ODISHA SKILL DEVELOPMENT AUTHORITY bid... · ODISHA SKILL DEVELOPMENT AUTHORITY 3rd Floor, Niyojan...

1

ODISHA SKILL DEVELOPMENT AUTHORITY 3rd Floor, Niyojan Bhawan, Unit-III, Bhubaneswar,

Tel : +91 674 2391320, Email : [email protected]

Extension of Last date for Submission of Tender & Corrigendum

In reference to Odisha Skill Development Authority, Notice Inviting Tender

Loan 3539-IND: Odisha Skill Development Project (OSDP) dated 9th Oct

2019, it is notified that the last date for submission of the tender for

Packages in National Competitive Bidding (NCB) is extended upto 3:00 pm

23rd Nov 2020. Tender opening is on 23rd November 2020 at 4 PM.

Subject :Proceedings of Pre – Bid Meeting held On 19th October,2020

Reference :IFB No. Invitation for Bids No.: OSDA/WSC/Goods/M-3/2020 dated 09.10.2020

Ph-III Packages / Lots Under ADB Loan: 3539

1. A Pre Bid meeting was held on 19th Oct 2020 at 3 PM in virtual mode( due to Covid – 19

travel restrictions)for 10 NCB packages regarding procurement of III phase Equipment

for Electrical Technology lab at World skill center and four Govt. ITI, as per information

given below:

- Pkg 0025 - Electrical Lab at Govt. ITI Bhubaneswar (comprising of 4 lots)

- Pkg 0026 - Advance Welding Lab at Govt. ITI Cuttack

- Pkg 0027 - Mini Tool Room at Govt. ITI Puri(comprising of 4 lots)

- Pkg 0028 - Advance Automotive Workshop at Govt. ITI Berhampur(comprising of 5

lots)

- Pkg 0029 - Technician Mechatronics at Govt. ITI Cuttack(comprising of 5 lots)

- Pkg 0030 - Quality Engineering Lab at Govt. ITI Cuttack

- Pkg 0031,0032,0034 & 0035 - Electrical Technology lab for WSC

2. List of members present in the virtual meeting on behalf of OSDA and bidders is

enclosed in Annexure I and II respectively.

3. Mr Sanjay Padhi, GM(Projects) welcomed the participants and introduced the project and

officials present for the pre-bid meeting.

4. The prospective bidders were briefed by Dr S.K.Das, Dy. Dir WSC through a power point

presentation containing the key points about the project, packages/lots, instructions for

filling of bids etc..

5. It was explained to the bidders that some equipment have been grouped in to packages

comprising lots. Bidders are free to participate in any one lot or multiple lots under

package subject to fulfillment of evaluation and qualification criteria and other bidding

mailto:[email protected]

2

requirements.

6. It was clarified that the bid is invited from eligible and qualified bidder under ADB’s single

stage two- envelope bidding procedure, under which bidders are supposed to submit

Technical and Financial proposals in two separate envelopes in a specific order, manner

and only specific formats, as explained in the bid document.

7. It was further clarified that the bidders should provide Lot-wise Bid Security of required

amount and validity in the prescribed format, as in ITB ( Instruction to Bidders Sec — 1). The

bidders technical responsiveness shall be determined on the basis of parameters prescribed

in Section 3: Evaluation and Qualification Criteria.

8. The financial proposals of only Technical Responsive bidders shall be opened. The bidders are advised to quote the rates after thorough study of the Bidding Document especially the

specifications. Any discount offered on the quoted rates should be indicated in the Bid Form

itself and not elsewhere; otherwise that may not be considered in Bid Evaluation. Negotiations on quoted price will not be held under normal circumstances and therefore bidders should quote reasonable and competitive rates at the first instance.

9. The successful bidder shall have to deposit performance security in the form of an unconditional Bank Guarantee in the amount of Ten ( 10) percent of the Accepted Contract Price with

validity to be enough to cover extended warranty period also. 10. It was mentioned that the bidder may take benefit of Excise and Custom duty

exemptions as per the provision of clause number 14.7 of Section 2; therefore bidders are advised to quote their prices considering the Excise and Custom duty exemption benefit.

