

NEVER operate equipment withcovers, or guards removed.Keep fingers, hands, hair andclothing away from all movingparts to prevent injury.

WARNING!WARNING!WARNING!WARNING!WARNING!


HPLA/HPHA-SERIES 46" TROWEL — TROUBLESHOOTING (TROWEL)

GNITOOHSELBUORTLEWORT.5ELBAT

MOTPMYS MELBORPELBISSOP NOITULOS

tatonrohguorgninnurenignE.lla

?noitcnuflamhctiwsytefaS fihctiwsecalperroNOsihctiwsytefasehttahterusekaM.yrassecen

?leuF otdeilppusgniebleufsierehterusekaM.metsysleufehttakooL.deggolctonsiretlifleufehttahterusneotkcehC.enigneeht

?noitingI sidnarewopsahhctiwsnoitingiehttahterusneotkcehC.yltcerrocgninoitcnuf

.gninoitcnuftonhctiwsytefaS

?stcatnocdaB.

.hctiwsecalpeR

?snoitcennoceriwesooL .yrassecensaecalpeR.gniriwkcehC

?smelborprehtO .launams’rerutcafunamenignetlusnoC

sllor,secnuob“lewortfInevenusekamro,etercnoc

.”etercnocnislriws

?sedalB

.nrowylevissecxeton,noitidnocdoognierasedalbniatrecekaMehtmorf)mm05("2nahtsselonerusaemdluohssedalbhsiniFonerusaemdluohssedalbobmoc,egdegniliartehtotrabedalb

thgiartsebdluohsedalbfoegdegniliarT.)mm98("5.3tahtssel.rabedalbehtotlellarapdna

?redipSsaelgnahctipemasehttateserasedalbllatahtkcehC

rofelbaliavasiloottnemtsujdadleifA.redipsehttaderusaem.)tnempiuqElanoitpOees(smralewortehtfotnemtsujdathgieh

?smraleworttneB ehtfoenofI.smraleworttnebrofylbmessaredipsehtkcehC.yletaidemmitiecalper,tnebylthgilsnevesismra

?sgnihsubmraleworT

ybenodebnacsihT.ssenthgitrofsgnihsubmralewortehtkcehC"8/1nahteromsierehtfI.nwoddnapusmralewortehtgnivom

ebdluohssgnihsubeht,mraehtfopitehttalevartfo)mm2.3(.emitemasehttadecalperebdluohssgnihsubllA.decalper

?ralloctsurhT .redipsehtnotignitatorybralloctsurhtehtfossentalfehtkcehC.ralloctsurhtehtecalper)mm5.0("20.0nahteromybseiravtifI

?gnihsubralloctsurhTtlitnactifI.redipsehtnotignikcorybralloctsurhtehtkcehC

,].D.Oralloctsurhtehttaderusaemsa[)mm4.2("23/3nahterom.ralloctsurhtehtnignihsubehtecalper

?nrowgniraebtsurhT :etoN.eerfgninnipssititahteesotgniraebtsurhtehtkcehC.yrassecenfiecalper,pactsurhT

elbitpecrepasahenihcaM.gninnurelihwnoitomgnillor

?tfahsniaM

ebdluohsylbmessaxobraegehtfotfahstuptuoniamehTdnathgiartsnurtsumtfahsniamehT.ssenthgiartsrofdekcehc

redipsehttadnuorfotuo)mm80.0("300.0nahteromebtonnac.tnioptnemhcatta

?ekoY noylnevesserpekoyehtfosregnifhtobtahterusekamotkcehC.yrassecensaekoyecalpeR.pacraeweht

?hctiPedalBemasehtevahotdetsujdasiedalbhcaetahterusneotkcehC

ninoitcesecnanetniamreptsujdA.sedalbrehtollasahctip.launam


HPLA/HPHA-SERIES 46" TROWEL — TROUBLESHOOTING (TROWEL)

)DEUNITNOC(GNITOOHSELBUORTLEWORT.5ELBAT


hsiggulsrognippilshctulCdeepsenigneotesnopser

.egnahc

?stleb-VnroW .tleb-VecalpeR

?hctulclagufirtnecytriD .hctulcnaelcdnaelbmessasiD

tuonrowroevitcefeD?hctulclagufirtnec .hctulceritneecalpeR

?xobraegnisgniraebnroW kcehc,ytluciffidhtiwsetatortfahsfI.dnahybtfahstupnietatoR.yrassecensaecalpeR.sgniraebtfahstuptuodnatupnieht

nisraegnekorbronroW?xobraeg

sitfahstupniehtnehwsetatortfahsxobraegehttahtyfireV.tesasaraegmrowdnamrowehthtobecalpeR.detator

GNITOOHSELBUORTENIGNE.6ELBAT


yrotcafsitastonnoitarepO

.setautculfdeepslanoitatoR

?reporpmitnemtsujdaronrevoG .reveltcerrocotronrevogtsujdA

?evitcefedgnirpsronrevoG .noitingiecalperronaelC

?citarrewolfleuF .enilleufkcehC

noitcushguorhtninekatriA?enil

.enilnoitcuskcehC

gnikrowtonretratslioceR.ylreporp

?trapgnitatornitsuD .ylbmessaretratsliocernaelC

?eruliafgnirpsgnirpS .gnirpslairpsecalpeR


HPLA/HPHA-SERIES 46" TROWEL — TROUBLESHOOTING (ENGINE)

)DEUNITNOC(GNITOOHSELBUORTENIGNE.6ELBAT


tratsottluciffiD

gulpkrapstubelbaliavasileuFelbaliavarewoP(.etingitonlliw

.)elbacnoisnethgihta

?egdirbgniebgulpnoitingI .metsysnoitingikcehC

?noitingitatisopednobraC .noitingiecalperronaelC

evitcefedoteudtiucrictrohS?srotalusni

.srotalusniecalpeR

?pagkrapsreporpmI .pagtcerrocehtotpaggulpkrapsteS

gulpkrapstubelbaliavasileuFrewoP(.etingitonlliw TON

.)elbacnoisnethgihtaelbaliava

?hctiwspotstatiucrictrohS .evitcefedfihctiwspotsecalpeR.tiucrichctiwspotskcehC

?evitcefedliocnoitingI .liocnoitingiecalpeR

gulpkrapsdnaelbaliavasileuFnoisserpmoc(setingi )lamron .

nobrachtiwdeggolcrelffuM?stisoped

.relffumecalperronaelC

,retaw(etauqedaniesunileuF?)tsud

.leufhserfhtiwecalperdnametysleufhsulF

?deggolcrenaelCriA .renaelcriaecalperronaelC

gulpkrapsdnaelbaliavasileuFnoisserpmoc(setingi wol .)

?teksagdaehrednilycevitcefeD .teksagdaehecalperrostlobdaehrednilycnethgiT

?nrowrednilyC .rednilycecalpeR

?esoolgulpkrapS .gulpkrapsnehgiT

yrotcafsitastonnoitarepO

elbaliavarewophguonetoN-ssimon,lamronnoisserpmoc(

.)gnirif

?deggolcrenaelcriA

?enilleufniriA .enilleufmorf)riaevomer(deelB

taolfrotaerubracnilevelleuF?reporpmirebmahc taolfrotaerubractsujdA

?rednilycnistisopednobraC rednilycecalperronaelC

elbaliavarewophguonetoN-ssim,lamronnoisserpmoc(

.)gnirif

?evitcefedliocnoitingI .leufhserfhtiwecalperdnametysleufhsulF

?strohsnetfogulpnoitingI .noitinginaelc,seriwnoitingiecalpeR

,retaw(etauqedaniesunileuF?)tsud

.leufhserfhtiwecalperdnametysleufhsulF

.staehrevoenignE

ninoitsopednobracevissecxE?rebmahcnoitsubmoc

.esacknarcecalperronaelC

htiwdeggolcrelffumrotsuahxE.nobrac

.relffumecalperronaelC

?tcerrocnieulavtaehgulpkrapS .gulpkrapsepyttcerrochtiwgulpkrapsecalpeR


HPLA/HPHA-SERIES 46" TROWEL — EXPLANATION OF CODES

The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions.

