OC GPS APPLICATION LIST FOR GPS LAP TIMER ORIGINAL … GPS ITA EN.pdf · All the wires you need to...
2
OC GPS General Characteristics GPS receiver equipped with antenna, prepared to save the finish line position on the track in automatic mode, works with all original dashboard present in application list. Wiring and fitting Fit the antanna GPS on vehicle, that must be ABSOLUTELY IN HORIZONTAL POSITION without hurdles over and around. There is also a cable with four wires, WHITE, GREEN,BROWN AND YELLOW connect them following the application list here in attachment with extreme care to the wires colours on the bike. If you have some trouble, please check under the push button of yr lap timer and check the wires connected, at this time, with a voltmeter (tester) measure the polarity of voltage between the wire present into the switch, the positive 12+ connect the wire YELLOW and to the other (ground -) the BROWN. All the wires you need to connect are present behind the original dashboard in a big connector. Before to do all, remember to activate your Chrono function in dashboard ! Set up and use On the module is present a button. Turn On/Off: ON keep push untill led flash RED OFF Double quick push and Red led will flash for one second and module turn off. After turned on, the module will start to seach the Satellite link, and the led colour may vary in follow ways: RED FLASHING search satellite link LIGHT BLU FLASHING satellite linked at this time push for two second the but- ton when reseales start to blink GREEN FLASHING satellite link is operative and ready to work at this time is ready to store the finish line in automatic mode. Start your session and during the first lap the finish line will be memorized in automatic mode in the fasted section of the track, when stored the Led will be WHITE FLASHING for 5 seconds. The timekeeping will start to the end at the second laps. Note Use If you go in the same track don’t need to store every time the finish line, will be enought turn on the module and wait the satellite link connection, then is possi- ble to use it. The automatic mode to store the finish line isn’t avaiable with speed lower than 20 Km/h Warning Message During the turn on if the LED is YELLOW means the GPS module or antenna is broken. GPT ENGINEERING SAS Via Cadore 19 20831 SEREGNO (MONZA/BRIANZA) ITALY - [email protected] - www.gpt.it APPLICATION LIST FOR GPS LAP TIMER ORIGINAL DASHBOARD All the connections are in the main loom behind the dashboard This application isn’t exhaustive please check carefully the wiring connection on yr bike APRILIA Model Year Brown wire Yellow wire Green wire Power supply + White wire Ground - RS 125 95>97 Blue White/Green Green Dark Bleu RS 125 98>05 Blue White/Green Green Dark Bleu RS 125 06>10 Green Dark Bleu RS 250 95>97 White/Black White/Green Green/Red White/Black RS 250 98>02 White/Black White/Green Green/Red White/Black RS v1000 98>03 White/Bleu Green Green/Red Blu/verde RS v1000 04>08 White/Bleu Green/Red Green/Red Dark Bleu TUONO 02>05 White/Bleu Green Green Bleu/Green TUONO 06>10 Brown Grey/Green Green/Red Bleu/Green TUONO V4/V4 APCR 11>15 Bleu/Black Yellow/Pink Red/Brown Bleu/Green RSV4 09>12 Bleu/Black Yellow/Pink Green/Red Bleu/Green RSV4 APCR 11> 14 Bleu/Black Yellow/Pink Green/Red Bleu/Green RSV4 RR/RF 15>16 Bleu/Black Yellow/Pink Green/Red Bleu/Green KAWASAKI Model Year Wire Brown Yellow wire Green wire Power supply + White wire Ground - 636 03>06 White/Red Brown/White Brown/White Black/Yellow ZX 6 R 07>10 White/Red Brown/White Brown/White Black/Yellow ZX10 R 04>10 White/Red Brown/White Brown/White Black/Yellow ZX10 R 11>16 Red/Black Brown/White Brown/White Black/Yellow DUCATI Model Year Brown wire Yellow wire Green wire Power supply + White wire Ground - Monster 696/796/1100 all Yellow/Blue Red/Black Red/Black Black Hypermotard 1100 08>09 Yellow/Blue Red/Black Red/Black Black Hypermotard 796/1100 10>13 Yellow/Green Red/Black Red/Black Black Streetfighter all Blue Red/Black Red/Black