11. It was also explained that conditional offers and late bids will not be accepted.

12. Brands /make/ models/photographs for any equipment, if specified are indicative only. The bidder is

free to offer equivalent equipment of other brands/makes/models subject to fulfillment of technical

specifications provided in tbidding documents.

13. After the presentation some prospective bidders raised some queries which were taken

up by the officers of OSDA/ Govt ITI and ADB procurement expert.

14. Some prospective bidders sought clarification on the specification in more detail manner.

It was suggested that, the prospective bidders should send their queries in OSDA mail

by 12 Noon of 20.10.20. These queries shall be compiled and addressed in the form of a

corrigendum document and shall be uploaded in the website for information of all

prospective bidders.

The meeting ended with a vote of thanks to the chair and the members.

Encl : Annexure -I (List of members on behalf of OSDA)

Annexure -II (List of Prospective Bidders with contact details)

Annexure -III (Corrigendum)

Chief Executive Officer

Odisha Skill Development Authority

3

Annexure – I

List of members on behalf of OSDA

The following members attended the Virtual pre bid meeting held on 19.10.2020.

1. Sri Sanjay Padhi, GM Project

2. Dr S.K.Das, Dy. Dir WSC

3. Sri Bibhu Prasad Beura, GM Finance

4. Sri S.K.Goyal, ADB Procurement expert

5. Sri Sujogya Mishra, Dy Dir DTE&T

6. Sri H.K.Mohanty, Principal Govt ITI Cuttack

7. Sri R.K.Panigrahi, Principal Govt ITI Berhampur

8. Smt J.M.Satpathy, Principal Govt ITI Bhubaneswar

9. Sri A.N.Dey, Principal Govt ITI Puri

4

Annexure – II

Details of Prospective Bidders with Contact Details

The representatives following prospective bidders attended the Virtual pre bid meeting

held on 19.10.2020.

S.

No.

Name of the

Bidder

Name of the

Representativ

e

Email ID Contact No.

1. M/S Niyoindia Mrs. Purnima [email protected] 7057922291

2. M/S Fronius Mr. Himanshu

Panda

[email protected] 7030934100

3. M/S Lincon electric Mr. Nipin [email protected] 9789995606

4. M/S Scientech Mr. S. Pawar [email protected] 9755591500

5. M/S DMG Mori Mr. S

Krishnaswamy

srinivasan.krishnaswamy@dmgm

ori.com

9972846290

6. M/S Schneider

Electric

Mr Amarnath

Durgale

[email protected]

7947116187

7. M/S Tesca Mr. Ashutosh [email protected] 9413330765

8. M/S Labtech Mr. Deepak [email protected]

9. M/S NVIS Tech Mr. N Nagar [email protected]

10. M/S Anshuman

Tech

Mr. V Ravi [email protected]

11. M/S Techmech

Engineers

Mr. Niranjan [email protected]

m

12. M/S Eqac Alloys Mrs. Smruti

Nayak


13. M/S Festo India Mr. N. Mohan [email protected]

14. M/S Kitech

Technologies P Ltd

Mr. Ajit

Balkrishnan


15. M/S Janatics Mr. Arpit [email protected] 9971360666

16. M/S Kemppi Mr. Suman

Ghosh


17. M/S Impartech Mr. Shridhar [email protected]

18. M/S Jyoti Engineers Mr. Dhiraj Bhol [email protected]

19. M/S SMC India Mr. Brajesh [email protected] 9599915062

20. M/S Accurate Sales [email protected]

21. Sushoma

Electronics, Kolkata

Mr. Braja [email protected] 9831432654

mailto:[email protected]

5

Annexure III

Odisha Skill Development Authority (OSDA)

Niyojan Bhawan, Sriya Square, Unit 3, Bhubaneswar – 751 001, Odisha

Website: www.empmissionodisha.gov.in email: [email protected]

Corrigendum/Addendum/Response to Bid Queries 01

In reference to Invitation for Bid (IFB) dated 09.10.2020 under Odisha Skill

Development Project (OSDP) , Prebid meeting was held on 19th October 2020.