SAMPLE PARTS LIST

NO. PART NO. PART NAME QTY. REMARKS1 12345 BOLT ......................1 .....INCLUDES ITEMS W/%2% WASHER, 1/4 IN. ...........NOT SOLD SEPARATELY2% 12347 WASHER, 3/8 IN. ...1 .....MQ-45T ONLY3 12348 HOSE ..................A/R ...MAKE LOCALLY4 12349 BEARING ..............1 .....S/N 2345B AND ABOVE

NO. Column

Unique Symbols — All items with same unique symbol

(@, #, +, %, or >) in the number column belong to the same assembly or kit, which is indicated by a note in the “Remarks” column.

Duplicate Item Numbers — Duplicate numbers indicate multiple part numbers, which are in effect for the same general item, such as different size saw blade guards in use or a part that has been updated on newer versions of the same machine.

PART NO. Column

Numbers Used — Part numbers can be indicated by a number, a blank entry, or TBD.

TBD (To Be Determined) is generally used to show a part that has not been assigned a formal part number at the time of publication.

A blank entry generally indicates that the item is not sold separately or is not sold by Multiquip. Other entries will be clarified in the “Remarks” Column.

NOTICE

The contents and part numbers listed in the parts section are subject to change without notice. Multiquip does not guarantee the availability of the parts listed.

NOTICE

When ordering a part that has more than one item number listed, check the remarks column for help in determining the proper part to order.

QTY. Column

Numbers Used — Item quantity can be indicated by a number, a blank entry, or A/R.

A/R (As Required) is generally used for hoses or otherparts that are sold in bulk and cut to length.

A blank entry generally indicates that the item is not sold separately. Other entries will be clarified in the “Remarks” Column.

REMARKS Column

Some of the most common notes found in the “Remarks” Column are listed below. Other additional notes needed to describe the item can also be shown.

Assembly/Kit — All items on the parts list with thesame unique symbol will be included when this item is purchased.

Indicated by:“INCLUDES ITEMS W/(unique symbol)”

Serial Number Break — Used to list an effective serial number range where a particular part is used.

Indicated by: “S/N XXXXX AND BELOW”“S/N XXXX AND ABOVE”“S/N XXXX TO S/N XXX”

Specific Model Number Use — Indicates that the part is used only with the specific model number or model number variant listed. It can also be used to show a part is NOT used on a specific model or model number variant.

Indicated by:“XXXXX ONLY”“NOT USED ON XXXX”

“Make/Obtain Locally” — Indicates that the part can be purchased at any hardware shop or made out of available items. Examples include battery cables, shims, and certain washers and nuts.

“Not Sold Separately” — Indicates that an item cannot be purchased as a separate item and is either part of an assembly/kit that can be purchased, or is not available for sale through Multiquip.


HPLA/HPHA-SERIES 46" TROWEL 1 TO 3 UNITSWITH HONDA GX-340K1QAP2 ENGINE.

1 to 3 UnitsQty. ......P/N ........................... Description1 ...........20478 ................ GRIP, LEFT1 ...........20463 ................ GRIP, RIGHT2 ...........20856 ................ SAFETY SWITCH1 ...........20285 ................ CABLE STANDARD HANDLE1 ...........20297 ................ CABLE QUICK-PITCH™1 ...........21172 ................ THROTTLE CABLE4 ...........1157 A ............... BUSHING4 ...........1162 A ............... LUBE CAP4 ...........1167 A ............... SCREW4 ...........1456 .................. NUT4 ...........1875 .................. WASHER4 ...........1322 .................. SCREW1 ...........21046 ................ GASKET KIT1 ...........21047 ................ BEARING KIT4 ...........1247 .................. RUBBER GROMMET4 ...........1245 .................. SPACER1 ...........2827 .................. ARM (16-1/2")2 ...........0261 .................. BELT, A-31 (HPLA46411H)2 ...........1523 .................. BELT, A-28 (HPHA46411H)1 ...........10968 ................ THRUST COLLAR KIT2 ...........9807956846 ...... SPARK PLUG2 ...........17620ZH7023 ... TANK CAP2 ...........17210ZE3505 ... AIR CLEANER ELEMENT2 ...........17218ZE3505 ... FILTER OUTER

HPLA/HPHA-SERIES 46" TROWEL — SUGGESTED SPARE PARTS


HPLA/HPHA-SERIES 46" TROWEL — NAMEPLATE AND DECALS

NAMEPLATES AND DECALS


HPLA/HPHA-SERIES 46" TROWEL — NAMEPLATE AND DECALS

NAMEPLATE AND DECALS

NO. PART NO. PART NAME QTY. REMARKS1 1758 DECAL: QUICK-PITCH™ HANDLE 12 12405 DECAL: QUICK-PITCH™ HANDLE INSERT 23 20527 DECAL: QUICK-PITCH™ WARNING 14 20526 DECAL: QUICK-PITCH™ LATCH WARNING 15 2942 DECAL: MQ WHITEMAN 13" 16 1736 DECAL: ARROWS 17 1735 DECAL: PRE-LOAD INDICATOR 18 11246 DECAL: OIL CHECK ............................................. 1 ....... PART OF DECAL KIT P/N 126209 NAMEPLATE.......................................................... 1 ....... CONTACT MQ PARTS DEPT.10 1940 DECAL: MQ WHITEMAN (SMALL) 111 11092 DECAL: CE 112 11246 DECAL: GEAR DRIVE .......................................... 1 ....... PART OF DECAL KIT P/N 1262013 1492 DECAL: STANDARD HANDLE (FINISHER) 114 1147 DECAL: HELMET, FOOT AND GLOVE ................. 1 ....... PART OF DECAL KIT P/N 1262015 11246 DECAL: HOT ......................................................... 1 ....... PART OF DECAL KIT P/N 1262016 1261 DECAL: DO NOT LIFT 117 1848 DECAL: POWER TROWEL 118 2938 DECAL: METRIC 119 11246 DECAL: BELT DRIVE ........................................... 1 PART OF DECAL KIT P/N 12620

SEE DECAL ILLUSTRATIONS ON PAGE 12


HPLA/HPHA-SERIES 46" TROWEL — STANDARD HANDLE ASSY.STANDARD HANDLE ASSY.

1

1

2

3

4

109

5

40

6

7

8

11

12

45

13

27

15

1716

18

19

43

42

44

20 21

22

25

30

4131

32

33

28

26

29

2324

39

34

14

2

1

PART OF ENGINE ASSEMBLY.

APPLY THREAD LOCK (LOCTITE242 BLUE OR EQUIVALENT).