Black/Green 899 Panigale 13>15 Orange pin 15 Red/Black pin 8 Red/Yellow pin 34 Black pin 33 959 Panigale 2016 Orange pin 15 Red/Black pin 8 Red/Yellow pin 34 Black pin 33 1199 Panigale 12>16 Orange pin 15 Red/Black pin 8 Red/Yellow pin 34 Black pin 33 1299 Panigale 14>16 Orange pin 15 Red/Black pin 8 Red/Yellow pin 34 Black pin 33 APPLICATION LIST FOR GPS LAP TIMER ORIGINAL DASHBOARD All the connections are in the main loom behind the dashboard This application isn’t exhaustive please check carefully the wiring connection on yr bike KTM Model Year Brown wire Yellow wire Green wire Power supply + White wire Ground - 1190 RC 8 R 2009 Brown Red Yellow/Orange Brown 1190 RC 8 R 2011 Brown White/red Orange Brown MV AGUSTA Model Year Brown wire Yellow wire Green wire Power supply + White wire Ground - F 3 11>15 Brown/White Yellow/Black Yellow/Black Blue F 4 11>15 White Bleu/Yellow Bleu/Yellow Blue TRIUMPH Model Year Brown wire Yellow wire Green wire Power supply + White wire Ground - STREET TRIPLE 675 09/12 White/Red Green/Red Green/Red Black DAYTONA 675 06/08 White/Red Green/Red Green/Red Black DAYTONA 675/ R 675 09/16 White/Red Green/Red Green/Red Black YAMAHA Model Year Brown wire Yellow wire Green wire Power supply + White wire Ground - R 1 09>14 Black/White Bleu/White Marrone Black/White R 1 - R 1M YEC 15>16 Black/White Yellow Red/White Black/White R 1- R 1M 15>16 Giallo/Nero Yellow Red/Yellow Black HONDA Model Year Brown wire Yellow wire Green wire Power supply + White wire Ground - - CBR 1000 RR 2018 Black/red yellow/red Brown/white Green Note: For the R1 2015, all connections must be done to the 6 pin connector of the Xenon eco, placed on the left front side of the Bike Product Code ID manufacturing date
Transcript of OC GPS APPLICATION LIST FOR GPS LAP TIMER ORIGINAL … GPS ITA EN.pdf · All the wires you need to...
OC GPS
General CharacteristicsGPS receiver equipped with antenna, prepared to save the finish line position on the track in automatic mode, works with all original dashboard present in application list.
Wiring and fitting
Fit the antanna GPS on vehicle, that must be ABSOLUTELY IN HORIZONTAL POSITION without hurdles over and around.
There is also a cable with four wires, WHITE, GREEN,BROWN AND YELLOW connect them following the application list here in attachment with extreme care to the wires colours on the bike.If you have some trouble, please check under the push button of yr lap timer and check the wires connected, at this time, with a voltmeter (tester) measure the polarity of voltage between the wire present into the switch, the positive 12+ connect the wire YELLOW and to the other (ground -) the BROWN.All the wires you need to connect are present behind the original dashboard in a big connector.
Before to do all, remember to activate your Chrono function in dashboard !
Set up and use
On the module is present a button.
Turn On/Off:
ON keep push untill led flash REDOFF Double quick push and Red led will flash for one second and module turn off.
After turned on, the module will start to seach the Satellite link, and the led colour may vary in follow ways:
RED FLASHING search satellite link
LIGHT BLU FLASHING satellite linked at this time push for two second the but-ton when reseales start to blink
GREEN FLASHING satellite link is operative and ready to work at this time is ready to store the finish line in automatic mode.
Start your session and during the first lap the finish line will be memorized in automatic mode in the fasted section of the track, when stored the Led will be WHITE FLASHING for 5 seconds. The timekeeping will start to the end at the second laps.
Note Use
If you go in the same track don’t need to store every time the finish line, will be enought turn on the module and wait the satellite link connection, then is possi-ble to use it.
The automatic mode to store the finish line isn’t avaiable with speed lower than 20 Km/h
Warning Message
During the turn on if the LED is YELLOW means the GPS module or antenna is broken.