Prospective bidders had raised some queries. On the basis of that, certain

clauses/sub-clauses have been revised. The modified clause/response to queries

are as follows :

Sr. No. Package/Lot No

Description/Clause number

Bidder’s query OSDA Response

1. Common to all package

Bid Security 1. Please share the Beneficiary details to prepare the bank guarantee to submit the Earnest Money Deposit.

2. If someone is bidding in more than one lot can we submit original DD with any of the lot and copy of same with other lots.

1. ODISHA SKILL DEVELOPMENT AUTHORITY Payable at Bhubaneswar

2. Yes , it is accepted, provided the value of common DD is equivalent to the required amount.

2. Common to all package

Tender Fee Please share the Beneficiary details to prepare the Demand Draft to submit the Tender Fee.

ODISHA SKILL DEVELOPMENT AUTHORITY Payable at Bhubaneswar

3. Common to all packages

Bid submission and technical bid opening date

Prospective Bidder’s have requested for extension of bid submission date .

Bid submission date is extended upto 3 PM on 23.11.2020. Technical bid shall be opened at 4PM on 23.11.2020.

4. PKG 0029 ALL LOTS

Section 3 Evaluation and Qualification Criteria

We are into manufacturing of educational trainer equipment’s since 2005.We would like to inform you that and which you are very well aware that high value purchase Orders in Electronics and Electrical departments are very rare and few. In most cases orders are placed on the item wise and not package wise. So even if the Tender value may be of high value order value may be small. Moreover the Purchase

Condition of bid documents shall prevail

6

Order value of a single contract is half the amount of its total turnover that you asked for. We fail to understand how will it be possible for a company with say 34 Lakhs turnover have a purchase orders worth 17 lakhs and that to for three years. If this will be the criteria then a MSME will never get the opportunity to bid for such Reputed Organization’s High Value Bids like this and will never be able to grow. Being a MSME I feel like this criterion has been put to benefit some particular bidder.

5. PKG 0029 LOT 4

Section 6: Schedule of Supply Item D3 at Sl. No. 171

For this item in your tender document, you have mentioned point 3 Portable hydraulic pump for transparent hydraulic & point 4 (A) Transparent Hydraulic Component. Transparent hydraulics kit being not an industrially prevalent arrangement and Students cannot have proper knowledge of hydraulics. It has many disadvantages when compare with training kit which is having real industrial hydraulic components. The power pack of transparent hydraulic gives very less pressure 10 bar maximum which is equivalent to pneumatic pressure. Hydraulics means, it should be deal with more pressure at least 50 bar. This is very important as we want to reduce the skill gap by offering training on industry relevant equipment and not some demo equipment which is not appropriate. If a student learns hydraulics technology by using transparent kit, When he enter into his career, he will face lot of difficulties to handle a hydraulic machine and he will not have confidence to apply the acquired knowledge in the workplace. There is no advantage of the transparent hydraulic kit to see how the components are working. (This can be applicable for limited time only as due to OIL, transparency is lost after some time) And anyways this feature is already available in simulation software as animation. The information in software is much more comprehensive. By using

As the requirement is for transparent Hydraulic and electro hydraulic kit to assist visual and functional learning, therefore conditions of bid document shall prevail.

7

Hydraulic cut section items, student can understand the construction of major hydraulic components. Considering the above points, kindly remove the transparent kit and change it with real industrial hydraulics trainer. We are requesting to remove Transparent or keep transparent/non-transparent. As in industries only non- transparent Hydraulic Components are being used. Also there is no change in scope of learning using transparent or even non transparent components and accessories.

6. PKG 29 LOT 4

Section 6: Schedule of Supply Item D2 Sl No 170 Pneumatic Hydraulic Sensor Kit and Simulation Software with pnumetic simulation software.