ASM

DETAIL “A”

DETAIL “B”

SEEDETAIL “A”

SEEDETAIL “B”

21

22

35

36

3738

2

3


HPLA/HPHA-SERIES 46" TROWEL — STANDARD HANDLE ASSY.STANDARD HANDLE ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 20463 GRIP, HANDLE RIGHT 12 20774 COVER, PAD HANDLE 13 20818 DECAL, STD PITCH ............................................1 ........ OBSOLETE ON LATER MODELS4* 20817 WHEEL, HAND HANDLE 15* 0281 BEARING, THRUST, NICE 607 16* 20282 BEARING, TROWEL CONTROL 17* 0122C SCREW, SHS 3/8-16 X 1/2 18* 3615 COLLAR, SET 3/4 ID 19* 1478 SHAFT, TROWEL CONTROL 110 20478 GRIP, HANDLE LEFT 111 12556 HANDLE, ADJUSTABLE 112 21171 THROTTLE 113 20439 WHEEL ASSY, HAND 114 1492 DECAL, CUSTOM 2 1/2 CHROME 115 20438 SCREW, HHC 3/8-16 X 5.00 116 0786 SCREW, BHC 1/4- 20 X 3/8 NYL PATCH, NP 117 0786A SPACER, .360 X 17/64 X 1/8L 118 20287 SLIDE BLOCK TROWEL CONTROL 119 20285 CABLE ASSY., LENGTH 48.29” STD FINISHER 120 20856 SWITCH ASSY, SAFETY STOP .........................1 ........ INCLUDES ITEM W/■21■ 1602 SCREW, RHM 10-24 X 3/8 122 20988 SCREW, FHSC PHILLIPS 8-32 X 1 1/4 123 20514 WIRE ASSY, SAFETY STOP SWITCH 124 1662 TIE, CABLE TY-RAP, BLACK 125# 20275 BLOCK, SUPPORT 126# 1118 PULLEY, SUPPORT BLOCK 127# 20279 PIN, SUPPORT BLOCK 3/8 X 1.59 128 21017 SCREW, HHC 3/8-16 X 3 1/2 FULL THREAD 129 1493 SCREW, HHC 3/8-16 X 3 1/4 130 12567 HANDLE, STD 131 2942 DECAL, MQ WHITEMAN, 13” 132 21173 HOUSING, CABLE 74” 133 20845 SWIVEL, THROTTLE CABLE 134 1116 NUT, BRASS JAM 5/16-18 235 10133 NUT, NYLOC 3/8-16 136 20392 BRACKET, LIFT TUBE 137 HANDLE, LIFT ASSY. ......................................... 1........ NO LONGER AVAILABLE38 DECAL, CAUTION, LIFT HANDLE ...................... 1........ NO LONGER AVAILABLE39 20280 BLOCK, CABLE ASSY. .......................................1 ........ INCLUDES ITEMS W/#40 20819 HAND WHEEL ASSY., PITCH CONTROL ...........1 ........ INCLUDES ITEMS W/*41 HANDLE ASSY., STD FINISHERS .....................1 ........ CONTACT SALES DEPT.42 20301 CABLE, CNTL 5/32 GALV AIRCRAFT 46.03" 143 20421 CLEVIS, BALL END CONTROL CABLE 144 A8638 END-BOLT, CNTL CABLE 145 21172 CABLE, THROTTLE 1


HPLA/HPHA-SERIES 46" TROWEL — QUICK-PITCH™ HANDLE ASSY.

QUICK-PITCH ™ T-HANDLE ASSY.

1

2

2

1



ASM

ASM

SEEDETAIL

“B”

SEEDETAIL “A”

DETAIL “A”

9 10

10

12

53

54

52

13

11

37

5

38

39

49

40

45

57

46

47

43

48

41

42

44

1516

17

18

19

14

2324

26

26

27 28

58

60

59

20

22

21

25

25

32

33

34

50

51

3556

55

36

11

7

8

6

61

1

2

4

3

30

31

29

DETAIL “B”


HPLA/HPHA-SERIES 46" TROWEL — QUICK-PITCH™ HANDLE ASSY.QUICK-PITCH HANDLE ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 20463 GRIP, HANDLE RIGHT 12 20774 COVER, PAD HANDLE 13 20478 GRIP, HANDLE LEFT 14 12556 HANDLE, ADJUSTABLE 15 20526 DECAL, LATCH WARNING 16 21171 THROTTLE 17* 20527 DECAL, Q.P. WARNING 18* 20389 HANDLE, QUICK-PITCH™ 19* 1746 TRIGGER, QP CHROMED 110* 12405 DECAL, WHITEMAN QUICK-PITCH™ 211 1729 PIN, ROLL 3/16 X 1 1/4 312* 1706 SPRING, ENCLOSED QP CLAMP 113* 20437 PIN, QP LATCH 114 4568 PIN, ROLL 3/16 X 1 115 1711 SHAFT, CONTROL QP 116 1719 BUSHING, PIVOT PLATE 117 20439 WHEEL ASSY., HAND 118 20438 SCREW, HHC 3/8-16 X 5.00 119+ 1731 PIN, ROLL 1/4 X 3/4 120+ 20443 ARM, SLIDE CONTROL 121+ 1709 CONNECTOR, QP CONTROL ARM 122+ 20269 LINKAGE, QP CONTROL 123+ 20276 PIN, ROLL 1/4 X 1 3/4 124 20856 SWITCH ASSY., SAFETY STOP ........................... 1 .................. INCLUDES ITEM W/■25■ 1602 SCREW, RHM 10-24 X 3/8 126 20988 SCREW, FHSC PHILLIPS 8-32 X 1 1/4 127 20514 WIRE ASSY., SAFETY STOP SWITCH 128 20297 CABLE ASSY., QP CONTROL, 45” 129 2942 DECAL, MQ WHITEMAN, 13” 130 1715 SPRING, COUNTER BALANCE 131 20270 BLOCK, QP ADJUSTMENT 132 1735 DECAL, PRELOAD TRIM INDICATOR 133 21017 SCREW, HHC 3/8-16 X 3 1/2 FULL THREAD 134 1662 TIE, CABLE, TY-RAP BLACK 135# 20275 BLOCK, SUPPORT 136# 1118 PULLEY, SUPPORT BLOCK 137# 20279 PIN, SUPPORT BLOCK 3/8 X 1.59 138 1493 SCREW, HHC 3/8-16 X 3 1/4 139 1737 SNAP RING, TRUARC #5100-50 140 1733 WASHER, 1/2 X 1/32, HARDENED 2


1

2

2

1



ASM

ASM

SEEDETAIL

“B”

SEEDETAIL “A”

DETAIL “A”

9 10

10

12

53

54

52

13

11

37

5

38

39

49

40

45

57

46

47

43

48

41

42

44

1516

17

18

19

14

2324

26

26

27 28

58

60

59

20

22

21

25

25

32

33

34

50

51

3556

55

36

11

7

8

6

61

1

2

4

3

30

31

29

DETAIL “B”

HPLA/HPHA-SERIES 46" TROWEL — QUICK PITCH™ HANDLE ASSY.


QUICK PITCH HANDLE ASSY.

NO. PART NO. PART NAME QTY. REMARKS41 1736 DECAL, ARROW 142 1718 NUT, QP TRIM CTRL ADJ 143 1732 BOLT, STRIPPER 3/8 X 1/2 144 1717 SCREW, QP TRIM ADJUSTMENT 145 12642 TUBE, MAIN HANDLE 146 1758 DECAL, PATENT QP 147 20845 SWIVEL, ENGINE THROTTLE CABLE 148 21173 HOUSING, THROTTLE CABLE 74” 149 DECAL, CAUTION, LIFT HANDLE .........................1 .................. NO LONGER AVAILABLE50 HANDLE, LIFT ASSY. ............................................1 .................. NO LONGER AVAILABLE51 20392 BRACKET, LIFT TUBE 152 10133 NUT, NYLOC 3/8-16 153 1116 NUT, BRASS JAM 5/16-18 254 20390 TRIGGER, QP ASSY. ............................................1 .................. INCLUDES ITEMS W/*55 20293 LINKAGE, QP CONTROL ASSY. ........................... 1 .................. INCLUDES ITEMS W/+56 20280 BLOCK, CABLE ASSY. ..........................................1 .................. INCLUDES ITEMS W/#57 HANDLE ASSY., MAIN...........................................1 .................. CONTACT SALES DEPT.58 20421 CLEVIS, BALL END CONTROL CABLE 159 A8638 END-BOLT, CNTRL CABLE 160 20271 CABLE, CNTL 5/32 GALV AIRCRAFT 43.19" 161 21172 CABLE, THROTTLE 1

HPLA/HPHA-SERIES 46" TROWEL — QUICK PITCH™ HANDLE ASSY.