GPT ENGINEERING SAS Via Cadore 19 20831 SEREGNO (MONZA/BRIANZA) ITALY - [email protected] - www.gpt.it
APPLICATION LIST FOR GPS LAP TIMER ORIGINAL DASHBOARD
All the connections are in the main loom behind the dashboard This application isn’t exhaustive please check carefully the wiring connection
on yr bike
APRILIA Model Year Brown wire Yellow wire Green wire Power supply +
White wire Ground -
RS 125 95>97 Blue White/Green Green Dark BleuRS 125 98>05 Blue White/Green Green Dark BleuRS 125 06>10 Green Dark BleuRS 250 95>97 White/Black White/Green Green/Red White/BlackRS 250 98>02 White/Black White/Green Green/Red White/Black
RS v1000 98>03 White/Bleu Green Green/Red Blu/verdeRS v1000 04>08 White/Bleu Green/Red Green/Red Dark BleuTUONO 02>05 White/Bleu Green Green Bleu/GreenTUONO 06>10 Brown Grey/Green Green/Red Bleu/Green
TUONO V4/V4 APCR 11>15 Bleu/Black Yellow/Pink Red/Brown Bleu/GreenRSV4 09>12 Bleu/Black Yellow/Pink Green/Red Bleu/Green
RSV4 APCR 11> 14 Bleu/Black Yellow/Pink Green/Red Bleu/GreenRSV4 RR/RF 15>16 Bleu/Black Yellow/Pink Green/Red Bleu/Green
KAWASAKI Model Year Wire Brown Yellow wire Green wire Power supply +
White wire Ground -
636 03>06 White/Red Brown/White Brown/White Black/YellowZX 6 R 07>10 White/Red Brown/White Brown/White Black/YellowZX10 R 04>10 White/Red Brown/White Brown/White Black/YellowZX10 R 11>16 Red/Black Brown/White Brown/White Black/Yellow
DUCATI Model Year Brown wire Yellow wire Green wire Power supply +
White wire Ground -
Monster 696/796/1100 all Yellow/Blue Red/Black Red/Black BlackHypermotard 1100 08>09 Yellow/Blue Red/Black Red/Black Black
Hypermotard 796/1100 10>13 Yellow/Green Red/Black Red/Black BlackStreetfighter all Blue Red/Black Red/Black Black/Green899 Panigale 13>15 Orange pin 15 Red/Black pin 8 Red/Yellow pin 34 Black pin 33
959 Panigale 2016 Orange pin 15 Red/Black pin 8 Red/Yellow pin 34 Black pin 33
1199 Panigale 12>16 Orange pin 15 Red/Black pin 8 Red/Yellow pin 34 Black pin 33
1299 Panigale 14>16 Orange pin 15 Red/Black pin 8 Red/Yellow pin 34 Black pin 33
APPLICATION LIST FOR GPS LAP TIMER ORIGINAL DASHBOARD
All the connections are in the main loom behind the dashboard This application isn’t exhaustive please check carefully the wiring connection
on yr bike
KTM Model Year Brown wire Yellow wire Green wire Power supply +
White wire Ground -
1190 RC 8 R 2009 Brown Red Yellow/Orange Brown1190 RC 8 R 2011 Brown White/red Orange Brown
MV AGUSTA Model Year Brown wire Yellow wire Green wire Power supply +
White wire Ground -
F 3 11>15 Brown/White Yellow/Black Yellow/Black BlueF 4 11>15 White Bleu/Yellow Bleu/Yellow Blue
TRIUMPH Model Year Brown wire Yellow wire Green wire Power supply +
White wire Ground -
STREET TRIPLE 675 09/12 White/Red Green/Red Green/Red BlackDAYTONA 675 06/08 White/Red Green/Red Green/Red Black
DAYTONA 675/ R 675 09/16 White/Red Green/Red Green/Red Black
YAMAHA Model Year Brown wire Yellow wire Green wire Power supply +
White wire Ground -
R 1 09>14 Black/White Bleu/White Marrone Black/WhiteR 1 - R 1M YEC 15>16 Black/White Yellow Red/White Black/White
R 1- R 1M 15>16 Giallo/Nero Yellow Red/Yellow Black
HONDA Model Year Brown wire Yellow wire Green wire Power supply +
White wire Ground - -
CBR 1000 RR 2018 Black/red yellow/red Brown/white Green
Note: For the R1 2015, all connections must be done to the 6 pin connector of the Xenon eco, placed on the left front side of the Bike
Product Code IDmanufacturing date
OC GPS
Fare riferimento alla tabella per il collegamento dei cavi ! Attivare la funzione Chrono sul Vostro cruscotto !