Discrepancies in the qty mentioned for the components and quantity for complete set up. For Example in the item, qty mentioned for the Rolling Table is 2 & set up qty is mentioned 3 units so that total qty of Rolling tables that come with 3 sets would be 6 no & likes wise same will be applied to all the components mentioned. Please confirm Each Kit consist with required set of components with Quantity e.g Rolling Table 2 nos Power Supply 3 nos Please clarify if we must multiply quantity for each component with number of set quantity Rolling Table 2 nos multiply by 3 sets is equal to 6 rolling table Power Supply 3 nos multiply by 3 sets is equal to 9 nos Etc. Quantity mentioned under the description column looks more and unclear. Kindly clarify, whether the quantities mentioned in description column is total requirement or qty per set. Example-1: Rolling table: 2 x 3 = total 6 Tables Example-2: Power supply: 3x3 = total 9 power supplies Example-3: Aircleaning unit:3x3= total 9 air cleaning unit Kindly amend it how many quantities of each items required per set. It will be clear and

The rolling table to be purchased is 2 Nos. Power supply 3 Nos. Air cleaning Unit 3 Nos

8

easy to understand everyone.

7. PKG 29 LOT 4

Section 6, Schedule of Supply Sr. No. 172 Item No D4

For Example : In this item, qty mentioned for the Rolling table with twin-post with Storage drawer blocks for rolling table 3 Nos & set up qty is mentioned 5 units but as far as we understood and as per discussion held in the Prebid Meeting, you are looking to have 1 complete set of trainer kits which would consists of all the components mentioned in the specifications along with their quantity so that total qty of Rolling tables that come with 3 sets would be 15 no. & likes wise will be applied to all the components mentioned. Please confirm. Rolling table with twin-post with Storage drawer blocks for rolling table 3 Nos Rolling Table 3 nos multiply by 5 sets is equal to 15 rolling table. Please clarify if this is applicable to all components in the sets Quantity mentioned under the description column looks more and unclear. Kindly clarify, whether the quantities mentioned in description column is total requirement or qty per set. Example-1: Rolling table: 3 x 5 = total 15 Tables Example-2: Power supply: 5x5 = total 25 power supplies Kindly amend it how many quantities of each items required per set. It will be clear and easy to understand everyone.

The rolling table required to be purchased is 3 Nos Other items as per the number of kits i,e. 05 nos. each

8. PKG 29 LOT 4

Section: 6 , Schedule of Supply Point D5 (173) PLC kit for Electro-Hydraulic and Electo Pneumatic Trainer kits.

In the bidding document, it is mentioned as Mitsuibhi PLC 12 Input and 8 output , PLC software , Programming Cable , 2 mm Banana Cable , 24 V DC Power Supply In Industries, many reputed make PLCs are used. Any make PLC should be acceptable

Any compatible make fulfilling specifications shall be accepted.

9. PKG 29 LOT 4

Section: 6 , Schedule of Supply Point D4: Electro-Pneumatic control trainer kit with

In the bid document, it is mentioned as Set of 3 relays 5 Nos • It will include three relays with 24V coil and 4 switchable contacts. • Relay-active led. • 2mm terminals for use with snap

Accepted. 2mm/4mm terminals for use with snap connection cables.

9

required components connection cables. It shall be generalized to 2mm/4mm

10. PKG 29 LOT 4

Section 6, Schedule of Supply Point D9 (177) Simulation software for Electrical , electronics , pneumatics and Hydraulics

The specification required (libraries, programming, etc.,) is too specific of a particular make. It should be neutral in nature. Kindly amend the specification with generic details. The main idea for learning is Simulation of Pneumatic, Hydraulic, Electrical Simulation and that is the core of requirement and learning for the students.

Not Accepted. Conditions of bid document shall prevail.

11. PKG 29 LOT 1

Section: 6 , Schedule of Supply

As this lot is mostly consists of tools which are easily available in market so providing the Authorizations for same is not possible. Hope it will acceptable.