HPLA/HPHA-SERIES 46" TROWEL — 4-BLADE SPIDER ASSY.

4-BLADE SPIDER ASSY.


4-BLADE SPIDER ASSY.

NO. PART NO. PART NAME QTY. REMARKS1* 12208 WEAR RING 12* 12778 FLANGE BEARING 13* 10793 THRUST COLLAR ............................................................. 1 ........... INCLUDES ITEMS W/#4* 1154A WEAR PLATE 15% 1157A BEARING INSERT 46% 0164B RADIUS HEAD 3/8- 16 x 1-1/4” ........................................ 4 ........... FULL THREAD7% 1875 INT. SHKP. WASHER 3/8” 48% 1876 JAM NUT 3/8- 16 .............................................................. 4 ........... CLASS 2B9% 0105 HHCS 5/16- 18 x 1-1/2” 810% 0161C LOCK WASHER 5/16” 811% 1162A LUBRA-CAP 412% 2827 TROWEL ARM EXTENDED, 16-1/2" 413% 1163 TROWEL ARM LEVER 414% 4164 ROLL PIN 5/16 x 1-3/4” 415% 1316 SPRING (RIGHT HAND) 416% 1161 SPIDER PLATE ONLY 117% 1322 RETAINING SCREW ASSY. 418% 1456 HEX NUT 3/8-16 119% 1167A SHSS 3/8-16 x 1-1/2” CONE POINT 120% 0166A LOCK WASHER 3/8” 421 1490 SPIDER PLATE ASSY. ..................................................... 1 ........... INCLUDES ITEMS W/%22*# 1471 THRUST COLLAR BUSHING 123 10968 THRUST BEARING KIT .................................................... 1 ........... INCLUDES ITEMS W/*

HPLA/HPHA-SERIES 46" TROWEL — 4-BLADE SPIDER ASSY.


HPLA/HPHA-SERIES 46" TROWEL — GEARBOX & ENGINE MOUNTS ASSY.GEARBOX & ENGINE MOUNTS ASSY.

1

2

6

3

4

5

1 2

34

5

6

6

7

79

10

11

12

1617

18

18

19

19

20

21

22

23

24

30

31

3139

40

41

32

3233

38

35

3736

34

25

26

2927

28

13

14

15

8

3

2

1

4

5

6

TORQUE TO 15 LB/FT.

APPLY SEALANT (LOCTITE572 OR EQUIVALENT).


GEARBOX ASSEMBLY

GASKET/SEAL KIT

BEARING KIT

SHIM AS NECESSARYFOR 0.005 TO 0.010INTPUT SHAFT ENDPLAY.

SHIM AS NECESSARYFOR 0.000 TO 0.003OUTPUT SHAFT ENDPLAY.

USE SPECIALLY FORMULATEDWHITEMAN GEARBOX LUBRICANTP/N 10065 OR ISO 680 CYLINDER OIL.

GEARBOXOIL

28 0Z.

QTY. 1

GEARBOX REQUIRES28 OZ. OF LUBRICATINGOIL FOR OPERATION.


HPLA/HPHA-SERIES 46" TROWEL — GEARBOX & ENGINE MOUNTS ASSY.GEARBOX & ENGINE MOUNTS ASSY.

NO. PART NO. PART NAME QTY. REMARKS1%* 0753 SEAL, OIL NATIONAL #470954 12% 0131A SCREW, HHC 1/4-20 X 3/4 43% 12876 FLANGE, INPUT SHAFT 14%* 20395 RING, O -139 BUNA N 15%* 20397 SHIM, INPUT 0.002 THICK 1

20398 SHIM, INPUT 0.003 THICK 120399 SHIM, INPUT 0.005 THICK 120400 SHIM, INPUT 0.010 THICK 120401 SHIM, INPUT 0.020 THICK 1

6%# 20466 BEARING, CUP, TIMKEN #LM11910 27%# 20465 BEARING, CONE, TIMKEN #LM11949 28% 0627 KEY, SQUARE 3/16 X 1 1/4 19% 1851 GEAR, WORM & SHAFT ASSY. 110% 12874 CASE, GEAR 111% 1132 VENT, AIR 112 0655 SCREW, HHC 5/16-18 X 3/4 113 0300B WASHER, FLAT 5/16 SAE 314% 20476 SCREW, HHC 1/4-28 X 3/8 215% 21033 SIGHT GLASS, 3/4 M PIPE STEEL 116% 0121A FITTING, PLUG 3/8 MP SQ HEAD 117% 1138 RING, SNAP, TRUARC 5100-112 118%# 20475 BEARING, CUP TIMKEN #M86610 219%# 20474 BEARING, CONE TIMKEN #M86647 220% 1140 GEAR, WORM, BRONZE 121% 20470 SHAFT, OUTPUT 122% 1139 KEY, WOODRUFF #21 HARDENED 123 1238 KEY, WOODRUFF #25 124%* 20402 SHIM, OUTPUT 0.002 THICK 1

20403 SHIM, OUTPUT 0.003 THICK 120404 SHIM, OUTPUT 0.005 THICK 120405 SHIM, OUTPUT 0.010 THICK 120406 SHIM, OUTPUT 0.020 THICK 1

25%* 20396 RING, O -257 BUNA N 126% 12875 COVER, GEARBOX 127% 10235 WASHER, C/S EXT. SHKP 428% 1146 SCREW, FHSC 5/16-18 X 1, NYLOC NP 429%* 0254 SEAL, OIL, NATIONAL #470712 1


HPLA/HPHA-SERIES 46" TROWEL — GEARBOX & ENGINE MOUNTS ASSY.

1

2

6

3

4

5

1 2

34

5

6

6

7

79

10

11

12

1617

18

18

19

19

20

21

22

23

24

30

31

3139

40

41

32

3233

38

35

3736

34

25

26

2927

28

13

14

15

8

3

2

1

4

5

6

TORQUE TO 15 LB/FT.

APPLY SEALANT (LOCTITE572 OR EQUIVALENT).


GEARBOX ASSEMBLY

GASKET/SEAL KIT

BEARING KIT

SHIM AS NECESSARYFOR 0.005 TO 0.010INTPUT SHAFT ENDPLAY.

SHIM AS NECESSARYFOR 0.000 TO 0.003OUTPUT SHAFT ENDPLAY.

USE SPECIALLY FORMULATEDWHITEMAN GEARBOX LUBRICANTP/N 10065 OR ISO 680 CYLINDER OIL.

GEARBOXOIL

28 0Z.

QTY. 1

GEARBOX REQUIRES28 OZ. OF LUBRICATINGOIL FOR OPERATION.

GEARBOX & ENGINE MOUNTS ASSY.


GEARBOX & ENGINE MOUNTS ASSY.

NO. PART NO. PART NAME QTY. REMARKS30 1150 ARM, YOKE 131 20802 RING, SNAP, TRUARC 5100-37 OR EQUIV. 232 20803 SPACER, .50 OD X .40 ID X 0.25L 233 20801 PIN, YOKE 134 20797 STATIONARY GUARD RING 135 1245 BUSHING, GUARD RING 436 10700 FRONT ENGINE MOUNT 137 1948 REAR ENGINE MOUNT 138 1247 GROMMET 1/4 X .875 ID X 1-5/8 OD 439 20407 GEARBOX ASSY. ..................................................1 .................. INCLUDES ITEMS W/%40 21046 GASKET/SEAL KIT ............................................... 1 .................. INCLUDES ITEMS W/*41 21047 BEARING KIT ........................................................1 .................. INCLUDES ITEMS W/#

HPLA/HPHA-SERIES 46" TROWEL — GEARBOX & ENGINE MOUNTS ASSY.