Caratteristiche generaliModulo completo di ricevitore satellitare e antenna, permette la memorizzazione del traguardo in modo automatico, utilizzando il cronometro originale presente nella strumentazione per il cronometraggio. Collegamenti e montaggio
Posizionate l’antenna GPS, che dovra’ ASSOLUTAMENTE essere collocata in posizione orizzontale, senza ostacoli sopra di essa.Maneggiatela con estrema cura.
Nella estremita’ opposta e’ presente un cavo quadripolare, BIANCO, VERDE, MARRONE E GIALLO, collegateli nella sequenza presente nella tabella allegata, nel caso di non funzionamento vi consigliamo di procedere come segue:Individuate i cavi che arrivano al pulsante manuale per il vs cronometro, con un tester misurate il voltaggio tra i due cavi, quindi collegate il cavo giallo dove e’ presente il 12v e il cavo marrone all’altro cavo, il negativo.I cavi presenti sulla moto si trovano nel connettore dietro il cruscotto relativo al comando della manopola dove e’ presente il pulsante per la presa dei tempi.
Utilizzo
Sul modulo e’ presente un pulsante.
Accensione modulo:
ON premete il pulsante fino all’accensione del led ROSSO LAMPEGGIANTE ( in attesa di link ai satelliti ) una volta che il link e’ attivo il led si colorera’ di AZZURRO ( Link satellite attivo) a questo punto dobbiamo memorizzare il traguardo.
Memorizzazione del traguardo:
Prima dell’ ingresso in pista premere il pulsante per due secondi fino a che il led diventa VERDE FISSO quindi rilasciare lo stesso, al rilascio inizierà a lampeg-giare sempre di colore VERDE ,indicando che lo strumento e’ pronto alla memo-rizzazione automatica del traguardo.Entrate in pista. Durante il primo giro il traguardo verrà automaticamente me-morizzato nel punto più veloce del tracciato, nel momento in cui si memorizza il led lampeggera’ BIANCO per 5 secondi .Il cronometraggio iniziera’ alla fine del secondo giro nel punto in cui è stato memorizzato.
Spegnimento
Alla fine di sessione di prove, una volta rientrati ai box, premere il pulsante due volte velocemente per spegnere il modulo.
Note di utilizzo
Se il modulo viene sempre utilizzato sullo stesso circuito non necessita di me-morizzare il traguardo ad ogni utilizzo, sarà sufficente l’accensione del modulo e attendere il link con il satellite, si potrà utilizzare immediatamente il cronometrag-gio.
La memorizzazione automatica del traguardo non e’ abilitata con velocita’ inferio-ri a 20 km/h.
Lo strumento considera anche la direzione di percorrenza quindi, passando in prossimità del traguardo in direzioni diverse il traguardo non viene riconosciuto per evitare falsi cronometraggi.
Test modulo Gps
Nel caso in cui il modulo Gps dovesse avere dei problemi di malfunzionamento, dopo l’accensione il Led diventerà di colore GIALLO
LISTA APPLICAZIONE CRONOMETRO GPS PER CRUSCOTTI ORIGINALI
Tutti i collegamenti sono da effettuare nel cablaggio dietro alla strumentazione Applicazioni non vincolanti si prega di controllare i collegamenti presenti sulla
moto !