Not Acceptable. Conditions of bid document shall prevail.

12. PKG 32 Section 3: Qualification and evaluation Criteria

As per requirement of criteria mentioned in clause 2.3.1 in section 3 i.e. 2.3.1 Contractual Experience-PO Criteria requirement in Last 5 year 3 contracts each Rs. 2,05,14,764/-. And with reference to the virtual meeting held on 19/10/2020 at 3.00PM modification in criteria should be required. We are MSME ISO 9001-2015 Company. Our turnover is more than double as per qualification however PO Criteria requirement for 03 single contracts 2,05,14,764/- is Very high. We request you kindly consider and change this criteria upto 1.3 Crore for MSME Company.

Conditions of Bid document shall prevail.

13. PKG 29 LOT 3

Section: 6 Schedule of Supply Mechatronics Lab outfit Item No C17 & C43 Item Name : Optical Transducer Trainer kit :

For this item C17 & C43 in your tender document, you have mentioned Output Circuits: 1. Digital Voltmeter 2.Relay 3. LED

Offered solution will come with following output circuitry: Digital Voltmeter/Relay/LED Hope it will be acceptable and considerable Please confirm.


10

14. PKG 29 LOT 3 Item No C16 Item Name : AC / DC Motor speed control trainer kit

For this item C16 in your tender document, you have mentioned System contains PID Controller for controlling the speed of DC Motor

Offered solution will come with PID Controller/ Operational Amplifier Hope it will be acceptable and considerable. Please confirm.


15. PKG 29 LOT 4

D9 (177) Simulation software for Electrical , electronics , pneumatics and Hydraulics

The specification required (libraries, programming, etc.,) is too specific of a particular make. It should be neutral in nature. Kindly amend the specification with generic details. The main idea for learning is Simulation of Pneumatic, Hydraulic, Electrical Simulation and that is the core of requirement and learning for the students.


16. PKG 31 A5 Ammeter Clip on Digital, 300A

This is clamp meter rated 300A ?. You have mentioned Clip. Is it the same. Please furnish Image

YES 300A

17. PKG 31

A6 Ammeter Clamp on, 400A

This is clamp meter rated 400A ? Up to 400A

18. PKG 31 A16 Power factor meter Portable

Please clarify whether equipment required need to be table mounted type or panel mounted type ?

PORTABLE (TABLE TOP)

19. PKG 31 A18 Voltmeter- AC, portable type, 300V



20. PKG 31

A19 Voltmeter -AC, portable, 500V



21. PKG 31

A20 Voltmeter -DC, portable, 300V



11

22. PKG 31

A21 Wattmeter-Single phase, portable, 10A, 240V



23. PKG 31

A22 Wattmeter-Three phase, portable



24. PKG 31

A29 Circuit breaker - Molded case - 30 A TPN - Metal clad enclosure

Please clarify whether the MCCB required is TPN ? Give Details for Metal clad enclosure required. Also clarify whether the enclosure required is floor mounting type or wall mounting type

MCCB is TPN, wall mounted and Metal clad enclosure is required.

25. PKG 31

A30 Distribution board - 32 A TPN 2-way, c/w MCCB, RCCB, MCBs, and surge arrestor – Metal clad enclosure

Ratings and quantity of MCB, RCCB, MCCB, Surge Arrestor and enclosure need to be specified.

32A TPN MCB(not MCCB) – 2nos. 32A TPN RCCB -2 nos. 20A SPN MCB -2nos 10A MCB- 2 nos

26. PKG 31

A31 Electrical consumer unit - Insulated enclosure - 30 A SPN 4-way, single-phase, c/w isolator, RCCB, MCBs and surge arrestor

Ratings and quantities of isolator, RCCB, MCB, surge arrestor and insulated enclosure is required

As per ISI or equivalent standard residential consumer unit

12

27. PKG 31

A32 Electrical consumer unit - Metalclad enclosure - 30 A SPN 4-way, single-phase - Isolator, RCCB, MCBs and surge arrestor

Ratings and quantities of isolator, RCCB, MCB, surge arrestor and metal clad enclosure is required

Metal clad enclosure 4 way dust proof, MCB 415 V 32 Amp TPN, RCCB 415 V 32 Amp 300mA, Surge arrester 320 V 20 KA TPN.