HPLA/HPHA-SERIES 46" TROWEL — ENGINE ASSY.ENGINE ASSY.


HPLA/HPHA-SERIES 46" TROWEL — ENGINE ASSY.

HPLA/HPHA-SERIES 46" TROWEL — ENGINE ASSY

ENGINE ASSY.NO. PART NO. PART NAME QTY. REMARKS1 1388 ENGINE 11HP HONDA GX340K1QAP2 12 1391 HHCS 5/16-24 x 1-1/2" 43 0161C LOCK WASHER 5/16" 44 0300B FLAT WASHER 5/16" 45 20845 SWIVEL, THROTTLE CABLE 16 0310 SQUARE KEY 1/4X1/4X1.1/2" 17 1488 WIRE, SAFETY SWITCH 18 1475 CONNECTOR, SPLICE TAP 19 1127 PULLEY, AK-66 X 3/4 ................................................ 1 ..........HPLA4648H9 0740 PULLEY, AK-51 X 3/4 ................................................ 1 ..........HPHA4648H10 0250 AUTOMATIC CLUTCH ASSY. ................................... 1 .......... INCLUDES ITEMS W/*11 0261 BELT, A31 GATES HPII ONLY ................................... 1 ..........HPLA4648H11 0152 3 BELT, A28 GATES HPII ONLY ................................... 1 ..........HPHA4648H12 1335 BELT GUARD 113 0181B LOCK WASHER 1/4" 214 2577 T-BOLT 1/4-20 215 1284 SCREW, HHC 3/8 - 16 X 1-1/2 216 0166A WASHER, LOCK 3/8 MED 217 20982 SCREW, FSCS 3/8 - 16 X 1-1/2 418 1480 WASHER, CS EXT. SHKP 3/8 419 1948 PLATE, REAR 11HP HONDA 120 10700 PLATE, FRONT, 11HP HONDA 121 1245 BUSHING, GUARD RING 422 1247 GROMMET, 1/4 X 7/8ID X 1-5/8OD 423* 0252 SPINDLE 1" BORE 124* 0456 BEARING, SHIELDED 125* 0251 CLUTCH HOUSING DRUM 126* 0458 BUSHING, CLUTCH HSING DRM 127* B1766 WEIGHT, CLUTCH ................................................... 4 ..........REPLACES P/N 045428* 0855 SPRING 129* 0253 PLATE, CLUTCH EXPANSION 130* 1868 SCREW, SHS 3/8-24X3/4, NOPLT ............................ 1 ..........REPLACES P/N 045731 LIFT STRAP ............................................................. 1 ..........CONTACT UNIT SALES DEPT./ACC.

................................................................................................ ITEM


HPLA/HPHA-SERIES 46" TROWEL — GUARD RING ASSY.

GUARD RING ASSY.


GUARD RING ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 20811 GUARD RING ASSEMBLY 12 1940 DECAL 1

HPLA/HPHA-SERIES 46" TROWEL — GUARD RING ASSY.


HPLA/HPHA-SERIES 46" TROWEL — STABILIZER RING ASSY.

STABILIZER RING ASSY.

1APPLY LOCTITE 242 BLUEOR EQUIVALENT.

SEE DETAIL “A”

DETAIL “A”4

3

2

4

5

1

1

1


STABILIZER RING ASSY.

NO PART NO PART NAME QTY. REMARKS1 0161C WASHER, LOCK, 5/16 MED 42 1237 SCREW, SCH 5/16-18 X 7/8, NYL, NP 43 1723 ROD END, 5/16-24 MALE 44 6014C NUT, HEX FINISH 5/16-24 85 1483 RING, STABILIZER, 16-1/2" ARM 1

HPLA/HPHA-SERIES 46" TROWEL — STABILIZER RING ASSY.


HPLA/HPHA-SERIES 46" TROWEL — BLADES & ARM ADJ. FIXTUREASSY. (OPTIONS)

BLADES & ARM ADJ. FIXTURE ASSY.


HPLA/HPHA-SERIES 46" TROWEL — BLADES & ARM ADJ. FIXTUREASSY.

BLADES & ARM ADJ. FIXTURE ASSY.NO. PART NO. PART NAME QTY. REMARKS20 COMBO FLOAT & FINISH BLADE ................. 4 ........ CONTACT UNIT SALES DEPT./ACC. ITEM20 ENDURO COMBO FLOAT &FINISH BLADE . 4 ........ CONTACT UNIT SALES DEPT./ACC. ITEM21 FLOAT BLADE ............................................... 4 ........ CONTACT UNIT SALES DEPT./ACC. ITEM22 FINISH BLADE ............................................... 4 ........ CONTACT UNIT SALES DEPT./ACC. ITEM22 ENDURO FINISH BLADE W/ROTATING ....... 4 ........ CONTACT UNIT SALES DEPT./ACC. ITEM23 0202 HHCS 5/16-18X1" RING 424 0201 GUARD RING LUG RING 426 1434 TROWEL LUG (FINISH BLADE ONLY) 427 1162A LUBRA-CAP 428 7281 STABILIZER RING 14 1/2" ARM 129 6014C HEX NUT 5/16-24 830 1237 HHCS 5/16-18X7/8" NY-LOC 431 0490 SHCS 7/16-14X1" 332 0487 SHCS 3/8-16X1/2" 2033 0489 GRINDING DISC HUB 134 0488 STONE MOUNT PLATE 135 GRINDING DISC STONE ONLY .................... 1 ........ CONTACT UNIT SALES DEPT./ACC. ITEM36 GRINDING DISC ASSY. ................................. 1 ........ CONTACT UNIT SALES DEPT./ACC. ITEM39 UNIVERSAL COMBO BLADE ........................ 4 ........ CONTACT UNIT SALES DEPT./ACC. ITEM39 ENDURO UNIVERSAL COMBO BLADE ....... 4 ........ CONTACT UNIT SALES DEPT./ACC. ITEM40 UNIVERSAL FINISH BLADE ......................... 4 ....... CONTACT UNIT SALES DEPT./ACC. ITEM40 ENDURO UNIVERSAL FINISH BLADE ......... 4 ........ CONTACT UNIT SALES DEPT./ACC. ITEM41 UNIVERSAL MOUNTING BAR ...................... 4 ........ CONTACT UNIT SALES DEPT./ACC. ITEM42 SNAP PIN 1/4"X1.3/4" .................................... 8 ........ CONTACT UNIT SALES DEPT./ACC. ITEM44 0166A LOCK WASHER 3/8" 446 TROWEL ARM ADJ. FIXTURE ASSY. ............ 1 ........ CONTACT UNIT SALES DEPT./ACC. ITEM47 REVERSIBLE COMBO BLADE ...................... 4 ........ CONTACT UNIT SALES DEPT./ACC. ITEM48 1723 MALE R.H. ROD END 5/16" 149 FLOAT DISC .................................................. 1 ........ CONTACT UNIT SALES DEPT./ACC. ITEM50 FLOAT DISC LATCH PIN ............................... 4 ........ CONTACT UNIT SALES DEPT./ACC. ITEM


HPLA/HPHA-SERIES 46" TROWEL — LIFTING BAIL ASSY. (OPTION)

LIFTING BAIL ASSY. (OPTION)


LIFTING BAIL ASSY. (OPTION)NO. PART NO. PART NAME QTY. REMARKS1 LIFTING BAIL ASSY. ........................... 1 ............ CONTACT UNIT SALES DEPT./ACC. ITEM2 10229 HHCS 5/16-24X1" 43 0161C LOCK WASHER 5/16" 44 LIFTING BAIL ASSY. ........................... 1 ............ CONTACT UNIT SALES DEPT. /ACC. ITEM5 0205 HHCS 3/8-16X1" 36 1394 FHSCS 3/8-16X1" 17 0166A LOCK WASHER 3/8" 3

HPLA/HPHA-SERIES 46" TROWEL — LIFTING BAIL ASSY. (OPTION)


HONDA GX-340K1QAP2 ENGINE — AIR CLEANER ASSY.