KTM Modello anno Cavo MARRONE Cavo GIALLO Cavo VERDE POSITIVO +
Cavo BIANCO MASSA -
1190 RC 8 R 2009 Marrone Rosso Giallo/Arancio Marrone1190 RC 8 R 2011 Marrone Bianco/rosso Arancio Marrone
MV AGUSTA Modello anno Cavo MARRONE Cavo GIALLO Cavo VERDE POSITIVO +
Cavo BIANCO MASSA -
F 3 11>15 Marrone/Bianco Giallo/Nero Giallo/Nero BluF 4 11>15 Bianco Blu/giallo Blu/giallo Blu
TRIUMPH Modello anno Cavo MARRONE Cavo GIALLO Cavo VERDE POSITIVO +
Cavo BIANCO MASSA -
STREET TRIPLE 675 09/12 Bianco/rosso Verde/rosso Verde/rosso Nero DAYTONA 675 06/08 Bianco/rosso Verde/rosso Verde/rosso Nero
DAYTONA 675/ R 675 09/16 Bianco/rosso Verde/rosso Verde/rosso Nero
YAMAHA Modello anno Cavo MARRONE Cavo GIALLO Cavo VERDE POSITIVO +
Cavo BIANCO MASSA -
R 1 09>14 Nero/bianco Blu/bianco Marrone Nero/biancoR 1 - R 1M YEC 15>16 Nero/bianco Giallo rosso/bianco Nero/bianco
R 1- R 1M 15>16 Giallo/Nero giallo Rosso/Giallo Nero
HONDA Modello anno Cavo MARRONE Cavo GIALLO Cavo VERDE POSITIVO +
Cavo BIANCO MASSA -
CBR 1000 RR 2018 Nero/Rosso Giallo/Rosso Marrone/Bianco Verde
Note: Per R1 2015, i collegamenti dovranno essere effettuati nel connettore della centralina dei fari Xenon posizionata nella parte anteriore a sinistra della carena
LISTA APPLICAZIONE CRONOMETRO GPS PER CRUSCOTTI ORIGINALI
Tutti i collegamenti sono da effettuare nel cablaggio dietro alla strumentazione Applicazioni non vincolanti si prega di controllare i collegamenti presenti sulla
moto !
APRILIA Modello anno Cavo MARRONE Cavo GIALLO Cavo VERDE POSITIVO +
Cavo BIANCO MASSA -
RS 125 95>97 Blu Bianco/verde Verde Blu scuro RS 125 98>05 Blu Bianco/verde Verde Blu scuroRS 125 06>10 Verde Blu scuroRS 250 95>97 Bianco/nero Bianco/verde Verde/rosso Bianco/neroRS 250 98>02 Bianco/nero Bianco/verde Verde/rosso Bianco/nero
RS v1000 98>03 Bianco/blu Verde Verde/rosso Blu/verdeRS v1000 04>08 Bianco/blu Verde/rosso Verde/rosso Blu scuroTUONO 02>05 Bianco/blu Verde Verde Blu/verdeTUONO 06>10 Marrone Grigio/verde Verde/rosso Blu/verde
TUONO V4/V4 APCR 11>15 Blu/Nero Giallo/rosa Rosso/Marrone Blu/verdeRSV4 09>12 Blu/Nero Giallo/rosa Verde/rosso Blu/verde
RSV4 APCR 11> 14 Blu/Nero Giallo/rosa Verde/rosso Blu/verdeRSV4 RR/RF 15>16 Blu/Nero Giallo/rosa Verde/rosso Blu/verde
KAWASAKI Modello anno Cavo MARRONE Cavo GIALLO Cavo VERDE POSITIVO +
Cavo BIANCO MASSA -
636 03>06 Bianco/rosso Marrone/bianco Marrone/bianco Nero/gialloZX 6 R 07>10 Bianco/rosso Marrone/bianco Marrone/bianco Nero/gialloZX10 R 04>10 Bianco/rosso Marrone/bianco Marrone/bianco Nero/gialloZX10 R 11>16 Rosso/Nero Marrone/bianco Marrone/bianco Nero/giallo
DUCATI Modello anno Cavo MARRONE Cavo GIALLO Cavo VERDE POSITIVO +
Cavo BIANCO MASSA -
Monster 696/796/1100 tutti Giallo/blu Rosso/Nero Rosso/Nero NeroHypermotard 1100 08>09 Giallo/blu Rosso/Nero Rosso/Nero Nero
Hypermotard 796/1100 10>13 Giallo/Verde Rosso/Nero Rosso/Nero NeroStreetfighter tutti Blu Rosso/Nero Rosso/Nero Nero/Verde899 Panigale 13>15 Arancione pin 15 Rosso/Nero pin 8 Rosso/Giallo pin 34 Nero pin 33
959 Panigale 2016 Arancione pin 15 Rosso/Nero pin 8 Rosso/Giallo pin 34 Nero pin 33
1199 Panigale 12>16 Arancione pin 15 Rosso/Nero pin 8 Rosso/Giallo pin 34 Nero pin 33
1299 Panigale 14>16 Arancione pin 15 Rosso/Nero pin 8 Rosso/Giallo pin 34 Nero pin 33
Product Code IDmanufacturing date