28. PKG 31

A34 Fire alarm panel - Call points, sounders, smoke detectors, heat detectors

Please clarify whether the Components of the fire alarm system need to be Supplied loose or mounted and wired on a panel ?

To be supplied mounted on panel & all items wired up together.

29. PKG 31

A42 Meter board - Singlephase, metalclad - Complete with accessories and energy meter

Details of accessories to be mounted on single phase meter board to be specified, BoM to be provided

As per ISI or equivalent standard residential consumer unit with all required accessories.

30. PKG 31

A43 Meter board – Three phase, metal clad - Complete with accessories and

Details of accessories to be mounted on three phase meter board to be specified, BoM to be provided

As per ISI or equivalent standard consumer unit with all required accessories.

13

energy meter

31. PKG 31

A50 Protection relay - Overcurrent, IDMTL type

Please clarify whether only relay unit to be supplied or Simulating panel to operate the relay is proposed.

Simulating panel is required.

32. PKG 31

A51 Protection relay - Earth fault, IDMTL type

Please clarify whether only relay unit to be supplied or Simulating panel to operate the relay is proposed.

Simulating panel is required.

33. PKG 31

A49 Primary current injection set - 2,000A

Dangerous for students handling hence we suggest 20A for experimentation.

Up to 200A capacity required.

34. PKG 31

A50 & A51 Protection relay - Overcurrent, IDMTL type & Protection relay - Earth fault, IDMTL type

Your item A50, A51 mention only relay will not be useful for training hence we suggested IDMT Over Current Relay with built in test kit like primary current injection set, timer for time measurement and current measurement must be required.

IDMT Over Current Relay with built in test kit like primary current injection set, timer for time measurement and current measurement is required.

35. PKG 31

A52 Secondary current injection set - 50A

Secondary current injection set should be part of training kit of A50, A51. Only 2 nos secondary current injection set not useful. You should purchase at least 5.

Only 2 numbers is required.

14

36. PKG 32

B5 Electrical AC drive training unit - I/O console - Portable profile structure

Drive capacity to be specified. Bill of material to be detailed

Based on the

existing profile

structure the

information of the

drive is

ATV58EU09M2

Input V: 200/240V;

Input phase: 1;

Input

current:5.6/4.7A;

Input Fuse: Type

CC or J 10A max

Output 3 Ph:

200/240V; output

current: 2.3A;

Output current

maximum

transient (1mn):

3.1A; output

frequency: 0.1 -

500 Hz

37. PKG 32

B7 Motor starter system- Portable wiring board- Contactors, indicating lamps, isolators, push buttons, relays, timers, MCBs and terminal blocks

Referring to the scope of supply image is missing as mentioned. Bill of material to be specified.

Bills of material as

per the items shown

in the picture

15

38. PKG 32

B9 Autotransformer starter -400V, 4 taps

kVA capacity to be specified.

2 KVA

39. PKG 32

B10 Electrical motor fault training simulator -Three phase, 0.75 Kw - Flywheel

Details about the product reference or bill of material to be specified.

Three phase, 0.75 Kw - Flywheel

40. PKG 32

B11 Single-phase induction motor Demonstration model

Image requested, is cut section of a motor expected? Also please specify the frame size of the motor required

Pl refer Serial no 68 for the image. Cut model of an 2 HP, 230 V induction Motor, Both Slip ring type and Squirrel cage type. Frame size as per the dimension of the motor.

41. PKG 32

B12 Three-phase induction motor Star/delta testing

Bill of material is required to be specified.

1 nos. -3 phase MCB, 3nos - 3 phase contactors, 1 no. - overload relay, 1no.- timer, 1no.- start stop button and 1no.- emergency button.