AIR CLEANER ASSY.


HONDA GX-340K1QAP2 ENGINE — AIR CLEANER ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 16271ZE2000 GASKET, ELBOW 12 17210ZE3505 ELEMENT, AIR CLEANER............................... 1 ................ INCLUDES ITEMS W/*3* 17218ZE3505 FILTER, OUTER 14 17231ZE3W00 COVER, AIR CLEANER 15* 17232891000 GROMMET, AIR CLEANER 16 17235ZH9N00 NOSE, MUFFLER 17# 17238ZE2310 COLLAR, AIR CLEANER 28# 17239ZE1000 COLLAR B, AIR CLEANER 19 17410ZH9N00 ELBOW, AIR CLEANER .................................. 1 ................ INCLUDES ITEMS W/#11 90203ZA0800 WINGNUT 6MM 112 90325044000 WINGNUT, TOOL BOX SETTING 113 934040602008 BOLT- WASHER 6 X 20 114 9405006000 NUT, FLANGE 6MM 2


HONDA GX-340K1QAP2 ENGINE — CAMSHAFT ASSY.CAMSHAFT ASSY.


HONDA GX-340K1QAP2 ENGINE — CAMSHAFT ASSY.

CAMSHAFT ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 14100ZE3020 CAMSHAFT ASSEMBLY ................................. 1 ................ INCLUDES ITEM W/*2 14410ZE3013 ROD, PUSH 23 14431ZE2010 ARM, VALVE ROCKER 24 14441ZE2000 LIFTER, VALVE 25 14451ZE1013 PIVOT, ROCKER ARM 26* 14568ZE1000 SPRING, WEIGHT RETURN 17 14711ZE3000 VALVE, INTAKE 18 14721ZE3000 VALVE, EXHAUST 19 14751ZE2003 SPRING, VALVE 210 14771ZE2000 RETAINER, INTAKE VALVE SPRING 111 14773ZE2000 RETAINER, EXHAUST VALVE SPRING 112 14775ZE2010 SEAT, VALVE SPRING 113 14781ZE2000 ROTATOR, VALVE 114 14791ZE2010 PLATE, PUSH ROD GUIDE 115 90012ZE0010 BOLT, PIVOT 8MM 216 90206ZE1000 NUT, PIVOT ADJ. 217 12209ZE8003 SEAL, VALVE STEM 1


HONDA GX-340K1QAP2 ENGINE — CARBURETOR ASSY.

CARBURETOR ASSY.


HONDA GX-340K1QAP2 ENGINE — CARBURETOR ASSY.CARBURETOR ASSY.

NO. PART NO. PART NAME QTY. REMARKS1* 16010ZE2812 GASKET SET 12* 16011ZA0931 VALVE SET, FLOAT 13* 16013ZA0931 FLOAT SET 14* 16015ZE8005 CHAMBER SET, FLOAT 15* 16016ZH7W01 SCREW SET 16* 16024ZE1811 SCREW SET, DRAIN 17* 16028ZE0005 SCREW SET B 18* 16044ZE3811 CHOKE SET 19* 16100ZE3V01 CARBURETOR ASSEMBLY (BE80B B) .......... 1 ................ INCLUDES ITEMS W/*10* 16124ZE0005 SCREW, THROTTLE STOP 111* 16166ZE3W50 NOZZLE, MAIN 112* 16172ZE3W10 COLLAR, SET 113* 16173001004 GASKET, FUEL STRAINER CUP 114 16211ZE3000 INSULATOR, CARBURETOR 115 16220ZA0702 SPACER, CARBURETOR 116 16221ZE3800 GASKET, CARBURETOR 117 16223ZE3800 GASKET, INSULATOR 118 16610ZE1000 LEVER, CHOKE (STANDARD) ......................... 1 ................ INCLUDES ITEM W/#19* 16953ZE1812 LEVER, VALVE 120* 16954ZE1812 PLATE, LEVER SETTING 121* 16956ZE1811 SPRING, VALVE LEVER 122* 16957ZE1812 GASKET, VALVE 123* 16967ZE0811 CUP, FUEL STRAINER 124* 93500030060H SCREW, PAN 3 X 6 225# 9430520122 PIN, SPRING 2 X12 126* 99101ZH70880 JET, MAIN #88 (OPTIONAL) 126* 99101ZH80800 JET, MAIN #90 (OPTIONAL) 126* 99101ZH80920 JET, MAIN #92 127* 99204ZE00350 JET SET, PILOT #35 1


HONDA GX-340K1QAP2 ENGINE — CRANKCASE COVER ASSY.

CRANKCASE COVER ASSY.


HONDA GX-340K1QAP2 ENGINE — CRANKCASE COVER ASSY.CRANKCASE COVER ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 06165ZE3000 GOVERNOR KIT (OPTIONAL) ......................... 1 ................ INCLUDES ITEMS W/♣2 11300ZE3602 COVER ASSY., CRANKCASE (Q TYPE) ........ 1 ................ INCLUDES ITEMS W/$3 11381ZE3801 GASKET, CASE COVER 14 15600ZG4003 CAP ASSEMBLY, OIL FILLER ......................... 1 ................ INCLUDES ITEMS W/*5 15600735003 CAP ASSEMBLY, OIL FILLER ......................... 1 ................ INCLUDES ITEMS W/%7* 15625ZE1003 GASKET, OIL FILLER CAP 18% 15625ZE1003 GASKET, OIL FILLER CAP 19$ 16510ZE3000 GOVERNOR ASSEMBLY ................................ 1 ................ INCLUDES ITEMS W/#10#♣$ 16511ZE8000 WEIGHT, GOVERNOR 311#♣$ 16512ZE3000 HOLDER, GOVERNOR WEIGHT 112#♣$ 16513ZE2000 PIN, GOVERNOR WEIGHT 313♣$ 16531ZE2000 SLIDER, GOVERNOR 115♣$ 90602ZE1000 CLIP, GOVERNOR HOLDER 116 90701HC4000 PIN, DOWEL 8X12 217$ 91201ZE3004 OIL SEAL 35X52X8 118♣$ 9410106800 WASHER, PLAIN 6MM 119 957010804000 BOLT, FLANGE 8X40 720$ 961006202000 BEARING, RADIAL BALL 6202 121$ 961006207000 BEARING, RADIAL BALL 6207 1


NO ART WORKAVAILABLE

HONDA GX-340K1QAP2 ENGINE — CONTROL ASSY.CONTROL ASSY.


CONTROL ASSY.

NO. PART NO. PART NAME QTY. REMARKS2 16551ZE3000 ARM, GOVERNOR 13 16555ZE3000 ROD, GOVERNOR 14 16561ZE3000 SPRING, GOVRNOR 15 16562ZE3000 SPRING, THROTTLE RETURN 16 16570ZE3W10 CONTROL ASSEMBLY (REMOTE) 18 16571ZE3W00 LEVER, CONTROL 19 16574ZE1000 SPRING, LEVER 110 16575ZE2W00 WASHER CONTROL LEVER 111 16576891000 HOLDER, CABLE 112 16578ZE1000 SPACER, CONTROL LEVER 114 16584883300 SPRING, CONTROL ADJUSTING 115 16592883310 SPRING, CABLE RETURN 116 16594883010 HOLDER, WIRE 117 90013883000 BOLT, FLANGE 6X12 218 90015ZE5010 BOLT, GOVERNOR ARM 119 90114SA0000 NUT, SELF- LOCK 6MM 120 90605230000 CIRCLIP 5MM 121 93500040060H SCREW, PAN 4X6 122 93500050320A SCREW, PAN 5X32 123 93500050160A SCREW, PAN 5X16 124 9405006000 NUT, FLANGE 6MM 1

HONDA GX-340K1QAP2 ENGINE — CONTROL ASSY.