16

42. PKG 32

B13 Programmable logic controller system

Please clarify whether the PLC controller to be supplied loose or mounted on a panel. Please specify the number of I/O required with Type of I/O's

It shall be mounted on the panel. Number of I/O & type as per specific model.

43. PKG 32

B14 PLC training system - Programmable logic controller - Panel approx 600mm x 300mm - Contactors c/w O/L relay - Terminal blocks, MCBs, DIN rail

Please clarify whether this only the panel for the PLC's specified in B13 or do you require PLC's to be supplied as well in this scope

PLC also to be

supplied.

44. PKG 32

B15 I/O devices interface training unit

Image requested for this line item, type of I/O to be specified, quantity to be specified. Please specify which type of interface is required, and whether it is to connect field devices

Image Same as above as per PLC training kit. Quantity – 20 nos. I/O Type – Ethernet/Profinet/USB I/O Number – Min Input 8 nos, Min Output 6 nos Upto 24nos (Both Input & output)

45. PKG 32

B17 Electrical main switchboard

Aux. cables- sizes and length to be specified.

AS per ISI or equivalent Standard.

46. PKG 31 A5 Ammeter Clip on Digital, 300A

Missing photograph

17

47. PKG 31 A6 Ammeter Clamp on Digital

Missing photograph

48. PKG 31 A7 Galvanometer Missing photograph

49. PKG 31

A14 Phase sequence test instrument - Digital, c/w accessories

Missing photograph

50. PKG 31 A16 Power factor meter-Portable

Missing photograph

51. PKG 31 A17 Rheostat -Assorted ranges

Missing photographs

52. PKG 31

A23 Earth electrode resistance test instrument

Missing photographs

18

53. PKG 31 A30 Distribution board - 32 A TPN 2-way

Missing photographs

54. PKG 31

A31 Electrical consumer unit - Insulated enclosure

Missing photographs

55. PKG 31

A32 Electrical consumer unit – Metal clad enclosure

Missing photographs

56. PKG 31 A49 Primary current injection set

Missing photographs

57. PKG 31

A50 Protection relay - Overcurrent, IDMTL type

Missing photographs

19

58. PKG 31 A52 Secondary current injection set - 50A

Missing photographs

59. PKG 32 B1 Power supply unit -DC

Missing photographs

60. PKG 32 B3 Transformer -Variable, single phase

Missing photographs

61. PKG 32 B4 Transformer -Variable, three phase

Missing photograph

20

62. PKG 32

B5 Electrical AC drive training unit - I/O console - Portable profile structure

Missing photograph

63. PKG 32

B6 Motor soft starter -Three-phase, 1 kW

Missing photograph

64. PKG 32

B7 Motor starter system- Portable wiring board- Contactors, indicating lamps, isolators, push buttons, relays, timers, MCBs and terminal blocks

Missing photograph

65. PKG 32

B8 Three-phase induction motor - For training in servicing and repair

Missing photographs

21

66. PKG 32

B9 Autotransformer starter -400V, 4 taps

Missing photographs

67. PKG 32

B10 Electrical motor fault training simulator -Three-phase, 0.75 Kw - Flywheel

Missing photographs

22

68. PKG 32

B11 Single-phase induction motor -Demonstration model

Missing photograph

69. PKG 32

B14 PLC training system - Programmable logic controller - Panel

Missing photographs

70. PKG 0032

B17 Electrical Main switch Board

Missing photographs

23

71. PKG 0035

E11 Electrical wiring stations - For electrical installation and control projects - With electrical supply system

Missing photographs

ODISHA SKILL DEVELOPMENT AUTHORITY bid... · ODISHA SKILL DEVELOPMENT AUTHORITY 3rd Floor, Niyojan...

Documents

Transcript of ODISHA SKILL DEVELOPMENT AUTHORITY bid... · ODISHA SKILL DEVELOPMENT AUTHORITY 3rd Floor, Niyojan...