HONDA GX-340K1QAP2 ENGINE — CYLINDER BARREL ASSY.

CYLINDER BARREL


CYLINDER BARREL ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 12000ZE3816 CYLINDER ASSEMBLY ................................... 1 ................ INCLUDES ITEMS W/*2 15510ZE2043 SWITCH ASSEMBLY OIL LEVEL 13 16541ZE3010 SHAFT, GOVERNOR ARM 16 90131896650 BOLT, DRAIN PLUG 27 90446KE1000 WASHER 8.2X17X0.8 19* 91201ZE3004 OIL SEAL 35X52X8 110* 91201ZE9003 OIL SEAL 8X14X5 111 91353671003 O- RING 13.5X1.5 (ARAI) 112 9405010000 NUT, FLANGE 10MM 113 9410912000 WASHER, DRAIN PLUG 12MM 214 9425110000 PIN, LOCK 10MM 115 957010601200 BOLT, FLANGE 6X12 216* 961006202000 BEARING, RADIAL BALL 6202 117 90013883000 BOLT, FLANGE 6X12 (CT200) 118 34150ZH7003 ALERT UNIT, OIL 1

HONDA GX-340K1QAP2 ENGINE — CYLINDER BARREL ASSY.


CYLINDER HEAD ASSY.

HONDA GX-340K1QAP2 ENGINE — CYLINDER HEAD ASSY.


CYLINDER HEAD ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 12200ZF6W00 CYLINDER HEAD ............................................ 1 ................ INCLUDES ITEMS W/*2* 12204ZE2306 GUIDE, VALVE OS (OPTIONAL) 13* 12205ZE2305 GUIDE, EX. VALVE OS (OPTIONAL) 14* 12216ZE2300 CLIP, VALVE GUIDE 15 12251ZE3W00 GASKET, CYLINDER HEAD 16 12310ZE3791 COVER, HEAD 17 12315ZE3840 TUBE, BREATHER 18 12391ZE2020 GASKET, CYLINDER HEAD COVER 110 90014ZE2000 BOLT, HEAD COVER 111 90042ZE8000 BOLT, STUD 8X131.5 212 92900080320E BOLT 2, STUD 8X32 213 90441ZE2010 WASHER, HEAD COVER 114 9430112200 PIN A, DOWEL 12X20 215 957011008000 BOLT, FLANGE 10X80 416 9807956846 SPARK PLUG BPR6ES (NGK) 1

HONDA GX-340K1QAP2 ENGINE — CYLINDER HEAD ASSY.


CRANKSHAFT ASSY.

HONDA GX-340K1QAP2 ENGINE — CRANKSHAFT ASSY.


CRANKSHAFT ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 13310ZE3601 CRANKSHAFT, Q- TYPE ................................. 1 ................ INCLUDES ITEM W/*5 13351ZE3010 WEIGHT, BALANCER 16 90745ZE2600 KEY 6.3X6.3X43 17* 961006207000 BEARING, RADIAL BALL 6207 1

HONDA GX-340K1QAP2 ENGINE — CRANKSHAFT ASSY.


HONDA GX-340K1QAP2 ENGINE — FAN COVER ASSY.FAN COVER ASSY.


HONDA GX-340K1QAP2 ENGINE — FAN COVER ASSY.FAN COVER ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 16731ZE2003 CLIP, TUBE 12 19610ZE3010ZB COVER, FAN *NH1* (BLACK) 13 19631ZE3W00 SHROUD 15 36100ZH7003 SWITCH ASSEMBLY, ENGINE STOP 17 90013883000 BOLT, FLANGE 6X12 (CT200) 68 90684ZA0601 CLIP, WIRE HARNESS 1


FLYWHEEL ASSY.

HONDA GX-340K1QAP2 ENGINE — FLYWHEEL ASSY.


FLYWHEEL ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 19511ZE3000 FAN, COOLING 12 28450ZE3W11 PULLEY, STARTER (SCREEN GRID) 14 31100ZE3701 FLYWHEEL 16 90201ZE3V00 NUT, SPECIAL 16MM 17 90741ZE2000 KEY, SPECIAL WOODRUFF 25X18 1

HONDA GX-340K1QAP2 ENGINE — FLYWHEEL ASSY.


FUEL TANK ASSY.

HONDA GX-340K1QAP2 ENGINE — FUEL TANK ASSY.


FUEL TANK ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 16854ZH8000 RUBBER, SUPPORTER 107MM 12 16955ZE1000 JOINT FUEL TANK 13 17510ZE3010ZB TANK, FUEL "NH1" (BLACK) 15 17620ZH7023 CAP, FUEL FILLER .......................................... 1 ................ INCLUDES ITEM W/*6* 17631ZH7993 GASKET, FUEL FILLER CAP 17 17672ZE2W01 FILTER, FUEL 110 91353671003 O- RING 13.5X1.5 (ARAI) 111 9405008000 NUT, FLANGE 8MM 212 950014500360M BULK HOSE, FUEL (4.5X3000) (4.5X235) 113 9500202080 CLIP, TUBE B8 214 957010802500 BOLT, FLANGE 8X25 2

HONDA GX-340K1QAP2 ENGINE — FUEL TANK ASSY.


HONDA GX-340K1QAP2 ENGINE — IGNITION COIL ASSY.

IGNITION COIL ASSY.


IGNITION COIL ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 30500ZE2023 COIL ASSEMBYL, IGNITION 12 30700ZE1013 CAP ASSEMBLY, NOISE SUPPRESSOR 14 31512ZE2000 GROMMET, WIRE 17 36101ZE2701 WIRE, STOP SWITCH 430MM 110 90015883000 BOLT, FLANGE 6X28 2

HONDA GX-340K1QAP2 ENGINE — IGNITION COIL ASSY.


HONDA GX-340K1QAP2 ENGINE — MUFFLER ASSY.

MUFFLER ASSY.


MUFFLER ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 18310ZE3W00 MUFFLER 12 18320ZE3W01 PROTECTOR, MUFFLER 13 18323ZE3W40 PROTECTOR, EXHAUST PIPE 14 18330ZE2W00 PIPE, EXHAUST 15 18331ZE3810 CAP, MUFFLER 16 18333ZF6W01 GASKET, EXHAUST PIPE 18 18355ZE3010 ARRESTER, SPARK 19 18381ZE2W10 GASKET, MUFFLER (ARRESTER) 111 90013883000 BOLT, FLANGE 6X12 (CT200) 112 90050ZE1000 SCREW, TAPPING 5X8 613 90055ZE1000 SCREW, TAPPING 4X6 314 93500060060B SCREW, PAN 6X6 115 9405008000 NUT, FLANGE 8MM 5

HONDA GX-340K1QAP2 ENGINE — MUFFLER ASSY.


HONDA GX-340K1QAP2 ENGINE — PISTON ASSY.

PISTON ASSY.


HONDA GX-340K1QAP2 ENGINE — PISTON ASSY.PISTON ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 13010ZE3003 RING SET, PISTON (STANDARD) 11 13011ZE3003 RING SET, PISTON (OS 0.25 11 13012ZE3003 RING SET, PISTON (OS 0.50) 11 13013ZE3003 RING SET, PISTON (0.75) 12 13101ZE3W00 PISTON STANDARD 12 13102ZE3W00 PISTON (OS 0.25) 12 13103ZE3W00 PISTON (OS 0.50) 12 13104ZE3W00 PISTON (0.75) 13 13111ZF6000 PIN, PISTON 14 13200ZE3010 ROD ASSEMBLY, CONNECTING (STD.) 14 13200ZE3315 ROD ASSEMBLY, CONNECTING (US 0.25) 15 90001ZE8000 BOLT, CONNECTING ROD 26 90601ZE3000 CLIP, PISTON PIN 20MM 2


HONDA GX-340K1QAP2 ENGINE — RECOIL STARTER ASSY.RECOIL STARTER ASSY.


HONDA GX-340K1QAP2 ENGINE — RECOIL STARTER ASSY.RECOIL STARTER ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 28400ZE3W01ZB STARTER ASSY., RECOIL "NH1" .................. 1 ................ BLACK2 28410ZE3W01ZB CASE, RECOIL STARTER "NH1" .................... 1 ................ BLACK3 28421ZE3W01 PULLEY, RECOIL STARTER 14 28422ZE2W01 RATCHET, STARTER 25 28441ZE2W01 SPRING, FRICTION 16 28442ZE2W01 SPRING, STARTER RETURN 17 28443ZE2W01 SPRING, RATCHET 28 28444ZE2W01 RETAINER, SPRING 19 28445ZE2W01 HOLDER, SPRING 110 28461ZE2W02 GRIP, STARTER 111 28462ZE3W01 ROPE, RECOIL STARTER 112 28469ZE2W01 GRIP, REINFORCEMENT 113 90004ZE2W01 SCREW, CENTER 114 957010600800 BOLT, FLANGE 6X8 3


HONDA GX-340K1QAP2 ENGINE — LABELS ASSY.LABELS ASSY.


HONDA GX-340K1QAP2 ENGINE — LABELS ASSY.LABELS ASSY.

NO. PART NO. PART NAME QTY. REMARKS1 87521ZE3W01 EMBLEM 13 87522ZH9000 LABEL, CAUTION 14 87528ZE2810 MARK, CHOKE (EXTERNAL) 16 87532ZH8810 MARK, OIL ALERT (E) 19 89218ZE1000 WRENCH, SPARK PLUG 1


PAYMENT TERMSTerms of payment for parts are net 30 days.

FREIGHT POLICYAll parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin. Multiquip’s responsibility ceases when a signed manifest has been obtained from the carrier, and any claim for shortage or damage must be settled between the consignee and the carrier.

MINIMUM ORDERThe minimum charge for orders from Multiquip is $15.00 net. Customers will be asked for instructions regarding handling of orders not meeting this requirement.

RETURNED GOODS POLICYReturn shipments will be accepted and credit will be allowed, subject to the following provisions:

A Returned Material Authorization 1. must be approved by Multiquip prior to shipment.

To obtain a Return Material Authorization, 2. a list must be provided to Multiquip Parts Sales that defines item numbers, quantities, and descriptions of the items to be returned.

The parts numbers and descriptions a. must match the current parts price list.

The list must be typed or computer b. generated.

The list must state the reason(s) c. for the return.

The list must reference the sales d. order (s) or invoice (s) under which the items were originally purchased.

The list must include the name e. and phone number of the person requesting the RMA.

A copy of the Return Material Authorization 3. must accompany the return shipment.

Freight is at the sender’s expense. All 4. parts must be returned freight prepaid to Multiquip’s designated receiving point.

Parts must be in new and resalable 5. condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked.

The following items are not returnable:6.

Obsolete parts. (If an item is in the a. price book and shows as being replaced by another item, it is obsolete.)

Any parts with a limited shelf life b. (such as gaskets, seals, “O” rings, and other rubber parts) that were purchased more than six months prior to the return date.

Any line item with an extended c. dealer net price of less than $5.00.

Special order items.d.

Electrical components.e.

Paint, chemicals, and lubricants.f.

Decals and paper products.g.

Items purchased in kits.h.

The sender will be notified of any material 7. received that is not acceptable.

Such material will be held for five 8. working days from notification, pending instructions. If a reply is not received within five days, the material will be returned to the sender at his expense.

Credit on returned parts will be issued 9. at dealer net price at time of the original purchase, less a 15% restocking charge.

In cases where an item is accepted, for 10. which the original purchase document can not be determined, the price will be based on the list price that was effective twelve months prior to the RMA date.

Credit issued will be applied to future 11. purchases only.

PRICING AND REBATESPrices are subject to change without prior notice. Price changes are effective on a specific date and all orders received on or after that date will be billed at the revised price. Rebates for price declines and added charges for price increases will not be made for stock on hand at the time of any price change.

Multiquip reserves the right to quote and sell direct to Government agencies, and toOriginal Equipment Manufacturer accounts who use our products as integral parts of their own products.

SPECIAL EXPEDITING SERVICEA $35.00 surcharge will be added to the invoice for special handling including busshipments, insured parcel post or in cases where Multiquip must personally deliver the parts to the carrier.

LIMITATIONS OF SELLER’S LIABILITYMultiquip shall not be liable hereunder fordamages in excess of the purchase price of the item with respect to which damages are claimed, and in no event shall Multiquip be liable for loss of profit or good will or for any other special, consequential or incidental damages.

LIMITATION OF WARRANTIESNo warranties, express or implied, are made in connection with the sale of parts or trade accessories nor as to any engine not manufactured by Multiquip. Such warranties made in connection with the sale of new, complete units are made exclusively by a statement of warranty packaged with such units, and Multiquip neither assumes nor authorizes any person to assume for it any other obligation or liability whatever in connection with the sale of its products. Apart from such written statement of warranty, there are no warranties, express, implied or statutory, which extend beyond the description of the products on the face hereof.

Effective: February 22, 2006

TERMS AND CONDITIONS OF SALE — PARTS


NOTE PAGE

OPERATION AND PARTS MANUAL

Your Local Dealer is:

HERE’S HOW TO GET HELPPLEASE HAVE THE MODEL AND SERIAL

NUMBER ON-HAND WHEN CALLING

© COPYRIGHT 2010, MULTIQUIP INC.

Multiquip Inc, the MQ logo and the Whiteman logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All othertrademarks are the property of their respective owners and used with permission.

This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.

The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained inthis manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any obligations.

UNITED STATESMultiquip Corporate Office MQ Parts Department

18910 Wilmington Ave.Carson, CA 90746 Contact: [email protected]

Tel. (800) 421-1244Fax (800) 537-3927

800-427-1244310-537-3700

Fax: 800-672-7877Fax: 310-637-3284

Mayco Parts Warranty Department

800-306-2926310-537-3700

Fax: 800-672-7877Fax: 310-637-3284

800-421-1244, Ext. 279310-537-3700, Ext. 279

Fax: 310-537-1173

Service Department Technical Assistance

800-421-1244310-537-3700

Fax: 310-537-4259 800-478-1244 Fax: 310-631-5032

MEXICO UNITED KINGDOM

MQ Cipsa Multiquip (UK) Limited Head Office

Carr. Fed. Mexico-Puebla KM 126.5Momoxpan, Cholula, Puebla 72760 MexicoContact: [email protected]

Tel: (52) 222-225-9900Fax: (52) 222-285-0420

Unit 2, Northpoint Industrial Estate, Global Lane,Dukinfield, Cheshire SK16 4UJContact: [email protected]

Tel: 0161 339 2223 Fax: 0161 339 3226

CANADA

Multiquip

4110 Industriel Boul.Laval, Quebec, Canada H7L 6V3Contact: [email protected]

Tel: (450) 625-2244Tel: (877) 963-4411 Fax: (450) 625-8664

OPERATION AND PARTS MANUAL - Multiquip Inc

Documents

Transcript of OPERATION AND PARTS MANUAL - Multiquip Inc